Table of Contents

PNNI-Specific Traps
Mandatory Trap Varbinds

Trap-Specific Varbinds

PNNI Traps

This chapter describes the traps specific to PNNI.

Contents of this chapter include:

• PNNI-Specific Traps

• Mandatory Trap Varbinds

PNNI-Specific Traps

Table 5-1 provides descriptions of the supported traps PNNI-specific traps.

Note   All mandatory trap varbinds are described inTable 5-2. For a description of each miscellaneous trap varbind, see Table 5-3.

Table 5-1: PNNI List of Traps

Name	Number	Specific-Varbinds	Description
ciscoWANSscopLinkChange	70003	ifIndex, cwspPhyIdentifier, cwspSscopStatus	Specifies if the Sscop link status is failed or established.
ciscoWANControllerStateChange	70004	cwspPnniControllerStatus, cwspPnniControllerPhySlot	Indicates the PNNI controller is active or standby.
ciscoWANIntfAddTrap	70005	ifIndex, cwspPhyIdentifier	Adds an interface.
ciscoWANIntfDeleteTrap	70006	ifIndex, cwspPhyIdentifier	Deletes an interface.
ciscoWANIntfConfigurtaion ChangeTrap	70007	ifIndex, cwspPhyIdentifier	Changes the configuration for an interface.
ciscoWANIntfOperationChange Trap	70008	ifIndex, cwspPhyIdentifier, cwspOperStatus, cwspOperIfcType, cwspOperFailReason	Changes the operation status for an interface.
ciscoWANSpvcFailTrap	70009	ifIndex, cwspConnTraceSrcVpi, cwspConnTraceSrcVci, cwspCallCallingAddress, ciscoWANSpvcFailReason	Indicates the Soft Permanent Virtual Connection (SPVC) failure that is recognized in the PNNI controller.
ciscoWANPnniControllerStndby Failed	70010	cwspPnniControllerPhySlot	Indicates the PNNI standby controller failed.
ciscoWANSpvcNodePrefix Change	70011	cwspSpvcNodePrefix	Specifies the PNNI controller can send this notification when the SPVC node prefix is changed. The cwspSpvcNodePrefix can contain the updated prefix.

Mandatory Trap Varbinds

Table 5-2 lists the trap variables (varbinds) in each trap generated by the switch. Each of these varbinds, in the order given, is available for each trap generated.

Table 5-2: Mandatory Trap Varbinds

Varbind	Data Type	Description
lastSequenceNumber	INTEGER	Contains the sequence number assigned to the trap. This can be used by Network Management System (NMS) applications to implement a Robust Trap Mechanism.
sysName	OctetString	Contains the node name of the switch.
entPhysicalContainedIn	INTEGER(0..2147483647)	Contains the chassis number into which the module is connected.
entPhysicalParentRelPos	INTEGER(-1..2147483647)	Contains the physical slot number to into which the module is connected.
entPhysicalVendorType	ObjectID	Contains the type of module for which the trap is generated.
moduleTrapAlarm Severity	INTEGER ( enumeration)	Contains the alarm severity of the trap.
genericTimeStamp	OctetString(1..30)	Contains the time when the trap is generated.

Trap-Specific Varbinds

Table 5-3 lists the trap-specific varbinds.

Note   These trap varbinds are not available for all the traps.

Table 5-3: PNNI Trap-Specific Varbinds

Varbind	Data Type	Description
ifIndex	Integer32(1..2147483647)	Specifies a unique value, greater than zero, for each interface. It is recommended that values are assigned starting with one.
ifName	OctetString(0..255)	Specifies the textual name of the interface.
cwspPhyIdentifier	OctetString(0..255)	Indicates the physical identification of the interface.
cwspSscopStatus	INTEGER	Specifies the Sscop link status on an Network-to-Network Interface (NNI).
cwspPnniControllerStatus	INTEGER (enum)	Specifies the administrative status of the PNNI controller.
cwspPnniControllerPhySlot	Integer32	Specifies the PNNI controller physical location.
cwspOperStatus	INTEGER	Specifies the operational state of the interface.
cwspOperIfcType	INTEGER	Specifies the interface type.
cwspOperFailReason	INTEGER	Defines the SVC port failures. Note   This object is used only for a trap varbind. NMS applications should not use issue SNMP get and get-next requests for this object.
cwspConnTraceSrcVpi	Integer32(0..4095)	Shows the VPI value of the starting point on this interface.
cwspConnTraceSrcVci	Integer32(0..65535)	Shows the VCI value of the starting point on this interface.
cwspCallCallingAddress	OctetString	Shows the calling party address of the call.
ciscoWANSpvcFailReason	INTEGER (enumeration)	Defines the SPVC manager failures. Note   This object is used only for a trap varbind. NMS applications should not depend on the impenmentation of this object. SNMP get and get-next requests are not valid for this object.
cwspSpvcNodePrefix	OctetString(13..13)	Specifies that write access is currently not permitted.

Posted: Fri Sep 15 11:18:54 PDT 2000
Copyright 1989-2000©Cisco Systems Inc.