Table of Contents

Abbreviations
Compatibility of Commands
add connection pl
add connection segpl
add system cescard
add system operator
add system switch
change cescard aps
change cescard config
change cescard image
change cescard linkinfo
change cescard redundancy
change cescard refclock
change cescard selfcheck
change connection pl
change connection segpl
change delaytest
change environment
change imccard config
change imccard image
change imccard redundancy
change logicalport atm
change physicalport ds1
change physicalport ds3
change physicalport oc3
change switch sntp
change system operator
change system switch
delete connection
delete system cescard
delete system operator
delete system switch
download
exit
show alarms detail
show alarms summary
show blademon information
show blademon statistics
show cescard aps detail
show cescard aps summary
show cescard config
show cescard info
show cescard linkinfo
show cescard redundancy
show cescard refclock config
show cescard refclock status
show cescard selfcheck
show cescard summary
show connection (all | pl |segpl) bertconfig
show connection (all | pl | segpl) bertstatus
show connection (all | pl | segpl) config
show connection (segpl | pl | all) statistics
show connection (all | segpl | pl) summary
show delaytest config
show delaytest status
show environment
show imccard config
show imccard info
show imccard redundancy
show logicalport atm config
show logicalport atm statistics
show logicalport atm summary
show physicalport ds0 allocation
show physicalport ds1 bertconfig
show physicalport ds1 bertstatus
show physicalport ds1 config
show physicalport ds1 statistics
show physicalport ds1 summary
show physicalport ds3 config
show physicalport ds3 statistics
show physicalport ds3 summary
show physicalport oc3 config
show physicalport oc3 statistics
show physicalport oc3 summary
show switch redundancy
show switch sntp config
show switch sntp status
show switch summary
show system operator
show system status
show system switch
show version

Command Reference

This chapter gives the complete command set for the VCLI. The chapter's two sections are

4. a table of commands, their optional abbreviations, and brief definitions

5. a complete command reference, with detailed explanations of commands, including attributes, options, and screen text.

Abbreviations

Table 2-1 shows the commands with optional abbreviations and brief descriptions. The commands are listed in alphabetical order within levels. For more information, see "Command Levels and Abbreviations" section.

Table 2-1: Command Abbreviation List

Command	Abbreviation	Description
add connection pl	a c pl	Adds a Private Line connection (local or remote).
add connection segpl	a c s	Adds a local Private Line segment between a DS1 interface and the ATM trunk.
add system cescard	a s c	Adds a CES card to the VCLI system.
add system operator	a s o	Adds an operator in the VCLI system.
add system switch	a s s	Adds a switch to the VCLI system.
change cescard aps	c ce a	Changes APS attributes for a CES card.
change cescard config	c ce c	Changes a CES card's configuration information.
change cescard image	c ce im	Changes the software image running on a CES card.
change cescard linkinfo	c ce l	Changes attributes of a CES card's uplink info.
change cescard redundancy	c ce red	Changes a CES card's redundancy configuration or behavior.
change cescard refclock	c ce ref	Changes the CES card's reference clock.
change cescard selfcheck	c ce s	Changes the backup CES card's health monitoring attributes.
change connection pl	c co pl	Changes the attributes of one endpoint of a Private Line connection.
change connection segpl	c co s	Changes the attributes of a local Private Line segment.
change delaytest	c d	Changes configuration of OAM network test.
change environment	c e	Changes environment variables.
change imccard config	c i c	Changes an IMC card's configuration (name, location, contact).
change imccard image	c i i	Changes the active software image running on an IMC card.
change imccard redundancy	c i r	Forces a switchover to the backup IMC card.
change logicalport atm	c l a	Changes the attributes of the ATM logical port.
change physicalport ds1	c p ds1	Changes the attributes of a DS1 physical port.
change physicalport ds3	c p ds3	Changes the attributes of a DS3 physical port.
change physicalport oc3	c p o	Changes the attributes of an OC3 physical port.
change switch sntp	ch s	Changes SNTP info of switch.
change system operator	c s o	Changes the privilege level for a VCLI operator account.
change system switch	c s s	Changes attributes of a switch.
delete connection	de c	Removes a connection from the system.
delete system cescard	de s c	Removes a CES card from the system.
delete system operator	de s o	Removes an operator from the VCLI system.
delete system switch	de s s	Removes a system switch from the system.
download	do	Downloads software image to a switch.
exit	e	Exits the VCLI program.
reboot	r	Reboots a card or entire switch.
show alarms detail	sh a d	Shows details for every alarm on the system.
show alarms summary	sh a s	Shows which cards and switches have active alarms.
show blademon info	sh b i	Shows availability info for any card or for a whole switch.
show blademon statistics	sh b st	Shows background pollers' statistics for a card or all cards in a switch.
show cescard aps detail	sh ce a d	Shows APS information (configuration, status, statistics).
show cescard aps summary	sh ce a s	Shows the information about the SONET APS status of a CES card's OC3c trunk port.
show cescard config	sh ce c	Shows configuration information about CES card.
show cescard info	sh ce inf	Shows CES card type, software revision, part number, serial number, CLEI code, date of manufacture, and so on.
show cescard linkinfo	sh cs l	Shows CES card's linkinfo configuration (uplink number, uplink logical port).
show cescard redundancy	sh ce red	Shows CES card's redundancy configuration and status.
show cescard refclock config	sh ce ref c	Shows reference clocks' configuration.
show cescard refclock status	sh ce ref s	Shows current reference and state of all four timing sources.
show cescard selfcheck	sh ce se	Shows backup CES card's selfcheck status.
show cescard summary	sh ce s	Shows CES card's availability, redundancy role, upTime, and alarms.
show connection all | pl | segpl bertconfig	sh co bertc a | p | s	Shows BERT test configuration for all connections, a Private Line connection, or a Private Line Segment.
show connection all | pl | segpl bertstatus	sh co berts a | p | s	Shows BERT test statistics for all connections, a Private Line connection, or a Private Line Segment.
show connection all | pl | segpl config	sh co a |p| s c	Shows configuration for a Private Line or PL segment or segments.
show connection all | segpl | pl statistics	sh co a |p| s st	Shows statistics for one end of a Private Line or Private Line segment.
show connection all | segpl | pl summary	sh co a |p| s su	Shows connection status and information for a pl or segpl. Also shows endpoint 2 identifiers for pl.
show delaytest configuration	sh d c	Shows delaytest configuration.
show delaytest status	sh d s	Shows status for delaytest.
show environment	sh e	Shows the environment settings for the session.
show imccard config	sh i c	Shows IMC card's name, location, contact information, and switch IP address.
show imccard info	sh i i	Shows information about IMC card.
show imccard redundancy	sh i r	Shows IMC card's redundancy configuration and status.
show logicalport atm config	sh l a c	Shows logical port ATM configuration.
show logicalport atm statistics	sh l a st	Shows logical port ATM statistics.
show logicalport atm summary	sh l a su	Shows information about ATM logical port, such as administrative status.
show physicalport ds0 allocation	sh p ds0 a	Shows how the DS0 timeslots within a DS1 are allocated to CES connections.
show physicalport ds1 bertconfig	sh p ds1 bertc	Shows DS1 BERT configuration.
show physicalport ds1 bertstatus	sh p ds1 berts	Shows DS1 BERT statistics.
show physicalport ds1 config	sh p ds1 c	Shows the configuration information for the DS1 port.
show physicalport ds1 statistics	sh p ds1 st	Shows the statistics for the DS1 port.
show physicalport ds1 summary	sh p ds1 su	Shows the summary of status for DS1 port.
show physicalport ds3 config	sh p ds3 c	Shows the configuration information for the DS3 port.
show physicalport ds3 statistics	sh p ds3 st	Shows the statistics for the DS3 port.
show physicalport ds3 summary	sh p ds3 su	Shows the summary of status for DS3 port status.
show physicalport oc3 config	sh p o c	Shows the configuration information for the OC3 port.
show physicalport oc3 statistics	sh p o st	Shows the statistics for the OC3 port.
show physicalport oc3 summary	sh p o su	Shows the summary of status for OC3 port.
show switch redundancy	sh sw r	Shows all redundancy groups within a switch, and role and status of each card.
show switch sntp config	sh s sn c	Shows sntp configuration (IP addresses, admin status, operating mode, and so on).
show switch sntp status	sh s sn s	Shows sntp status (timing, delay, clock offset, and so on).
show switch summary	sh s su	Shows summary for cards in switch.
show system operator	sh sy o	Shows information about all operators in the system.
show system status	sh sy st	Shows the status of the in-band and out-of-band interfaces that the VCLI string is using.
show system switch	sh sy sw	Shows the configuration information for a switch or all switches.
show version	sh v	Shows VCLI release number.

Compatibility of Commands

Most VCLI commands are backwards-compatible with all earlier releases of the VCLI. However, the following commands will not work with Release 2.2 or earlier:

add system cescard

add connection pl

change physicalport ds1

change physicalport ds3

show blademon info (for cescards only)

show physicalport ds3 config

add connection pl

Purpose

Adds a Private Line connection. The connection can be a local (within the same card) connection, or remote (on different cards) connection. The following characteristics of a private line connection can be set:

• DS1 port to terminate connection on

• DS0s to use [required if NxDS0 w/N < 24]

• Endpoint 2 DS1 port

• Endpoint 2 DS0s to use [required if NxDS0 w/N < 24]

• Admin Status (3 values---up, down, test)

• Signaling Mode (2 values---None, Robbed Bit Signaling)

• Partial Fill (integer 20 to 47, 0 for no partial fill)

• Reassembly CDVT (integer 4 to 140)

• Max Resassembly buffer size factor (integer 20 to 40)

• CGA Mode (3 values---voice nontransparent, voice transparent, dataport transparent)

• On-hook Robbed Bit Signaling towards endpoint 1 service interface (integer 0 to 15)

• Off-hook Robbed Bit Signaling towards endpoint 1 service interface (integer 0 to 15)

• On-hook Robbed Bit Signaling towards endpoint 2 service interface (integer 0 to 15)

• Off-hook Robbed Bit Signaling towards endpoint 2 service interface (integer 0 to 15)

• Unique Circuit ID Other non-unique identifiers (string and number)

• 9 different TCA thresholds (integers)

• ATM VPI (applies to remote connections only) [optional - can be autogenerated] (integer 0 to 2^VPI Bits-1) - VPI bits currently 2 -> 0 to 3

• ATM VCI (applies to remote connections only) [optional - can be autogenerated] (integer 0 to 2^VCI Bits) - VCI bits currently 12 -> 0 to 4095

• Loss of Cell Alarm enable/disable

Usage

For the user to add a remote connection, the following states must exist:

• ATM Network Provisioning Server has been configured and is reachable.

• Both cards (local and remote) have uplink port information configured.

This command will not work with Release 2.2 or earlier.

Options

-sname SwitchName	Name of switch endpoint 1 of the connection being added.
-card CardNum	Number of the card (2 to 16) endpoint 1 of the connection being added.
-ds3 DS3Num	Number of the DS3 port containing the DS1 endpoint 1 of the connection being added.
-ds1 DS1Num	Number of the DS1 port endpoint 1 of the connection being added.
-ds0 DS0s	List of DS0 timeslots (1 to 24) to terminate endpoint 1 of the connection on the DS1 interfaces of the connections. For example: (1,3,6 to 10). Default = (1 to 24).
-e2sname SwitchName	Name of switch endpoint 2 of the connection being added. Defaults to same value as -sname.
-e2card CardNum	Number of the card (2 to 16) endpoint 2 of the connection being added. Defaults to same values as -card.
-e2ds3 DS3Num	Number of the DS3 port containing the DS1 endpoint 2 of the connection being added.
-e2ds1 DS1Num	Number of the DS1 port endpoint 2 of the connection being added.
-e2ds0 DS0s	List of DS0 timeslots (1 to 24) to terminate endpoint 2 of the connection. For example: (1,3,6 to 10). Default = (1 to 24).
-cktid CircuitIdString	64-character ASCII string identifying the connection. This ID must be unique within the network because it is also used to identify the ATM PVC.
-cname NameString	64-character ASCII string associated with the connection.
-cnum Value	32-bit integer associated with the connection.
-as up | down | test	Admin Status of connection. Default = up.
-sigmode none | robbed	Channel Associated Signaling mode. Must be none if DS1 is Clear Channel. Default = none.
-pf Integer	Partial cell fill (range 20 to 47, 0 for no partial fill). Only applies if DS1 is in Channelized mode. Default = 0.
-mrbf Integer	Maximum Reassembly Buffer size Factor (in tenths) (range 20 to 40). Default = 20.
-rcdvt Integer	Reassembly Cell Delay Variation Tolerance (in tenths of a millisecond) (range 4 to 140). Default = 30.
-cgamode vt | vn | dt	Carrier Group Alarm mode. Only applies if DS1 is in Channelized mode. vt = voice transparent, vn = voice non-transparent, dt = dataport transparent. This can only be set to vn when sigmode = robbed. This can only be set to vt or dt when sigmode = none. Default = vt.
-onhktc Integer	On-Hook Trunk Conditioning Robbed Bit Signaling bits sent out the endpoint 1 DS1 interface (range 0 to 15). A bit is LSB, D bit is MSB. This only applies when cgamode = vn. Default = 0.
-offhktc Integer	Off-Hook Trunk Conditioning Robbed Bit Signaling bits sent out the endpoint 1 DS1 interface (range 0 to 15). A bit is LSB, D bit is MSB. This applies only when cgamode = vn. Default = 3.
-e2onhktc Integer	On-Hook Trunk Conditioning Robbed Bit Signaling bits sent out the endpoint 2 DS1 interface (range 0 to 15). A bit is LSB, D bit is MSB. This applies only when cgamode = vn. Default = 0.
-e2offhktc Integer	Off-Hook Trunk Conditioning Robbed Bit Signaling bits sent out the endpoint 2 DS1 interface (range 0 to 15). A bit is LSB, D bit is MSB. This applies only when cgamode = vn. Default = 3.
-vpi Value	VPI for ATM VCC on endpoint 1 card's trunk port (only if remote connection). Default = autogenerated.
-vci Value	VCI for ATM VCC on endpoint 1 card's trunk port (only if remote connection). Default = autogenerated.
-e2vpi Value	VPI for ATM VCC on endpoint 2 card's trunk port (only if remote connection). Default = autogenerated.
-e2vci Value	VCI for ATM VCC on endpoint 2 card's trunk port (only if remote connection). Default = autogenerated.
-loc disable|enable	Disable or enable an alarm when a circuit goes into a Loss of Cell condition. Disable = 1. Enable = 2. Default = enabled.
-tche15 Value	Cells with Header Errors 15-minute TCA threshold setting value.
-tche24 Value	Cells with Header Errors 24-hour TCA threshold setting value.
-tpr15 Value	Pointer Reframes 15-minute TCA threshold setting value.
-tpr24 Value	Pointer Reframes 24-hour TCA threshold setting value.
-tppe15 Value	Pointer Parity Errors 15-minute TCA threshold setting value.
-tppe24 Value	Pointer Parity Errors 24-hour TCA threshold setting value.
-tse15 Value	Sequence Errors 15-minute TCA threshold setting value.
-tse24 Value	Sequence Errors 24-hour TCA threshold setting value.
-tlc15 Value	Lost Cells 15-minute TCA threshold setting value.
-tlc24 Value	Lost Cells 24-hour TCA threshold setting value.
-tmc15 Value	Misinserted Cells 15-minute TCA threshold setting value.
-tmc24 Value	Misinserted Cells 24-hour TCA threshold setting value.
-tbu15 Value	Buffer Underflows 15-minute TCA threshold setting value.
-tbu24 Value	Buffer Underflows 24-hour TCA threshold setting value.
-tbo15 Value	Buffer Overflows 15-minute TCA threshold setting value.
-tbo24 Value	Buffer Overflows 24-hour TCA threshold setting value.
-tdc15 Value	Dropped Cells 15-minute TCA threshold setting value.
-tdc24 Value	Dropped Cells 24-hour TCA threshold setting value.

