cc/td/doc/product/wanbu
hometocprevnextglossaryfeedbacksearchhelp
PDF

Table of Contents

9.2.34 Version Software Release Notes
Cisco WAN Switching System Software

9.2.34 Version Software Release Notes
Cisco WAN Switching System Software

About These Release Notes

Cisco documentation and additional literature are available in a CD-ROM package, which ships with your product. The Documentation CD-ROM, a member of the Cisco Connection Family, is updated monthly. Therefore, it might be more current than printed documentation. To order additional copies of the Documentation CD-ROM, contact your local sales representative or call customer service. The CD-ROM package is available as a single package or as an annual subscription. You can also access Cisco documentation on the World Wide Web at http://www.cisco.com, http://www-china.cisco.com, or http://www-europe.cisco.com.

If you are reading Cisco product documentation on the World Wide Web, you can submit comments electronically. Click Feedback in the toolbar, select Documentation, and click Enter the feedback form. After you complete the form, click Submit to send it to Cisco. We appreciate your comments.

About the 9.2 Release

The 9.2 software release supports the Cisco WAN switching products, BPX 8600 series, and IGX 8400 series. This release does not support the IPX switch.

Phased Release Strategy

The MSSBU rollout plans for the 9.2 release is based upon a series of incremental feature releases. This phased feature release strategy is designed to allow the earliest customer availability of key new features, consistent with maintaining high product quality. For the latest status of each 9.2 feature, please see below.

The minimum release version noted in the table below represents the minimum switch software version required for each feature. As usual, it is recommended that customers use the most current maintenance releases.

Definitions

Generally Available (GA)--Feature is ready for wide deployment with no restrictions. Customers deploying GA features are supported by the Technical Assistance Center (TAC).

First Customer Ship (FCS)--Feature is available for controlled introduction by selected customers. To trial use an FCS feature, please contact your account representative.

Customers selected for controlled introduction will receive assistance with test plan review and special support from the New Product Team (NPT) in addition to the normal Technical Assistance Center (TAC) support.

Pre-First Customer Ship (Pre-FCS)--Feature is not yet available in the Switch Software baseline.

Target Date--This is the date for feature delivery that is supported by current Engineering and Marketing plans. This date is subject to change.

Product

Feature Name

FCS/GA
Status

Minimum Release

 IGX


 Support for UXM XLR card


 GA


 9.2.30


 BPX 


 Support Multiple VSI Partitions


 FCS


 9.2.30


 IGX


 HDM/LDM Control Lead Trap


 FCS


 9.2.30


 IGX


 Support UXM Feeder


 FCS


 9.2.30


 IGX


 SES Feeder to IGX


 GA


 9.2.23


 BPX


 Include SONET line protection: APS on BXM-OC3 and BXM-OC12 (1+1)


 FCS


 9.2.20


 BPX


 Include SONET line protection: APS on BXM-OC3 and BXM-OC12 (2 card, 1:1)


 FCS


 9.2.20


 BPX


 Support for 16K connections


 GA


 9.2.20


 BPX


 Support for LMI/ILMI on BXM card


 GA


 9.2.20


 BPX


 Support for Virtual Trunking on the BXM card


 GA


 9.2.20


 BPX


 Support for Virtual Switch Interface (VSI) 2.2


 GA


 This interface is available in 9.2.20. Use of this interface is dependent upon other products, for example IOS.


 BPX/IGX


 A-bit Notification


 GA


 9.2.20


 BPX/IGX


 Alarms for all service-affecting events


 GA


 9.2.20


 BPX/IGX


 Support for feature mismatch on BXM and UXM cards


 GA


 9.2.20


 BPX/IGX


 Support for Hitless Rebuild including Disable Auto Bus Diagnostics


 GA


 9.2.20


 BPX/IGX


 Support for IGX and BPX trunk reconfiguration without outage


 GA


 9.2.20


 BPX/IGX


 Support for Revision Interoperability between 9.1 and 9.2 


 GA


 9.2.20


 BPX/IGX


 Support for UXM and BXM Multilevel Channel Statistics


 GA


 9.2.20


 BPX/IGX


 Support ports and trunks on the same UXM and BXM cards


 GA


 9.2.20


 IGX


 Support for ATM Forum Standard Compliant IMA Trunking with UXM Firmware Model B


 GA


 9.2.20


 IGX


 Support for Virtual Trunking on the UXM card


 GA


 9.2.20


 IGX


 Support VC traffic shaping on UXM port 


 GA


 9.2.20


 BPX


 Support for APS Annex B


 FCS


 9.2.20


 BPX/IGX


 Real-Time VBR


 FCS


 9.2.20


 IGX


 Support Enhanced UXM (GA)


 GA


 9.2.20


 IGX


 Support for Idle code suppression for video on UVM and CVM cards


 GA


 9.2.20


 IGX


 Support for UXM VP tunneling


 FCS


 9.2.20

Software Release 9.2.34

This is a maintenance release including all features supported up to Release 9.2.30. The following files will be extracted from a TAR file upon upgrading to Software Release 9.2.34.


Table 1: Release 9.2.34 Files
File Name File Size

9234B.000

65536

9234B.001

65536

9234B.002

65536

9234B.003

65536

9234B.004

65536

9234B.005

65536

9234B.006

65536

9234B.007

65536

9234B.008

65536

9234B.009

65536

9234B.010

65536

9234B.011

65536

9234B.012

65536

9234B.013

65536

9234B.014

65536

9234B.015

65536

9234B.016

65536

9234B.017

65536

9234B.018

65536

9234B.019

65536

9234B.020

65536

9234B.021

65536

9234B.022

65536

9234B.023

65536

9234B.024

36752

9234B.img

784

9234G.000

65536

9234G.001

65536

9234G.002

65536

9234G.003

65536

9234G.004

65536

9234G.005

65536

9234G.006

65536

9234G.007

65536

9234G.008

65536

9234G.009

65536

9234G.010

65536

9234G.011

65536

9234G.012

65536

9234G.013

65536

9234G.014

65536

9234G.015

65536

9234G.016

65536

9234G.017

65536

9234G.018

65536

9234G.019

65536

9234G.020

65536

9234G.021

65536

9234G.022

65536

9234G.023

65536

9234G.024

65536

9234G.025

65536

9234G.026

52206

9234G.img

784

Software Release 9.2.31, 9.2.32, 9.2.33

This is a maintenance release including all features supported up to Release 9.2.30.

Software Release 9.2.30

Includes all features supported up to Release 9.2.20 and introduces the following additional features:

Software Release 9.2.23, 9.2.22, and 9.2.21

Includes all features supported up to Release 9.2.20.

Software Release 9.2.20

Includes all features supported up to Release 9.2.10 and introduces the following additional features:

Software Release 9.2.10

Includes all features supported up to Release 9.2.01 and introduces the following additional features:

Software Release 9.2.01

Includes all features supported in Release 9.2.00 and introducing the following additional features:

Software Release 9.2.00

Introduces the following features:

Clarifications

    1. Release 9.2.31 introduced a new command--cnffdrlmiparms--which makes the feeder LMI timers and counters configurable. This command is currently supported on BPX only and cannot be added in the Job mode.

Usage: cnffdrlmiparms slot.port T393 T394 T396 N394 N395
where slot.port specifies the feeder trunk to configure. The details of the other parameters are as follows:

Timer

Description

Range (sec.)

Default (sec.)

 T396


 LMI polling timer


 5-30


 10


 T393


 SPC STATUS ENQUIRY timer


 5-30


 10


 T394 


 SPC UPDATE STATUS timer 


 5-30 


 10


 N394


 Max retry count for SPC STATUS 


 ENQUIRY/ REPORT procedures


 1-10


 5


 N395


 Max retry count for SPC UPDATE


 STATUS / ACK procedures


  1 -10


 5

    2. In Release 9.2.31 the system parameter 2 (cnfsysparm 2) is changed from "Fail Connections On Communication Break" to "Allow CPU Starvation of Fail Handler."

