MGX 8850 Command Line Interface

where:

aimux_grp	AIMUX group number to be added. The range is 1 through 8.
list_of_lines	list of physical lines to be included in "aimux_grp" separated by dots. The range is 1 through 8.

Related Commands

delaimgrp, cnfaimgrps, dspaimgrp, dspaimgrps

Cards on Which This Command Executes

AUSM

Attributes

Log: Yes State: Active Privilege: 1-2

Example

 spirit4.1.18.PXM.a > addaimgrp 2 1 3.4.5 

Description

Add IMA group 2 as UNI with lines 3, 4, and 5.

System Response

none

where:

chan	is a channel number in the range 16-1015.
port	is a port number in the range 1-192 for T1; 1-248 for E1.
dlci	is the DLCI in the range 0-1023.
cir	is committed information rate: 0-1536000 bps for T1; 0-2048000 bps for E1.
chan_type	is the channel type indicator with a range of 1-5: 1=NIW 2=SIW-transparent 3=SIW-translation 4=FUNI 5=frame forwarding
CAC_enable	is the optional Connection Admission Control enable, where 1=enable, 2=disable (default).
mastership	specifies whether the current end is the master or slave: 1=master, and 2=slave
locnsap	is the local node name, slot, and port in NSAP format. This 20-byte string is the hexadecimal form of the ASCII characters.
rmtvpi	is the remote VPI. The range is from 1 to 65535.
rmtvci	is the remote VCI. The range is from 1 to 65535.
rmtnsap	is the remote node name, slot, and port in NSAP format. This 20-byte string is the hexadecimal form of the ASCII characters.

Possible errors are:

• One or more parameters is invalid.

• Channel already exists.

• Port may not be up.

On FRSM-VHS:

where:

chan	is a channel number in the range 16-4015.
port	is a port number in the range 1-256.
dlci	is the DLCI in the range 0-1023.
cir	is committed information rate: 0-1536000 bps for T1; 0-2048000 bps for E1.
chan_type	is the channel type indicator with a range of 1-5: 1=NIW 2=SIW-transparent 3=SIW-translation 4=FUNI 5=frame forwarding
serv_type	is a number representing the service type: · 1 specifies CBR, which stands for Constant Bit Rate. · 2 specifies VBR, which stands for Variable Bit Rate. · 3 specifies ABR, which stands for Available Bit Rate. · 4 specifies UBR, which stands for Unspecified Bit Rate.
CAC_enable	is the optional Connection Admission Control enable, where 1=enable, 2=disable (default).
mastership	specifies whether the current end is the master or slave: 1=master, and 2=slave
locnsap	is the local node name, slot, and port in NSAP format. This 20-byte string is the hexadecimal form of the ASCII characters.
rmtvpi	is the remote VPI. The range is from 1 to 65535.
rmtvci	is the remote VCI. The range is from 1 to 65535.
rmtnsap	is the remote node name, slot, and port in NSAP format. This 20-byte string is the hexadecimal form of the ASCII characters.

ON CESM-8T1E1:

addchan <chan_num> <port_num> <Ces_Cas> <partial_fill> <cond_data> <cond_sig> <mastership> <locnsap> <rmtvpi> <rmtvci> <rmtnsap>

where:

chan	is a channel number in the range 32-279.
port	is the port number. For T1, the range is 1-192. For E1, the range is 1-248.
Ces_Cas	is a number that represents the signalling selection. If type is set to 5 (CCS or Common Channel Signaling), it means that this particular channel is carrying signaling information only. All channels on a line should have the same value. 1=basic. 2=E1 CAS. 3=DS1 superframe CAS. 4=DS1 extended superframe CAS. 5=CCS
partial_fill	specifies the number of bytes to partially fill a cell for different lines: 0=a fully filled cell. This is the default. 20-47 cells for structured E1. 25-47 for structured T1. 33-47 for unstructured T1 or E1.
cond_data	specifies a data-conditioning value. For UDT, cond_data is always 255. For SDT, the range is 0-255.
cond_sig	specifies a condition signal in the range 0-15.
mastership	specifies whether the current end is the master or slave. 1=master, and 2=slave
locnsap	is the local node name, slot, and port in NSAP format. This 20-byte string is the hexadecimal form of the ASCII characters.
rmtvpi	is the remote VPI in the range 1-65535.
rmtvci	is the remote VCI in the range 1-65535. It should have the same value as the logical port number of the remote end point.
rmtnsap	is the remote node name, slot, and port in NSAP format. This 20-byte string is the hexadecimal form of the ASCII characters.

Possible errors are:

• One or more parameters is invalid.

• Channel already exists.

• Port may not be up.

Related Commands

ON CESM-T3E3:

where:

chan	is a channel number, 32 for CESM-T3E3
port	is the port number. 1 for CESM-T3E3
cond_sig	specifies a condition signal in the range 0-15.
mastership	specifies whether the current end is the master or slave. 1=master, and 2=slave
locnsap	is the local node name, slot, and port in NSAP format. This 20-byte string is the hexadecimal form of the ASCII characters.
rmtvpi	is the remote VPI in the range 1-65535.
rmtvci	is the remote VCI in the range 1-65535. It should have the same value as the logical port number of the remote end point.
rmtnsap	is the remote node name, slot, and port in NSAP format. This 20-byte string is the hexadecimal form of the ASCII characters.

