|
|
This appendix describes the SES PNNI controller commands that are specific to management of the SES PNNI Controller shelf.
These commands use the same conventions as described in "SVC, SPVC, and PNNI Commands."
Shelf operation commands consist of the following command suites:
| Command | Usage | Access Level | State | Log | SNMP Support |
|---|---|---|---|---|---|
| User Commands | |||||
| addtrapmgr | Set up a new user name | 1 | active | yes |
|
| bootChange | Exit the CLI shell | any | any | yes |
|
| clrscrn | Clear the terminal screen | any | any | no |
|
| cmdhistory | View recent commands executed on the current card | any | any | no |
|
| cnfuser | Configure user information. | 1 | active | yes |
|
| copy | Copy files. | any | any | no |
|
| delete | Delete files | 1 | any | yes |
|
| dellmiloop | Remove a user name from the configured user list associated with the shelf | 1 | active | yes |
|
| dspsnmp | View user IDs that have been configured on the PXM | any | any | no |
|
| exit | Exit the CLI shell | any | any | yes |
|
| Help | View commands associated with the selected card | any | any | no |
|
| timeout | View details associated with user IDs currently active on the PXM | any | any | no |
|
| whoami | View the current login ID, access level and associated terminal port | any | any | no |
|
| Shelf Commands | |||||
addtrapmgr | Sets up an SNMP manager to receive traps. | super
| any | no |
|
bootChange | Specifies the boot IP address and gateway address of a PXM card. | service | any | yes |
|
| cc | Navigates between different cards within the shelf. | any | any | no |
|
cnfpasswd | Configures a user password. | Superuser
| active | yes |
|
cnfsnmp | Configures SNMP strings. | Superuser | active | yes |
|
deltrapmgr | Deletes a trap manager. | Superuser | active | yes |
|
| dspcd | View specified card information
Run this command on the BPX and the SES. | any | any | no |
|
dspdisk | Displays disk utilization. | any | any | no |
|
| dspcderrs | View card information for all installed cards | any | active | no |
|
dspsnmp | Displays the SNMP strings. | any | any | no |
|
dsptrapmgr | Displays details about all trap managers. | any | any | no |
|
| dspversion | View version information about the selected card. | any | any | no |
|
| resetsys | Reset the entire shelf
Run this command on the BPX and the SES. | super
| active | yes |
|
| routeShow | View the IP routing of the network layer of the operating system. | any | any | no |
|
| routestatShow | View the IP routing statistics for the network layer of the operating system | any | any | no |
|
| setrev | Sets the primary and secondary revisions of the specified slot. | super user | any | yes |
|
sesntimeout | Specifies the number of seconds of idle time for the current user-session. | Service | active | yes |
|
timeout
| Display or change the maximum time a user can be idle before the system terminates that user's session. | Service | active | yes |
|
| Node Level Commands | |||||
| addapsln | Enables APS on a specified line for the PXM | super | active | yes |
|
| addlmiloop | Enables LMI loopback line on the current card. | super | active | no |
|
| clrallcnf | Clear all configurations and restart system, using a default configuration.
Run this command on the BPX and SES. | super | active | yes |
|
| clrbecnt | Remove all statistics for APS bit-error counts. | service
| active | no |
|
| clrerr | Remove specified or all error log files. | super | any | no |
|
Clears log of errors and failures | super | any | no |
| |
| clrerrhist | Clear the LMI (Local Management Interface) statistics on the current PXM. | any | any | no |
|
| clrlog | Clear specified or all event log files.
Run this command on the BPX and SES. | super
| any | yes |
|
| cnfapsln | Set APS parameters for a line on the PXM. | super | active | yes |
|
| cnfdate | Set system date. | Super | active | yes | yes |
| cnfname | Set node name. | super | active | yes |
|
| cnfstatsmgr | Set the IP address of statistics manager. | service group | active | no |
|
| cnftime | Set system time. | super user | active | yes |
|
| cnftmzn | Set the system timezone.
| super user
| active | yes |
|
| cnftmzngmt | Set the system time zone. Run this command on the BPX and SES. | super user
| active | yes |
|
Configure the trap ip | super user
| active | yes |
| |
| delapsln | Remove APS configuration for a specified PXM line. | super user | active | yes |
|
dellmiloop | Removes LMI loopback state for a line. | super | active | no |
|
| dspapscfg | Display APS configuration for PXM lines. | any | any | no |
|
| dspbecnt | Display APS bit-error count statistics | super | active | no |
|
dspcderrs
| Displays information about card errors. | any | any | no |
|
| dspcdalms | Display card alarms. | any | any | no |
|
| dspcdstatus | Display card status. | any | any | no |
|
| dspcwmrole | View primary, secondary, tertiary, or statistics manager CWM for this node. | any | active | no |
|
| dspdate | View current system time. | any | and | no | yes |
| dspenvalms | Display environment alarms. | any | any | no |
|
| dsperr | View the contents of either all error log files or a specific error log file | any | any | no |
|
Display a log of errors and failures. | any | any | no |
| |
| dsperrhist | View configuration and state information for a broadband interface | any | any | no |
|
| dspipif | View IP configuration and statistics for one or all IP interfaces | any | any | no | no |
dsplmilink | Displays LMI links on a line. | any | active | no |
|
dsplmiloop | Displays LMI loopback state for a line. | any | active | no |
|
| dsplmilink | View the current local management interface (LMI) configurations | any | any | no |
|
| dsplog | View events and messages logged by the current PXM. In this case, this command should be run on the SES. However, it is also a command in the BPX CLI. | any | any | no |
|
| dsplogs | View information from all event log files | any | any | no |
|
| dspndalms | Display node alarms. | any | any | no |
|
| dspndparms | Display node parameters. | any | any | no |
|
| dspndstatus | Display node status. | any | any | no |
|
| dspslotalms | Display slot alarms. | any | any | no |
|
dspswalms | Displays switching alarms. | any | any | no |
|
| ipifconfig | Set IP address information for a specified IP interface on the PXM | any | any | yes |
|
restoreallcnf | Restores all configuration files saved in the CNF directory on the harddrive. | service | active | yes |
|
saveallcnf | Saves all the configuration files to the CNF directory on the harddrive. | Service | active | yes |
|
| switchapsln | Control APS line switch functions. | super user | active | yes |
|
| Redundancy Commands | |||||
| dspred | Displays redundant information. | any | any | no |
|
| switchcc | Switch core card.
Run this command on the BPX and SES. | service group | active | yes |
|
Use the addapsln command to set APS on a specified line for a PXM.
Syntax Description
addapsln <work-line><work-slot><prot-line><prot-slot><mode>
work-line | Working line number. Enter the value 1. |
work-slot | Enter value 1 or 2.
|
prot-line | Protection line number. Enter the value 1. |
prot-slot | Protection slot number. Enter the value 1 or 2. |
mode | Value to set APS architecture mode to be used on the working/protection line pair, as defined for 1+1 two backcards. Enter the value 2. |
Examples
addapsln 1 1 1 2 2
Use the addlmiloop command to add an LMI loopback line to the current card.