The old parameter has been removed as it violated the principle of the separating control and data plane. The new parameter allows a new feature to be turned off, which gives CPU to the Fail Handler at the expense of the Transaction Handler in case the Fail Handler does not get scheduled for a long time.

    3. Do not mix MEE and MEF (or higher) in Y-red pairs for BXM 2-port group enhanced cards (OC-3 or OC-12 port). Addyred will fail if both are in standby mode, or the primary card has been activated with MEF (or higher) and the secondary card has MEE.

    4. For the BXM 2-port group, enhanced cards activated with MEF or higher, downrev to MEE will bring the cards into MISMATCH mode. This applies to both single cards and Y-red pairs.

    5. Release 9.2.30 introduced four new commands in BPX:

    6. There are changes in the following command starting from Release 9.2.30:

    7. The multiple partitions introduce two VSI partitions on trunk and port interfaces on the BXM card. One partition can be used for MPLS, and one can be used for PNNI. Virtual Trunk can have only one VSI partition or can be used for AutoRoute, but cannot be used for both VSI and AutoRoute simultaneously. This project introduces six service class templates in addition to the three existing templates.

Even though tag ABR is supported in Service Class Template (SCT), neither the MPLS controller nor the BXM firmware currently support this.
The configurable VPI/VCI introduces 2 new parameters in addctrlr and addshelf commands, through which the user can specify the VPI and VCI of the master-slave control channels.

    8. There is a change in reporting of port group numbers in Release 9.2.32. Previous image (MEC) of BXM used to report a 1-port group for the 2-port group cards at the channel statistics level 2 and 3. This made the port belonging to second port group unusable.

Upgrading to 9.2.30 software first and then burning the BXM card with the MED firmware, BXM will report 2-port groups for 2-port cards all the time. The smooth transition between the earlier 1-port group and the newly reported 2-port groups also displays the message in dspcd "Inconsistency with logical PG #" (port group number). All earlier software will "mismatch" the card.
If the BXM card is programmed with MEC or earlier firmware revision, the channel statistics are level 2 or 3 will report 1-port group. Burning an MED image will result in 2-port groups, but for backward compatibility the software will not do the recomputation of LCNs based on the new port groups. In its logical database, this will not impact the AutoRoute connections.
For VSI controllers the reported value will be higher than the actual available LCNs. That means a VSI controller may not be able to add connection even though the available connections are non-zero. If the user wishes to remove the above discrepancy, the card must be brought to the standby mode.
Note that the newly configured card or the card in standby mode programmed with MED image brought to the active state will not have above discrepancy.

    9. In BPX nodes that use processor cards with 32 MB of RAM, it is possible to run out of memory in the Hitless Region. This can happen if the node is too heavily configured with cards and connections. The recommendation below should prevent memory aborts.

In nodes that have processor cards with 64 MB of RAM, there should be no Hitless Region memory problem. This is because 64 MB processors contain a second Hitless Region, which is larger than the first.
The following calculation will help prevent memory aborts on BPX processors with 32 MB. For simplicity, the numbers are approximate. It is necessary to add up the number of cards in the node, as well as the number of connections, and make sure that the total does not exceed the recommendation.
During system initialization, roughly 17,100 blocks of the available 40,000 are used for the card database.
In addition, assume that 1500 blocks will be needed for each BXM card that can support 16K connections, which is the more common configuration. Some BXM cards can support 32K connections, and these will need 3000 blocks of the Hitless Region. This chunk of memory is allocated at the insertion of the BXM card and will not be released until a card of different card type is inserted.
Also, 300 blocks will be needed for each 1000 via connections on the node. This can be viewed with the user command dspload.
    17100 blocks for card database
    1500 blocks for EACH BXM that supports 16K conns 
    3000 blocks for EACH BXM that supports 32K conns 
     300 blocks for EACH 1000 conns
   -----------------------------------------------------------------
   40000 blocks maximum total (34000 blocks for 9.2 releases up to 9.2.23)

    10. The minimum software required to run MPLS are:

The BPX with an external 7x00 label switch controller (router) with Switch Software Release 9.2.10 and IOS Release 12.0(5)T can function as an ATM-LSR. The enhancements to dynamic label switching that was supported in Release 9.1 include support for MPLS Class of Service. The BPX as an ATM-LSR supports the "Multi-Label VC" model to support MPLS Class of Service. Five Qbins (Qbin 10-14) are reserved for MPLS Class of Service. Class-based WFQ is supported on these IP queues.
The BPX can also function as a "P" ATM-LSR in the MPLS-VPN architecture.
Hot redundancy of MPLS connections on the BPX is supported by BXM hot card redundancy. Continuous message forwarding, and keep-alive between the BXM redundant pair ensures the connection continuity on BXM switchover. On failure of a BXM card, the standby card becomes active with the label VCs. Resynchronization between the MPLS label switch controller and the BPX ensures that their databases are in sync.

    11. The 16K connections feature increases the number of connections terminating on the BPX switch to 16,000. The count includes connections terminating on BXM or ASI endpoints on cards within the node as well as connections terminating on service modules in the feeder shelves connected to the BPX switch. For example, a Frame Relay connection that originates on an FRSM in an MGX 8220 connected to a BPX counts as one of the 16,000 terminated connections on that BPX.

This feature requires a BCC-3-64 or BCC-4 controller in the BPX as well as Switch Software 9.2.10 or higher.

    12. Version 2.2 of the Virtual Switch Interface (VSI) provides the BPX switch with the ability to support multiple network protocols and multiple controllers per switch (for example, MPLS, PNNI, and so on). Switch resources can be dedicated to a specific controller or shared by multiple controllers.

This feature is supported on BXM ports, trunks, and virtual trunks and requires a BCC-3-64 or BCC-4 controller in the BPX as well as Switch Software 9.2.10 or higher and firmware MEA or higher.
Following are the VSI features:

    13. The combinations of system limits such as the number of trunks, lines, ports, and connections as well as enabled TFTP interval statistics should be provisioned so that the node has at least 50 percent idle time usage. Use the command dspprfhist to verify.

    14. When cost-based routing is used, increasing the cost of a trunk will result in deleting the preferred path on connections in the database if the sum of the preferred path cost exceeds the connection of configured cost. The connections will remain routed on its current path.

    15. On the BXM and UXM, for the OC-3 MultiMode Fiber back cards, Y-Redundancy/hot standby is not supported due to hardware restrictions.

    16. The trunk reconfiguration feature does not support IMA trunks.

    17. HDM to UVM interworking for Nx64K connections is not supported in this release.

Special Installation/Upgrade Requirements

General/Upgrade Procedure

Please consult your Support Representative before performing any software upgrade.

    1. The earliest release supported for graceful upgrade is 9.1.03.

    2. The 9.2 switch software requires MEH or MFD BXM firmware.

    3. Before upgrading to this release when UXM cards are to be used, certain legacy card firmware must be upgraded. See the compatibility matrix for cards affected and the exact versions to be used.

Note   Standards-compliant IMA is not compatible with the proprietary IMA protocol used in revision A firmware. Both ends of an IMA trunk must have the same protocol.
Caution Failure to follow this procedure may result in the card not operating. The card should be returned to Cisco if this occurs:
Step 1   Verify current boot code version

In order to run Model B firmware on UXM, the card needs to be running boot code revision 6 or greater. To determine the boot code running on the card, issue the following command from CLI (user must be logged in as Service level or greater to use this command):

rsh <slot #> sys version

Step 2   Upgrade UXM's boot code if necessary

The process for loading boot code is identical to the process you would use to load firmware. The only part that changes is the name of the file.