Possible errors are:

• One or more parameters is invalid.

• Channel already exists.

• Port may not be up.

Related Commands

delchan, dspchan, dspchans

Cards on Which This Command Executes

PXM, FRSM, CESM

Attributes

Log: Yes State: Active Privilege: 1-2

where:

channel number	channel number has a range of 16-1015
connection type	connection type is either 1 for VPC (Virtual Path Connection) or 2 for VCC (Virtual Path Connection).
port number	port number is in the range 1-8
vpi	The Virtual Path Indicator (VPI) has a value in the range 0-255
vci	The Virtual Channel Indicator (VCI) has a value in the range 0-65535
service type	is a number representing the service type: · 1 specifies CBR. (Constant Bit Rate) · 2 specifies VBR. (Variable Bit Rate) · 3 specifies ABR. (Available Bit Rate) · 4 specifies UBR. (Unspecified Bit Rate)
mastership	specifies whether the current end is the master or slave. 1=master, and 2=slave
locnsap	is the local node name, slot, and port in NSAP format. This 20-byte string is the hexadecimal form of the ASCII characters.
rmtvpi	is the remote VPI in the range 1-65535.
rmtvci	is the remote VCI in the range 1-65535. It should have the same value as the logical port number of the remote end point.
rmtnsap	is the remote node name, slot, and port in NSAP format. This 20-byte string is the hexadecimal form of the ASCII characters.

Related Commands

delcon, dspcons, dspcon

Cards on Which This Command Executes

AUSM

Attributes

Log: No State: Any Privilege: Any

Example

spirit4.1.18.AUSM.a > addchan 16 2 1 1 1 3 1

Description

Add a VCC connection to channel 16 on port 1 with vpi=1, vci=1, ABR service type, and an egress queue number of 1

System Response

none

where:

chan_num

A number in the range: · For FRSM-8T1/E1, 16-1015 · For FRSM-T3/E3/HS2, 16-2015 · For FRSM-2CT3, 16-4015 · For PXM, 16-1024 · For AUSM, 16-1015 · For CESM-8T1/E1, 32-279 · For CESM-T3/E3, one connection starting at 32

Related Commands

delchanloop, tstcon, tstdelay

Cards on Which This Command Executes

FRSM, AUSM, CESM

Attributes

Log: Yes State: Active Privilege: 1-4

where:

port number	port number is in the range 1-192 for T1 or 1-248 for E1.
DLCI	is the DLCI in the range 0-1023.
CIR	is the committed information rate in the range 0-1536000 bps for T1; 0-2048000 bps for E1.
channel type	is a number indicating the type of connection on this channel: 1=NIW (network interworking) 2=SIW-transparent (service interworking without any SDU translation) 3=SIW-translation (service interworking with SDU translation) 4=FUNI (frame relay UNI) 5=frame forwarding.
Adm_cntrl	is the Connection Admission Control toggle, which is optional. 1 = enable CAC, 2 = disable CAC. The default is 2 (disable CAC).
controller_type	is the signalling controller type, where: signalling controller type is either: 1 PVC (PAR), or 2 SPVC (PNNI) The default is 1 PVC (PAR)
mastership	sets whether the connection is the master or the slave, where: 1 = master, 2 = slave The default is 2 (slave).
RemoteEndConID	is the node name, slot number, port number, and DLCI or the node name, slot number, port number, Controller ID, and DLCI for a Frame Relay endpoint. where Controller ID is either: 1 (PAR), 2 (PNNI), or 3 (TAG) or the node name, slot number, port number, and VPI.VCI for an ATM endpoint.

On the FRSM-2CT3:

where:

port number	port number is in the range 1-256.
DLCI	is the DLCI in the range 0-1023.
CIR	is the committed information rate in the range 0-1536000 bps
channel type	is a number indicating the type of connection on this channel: 1=NIW (network interworking) 2=SIW-transparent (service interworking without any SDU translation) 3=SIW-translation (service interworking with SDU translation) 4=FUNI (frame relay UNI) 5=frame forwarding.
egress service type	is a number indicating the type of egress service provided on this channel: 1=highpriorityQ (typically committed bit rate connections) 2=rtVBRQ (real-time variable bit rate connections) 3=nrtVBRQ (non real-time variable bit rate connections) 4=aBRQ (available bit rate connections) 5=uBRQ (unspecified bit rate connections).
Adm_cntrl	is the Connection Admission Control toggle, which is optional. 1 = enable CAC, 2 = disable CAC. The default is 2 (disable CAC).
controller_type	is the signalling controller type, where: signalling controller type is either: 1 PVC (PAR), or 2 SPVC (PNNI) The default is 1 PVC (PAR)
mastership	sets whether the connection is the master or the slave, where: 1 = master, 2 = slave The default is 2 (slave).
RemoteEndConID	is the node name, slot number, port number, and DLCI or the node name, slot number, port number, Controller ID, and DLCI for a Frame Relay endpoint. where Controller ID is either: 0 (PAR), 1 (PNNI), or 2 (TAG) or the node name, slot number, port number, and VPI.VCI for an ATM endpoint.