Example

VCLI>>add connection pl -sname tulsa1 -card 3 -ds3 1 -ds1 5 -ds0 (1-6) 
-e2sname boston08 -e2card 5 -e2ds3 2 -e2ds1 13 -e2ds0 (7-12) -sigmode robbed 
-cgamode vn -cktid TU1315
Connection with endpoint 1 EPID = 279, endpoint 2 EPID = 362 created.

add connection segpl

Purpose

Adds a local (within a single card) Private Line segment between a DS1 interface and the ATM trunk. The following attributes of a private line segment can be set:

• DS1 port to terminate connection on

• DS0s to use if DS1 is configured for Channelized mode

• Admin Status (3 values---up, down, test)

• Signaling Mode (2 values--- None, Robbed Bit Signaling)

• Partial Fill (integer 20 to 47, or 0 for no partial fill)

• Reassembly CDVT (integer 4 to 140)

• Max reassembly buffer size factor (integer 20 to 40)

• CGA Mode (3 values---voice nontransparent, voice transparent, dataport transparent)

• On-hook Robbed Bit Signaling towards service interface (integer 0 to 15)

• Off-hook Robbed Bit Signaling towards service interface (integer 0 to 15)

• On-hook Robbed Bit Signaling towards ATM interface (integer 0 to 15)

• Off-hook Robbed Bit Signaling towards ATM interface (integer 0 to 15)

• Unique Circuit ID

• Other non-unique identifiers (string and number)

• 9 different TCA thresholds

• ATM VPI [optional - can be autogenerated]

• (integer 0 to 2^{VPI Bits}-1) - VPI bits currently 2 -> 0 to 3

• ATM VCI [optional - can be autogenerated]

• (integer 0 to 2^{VCI Bits}) - VCI bits currently 12 -> 0 to 4095

• Loss of Cell Alarm enable/disable

Options

-sname SwitchName	Name of switch the connection will be added to.
-card CardNum	Number of the card (2 to 16) the connection will be added to.
-ds3 DS3Num	Number of the DS3 port containing the DS1 the connection will be added to.
-ds1 DS1Num	Number of the DS1 port the connection will be added to.
-ds0 DS0s	List of DS0 timeslots (1 to 24) to terminate the connection on the DS1 interface of the PL segment. For example (1,3,6 to 10). Default = (1 to 24).
-cktid CircuitIdString	64-character ASCII string identifying the connection. This ID must be unique within the network because it is also used to identify the Ascent ATM PVC.
-cname NameString	64-character ASCII string associated with the connection.
-cnum Value	32-bit integer associated with the connection.
-as up | down | test	Admin Status of connection. Default = up.
-sigmode none | robbed	Channel Associated Signaling mode. Must be none if DS1 is Clear Channel. Default = none.
-pf Integer	Partial cell fill (range 20 to 47, 0 for no partial fill). Only applies if DS1 is in Channelized mode. Default = 0.
-mrbf Integer	Maximum Reassembly Buffer size Factor (in tenths) (range 20 to 40). Default = 20.
-rcdvt Integer	Reassembly Cell Delay Variation Tolerance (in tenths of a millisecond) (range 4 to 140). Default = 30.
-cgamode vt | vn | dt	Carrier Group Alarm mode. Only applies if DS1 is in Channelized mode. vt = voice transparent, vn = voice non-transparent, dt = dataport transparent. This can only be set to "vn" when sigmode = robbed. For "vt" or "dt," the sigmode must be set to none. Default = vt.
-onhktc Integer	On-Hook Trunk Conditioning Robbed Bit Signaling bits sent out the DS1 interface (range 0 to 15). A bit is LSB, D bit is MSB. This only applies when cgamode = vn. Default = 0.
-offhktc Integer	Off-Hook Trunk Conditioning Robbed Bit Signaling bits sent out the CES interface (range 0 to 15). A bit is LSB, D bit is MSB. This only applies when cgamode = vn. Default = 3.
-e2onhktc Integer	On-Hook Trunk Conditioning Robbed Bit Signaling bits sent out the ATM interface (range 0 to 15). A bit is LSB, D bit is MSB. This only applies when cgamode = vn. Default = 0.
-e2offhktc Integer	Off-Hook Trunk Conditioning Robbed Bit Signaling bits sent out the ATM interface (range 0 to 15). A bit is LSB, D bit is MSB. This only applies when cgamode = vn. Default = 3.
-vpi	VPI for ATM VCC. Default = autogenerated.
-vci	VCI for ATM VCC. Default = autogenerated.
-loc disable|enable	Disable or enable an alarm when a circuit goes into a Loss of Cell condition. Disable = 1. Enable = 2. Default = enabled.
-tche15 Value	Cells with Header Errors 15-minute TCA threshold setting value.
-tche24 Value	Cells with Header Errors 24-hour TCA threshold setting value.
-tpr15 Value	Pointer Reframes 15-minute TCA threshold setting value.
-tpr24 Value	Pointer Reframes 24-hour TCA threshold setting value.
-tppe15 Value	Pointer Parity Errors 15-minute TCA threshold setting value.
-tppe24 Value	Pointer Parity Errors 24-hour TCA threshold setting value.
-tse15 Value	Sequence Errors 15-minute TCA threshold setting value.
-tse24 Value	Sequence Errors 24-hour TCA threshold setting value.
-tlc15 Value	Lost Cells 15-minute TCA threshold setting value.
-tlc24 Value	Lost Cells 24-hour TCA threshold setting value.
-tmc15 Value	Misinserted Cells 15-minute TCA threshold setting value.
-tmc24 Value	Misinserted Cells 24-hour TCA threshold setting value.
-tbu15 Value	Buffer Underflows 15-minute TCA threshold setting value.
-tbu24 Value	Buffer Underflows 24-hour TCA threshold setting value.
-tbo15 Value	Buffer Overflows 15-minute TCA threshold setting value.
-tbo24 Value	Buffer Overflows 24-hour TCA threshold setting value.
-tdc15 Value	Dropped Cells 15-minute TCA threshold setting value.
-tdc24 Value	Dropped Cells 24-hour TCA threshold setting value.

Example

VCLI>>add conn segpl -sname tulsa1 -card 3 -ds3 1 -ds1 5 -ds0 (1-6) -sigmode robbed -cgamode vn -cktid TU1315
Connection with EPID = 279 created.

add system cescard

Purpose

Adds a CES card (residing within a switch) to the VCLI system, using the following information:

• Card Number (2 to 16).

• IP Address ---in decimal dot notation (for example, 209.50.172.45) [optional] ---needed only if the autogenerated in-band IP address was overridden on the card.

• ATM switch uplink logical port identifier (for example, switch.100.101.102.103.card.6.pport.4.lport.2) [optional]. If not supplied, remote Private Line connections will require manual configuration of the intermediate ATM PVC.

• Uplink logical port integer identifier.

Usage

Command will not work with Release 2.2 or earlier.

Options

-sname SwitchName	Name of switch to add this card to
-card CardNumber	Slot number of card to add
-ipaddr IPAddress	In-band management IP address
-uplinklp logPortId	Logical port identifier of connected ATM switch port
-uplinknum logPortNumber	Logical port integer identifier

Example

VCLI>>add sys cescard -sname tulsa1 -card 2 -ipaddr 192.63.145.18 -uplinklp switch.100.101.102.103.card.6.pport.4.lport.2

add system operator

Purpose

Adds an operator to the VCLI system. The following information can be set:

• Operator Name

• Privilege Level (3 values---admin, change, show)

Usage

Command requires admin privilege level.

Options

-name OperatorName	Name of the operator to add
-priv admin | change | show	Privilege Level

Example

VCLI>>add system operator -name jdsmith -priv change

Note For many commands, such as the one above, if the command executes successfully, there will be no display other than the prompt and command, shown above.

add system switch

Purpose

Adds a switch to the VCLI system. This associates a switch name with its out-of-band (ethernet) IP address. The following information about the switch can be changed:

• Switch Name---Identifies the switch in all commands with the switch name identifier -sname. Can only be alphanumeric and underscore characters; length limit is 64 characters.

• Out-of-band IP Address using decimal dot notation (for example, 206.14.150.201).

• SNMP Community String for reading and writing to the switch.

• Chassis ID number---Assigned at the factory. Can be read from the barcode sticker under the power input on the back of the chassis.

Usage

Command requires admin privilege level.

Options

-sname SwitchName	Name of the switch to add
-ipaddr IPAddress	Out-of-band management IP address
-community String	ASCII string to be used as the SNMP community string in all Set and Get SNMP PDUs sent to the cards in this switch
-chassisid ChassisID	Integer number indicated on the back of the chassis
-ftppass password	Password for downloading software images; use up to 8 characters

Example

VCLI>>add sys switch -sname tulsa1 -ipaddr 206.14.150.201 -community borg19e -chassisid 23

change cescard aps

Purpose

Changes SONET Automatic Protection Switching (APS) attributes for a CES card. The following information about the card can be changed:

• Administrative Status (2 values---enabled, disabled)

• Directional Mode (2 values---unidirectional, bidirectional)

• BER Threshold (6 values---10^-4, 10^-5, 10^-6, 10^-7, 10^-8, 10^-9)

• Commands (6 values---clear, lockout, forced switch to protection, forced switch to working, manual switch to protection, manual switch to working)

Options

-sname SwitchName	Name of switch to change card APS for.
-card CardNum	Number of the card (2 to 16) to change APS for.
- side access | trunk	User specifies where to change APS on TDM access or ATM Trunk. Only applies to CS3 blades with 4 OC3 ports.
-as enabled | disabled	Administrative status of APS function.
-dir unidir | bidir	Directional mode. Can be modified only when APS is disabled.
-berthresh minus4 | minus5 | minus6 |minus7 | minus8 | minus9	Exponent of 10 of Bit Error Rate threshold for switching. Can be modified only when APS is disabled.
-cmd clear | lock | force2prot |force2work | man2prot | man2work	APS control command. Clears any existing command (normal case).
-lock	Lockout all protection switching.
-force2prot	Forces switchout of working line to protection.
- force2work	Forces switchout of protection line to working (only for 1+1 per spec).
-man2prot	Causes switchout of working line to protection if no higher priority request is in effect.
-man2work	Causes switchout of protection line to working if no higher priority request is in effect (only for 1+1 per spec).

If `-side' argID is specified on a CES card that supports only trunk side OC3 interfaces, this option is to be ignored.

Example

VCLI>>change cescard aps -sname tulsa1 -card 3 -as enabled

Note If the componentType attribute of the CES card is CS3 blade type (value=29) and the componentType of the I/O card is 4OC3 ports (value=28), this card is capable of supporting APS on both the access and trunk side. The user must specify which side in this case. If neither of the ComponentType values described above is true, APS is supported on the trunk side only.

Note The side (access side or trunk side) determines what the index into the APS MIB tables will be. The trunk side uses an index of 0. Access uses an index of 1.

change cescard config

Purpose

Changes the card's configuration information, as follows:

• Name string

• Location string

• Contact information string

• Fan monitoring

Options

-sname SwitchName	Name of switch to change card config for
-card CardNum	Number of the card (2 to 16) to change config for
-name NameString	Identifier string for the card
-location LocationString	Location string for the card
-contact ContactString	Contact string for the card
-fanmon ena | dis	Controls fan tray monitoring

Example

VCLI>>change cescard config -sname tulsa1 -card 2 -name Tulsa1_card2 -fanman ena

change cescard image

Purpose

Changes the software image running on a card.

Options

-network 1	Changes all known cards in the network.
-sname SwitchName	Name of containing switch to change card config for.
-card CardNum	Number of the logical card (may not be actual card in some redundancy).
-physcard CardNum	Number of the actual card (overrides redundancy status).
-noconfirm1	Execute this command without prompting user for confirmation.
-swcmd command	Optional command to allow the user to force the behavior of the switch during download.
-wait yes/no	Setting this allows user to wait for the completion of the command. values---yes=1, no=2, default = yes.

Example

VCLI>>change cescard image -sname tulsal -card 3 -swcmmd 2
Are you sure [NO]?
 
Switch Name: Tulsa
Command sent to switch tulsa card(s) 3
Update in progress...
.....................
Card 3 successful
 

The argId -physcard tells the VCLI to communicate with the CPE card located in physical slot 3. This bypasses the logic that will be in effect should the primary CPE card be switched out. Using the -card option will not bypass VCLI redundancy logic, and if the CPE card in slot 3 is switched out, the VCLI will communicate with the switched in backup.

If the -swcmd option is not specified, the VCLI will use the contents file in the relevant image directory to find the line with the swdwnld command and use its value. This line is usually the very first non-comment line in the contents file.

This command shows the progress of the upgrade/downgrade procedure on the CES card. The VCLI shows if the upgrade/downgrade was successful as reported by the CES card. This way, users are alerted to an upgrade/downgrade failure and can take action.

change cescard linkinfo

Purpose

Changes the following attributes of a CES card's uplink information:

• Uplink string

• Uplink number

Options

-sname SwitchName	Name of switch to change inband management for
-card CardNum	Number of the card (2 to 16) to change inband management for
-uplinklp	Logical port identifier of connected ATM switch port
uplinknum	Logical port integer identifier

Example

VCLI>>change cescard linkinfo -sname tulsa1 -card 3 -uplinklp
switch_ip.172.29.59.172.card.3.pport.3.lport.3 -uplinknum 3

change cescard redundancy

Purpose

Changes a CES card's redundancy configuration or behavior.

Note Actions depend on whether the card is a primary, backup, or neither.

The following action can be performed on a card that is not a member of a redundancy group (that is, the card's role must be none [or neither]):

• Change redundancy role---Card can be made a backup for a redundancy group. A card cannot be made a backup if there are already any primary cards in a higher slot number that are a member of lower slot numbered backup's group. Card can be made a primary member of a redundancy group. A card cannot be made a primary if there is no backup card with a lower slot number.

The following actions can be performed for a card that is a backup:

• Change redundancy role to none (only if there are no primary cards in this backup's group).

• Force a switch-over for a primary card in this backup's redundancy group (only if not already switched-in for a primary card)

• Force a switch-back for the primary card that this backup is currently switched-in for (only if the primary card is not failed)

The following action can be performed for a card that is a primary in a redundancy group:

• Change redundancy role to none, thus removing the card from the redundancy group. This can be done whether or not the primary card has failed.

Options

Only one of the attributes "role" or "force" may be used in a single command.

.

-sname SwitchName	Name of containing switch to change card redundancy for.
-card CardNum	Number of the card (2 to 16) to change redundancy for.
-role prim | back | none	Redundancy role of the card.
-force over	Force backup to switch in for the card specified by -card.
-force back	Force the backup card (indicated by -card) to switch the primary that it is currently protecting back into service.
-override ena	Force redundancy command to be set regardless of the state of the target cards.

Example

To create a redundancy group with two primaries in it:

VCLI>>change cescard redundancy -sname tulsa1 -card 2 -role back
VCLI>>change cescard redundancy -card 3 -role prim
VCLI>>change cescard redundancy -card 4 -role prim
 

To force backup to switch in for card 4:

VCLI>>change cescard redundancy -sname tulsa1 -card 4 -force over
 

To force backup to switch the primary it is currently switched in for back:

VCLI>>change cescard redundancy -sname tulsa1 -card 2 -force back
 

To remove a redundancy group with two primaries in it:

VCLI>>change cescard redundancy -sname tulsa1 -card 3 -role none
VCLI>>change cescard redundancy -card 4 -role none
VCLI>>change cescard redundancy -card 2 -role none

change cescard refclock

Purpose

Changes the CES card's reference clock, including the following:

• Primary Timing Reference (5 values---none, BITS A, BITS B, OC3 1, OC3 2)

• Secondary Timing Reference (5 values---none, BITS A, BITS B, OC3 1, OC3 2)

• Revertive Switching (2 values---disabled, enabled)

• Force Free Run (2 values---off, on)

• Switch To (2 values---primary, secondary)

Options

-sname SwitchName	Name of containing switch to change card refclock for
-card CardNum	Number of the card (2 to 16) to change refclock for
-prim bitsa | bitsb | oc31 | oc32 | none	New primary timing source (optional)
-second bitsa | bitsb | oc31 | oc32 | none	New secondary timing source (optional)
-revert disable | enable	New value for revertive switching (optional)
-forcefr off | on	New value for forcing timing to free run (optional)
-swto prim | second	Controls switching to a different timing reference (optional)

Example

VCLI>>change cescard refclock -sname tulsa1 -card 3 -second oc31 -revert enable

change cescard selfcheck

Purpose

Changes the following attributes of the backup card's health monitoring:

• Test period

• Hour

Note If test period control is set to once a day, the user can set the hour when selfcheck will begin.