Note   Burning the boot code will cause the card to reset.

Step 3   Upgrade UXM's firmware

Step 4   When Y-redundant trunks are used, the red alarm in/out values must be configured to 1.25/1.5 seconds or greater, or else INVMUX failures will occur and trunk failures will be observed during a Y-redundancy switchover. Use the following command:

cnftrkparm

This is due to the IMA protocol and may cause reroute of connections.

Step 5   Upgrade NPM software to 9.2

    4. Procedure for upgrading UXM-to-IMATM trunks from proprietary IMA protocol to ATM forum-compliant IMA protocol.

Step 1   Download and burn UXM bootcode version 6 or later to all UXMs in the network. This will cause the card to reset and reroute traffic to other trunks.

Step 2   On IGX, to have firmware upgrade, issue command cnffunc 15 d to disable the UXM from resetting automatically after the firmware is burned in.

Step 3   On each MGX 8220 equipped with IMATM-B, upgrade the ASC to 5.0.10.

Step 4   Download the Forum Compliant Firmware Version IMATM5.0.10.fw but do NOT reset the IMATM-B card.

Step 5   On each IGX-UXM with IMA to be upgraded, burn firmware ABE or later to each UXM with IMA trunks.

Step 6   Simultaneously reset the card at each end of each IMA trunk to minimize trunk outage.

Step 7   Upgrade 9.1 nodes to 9.2 via loadrev and runrev.

Step 8   Issue the command cnffunc 15 e after each IGX is upgraded to 9.2.20 or later.

Note   The above procedure also applies to the UXME.

    5. Procedure for upgrading UXM-to-UXM trunks from proprietary IMA protocol to ATM forum-compliant IMA protocol.

Note   For Y-redundant UXMs, issue the command cnftrkparm 18 100000 100000 prior to this procedure and return to default values after this procedure.
Step 1   Download and burn UXM bootcode version 6 or later to all UXMs in the network. This will cause the card to reset and reroute traffic to other trunks.

Step 2   On IGX to have firmware upgraded, issue command cnffunc 15 d to disable the UXM from resetting automatically after the firmware is burned in.

Step 3   On each IGX-UXM with IMA to be upgraded, burn firmware ABE or later to each UXM with IMA trunks.

Step 4   Simultaneously reset the card at each end of each IMA trunk to minimize trunk outage.

Step 5   Upgrade 9.1 nodes to 9.2 via loadrev and runrev.

Step 6   Issue the command cnffunc 15 e after each IGX is upgraded to 9.2.20 or later.

Note   The above procedure also applies to the UXME.

    6. Procedure for upgrading BXM cards to the 9.2 firmware release.

To enable BXM cards to utilize 9.2 features, all BXM cards must be upgraded to the 9.2 firmware release. The following steps should be taken to avoid card mismatch:

For the switch running

Perform the following steps to avoid card mismatch:

Step 1   Upgrade BXM firmware to MEB.

Step 2   Upgrade BCC software to 9.2.30 or higher.

Step 3   Upgrade BXM firmware to MEH.

For all other cases, do the following steps:

Step 1   Upgrade BXM firmware to MEH.

Step 2   Upgrade BCC software to 9.2.30 or higher.

Note    See the Compatibility Matrix for the exact versions to be used.

    7. Procedure for adding new BCC cards as a part of upgrading to the 9.2 release.

Note   See the Compatibility Matrix for the tested/supported versions of other firmware and software that work with this release.

    8. Upgrading VSI 1.1 in Release 9.1 to VSI 2.2 in Release 9.2.

Step 1   Upgrade the Tag Switch Controller (TSC)

The TSC is upgraded to the CoS VSI Version Capable Release (IOS 12.XX). This image is VSI bilingual, meaning it understands both VSI Version 1 and Version 2.

Step 2   Upgrade the BXMs

All the BXM cards in the node are upgraded to Revision E, which is VSI Version 2 and CoS capable. After each BXM card is downloaded with the Revision E image, it temporarily experiences VSI outage until the BCC software is upgraded to the 9.2.34 image. The VSI outage during the upgrade is caused by the Revision E firmware not being backward compatible with VSI Version 1 features.

Note that from the TSC perspective, after a BXM is upgraded to the Revision E image, the interfaces that used to be on the card will "disappear." The TDP sessions that were on the interfaces will be lost. When all the BXMs are upgraded to the Revision E while still running Release 9.1 software on the BCC, the node will experience a complete outage of MPLS traffic. AutoRoute will have a hitless upgrade.

Step 3   Upgrade the BCC.

As the BCC is upgraded from software Release 9.1 to Release 9.2.34, the BCC recognizes the Revision E BXMs and downloads the VSI partition configuration. This causes the BXMs to issue ifc cfg traps to the TSC, allowing the TSC to rediscover all the MPLS interfaces on the BPX. The TDP sessions are reestablished and MPLS traffic starts flowing again through the BPX.

Note   The VSI 1.1 and VSI 2.2 are not interoperable.

Revision Interoperability Supported

Revision interoperating upgrades are supported, from the 9.1 to 9.2 releases of Switch software, with secondary revision incorporation for network lowest revision. This will lessen the risk of new features being enabled in a mixed network after the downgrade.

A "Secondary Revision" field in the node is used for the determination of the network lowest revision. Previous to this change, software used only the nodes primary revision.

The interoperability functionality uses network lowest revision for:

Version Compatibility Notes

For a complete list of firmware revisions supported, see the Compatibility Matrix document, which is included in this release package.

Control Card Requirements

All processor cards must be configured with a minimum of 32MB of RAM. This includes BCCs and NPMs. NPMs require at least 1MB of BRAM. To verify the BRAM size on IGX 8400 nodes, use the dspcd command.

Note   If any control cards contain less than 32MB of DRAM (these would be NPMs) then they must be replaced with cards containing at least 32MB of DRAM prior to upgrading to Release 9.2. The physical upgrade of the nodes with these control cards must be done according to the upgrade procedure defined as follows.

Control Card Boot Firmware Requirements

As specified next, the correct version of control card (CC) boot firmware must be installed on the cards prior to a software upgrade to Release 9.2.

BCC Type

Firmware

 BCC-32


 H.B.J


 BCC-3-32


 H.C.M


 BCC-3-64


 H.D.M


 BCC-4V


 H.H.M



NPM Type

Firmware

 NPM-32


 R.B.S


 NPM-64


 R.C.S


 NPM-32B


 R.E.S


 NPM-64B


 R.F.S

With the new version of NPM boot code (RXS), the boot code upgrading does not require physical card resetting with the following steps:

Step 1   Burn the boot code on the active NPM (1).

Step 2   Execute the switchcc command and wait until the NPM(1) becomes standby. NPM(2) is now active.

Step 3   Execute the resetcd command to reset the standby (resetcd 1 h). Wait until the reset card NPM(1) becomes standby.

Step 4   Burn the boot code on the active NPM(2).

Step 5   Execute the switchcc command and wait until the NPM(2) becomes standby. NPM(1) is now active.

Step 6   Execute the resetcd command to reset the standby (resetcd 2 h). Wait until the reset card NPM(2) become standby.

Control Card Compatibility Requirements

Each redundant pair of BCC cards in a given BPX 8600 node must be of the identical type and memory configuration. That is, for example, if the active card is a BCC-3-32, then so must be the standby. BCC-3 cards with 32MB of RAM cannot be mixed with BCC-3 cards with 64MB of RAM.