On the FRSM-2T3/2E3:

where:

port number	port number is in the range 1-2.
DLCI	is the DLCI in the range 0-1023.
CIR	is the committed information rate in the range 0-44210000 bps for 2T3, 0-34010000 bps for 2E3
channel type	is a number indicating the type of connection on this channel: 1=NIW (network interworking) 2=SIW-transparent (service interworking without any SDU translation) 3=SIW-translation (service interworking with SDU translation) 4=FUNI (frame relay UNI) 5=frame forwarding.
egress service type	is a number indicating the type of egress service provided on this channel: 1=highpriorityQ (typically committed bit rate connections) 2=rtVBRQ (real-time variable bit rate connections) 3=nrtVBRQ (non real-time variable bit rate connections) 4=aBRQ (available bit rate connections) 5=uBRQ (unspecified bit rate connections).
Adm_cntrl	is the Connection Admission Control toggle, which is optional. 1 = enable CAC, 2 = disable CAC. The default is 2 (disable CAC).
controller_type	is the signalling controller type, where: signalling controller type is either: 1 PVC (PAR), or 2 SPVC (PNNI) The default is 1 PVC (PAR)
mastership	sets whether the connection is the master or the slave, where: 1 = master, 2 = slave The default is 2 (slave).
RemoteEndConID	is the node name, slot number, port number, and DLCI or the node name, slot number, port number, Controller ID, and DLCI for a Frame Relay endpoint. where Controller ID is either: 0 (PAR), 1 (PNNI), or 2 (TAG) or the node name, slot number, port number, and VPI.VCI for an ATM endpoint.

On the FRSM-HS2:

where:

port number	port number is in the range 1-2.
DLCI	is the DLCI in the range 0-1023.
CIR	is the committed information rate in the range 0-51840000 bps
channel type	is a number indicating the type of connection on this channel: 1=NIW (network interworking) 2=SIW-transparent (service interworking without any SDU translation) 3=SIW-translation (service interworking with SDU translation) 4=FUNI (frame relay UNI) 5=frame forwarding.
egress service type	is a number indicating the type of egress service provided on this channel: 1=highpriorityQ (typically committed bit rate connections) 2=rtVBRQ (real-time variable bit rate connections) 3=nrtVBRQ (non real-time variable bit rate connections) 4=aBRQ (available bit rate connections) 5=uBRQ (unspecified bit rate connections).
Adm_cntrl	is the Connection Admission Control toggle, which is optional. 1 = enable CAC, 2 = disable CAC. The default is 2 (disable CAC).
controller_type	is the signalling controller type, where: signalling controller type is either: 1 PVC (PAR), or 2 SPVC (PNNI) The default is 1 PVC (PAR)
mastership	sets whether the connection is the master or the slave, where: 1 = master, 2 = slave The default is 2 (slave).
RemoteEndConID	is the node name, slot number, port number, and DLCI or the node name, slot number, port number, Controller ID, and DLCI for a Frame Relay endpoint. where Controller ID is either: 0 (PAR), 1 (PNNI), or 2 (TAG) or the node name, slot number, port number, and VPI.VCI for an ATM endpoint.

On the AUSM:

addcon master <port number> <vpi> <vci> <Conn type> <Service Type> <SlaveConID> [PAR | PNNI]

where:

slave	indicates the slave end of the connection.
master	indicates the master end of the connection.
port number	port number is in the range 1-8.
vpi	vpi has a value in the range 0-255.
vci	vci has a value in the range 0-65535.
Conn type	is the connection type. Connection Type: 0 - VCC, non zero - Local VP Id of the VPC(1 to 20(UNI)/100(STI)/340(NNI)).
Service Type	is the service type: 1=CBR, 2=VBR, and 3=ABR.
SlaveConID	is the node name, slot number, port number, vci, and vpi of the slave end. This parameter applies only at the master end.
PAR | PNNI	is the optional controller specification.

On CESM 8T1/E1:

where:

port number	port number is in the range 1-192 for T1, 1-248 for E1.
signalling type	CAS: Channel associated signalling set to one of the following four values: 1=basic. 2=E1 CAS. 3=DS1 superframe CAS. 4=DS1 extended superframe CAS.
partial_fill	specifies the number of bytes to partially fill a cell for different lines. The value for partial fill is in the range 0-47. A partial fill value of 0 (or 47) means fully filled cells. The lower limit for structured T1 is 25. The value for partial fill of structured T1cells is in the range 25-47. The lower limit for structured E1 is 20. The value for partial fill of structured E1cells is in the range 20-47. The lower limit for unstructured T1/E1 is 33. The value for partial fill of unstructured T1/E1cells is in the range 33-47.
cond_data	Conditional data is sent on the line when there is an underflow and also towards the network when forming dummy cells. For UDT, cond_data is always 255. For SDT, the range is 0-255.
cond_signalling	Conditional signalling is sent on the line when there is an underflow and also towards the network when forming dummy cells. The cond_signalling range is 0-15.
controller_type	is the signalling controller type, where: signalling controller type is either: 1 PVC (PAR), or 2 SPVC (PNNI) The default is 1 PVC (PAR)
mastership	sets whether the connection is the master or the slave, where: 1 = master, 2 = slave The default is 2 (slave).
RemoteEndConID	is the node name, slot number, port number, and DLCI or the node name, slot number, port number, Controller ID, and DLCI for a Frame Relay endpoint. where Controller ID is either: 0 (PAR), 1 (PNNI), or 2 (TAG) or the node name, slot number, port number, and VPI.VCI for an ATM endpoint. Note: the slot number should be set to 0 (zero) to point to the active PXM.

