[rancid] Re: Connecting to a Cisco Service Control Engine

Lance rancid at gheek.net
Fri Jan 26 20:00:47 UTC 2007


Does it work at all on any devices that don't have a username prompt. I
have a ton of devices that don't have user prompts and mine works just
fine. I know that doesn't answer the question, but just a curious
question.

> -------- Original Message --------
> Subject: [rancid] Re: Connecting to a Cisco Service Control Engine
> From: Manuel Noriega <mnoriega at amnetcorp.com>
> Date: Fri, January 26, 2007 11:52 am
> To: "Sherrill, Justin" <jsherrill at currentcomm.net>
> Cc: rancid-discuss at shrubbery.net
>
> I had a similar situation with Tellabs equipment which don't ask for
> user or password and login immediately. What I used in .cloginrc was:
>
> add userprompt  tellabs* ">"
>
> I guess in your case something similar may work using
>
> add enableprompt  10.0.0.1 ">"
>
>
>
> Sincerely,
>
> Manuel Noriega
> ISP Engineer
>
>
> ---------------------------------------------------------------------
>
>
>
> 13 CALLE 3-40, ZONA 10
> 15 NIVEL, OFICINA 15-01
> GUATEMALA CITY, C.A.
> PBX (502) 2279 0099
> FAX (502) 2279 0003
>
> www.amnetdatos.com
>
>
> On Jan 25, 2007, at 4:07 PM, Sherrill, Justin wrote:
>
> > I've got a number of Cisco SCE units (formerly known as P-Cube).
> They
> > don't prompt for a username, just a password.  Connecting to them
> with
> > clogin will log in, but they hang once the user prompt shows.
> >
> > The prompt is the normal type that Rancid recognizes -
> > "hostname>".  It
> > appears that Rancid emits the password normally, and then waits for
> > something other than the user prompt, which leads to the timeout.  I
> > don't know what that something is.
> >
> > Looking at clogin, it appears that it should enter the password and
> > happily continue when it sees the '>' in the prompt, unless I'm
> > reading
> > it wrong.
> >
> > Will clogin look for the user prompt if the username hasn't been
> > entered?
> >
> > (Details - .cloginrc):
> >
> > add password    10.0.0.1  pass1   pass2
> > add method      10.0.0.1  {telnet}
> >
> > (what I see)
> >
> > $ ./bin/clogin -c 'show vers' 10.0.0.1
> > 10.0.0.1
> > spawn telnet 10.0.0.1
> > Trying 10.0.0.1...
> > Connected to 10.0.0.1 (10.0.0.1).
> > Escape character is '^]'.
> >
> >
> > User Access Verification
> >
> > Password:
> > hostname>
> > Error: TIMEOUT reached
> >
> > -----------------------------------------
> > Justin C. Sherrill - CURRENT Communications
> > 220 Kenneth Drive
> > Rochester, New York 14623
> > P: 585.486.0549 F: 585.486.0030
> >
> >
> >
> > ***CONFIDENTIALITY NOTICE***
> > The information in this email may be confidential and/or
> > privileged. This email is intended to be reviewed by only the
> > individual or organization named above. If you are not the intended
>
> > recipient or an authorized representative of the intended
> > recipient, you are hereby notified that any review, dissemination
> > or copying of this email and its attachments, if any, or the
> > information contained herein is prohibited. If you have received
> > this email in error, please immediately notify the sender by return
>
> > email and delete this message from your system.
> >
> > _______________________________________________
> > Rancid-discuss mailing list
> > Rancid-discuss at shrubbery.net
> > http://www.shrubbery.net/mailman/listinfo.cgi/rancid-discuss
> >
>
>
> ---------------------------------------------------------------------
> _______________________________________________
> Rancid-discuss mailing list
> Rancid-discuss at shrubbery.net
> http://www.shrubbery.net/mailman/listinfo.cgi/rancid-discuss




More information about the Rancid-discuss mailing list