Each redundant pair of NPM cards in a given IGX 8400 node must be of the identical type and memory configuration. That is, for example, if the active card is an NPM-32, then so must be the standby. NPM cards with 32MB of RAM cannot be mixed with NPM cards with 64MB of RAM. Also, NPM-64 cards cannot be mixed with NPM-64B cards.

This is a requirement for all software upgrade and downgrade procedures. It does not apply to the physical card upgrade procedure, described in the following section.

Control Card Physical Card Upgrade Procedure

When performing a control card (CC) upgrade, the following procedure must be used. This applies to all processors: BCCs, and/or NPMs.

Step 1   Remove the current standby CC front and back card. (Remove back card only applies to BCC.)

Step 2   Replace with new CC front and back cards. (Replace back card only apply to BCC.)

Step 3   Wait for the standby updates on the newly installed standby CC to complete.

Step 4   Issue a switchcc command to utilize the newly installed CC.

Step 5   Verify that the network is stable.

Step 6   Remove the current standby CC front and back card. (Remove back card only applies to BCC.)

Step 7   Replace with new CC front and back cards that are identical to the current active CC. (Replace back card only apply to BCC)

Step 8   Wait for the standby updates on the newly installed standby CC to complete.

Step 9   The CC physical upgrade is now complete.

Step 10   With the secondary card in the standby state, cause a switchover using the switchcc command. This will test that the hardware is working correctly.

Note   After Step 2, the node will contain a mix of an old type CCs and the new type CCs. This condition is permitted only while the standby updates to the new CC are in progress, which will take less than one hour. The time during which this mixture of CC types exists must be kept to a minimum by immediately replacing the second old type CC with the matching one of the new type.

Obsoleted

Notes and Cautions

Additional Notes:

    1. Switch Software Release 9.2 is not compatible with UXM firmware Model A.

    2. If attempting to burn UXM firmware Model B into UXM firmware Model A with 9.2 software, the firmware Model B will not be burned into the UXM card due to the incompatibility of software 9.2 and UXM firmware Model A. The UXM has to be returned to Cisco for service.

    3. If using MEA/MEB/MEC BXM firmware and upgrading to MED or later, the 9.2.30 or later software has to be upgraded first so that the BXM will report 2-port groups for 2-port cards all the time. The smooth transition between the earlier 1 port group and the newly reported 2-port groups also displays message in dspcd "Inconsistency with logical PG #" (port group number). All earlier software will mismatch the card. This applied to BXM-OC3 or BXM-OC12 and configured to channel statistic level 2 or higher.

    4. Firmware MED and earlier supports APS Redundancy on Legacy BXM only.

    5. Because of hardware limitations, BXM hardware is not able to recognize all user-programmed cell transmission rates. Rather only discrete transmission rates can be used instead.

The equation below shows what the BXM hardware actually transmits given a user configured cell rate. The transmitted cell rate is always less than or equal to the configured cell rate. To prevent any cell loss, the transmitted cell rate must be equal to the configured rate. To do so, a cell rate must be chosen from the table below.
The rate table below lists the highest 200 cell rates supported be BXM such that if used, will result in no cell loss (given cell traffic is less than configured cell rate). Additional rates can be calculated using 1470588/[n + (1/256)], where n is an integer.
The logic to calculate the actual cell transmission rate in a BXM card is as follows:
    if (configured cell rate == full line cell rate) then
    	transmitted cell rate = full line cell rate
 
else
    	transmitted cell rate = from equation below or from table below




Example:
If a trunk is configured at 100,000 cells per second (cps), the actual transmitted cell rate is then 98,013 cps, any traffic sent over 98,013 cps would be discarded.
If a trunk is configured at 98,013 cps, then the actual transmitted cell rate is 98,013 cps with no cell loss.
Therefore, only rates in the table should be used. Otherwise, cell loss may be experienced. The table will not be exhausted at the end but still go on with the computing from the above equation.

1464865

56552

28832

19348

14559

11670

9738

8355

733860

54458

28278

19097

14416

11579

9674

8308

489558

52513

27744

18852

14277

11488

9611

8261

367288

50703

27231

18614

14139

11399

9549

8215

293888

49013

26736

18381

14005

11311

9487

8169

244938

47432

26258

18154

13872

11225

9426

8124

209966

45950

25798

17933

13743

11140

9366

8079

183733

44558

25353

17717

13616

11056

9307

8035

163327

43247

24923

17506

13491

10974

9248

7992

147001

42012

24508

17300

13368

10892

9190

7948

133642

40845

24106

17099

13248

10812

9133

7906

122509

39741

23717

16902

13129

10733

9077

7863

113088

38695

23341

16710

13013

10656

9021

7822

105012

37703

22976

16522

12899

10579

8966

7780

98013

36761

22623

16339

12787

10503

8912

7739

91889

35864

22280

16159

12677

10429

8858

7699

86485

35010

21947

15983

12568

10355

8805

7659

81681

34196

21625

15812

12462

10283

8753

7619

77383

33419

21311

15643

12357

10212

8701

7580

73515

32676

21007

15479

12254

10141

8650

7541

70014

31966

20711

15318

12153

10072

8599

7502

66833

31286

20423

15160

12053

10003

8549

7464

63927

30634

20143

15005

11955

9936

8500

7427

61264

30009

19871

14853

11859

9869

8451

7389

58814

29409

19606

14705

11764

9803

8403

7352

.....

    6. On the BPX with MGX 8220 feeder(s), regardless of the setting of the Node Parameter "42 Enable Feeder Alert," a feeder alert message will be sent to all MGX 8220 feeders immediately before a hitless rebuild takes place. The feeder alert message will temporarily disable the LMI polling from the MGX 8220 feeders. The MGX 8220 polling will resume as soon as the BPX is ready to exchange LMI messages.

    7. The amount of traffic allowed on a VP tunneling connection is two-thirds bandwidth of that connection. The minimum bandwidth must be 100 cells per second. For example, a CBR connection with a peak cell rate 1500 cps then can pass traffic up to 1000 cps.

    8. For IMA trunks, the configuration is blocked if the converted cps of the number of links to be decremented is MORE than the transmit rate (CSCdm71616).

Limitations

    1. For Switch Software 9.2, MPLS and PNNI controllers cannot coexist.

    2. In Release 9.2.30 and later, nodes might declare a communication break when using the BXM virtual trunking feature. The problem has been observed under the following conditions:

    The simplest example follows below:
    node_A ------ vtrk ----- node_B -----vtrk -----node_C
    On the above diagram, node_B is a virtual trunk share a common port
With this topology, "node_A" sees "node_C" as unreachable and vice-versa; however, "node_A" communicates to "node_B," and "node_B" communicates to "node_C."
Workarounds:

    3. When the cnfrsrc command is used to delete VSI partitions on an interface, software does not check if any Soft Permanent Virtual Circuit (SPVC) connections exists on that partition. Even if there are SPVC connections on a partition, the partition can be deleted using the cnfrsrc command. The only protection is that users are provided with a warning when they try to delete the partition.

If there are SPVC connections on a partition and if the partition is deleted, the SPVC connections will be left in a undefined and unrecoverable state. Hence, before deleting a VSI partition, ensure that all the SPVC connections are deleted on that partition.

    4. Switch Software 9.2.30 or later and BXM firmware MFC and later support the attachment of multiple MPLS controllers.

Switch Software 9.2.30 or later and BXM firmware MFB and later support the attachment of a PNNI controller.

    5. For UVM cards, there will be no new revisions of Model A firmware. When attempting to download Model A firmware to a UVM, software will give the user an error message indicating that the firmware does not match the card type. Note that there is no problem with continuing to use existing UVM cards running the old firmware(CSCdp08741).