Related Commands

delcon, dspcons, dspcon

Cards on Which This Command Executes

PXM, FRSM, CESM, AUSM

Attributes

Log: Yes State: Active Privilege: Any

Example

spirit4.1.18.AUSM.a > addcon 16 2 1 1 1 3 1

Description

Add a VCC connection to channel 16 on port 2 with vpi=1, vci=1, ABR service type, and an egress queue number of 1

System Response

none

where:

group_num	IMA group number to be added (1-8)
port_type	Port type to be added (1-UNI, 2-NN1)
list_of_links	list of links to be included in group_num separated by dots

Related Commands

dspimagrp, dspimagrpcnt, dspimagrps, dspimainfo, dspimalncnt

Cards on Which This Command Executes

AUSM

Attributes

Log: Yes State: Active Privilege: 1-2

Example

 spirit4.1.88.AUSM.a > addimagrp 2 1 3.4.5 

Description

Add IMA group 2 as UNI with lines 3, 4, and 5.

System Response

none

where:

T3 line number	SRM-3T3 T3 line number in the format slot.line where slot can be either 15 or 31, and the port range is 1-3. Slot number 15 is used for the cards in slot and 15 and 16, whichever is active and slot 31 is used for cards in 31 and 32.
T1 line number	start T1 line number within the T3 line (range 1-28)
Target Slot number	T1 service module slot number to be linked, where Target Slot number = 1-6|9-14|17-22|25-30
Slot line number	T1 line number in the slot to be linked (range 1-4 or 1-8) depending upon the ports in the service module

Related Commands

dsplink, dellink

Cards on Which This Command Executes

PXM

Attributes

Log: No State: Active Privilege: Any

Example

 spirit4.1.8.PXM.a > addlink 15.2 1 3 5 

Description

Add a link between the T1 line 1 within T3 line 2 on the SRM-3T3 card in slot 15 and T1 line number 5 on the T1 service module in slot 3.

System Response

none

On a PXM:

where:

• -ds3 indicates a T3 line number follows.

line number is in the format slot.port, where slot is either 7, 15, or 31 and port is a value in the range 1-n, and n is the highest numbered port on the card.

• -e3 indicates an E3 line number follows.

line number is in the format slot.port, where slot is either 7, 15, or 31 and port is a value in the range 1-n, and n is the highest numbered port on the card.

• -sonet indicates an OC-3 or OC-12 line number follows.

• line number is in the format slot.port, where slot must always be 7, and port is a value in the range 1-n, and n is the highest numbered port on the card.

Related Commands

dellmiloop, dsplmiloop

Cards on Which This Command Executes

FRSM, AUSM, CESM, PXM

Attributes

Log: No State: Active Privilege: 1

Example

spirit4.1.8.PXM.a > addlmiloop 1

Description

Add an LMI loopback line numbered 1 to the current card (the PXM in slot 8)

System Response

none

On a PXM:

where:

• -ds3 indicates a T3 line number follows.

line number is in the format slot.port, where slot is either 7, 15, or 31 and port is a value in the range 1-n, and n is the highest numbered port on the card.

• -e3 indicates an E3 line number follows.

line number is in the format slot.port, where slot is either 7, 15, or 31 and port is a value in the range 1-n, and n is the highest numbered port on the card.

• -sonet indicates an OC-3 or OC-12 line number follows.

line number is in the format slot.port, where slot must always be 7, and port is a value in the range 1-n, and n is the highest numbered port on the card.

Related Commands

cnfln, delln, dspln

Cards on Which This Command Executes

PXM, FRSM-series, AUSM, SRM-3T3, CESM-series, VISM

Attributes

Log: No State: Active Privilege: 1 (Any on PXM)

Example

spirit4.1.8.PXM.a > addln 1

Description

Add a line numbered 1 to the current card (the PXM in slot 8)

System Response

none

On FRSM HS1:

Syntax

where:

<line number>	value from 1-2 used for HSSI, 1-4 used for X.21
<line type>	value from 1-2 where 1: DCE 2: DTE
<line rate>	value from 48kbps-52Mbps

Syntax

where:

<line number>	value from 1-2 used for HSSI, 1-4 used for X.21
<loop type>	value from 1-4 where 1: Front-card 2: Metallic 3: Remote 4: No Loop
<line rate>	value from 1-3 where 1: LoopA/B (HSSI) 2: Local loop (X.21) 3: Unloop

where:

line number

a value in the range 1-n, where n is the highest numbered port on the card.

For the PXM:

where:

• -ds3 indicates a T3 line number follows.

line number is in the format slot.port, where slot is either 7, 15, or 31 and port is a value in the range 1-n, and n is the highest numbered port on the card.

• -e3 indicates an E3 line number follows.

line number is in the format slot.port, where slot is either 7, 15, or 31 and port is a value in the range 1-n, and n is the highest numbered port on the card.

• -sonet indicates an OC-3 or OC-12 line number follows.

line number is in the format slot.port, where slot must always be 7, and port is a value in the range 1-n, and n is the highest numbered port on the card.