Syntax Description
slot | Slot number, in the range 1 - 2 |
port | Port number |
 |
Note You can activate only one PXM line on the feeder implementation of an SES node. |
To add an LMI loopback line numbered 1 to the current card (the PXM in slot [?])
Examples
addlmiloop 1.1
Use the addtrapmgr command to set up an SNMP manager to receive traps. Trap managers you add through addtrapmgr and trap managers that are added by the SNMP manager (Cisco WAN Manager or other application) do not age and are not deleted. To delete a trap manager, use either the deltrapmgr command or an SNMP Set on the intended object.
Syntax Description
addtrapmgr <ip_addr> <portnum>
ip_addr | IP address in dotted decimal format: nnn.nnn.nnn.nnn, n=0-9 and nnn < 256 |
portnum | Port number on the workstation that receives traps. The range is 0-65535. If you add a trap manager through SNMP, the default portnum is 162 |
Examples
Add a trap manager with IP address 161.10.144.56 to port 50.
spirit11.1.1.PXM.a > addtrapmgr 161.10.144.56 50
Use the adduser command to configure a user name and associated access level on the PXM.
Syntax Description
adduser <user ID> <accessLevel>
user ID | Case-sensitive name to be used as the login at the PXM. The name can consist of up to 12 characters composed of alpha and numeric characters, special characters "_" and "-". The name must begin with an alpha character and cannot contain spaces. |
accessLevel | System privilege level to be allocated for the user ID, using one of the following options:
The new user that you configure cannot be configured for an accessLevel that is higher than that defined for the current login ID. |
Examples
spirit.1.1.PXM.a > adduser fin ANYUSER Enter password: Re-enter password: spirit.1.1.PXM.a >
Use the bootChange command to specify the boot IP address and gateway address of a PXM card. The IP address you define with bootChange is used only when the PXM is in the boot state.
In the current release, the only parameters you should enter are "inet on ethernet (e)" and "gateway inet (g)." The bootChange command presents one parameter at a time. Therefore, press the Return (or Enter) key at each prompt execept for these two. The example in this description shows the two fields where you need to enter an IP address and the fields you skip.
|
Note Run this command in boot-mode only. |
Syntax Description
bootChange
Examples
Specify an IP address of 170.11.52.61 for the Ethernet port and 170.11.52.2 for the gateway IP address. The display shows all the fields that the node presents. For all fields except the ethernet and gateway prompts, press Return or Enter.
spirit11.1.1.PXM.a > bootChange '.' = clear field; '-' = go to previous field; ^D = quit boot device : lnPci processor number : 0 host name : winter file name : /users/joloughl/pxm45_002.000.014-A1.fw inet on ethernet (e) : 170.11.52.61 inet on backplane (b): host inet (h) : 170.11.25.42 gateway inet (g) : 170.11.52.2 user (u) : rli ftp password (pw) (blank = use rsh): flags (f) : 0x0 target name (tn) : pxm45-71 startup script (s) : other (o) :
Use the bye command to exit the current CLI shell.
Syntax Description
bye
Examples
spirit.1.2.PXM.a > bye (session ended)
Use the cc command to navigate from card to card on the shelf.
Syntax Description
slot number | The number of the slot that contains the card you want to work on, either 1 or 2. |
Examples
spirita.1.PXM.a > cc 2
Use the clrallcnf command to remove all configuration databases from the shelf, including configuration stored in BRAM by the shelf manager, and other configuration files currently stored on disk.
 |
Warning This is a destructive command. |
Syntax Description
clrallcnf
Examples
spirita.1.PXM.a > clrallcnf
All SM's config will be deleted, and
the shelf will be reset.
Do you want to proceed (Yes/No)? n
(command not executed)
Use the clrbecnt command to remove all the statistics for the (APS) bit-error counts
Syntax Description
clrbecnt <line>
line | Enter the value 1. |
Use the clrerr command to remove specified or all error log files. This command queries for confirmation prior to clearing the error log files from the system.
Syntax Description
clrerr [-en <error number>]
-en | Command delineator that precedes the error number entry. |
error number | Number of the log file to clear. |
-sl | Command delivered that proceeds the slot number entry. |
slot number | Number of the slot in which the selected card resides. |
Related Commands
dsperr
Examples
wilco.1.1.PXM.a > clrerr Do you want to proceed (Yes/No)? No (command not executed) wilco.1.1.PXM.a >
Use the clrerrhist command to display a log of errors and failures.
Syntax Description
clrerrhist <slot>
slot number | Optional. The number of the slot that contains the card you want to work on. Use this object to clear the log of errors and failures only on a specific slot. |
Examples
spirit11.1.1.PXM.a > clrerrhist 10 0x301f syncRam DB Reset Init from STBY failed 09/07/2000-20:44:25 ----------------------------------------------------------------------------- spirit11.1.1.PXM.a >
Use the clrlmistats command to clear the LMI (Local Management Interface) related statistics on the current PXM.
Syntax Description
clrlmistats
Examples
penguin.1.1.PXM.a > clrlmistats Enabled : 1 Port Status : 1 VPI.VCI : 3.31 Polling enable : 1 T393 : 10 N394 : 5 T394 : 10 N395 : 5 WaitStatus : 0 WaitStAck : 0 Retry Timer : 0 Retry Count : 1 Poll Timer : 6 Trans Num : 86 Status Rx : 0 Status Tx : 0 UpdtStatus Rx : 0 UpdtStatus Tx : 0 Status Enq Rx : 0 Status Enq Tx : 0 Status Ack Rx : 0 Status Ack Tx : 0 NodeStatus Rx : 0 NodeStatus Tx : 0 NodeStaAck Rx : 0 NodeStaAck Tx : 0 Bad PDU Rx : 0 Bad PDU Len Rx : 0 Unknown PDU Rx : 0 Invalid I.E. Rx: 0 Invalid Trans : 0 BPX IP Addr : 172.3.3.62 penguin.1.1.PXM.a >
Use the clrlog command to clear specified or all event log files.
Syntax Description
-log | Command delineator that precedes the log slot entry. |
log slot | Number of the file that you want to clear from the event log file. |
Related Commands
dsplog
Examples
wilco.1.1.PXM.a > clrlog Do you want to proceed (Yes/No)? Yes wilco.1.1.PXM.a >
Use the clrscrn command to remove the contents of the control terminal screen. After this command executes, only the current command line prompt displays on the terminal screen.
Syntax Description
Examples
flyers01.1.17.AUSM.a > clrscrn flyers01.1.17.AUSM.a >
Use the cmdhistory command to view the last 10 commands executed on the current card.
Syntax Description
cmdhistory
Examples
spirit4.1.2.PXM.a > cmdhistory Size of cmdHistory is currently 10 line(s) 1 dspconcnt 2.39.45 2 dsplmistats 3 dsplmiloop 4 dsplm 5 clrportcnt 6 dspportcnts 7 dspportcnt 8 dspportcnt 1 9 dsplmistats 10 cmdhistory spirit4.1.2.PXM.a >
Use the cnfapsln command to set APS parameters for a specified line on the PXM card.