Usage

Command is valid only for CES cards with redundancy role set to backup, and redundancy state set to standby.

Options

-sname SwitchName	Name of switch to change healthmonitor for.
-card CardNum	Number of card (2 to 16) to change healthmonitor for.
-period never|daily|hourly|minute|continuous	Never = 0; Daily = 1; Monthly = 2; Minute = 3; Continuous = 4. Default is Daily (1).
-hour HourValue	Hour when the selfcheck should begin. Values from 0 to 23 (0 = midnight, 1 = 1 a.m., and so on). Default: 0.

Example

VCLI>>change ces selfcheck -card 3 -sname tulsa1 -period continuous

change connection pl

Purpose

Changes the attributes of one endpoint of a Private Line segment, either local (within the same card) or remote (on different cards).

Note Nothing can be changed about the switch ATM PVC if it is a remote connection.

The following information about an endpoint can be changed:

• Admin Status (3 values---up, down, test)

• OAM Loopback Request (2 values---end-to-end, segment)---applies only to remote connections.

• Reassembly CDVT (integer 4 to 140)

• Max Resassembly buffer size factor (integer 20 to 40)

• CGA Mode (2 values---voice transparent, dataport transparent)

• On-hook Robbed Bit Signaling towards endpoint 1 service interface (integer 0 to 15)

• Off-hook Robbed Bit Signaling towards endpoint 1 service interface (integer 0 to 15)

• On-hook Robbed Bit Signaling towards endpoint 2 service interface (integer 0 to 15)

• Off-hook Robbed Bit Signaling towards endpoint 2 service interface (integer 0 to 15)

• Loss of Cell Alarm (2 values---disable, enable)

• 9 different TCA thresholds

• BERT parameters

Options

-sname SwitchName	Name of switch containing the connection.
-card CardNum	Number of the card (2 to 16) containing the connection.
-epid EndpointId	Endpoint identifier of the connection endpoint to be changed.
-as up | down | test	Admin Status of connection.
-oamlr end | segment	Type of ATM OAM loopback to request: end-to-end or segment. This only applies for remote PL's. Shows the results of this test using the show connection pl summary command.
-loop	Specifies the loopback mode for the connecting Values. 0 = none. 1 = out. 2 = in. This value applies only to change connection.
-mrbf Integer	Maximum Reassembly Buffer size Factor (in tenths) (range 20 to 40). Changing this parameter will cause temporary data loss on the connection.
-rcdvt Integer	Reassembly Cell Delay Variation Tolerance (in tenths of a millisecond) (range 4 to 140). Changing this parameter will cause temporary data loss on the connection.
-cgamode vt | dt	Carrier Group Alarm mode. This is only changeable when the containing DS1 is set for Channelized mode, and the sigmode = none for the connection.
-onhktc Integer	On-Hook Trunk Conditioning Robbed Bit Signaling bits sent out the DS1 interface (range 0 to 15). A bit is LSB, D bit is MSB. This is only changeable when cgamode = vn.
-offhktc Integer	Off-Hook Trunk Conditioning Robbed Bit Signaling bits sent out the DS1 interface (range 0 to 15). A bit is LSB, D bit is MSB. This is only changeable when cgamode = vn.
-e2onhktc Integer	On-Hook Trunk Conditioning Robbed Bit Signaling bits sent out the other endpoint's interface (range 0 to 15). A bit is LSB, D bit is MSB. This is only changeable when cgamode = vn.
-e2offhktc Integer	Off-Hook Trunk Conditioning Robbed Bit Signaling bits sent out the other endpoint's interface (range 0 to 15). A bit is LSB, D bit is MSB. This is only changeable when cgamode = vn.
-name NameString	64 character ASCII string associated with the connection.
-cnum Value	32 bit integer associated with the connection.
-loc disable|enable	Turns off the generation of an alarm went he circuit goes into Loss of Cell condition. Disable = 1. Enable = 2.
-tche15 Value	Cells with Header Errors 15-minute TCA threshold setting.
-tche24 Value	Cells with Header Errors 24-hour TCA threshold setting.
-tpr15 Value	Pointer Reframes 15-minute TCA threshold setting.
-tpr24 Value	Pointer Reframes 24-hour TCA threshold setting.
-tppe15 Value	Pointer Parity Errors 15-minute TCA threshold setting.
-tppe24 Value	Pointer Parity Errors 24-hour TCA threshold setting.
-tse15 Value	Sequence Errors 15-minute TCA threshold setting.
-tse24 Value	Sequence Errors 24-hour TCA threshold setting.
-tlc15 Value	Lost Cells 15-minute TCA threshold setting.
-tlc24 Value	Lost Cells 24-hour TCA threshold setting.
-tmc15 Value	Misinserted Cells 15-minute TCA threshold setting.
-tmc24 Value	Misinserted Cells 24-hour TCA threshold setting.
-tbu15 Value	Buffer Underflows 15-minute TCA threshold setting.
-tbu24 Value	Buffer Underflows 24-hour TCA threshold setting.
-tbo15 Value	Buffer Overflows 15-minute TCA threshold setting.
-tbo24 Value	Buffer Overflows 24-hour TCA threshold setting.
-tdc15 Value	Dropped Cells 15-minute TCA threshold setting.
-tdc24 Value	Dropped Cells 24-hour TCA threshold setting.
-bertdir tdm or atm	Direction to send the BERT pattern. Towards the access (tdm), or towards ATM network. Can't change while test is running
-bertpatt allones | 511 |2047 | qrss | 2^23-1| 3 in 24 | user	BERT pattern. Can't change while test is running
-userpatt hexPattern	User defined BERT pattern. A 32 bit pattern represented by an 8 character hexadecimal number. Can't change while test is running.
-userpattlen Value	User defined BERT pattern length. A number from 1 to 32. Can't change while test is running.
-txpattinv off | on	BERT transmit pattern bit inversion control. Can't change while test is running. Applies only when bertpatt is set to user.
-rxpattinv off | on	BERT receive pattern bit inversion control. Can't change while test is running. Applies only when bertpatt is set to user.
-bert on | off	Controls the running of the integrated BERT for this DS1.
-bertrestart no | yes	Restarts the running BERT test. Only applies when -bert on.
-1bitinsert no | yes	Inserts a single bit error into the transmitted BERT pattern. Only applies when -bert on.
-conterrinsert none | minus1 | minus2 | minus3 | minus4 | minus5 | minus6 | minus7	Continously inserts bit errors into the transmitted BERT pattern at a rate of 10 to the minus 1 through 7. Can be modified while the test is running.

Example

VCLI>>change conn pl -sname tulsa1 -card 3 -epid 283 -oamlr end

change connection segpl

Purpose

Changes the following attributes of a local Private Line segment:

• Admin Status (3 values---up, down, test)

• OAM Loopback Request (2 values---end-to-end, segment)

• Reassembly CDVT (integer 4 to 140)

• Max Resassembly buffer size factor (integer 20 to 40)

• CGA Mode (2 values---voice transparent, dataport transparent)

• On-hook Robbed Bit Signaling towards service interface (integer 0 to 15)

• Off-hook Robbed Bit Signaling towards service interface (integer 0 to 15)

• On-hook Robbed Bit Signaling towards ATM interface (integer 0 to 15)

• Off-hook Robbed Bit Signaling towards ATM interface (integer 0 to 15)

• Loss of Cell Alarm (2 values---disable, enable)

• 9 different TCA thresholds

• BERT parameters

Options

-sname SwitchName	Name of switch containing the connection.
-card CardNum	Number of the card (2 to 16) containing the connection.
-epid EndpointId	Endpoint identifier of the connection to be changed.
-oamlr end | segment	Type of ATM OAM loopback to request, end-to-end or segment. View the results of this test using the show connection segpl summary command.
-as up | down | test	Admin Status of connection.
-loop	Specifies the loopback mode for the connection. 0 = none. 1 = out. 2 = in. This option applies only to "change connection."
-mrbf Integer	Maximum Reassembly Buffer size Factor (in tenths) (range 20 to 40). Changing this parameter will cause temporary data loss on the connection.
-rcdvt Integer	Reassembly Cell Delay Variation Tolerance (in tenths of a millisecond) (range 4 to 140). Changing this parameter will cause temporary data loss on the connection.
-cgamode vt | dt	Carrier Group Alarm mode. This is only changeable when the containing DS1 is set for Channelized mode, and the sigmode = none for the connection.
-onhktc Integer	On-Hook Trunk Conditioning Robbed Bit Signaling bits sent out the DS1 interface (range 0 to 15). A bit is LSB, D bit is MSB. This is only changeable when cgamode = vn.
-offhktc Integer	Off-Hook Trunk Conditioning Robbed Bit Signaling bits sent out the DS1 interface (range 0 to 15. A bit is LSB, D bit is MSB. This is only changeable when cgamode = vn.
-e2onhktc Integer	On-Hook Trunk Conditioning Robbed Bit Signaling bits sent out the ATM interface (range 0 to 15). A bit is LSB, D bit is MSB. This is only changeable when cgamode = vn.
-e2offhktc Integer	Off-Hook Trunk Conditioning Robbed Bit Signaling bits sent out the ATM interface (range 0 to 15). A bit is LSB, D bit is MSB. This is only changeable when cgamode = vn.
-cname NameString	64 character ASCII string associated with the connection.
-cnum Value	32 bit integer associated with the connection.
-loc disable | enable	Turns off/on the generation of an alarm when the circuit goes in the Loss of Cell condition. Disable = 1. Enable = 2.
-tche15 Value	Cells with Header Errors 15-minute TCA threshold setting value.
-tche24 Value	Cells with Header Errors 24-hour TCA threshold setting value.
-tpr15 Value	Pointer Reframes 15-minute TCA threshold setting value.
-tpr24 Value	Pointer Reframes 24-hour TCA threshold setting value.
-tppe15 Value	Pointer Parity Errors 15-minute TCA threshold setting value.
-tppe24 Value	Pointer Parity Errors 24-hour TCA threshold setting value.
-tse15 Value	Sequence Errors 15-minute TCA threshold setting value.
-tse24 Value	Sequence Errors 24-hour TCA threshold setting value.
-tlc15 Value	Lost Cells 15-minute TCA threshold setting value.
-tlc24 Value	Lost Cells 24-hour TCA threshold setting value.
-tmc15 Value	Misinserted Cells 15-minute TCA threshold setting value.
-tmc24 Value	Misinserted Cells 24-hour TCA threshold setting value.
-tbu15 Value	Buffer Underflows 15-minute TCA threshold setting value.
-tbu24 Value	Buffer Underflows 24-hour TCA threshold setting value.
-tbo15 Value	Buffer Overflows 15-minute TCA threshold setting value.
-tbo24 Value	Buffer Overflows 24-hour TCA threshold setting value.
-tdc15 Value	Dropped Cells 15-minute TCA threshold setting value.
-tdc24 Value	Dropped Cells 24-hour TCA threshold setting value.
-bertdir tdm or atm	Direction to send the BERT pattern. Towards the access (tdm), or towards ATM network. Can't change while test is running.
-bertpatt allones | 511 |2047 | qrss | 2^23-1| 3 in 24 | user	BERT pattern. Can't change while test is running .
-userpatt hexPattern	User defined BERT pattern. A 32 bit pattern represented by an 8 character hexadecimal number. Can't change while test is running.
-userpattlen Value	User defined BERT pattern length. A number from 1 to 32. Can't change while test is running.
-txpattinv off | on	BERT transmit pattern bit inversion control. Can't change while test is running. Applies only when bertpatt is set to user.
-rxpattinv off | on	BERT receive pattern bit inversion control. Can't change while test is running. Applies only when bertpatt is set to user.
-bert on | off	Controls the running of the integrated BER test for this DS1.
-bertrestart no | yes	Restarts the running BERT test. Only applies when -bert on.
-1bitinsert no | yes	Inserts a single bit error into the transmitted BERT pattern. Only applies when -bert on.
-conterrinsert none | minus1 | minus2 | minus3 | minus4 | minus5 | minus6 | minus7 |	Continously inserts bit errors into the transmitted BERT pattern at a rate of 10 to the minus 1 through 7. Can be modified while the test is running.

Example

VCLI>>change conn segpl -sname tulsa1 -card 3 -epid 279 -oamlr end

change delaytest

Purpose

Changes configuration of OAM network test, including the following:

• Connection ID of the circuit to run the test on (integer 257 to 4096)

• Test state (enabled / disabled)

• Test duration given in seconds (integer 1 to 604800) max is 1 week

• Test number to run the test (integer 1 to 30)

Usage

OAM delay tests measure delay across the network using OAM loopback cells. Each card can run up to 30 simultaneous OAM delay tests.

Use this command to configure one of the tests, or to change the status of an ongoing test. Use of the -testnum argId is optional when configuring a new test. If the -testnum argId is not given, then the VCLI will use the first ATM OAM delay test that has a disabled state and has remaining test time of 0. If there is no test which has a state of disabled and remaining time of 0, VCLI will select the first test with state of disabled. If you wish to avoid having the VCLI pick the test number, then enter it on the command line using -testnum argId.

Options

-sname SwitchName	Name of switch containing the connection endpoint to be tested.
-card CardNum	Number of the card (2 to 16) containing the connection endpoint to be tested.
-epid EndpointId	Endpoint identifier of the connection endpoint to be tested.
-tstate disable/enable	State of the test. Disable = 0; Enable = 1.
-dur Integer	Test duration given in seconds. (1 to 604800) Max is 1 week.
-testnum Integer	Number which defines which of the available 30 tests to configure.

Example

VCLI>>change delaytest -sname tulsa1 -card 3 -epid 283 -tstate enable -dur 60

Note If the command executes successfully, there will be no display other than the prompt and command, shown above.

change environment

Purpose

Changes the following environment variables for the current login session:

• Autosave (enable or disable)---The Autosave feature is used to save the configuration into a card's non-volatile storage after every change command. This should be disabled if doing mass configuration using scripts. To manually save changes to non-volatile storage when the Autosave feature is disable, enter the save command.

• Timeout (time in minutes)---Controls how long before the VCLI program will automatically terminate when idle (no commands are issued). Setting the timeout value to zero will disable the timeout feature.

• Paging (page length in lines)---The paging feature causes the VCLI to output only a single page of output before giving the option to either "quit" (terminate the command), or output another page of information. Setting the paging value to 0 will disable the feature.

• ATMswitchpro (enable or disable)---This controls the automatic creation of ATM PVCs across the ATM network when a Private Line connection is added that has endpoints on two different CES cards.

• Provisioning Client CLI Directory---The directory to find the Provisioning Client CLI commands.

• SNMP Timeout (seconds)---The number of seconds the VCLI should wait for an SNMP response before deciding that an SNMP PDU was lost.

• Software Image (directory)---The directory to get the software image that will be downloaded to a switch. Defaults is $VCLI_DIR/image.

• Logging (loglevel)--- Log levels are from 0 to 4. 0 = disabled; 1 = add/delete commands logged; 4 = all commands logged including those that generate errors.