Related Commands

dellnloop

Cards on Which This Command Executes

PXM, AUSM, FRSM, CESM

Attributes

Log: No State: Active Privilege: Service (Any on PXM)

where:

aimux_grp	AIMUX group to which lines should be added (1-8)
list_of_lines	list of lines in the AIMUX group separated by dots

Related Commands

dellnsfmaimgrp

Cards on Which This Command Executes

AUSM

Attributes

Log: Yes State: Active Privilege: 1-2

Example

spirit4.1.18.AUSM.a > addlns2aimgrp 2 1.2

Description

Add lines 1 and 2 to IMA group 2.

System Response

none

where:

port_num	numbers in the range 1-32 are valid
line_num	value ranging from 1 to 4 for OC3
Pc_bw	percentage of bandwidth in the range 1 - 100
min_vpi	VPI (Virtual Path Identifier) has a value in the range 0-255
max_vpi	VPI (Virtual Path Identifier) has a value in the range 0-255

Syntax for PXM OC12 back cards

where:

port_num	numbers in the range 1-32 are valid
line_num	value is 1 for OC12
Pc_bw	percentage of bandwidth in the range 1 - 100
min_vpi	VPI (Virtual Path Identifier) has a value in the range 0-255
max_vpi	VPI (Virtual Path Identifier) has a value in the range 0-255

Syntax for PXM T3/E3 back cards

where:

port_num	numbers in the range 1-32 are valid
line_num	value ranging from 1 to 2 for T3/E3
Pc_bw	percentage of bandwidth in the range 1 - 100
min_vpi	VPI (Virtual Path Identifier) has a value in the range 0-255
max_vpi	VPI (Virtual Path Identifier) has a value in the range 0-255

Syntax for FRSM-8T1E1 cards

where:

port_num	numbers in the range 1-192 are valid for FRSM-8T1 and 1-248 for FRSM-8E1
line_num	value ranging from 1 to 8
ds0_speed	is the bit rate for the DS0. Type a "1" for 56Kbps or a "2" for 64Kbps.
begin_slot	beginning timeslot number in the T1 or E1 frame
num_slot	number of consecutive timeslots in the T1 or E1 frame
port_type	is either 1, 2, or 3: 1 = frame relay, 2 = FUNI, 3=frame forwarding

Syntax for FRSM-2T3E3 cards

where:

port_num	numbers in the range 1-2 are valid for FRSM-2T3 or FRSM-2E3
line_num	value ranging from 1 to 56
ds0_speed	is the bit rate for the DS0. Type a "1" for 56Kbps or a "2" for 64Kbps.
begin_slot	beginning timeslot number in the T1 or E1 frame
num_slot	number of consecutive timeslots in the T1 or E1 frame
port_type	is either 1, 2, or 3: 1 = frame relay, 2 = FUNI, 3=frame forwarding

Syntax for FRSM-2CT3 cards

where:

port_num	numbers in the range 1-256 are valid for FRSM-2CT3
line_num	value ranging from 1 to 56
ds0_speed	is the bit rate for the DS0. Type a "1" for 56Kbps or a "2" for 64Kbps.
begin_slot	beginning timeslot number in the T1 or E1 frame
num_slot	number of consecutive timeslots in the T1 or E1 frame
port_type	is either 1, 2, or 3: 1 = frame relay, 2 = FUNI, 3=frame forwarding

Syntax for FRSM-HS2 cards

where:

port_num	numbers in the range 1-2 are valid for FRSM-HS2
line_num	value ranging from 1 to 56
ds0_speed	is the bit rate for the DS0. Type a "1" for 56Kbps or a "2" for 64Kbps.
begin_slot	beginning timeslot number in the T1 or E1 frame
num_slot	number of consecutive timeslots in the T1 or E1 frame
port_type	is either 1, 2, or 3: 1 = frame relay, 2 = FUNI, 3=frame forwarding

Syntax for CESM-8T1E1 cards

where:

port_num	numbers in the range 1-192 are valid for CESM-8T1 and 1-248 for CESM-8E1
line_num	value ranging from 1 to 8
begin_slot	beginning timeslot number in the T1 or E1 frame
num_slot	number of consecutive timeslots in the T1 or E1 frame
port_type	is either 1, 2, or 3: 1 = structured, 2 = unstructured, 3=framing on VC disconnect

Syntax for CESM-T3E3 cards

<where:

port_num	The only valid entry for port_num is 1 for CESM-T3E3
line_num	value is 1 for CESM-T3E3

Related Commands

addportlpbk, cnfport, delport, dspport, dspports

Cards on Which This Command Executes

PXM, FRSM, CESM

Attributes

Log: Yes State: Active Privilege: 1 (Any on PXM)

Example

node501.1.1.CESM.a > addport 1 1 1 24 1

Description

Add port 1 on line 1 with DS0 timeslots 1 through 24 assigned as structured.

System Response

none

where:

redPrimarySlotNum	is slot number of the slot containing the primary card of the card pair. The range is 1-6, 9-14, 17-22, and 25-30.
redSecondarySlotNum	is slot number of the slot containing the secondary card of the card pair. The range is 1-6, 9-14, 17-22, and 25-30.
RedType	is type of redundancy, where 1 = 1:1, and 2 = 1:N.

Related Commands

dspred, delred

Cards on Which This Command Executes

PXM

Attributes

Log: No State: Active Privilege: Any

Example

node501.1.7.PXM.a > addred 1 4 1

Description

Add 1:1 redundancy between the card in slot 4 and the card in slot 1.