Syntax Description
cnfapsln <line> <SFBER> <SDBER> <Revertive> <WTR> <Direction> <KIK2>
line | OC-3 line number. Enter the value 1. |
SFBER | Signal failure BER threshold, in the range 3-5. 5 = signal failure BER threshold = 10 ^^ -5. |
SDBER | Signal degrade BER threshold, in the range 5-9. 5 = signal degrade BER threshold = 10 ^^ -5. |
WTR | Number of minutes to wait before attempting to switch back to the working line, in the range 1-12. This setting is not applicable if the line is configured in non-revertive mode (Revertive set to 1). |
Direction | Value to set the switching direction for either unidirectional or bidirectional.
2 = Bidirectional: This APS line supports switching both ends of the line. |
Revertive | Value to set the APS revertive or non-revertive function. · 1 = Non-revertive · 2 = Revertive |
K1K2 | To to enable or disable the K1/K2 inband protocol on the protection line. · 1 = enable · 2 = disable |
Examples
To set the APS working line 1 on the active PXM card in slot 1 to have a signal failure BER threshold of 10^^-5, a signal degrade BER threshold of 10^^-5, to enable switch back after signal failure or degradation has cleared, to wait 2 minutes before attempting to switch back, to make switching bidirectional, and to enable the K1/K2 inband protocol on the protection line
flyers01.1.1.PXM.a > cnfapsln 1 5 5 2 2 2 1 flyers01.1.1.PXM.a >
Use the cnfdate command to set the system date.
Syntax Description
cnfdate <mm/dd/yyyy>
mm/dd/yyyy |
|
Examples
wilso.1.1.PXM.a> cnfdate 12/17/1999
Use the cnfname command to set the name of the SES PNNI node. This namewill not be propagated throughout the network.
Syntax Description
cnfname <name>
name | Name of this SES PNNI node, consisting of up to 8 alpha-numeric characters. |
Examples
spirita.1.PXM.a > cnfname NewName cnfname: Configured this node name to NewName Successfully. NewName.1.PXM.a >
Use the cnfpasswd command to set the password for a specified User ID or type the command without arguments to change your own password.
Syntax Description
user_id | User name |
Examples
spirit4.1.2.PXM.a > cnfpasswd Enter existing password: Enter new password: Re-enter new password: spirit4.1.2.PXM.a >
Use the cnfsnmp command to configure SNMP Strings. You can configure only one of these strings with a single execution of cnfsnmp.
Syntax Description
cnfsnmp <-community [string <ro | rw>]> <-contact [string]> <-location [string]>
-
-community | Keyword that establishes the community access string to permit access to SNMPv1 protocol. The string acts like a password and permits access to the SNMP Protocol. Further, the access of either read-only or read-write allows operations on MIB Objects according to the setting. The setting can be either "ro" for read-only or "rw" for read-write. The default is read-only With read-only, authorized management stations are only able to retrieve MIB objects. With read-write access, authorized management stations are able to retrieve and modify MIB objects. |
-contact | Keyword that specifies the system contact string for sysContact MIB object in MIB-II. The string in this case is text that describes the contact. For example, the contact could be an administrator's email address. The default is no text. |
-location | Keyword that specifies the location of the system. The default is no text. The system location string is used for sysLocation MIB object in MIB-II. |
Examples
Configure various community strings.
spirit11.1.1.PXM.a > cnfsnmp community ro spirit11.1.1.PXM.a >cnfsnmp community comaccess spirit11.1.1.PXM.a >community string "comaccess" , read-only access spirit11.1.1.PXM.a >cnfsnmp community comaccess ro spirit11.1.1.PXM.a >community string "comaccess" read-only access spirit11.1.1.PXM.a >cnfsnmp community superaccess rw spirit11.1.1.PXM.a >community string "superaccess" , read-write access
Give an email address for t he system contact
spirit11.1.1.PXM.a > cnfsnmp contact Dial System, Email :
Specify the location of the system as Building 3, Room 214.
node19.8.PXM.a >cnfsnmp location Building 3/Room 214
Use the cnfstatsmgr command to set the IP address of the CWM that manages statistics for this node.
Syntax Description
cnfstatsmgr <IP Address>
Examples
cnfstatsmgr 172.29.4.50
Use the cnftime command to set the system time.
Syntax Description
cnftime <hh:mm:ss>
hh:mm:ss | Hour, month, and seconds. |
Examples
wilco.1.1.PXM.a > cnftime 11:20:30
Use the cnftmzn command to set the system time zone.
Syntax Description
cnftmzn <timezone>
timezone |
|
Examples
wilco.1.1.PXM.a > cnftmzn PST
Use the cnftmzngmt command to set the system time zone offset value.
Syntax Description
cnftmzngmt <gmtoffset>
gmtoffset | -12, -11, -10 10, 11, 12 |
Examples
wilco.1.1.PXM.a > cnftmzngmt -8
Use the cnftrapip command to configure the trap ip.
Syntax Description
cnftrapip <ip address>
ip address | ip address where traps will be configured. |
pirit11.1.1.PXM.a > cnftrapip usage:cnftrapip <ipaddress>
Use the cnfuser command to add or change user information.
Syntax Description
cnfuser <-u user id>
user id | User name |
password | User password |
accessLevel | System privilege level to be allocated for the user ID, using one of the following options:
The new user that you configure cannot be configured for an accessLevel that is higher than that defined for the current login ID. |
Examples
spirita.1.PXM.a > cnfuser -u myname -p passw123 -l ANYUSER
Use the copy command to copy files.
Syntax Description
copy <source file>
source file | Source file to be copied. |
destination file | Destination file. |
Examples
spirita.1.PXM.a > copy version vers
spirita.1.PXM.a > ll
size date time name
-------- ------ ------ --------
512 MAR-22-2000 19:37:56 SM <DIR>
512 MAR-22-2000 19:37:56 FW <DIR>
512 MAR-22-2000 19:37:56 DIAG <DIR>
512 MAR-22-2000 19:37:56 STATS <DIR>
512 MAR-22-2000 19:37:56 TMP <DIR>
512 MAR-22-2000 19:37:56 CNF <DIR>
512 MAR-22-2000 19:37:56 RPM <DIR>
512 MAR-22-2000 19:37:56 SCT <DIR>
36 MAY-21-2000 03:31:34 version
512 MAR-22-2000 11:40:52 LOG <DIR>
512 MAR-22-2000 11:40:58 CUT <DIR>
512 MAY-09-2000 10:45:04 SHMDB <DIR>
1749807 MAY-16-2000 07:10:14 pxm_diag_1.1.04.o
36 MAY-21-2000 04:41:28 vers
In the file system :
total space : 819200 K bytes
free space : 808145 K bytes
Use the delapsln command to delete APS from a line on the PXM card.