Options

-autosave ena | dis	Controls the autosave feature
-timeout Minutes	Idle time before session termination (0=never)
-paging Lines	Number of lines per page (0=no paging)
-atmswitchpro ena | dis	Controls PVC auto-provisioning
-provdir DirPath	Path to the Provisioning CLI directory
-snmptimeout Seconds	Number of seconds to wait for SNMP command completion
-imagedir DirPath	Path to the download image directory
-logging loglevel	Current level of loggin

Example

VCLI>>change environment -autosave ena -timeout 30 -paging 40

Note If the command executes successfully, there will be no display other than the prompt and command, shown above.

change imccard config

Purpose

Changes the following card configuration information:

• Name

• Location string

• Contact information string

Options

-sname SwitchName	Name of containing switch for which to change card config
-location LocationString	Location string for the card

Example

VCLI>>change imccard config -sname tulsa1 -name Tulsa1_IMC -location Tulsa_pop

change imccard image

Purpose

Changes the active software image running on the IMC card.

Options

-network	Changes all known cards in the network.
-sname SwitchName	Name of containing switch for which to change card config.
-swcmd command	Optional command to force the behavior of the switch during download.
-noconfirm 1	Execute this command without prompting user for confirmation.
-wait yes|no	Setting this allows user to wait for the completion of the command. values---yes = 1, no = 2. Default is yes.

Example

VCLI>>change imccard image -sname tulsa1 -swcmd 2
Are you sure [NO]?
Switch Name: tulsa
Command sent to switch tulsa card(s) 1
Update in progress..............................
Card 1 successful

If the -swcmd option is not specified, the VCLI will use the contents file in the relevant image directory to find the line with swdwnldCommand and use its value. This line is usually the very first non-comment line in the contents file.

This command will show the progress of the upgrade/downgrade procedure on the IMC card. The VCLI will show if the upgrade/downgrade was successful as reported by the IMC card. The intention is for the user to be alerted to a upgrade/downgrade failure and to act upon it.

change imccard redundancy

Purpose

Forces a switchover to the backup IMC card (if there is one).

Options

-sname SwitchName	Name of switch containing the imccard.
-force over	Force backup IMC card to switch in for the primary IMC card.

Example

VCLI>>change imccard redundancy -sname tulsa1 -force over
Are You Sure [No] ?

change logicalport atm

Purpose

Changes the following attributes of the ATM logical port:

• Admin Status (2 values---up, down)

• Identifier String

Options

-sname SwitchName	Name of switch containing the ATM BC
-card CardNum	Number of the card (2 to 16) containing the ATM BC
-as up | down	Admin Status ATM BC
-name NameString	Name string for ATM BC

Example

VCLI>>change logicalport atm -sname tulsa1 -card 3 -as down

change physicalport ds1

Purpose

Changes the following attributes of a DS1 port:

• Admin Status (3 values---up, down, test)

• Channelization Mode (Channelized, Clear Channel)

• Timing Mode (Internal, Through)

• Framing Mode (ESF, SF, Other)

• Facilities Data Link (2 values---none, T1.403)

• Bit-Oriented Send Code (3 values---None, Line Loop Request, Payload Loop Request)

• Loopback Control (2 values---disabled, payload loop, line loop if managed M1:3 multiplexor is configured)

• Line build-out (if managed M1:3 multiplexor is configured)

• Line Coding (if managed M1:3 Multiplexor is configured)

• Identifier String

• 15 TCA Thresholds (integer)

• BERT parameters

Usage

Command will not work with Release 2.2 or earlier.

Options

-sname SwitchName	Name of switch containing the DS1.
-card CardNum	Number of the card (2 to 16) containing the DS1.
-ds3 DS3Num	Number of the DS3 containing the DS1.
-ds1 DS1Num	Number of the DS1.
-as up | down | test	Admin Status of DS1 Port.
-chanmode clear | chan	Channelization mode---Clear Channel or Channelized.
-timing int | thru	Timing, Internal or Through.
-frm esf | sf | other	DS1 framing type, ESF, SF(D4), or Other (unknown).
-fdl ansi | none	DS1 Facilities Data Link.
-sc none | lineloop | payloop	DS1 Send Code.
-loop none | payload | line	DS1 Near End loopback control.
-lbo 133 | 266 | 399 | 533 | 665	DS1 Line Build-out upper range.
-lcode ami | b8zs	DS1 line coding.
-name Ds1Name	DS1 Physical Line Description or Identifier String.
-cfgs 1	DS1 Port Configuration save to non-volatile memory, any integer saves.
-tes15 Value	Errored Seconds 15-minute TCA threshold setting value.
-tes24 Value	Errored Seconds 24-hour TCA threshold setting value.
-tses15 Value	Severely Errored Seconds 15-minute TCA threshold setting value.
-tses24 Value	Severely Errored Seconds 24-hour TCA threshold setting value.
-tsefs15 Value	Severely Errored Framing Seconds 15-minute TCA threshold setting value.
-tsefs24 Value	Severely Errored Framing Seconds 24-hour TCA threshold setting value.
-tpcv15 Value	Path Coding Violations 15-minute TCA threshold setting value.
-tpcv24 Value	Path Coding Violations 24-hour TCA threshold setting value.
-tuas15 Value	Unavailable Seconds 15-minute TCA threshold setting value.
-tuas24 Value	Unavailable Seconds 24-hour TCA threshold setting value.
-taiss15 Value	Alarm Indication Signal Seconds 15-minute TCA threshold setting value.
-taiss24 Value	Alarm Indication Signal Seconds 24-hour TCA threshold setting value.
-tcss15 Value	Controlled Slip Seconds 15-minute TCA threshold setting value.
-tcss24 Value	Controlled Slip Seconds 24-hour TCA threshold setting value.
-toof15 Value	Out-of-Frame Events 15-minute TCA threshold setting value.
-toof24 Value	Out-of-Frame Events 24-hour TCA threshold setting value.
-tfeles15 Value	Far End Line Errored Seconds 15-minute TCA threshold setting value.
-tfeles24 Value	Far End Line Errored Seconds 24-hour TCA threshold setting value.
-tfees15 Value	Far End Errored Seconds 15-minute TCA threshold setting value.
-tfees24 Value	Far End Errored Seconds 24-hour TCA threshold setting value.
-tfeses15 Value	Far End Severely Errored Seconds 15-minute TCA threshold setting value.
-tfeses24 Value	Far End Severely Errored Seconds 24-hour TCA threshold setting value.
-tfesefs15 Value	Far End Severely Errored Framing Seconds 15-minute TCA threshold setting value.
-tfesefs24 Value	Far End Severely Errored Framing Seconds 24-hour TCA threshold setting value.
-tfepcv15 Value	Far End Path Coding Violations 15-minute TCA threshold setting value.
-tfepcv24 Value	Far End Path Coding Violations 24-hour TCA threshold setting value.
-tfeuas15 Value	Far End Unavailable Seconds 15-minute TCA threshold setting value.
-tfeuas24 Value	Far End Unavailable Seconds 24-hour TCA threshold setting value.
-tfecss15 Value	Far End Controlled Slip Seconds 15-minute TCA threshold setting value.
-tfecss24 Value	Far End Controlled Slip Seconds 24-hour TCA threshold setting value.
-bertframe esf | sf | none	DS1 framing to use when performing a BERT. Can't change while test is running.
-bertpatt allones | 511 |2047 | qrss | 2^23-1 | 3in24 | user	BERT pattern. Can't change while test is running.
-userpatt hexPattern	User defined BERT pattern. A 32 bit pattern represented by an 8 character hexadecimal number. Can't change while test is running.
-userpattlen Value	User defined BERT pattern length. A number from 1 to 32. Can't change while test is running.
-txpattinv off | on	BERT transmit pattern bit inversion control. Can't change while test is running.
-rxpattinv off | on	BERT receive pattern bit inversion control. Can't change while test is running.
-bert on | off	Controls the running of the integrated BERT for this DS1.
-bertrestart yes | no	Restarts the running BERT. Only applies when -bert on. Yes = 2. No = 1.
-1bitinsert yes | no	Inserts a single bit error into the transmitted BERT pattern. Only applies when -bert on. Yes = 2. No = 1.
-conterrinsert none | minus1 | minus2 | minus3 | minus4 | minus5 | minus6 | minus7	Continously inserts bit errors into the transmitted BERT pattern at a rate of 10 to the minus 1 through 7. Can be modified while the test is running.

If chanmode, timing, or frm attributes are being changed, all three of these attributes must be specified. Neither of these attributes may be changed when Private Line connections exist on the DS1 port being modified.

Example

VCLI>>change phys ds1 -sname tulsa1 -card 3 -ds3 1 -ds1 8 -as 2 -name DS1_3_8

change physicalport ds3

Purpose

Changes the following attributes of a DS3 port:

• Admin Status (3 values---up, down, test)

• Line type (2 values---M23, C-bit parity)

• FEAC Send Code (3 values---None, Line Loop Reqiuest, Payload Loop Request)

• Loopback Control (3 values---none, in, out)

• AIS to Yellow (2 values---no, yes)

• Line Length (2 values---short, long)

• Optional Managed M13 IP address (in decimal dot notation)

• Optional Managed M13 Net Mask (in decimal dot notation)

• Optional Managed M13 Community String

• Identifier String or name for specified DS3

• 16 TCA Thresholds (integer)

Usage

Command will not work with Release 2.2 or earlier.

Option

-sname SwitchName	Name of switch containing the DS3
-card CardNum	Number of the card (2 to 16) containing the DS3
-ds3 DS3Num	Number of the DS3 port
-as up | down | test	Admin Status of DS3 Port
-lt m23 | cbit	DS3 Line Type
-sc none | lineloop | payloop	DS3 Send Code
-name DS3Name	DS3 Physical line Description or Identifier String
-loop none | out | in	DS3 Near End loopback control
-aistoy no | yes	DS3 AIS to Yellow, Send Yellow signal on Rxed AIS
-ll short | long	DS3 Line Length
-cfgs 1	DS3 Port Configuration save to non volatile memory, any integer saves
-tpes15 Value	P-bit Errored Seconds 15-minute TCA threshold setting value
-tpes24 Value	P-bit Errored Seconds 24-hour TCA threshold setting value
-tpses15 Value	P-bit Severely Errored Seconds 15-minute TCA threshold setting value
-tpses24 Value	P-bit Severely Errored Seconds 24-hour TCA threshold setting value
-tpcv15 Value	P-bit Coding Violations 15-minute TCA threshold setting value
-tpcv24 Value	P-bit Coding Violations 24-hour TCA threshold setting value
-tsefs15 Value	Severely Errored Framing Seconds 15-minute TCA threshold setting value
-tsefs24 Value	Severely Errored Framing Seconds 24-hour TCA threshold setting value
-tles15 Value	Line Errored Seconds 15-minute TCA threshold setting value
-tles24 Value	Line Errored Seconds 24-hour TCA threshold setting value
-tlses15 Value	Line Severely Errored Seconds 15-minute TCA threshold setting value
-tlses24 Value	Line Severely Errored Seconds 24-hour TCA threshold setting value
-tlcv15 Value	Line Coding Violations 15-minute TCA threshold setting value
-tlcv24 Value	Line Coding Violations 24-hour TCA threshold setting value
-tuas15 Value	Unavailable Seconds 15-minute TCA threshold setting value
-tuas24 Value	Unavailable Seconds 24-hour TCA threshold setting value
-taiss15 Value	Alarm Indication Signal Seconds 15-minute TCA threshold setting value
-taiss24 Value	Alarm Indication Signal Seconds 24-hour TCA threshold setting value
-tces15 Value	C-bit Errored Seconds 15-minute TCA threshold setting value
-tces24 Value	C-bit Errored Seconds 24-hour TCA threshold setting value
-tcses15 Value	C-bit Severely Errored Seconds 15-minute TCA threshold setting value
-tcses24 Value	C-bit Severely Errored Seconds 24-hour TCA threshold setting value
-tccv15 Value	C-bit Coding Violations 15-minute TCA threshold setting value
-tccv24 Value	C-bit Coding Violations 24-hour TCA threshold setting value
-tfeces15 Value	Far End C-bit Errored Seconds 15-minute TCA threshold setting value
-tfeces24 Value	Far End C-bit Errored Seconds 24-hour TCA threshold setting value
-tfecses15 Value	Far End C-bit Severely Errored Seconds 15-minute TCA threshold setting value
-tfecses24 Value	Far End C-bit Severely Errored Seconds 24-hour TCA threshold setting value
-tfeccv15 Value	Far End C-bit Coding Violations 15-minute TCA threshold setting value
-tfeccv24 Value	Far End C-bit Coding Violations 24-hour TCA threshold setting value
-tfeuas15 Value	Far End Unavailable Seconds 15-minute TCA threshold setting value
-tfeuas24 Value	Far End Unavailable Seconds 24-hour TCA threshold setting value
-m13ipaddr IpAddress	IP address of the M13 connectio to the DS3
-m13mask IpAddress	Net Mask for IP address of M13
-community Value	Community string used to manage M13

Example

VCLI>>change phys ds3 -sname tulsa1 -card 3 -ds3 1 -as 2 -ll 2 -name Card_3_DS3_1

change physicalport oc3

Purpose

Changes the following attributes of an OC3 port:

• Admin Status (3 values---up, down, test) ---applies to all ports independently

• Transmit Clock Source (2 values---local, loop)--- applies to OC3 ports 1 and 3 only

• Cell Payload Scrambling (2 values---enabled, disabled)--- applies to OC3 ports 1 and 3 only

• Loopback Control (3 values---none, in, out)---applies to port 1 and 2 independently

• AIS to yellow (2 values---no and yes)

• Identifier String---applies to port 1 and 2 independently

• 22 TCA Thresholds (integer)

Usage

Some attributes can only be set on OC3 port 1 and 3, but will also be reflected on OC3c ports 2 and 4. Because ports 1 and 2 as well as ports 3 and 4 are APS pairs , setting configurable items on ports 1 and 3 are set on ports 2 and 4 automatically.

Options

-accesspath (1 to 3)	Identify the path layer on the access side. Needed only for CS3 blade types with 4 OC3 ports on the I/O card.
-as up | down | test	Admin Status of OC3 Port (1 to 4).
-card CardNum	Number of card (2 to 16) containing the OC3.
-cfgs 1	OC3 Port Configuration save to non volatile memory, any integer saves.
-community	lodsxM13CommunityString.
-loop none | in | out	OC3 loopback control.
-m13ipaddr	lodsx3M13IpAddr.
-m13mask	lodsx3M13IpNetMask.
-name OC3Name	OC3 Physical line Description or Identifier String.
-oc3 OC3Num	Number of the OC3 port.
-scram disable | enable	Cell payload scrambling.
-sname SwitchName	Name of switch containing the OC3.
-tclk loop | local	OC3 Transmit Clock source.
-tfelcv15 Value	Far End Line Coding Violations 15-minute threshold.
-tfelcv24 Value	Far End Line Coding Violations 24-hour threshold.
-tfeles15 Value	Far End Line Errored Seconds 15-minute threshold.
-tfeles24 Value	Far End Line Errored Seconds 24-hour threshold.
-tfelses15 Value	Far End Line Severely Errored Seconds 15-minute threshold.
-tfelses24 Value	Far End Line Severely Errored Seconds 24-hour threshold.
-tfeluas15 Value	Far End Line Unavailable Seconds 15-minute threshold.
-tfeluas24 Value	Far End Line Unavailable Seconds 24-hour threshold.
-tfepcv15 Value	Far End Path Coding Violations 15-minute threshold.
-tfepcv24 Value	Far End Path Coding Violations 24-hour threshold.
-tfepes15 Value	Far End Path Errored Seconds 15-minute threshold.
-tfepes24 Value	Far End Path Errored Seconds 24-hour threshold.
-tfepses15 Value	Far End Path Severely Errored Seconds 15-minute threshold.
-tfepses24 Value	Far End Path Severely Errored Seconds 24-hour threshold.
-tfepuas15 Value	Far End Path Unavailable Seconds 15-minute threshold.
-tfepuas24 Value	Far End Path Unavailable Seconds 24-hour threshold.
-tlais15 Value	Line Alarm Indication Signal Seconds 15-minute threshold.
-tlais24 Value	Line Alarm Indication Signal Seconds 24-hour threshold.
-tlcv15 Value	Line Coding Violations 15-minute threshold.
-tlcv24 Value	Line Coding Violations 24-hour threshold.
-tles15 Value	Line Errored Seconds 15-minute threshold.
-tles24 Value	Line Errored Seconds 24-hour threshold.
-tlses15 Value	Line Severely Errored Seconds 15-minute threshold.
-tlses24 Value	Line Severely Errored Seconds 24-hour threshold.
-tluas15 Value	Line Unavailable Seconds 15-minute threshold.
-tluas24 Value	Line Unavailable Seconds 24-hour threshold.
-tpais15 Value	Path Alarm Indication Signal Seconds 15-minute threshold.
-tpais24 Value	Path Alarm Indication Signal Seconds 24-hour threshold.
-tpcv15 Value	Path Coding Violations 15-minute threshold.
-tpcv24 Value	Path Coding Violations 24-hour threshold.
-tpes15 Value	Path Errored Seconds 15-minute threshold.
-tpes24 Value	Path Errored Seconds 24-hour threshold.
-tpses15 Value	Path Severely Errored Seconds 15-minute threshold.
-tpses24 Value	Path Severely Errored Seconds 24-hour threshold.
-tpuas15 Value	Path Unavailable Seconds 15-minute threshold.
-tpuas24 Value	Path Unavailable Seconds 24-hour threshold.
-tscv15 Value	Section Coding Violations 15-minute threshold.
-tscv24 Value	Section Coding Violations 24-hour threshold.
-tses15 Value	Section Errored Seconds 15-minute threshold.
-tses24 Value	Section Errored Seconds 24-hour threshold.
-tssefs15 Value	Section Severely Errored Framing Seconds 15-minute threshold.
-tssefs24 Value	Section Severely Errored Framing Seconds 24-hour threshold.
-tsses15 Value	Section Severely Errored Seconds 15-minute threshold.
-tsses24 Value	Section Severely Errored Seconds 24-hour threshold.

