Table of Contents

Traps and Alarms Supported

Traps and alarms are sent by the PXM45 card on various actions. Examples of these actions are adding, deleting, or modifying resources and line failures.

Table 3-1 describes the various PXM45 traps and alarms.

Table 3-1: PXM45 Traps and Alarms

Trap Name	Trap No.	Description
cwChassisIntegratedAlarm	60001	Sent when the integrated alarm for the shelf is changed.
cwUserLogin	60002	Sent when a user logs in.
cwUserLogout	60003	Sent when a user logs out.
cwShelfRestart	60004	Sent when the shelf is rebooted.
cwNodeNameChange	60006	Sent when the node name is modified.
cwIpAddressChange	60007	Sent when the IP Address (Ethernet IP, ATM IP) is modified.
cwControllerAdd	60008	Sent when a VSI Controller is added.
cwControllerDelete	60009	Sent when a VSI Controller is deleted.
cwChassisTemperatureNormal	60026	Sent when the temperature is back to normal.
cwChassisTemperatureAboveNormal	60027	Sent when the temperature is above the threshold.
cwChassisDclevelNormal	60028	Sent when the DC Level is back to normal.
cwChassisDclevelBelowNormal	60029	Sent when the DC level is below the normal range.
cwChassisPowersupplyNormal	60030	Sent when the power supply is back to normal voltage.
cwChassisPowersupplyFailed	60031	Sent when the power supply is failed.
cwChassisFanrpmNormal	60032	Sent when the fan rpm is back to normal.
cwChassisFanrpmBelowNormal	60033	Sent when the fan rpm is below the normal value.
cwModuleInserted	60051	Sent when the Front Module is plugged into a slot. This trap is sent for Processor Module as well as Service Modules.
cwModuleRemoved	60052	Sent when the Front Module is removed from the slot.This trap is sent for Processor Module and service modules.
cwModuleMismatch	60053	Sent when the Front Module is plugged into a slot which was configured with some other module earlier.
cwModuleActive	60055	Sent when a module becomes active. This may be a due to switch over or a failed card becomes active.
cwModuleStandby	60056	Sent when a module becomes standby due to switch over.
cwModuleFailed	60057	Sent when a module goes to a failed state.
cwLineModuleInserted	60058	Sent when a line module (back card ) is inserted.
cwLineModuleRemoved	60059	Sent when a line module (back card ) is removed.
cwLineModuleMismatch	60060	Sent when a incompatible line module ( back card ) is inserted into the front module or inserted line module is not same as the one configured earlier.
cwCoreCardSwitch	60078	Sent when there is a switch over for core card set.
cwRedundancyAdd	60079	Sent when a redundancy is added for a module pair
cwRedundancyDelete	60080	Sent when a module pair is deleted from the redundancy configuration.
cwRedundancyActivate	60081	Sent when a secondary module becomes active. This is due to switch over.
cwRedundancyRevert	60082	Sent when a primary module becomes active.This is due to switch over.
cwBulkFileCreationStarted	60901	Sent when the bulk file creation is started.
cwBulkFileCreationDone	60902	Sent when the bulk file creation is done.
cwBulkFileCreationAborted	60903	Sent when the bulk file creation is aborted.
cwBulkNoTaskAvailable	60904	Sent when the bulk file creation failed due to non availability of task.
cwBulkFileCreationFailed	60905	Sent when the bulk file creation is failed for reasons other than the non-availability of the task.

Posted: Fri Apr 14 19:50:46 PDT 2000
Copyright 1989 - 2000©Cisco Systems Inc.