    6. For a virtual trunk on a BXM/UXM, the Transmit Trunk Rate (the transmit rate of the virtual trunk) is configurable to match the PCR value of the subscribed public VPC service. In this release, the actual shaping rate for a virtual trunk is higher than the configured Transmit Trunk Rate (CSCdm80482). The actual virtual trunk shaping rates are 1/(n x 680 x 10-9) cells per second, where n is an integer from 1 to 29,411. In this release, the user-configured Transmit Trunk Rate is rounded to the next higher (as opposed to lower) actual shaping rate for shaping.

To configure a virtual trunk so that the actual shaping rate is not greater than the PCR value of the subscribed public VPC service, the following steps can be taken:
Step 1   Determine the n such that 1/(n x 680 x 10-9) cps (the actual shaping rate) is no greater than the PCR value of the subscribed public PVC service. For example, if the PCR value of the subscribed public PVC service is 10 Mbps or 23,585 cps, the n will be 63 and the actual shaping rate is 23,342.67 cps.

Step 2   Configure the Transmit Trunk Rate for the virtual trunk to be less than 1/(n x 680 x 10-9) cps but greater than 1/((n+1) x 680 x 10-9) cps. For example, if the PCR value of the subscribed public VPC service is 10 Mbps or 23,585 cps, configure the Transmit Trunk Rate for the virtual trunk to be less than 1/(63 x 680 x 10-9) = 23,342.67 cps but greater than 1/(64 x 680 x 10-9) = 22,977.94 cps.

    7. There is a new traffic class added in Release 9.2.20 that causes a trunk parameter conflict with pre-9.2.20 node. The conflict fails adding trunk between 9.2.20 BTM/ATM and pre- 9.2.20 BTM/ATM.

All ATM traffic classes are set for BTM/ALM trunks and is hidden to the user. The introduction of rt-VBR traffic class in 9.2.20 makes it different from pre-9.2.20 BTM/ALM trunk traffic class. The user can not change the ATM traffic class for BTM/ALM trunk.
This problem exists with a new BTM/ALM trunk on an upgraded 9.2.20 node but does not exist with an upgraded BTM/ALM trunk since the rt-VBR traffic class is not set while upgrading (CSCdm64345).

    8. The cloud port to which a virtual trunk is connected should have ILMI polling disabled. Otherwise, it could lead to a virtual trunk being clear on one end and declaring Virtual Trunk Path Failure at the other end (CSCdm52909).

    9. In a BPX that contains BCC cards with 64MB, there is no limitation. All 12 available slots can contain BXM or Enhanced-BXM cards.

In a BPX that contains BCC cards with 32MB, a maximum of 10 legacy BXM cards are allowed. If some Enhanced-BXM cards are used in place of BXM, then each Enhanced-BXM will count as two BXM cards.

    10. For performance reasons, AIS status of connections is not sent to the standby BCC. After switchcc, it may take a few minutes to update the AIS status of connections. If dspcon does not show the proper status of AIS or the dspalms screen shows an incorrect number of AIS, (after switchcc) wait for few minutes so that the status gets updated. (The dspalms and dspcon commands show the status of AIS.)

    11. Hitless rebuild has similar limitations to that of a switchcc and full rebuild:

Some will be re-enabled automatically. These include:
All other statistics have to be re-enabled for collection after a hitless rebuild takes place. These mainly include the user statistics.

    12. UVM cards in Y-redundancy will mismatch if one is burned with Idle Code Suppression Firmware and the other is not.

When installing/burning Idle Code Suppression Firmware on UVM pairs, the Y-redundancy must be removed, firmware in both UVM cards burned, and then the Y-redundancy can be restored.

    13. Mismatch is reported when replacing a BXM card with another BXM card that has a different port group, even though both BXM cards have the identical channel number.

    14. When upgrading from Release 9.1 to 9.2, the 9.1 statistics on BXM/UXM cards are supported to maintain compatibility. However, once a user configures a statistics level in 9.2, the statistics cannot be configured back to 9.1 statistics.

There is no 9.1 statistics support for BXM/UXM cards that were shipped with 9.2 firmware since the BXM/UXM card has the default level 1 statistics.
Therefore, when using a UXM with 9.2, a user must either:
OR

    15. The BXM and UXM channel statistics level feature gives these cards the capability of collecting more than four statistics per connection. However, it is the controller card's limitations, available memory, and performance, that indicates how many statistics can actually be collected from the cards and then reported to the Cisco Wan Manager (CWM).

The BCC-3-64 can collect at most three interval statistics per connection when there are 16,000 AutoRoute (AR) connections configured on the node. (Interval statistics are those statistics that are reported to the CWM. They are often referred to as TFTP statistics.)
You can collect approximately 48,000 statistics (3 x 16,000) on the BCC-3-64. This is approximate because there are many variables that will affect this value, such as are peaks enabled, how many buckets are collected, are all connection of the same type, are trunk, line or port statistics enabled, and so on.
With this approximation of 48,000 statistics on the BCC-3-64, this then means that as a rough estimate you could enable 32 statistics on 1,500 connections, 48 statistics on 1,000 connections or nine statistics on 5,000 connections, and so on. The approximation formula being:
max_stats_per_connection = 48,000/number_of_connections

    16. In Release 9.1, the UXM card ran a proprietary IMA communication protocol. This protocol matched that used on the MGX 8220 4 IMATM-B cards and hence could be connected together to form a trunk. In Release 9.2, we now support standards-compliant IMA on the UXM card. The standards-compliant IMATM-B on MGX 8220 5.0 is not yet released. Hence, when the network is upgraded to 9.2., the UXM will be running compliant IMA protocol and the IMATM-B will still be running the proprietary IMA communication protocol. They will no longer communicate and the trunk will fail. This will be fixed in the MGX 8220 5.0 release containing IMATM-B. However, it should be noted that an upgrade at that time will also incur some amount of downtime as there will be a difference in timing between the MGX 8220 upgrade and the switch software upgrade. There should be no effect to UXM-IMA trunks connected to other UXM-IMA trunks in 9.1 to 9.2 interoperability mode.

    17. The transmit rate on an IGX IMA trunk can be altered at the local node with any trunk outage. It is possible that the transmit rates are different at the two ends of an IMA trunk. After this trunk is deleted, it cannot be added back unless the transmit rates are the same.

    18. When doing a grouped upgrade from Release 9.1 to 9.2, the software error 1427 may be logged on the BPX/IGX node during a non-graceful upgrade. This error can be ignored since it is harmless to the network (CSCdm14613).

    19. Reconfiguring trunk parameters might cause connections to be rerouted if the changed bandwidth load is smaller than what was used by the connections that use the trunk.

    20. If LMI/ILMI is provided by the BCC:

The maximum possible number of ports on the BPX 8600 that can be configured with LMI/ILMI enabled is 52. However, each BPX will support up to a total of 16 feeder trunks and each feeder trunk will have LMI enabled. That is, if a BPX 8600 is configured with only two feeder trunks, then only (52 - 2) = 50 ports can have LMI/ILMI enabled.
If LMI/ILMI is provided by the BXM firmware:

    21. Virtual Path Connections with cells whose VCI values are above 4095 will be transmitted correctly only if the path is exclusively through BXM trunks and terminate at BXM ports.

    22. The feature of CIR=0 for Frame Relay connections is not supported for connections terminating between FRM cards in IGX nodes and FRSM cards in an MGX 8220 shelf.

    23. SVC connections are derouted after decreasing the allocated bandwidth (increasing Statistic Reserve). It is the design intent that increasing the statistical reserve will cause SVC conns to derouted and not be rerouted (CSCst92308).

    24. For the loadrev operation, it is important that the Cisco Wan Manager/TFTP buffers are maintained at their default size.