Example

VCLI>>change phys oc3 -sname tulsa1 -card 3 -oc3 1 -tclk local -name tulsa1_3_OC3_1

change switch sntp

Purpose

Changes switch's Synchronous Network Time Protocol (SNTP) information, including the following:

• Operating mode

• Primary server IP address

• Secondary server IP address

• Time correction

• Server timeout

• Protocol admin

• Polling period

• Number of samples from server

Options

-sname SwitchName	Name of switch to change in-band management for.
-card CardNum	Number of the card (2 to 16) to change in-band management for.
-cardtype imc|cs3|all	Card type to apply SNTP changes to (no default).
-opermode multicast |anycast | unicast	Operation mode of the SNTP. Release 3.0 supports only unicast.
-primaryaddr IPAddress	Primary SNTP server IP address.
-secondaddr IPAddress	Secondary SNTP server IP address. Used only if primary is down.
-timecorrection TimeCorrectionValue	Maximum percentage of time correction allowed, in relation to client time.
-timeout TimeoutValue	Timeout for server reply.
-admin enable | disable	Administrative status of the client operations (Enabled means SNTP is enabled.)
pollperiod PollingValue	Polling period by the client. Measured in seconds.
samples NumSamples	Number of samples to be gathered from server before making calcualtions for client's local time setting.

Example

VCLI>>change swtich sntp -sname tulsa1 -cardtype cs3 -primaryaddr 172.29.58.101

change system operator

Purpose

Changes the privilege level for a VCLI operator account. The three levels are

• Admin

• Change

• Show

Usage

Command requires admin privilege level.

Options

Example

VCLI>>change system operator -name jdsmith -priv change

change system switch

Purpose

Changes the following attributes of an MGX 8240 switch:

• Switch Name---Identifies the switch in all commands with the switch name identifier -sname. Can only be alphanumeric and underscore characters; length limit is 64 characters.

• Out-of-band IP Address of switch---Using decimal dot notation (for example, 206.14.150.201) [optional].

• Community String for reading and writing to the switch [optional].

• Chassis ID number---Factory assigned chassis ID number. You can find this on the barcode sticker below power input [optional].

Usage

Command requires admin privilege level.

Options

-sname SwitchName	Name of the existing switch to be changed
-newname NewSwitchName	New name to change the switch to (optional)
-ipaddr IPAddress	New out-of-band management IP address (optional)
-community String	ASCII string to be used as the SNMP community string in all Set and Get SNMP PDUs sent to the cards in this switch
-chassisid ChassisId	Chassis ID number for the switch
-ftppass password	For downloading software images; use up to 8 characters

Example

VCLI>>change system switch -sname tulsa1 -community linear93

delete connection

Purpose

Removes a connection. This connection can be either a local Private Line segment (between DS1 interface and the ATM trunk) or a local Private Line (between two DS1 interfaces). The connection can be a remote Private Line (between two DS1 interfaces on different cards), as long as

• ATM Network Provisioning Server has been configured and is reachable.

• Both cards have uplink port information configured.

Option

-epid EndpointId	Endpoint ID of connection to be deleted.
-partial 1	Delete nearend point only.

Example

VCLI>>del connection -sname tulsa1 -card 3 -epid 279

delete system cescard

Purpose

Removes a CES card from the VCLI system.

Options

-sname SwitchName	Name of switch to remove this card from.
-card CardNumber	Slot number of card to remove.
-noconfirm 1	Execute this command without prompting for confirmation.

Example

VCLI>>del sys cescard -sname tulsa1 -card 2

delete system operator

Purpose

Removes an operator from the VCLI system.

Usage

Command requires admin privilege level.

Option

-name OperatorName

Name of the operator to delete

Example

VCLI>>del sys operator -name jdsmith
Are you sure [No]?

delete system switch

Purpose

Removes a switch from the VCLI system.

Usage

Command requires admin privilege level.

Option

-sname SwitchName

Name of the switch to delete

Example

VCLI>>del sys switch -sname tulsa1
Are you sure [No]?

download

Purpose

Downloads software image to a switch.

Note The software will be taken from the directory pointed to by ImageDir . It will be downloaded to all of the type of cards specified in the -cardtype argId, or to a single card identified with either the -card or -physcard argIds.

The image directory will have two subdirectories: software and firmware. The directory files (including subdirectories) from the workstation in each directory will be downloaded to the individual card's directory pointed to by the following:

If -swcmd is specified, the swdwnld command will be set on the switch after the image is downloaded. This is an optional arg ID.

Options

-network 1	All switches in the network.
-sname SwitchName	Specific switch name.
-card CardNumber	Number of the logical card; may not be the actual card in some redundancy situations.
-physcard CardNumber	Number of the actual card; overrides existing redundancy roles.
-swcmd Cmd	Optional command to force a software switch upon download.
-noconfirm 1	Execute this command without prompting user for confirmation.
-verbose 1	Provides feedback during the download process.
cardtype cs3/imc	Downloads cards of the same type. Options are imc = 1, cs3 = 2.

Example

VCLI>>download -sname demoroom -physcard6 -swcmmd 3
Are you sure [NO]?

exit

Purpose

Terminates VCLI session and returns control to the UNIX shell.

Example

VCLI>>exit

show alarms detail

Purpose

Shows the details of every currently active alarm in the whole network, on a single switch, or on a single card. Details shown are

• Date and time the alarm condition began

• Severity of the alarm (critical, major, minor)

• String describing the alarm type of alarm and what is alarming

Options

-network	Shows all alarms in the network
-sname SwitchName	Name of switch to display alarms for
-card CardNum	Number of the card (2 to 16) to display alarms for

Example

VCLI>>show alarms detail -sname tulsa1 -card 3
Severity Date     Time     Description
Critical 09/28/98 03:00:57 Receiving AIS Alarm, Failure on DS3/DS1=1/2

show alarms summary

Purpose

Shows which cards and switches have active alarms.

For -network, lists all switches that have an alarm.

For -sname, lists all cards that have an alarm.

For -card, shows if the card has an alarm or not.

Options

-network	Lists all switches that have an alarm
-sname SwitchName	Lists all cards that have an alarm
-card CardNumber	Shows if the card has an alarm or not

Example

VCLI>>show alarms summary -sname tulsa1
Alarming Switch: tulsa2
Alarming Card(s): 2 4 9

show blademon information

Purpose

Shows blademon information, for any card or for a whole switch:

For a CES card, the command shows the following information:

• Card uplink info

• Card type (CES or IMC)

• Physical slot

• Logical slot (same as physical slot unless the card is a switched-in backup, in which case it takes on the slot of the primary

• In-band and out-of-band IP addresses

• SNMP UDP port number used for in-band and out-of-band IP addresses

• Availability state of each IP address

• Current IP address being used for communicating with CES (labelled `current interface')

• Redundancy role (primary, backup, or none)

• Redundancy state (NormalState, InvalidState, Backup-SwitchedIn, Primary-SwitchedOut)

• Software version on the card

• SNMP community string

For an IMC card, the command shows the following information:

• Physical slot (1A or 1B)

• Card type (CES or IMC)

• Out-of-band IP addresses

• SNMP UDP port number used for out-of-band IP address

• Redundancy role (primary or backup)

• Redundancy state (Unknown, Primary-ActiveMode, Backup-StandbyMode, Backup-Unavailable)

• Software version on the card

• SNMP community string

Options

Example

VCLI>> show blademon information -sname tulsa1
Switch Name: tulsa1, Card: 1
Card Type: IMC
Current Interface:	OOBand
OOBand IP Address:	172.29.58.140
OOBand UDP Port:	161
Community String:	public
 
IMC SLOT:1A
Redundancy Role:	Primary
Redundancy State:	Invalid State
Software Version:	2.2.0.10
 
IMC SLOT:1B
Redundancy Role:	Back up
Redundancy State:	Back Up Switched IN
Software Version:	2.2.0.10
 
Switch Name: tulsa1, Card: 9
Card Type: Ces card
Uplink:	UpLinkInfoString
Blade S/W Version:	3.0.0.13
Blade Role:	None	Blade OperState: NormalState
Logical Slot: 	9
Community String:	public
Current Interface:	OOBand
InBand IP Address: 	10.128.0.9
OOBand IP Address:	172.29.58.140
InBand UDP Port:	161	OOBand UDP Port:	9001
InBand State:	DOWN
OOBand State:	UP

show blademon statistics

Purpose

Shows the background pollers' information for a card or for all cards in a switch. This command allows users to see how the CES or IMC card is being managed by the VCLI.

For CES and IMC cards, this command shows statistics for out-of-band interfaces. The following information is shown:

• Total number of polls transmitted

• Total number of responses to polls received

• Total number of unacknowledged polls

• Total amount of data received from a card

• Total number of errored responses from a card

• Total data transmitted

• Time last poll was transmitted

• Time when the last errored response was received

• Time of the last unacknowledged poll

• Time when then interface went operationally active

• Time when the interface went operationally inactive.

• Number of consecutive unacknowledged polls from a card

• Number of consectuive errored responses from a card

Note Data units are in bytes unless otherwise indicated.

Options

-sname SwitchName	Lists all cards that have an alarm
-card CardNum	Number of the card (1 to 16)

Example

Note A display of "---------------" indicates that the condition in that field has never occurred.

VCLI>> show blademon statistics -sname tulsa1
Switch Name: tulsa1, Card: 1
Card Type: IMC
 
OOBand
-----------
Total Reqs Sent	48
Total Resp Received:	48
Total Err Resp Received:	0
Total UnAcked Reqs:	0
Total Data Sent	4800
Total Data Received:	6048
Last Polled Time:	Tue Aug 24 18:54:32
Last Err Resp Red:	-----------------------------
Last Unacked Req: 	----------------------------
Oper Start Time: 	Tue Aug 24 18:54:32
Oper End Time	 ---------------------------------
 
Switch Name: tulsa1, Card: 1
Card Type: CES
 
InBand		OOBand	
-----------		-----------
Total Reqs Sent	24	Total Reqs Sent	24
Total Resp Received:	0	Total Resp Received:	0
Total Err Resp Received:	0	Total Err Resp Received:	0
Total UnAcked Reqs:	24	Total UnAcked Reqs:	0
Total Data Sent	2400	Total Data Sent	2400
Total Data Received:	0	Total Data Received:	3360
Last Polled Time:	Tue Aug 24 18:54:32	Last Polled Time:	Tue Aug 24 18:54:32
Last Err Resp Rec:	---------------------	Last Err Resp Rec: 	-------------------
Last Unacked Req:	Tue Aug 24 18:54:32	Last Unacked Req:	-------------------
Oper Start Time: 	---------------------	Oper Start Time: 	Tue Aug 24 18:54:32
Oper End Time	 --------------------	Oper End Time	-------------------

show cescard aps detail

Purpose

Shows all SONET APS information (configuration, status, statistics), including:

• Administrative Status (2 values---enabled, disabled)

• Protocol State (9 values---lockout, forced switch, signal failure, signal degrade, manual switch, wait to restore, reverse request, do not revert, no request)

• Line in use (2 values---working line, protection line)

• Failures (shows 5 failure states: protection switched, protection byte failure, channel mismatch failure, mode mismatch failure, none)

• Number of APS switches

• Architecture (2 values---1plus1, 1for1)

• Remote Architecture (2 values---1plus1, 1for1)

• Directional Mode (2 values---unidirectional, bidirectional)

• Remote Directional Mode (2 values---unidirectional, bidirectional)

• Revertive Mode (2 values---nonrevertive, revertive)

• BERT Threshold (6 values---10^-4, 10^-5, 10^-6, 10^-7, 10^-8, 10^-9)

• Wait To Restore Period (integer 0 to 720)

• Commands (6 values---clear, lockout, forced switch of working, forced switch of protection, manual switch of working, manual switch of protection)

Options

-network	Shows APS for every card in the network
-sname SwitchName	Name of containing switch to show card APS for
-card CardNum	Number of the card (2 to 16) to show APS for (optional)

Example

VCLI>>show cescard aps detail -sname tulsa1 -card 4
AdminSts: Enabled   ProtocolState: NoRequest       LineInUse: Working
SwitchCount: 0      Failures: None
Arch: 1+1 RemoteArch: 1+1 DirMode: BiDirectional RemDirMode: BiDirectional
RevertiveMode: NonRevertive BERThresh: 1e-4 WTRPeriod: 360
LastCommand: Clear
 

For those CS3 blade types with an OC3 I/O card, the APS information is displayed for both ATM trunk OC3 and Channelized access OC3.

show cescard aps summary

Purpose

Shows the following summary information about the SONET APS status of a card's OC3c trunk port:

• Administrative Status (2 values---enabled, disabled)

• Protocol State (9 values---lockout, forced switch, signal failure, signal degrade, manual switch, wait to restore, reverse request, do not revert, no request)

• Line in use (2 values---working line, protection line)

• Failures (shows zero to 4 failure statuses: protection switched, protection byte failure, channel mismatch failure, mode mismatch failure)

Options

-network	Shows APS for every card in the network
-sname SwitchName	Name of containing switch to show card APS for
-card CardNum	Number of the card (2 to 16) to show APS for (optional)

Example

VCLI>>show cescard aps summary -sname tulsa1
Card	Side	AdminSts	Protocol State	Line In Use	Failures
2	Trunk	Enabled	Signal Degrade	Protection	ProtSwitched
3	Trunk	Enabled	No Request	Working
4	Trunk	Disabled	No Request	Working	

show cescard config

Purpose

Shows the following configuration information about a card:

• Name string

• Location string

• Contact information string

• Chassis External IP Address

Options

-network	Shows all cards in the network
-sname SwitchName	Name of switch to display cards for
-card CardNum	Number of the card (2 to 16) to display information for

Example

VCLI>>show cescard config -sname tulsa1 -card 3
Name: tulsa1_card3
Location: tulsa_pop_rack5_chassis2_slot2
Contact: Jose_Montoya_(772)555-1212
Fan Monitoring: Enabled
Chassis IP address: 10.100.0.254

show cescard info

Purpose

Shows the following information about a card:

