[rancid] Re: Extreme Issue

[john heasley]

Thu, Oct 29, 2009 at 11:48:11AM -0500, Peder:
> I am having an issue getting RANCID to pull down my Extreme configs from
> Summit 200's.  I've seen several posts where others have had the same issue,
> but I haven't really seen a solution.  I am using local accounts on the
> Extreme (I tried my username and admin and they both have the same issue).
> I can ping and telnet to the extreme from the RANCID box, but it will just
> not grab the configs.  The logs just show "missed commands" and the devices
> show in the "up" file.  I am trying to pull configs from two switches and
> they both have the same issue.  I've tried this:
> 
> ./clogin  -c "show configuration detail" 192.168.1.2
> 
> It logs in, grabs the config and then just sits there.  It never closes the
> connection.  If I do the same thing from a Cisco switch that I have, it goes
> all the way thru and closes the connection just fine.

you'll have to re-run this clogin with -d and collect the debug info
near the end of the configuration dump to the hang point.  also, include
your host o/s info.

> If I do ./clogin -d 192.168.1.2, I get this (I cut off some of the beginning
> debugs as I don't think it is relevant because you can see that it actually
> does get logged in and then just sits there):
> 
> expect: set expect_out(0,string) "#"
> expect: set expect_out(1,string) "#"
> expect: set expect_out(spawn_id) "exp4"
> expect: set expect_out(buffer) " \r\n\r\n\r\nExtremeware\r\nCopyright (C)
> 1996-2004 Extreme Networks.  All rights
> reserved.\r\n===============================================================
> \r\n\r\nPress the <tab> key at any time for completions.\r\nRemember to save
> your configuration changes.\r\nS200-B:1 #"
> send: sending "\r" to { exp4 }
> 
> expect: does " " (spawn_id exp4) match regular expression "[\r\n]+"? no
> "^(.+[:.])1 ((#| \(enable\)))"? no
> "^.+(#| \(enable\))"? no
> 
> S200-B:1 #
> expect: does " \r\nS200-B:1 # " (spawn_id exp4) match regular expression
> "[\r\n]+"? yes
> expect: set expect_out(0,string) "\r\n"
> expect: set expect_out(spawn_id) "exp4"
> expect: set expect_out(buffer) " \r\n"
> expect: continuing expect
> 
> expect: does "S200-B:1 # " (spawn_id exp4) match regular expression
> "[\r\n]+"? no
> "^(.+[:.])1 ((#| \(enable\)))"? yes
> expect: set expect_out(0,string) "S200-B:1 #"
> expect: set expect_out(1,string) "S200-B:"
> expect: set expect_out(2,string) "#"
> expect: set expect_out(3,string) "#"
> expect: set expect_out(spawn_id) "exp4"
> expect: set expect_out(buffer) "S200-B:1 #"
> tty_raw_noecho: was raw = 0  echo = 1
> 
> 
> 
> Any ideas?
> 
> Peder
> 
> _______________________________________________
> Rancid-discuss mailing list
> Rancid-discuss at shrubbery.net
> http://www.shrubbery.net/mailman/listinfo.cgi/rancid-discuss