[rancid] [PATCH] junos.pm: filter negative temperatures in ShowChassisEnvironment

Aaron Dudek adudek16 at gmail.com
Wed Feb 20 17:55:32 UTC 2019


so -2 or lower works?

On Wed, Feb 20, 2019 at 12:37 PM Emille Blanc
<emille at abccommunications.com> wrote:
>
> These are all from an EX2200-C-12T-2G's, running 12.3R12.4
> We're stuck at that release for the 2200-C's, as 15.x bricks them in our environment (TSB17138 does warn to not use 15.x).
>
> > I just saw your comment in the patch that N/A only appeared for a temperature in the range -1 to 0.
>
> Correct - last I dug into this, it only reports N/A at 0 (zero), and -1 degrees. It always struck me as an odd cosmetic.
>
> -----Original Message-----
> From: Rancid-discuss [mailto:rancid-discuss-bounces at shrubbery.net] On Behalf Of Anderson, Charles R
> Sent: Wednesday, February 20, 2019 9:20 AM
> To: rancid-discuss at shrubbery.net
> Subject: Re: [rancid] [PATCH] junos.pm: filter negative temperatures in ShowChassisEnvironment
>
> My example below WAS from an EX2200.  We have some others that always report -10 (even in toasty closets)--I wonder if that is off-scale low due to a sensor failure?  I have also seen N/A in 2016, but not lately.  What software version are you running?  We are running 12.3R12-S2 on this particular outdoor EX2200.  I can try to find out what version we were running in 2016 when we last saw N/A.  I just saw your comment in the patch that N/A only appeared for a temperature in the range -1 to 0.
>
> On Wed, Feb 20, 2019 at 08:54:39AM -0800, Emille Blanc wrote:
> > Ironically, we rely on RANCID to tell us when our cabinets get too cold on such devices.
> > Mostly because our NMS is hopeless, and can't do it (Enterprise! Closed source!), so it never occurred to me to submit a patch for this.
> >
> > However, some devices (namely, EX2200's) don't understand zero, or sub-zero degrees and report it as N/A.
> > I've attached a patch to cover this circumstance.
> >
> >   # Class Item                           Status
> >   # Power FPC 0 Power Supply 0           OK
> >   # Temp  FPC 0 GEPHY1                   OK
> > - #       FPC 0 GEPHY2                   OK         N/A
> > + #       FPC 0 GEPHY2                   OK
> >   #       FPC 0 GEPHY3                   OK
> >   #       FPC 0 GEPHY4                   OK
> >   #
> >
> > -----Original Message-----
> > From: Rancid-discuss [mailto:rancid-discuss-bounces at shrubbery.net] On Behalf Of Anderson, Charles R
> > Sent: Tuesday, February 19, 2019 6:50 AM
> > To: rancid-discuss at shrubbery.net
> > Subject: [rancid] [PATCH] junos.pm: filter negative temperatures in ShowChassisEnvironment
> >
> > One of our switches is in an outdoor cabinet.  It gets below 0 sometimes so we see output like this:
> >
> >   # Temp  FPC 0 GEPHY1                   OK
> >   #       FPC 0 GEPHY2                   OK
> >   #       FPC 0 GEPHY3                   OK
> > - #       FPC 0 GEPHY4                   OK         -5 degrees C / 23 degrees F
> > + #       FPC 0 GEPHY4                   OK
> >   #
> >
> > The attached patch fixes ShowChassisEnvironment so it matches the - sign.
>
> _______________________________________________
> Rancid-discuss mailing list
> Rancid-discuss at shrubbery.net
> http://www.shrubbery.net/mailman/listinfo/rancid-discuss
>
> _______________________________________________
> Rancid-discuss mailing list
> Rancid-discuss at shrubbery.net
> http://www.shrubbery.net/mailman/listinfo/rancid-discuss



More information about the Rancid-discuss mailing list