Syntax Description
delapsln <workingline>
workingline | Working line number. Enter the value 1. |
Examples
delapsln 1
Use the delete command to remove any files on the disk.
Syntax Description
delete <file name>
file name | Name of the file to be removed. |
Examples
spirita.1.PXM.a > delete <any_file>
Use the dellmiloop command to remove LMI loopback state for a line.
|
Note You can activate only one PXM line on the feeder implementation of an SES node. |
Syntax Description
dellmiloop <slot.port>
slot | Slot number, in the range 1 - 2 |
port | Port number |
To delete lmi loopback line from the current PXM.
spirit11.1.1.PXM.a > dellmiloop 1.1
Use the deltrapmgr command to delete a trap manager. . The deltrapmgr command requires an IP address for deletion. To see existing trap managers, use dsptrapmgr.
Syntax Description
deltrapmgr <ip_addr>
|
|
Examples
Delete trap manager with IP address 161.10.144.56.
spirit11.1.1.PXM.a > deltrapmgr 161.10.144.56
Use the deluser command to remove a user from the list of users on the SES node. The system does not allow you to delete a user with a privilege level higher than the level at which you execute the command. For example, if the current user privilege is 2, you cannot delete a user at level 1. No screen output appears unless an error occurs.
Syntax Description
user ID | User name, consisting of up to 12 characters |
Examples
spirita.1.PXM.a > deluser myname
Use the dspapscfg command to view aps configuration information.
Syntax Description
dspapscfg
Examples
spirita.1.PXM.a > dspapscfg SlotLine Type SFBER SDBER WTR Dir Revert K1K2 ----------------------------------------------------- 1.1&2.1 1+1_2 3 5 1 UNI NRV ENA
Use the dspapsln command to view the current APS line parameters on the PXM card.
Syntax Description
dspapsln
Examples
spirita.1.PXM.a > dspapsln SlotLine Type Act W_LINE P_LINE APS_ST CDType Dir Revt LastUsrSwReq ------------------------------------------------------------------------ 1.1&2.1 1+1_2 2.1 ALM YEL OK OC-3 UNI NRV NO_REQUEST
Use the dspbecnt command to view the APS bit-error information for a generic line.
Syntax Description
dspbecnt <line>
line | Working line number. Enter the value 1. |
Use the dspcd command to view hardware and firmware information about the selected PXM.
Syntax Description
dspcd <slot number>
slot number | Slot number of the installed PXM, either 1 or 2. |
Examples
spirita.2.PXM.s > dspcd
spirita.2
System Rev:01.00 Jul. 17, 2000
16:31:25 PST
SES-CNTL Node Alarm:NONE
Slot Number 1 Redundant Slot: 2
Front Card Upper Card Lower Card
---------- ---------- ----------
Inserted Card: PXM1_OC3 UIA BackCard MMF_4_OC3
Reserved Card: PXM1_OC3 UIA BackCard MMF_4_OC3
State: Active Active Active
Serial Number: SBK033300F8 SBK033000QP SBK03340075
Prim SW Rev: 1.0(231)A1 --- ---
Sec SW Rev: 1.0(231)A1 --- ---
Cur SW Rev: 1.0(231)A1 --- ---
Boot FW Rev: 1.0(1) --- ---
800-level Rev: A0 A0 A0
Orderable Part#: 800-05610-02 800-03688-01 800-05053-01
CLEI Code: BAA4HCZAAA BAI9Y00AAA BA2IKNJBAA
Reset Reason: On Reset From Shell
Card Alarm: NONE
Failed Reason: None
Miscellaneous Information:
spirita.2
System Rev:01.00 Jul. 17, 2000
16:31:25 PST
SES-CNTL Node Alarm:NONE
Crossbar Slot Status: No Crossbar
Alarm Causes
------------
NO ALARMS
Use the dspcdalms command to view the summary of node card alarms. This includes line alarms, port alarms, and channel alarms.
Syntax Description
dspcdalms
Examples
spirita.1.PXM.a > dspcdalms Node Card Alarm Summary Line Alarm Slot 1 Critical 2 Major 0 Minor 0 Port Alarm Slot 1 Critical 0 Major 0 Minor 0 Channel Alarm Slot 1 Critical 0 Major 0 Minor 0
Use the dspcderrs command to display information about card errors.
Syntax Description
dspcderrs
Examples
spirit11.1.1.PXM.a > dspcderrs
dspcderrs 08/05/95-18:53:05 tRootTask 3 Task failed : scm 09/05/95-09:14:08 tRootTask 3 Task failed : scm value = 0 = 0x0spirit11.1.1.PXM.a >
Use the dspcds command to view status of all installed cards in the SES PNNI Controller.
Syntax Description
dspcds
Examples
spirita.1.PXM.a > dspcds
spirita System Rev: 01.00 May. 21, 2000 05:34:12 PST
Backplane Serial No: 12345 Bp HW Rev: 00.00 GMT Offset: -8
Node Alarm: CRITICAL
Card Front/Back Card Alarm Redundant Redundancy
Slot Card State Type Status Slot Type
--- ---------- -------- -------- ------- -----
01 Active/Active PXM1_OC3 NONE 02 PRIMARY SLOT
02 Standby/Active PXM1_OC3 NONE 01 SECONDARY SLOT
03 Empty --- --- --- ---
04 Empty --- --- --- ---
05 Empty --- --- --- ---
06 Empty --- --- --- ---
07 Empty --- --- --- ---
spirita.1.PXM.a >
Use the dspcdstatus command to view the status of the card alarms.
Syntax Description
dspcdstatus <slotnumber>
slot number | Command delineator that preceeds the slot number entry |
Examples
spirita.1.PXM.a > dspcdstatus Defaulting to logical slot 1. Logical Slot 1 Physical Slot 1 Card Alarm Status - Type LINE Severity CRITICAL
Use the dspcwmrole command to view the IP address of the CWM in the primary, secondary, tertiary, or statistics master for this node.
Syntax Description
dspcwmrole <primary | secondary | tertiary | statsmaster>
Examples
dspcwmrole primary
Use the dspdisk command to display disk utilization. A likely application of dspdisk is a routine check of disk utilization by running a script that includes this command.
|
Note The capacity of the disk is very large relative to typical usage and therefore does not present potential restrictions. The output shows the allocated space rather than the physical capacity of the drive. |
Syntax Description
dspdisk <disk partition>
disk partition Optional. Displays the space utilization by each directory under that partition or directory in addition to the disk summary information. The disk partition can be one of the following:
Note If you do not state the disk partition, only the summary of total and free space on each disk partition is displayed.
|
Note dspdisk will not handle multiple partitions/directories on the command-line. |
Examples
spirit11.1.1.PXM.a > dspdisk
========================================================== Partition C: Allocated Size: 800 MB Free Space: 574 MB Partition D: Allocated Size: 600 MB Free Space: 564 MB Partition E: Allocated Size: 100 MB Free Space: 99 MB Partition F: Allocated Size: 800 MB Free Space: 799 MB
==========================================================
spirit11.1.1.PXM.a> dspdisk c: ========================================================== Partition C: Allocated Size: 800 MB Free Space: 634 MB Partition D: Allocated Size: 200 MB Free Space: 175 MB Partition E: Allocated Size: 100 MB Free Space: 99 MB Partition F: Allocated Size: 1000 MB Free Space: 999 MB ========================================================== Disk usage for c: ========================================================== Error: could not stat() c: spirit11.1.1.PXM.a>
Use the dspenvalms command to view environment alarms. This includes line alarms, port alarms, and channel alarms.