    25. Due to a hardware limitation, the BNI trunk will send 13-15 percent more traffic than what it is configured for when the trunk is configured for less speed (cps) than the maximum port speed. This is especially important when the BNI trunk is connected to IMATM pairs, which carry less than T3 bandwidth.

    26. When using the shift/no-shift feature on a BPX 8600 node's port card, controlled via the cnfport command, the other end of the connection must have the same setting. Otherwise, there will be a loss of continuity.

    27. When deleting trunks, there is a known limitation with the switch software. The deltrk command should always be executed on the node that remains as part of the network, rather than from the node that ends up being removed from the network. This is to ensure that all the necessary updates are sent to the rest of the network (CSCdi85134). Also if the command is not used as recommended here, a software error 419 could occur (CSCdi91285).

    28. Due to trunk-based loading, any commands having to do with trunk loading and the load model (dspload chklm dsplm, and so on.) need to be done only after waiting a certain period of time. This time is a direct function of the trunk load update interval time (as configurable) plus the conditional update latency time.

    29. The external ABR segment control loop on ForeSight (ABRFST) is an option at the user interface. It is supported by UXM-E/BXM-E but is not supported by UXM/BXM hardware. The user should not enable this option on ForeSight connections (CSCdi92451). In any case, there is no coupling between the loops.

    30. On a heavily loaded BPX 8600 node, during connection rerouting, the status of a particular connection is indicated as OK even though the line status of the other end of the connection is listed as failed. The connection is in fact OK, because the conditioning of the connection (to update the status for both ends) is done by a low-priority process so that the rerouting of the connections can be given high priority. The status will be eventually updated. (CSCdj10762)

    31. A node whose number is greater than 63 cannot have a clrcnf operation performed on it. This is as designed. A clrallcnf can be done, or the node must be renumbered to less than 63 before running clrcnf (CSCdj14920).

    32. The interface between a BXM feeder trunk and an MGX 8220 feeder is always considered to be an NNI interface. (CSCdj16808)

    33. When adding more than 4000 connections on a BPX node, the VC polling rate must be changed to a higher interval, to accommodate the additional time needed to poll for the statistics for each VC. The cnfsysparm command, parameter 24, must be changed according to the following:

 0-3999 connections

Polling Rate: 5 Minutes (or higher)

 
 4000-7999 connections

Polling Rate: 10 Minutes (or higher)

 
 > 8000 connections

Polling Rate: 15 Minutes

    34. Given a connection that terminates on an IGX 8400 FRM at one end and an ASI on the other end, tstdelay initiated at the FRM end may not work if the ASI firmware is below the appropriate revision and does not support OAM cells as opposed to supervisory cells. This is because the updated BTM on the IGX will always generate OAM cells. Please check the Compatibility Matrix.

    35. Because the detailed card error event log is not retained within BRAM, this information will be lost should a processor rebuild occur. Therefore, when issuing a dspcderrs command on a particular slot, the display will not show the detailed card error information should a rebuild event occur. This functionality has not been modified from previous releases.

    36. When a physical-layer failure (for example, LOS) is detected on the BXM, a Major Alarm is generated, and any connection routed over that port is downed (fail state). The software sends a command to the remote end of the connection to generate AIS in the egress direction (CSCdj30543).

Impact:
Since the connection is in a failed state, AIS is generated in the upstream direction (in addition to the downstream direction). Although this does conform to the letter of the I.610 standard, this is not necessarily what a user would expect to see, because it interferes with the RDI response from the end-to-end connection termination point. (A fault in the downstream direction causes a fault in the upstream direction.)
Reason for the current implementation:
The BNI can not generate AIS. If there is a fault at a BNI trunk, the current mechanism is to cause AIS to be generated by the BXM port by downing the connection. Since the BXM can generate only OAM cells from the RCMP, and the RCMP is in the ingress path, the cells must be backward routed to the egress (egress QE). Also, since end-to-end OAM cells are required, the ingress QE must be configured to drop ALL cells in the ingress path. This creates a break in continuity in the opposite direction, and AIS cells must also be generated at the other end of the same connection, in the upstream direction of the original fault.

    37. There are problems in the downgrade mechanism that can cause database corruption. If a downgrade is performed immediately after upgrading, the Stby_Info revision fields are not yet filled in on the new active CC. They don't get filled in until there is an upcard response from the new locked CC. This causes a restart instead of a switchcc. If the locked CC is reset, then downgrade immediately, a restart will occur instead of a switchcc. (CSCdj30811).

    38. In order to test/simulate the Y-redundant switchover of ASI T3 or E3 pairs the resetcd command must be used, or by pulling out the active card. It will not be correctly simulated by doing a dncd (down card) on the active card. Using dncd will cause cell discards (CSCdj08923).

    39. UBR traffic gains an advantage over ABR traffic when UBR and ABR PVCs are combined on the same network. This is because UBR and ABR PVCs share the same Qbin (Class of Service Queue) on the BXM card. ABR PVCs use a flow control mechanism, VSVD, which ensures that traffic sources slow down when the Qbin usage exceeds the EFCI threshold. However, UBR PVCs do not have this throttling mechanism. Therefore, ABR will throttle back whereas UBR will not. This unfair advantage is not considered a problem, since the decision to share a Qbin for ABR and UBR traffic was intentional. Any best-effort service that one would route over UBR can be routed over ABR(VSVD), with the additional benefit of protecting resources in the network. If UBR and ABR PVCs are required then:

Option 1: Consider adding all best-effort PVCs as UBR
Option 2: Isolate the ABR and UBR paths by using cnfpref command to ensure that ABR and UBR PVCs do not share the same queues.
Option 3: To provide UBR service on a connection, rather than setting up a UBR connection, do the following:
Step 1   Set up an ABRSTD connection.

Step 2   Enable VSVD.

Step 3   Disable FCES (Flow Control External Segment).

Step 4   Disable DEFAULT EXTENDED PARAMETERS.

Step 5   Choose policing option "4" to allow access as UBR.1 (PCR policing only). This connection has ABR VSVD in the network and allows UBR.1 access. The MCR for such ABRSTD connection may be set at the minimum acceptable value of 6 cells per second (explained later to do so).

To provide ABR service on a connection, set up an ABRSTD connection, enable VSVD and enable FCES to allow RM cells to be passed to and from customer equipment. The MCR for such ABRSTD connections can be set at any user-desired value.
When the network is experiencing congestion, all the affected ABRSTD connections, regardless of the services (ABR or UBR) they are carrying, will all be throttled back at the VSVD points at the network edge. During network congestion, connections carrying UBR services are virtually stopped (to a throughput of a mere 6 cps) while connections carrying ABR services can send at a much higher, user-desired MCR. This option would avoid that UBR service gains an unfair advantage over ABR service while sharing the same CoS queue.

    40. Combining Frame Based Traffic Control (FBTC) and non-FBTC connections within a Class of Service can cause FBTC connections to not receive a fair share of bandwidth. For example, if VBR connections are added at a terminating port, and some of these VBR connections have FBTC enabled while other VBR connections have FBTC disabled, the VBR connections with FBTC disabled may obtain all of the excess bandwidth before the connections with FBTC enabled receive any of the excess bandwidth. The same holds true for ABR or UBR connections. This is relevant only where FBTC and non-FBTC connections share a Qbin, either at a port or at a trunk.

    41. The maximum number of VC PARMs supported: 749 for BCC-32 MB, 2,999 for BCC-64 MB. (CSCdj48589).

VC PARMs are Virtual Circuit Parameters combinations/sets. One set of VC Parameter is used for each unique Virtual Circuit that has been provisioned. Identically provisioned VCs (exclusive of end points) use the same set of parameters. Thus, on a 32MB BCC, a total of 749 uniquely configured Virtual Circuits can be provisioned.