System Response

none

where:

ipaddr	The IP address assigned to the trap manager: its format is nnn.nnn.nnn.nnn., where n = 0-9 and nnn < 256.
.portnum	The port the trap manager uses to receive traps. The default is 162.

Related Commands

deltrapmgr, cnftrapmgr, dsptrapmgr, xcnftrapmgr

Cards on Which This Command Executes

PXM

Attributes

Log: Yes State: Active Privilege: SuperUser

Example

node501.1.7.PXM.a > addtrapmgr 161.10.144.56 162

Description

Add a trap manager with the IP address of 161.10.144.56 to port 162.

System Response

none

where:

user ID	name for the user. The name can be up to twelve characters. The name can consist of letters, special characters "_" and "-" and numbers. It must begin with a letter and cannot contain spaces. The name is case sensitive.
accessLevel	privilege is the highest level of access the user has. The choices are: GROUP1, GROUP2, GROUP3, GROUP4, GROUP5, or ANYUSER

Related Commands

dspusers, deluser

Cards on Which This Command Executes

PXM

Attributes

Log: Yes State: Active Privilege: 5-6

Example

spirit.1.7.PXM.a > adduser fin ANYUSER

Description

Add a user named fin with privilege level ANYUSER.

System Response

Enter password:
Re-enter password:
 
 
spirit.1.7.PXM.a >

Related Commands

Help

Cards on Which This Command Executes

AUSM

Attributes

Log: No State: Any state Privilege: 1-6

Example

mogul3.1.10.AUSMB8.a > aimhelp

Description

Display the Help screen for the AUSM service module.

System Response

 
AUSM-8P Commands
 
  addcon          :  Add a Connection
  addimagrp       :  Add an IMA group
  addln           :  Add a line
  addlnloop       :  Configure a line in local loopback
  addlns2imagrp   :  Add lines to an existing IMA group
  clralmcnt       :  Clear DS1 alarm count
  clralmcnts      :  Clear alarm count for all DS1 lines
  clralm          :  Clear the DS1 line alarms
  clrchancnt      :  Clear Channel Counters
  clrchancnts     :  Clear Channel Counters for all channels
  clralms         :  Clear DS1 alarms on all lines
  clrimagrpcnt    :  Clear IMA group Counters
  clrimalncnt     :  Clear IMA counters on a particular line
  clrportcnt      :  Clear Port Counters
  clrportcnts     :  Clear Port Counters for all ports
  clrsarcnt       :  Clear SAR channel counters
  clrsarcnts      :  Clear SAR counters for all channels
  clrslftst       :  Clear self test results
  clrimatst       :  clear IMA test procedure
 
Type <CR> to continue, Q<CR> to stop:
 
  cnfchanfst      :  Configure the channel foresight parameters
  cnfchanq        :  Configure the channel queue parameters
  cnffst          :  Configure foresight params of a card
  cnfportq        :  Configure Egress queue parameters
  cnfimagrp       :  Configure an IMA group
  cnfilmi         :  Configure ILMI parameters of a port
  cnfln           :  Configure DS1/E1 line
  cnflnloop       :  Configure DS1/E1 line
  cnfplpp         :  Configure DS1/E1 line
  cnfslftst       :  Configure self test parameters
  cnfsvcrange     :  Partition Resource between PVCs & SVCs
  cnfupccbr       :  Configure UPC parameters of CBR connection
  cnfupcvbr       :  Configure UPC parameters of VBR connection
  cnfupcabr       :  Configure UPC parameters of ABR connection
  cnfupcubr       :  Configure UPC parameters of UBR connection
  cnfimatst       :  Enable the IMA test procedure
  cnfimaalmparm   :  COnfigure the IMA alaram Integration UP and DOWN times
  copychans       :  Copy a template connection
  delimagrp       :  Delete an IMA group
  delcon          :  Delete a connection
  delln           :  Delete DS1 line
  dellnloop       :  Remove a DS1 line from local loopback
  dellnsfmimagrp  :  Delete lines from an existing IMA group
  dnport          :  Down an ATM port
  dspalm          :  Display DS1 alarms on a line
  dspalmcnf       :  Display DS1 alarm configuration
  dspalmcnt       :  Display alarm count for DS1 line
  dspalms         :  Display DS1 alarms on all lines
  dspcd           :  Display card information
  dspchancnt      :  Display channel counters
  dspcon          :  Display connection configuration
  dspcons         :  Display all the configured connections
  dspfeature      :  Display the features
  dspfst          :  Display the card Foresight params
  dspilmi         :  Display ILMI parms of a port
  dspilmicnt      :  Display ILMI counters of a port
  dspimagrp       :  Display all parms configured for an IMA group
  dspimagrpcnt    :  Display IMA group Counters
  dspimagrps      :  Display the configured IMA groups
  dspimalncnt     :  Display IMA counters on a particular line
  dspimatst       :  Display IMA test status
  dspimaln        :  Display IMA link status
  dspimaalmparm   :  Display IMA alaram integration times
  dspln           :  Display DS1 line
  dsplns          :  Display all DS1 lines
  dsploads        :  Display the total bandwidth used up in each port
  dspplpp         :  Display the PLPP configuration of each line
  dspport         :  Display the configured ATM/IMA port
  dspportcnt      :  Display Port Counters
  dspportq        :  Display the egress queue configuration
  dspportqs       :  Display configuration of all egress queues
  dspports        :  Display the configured ATM/IMA ports
  dspsarcnt       :  Display the SAR counters of a connection
  dspsarcnts      :  Display the SAR counters of all connections
  dspslftst       :  Display self test configuration
  dspslftsttbl    :  Display the self test results
  dspsttatparms   :  Display the statistics params configured
  dspsvcrange     :  Display the resource partition between PVCs & SVCs
  dsptotals       :  Display the total connections configured per port
  runslftstno     :  Run a particular self test
 