• Type of card (CES or IMC)

• Software version

• Current date and time

• Part number

• Serial number

• CLEI Code

• Date of manufacture

• Hardware revision

• CES or CS3 card type

• I/O card type

Options

-network	Shows all cards in the network
-sname SwitchName	Name of switch to display cards for
-card CardNum	Number of the card (2 to 16) to display information for

Example

VCLI>>show cescard info -sname tulsa1 -card 3
Software Version: Sentient Networks, MGX 8420, Release 3.0.0.1
Current Date/Time: 02/12/00 15:33:07 GMTShows
Part Number: 205a000102revb 	Serial Number: 0001a00134
CLEI Code: BATHFHZ0DAA	Date of Manufacture: 10/03/98
Card Type: CES	 I/O	 Card Type: 3 DS3s, 2 OC3s
Fab Number: 312307	PCB Part Number
MAC Address: 00:00:01:1a:0d:1c	Cisco Standard Card Type:
Access Status: Active
RMA Failure Code: 0	RMA History Code: 35

show cescard linkinfo

Purpose

Shows the linkinfo configuration for a card, including the following:

• Uplink number

• Uplink logical port

Options

-network	Shows uplink info for every card in the network
-sname Switch Name	Name of switch to show card uplink information for

Example

VCLI>>show ces linkinfo -sname tuls1
Switch Name: tulsa1, Card:1
Card	Uplink Number	Uplink Logical Port2
2	2		switch_ip.172.29.59.172.card.2.pport.2.lport.2
3	3		switch_ip.172.29.59.172.card.3.pport.3.lport 3
4	0
5	0
6	0
7	0
8	0
9	0
10	0
11	0
12	0
13	0
14	0
15	0
16	0

show cescard redundancy

Purpose

Shows the following redundancy configuration and status for a card:

• Redundancy Role (primary, backup, none)

• Redundancy State

If the Redundancy Role is None (neither Primary nor Secondary), the following is also shown:

• Backup card number

For a card with a Redundancy State of Switched-in, the following is shown:

• Card Switched-in for

• Failure Reason(s)

Options

-network	Shows all cards in the network
-sname SwitchName	Name of switch to display cards for
-card CardNum	Number of the card (2 to 16) to display information for

Example

Command example for a non-redundant card:

VCLI>>show cescard redundancy -sname tulsa1 -card 6
Redundancy Role: None     Redundancy State: Non-redundant
 

Command example for a switched-out primary card:

VCLI>>show cescard redundancy -sname tulsa1 -card 4
Redundancy Role: Primary	 Redundancy State: Switched-out/Self-failure
Backup Card Number: 2 
 

Command example for a switched-in backup card:

VCLI>>show cescard redundancy -sname tulsa1 -card 2
Redundancy Role: Backup   Redundancy State: Switched-in
Backup Card Number:2 	Switched-in For Card:4 	Reason: 100
 Info String: Force switch over

show cescard refclock config

Purpose

Shows how reference clocks for a CES card are currently configured, including the following:

• Primary Timing Reference (5 values---none, BITS A, BITS B, OC3 1, OC3 2)

• Secondary Timing Reference (5 values---none, BITS A, BITS B, OC3 1,OC3 2)

• Revertive Switching (2 values---disabled, enabled)

• Force Free Run (2 values---off, on)

Options

-network	Shows refclock configuration for every cescard in the network
-sname SwitchName	Name of switch to show refclock configuration for
-card CardNum	Number of the card (2 to 16) to show refclock configuration for

Example

VCLI>>show cescard refclock config -sname tulsa1 -card 3
PriRef: BITS-A   SecRef: OC3-1   RevSwitch: Enabled   ForceFreeRun: Off
 

For CS3 card types and for I/O cards with 4OC3 ports, there are two APS sides. Card 4 in the previous example is such a card. When the show cescard aps summary command is entered, the card's componentType attribute described above must be queried to determine if APS on the access side is available. If it is, this command must make two reads of the APS table.

show cescard refclock status

Purpose

Shows the following card reference clock summary information:

• Current reference clock source in use (5 values---BITS A, BITS B, OC3 1, OC3 2, Free Run)

• BITS A status (good, LOS, AIS)

• BITS B status (good, LOS, AIS)

• OC3 1 Status (good, LOS)

• OC3 2 Status (good, LOS)

Options

-network	Shows refclock status for every cescard in the network
-sname SwitchName	Name of switch to show refclock status for
-card CardNum	Number of the card (2 to 16) to show refclock status for

Example

VCLI>>show cescard refclock status -sname tulsa1 -card 3
CurrRefClk: BITS-A
BITS-A-Sts: Good     BITS-B-Sts: LOS     OC3-1-Sts: Good     OC3-2-Sts: LOS

show cescard selfcheck

Purpose

Shows the following information about the backup card's selfcheck function:

• frequency of test (5 values---never, once a day, once an hour, once a minute, continuous)

• test status (2 values---no fault, fault)

• test fault location

• test hour (range 0-23)

Options

-network 1	Shows healthmonitor information for every backup card in the network
-sname SwitchName	Name of switch to show healthmonitor information for
-card CardNum	Number of the card (2 to 16) to show healthmonitor information for

Example

VCLI>>show ces selfcheck -sname tulsa1 -card 3
Switch Name: tulsa 1, Card: 3
Test Performed: Once a Day
Test Status: No fault
Test Hour: 12

show cescard summary

Purpose

Shows the following summary information about a card:

• In-band availability

• Out-of-band availability

• Redundancy role

• Redundancy state

• Time (in seconds) since last reset

• Whether it has any currently active alarms

Options

-network	Shows all cards in the network
-sname SwitchName	Name of switch to display cards for
-card CardNum	Number of the card (2 to 16) to display information for

Example

VCLI>>show cescard summary -sname tulsa1 -card 3
Reachability: Down   Out-of-band Reachability: Up
Redundancy Role: None     Redundancy State: Non-redundant
Up Time: 45 days, 17:45:09 hours    Alarms: None

show connection (all | pl |segpl) bertconfig

Purpose

Shows the following BERT configuration for the circuit:

• BERT direction (tdm | atm)

• BERT Pattern (7 values---All Ones, 511, 2047, QRSS, 223-1, 3 In 24, User Configurable)

• User Pattern (hex number representing a 32 bit number)

• User Pattern Length (integer 1 to 32)

• Transmit Pattern Inversion (2 values---not inverted, inverted)

• Receive Pattern Inversion (2 values---not inverted, inverted)

• Run Control (2 values---running, stopped)

• Continuous Error Insertion (8 values---no errors, 10 to 1, 10 to 2, 10 to 3, 10 to 4, 10 to 5, 10 to 6, 10 to 7)

Note When all is specified, the command shows both pl (local and remote private line connections), as well as segpl (local private line segments).

Options

-network	Shows every DS1 port in the network
-sname SwitchName	Name of switch containing the DS1
-card CardNum	Number of the card (2 to 16) containing the circuit(s)
-epid EndPointId	Requests display of a specific circuit within a card

Example

VCLI>>show connection bertconfig -sname tulsa1 -card 3 -epid 279
DS3: 1  DS1: 12   EPID: 279  	TestingState: Stopped    ErrorInsert: None
Pattern: QRSS        UserPattern: 0xAA55AA55  UserPatternLen: 32
TxPatternInvert: Off  RxPatternInvert: Off Direction: ATM

show connection (all | pl | segpl) bertstatus

Purpose

Shows the statistics from either a currently running circuit BERT, or from the last run circuit BERT. Statistics shown are

• Elapsed Test Time (seconds)

• Received Pattern Synchronization Status (2 values---in sync, loss of sync)

• Received Data/Pattern (32 bits displayed in hex)

• Percent Error Free Seconds (displayed as % to 3 decimal places---for example, 99.999%)

• Bit Error Rate (represented as a string in scientific notation---for example, 1.23e-7)

• Number of Bit Errors

• Errored Seconds

• Severely Errored Seconds

• Pattern Loss Seconds

• Error Free Seconds

Note When all is specified, the command shows both pl (local and remote private line connections), as well as segpl (local private line segments).

Options

-network	Shows every DS1 port in the network
-sname SwitchName	Name of switch containing the DS1
-card CardNum	Number of the card (2 to 16) containing the DS1
-epid EndpointId	Requests display of a specific circuit within a card

Example

VCLI>>show connection bertstatus -sname tulsa1 -card 3 -epid 279
DS3: 1  DS1: 12   EPID: 279 
TestingState: Stopped  ElapsedTime: 01:34:58  BER: 1.23e-10
PatternSync: InSync      RxedPattern: 0xAA55AA55  BitErrors: 3
ErrorFreeSecs: 01:34:57 ErroredSecs: 00:00:01 SevErroredSecs: 00:00:00
PercentErrorFreeSecs: 99.2%    PatternLossSecs: 00:00:00

show connection (all | pl | segpl) config

Purpose

Shows the following connection information:

• Admin Status (3 values---up, down, testing)

• Signaling Mode (2 values---None, Robbed Bit Signaling)

• Partial Fill (integer 20 to 47)

• Reassembly CDVT (integer 1 to 140)

• Max Reassembly buffer size factor (integer 1 to 40)

• CGA Mode (3 values---voice nontransparent, voice transparent, dataport transparent)

• On-hook Service Interface trunk conditioning Robbed Bit Signaling (integer 0 to 15)

• Off-hook Service Interface trunk conditioning Robbed Bit Signaling (integer 0 to 15)

• On-hook ATM Interface Robbed Bit Signaling trunk conditioning (integer 0 to 15)

• Off-hook ATM Interface Robbed Bit Signaling trunk conditioning (integer 0 to 15)

• Identifiers

• ATM VPI---for PL segment and remote PL

• ATM VCI---for PL segment and remote PL

• Cell Rate---for PL segment and remote PL

• Endpoint 2 switch name---for PL

• Endpoint 2 card number---for PL

• Endpoint 2 Endpoint ID---for PL

• Creation time

• Last modify time

• Loss of Cell Alarm (2 values, enabled, disabled)

• 9 different TCA thresholds (integers)

Note When all is specified, the command shows both pl (local and remote private line connections), as well as segpl (local private line segments).

Options

-network	Shows every connection in the network
-sname SwitchName	Name of switch containing the connection(s)
-card CardNum	Number of the card (2 to 16) containing the connection(s)
-ds3 DS3Num	Number of the DS3 port containing the connection(s)
-ds1 DS1Num	Number of the DS1 port containing the connection(s)
-epid EndpointId	Requests display of a specific connection within a particular card

Examples

VCLI>>show conn all config -sname tulsa1 -card 3 -ds3 3
DS3: 3   DS1: 1 EPID: 279 ChanMode: Chan CktId: twc-1234567-pl
CktNum: 1234567890 CustName: Bobs_nifty_stuff
Type: PL-segment AdminSts: Up       PartFill: 0   CellRate: 4185 SigMode: Robbed
Loopback: None
ReassemCDVT (0.1 ms): 30 MaxReassemBufSizFac: 20 CGAMode: Voice-NonTransp
OnHookServTC: 0   OffHookServTC: 3   OnHookATMTC: 0   OffHookATMTC: 3
VPI: 0 VCI: 497   Created: 10/21/98 12:34:08 Modified: 10/21/98 12:46:34
Generate LOC Alarm: Enabled
TCA Thresholds	15 Min	24-hour
Cells w/Hdr Errors	24	240
Pointer Reframes	4	40
Pointer Parity Errors	12	120
Sequence Errors	24	240
Lost Cells	36	360
Misinserted Cells	12	120
Buffer Underflows	6	60
Buffer Overflows	6	60
Dropped Cells	48	480

DS3: 3   DS1: 2 EPID: 280   ChanMode: Chan CktId: twc-2345678-pl
CktNum: 1972476202 CustName: Jimmys_cool_stuff
Type: remote-PL AdminSts: Up       CellRate: 4107
Loopback: none
ReassemCDVT (0.1 ms): 30 MaxReassemBufSizFac: 20
VPI: 0 VCI: 498   Created: 10/21/98 12:57:08 Modified: 10/21/98 12:57:08
EP2Card: 11 EP2EPID: 269 EP2SwName: boston22
Generate LOC Alarm: Enabled
TCA Thresholds	15 Min	24-hour
Cells w/Hdr Errors	24	240
Pointer Reframes	4	40
Pointer Parity Errors	12	120
Sequence Errors	24	240
Lost Cells	36	360
Misinserted Cells	12	120
Buffer Underflows	6	60
Buffer Overflows	6	60
Dropped Cells	48	480

show connection (segpl | pl | all) statistics

Purpose

Shows the following statistics for a Private Line or Private Line segment:

• Cells Reassembled

• Cells with Header Errors

• Pointer Reframes

• Pointer Parity Errors

• Sequence Errors

• Lost Cells

• Misinserted Cells

• Buffer Underflows

• Buffer Overflows

• Dropped Cells

Note When all is specified, the command shows both pl (local and remote private line connections), as well as segpl (local private line segments).

Options

-network	Shows every connection in the network.
-sname SwitchName	Name of switch containing the connection(s).
-card CardNum	Number of the card (2 to 16) containing the connection(s).
-ds3 DS3Num	Number of the DS3 port containing the connection(s).
-ds1 DS1Num	Number of the DS1 port containing the connection(s).
-epid EndpointId	Specific connection within a particular card.
-15m IntervalNum	Requested 15-minute interval number (from 0 to 96). 0 indicates current interval, 1 is previous 15-minute interval, 96 is the 96th interval into the past.
-24h IntervalNum	Requested 24-hour interval number (from 0 to 1). 0 indicates current interval, 1 is previous 24-hour interval.

Example

VCLI>>show conn segpl statistics -sname tulsa1 -card 3 -epid 279
DS3: 1 DS1: 12 EPID: 279 CktId: twc-1234567-pl
Current 15-minute Interval Elapsed Time (min:sec) 10:09
Cells Reassembled	0	Cells w/Hdr Errors		0
Pointer Reframes	0	Pointer Parity Errors		0
Sequence Errors	0	Lost Cells		0
Misinserted Cells	0	Buffer Underflows		0
Buffer Overflows	0	Dropped Cells		0
Payload Cells Txed	0	Trunk Cond. Cells Txed		0
Suppressed Tx Cells	0

show connection (all | segpl | pl) summary

Purpose

Shows the following connection information:

• Physical port that the connection terminates on

• Endpoint ID

• Connection type (PL segment, local PL, remote PL)

• Admin Status

• Oper Status

• Provisioning Incomplete

• Set administratively down

• Physical Container down

• No Circuit Configured

• Persistent Loss of Cells

• Receiving ATM OAM AIS---Does not apply to local Private Line connections.

• Receiving ATM OAM RDI---Does not apply to local Private Line connections.

• ATM Interface Down---Does not apply to local Private Line connections.

• Internal connection to the destination bearer channel is not established. This could be caused by deletion of the destination connection endpoint or bearer channel.

• Last OAM loopback status.

Note When all is specified, the command shows both pl (local and remote private line connections), as well as segpl (local private line segments).

Options

-network	Shows every connection in the network
-sname SwitchName	Name of switch containing the connection(s)
-card CardNum	Number of the card (2 to 16) containing the connection(s)
-ds3 DS3Num	Number of the DS3 port containing the connection(s)
-ds1 DS1Num	Number of the DS1 port containing the connection(s)
-epid EndpointId	Requests display of a specific connection within a particular card.

Example

VCLI>>show conn all summary -sname tulsa1 -card 3 -ds3 3 -ds1 5
DS3	DS1	EPID	CktId	Type	AdminSts	OamLoopSts	OperStatus
3	 5	 279	twc-1234567-pl	PL segment	Up 	InProgress	DS1Down	 ATM	Down
3	 5	1012	twc-2345678-pl	remote-PL	Down	None	Admin	Down

show delaytest config

Purpose

Shows the following configuration information for max test or tests:

• Test number (1 to 30).

• Endpoint ID of the test.