Syntax Description
dspenvalmsalms [temp|psu|fan|vnom]
Examples
spirita.1.PXM.a > dspenvalms spirita System Rev: 01.00 May. 21, 2000 08:26:56 PST SES-CNTL Node Alarm: CRITICAL ENVIRONMENTAL ALARM STATE INFO ^Notification Disabled Alarm Type Unit Threshold DataType Value State ---------------- ---- -------------- -------- ---------- ------------- Temperature <= 50 Celsius 26 Normal Power Supply A1 none None none Normal Power Supply A2 none None none Missing Power Supply A3 none None none Missing DC Voltage A 42 to 54 VoltsDC 49 Normal Power Supply B1 none None none Missing Power Supply B2 none None none Missing Power Supply B3 none None none Missing DC Voltage B 42 to 54 VoltsDC 0 Normal Fan Tray 1 >= 2000 RPM 2790 Normal Fan Tray 2 >= 2000 RPM 2754 Normal Fan Tray 3 >= 2000 RPM 2700 Normal Fan Tray 4 >= 2000 RPM 2652 Normal Fan Tray 5 >= 2000 RPM 2676 Normal Type <CR> to continue, Q<CR> to stop: dsp
Use the dsperr command to view the contents of either all error log files or a specific error log file.
Syntax Description .
dsperr [-en <error slot>
-en | Command delineator that precedes the error slot entry. |
error slot | Number of the error log file. |
-sl | Command delineator that preceeds the slot number entry |
slot number | Command delineator that preceeds the slot number entry |
Examples
spirit3.1.1.PXM.a > dsperr
----------
Stack Trace:
0x801e5714 vxTaskEntry + c: sysTaskSetup()
0x80024d2c sysTaskSetup + 58: rmm_main()
0x800dff7c rmm_main +624: rmm_process_message()
0x800df764 rmm_process_message + 98: rmm_delete_seat()
0x800e0f54 rmm_delete_seat + ac: ipc_remove_seat()
0x800d1140 ipc_remove_seat + 50: ipc_renumber_as_slave()
0x800d0a10 ipc_renumber_as_slave +208: my_free()
0x800d3430 my_free + 8: ssiFree()
0x8001c378 ssiFree + 8c: ssiEvent()
0x800274dc ssiEvent +11c: ssiEvent()
0x800277bc ssiEvent +3fc: sysStackTrace()
----------
No Dump Trace before the event
spirit3.1.1.PXM.a >
spirita.1.PXM.a > dsperr
Error Log for Slot 01: Error Num 42
Firmware version: 001.000.000.000_swtools Product Id: 3
Timestamp: 05/21/2000-04:41:33 Node name: spirita
Section Number 0:
Event Logged:
01-00124 05/21/2000-04:41:33 DB2S-4-DBSYNC_NULLPARA
E:00042 tDbgCmdTsk 0x800e9f58
ssiFRIsDirReplicated: Invalid Parameter: NULL pointer or NULL string for Path Name
Section Number 1:
Stack Trace:
0x805ce684 vxTaskEntry +00c: sysTaskSetup+0()
0x800720e4 sysTaskSetup +09c: cliCmdTask+0()
0x80197924 cliCmdTask +478: cliCmdExec+0()
0x80197098 cliCmdExec +270: cliRemove+0()
0x8019841c cliRemove +184: ssiFRIsDirReplicated+0()
0x800e9f58 ssiFRIsDirReplicated +068: ssiEvent+0()
0x8005e0dc ssiEvent +24c: ssiEventMsgReport+0()
0x8005e618 ssiEventMsgReport +284: ssiStackTrace+0()
--------------
Type <CR> to continue, Q<CR> to stop: q
Use the dsperrhist command to display a log of errors and failures.
Syntax Description
dsperrhist
slot number | Optional. The number of the slot that contains the card you want to work on. Use this object to disaply the log of errors and failures only on a specific slot. |
Examples
spirit11.1.1.PXM.a > dsperrhist
Log of Errors and Failures: Entry#--Event#---EventName-------------------------------TimeStamp----------- 01 0x1000 RAM sync error 08/11/2000-16:50:34 02 0x1000 RAM sync error 08/11/2000-16:51:54 03 0x301f syncRam DB Reset Init from STBY failed 08/11/2000-16:53:12 04 0x0007 SHM_CDF_MAX_RESETS_REACHED 08/11/2000-16:54:28 05 0x301f syncRam DB Reset Init from STBY failed 08/11/2000-16:58:16 06 0x1000 RAM sync error 08/11/2000-16:59:36 07 0x301f syncRam DB Reset Init from STBY failed 08/11/2000-17:00:56 08 0x301f syncRam DB Reset Init from STBY failed 08/11/2000-17:01:35 09 0x1000 RAM sync error 09/07/2000-20:43:05 Type <CR> to continue, Q<CR> to stop:
spirit11.1.1.PXM.aspirit11.1.1.PXM.a> dsperrhist 2
Log of Errors and Failures: Entry#--Event#---EventName-------------------------------TimeStamp----------- 01 0x1000 RAM sync error 07/07/2000-09:29:31 02 0x1000 RAM sync error 07/07/2000-09:30:51 03 0x301f syncRam DB Reset Init from STBY failed 07/07/2000-09:32:11 04 0x0007 SHM_CDF_MAX_RESETS_REACHED 07/07/2000-09:33:19 05 0x1000 RAM sync error 07/07/2000-22:25:06 06 0x1000 RAM sync error 07/07/2000-22:26:26 07 0x301f syncRam DB Reset Init from STBY failed 07/07/2000-22:27:46 08 0x0007 SHM_CDF_MAX_RESETS_REACHED 07/07/2000-22:28:54 09 0x1000 RAM sync error 07/08/2000-04:29:58 Type <CR> to continue, Q<CR> to stop:
Use the dspif command to view configuration and state information for the selected broadband interface.
Syntax Description
dspif <if_num>
if_num | Interface number, in the range 1-32. |
Examples
To view configuration and state information for broadband interface number 1:
spirit3.1.1.PXM.a > dspif 1 ifNum Status Line ingrPctBw egrPctBw minVpi maxVpi ------------------------------------------------------ 1 Ena 1 10 10 0 19 spirit3.1.1.PXM.a >
Use the dspipif command to view configuration and statistics information associated with one or all IP interfaces.
Syntax Description
dspipif [interface]
interface | Optional interface name, using one of the following terms:
|
Examples
spirita.1.PXM.a > dspipif
Use the dspipifcache command to view interface cache translation table for one or all interfaces.