 
Type <CR> to continue, Q<CR> to stop:
 
  tstcon          :  Test the connection towards the N/W side
  tstconseg       :  Test the connection towards the CPE side
  tstconsti       :  Test the connection towards the N/W side using STI supervil
  tstdelay        :  Measure the delay towards the N/W side
  tstdelaysti     :  Measure the delay towards the N/W side using STI supervisol
  upport          :  Up an ATM port
  xcnfalm         :  Configure alms of a DS1 line
  xcnfln          :  Configure a DS1 line
  
spirit3.1.10.AUSMB8.a >
 
 

where

slot number

is the card slot.

Related Commands

none

Cards on Which This Command Executes

PXM, FRSM, AUSM, CESM, VISM

Attributes

Log: Yes State: Any state Privilege: Any

Example

node1.1.22.AUSM8.a > cc 8

Description

Switch from the AUSM in slot 22 to the PXM in slot 8.

System Response

 
 
(session redirected)
 
node1.1.8.PXM.a >
 

where:

aimux_grp

AIMUX group number in the range 1-8.

Related Commands

delaimgrpcnt

Cards on Which This Command Executes

AUSM

Attributes

Log: Yes State: Active Privilege: 1-2

Example

node1.1.22.AUSM8.a > clraimgrpcnt 8

Description

Clear all the AIM group counters in AIM group 8.

System Response

none

where:

aimux_grp

AIMUX group number in the range 1-8

Related Commands

dspaimlncnt, clrimalncnt

Cards on Which This Command Executes

AUSM

Attributes

Log: No State: Active Privilege: 1

Example

node1.1.22.AUSM8.a > clraimlncnt 8

Description

Clear all the AIM line counters in AIM group 8.

System Response

none

where:

-ds3 LineNum

LineNum is in the format slot.port, where slot is either 7, 15, or 31 and port is a value in the range 1-n, where n is the highest numbered port on the card.

or

clralm -e3 <LineNum>

where:

-e3 LineNum

LineNum is in the format slot.port, where slot is either 7, 15, or 31 and port is a value in the range 1-n, where n is the highest numbered port on the card.

or

clralm -sonet <LineNum>

where:

-sonet LineNum

LineNum is in the format slot.port, where slot must be 7, and port is a value in the range 1-n, where n is the highest numbered port on the card.

or

clralm -plcp <PLCPNUM>

-plcp PLCPNUM

PLCPNum = 1-n, where n is the highest number line on the card.

For an FRSM, VISM, AUSM, or CESM:

clralm -ds1 <LineNum>

where:

LineNum

LineNum = 1-n, where n is the highest number line on the card.

For an SRM-3T3:

clralm <-srmds3> <LineNum>

where:

LineNum

LineNum = 1-n, where n = 3 if SRM-3T3

Related Commands

clralms, dspalm, dspalms

Cards on Which This Command Executes

PXM, FRSM, AUSM, CESM, VISM

Attributes

Log: No State: Any Privilege: 5-6

Example

node1.1.22.AUSM8.a > clralm -ds1 1

Description

Clear all the alarms caused by the collection of statistical data for line 1 on the current card.

System Response

none

where:

-ds3 LineNum

LineNum is in the format slot.port, where slot is either 7, 15, or 31 and port is a value in the range 1-n, where n is the highest numbered port on the card.

or

clralmcnt -e3 <LineNum>

where:

-e3 LineNum

LineNum is in the format slot.port, where slot is either 7, 15, or 31 and port is a value in the range 1-n, where n is the highest numbered port on the card.

or

clralmcnt -sonet <LineNum>

where:

-sonet LineNum

LineNum is in the format slot.port, where slot must be 7, and port is a value in the range 1-n, where n is the highest numbered port on the card.

or

clralmcnt -plcp <PLCPNUM>

where:

-plcp PLCPNUM

PLCPNum = 1-n, where n is the highest number line on the card.

For an FRSM, VISM, AUSM, or CESM:

clralmcnt -ds1 <LineNum>

where:

LineNum

LineNum = 1-n, where n is the highest number line on the card.

Related Commands

dspalmcnt, clralmcnts

Cards on Which This Command Executes

PXM, FRSM, AUSM, CESM, VISM

Attributes

Log: No State: Any Privilege: Any (5 on PXM)

Example

node1.1.22.AUSM8.a > clralmcnt -ds1 1

Description

Clear all the alarm counters and statistics collected for line 1 on the current card.

System Response

none

Related Commands

dspalmcnt, clralmcnt

Cards on Which This Command Executes

FRSM, AUSM, CESM, VISM

Attributes

Log: No State: Any Privilege: 1-5

Example

node1.1.22.AUSM8.a > clralmcnts

Description

Clear all the alarm counters and statistics collected for the current card.