    42. Care must be taken when changing the Deroute Delay parameter, which is controlled by the cnftrk command. This defaults to zero, but if set to anything but zero, connection rerouting, due to a trunk failure, will be delayed as provided by the parameter.

Required Workarounds

    1. When adding a node into an existing network, ensure that its node number is unique prior to a actually adding it into the network. Use the rnmnd command, and renumber the individual node while it is still stand-alone. This will make the joining of this node much simpler, and will avoid the problem of a node renumbering an active network, as described below.

    2. There is a problem with node renumbering. Node renumbering (the rnmnd command) should be executed only during a stable network environment and only if absolutely necessary. A stable network environment would be, for example, one in which no connection was added for the past 30 minutes and no topology change was made in the last hour and there are no alarms or node unreachabilities. Node renumbering must be done only when the network is stable to reduce the possibility of certain temporarily blocked messages during the node renumbering process from being delivered to the wrong nodes. This would occur after the completion of the node renumbering process. It is recommended that a node be renumbered prior to being added to the network.

    3. The settling time for network-wide updates can take a long time in certain situations. Specifically, the settling time for updates due to network-wide topology changes and connections in a large network when a processor switchover occurs can take a long time. The time is proportional to the number of nodes as well as the number of connections. A general estimate would be 30 seconds per node. During the period of transitions (when the updates are occurring) some network operations such as adding connections might in some cases take somewhat longer to complete.

    4. When using Cisco Wan Manager, there could be a problem with communicating with a node that just had a processor switchover. The problem is within the SPARCstation itself and its caching of EtherNet addresses. It can be solved by execution the following command on the workstation as the superuser: # arp -d <node_name>

    5. Users may not use the command addcon slot.1-24 v to add 24 voice connections to a CVM/UVM at once. Instead, they must separate this activity into two or more commands, so that no more than 16 connections are added at once. This is an issue only for voice connections. Data connections can be added using the "1-24" syntax. This also applies when the CVM/UVM circuit line is an E1, in which case "1-32" would apply (CSCdj14319).

    6. Statistics must be disabled prior to the start of an upgrade, prior to the issuing of the first loadrev command. Statistics should be disabled from the Cisco Wan Manager, which is the Statistics collection manager.

    7. Statistics sampling must be disabled prior to the start of an upgrade (using off1/off2), prior to the issuing of the first loadrev command. Statistics sampling state machines should be disabled from the Command Line Interface.

    8. When a switchcc is executed on a BPX 8600 configured with two BCC-4 cards and contains a BXM-622 trunk card, there may be a bad clock path problem reported. It is indicated as a Minor Alarm - bad clock path. This is a transitory problem, although the alarm indication persists. To clear this, execute the clrclkalm command.

    9. Currently, T3-3 and T3-2 back cards are not interchangeable between ASI and BNI front cards, as this has been the case since the introduction of these cards. The back cards must be configured using cnfbkcd (with setnovram) so as to avoid back card mismatch (CSCdj41999).

Additional Documentation

The command dspbpnv can be issued to verify if the node has the new backplane or the old backplane. The following chart details the bit fields for the BCC Backplane NOVRAM format, the values in bytes numbered 4 and 5 describe the back plane type.
The command cnfbpnv can be used to configure the backplane, if backplane is so enabled.

16-Bit Word

Byte # (hex)

Contents

 0


 0,1


 Hardware revision


 1


 2,3


 Backplane Type (usually 0x65=101 decimal)


 2


 4,5


 Backplane version (0x0000:old   0x0001:new)


 3


 6,7


 Backplane serial number in ASCII - MSB 


 4


 8,9


                             "


 5


 A,B


                             "            LSB


 6


 C,D


 Board FAB number, in ASCII - MSB


 7


 E,F


                            "


 8


 10,11


                            "


 9


 12,13


                            "


 A


 14,15


                            "


 B


 16,17


                            "     LSB


 C


 18,19


 Unused


 D


 1A,1B


 Unused


 E


 1C,1D


 Unused


 F


 1E,1F


 Checksum bytes - CURRENTLY NOT SUPPORTED

Compatibility Notes

For a complete list of firmware revisions supported, see the Compatibility Matrix document, which is included in this release package.

This release will run with Release 4.0.0x, 4.1.0x, or 5.0.0x of the MGX 8220.

Compatibility Matrix

BPX 8600 Firmware Compatibility

PCB Description

dspcds Name

Card Name in FW Image 

Model

Latest F/W

Min F/W

 BCC boot


 BCC


 BCC


 B


 HBJ


 HBJ


 BCC3-32 boot


 BCC-3


 BCC


 C


 HCM


 HCM


 BCC3-64 boot


 BCC-3


 BCC


 D


 HDM


 HDM


 BCC4 boot


 BCC-4


 BCC


 E


 HEM


 HEM


 BCC4-128 boot


 BCC-4


 BCC


 H


 HHM


 HHM


 ASI 2T3/2E3


 ASI-T3


 ASI


 C


 UCF


 UCF


 ASI 2T3/2E3


 ASI-E3


 ASI


 C


 UCF


 UCF


 ASI-155-E


 ASI155E


 ASI-155


 E


 WEC


 WEC


 ASI-155


 ASI-155


 ASI-155


 H


 WHC


 WHC


 ASM


 ASM


 