Syntax Description
dspipifcache [interface]
interface | Optional interface type, stated as atm0. |
Examples
spirita.1.PXM.a > dspipifcache
spirita System Rev: 01.00 May. 21, 2000 06:03:36 PST
SES-CNTL Node Alarm: CRITICAL
IP CONNECTIVITY INTERFACE CACHE
Interface IpAddress VcId Age(Flush@120000) Flags
--------------------------------------------------------------------------
No Entries
Use the dsplmilink command to display LMI links on a line.
Syntax Description
dsplmilink
Examples
spirit11.1.1.PXM.a > dsplmilink
Use the dsplmiloop command to display LMI loopback state for a line.
Syntax Description
dsplmiloop
Examples
spirit11.1.1.PXM.a > dsplmiloop
TRK LMI LOOP STATUS ----------------------- 2.1 Disabled
Use the dsplmistats command to view the current local management interface (LMI) configurations.
Syntax Description
Examples
spirit3.1.1.PXM.a > dspilmistats
Polling Enabled: 1 Port Status : 1 VPI.VCI : 3.31 T393 : 10 N394 : 5 T394 : 10 N395 : 5 WaitStatus : 0 WaitStAck : 0 Retry Timer : 0 Retry Count : 1 Poll Timer : 1 Trans Num : 210 Status Rx : 55762 Status Tx : 53550 UpdtStatus Rx : 0 UpdtStatus Tx : 0 Status Enq Rx : 53550 Status Enq Tx : 55762 Status Ack Rx : 0 Status Ack Tx : 0 NodeStatus Rx : 43918 Type <CR> to continue, Q <CR> to stop:
Use the dsplog command to view events and messages logged by the selected PXM. The most recent events appear at the top of the list. You can display the entire list of logged messages by typing the dsplog command without arguments, or you can specify the individual card for which you want to view log information.
|
Note This document describes the dsplog command on the SES. This command is also in BPX CLI. |
dsplog -log <EventLog# > -mod <ModuleName> -sev <Severity#> -sl <Slot# > -task <TaskName>
-tge <MM/DD/YYYY-HH:MM:SS> -tle <MM/DD/YYYY -HH:MM:SS>
-log | Command delineator that precedes the EventLog# entry |
EventLog# | Number of the event log item |
-mod | Command delineator that precedes the Module Name entry |
Module Name | Module name |
-sev | Command delineator that precedes the Severity # entry |
Severity # | Severity number |
-sl | Command delineator that precedes the Slot# entry |
Slot# | Slot number that contains the card associated with the event log |
-task | Command delineator that precedes the TaskName entry |
TaskName | Task name |
-tge | Command delineator that precedes the MM/DD/YYYY-HH:MM:SS entry, to define time greater than, or equal. |
MM/DD/YYYY-HH:MM:SS | Month, day, year, hour, minute, second |
-tle | Command delineator that precedes the MM/DD/YYYY-HH:MM:SS entry, to define time less than, or equal. |
MM/DD/YYYY-HH:MM:SS | Month, day, year, hour, minute, second. |
Examples
spirit3.1.1.PXM.a > dsplog
02-12037 09/22/2000-17:31:09 FTPD-7-FTPDLIB3
FtpdServ1 0x8027e204
EVNT:ftp user logged OFF:username= superuser
02-12036 09/22/2000-17:31:09 FTPD-7-FTPDLIB3
FtpdServ1 0x8027d3b8
EVNT:ftp user logged ON:username= superuser
02-12035 09/22/2000-17:31:09 FTPD-7-FTPDLIB3
FtpdServ1 0x8027e204
EVNT:ftp user logged OFF:username= superuser
02-12034 09/22/2000-17:31:09 FTPD-7-FTPDLIB3
FtpdServ1 0x8027d3b8
EVNT:ftp user logged ON:username= superuser
02-12033 09/22/2000-17:31:09 FTPD-7-FTPDLIB3
FtpdServ1 0x8027e204
EVNT:ftp user logged OFF:username= superuser
02-12032 09/22/2000-17:31:09 FTPD-7-FTPDLIB3
FtpdServ1 0x8027d3b8
EVNT:ftp user logged ON:username= superuser
02-12031 09/22/2000-17:31:09 FTPD-7-FTPDLIB3
FtpdServ1 0x8027e204
EVNT:ftp user logged OFF:username= superuser
02-12030 09/22/2000-17:31:09 FTPD-7-FTPDLIB3
Use the dsplogs command to view PXM log files.
Syntax Description
dsplogs
spirit11.1.1.PXM.a > dsplogs Current Event log number: 20 Event log 20: C:/LOG/event20.log starting timestamp: 09/22/2000-12:31:04 Event log 19: C:/LOG/event19.log starting timestamp: 09/22/2000-00:21:01 Event log 18: C:/LOG/event18.log starting timestamp: 09/20/2000-22:42:11 Event log 17: C:/LOG/event17.log starting timestamp: 09/19/2000-16:05:52 Event log 16: C:/LOG/event16.log starting timestamp: 09/19/2000-01:35:08 Event log 15: C:/LOG/event15.log starting timestamp: 09/18/2000-16:32:47 Event log 14: C:/LOG/event14.log starting timestamp: 09/18/2000-07:20:02 Event log 13: C:/LOG/event13.log starting timestamp: 09/17/2000-17:50:13 Event log 12: C:/LOG/event12.log starting timestamp: 09/16/2000-22:24:37 Event log 11: C:/LOG/event11.log starting timestamp: 09/16/2000-01:35:50 Event log 10: C:/LOG/event10.log starting timestamp: 09/15/2000-22:05:42 Type <CR> to continue, Q<CR> to stop:
Use the dspndalms command to view the node alarms. This includes clock alarms, switching alarms, shelfslot alarms, environment alarms, and card alarms.
Syntax Description
dspndalms
Examples
spirita.1.PXM.a > dspndalms Node Alarm Summary Alarm Type Critical Major Minor Clock Alarms 0 0 0 Switching Alarms 0 0 0 Shelf Slot Alarms 0 0 0 Environment Alarms 0 0 0 Alarms From Cards 2 0 0
Use the dspndstatus command to view the status of the node alarms.
Syntax Description
dspndstatus
Examples
spirita.1.PXM.a > dspndstatus Total Alarms = 2 Node Alarm Status - Type LINE ALARM Severity CRITICAL
Use the dspred command to view redundancy information.
Syntax Description
dspred
Examples
spirit11.1.1.PXM.a > dspred spirita System Rev: 02.00 May. 22, 2000 11:25:02 GMT SES-CNTL Node Alarm: NONE Primary Primary Primary Secondary Secondary Secondary Redundancy SlotNum Type State SlotNum Type State Type ------- ------- ------- --------- --------- --------- ---------- 1 PXM1 Active 2 PXM1 Standby 1-1
Use the dspslotalms command to view the slot alarms. This includes card alarms, card hardware alarms, disk alarms, and interface card alarms.