• Test state disabled/enabled.

• Test duration as configured by the last user (in seconds).

• Remaining seconds for the test---0 for disabled tests; 1 or greater for tests in progress.

Note Maximum tests possible are 30 per blade.

Options

-sname SwitchName	Name of switch containing the delay tests
-card CardNum	Number of the card (2 to 16) containing the tests
-testnum Integer	Number from 1 to 30 that identifies a particular test.

Example

VCLI>>show delaytest config -sname tulsa1 -card 3
Test    EPID    Testing   Duration  Remaining Time
Number          State     (secs)    (days:hr:min:sec)
 
1       0       Disabled    0         000:00:00:00
2       0       Disabled    0         000:00:00:00
3       0       Disabled    0         000:00:00:00
.
.
30      0       Disabled    0	000:00:00:00
 

If the -testnum argId is specified, then the configuration of that test only will be displayed. If the -testnum is not specified, then the configuration of all 30 tests will be displayed.

show delaytest status

Purpose

Shows the following status items for test or tests. Maximum tests on the system is 30 per blade.

• Test number (1 to 30).

• Endpoint ID of the test.

• Test state disabled/enabled.

• Test duration as configured by the last user (in seconds).

• Remaining seconds for the test---0 for disabled tests; 1 or greater for tests in progress.

• Minimum delay measured, given in milliseconds.

• Maximum delay measured, given in milliseconds.

• Average delay measured, given in milliseconds.

• ATM OAM loopback cells transmitted.

• ATM OAM loopback cells received in the correct order.

• ATM OAM loopback cells received out of order.

Options

Example

VCLI>>show delaytest status -sname tulsa1 -card 3 

Test Num
EPID 
Testing (secs)
Duration secs
Elapsed secs
Remain. time
Min. Dly
Max. Dly
Avg. Dly
Xmitted Cells
ExpectRcvd
Unexp.Rcvd

1
 0
Disabled
0
0
0
  0
0
0
0
0

2
 0
Disabled
0
0
0
  0
0
0
0
0

3
 0
Disabled
0
0
0
  0
0
0
0
0

.

.

.

30
0
Disabled
0
0
 0
  0
 0
0
0
0

show environment

Purpose

Shows the environment settings for the session.

Example

VCLI>>show environment
Autosave: Enabled	Timeout: Disabled	Page Limit: 0 lines*
SNMPTimeout: 5	 Provisioning Client Path:
Log Level: 4	Software Image Path:

show imccard config

Purpose

Shows the following configuration information about a card:

• Name string

• Location string

• Contact information string

• Switch IP address

Options

-network	Shows all IMC cards in the network
-sname SwitchName	Name of switch to display cards for

Example

VCLI>>show imccard config -sname tulsa1
Name: tulsa1_imc
Location: tulsa_pop_rack5_chassis2_slot2
Contact: Jose_Montoya_(772)555-1212
Switch IP address: 10.100.0.254

show imccard info

Purpose

Shows the following information about the IMC card:

• Software version

• Current date and time

• Part number

• Serial number

• CLEI Code

• Date of manufacture

• Hardware revision

• Card type

• Time (in seconds) since last reset

• Whether or not the card has currently active alarms

Options

-network	Shows all IMC cards in the network
-sname SwitchName	Name of switch to display card for

Example

VCLI>>show imccard info -sname tulsa1
Primary
Card Type: IMC
Software Version: Cisco, MGX 8240, Release 3.0.0.1
Current Date/Time: 07/12/99 23:33:07 GMT
Part Number: 205a000102revb   Serial Number: 0001a00134
CLEI Code: BATFHZ0DZZ         Date of Manufacture: 06/03/99
Fab Number: 312307	PCB Part Number:
MAC Address: 00:00:01:1a:0d:1c	Cisco Standard Card Type:
Address Status: Active
RMA Failure Code: 0	RMA History Code: 35
 
Backup
Software Version: Sentient Networks, MGX 8240, Release 3.0.0.1
Part Number: 205a000102revb   Serial Number: 0001a00134
CLEI Code: BATFHZ0DZZ         Date of Manufacture: 06/03/99
Fab Number: 312307	PCB Part Number:
MAC Address: 00:00:01:1a:0d:1d	Cisco Standard Card Type:
Access State: Active
Up Time: 33 days, 17:45.21 hours	Alarms: None

show imccard redundancy

Purpose

Shows the following redundancy configuration and status for each IMC card:

• Redundancy Role

• Redundancy State

If a backup card is present but not available, then cause of unavailability is shown.

Options

-network	Shows all IMC cards in the network
-sname SwitchName	Name of switch to display card for

Example

VCLI>>show imccard redundancy -sname tulsa1
IMC Card 1A (top)
Role: Backup		State: Unavailable, Self Failure
IMC Card 1B (bottom)
Role: Primary		State: Active

show logicalport atm config

Purpose

Shows the following about an ATM logical port:

• Admin Status (2 values---up, down)

• Identifier String

Options

-network	Shows every ATM BC in the network
-sname SwitchName	Name of switch containing the ATM BC
-card CardNum	Number of the card (2 to 16) containing the ATM BC

Example

VCLI>>show log atm config -sname tulsa1 -card 3
AdminSts: Up    Name: wc_993_er98

show logicalport atm statistics

Purpose

Shows the following ATM logical port statistics:

• Valid Cells Ingress

• Cells Ingress discarded due to HEC Errors

• Cells Egress

Options

-network	Shows every ATM BC in the network.
-sname SwitchName	Name of switch containing the ATM BC.
-card CardNum	Number of the card (2 to 16) containing the ATM BC.
-15m IntervalNum	Requests display of a requested 15-minute interval number. IntervalNum ranges from 0 to 2. 0 indicates current interval, 1 is previous 15-minute interval, 2 is the 2nd interval into the past.
-24h IntervalNum	Requests display of a requested 24-hour interval number. IntervalNum ranges from 0 to 1. 0 indicates current 24-hour interval. 1 is previous 24-hour interval. Default: 0.

Example

VCLI>>show log atm statistics -sname tulsa1 -card 3 -15m 0
OC3: 1         Current 15-minute Interval Elapsed Time (min:sec) 10:09
Valid Cells Ingress 0      Cells w/HEC Errors: 2,345
Cells Egress        0

show logicalport atm summary

Purpose

Shows the following information for the ATM logical port :

• Administrative status (up or down)

• Operational Status (up or down), if down, at least one of the following reasons are given:

  • Set administratively down

  • Physical Container down (If APS is enabled, protection switching failed)

• Out of Cell Delineation

• Number of configured VCCs

• Available Ingress Bandwidth (in Cells Per Second)

• Available Egress Bandwidth (in Cells Per Second)

Options

-network	Shows every ATM BC in the network
-sname SwitchName	Name of switch containing the ATM BC
-card CardNum	Number of the card (2 to 16) containing the ATM BC

Example

VCLI>>show log atm summary -sname tulsa1 -card 3
Admin Sts	Config VCCs	AvailIBW	AvailEBW	OperStatus	
Up	4	340000	340000	Phys
Down	Out
CellD

show physicalport ds0 allocation

Purpose

Shows how DS0 timeslots within a DS1 are allocated to CES connections. Connections are identified by their Endpoint ID (EPID).

Options

-network	Shows every DS1 port in the network
-sname SwitchName	Name of switch containing the DS1
-card CardNum	Number of the card (2 to 16) containing the DS1
-ds3 DS3Num	Number of the DS3 port containing the DS1
-ds1 DS1Num	Number of the DS1 port

Example

VCLI>>show ds0allocation -sname tulsa1 -card 3 -ds3 3 -ds1 1
DS0 Timeslot allocation by Endpoint ID (EPID) on DS3 3, DS1 1
DS0#	
EPID	
DS0#	EPID 	DS0#	EPID 	DS0#	EPID	DS0#	EPID
1	258	7 	0	13 	0	19	0	
 2	 259	8	 0	14	 0	20	0	
 3	 0	9	 0	15	 0	21	0	
 4	 0	10	0	16	0	22	0	
 5	 0	11	 0	17	 0	23	0
6	0	12	0	18	 0	24	0	

show physicalport ds1 bertconfig

Purpose

Shows the following BERT configuration information for the DS1 port:

• BERT Pattern (7 values---All Ones, 511, 2047, QRSS, 2²³-1, 3 In 24, User Configurable)

• User Pattern (hex number representing a 32 bit number)

• User Pattern Length (integer 1 to 32)

• Transmit Pattern Inversion (2 values---not inverted, inverted)

• Receive Pattern Inversion (2 values---not inverted, inverted)

• BERT Framing Mode (3 values---ESF, SF, Unframed)

• Run Control (2 values---running, stopped)

• Continuous Error Insertion (8 values---no errors, 10^-1, 10^-2, 10^-3, 10^-4, 10^-5, 10^-6, 10^-7)

Options

-network	Shows every DS1 port in the network
-sname SwitchName	Name of switch containing the DS1
-card CardNum	Number of the card (2 to 16) containing the DS1
-ds3 DS3Num	Number of the DS3 port containing the DS1
-ds1 DS1Num	Number of the DS1 port

Example

VCLI>>show phys ds1 bertconfig -sname tulsa1 -card 3 -ds3 1 -ds1 12
DS3: 1 DS1: 12 TestingState: Stopped Framing: ESF ErrorInsert: None
Pattern: QRSS        UserPattern: 0xAA55AA55 UserPatternLen: 32
TxPatternInvert: Off RxPatternInvert: Off 

show physicalport ds1 bertstatus

Purpose

Shows results of either a currently running BER test, or the last BER test. Statistics shown are

• Elapsed Test Time (seconds)

• Received Pattern Synchronization Status (2 values---in sync, loss of sync)

• Received Data/Pattern (32 bits displayed in hex)

• Percent Error Free Seconds---Displayed as % to 4 decimal places (for example, 100.0000%)

• Bit Error Rate---Represented as a string in scientific notation (for example, 1.23e-7)

• Number of Bit Errors

• Errored Seconds

• Severely Errored Seconds

• Pattern Loss Seconds

• Error Free Seconds

Options

-network	Shows every DS1 port in the network
-sname SwitchName	Name of switch containing the DS1
-card CardNum	Number of the card (2 to 16) containing the DS1
-ds3 DS3Num	Number of the DS3 port containing the DS1
-ds1 DS1Num	Number of the DS1 port

Example

VCLI>>show phys ds1 bertstatus -sname tulsa1 -card 3 -ds3 1 -ds1 12
DS3: 1 DS1: 12 TestingState: Stopped ElapsedTime: 01:34:58 BER: 1.23e-10
PatternSync: InSync      RxedPattern: 0xAA55AA55 BitErrors: 3
ErrorFreeSecs: 01:34:57 ErroredSecs: 00:00:01 SevErroredSecs: 00:00:00
PercentErrorFreeSecs: 99.2000%    PatternLossSecs: 00:00:00

show physicalport ds1 config

Purpose

Shows the following configuration information for the DS1 port:

Admin Status (3 values---up, down, test)

Channelization Mode (Channelized, Clear Channel)

Timing Mode (Internal, Through)

Framing Mode (ESF, SF, Other)

Line Coding (B8ZS, AMI)

Facilities Data Link (2 values---none, T1.403)

Bit-Oriented Send Code (3 values---None, Line Loop Request, Payload Loop Request)

Loopback Control (2 values---disabled, payload loop)

Identifier String

24 TCA Thresholds (integer)

Options

-network	Shows every DS1 port in the network
-sname SwitchName	Name of switch containing the DS1
-card CardNum	Number of the card (2 to 16) containing the DS1
-ds3 DS3Num	Number of the DS3 port containing the DS1
-ds1 DS1Num	Number of the DS1 port

Example

VCLI>>show phys ds1 config -sname tulsa1 -card 3 -ds3 1 -ds1 12
DS3: 1 DS1: 12 Name: WC2344_22s
Admin Status:   Up
Frame: ESF 	Timing: Internal 	Channelization: Channelized
Line Coding: B8ZS FDL: ANSI 	Loopback: None   Last Send Code: PayloadLoop
TCA Thresholds	NE 15 Min 	NE 24-hour	FE 15 Min 	FE 24-hour
Errored Secs	12 	121	12	121
Sev Err Secs 	10	100	10	100
Sev ERR Framing Secs	2	17	2	17
Unavailable Secs 	10 	10	10	10
Path Coding Violations 	14 	134 	14 	134
AIS Seconds	2	17		
Line Errored Secs 		12	21
Controlled Slip Secs	10	100	10	100
Out of Frame Events	72	691		

show physicalport ds1 statistics

Purpose

Shows statistics on DS1 port for the current 15-minute interval, one of the previous 32 15-minute intervals, the current 24-hour interval, or the previous 24-hour interval. Shows the following values:

• Errored Seconds

• Severely Errored Seconds

• Severely Errored Framing Seconds

• Unavailable Seconds

• Path Coding Violations

• Alarm Indication Signal Seconds

• Controlled Slip Seconds

• Out-of-Frame Events

• Far End Errored Seconds

• Far End Severely Errored Seconds

• Far End Severely Errored Framing Seconds

• Far End Path Coding Violations

• Far End Line Errored Seconds

• Far End Unavailable Seconds

• Far End Controlled Slip Seconds

Options

-network	Shows every DS1 port in the network.
-sname SwitchName	Name of switch containing the DS1.
-card CardNum	Number of the card (2 to 16) containing the DS1.
-ds3 DS3Num	Number of the DS3 port containing the DS1.
-ds1 DS1Num	Number of the DS1 port.
-15m IntervalNum	A 15-minute interval number. IntervalNum ranges from 0 to 32. 0 indicates current interval, 1 is previous 15-minute interval, 32 is the 32nd interval into the past.
-24h IntervalNum	Current 24-hour interval.

Example

VCLI>>show phys ds1 statistics -sname tulsa1 -card 3 -ds3 1 -ds1 12 -15m 0
	DS3: 1 	DS1: 12	Near End	Far End
Current Interval Elapsed Time (min:sec) 10:09
Errored Secs		463	453
Severely Errored Secs 		12	45522
Sev Err Framing Secs		123	4
Unavailable Secs	4432234	334455	
Path Coding Violations	1234567890	1234567890	
AIS Seconds	4444		
Controlled Slip Secs	5	7	
Line Errored Secs	21	2093
Line Code Violations	29
Out of Frame Events	21

show physicalport ds1 summary

Purpose

Shows the following information for a DS1 port:

• DS1 Framing (ESF, SF, Other)

• Timing Mode (Internal, Through)

• Channelization Mode (Channelized, Clear Channel)

• Line Coding (AMI, B8ZS) if containing DS3 has a managed M1:3 Multiplexor attached

• Admin Status

• Operational Status, including one or more of the following:

  • Set administratively down

  • Receiving Loss of Frame (LOF)

  • Receiving Alarm Indication Signal (AIS)

  • Receiving Yellow Alarm

  • Transmitting Yellow Alarm

  • Looping the received signal

  • Loss of Signal (LOS) if containing DS3 has a managed M1:3 Multiplexor attached

Options

-network	Shows every DS1 port in the network
-sname SwitchName	Name of switch containing the DS1
-card CardNum	Number of the card (2 to 16) containing the DS1
-ds3 DS3Num	Number of the DS3 port containing the DS1
-ds1 DS1Num	Number of the DS1 port

Example

VCLI>>show phys ds1 sum -sname tulsa1 -card 3 -ds3 1
DS3	DS1	Frame	Timing	Chan 	Coding	AdminSts	OperStatus
1	1	ESF	Int	Chan	B8ZS	Up	
1	2	Other 	Thru 	Clear 	AMI 	Up	LOF RcvAIS Rcv
							Yellow XmitYellow 
							DS3down
1	2	SF	Int	Clear	B8ZS	Down	AdminDown

show physicalport ds3 config

Purpose

Shows the following configuration information for the DS3 port:

• Admin Status (3 values---up, down, test)

• Line Type (2 values---M23, C-bit Parity)

• EAC Send Code (3 values---None, Line Loop Request, Payload Loop Request)

• Loopback Control (3 values---none, out, in)

• AIS to Yellow (2 values---enabled, disabled)

• Line Length (2 values---short, long)

• Identifier String

• 16 TCA Thresholds (integer)

Usage

Command will not work with Release 2.2 or earlier.