System Response

none

Related Commands

dspcderrs

Cards on Which This Command Executes

FRSM, AUSM

Attributes

Log: No State: Any Privilege: SuperUser

Example

node1.1.4.FRSM.a > clrcderrs

Description

Clear all the card-related errors on the FRSM in slot 4.

System Response

none

where:

channel number

A number in the range: · For FRSM-8T1/E1, 16-1015 · For FRSM-T3/E3/HS2, 16-2015 · For FRSM-2CT3, 16-4015 · For PXM, 16-4111 · For AUSM, 16-1015 · For CESM-8T1/E1, 32-279 · For CESM-T3/E3, one connection starting at 32

Related Commands

dspchan, clrchancnts, dspchancnt

Cards on Which This Command Executes

PXM, FRSM, AUSM, CESM

Attributes

Log: Yes State: Any Privilege: Any

Example

node1.1.4.FRSM.a > clrchancnt 16

Description

Clear all the channel counters for channel 16 on the FRSM in slot 4.

System Response

none

The frame relay counters for each channel are:

• Received frames

• Received bytes

• Received frames DE

• Received bytes DE

• Received frames discarded

• Received bytes discarded

• Received frames discarded for shelf alarms

• Received frames discarded for exceeded queue depth

• Received bytes discarded for exceeded queue depth

• Received frames discarded for exceeded DE threshold

• Received frames FECN

• Received frames BECN

• Received frames tagged FECN

• Received frames tagged BECN

• Received frames tagged DE

• Transmitted frames

• Transmitted bytes

• Transmitted frames BECN

• Transmitted frames FECN

• Transmitted frames DE

• Transmitted bytes DE

• Transmitted frames discarded

• Transmitted bytes discarded

• Transmitted frames discarded for exceeded queue depth

• Transmitted bytes discarded for exceeded queue depth

• Transmitted frames discarded for exceeded DE threshold

• Transmitted frames discarded for physical layer fail

• Transmitted frames discarded for CRC error

• Transmitted frames discarded for reassembly failure

• Transmitted frames discarded for source abort

• Transmitted frames during LMI logical port alarm

• Transmitted bytes during for LMI logical port alarm

• Transmitted frames tagged FECN

• Transmitted frames tagged BECN

Related Commands

dspchan, clrchancnt, dspchancnt

Cards on Which This Command Executes

PXM, FRSM, AUSM, CESM

Attributes

Log: Yes State: Any Privilege: 1-3 (Any on PXM)

Example

node1.1.4.FRSM.a > clrchancnts

Description

Clear all the channel counters for all channels on the FRSM in slot 4.

System Response

none

where:

aimux_grp

AIMUX group number

Related Commands

dspaimlncnt, clraimlncnt

Cards on Which This Command Executes

AUSM

Attributes

Log: No State: Active Privilege: 1

Example

flyers01.1.17.AUSM.a > clrimalncnt 1

Description

Clear all the inverse multiplexing ATM line counters for IMA group 1 on the AUSM card in slot 17.

System Response

none

where:

-log	indicates that a specific log file number follows.
log slot	is the number in the event log file.

Related Commands

dsplog

Cards on Which This Command Executes

PXM

Attributes

Log: Yes State: Any Privilege: 1

Example

wilco.1.7.PXM.a > clrlog

Description

Clear all event log files on the PXM card.

System Response

none

Related Commands

dspmsgcnt

Cards on Which This Command Executes

FRSM, AUSM, CESM, VISM

Attributes

Log: No State: Any Privilege: 1-5

Example

flyers01.1.17.AUSM.a > clrmsgcnt 1

Description

Clear all the control message counters on the AUSM card in slot 17.

System Response

none

where:

On a PXM, port number is in the range 1-32.

On an AUSM, port number is in the range 1-8.

On an FRSM, port number is in the range 1-192 for T1, 1-248 for T1.

Related Commands

clrportcnts, dspportcnt

Cards on Which This Command Executes

PXM, FRSM, AUSM

Attributes

Log: No State: Any Privilege: 1-5 (Any on PXM)

Example

flyers01.1.17.AUSM.a > clrportcnt 1

Description

Clear all the port counters on port 1 on the AUSM card in slot 17.

System Response

none

Related Commands

clrportcnt, dspportcnt

Cards on Which This Command Executes

PXM, FRSM, AUSM

Attributes

Log: No State: Any Privilege: 1-5

Example

flyers01.1.17.AUSM.a > clrportcnts

Description

Clear all the port counters on all the ports on the AUSM card in slot 17.

System Response

none

Related Commands

dspsarcnt

Cards on Which This Command Executes

FRSM, AUSM, CESM, VISM

Attributes

Log: No State: Any Privilege: 1-5

Example

flyers01.1.17.AUSM.a > clrsarcnt

Description

Clear all the SAR counters on the AUSM card in slot 17.

System Response

none

Related Commands

none

Cards on Which This Command Executes

PXM, FRSM, AUSM, CESM, VISM

Attributes

Log: No State: Any Privilege: Any

Example

flyers01.1.17.AUSM.a > clrscrn

Description

Clear the screen.

System Response

flyers01.1.17.AUSM.a >