Syntax Description
dspslotalms
Examples
spirita.1.PXM.a > dspslotalms Node Slot Alarm Summary Card Alarm Critical 0 Major 0 Minor 0 Card Hardware Critical 0 Major 0 Minor 0 Disk Alarm Critical 0 Major 0 Minor 0 Interface Card Critical 0 Major 0 Minor 0
Use the dspsnmp command to display disk utilization.
Syntax Description
dspsnmp
Examples
spirit11.1.1.PXM.a > dspsnmp
Unknown System Rev:01.00 Sep. 27, 2000 06:25:35 PST SES-CNTL Node Alarm:MAJOR Community: ro System Location: System Contact
Use the dspswalms command to display alarms for circuits on the PXM.
Syntax Description
dspswalms
Examples
spirit11.1.1.PXM.a > dspswalms
Node Switching Alarm Summary Card Crossbar Critical 0 Major 0 Minor 0 Crossbar Fabric Critical 0 Major 0 Minor 0 Humvee Alarm Critical 0 Major 0 Minor 0 espses3.2.PXM.a >
Use the dsptrapmgr command to display all the details about a trap manager.
Display details about all existing trap managers. The dsptrapmgr output shows:
Of these elements, the IP address and port number result from addtrapmgr.
Syntax Description
dsptrapmgr
Examples
spirit11.1.1.PXM.a > dsptrapmgr
node19.8.PXM.a > dsptrapmgr
ipAddress PortNum RowStatus ReadTrapFlag NextTrapSeqNum
--------------- ------- ---------- ------------ --------------
171.71.55.21 2500 Add Off 0
172.29.65.87 2500 Add Off 348
172.71.59.21 2500 Add Off 0
LastTrapSeqNum: 385
NumOfValidEntries: 3
Use the dspusers command to view the user IDs that have been added to the PXM configuration. The screen shows the user name and highest privilege level and displays the number of those levels above user-privilege.
Syntax Description
dspusers [-u -userid]
-u <user id> | User id. principle string length of 1-12.. |
Examples
wilco.1.1.PXM.a > dspusers UserId AccessLevel ------------------------- cisco CISCO_GP service SERVICE_GP superuser SUPER_GP raoul GROUP3 duke GROUP1 wilco.1.1.PXM.a >
Use the dspversion command to view version information about the selected card.
Syntax Description
dspversion
Examples
spirita.1.PXM.a > dspversion
Image Type Shelf Type Card Type Version Built On
---------- ---------- ---------- ------------ ------------
Runtime MGX PXM1 1.0(0) May 17 2000, 19:36:59
Boot MGX PXM1 1.0(39)B1 -
Use the exit command to exit the current CLI shell.
Syntax Description
exit
Examples
spirit4.1.2.PXM.a > exit (session ended)
Use the Help command to view commands associated with the current card. The Help command also takes arguments and filters the commands based on the argument string.
Syntax Description
Examples
spirita.1.PXM.a > Help
Available commands
------------------
?
abortofflinediag
abortrev
addaddr
addapsln
addchan
addcon
addfltset
addlmiloop
addmaster
addpnni-node
addpnni-summary-addr
addpnport
addprfx
addred
addserialif
addslave
addtrapmgr
adduser
Type <CR> to continue, Q<CR> to stop:
.Use the ipifconfig command to set IP address information for a specified IP interface on the PXM.
Syntax Description
ipifconfig <interface> [<ip_address>] [up|down] [netmask Mask] [broadcast <broad_addr>]
[arp | noarp] [svc|nosvc] [pvc | nopvc] [default|nodefault] [clrstats]
interface | Interface type, as associated with one of the following entries:
| ||
ip_address | IP address of the interface. This setting is mandatory if the interface has never been configured. | ||
up | down | Optional: sets interface status as either active (up) or deactive (down). | ||
netmask <mask> | Optional: network mask value for the interface. Net_mask is decided by type of IP address entered
| ||
broad_addr | Optional: broadcast address for the interface. | ||
arp | noarp | Optional: Enable (arp) or disable (noarp) ARP on the interface. Default = enabled if the interface supports ARP. | ||
svc | nosvc | Optional: Enable (svc) or disable (nosvc) SVC on the interface. Default = enabled if the interface supports SVC. | ||
pvc | nopvc | Optional: enable (pvc) or disable (nopvc) PVC on the interface. Default = disabled | ||
default | nodefault | Optional: Set this interface as either the default route or disable default route on this interface. | ||
clrstats | Optional: Remove all interface and SVC/PVC statistics for this interface. |
Examples
ipifconfig atm0 10.1.2.95
Use the ifShow command to view the contents of all the currently configured interfaces.
Syntax Description
ifShow
Examples
spirit4.1.2.PXM.a > ifShow
lnPci (unit number 0):
Flags: (0x63) UP BROADCAST ARP RUNNING
Internet address: 172.29.23.149
Broadcast address: 172.29.23.255
Netmask 0xffff0000 Subnetmask 0xffffff00
Ethernet address is 00:c0:43:00:2d:c7
Metric is 0
Maximum Transfer Unit size is 1500
599468 packets received; 34476 packets sent
0 input errors; 0 output errors
0 collisions
lo (unit number 0):
Flags: (0x69) UP LOOPBACK ARP RUNNING
Internet address: 127.0.0.1
Netmask 0xff000000 Subnetmask 0xff000000
Metric is 0
Maximum Transfer Unit size is 4096
4 packets received; 4 packets sent
0 input errors; 0 output errors
0 collisions
sl (unit number 0):
Flags: (0x71) UP POINT-TO-POINT ARP RUNNING
Internet address: 0.0.0.0
Destination Internet address: 0.0.0.0
Netmask 0xff000000 Subnetmask 0xff000000
Metric is 0
Maximum Transfer Unit size is 576
0 packets received; 0 packets sent
0 input errors; 0 output errors
0 collisions
atm (unit number 0):
Flags: (0x43) UP BROADCAST TRAILERS ARP RUNNING
Internet address: 172.1.1.149
Broadcast address: 172.1.1.255
Netmask 0xffff0000 Subnetmask 0xffffff00
Ethernet address is 00:00:00:00:00:00
Metric is 0
Maximum Transfer Unit size is 1500
0 packets received; 47272 packets sent
0 input errors; 47272 output errors
0 collisions
spirit4.1.2.PXM.a >
Use the logout command to exit the current CLI shell.
Syntax Description
logout
Examples
spirit4.1.2.PXM.a > logout (session ended)
Use the memShow command to view the current memory map.
Syntax Description
memShow
Examples
spirit4.1.2.PXM.a > memShow status bytes blocks avg block max block ------ --------- -------- ---------- ---------- current free 2967104 37 80192 2879008 alloc 2561600 1774 1443 - cumulative alloc 241511616 1019558 236 - spirit4.1.2.PXM.a >
Use the resetcd command to reset the selected PXM, and to gracefully terminate all current applications on the card.