Option

-network	Shows every DS3 port in the network
-sname SwitchName	Name of switch containing the DS3
-card CardNum	Number of the card (2 to 16) containing the DS3
-ds3 DS3Num	Number of the DS3 port

Example

VCLI>>show phys ds3 config -sname tulsa1 -card 3 -ds3 1
DS3: 1 Name: WC2344_22s
Admin Status: Up   
Line Type: C-bit 	Line Length: Short
Loopback:    None   Last Send Code: PayloadLoop AIS to Yellow: Enabled
TCA Thresholds	NE 15 Min	NE 24-hour	FE 15 Min	FE 24-hour
Line Errored Secs	86	864		
Line Sev Errored Secs	4	40		
Line Coding Violations	387	3865		
Sev Err Framing Secs	2	8		
P-Bit Errored Secs	86	864		
P-Bit Sev Errored Secs	4	40		
P-Bit Coding Violations	382	3820		
C-Bit Errored Secs	86	864	86	864
C-Bit Sev Errored Secs	4	40	4	40
C-Bit Coding Violations	387	3820	387	3820	
Unavailable Secs	10	10	10	10	
AIS Secs	2	8		

show physicalport ds3 statistics

Purpose

Shows statistics on DS3 port for the current 15-minute interval, one of the previous 32 15-minute intervals, or the current 24-hour interval. Shows the following values:

• P-bit Errored Seconds

• P-bit Severely Errored Seconds

• P-bit Coding Violations

• Severely Errored Framing Seconds

• Line Errored

• Line Severely Errored Seconds

• Line Coding Violations

• Unavailable Seconds

• Alarm Indication Signal Seconds

• C-bit Errored Seconds

• C-bit Severely Errored Seconds

• C-bit Coding Violations

• Far End C-bit Errored Seconds

• Far End C-bit Severely Errored

• Far End C-bit Coding Violations

• Far End Unavailable Seconds

Options

Example

VCLI>>show phys ds3 statistics -sname tulsa1 -card 3 -ds3 2
DS3: 2     Current Interval Elapsed Time (min:sec) 10:09
	Near End	Far End
P-bit Errored Secs	4 	123
P-bit Severely Errored Secs 	4	123
P-bit Coding Violations 	4	123
Severely Errored Framing Secs	4	123
Line Errored Secs 	4	123
Line Severely Errored Secs	4	123
Line Coding Violations	4	123	
AIS Seconds	4	123
Unavailable Secs 	4	123	
C-bit Errored Secs 	4	123
 

show physicalport ds3 summary

Purpose

Shows the following information for a DS3 port:

• DS3 Line Type (M23, C-bit Parity)

• Admin Status (up, down, test)

• Operational Status, including one or more of the following:

  • Set administratively down

  • Receiving Loss of Signal (LOS)

  • Receiving Loss of Frame (LOF)

  • Receiving Alarm Indication Signal (AIS)

  • Receiving Yellow/Remote Alarm

  • Transmitting Yellow/Remote Alarm

  • Looping the received signal

  • Container down

Options

-network	Shows every DS3 port in the network
-sname SwitchName	Name of switch containing the DS3
-card CardNum	Number of the card (2 to 16) containing the DS3
-ds3 DS3Num	Number of the DS3 port

Example

VCLI>>show phys ds3 sum -sname tulsa1 -card 3

DS3	LineType	AdminSts	OperStatus
1	M23	Up	Up
2	C-Bit	Up	LOS LOF RcvAIS RcvYellow XmitYellow InLoop
3	C-Bit	Down	AdminDown

show physicalport oc3 config

Purpose

Shows the following configuration information for the OC3 port:

• Admin Status (3 values---up, down, test)---Applies to ports 1, 2, 3, and 4 independently

• Transmit Clock Source (2 values---local, loop)---Applies to both port pairs 1 and 2 and 3 and 4 simultaneously

• Cell Payload Scrambling (2 values---enabled, disabled)---Applies to both port pairs 1 and 2, and 3 and 4 simultaneously

• Loopback Control (3 values---none, out, in)---Applies to ports 1, 2, 3, and 4 independently

• Identifier String---Applies to ports 1, 2, 3, and 4 independently

• 22 TCA Thresholds (integer)

Options

-network	Shows every OC3 port in the network
-sname SwitchName	Name of switch containing the OC3
-card CardNum	Number of the card (2 to 16) containing the OC3
-oc3 OC3Num	Number of the OC3 port (1 to 4)

Example

VCLI>>show phys oc3 config -sname tulsa1 -card 3 -oc3 1
Admin Status: Up		Oper Status: Up
Transmit Clock Source:
Loop Loopback:	None	
Cell Payload Scrambling: Enabled
TCA Thresholds	NE 15 Min	NE 24-hour	FE 15 Min	FE 24-hour
Section Errored Secs	86	864
Section Sev Errored Secs	4	40
Section Sev Err Framing Secs	2	8
Section Coding Violations	387	3865
Line Errored Seconds	86	864	86	864
Line Sev Errored Secs	4	40	4	40
Line Coding Violations	387	3865	387	3865
Line Unavailable Secs	10	10	10	10
Line AIS Secs	2	8
Trunk Path #1
Path Errored Secs	86	864	86	864
Path Sev Errored Secs	4	40	4	40
Path Coding Violations	387	3865	387	3865
Path Unavailable Secs	10	10	10	10
Path AIS Secs	2	10

show physicalport oc3 statistics

Purpose

Shows statistics on OC3 port for the current 15-minute interval, one of the previous 32 15-minute intervals, or the current 24-hour interval, or the previous 24-hour interval. Shows the following values:

• Section Errored Seconds

• Section Severely Errored Seconds

• Section Severely Errored Framing Seconds

• Section Coding Violations

• Line Errored Seconds

• Line Severely Errored Seconds

• Line Coding Violations

• Line Unavailable Seconds

• Line Alarm Indication Signal Seconds

• Far End Line Errored Seconds

• Far End Line Severely Errored Seconds

• Far End Line Coding Violations

• Far End Line Unavailable Seconds

• Path Errored Seconds

• Path Severely Errored Seconds

• Path Coding Violations

• Path Unavailable Seconds

• Path Alarm Indication Signal Seconds

• Far End Path Errored Seconds

• Far End Path Severely Errored Seconds

• Far End Path Coding Violations

• Far End Path Unavailable Seconds

Options

-network	Shows every OC3 port in the network
-sname SwitchName	Name of switch containing the OC3
-card CardNum	Number of the card (2 to 16) containing the OC3
-oc3 OC3Num	Number of the OC3 port (1 to 4)
-15m IntervalNum	Requests display of a requested 15-minute interval number. IntervalNum ranges from 0 to 32. 0 indicates current interval, 1 is previous 15-minute interval, 32 is the 32nd interval into the past.
-24h IntervalNum	Requests display of a requested 24-hour interval number. IntervalNum ranges from 0 to 1. 0 indicates the current 24-hour interval. 1 indicates the previous 24-hour interval.

Example

VCLI>>show phys oc3 statistics -sname tulsa1 -card 3 -oc3 1 -15m 0
Switch Name: tulsa1, Card: 3
OC3: 1           Current Interval Elapsed Time (min:sec) 14:05
	Near End		Far End
Section Errored Secs	0
Section Severely Errored Secs	0
Section Sev Err Framing Secs	0
Section Coding Violations	0
Line Errored Seconds	0	0
Line Severely Errored Secs	0	0
Line Coding Violations	0	0
Line Unavailable Secs	0	0
Line AIS Secs	0	0
Trunk Path #1
Path Errored Secs	0	0
Path Severely Errored Secs	0	0
Path Coding Violations	0	0
Path Unavailable Secs	0	0
Path AIS Secs	0

show physicalport oc3 summary

Purpose

Shows the following information for an OC3c port:

• Admin Status

• ATM cell payload scrambling

• OC3 transmit clock source

• Operational Status, including one or more of the following:

  • Set administratively down

  • Section Loss of Signal (LOS)

  • Section Loss of Frame (LOF)

  • Line Alarm Indication Signal (AIS) received

  • Line Remote Defect Indication (RDI) received

  • Path STS Loss of Pointer (LOP)

  • Path STS Alarm Indication Signal (AIS) received

  • Path STS Remote Defect Indication (RDI) received

  • Path Signal Label Mismatch

Options

-network	Shows every OC3 port in the network
-sname SwitchName	Name of switch containing the OC3 port
-card CardNum	Number of the card (2 to 16) containing the OC3 port
-oc3 OC3Num	Number of the OC3 port (1 to 4)

Example

VCLI>>show phys oc3 sum -sname tulsa1 -card 3
 

OC3
Side
TxClk
CellScrm
AdminSts
OperStatus

1
Trunk
Loop
Enabled
Up
SctnLOS SctnLOF LineAIS PathLOP PathAIS 

2
Trunk
Local
Disabled
Test
InLoop  LineRDI PathRDI LabelMis

3
Access
Local
NA
 Up
 No Alarm

4
Access
Local
NA
 Down
No Alarm

Access Side SonetPath

SonetPath #
 
Operational State
 

1
PathLOP, PathAIS
 

2
No Alarm
 

3
PathLOP, PathAIS
 

show switch redundancy

Purpose

Shows all redundancy groups within a switch, and the redundancy role and status of each card.

The following abbreviations are used for the redundancy role:

P = Primary

B = Backup

N = None (neither primary nor backup)

UNK = Unknown

- = No card

The following abbreviations are used for the redundancy state:

NR = non-redundant

SB = Standby

F = Failed

SI = Switched-in

SO = Switched-out

SIP = Switch-in In Progress

FBP = Force Back InProgress

UNP = Unprotected

PRO = Protected

UNK = unknown

Options

-network	Shows all switches in the network
-sname SwitchName	Name of switch to display redundancy information for

Example

VCLI>>show switch redundancy -sname tulsa1
Phys Slot	1A	1B	2	3	 4	5	6	 7	 8	 9	10	11	12	13	14	15	16
Group	-	-	-1	1	2	2	2	2	2	7	7	0	7	7	0	UNK 	UNK
Role	-	-	P	B	B	P	P	P	P	B	P	N	P	P	N	UNK	UNK
State	-	-	PRO	SB	SB	PRO	PRO	PRO	PRO	SI	PRO	NR	SO	PRO	NR	UNK	UNK
Log Slot	-	-	 1	1		3	4		6	10	8	9	10	11	12	UNK 		-

show switch sntp config

Purpose

Shows sntp configuration, including the following:

• Client operating mode (there are 3 values---multicast, anycast, and unicast). Only unicast is supported with Release 3.0.)

• Primary server IP address (IP adress of primary sntp server)

• Secondary server IP address (IP address of the secondary sntp server, used only if primary doesn't respond)

• Time correction (10 values---1 to 10%. Percentage of time correction allowed for client's clock for every poll from the server)

• Server timeout (in seconds before communication down is declared)

• Protocal admin status (2 values---enable, disable)

• Time between polls (range 60 to 86400 seconds)

• Number of sameple from server until time adjustment starts (range 1 to 7)

Options

-network	Shows sntp configuration for all cards in network
-sname Switch Name	Name of switch to show card sntp configuration for
-card CardNum	Number of card (2 to 16) to show sntp configuration for [optional]
-cardtype all | imc | ces	Type of card to show config for (all cards, IMC cards, or CES cards)

Example

VCLI>>show switch sntp config-sname tulsa1-card 3
Switch Name: tulsa1, Card:3
Operation Mode: Unicast	 Time Correction: 3 	Server Timeout: 60
Primary Server IP Address: 100.12.14.3		Secondary Server IP Address: 100.12.14.2
Admin Status: Enabled	Polling Period: 534	Number of Samples:5

show switch sntp status

Purpose

Shows sntp status, including the following:

• Client version (4 values---1 to 4. Release 3.0 supports only value 4.)

• Server Version (4 values---1 to 4)

• Server Stratum (range 1 to 14)

• Time last sntp request was transmitted

• Time last sntp request was received

• Destination time (0 means no communication was established)

• Roundtrip Delay (0 means no delay)

• Clock Offset between card and server

• IP address of the last successfully reached server

Options

-network	Shows sntp configuration for all cards and switches in the network
-sname SwitchName	Name of switch to show the card sntp configuration for
-card CardNum	Number of the card (2 to 16) to show sntp configuration for (optional)
-cardtype all | imc | ces	Type of card to show config for (all cards, IMC cards, or CES cards)

Example

VCLI>>show switch sntp stat -sname tulsa1 -card3
Switch Name: tulsa 1, Card: 3
Client Version: 4	Server Version: 2	Server Stratum: 12
Last Originate Time: 01/01/00 01:01:01
Last Transmit Time:01/01/00 01:01:01
Last Receive Time: 01/01/00 01:01:02
Destination Time: 01/01/00 01:01:02
Roundtrip Delay: 4
Clock Offset: 0
Last Reached Server: 171.13.15.64

show switch summary

Purpose

Shows the following information about cards in the switch:

• Card type

• Card status

• Card redundancy role

• Card redundancy group

• Card switched in for

• Card software version

• PCB serial number

• Pcb rev number

• In-band IP address

• Interface Preference

• I/O card Type

• I/O PCB rev Number

• I/O Card State

• Data State

Options

-network	Shows all cards in the network
-sname SwitchName	Name of switch to display cards for
-card CardNum	Number of the card (2 to 16) to display information for

Example

VCLI>>show switch summary -sname tulsa1 -card 5
Switch Name: tulsa1, Card: 5
Data State: Current			Software Version: 3.0.0.1
Card Type: CS3 	Card Status: Active
Redundancy Role: Primary 	Redundancy State: Protected
Redundancy Group: 2
PCB Serial Number:	PCB Rev Number:
Inband IP address: 10.128.43.5 	Interface Preference: OOBand
I/O Card Type: 4 OC#s	I/O Card PCB serial Number:
I/O Card PCB Rev Number: 	I/O Card State: Active

show system operator

Purpose

Shows the following information about all operators configured to use the VCLI system:

• Operator Name

• Privilege Level

Options

Command does not have options.

Example

VCLI>>show system operator
Operator Name			Privilege Level
atjones		Admin
jdsmith	Change
wallym	Show

show system status

Purpose

Shows the status of the in-band and out-of-band interfaces that the VCLI string is using. The following information is shown:

• In-band IP Address status

• Out-of-band IP Address status

Options

-network	Shows all CES cards in the network
-sname SwitchName	Name of the switch containing the card(s) to show

Example

VCLI>>show system status -sname tulsa3
Phys Slot	1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16
In-Band	NA	U	U	D	U	U	NA	U	U	U	D	U	U	U	U	U
Out-of-Band	U	U	U	D	U	U	NA	U	U	U	U	U	U	U	U	U
Current Xface	O	I	I	NA	I	I	NA	I	I	O	I	I	I	I	I	I
 

This command does not communicate with the switch to ascertain addresses; the information is from the internal database of the VCLI.

If a card is not in the switch database, the status and the Current Xface lines show NA. If the VCLI knows an interface to be up, a U is displayed. If the VCLI knows an interface to be down, a D is displayed. The current xface line shows the interface that the VCLI is currently using to communication with the card: I for ---, O for out-of-band.

show system switch

Purpose

Shows the following configuration information for a switch or all switches:

• Out-of-band IP Address

• Community String

• List of cards configured to be within this switch

Usage

This command requires admin status.

Options

-network	Shows all switches in the network
-sname SwitchName	Name of the switch to show

Example

VCLI>>show system switch -sname tulsa1
Switch Name: tulsa1
Out-of-band IP Address: 206.14.150.201 Community String: borg19e
Configured Cards: 2 3 4 5 6 7 8 9 10 11 12 13 14 15

show version