Syntax Description
resetcd <slot number> [-f]
slot | Slot number of the installed PXM, either 1 or 2. |
-f | (optional) Clears the fail state on the slot. |
Examples
spirita.1.PXM.a > resetcd The card in slot number 1, will be reset. Please confirm action Do you want to proceed (Yes/No)? n (command not executed)
Use the resetsys command to reset the SES shelf.
Syntax Description
resetsys
Examples
spirita.1.PXM.a > resetsys This command resets the entire shelf, a destructive command. Please confirm now! Do you want to proceed (Yes/No)? y Syncing ... C: Syncing ... D: Syncing ... E: Syncing ... F: Warning: firmware reset on active PXM card by cisco@console (session ended)
Use the restoreallcnf command to restore all configuration files saved in the CNF directory on the harddrive.
Syntax Description
restoreallcnf <-f filename>
-f (filename) |
|
|---|---|
|
|
Examples
spirita.1.PXM.a > restoreallcnf Usage :restoreallcnf -f FILENAME [-v] -f:FILENAME is the zip file for configuration option -v:print out the files restored ( default:not ) spirita.1.PXM.a > restoreallcnf -f Unknown_01_200009270622 The current configuration will be replaced with the contents of the specified file and the shelf will be rebooted. Do you want to proceed (Yes/No)? y
Use the routeShow command to view the current IP routing of the network layer of the operating system.
Syntax Description
routeShow
Examples
spirit4.1.2.PXM.a > routeShow ROUTE NET TABLE destination gateway flags Refcnt Use Interface ------------------------------------------------------------------------ 0.0.0.0 172.29.23.149 1 1 21778 lnPci0 0.0.0.0 172.29.23.1 3 0 2755 lnPci0 172.1.1.0 172.1.1.149 1 0 0 atm0 172.29.23.0 172.29.23.149 1 2 5275 lnPci0 ------------------------------------------------------------------------ ROUTE HOST TABLE destination gateway flags Refcnt Use Interface ------------------------------------------------------------------------ 0.0.0.0 0.0.0.0 5 0 0 sl0 127.0.0.1 127.0.0.1 5 1 0 lo0 172.29.23.3 172.1.1.149 5 0 3555 atm0 172.29.23.5 172.1.1.149 5 0 3304 atm0 172.29.23.7 172.1.1.149 5 0 3335 atm0 171.71.29.18 172.1.1.149 5 0 3304 atm0 172.29.23.18 172.1.1.149 5 0 3304 atm0 172.29.23.28 172.1.1.149 5 0 6127 atm0 172.29.23.29 172.1.1.149 5 1 6065 atm0 171.71.29.32 172.1.1.149 5 0 5842 atm0 171.71.29.44 172.1.1.149 5 0 3304 atm0 172.29.23.53 172.1.1.149 5 0 3304 atm0 171.71.29.59 172.1.1.149 5 0 3304 atm0 171.71.28.126 172.1.1.149 5 0 3309 atm0 ------------------------------------------------------------------------ spirit4.1.2.PXM.a >
Use the routestatShow command to view the current IP routing statistics for the network layer of the operating system.
Syntax Description
routestatShow
Examples
spirit4.1.2.PXM.a > routestatShow
routing:
0 bad routing redirect
0 dynamically created route
0 new gateway due to redirects
0 destination found unreachable
11095 uses of a wildcard route
spirit4.1.2.PXM.a >
Use the saveallcnf command to saves all the configuration files to the CNF directory on the harddrive.The 'saveallcnf' command can be time-consuming. The shelf must not provision new circuits while this command is running. Do not run this command unless the shelf configuration is stableor you risk corrupting the saved configuration file.
Syntax Description
saveallcnf
Examples
spirit11.1.1.PXM.a > saveallcnf
Do you want to proceed (Yes/No)? y
saveallcnf:shelf configuration saved in C:/CNF/Unknown_01_200009270622.zip.
Use the sesntimeout command to specify the number of seconds of idle time for the current user-session. If you do not specify a timeout period, the system displays the current timeout. At the end of the session, the system logs you out.
To disable the session timeout function, specify 0 seconds.
Syntax Description
sesntimeout [time_out]
time_out | Number of idle seconds time allowed for the session. |
Examples
spirit11.1.1.PXM.a > sesntimeout 300 The timeout period for this session is now set to 300 second(s)
spirit11.1.1.PXM.a >
Use the setrev command to set the primary and secondary revisions of the slot specified.
Syntax Description
setrev <slot><primaryversion><secondaryversion>
slot | Slot number of the card for which the version will be set. |
primary version | The primary version number to which the card will be set. |
primary version | The secondary version number to which the card will be set |
|
Note Use the revision number for both primary and secondary versions to start a new version. |
Examples
spirita.1.PXM.a > setrev 1.0(0) 1.0(0) one or more card(s) in logical slot 1 will be reset. Do you want to proceed (Yes/No)? n (command not executed)
Use the switchapsln command to control APS switching actions. This function applies to OC-3 lines.
Syntax Description
switchapsln <line number> <operation>
line number | OC-3 line number on which to apply APS. Enter the value 1. |
operation | Alpha character to set type of APS switch functionality to use on the PXM line.
|
Syntax Description
switchapsln 1 f
switchapsln s 2
Use the switchcc command to reverse the roles of the active and the standby PXM. After you use this command, the PXM previously designated as the active PXM becomes the standby, and the PXM previously designated as the standby becomes the active PXM.
Syntax Description
switchcc
Examples
spirit11.1.1.PXM.a > switchcc Do you want to proceed (Yes/No)?
Use the timeout command to display or change the maximum time a user can be idle before the system terminates that user's session. The units of measure are seconds. To change the timeout period, type a number that is less than or equal to 600 after the timeout command.
Syntax Description
timeout [timeout_period]
timeout_period | (Optional) Number of seconds for the new timeout period. The maximum is 600. If you do not enter a timeout_period, the system displays the current timeout period. To disable the session timeout function, enter 0. |
Examples
spirit11.1.1.PXM.a > timeout 0 The timeout period for this session is now set to 0 second(s)
espses3.2.PXM.a > timeout 40000
The timeout period for this session is now set to 40000 second(s)
espses3.2.PXM.a > timeout 22
The timeout period for this session is now set to 22 second(s)
espses3.2.PXM.a > timeout 5
Err:input timed out
(session ended)
Use the who command to view details associated with user IDs currently active on the PXM.
Syntax Description
who
Examples
spirit.1.1.PXM.a > who Port Slot Idle UserId From ------------------------------------------------------------- telnet.01 * 7 0:00:00 cisco 171.71.25.240 spirit.1.1.PXM.a >
Use the whoami command to view the current login ID, access level and associated terminal port.
Syntax Description
whoami
Examples
spirit.1.1.PXM.a > whoami User ID: cisco Access Level: CISCO_GP Terminal Port: telnet.01 spirit.1.1.PXM.a >
Posted: Thu Sep 28 15:10:48 PDT 2000
Copyright 1989-2000©Cisco Systems Inc.