 A


 GAC


 GAC


 BNI-3T3/3E3


 BNI-T3


 BNI


 C


 TCM


 TCM


 BNI-3T3/3E3


 BNI-E3


 BNI


 C


 TCM


 TCM


 BNI-155


 BNI-155


 BNI-155


 B


 VBR


 VBR


 BNI-155-E


 BNI155E


 BNI-155


 D


 VDR


 VDR


 BXM-BME


 BME


 BME


 K


 MKA


 MKA


 BXM-T3-8/12


 BXM-T3


 BXM


 E


 MEJ


 MEB


 BXM-T3-8/12


 BXM-T3


 BXM


 F


 MFD


 MFA


 BXM-E3-8/12


 BXM-E3


 BXM


 E


 MEJ


 MEB


 BXM-E3-8/12


 BXM-E3


 BXM


 F


 MFD


 MFA


 BXM-155-4/8


 BXM-155


 BXM


 E


 MEJ


 MEB


 BXM-155-4/8


 BXM-155


 BXM


 F


 MFD


 MFA


 BXM-622/622-2


 BXM-622


 BXM


 E


 MEJ


 MEB


 BXM-622/622-2


 BXM-622


 BXM


 F


 MFD


 MFA


 BXM-T3-8E/12E/12EX


 BXM-T3


 BXM


 E


 MEJ


 MED


 BXM-T3-8E/12E/12EX


 BXM-T3


 BXM


 F


 MFD


 MFA


 BXM-E3-8E/12E/12EX


 BXM-E3


 BXM


 E


 MEJ


 MED


 BXM-E3-8E/12E/12EX


 BXM-E3


 BXM


 F


 MFC


 MFA


 BXM-155-4D/8D/4DX/8DX


 BXM-155


 BXM


 E


 MEJ


 MED


 BXM-155-4D/8D/4DX/8DX


 BXM-155


 BXM


 F


 MFD


 MFA


 BXM-622-2D/DX/2DX


 BXM-622


 BXM


 E


 MEJ


 MED


 BXM-622-2D/DX/2DX


 BXM-622


 BXM


 F


 MFD


 MFA

IGX 8400 Firmware Compatibility

PCB Description

dspcds Name

Card Name in Firmware Image 

Model

Latest F/W

Min F/W

 NPM boot


 NPM


 NPM


 A


 RAS


 RAR


 NPM 32 boot


 NPM


 NPM


 B


 RBS


 RBR


 NPM 64 boot


 NPM


 NPM|NPM-64


 C


 RCS


 RCR


 NPM-B 32 boot


 NPM


 NPM|NPM-32B


 E


 RES


 RER


 NPM-B 64 boot


 NPM


 NPM|NPM-64B


 F


 RFS


 RFR


 IGX-ALM/A


 ALM


 ALM-A


 A


 CAE


 CAE


 IGX-ALM/B


 ALM


 ALM-B


 B


 CBK


 CBH


 IGX-BTM/B


 BTM


 BTM


 A


 IAF


 IAF


 IGX-BTM/B


 BTM


 BTM


 B


 IBL


 IBL


 IGX-BTM/B


 BTM


 BTM


 D


 IDC


 IDC


 IGX-CVM-DS0A


 CVM


 CVM


 A


 DAF


 DAF


 IGX-CVM


 CVM


 CVM


 B


 DBF


 DBF


 IGX-CVM-TT


 CVM


 CVM


 C


 DCA


 DCA


 IGX-FRM


 FRM


 FRM


 D


 FDZ


 FDZ


 IGX-FRM-31


 FRM


 FRM-31


 E


 FEZ


 FEZ


 IGX-FRM-2


 FRM


 FRM-2


 F


 FFD


 FFD


 FRM (B)


 FRM


 FRM


 H


 FHB


 FHB


 IGX-FRM


 FRM


 FRM


 J


 FJB


 FJA


 IGX-FRM-31


 FRM


 FRM-31


 K


 FKB


 FKA


 IGX-FTM


 FTM


 FTM


 B


 JBJ


 JBJ


 IGX-FTM


 FTM


 FTM


 C


 JCB


 JCB


 IGX-HDM


 HDM


 HDM


 C


 SCF


 SCF


 IGX-LDM


 LDM


 LDM


 C


 LCC


 LCB


 IGX-NTM


 NTM


 NTM


 E


 NEK


 NEK


 IGX-NTM (B)


 NTM


 NTM


 F


 NFK


 NFH


 IGX-UFM-4C/8C


 UFM


 UFM-C


 A


 ZAS


 ZAN


 IGX-UFM-4C/8C


 UFM


 UFM-C


 B


 ZBC


 ZBA


 IGX-UFM-8C


 UFM


 UFM-C


 C


 ZCA


 ZCA


 IGX-UFM-U


 UFMU


 UFM-U


 A


 YAK


 YAH


 IGX-UFM-U


 UFMU


 UFM-U


 B


 YBB


 YBA


 IGX-UFM-U


 UFMU


 UFM-U


 C


 YCA


 YCA


 IGX-UVM


 UVM


 UVM


 B


 DBD


 DBD


 IGX-UVM


 UVM


 UVM


 C


 DCA


 DCA


 IGX-UVM


 UVM


 UVM


 D


 DDF


 DDF


 IGX-UVM


 UVM


 UVM


 E


 DEF


 DEA


 IGX-UXM


 UXM


 UXM


 B


 ABJ


 ABB


 IGX-UXME


 UXM


 UXM


 B


 ABJ


 ABB

Note   IGX-UVM model E is a superset of models A, B, and C firmware. A, B, and C are obsoleted and should not be used.

MGX 8220 5.0 Firmware Compatibility

PCB Description

CW2000 Name

Latest F/W

Min F/W

 ASC F/W


 ASC


 5.0.14


 5.0.10


 ASC Boot


 ASC


 1.0.03


 1.0.01


 ASC/2 FW


 ASC


 5.0.14


 5.0.10


 ASC/2 Boot


 ASC


 1.0.03


 1.0.01


 BNM-T3


 BNM-T3


 n/a


 n/a


 BNM-E3


 BNM-E3


 n/a


 n/a


 BNM-155


 BNM-155


 n/a


 n/a


 FRSM-4T1


 FRSM-4T1


 4.0.20


 4.0.19


 FRSM-4E1


 FRSM-4E1


 4.0.20


 4.0.19


 FRSM-4T1-C


 FRSM-4T1-C


 4.0.20


 4.0.19


 FRSM-4E1-C


 FRSM-4E1-C


 4.0.20


 4.0.19


 FRSM Boot


 FRSM-4T1


 4.0.00


 4.0.00


 FRSM Boot


 FRSM-4E1


 4.0.00


 4.0.00


 FRSM Boot


 FRSM-4T1-C


 4.0.00


 4.0.00


 FRSM Boot


 FRSM-4E1-C


 4.0.00


 4.0.00


 SRM T1E1 (B)


 SRM-T1E1


 n/a


 n/a


 SRM 3T3


 SRM-3T3


 n/a


 n/a


 CESM-4T1


 CESM-4T1


 4.0.16


 4.0.15


 CESM-4E1


 CESM-4E1


 4.0.16


 4.0.15


 CESM Boot


 CESM-4T1


 4.0.01


 4.0.01


 CESM Boot


 CESM-4E1


 4.0.01


 4.0.01


 CESM-8T1


 CESM-8T1


 5.0.14


 4.1.05


 CESM-8E1


 CESM-8E1


 5.0.14


 4.1.05


 CESM-8 Boot


 CESM-8T1


 1.0.01


 1.0.01


 CESM-8 Boot


 CESM-8E1


 1.0.01


 1.0.01


 AUSM-4T1


 AUSM-4T1


 4.0.20


 4.0.19


 AUSM-4E1


 AUSM-4E1


 4.0.20


 4.0.19


 AUSM Boot


 AUSM-4T1


 4.0.00


 4.0.00


 AUSM Boot


 AUSM-4E1


 4.0.00


 4.0.00


 FRSM-8T1


 FRSM-8T1


 5.0.14


 5.0.10


 FRSM-8E1


 FRSM-8E1


 5.0.14


 5.0.10


 FRSM-8T1 Boot


 FRSM-8T1


 1.0.02


 1.0.01


 FRSM-8E1 Boot


 FRSM-8E1


 1.0.02


 1.0.01


 AUSM-8T1


 AUSM-8T1


 5.0.14


 5.0.10


 AUSM-8E1


 AUSM-8E1


 5.0.14


 5.0.10


 AUSMB-8T1


 AUSMB-8T1


 5.0.14


 5.0.10


 AUSMB-8E1


 AUSMB-8E1


 5.0.14


 5.0.10


 AUSM-8T1E1 Boot


 AUSM-8T1


 1.0.02


 1.0.01


 AUSM-8T1E1 Boot


 AUSM-8E1


 1.0.02


 1.0.01


 AUSM-8T1E1 Boot


 AUSMB-8T1


 1.0.02


 1.0.01


 AUSM-8T1E1 Boot


 AUSMB-8E1


 1.0.02


 1.0.01


 FRSM-HS1


 FRSM-HS1


 5.0.14


 4.0.16


 FRSM-HS1/B


 FRSM-HS1/B


 5.0.14


 4.0.16


 FRSM-HS1 Boot


 FRSM-HS1


 1.0.01


 1.0.01


 FRSM-HS1 Boot


 FRSM-HS1/B


 1.0.01


 1.0.01


 FRSM-HS2


 FRSM-HS2


 5.0.14


 5.0.10


 FRSM-HS2 Boot


 FRSM-HS2


 1.0.01


 1.0.01


 IMATM


 IMATM-T3T1


 n/s


 n/s


 IMATM


 IMATM-E3E1


 n/s


 n/s


 IMATM


 IMATMB-T1


 5.0.14


 5.0.10


 IMATM


 IMATMB-E1


 5.0.14


 5.0.10


 IMATM Boot


 IMATM-T3T1


 n/s


 n/s


 IMATM Boot


 IMATM-E3E1


 n/s


 n/s


 IMATM Boot


 IMATMB-T1


 1.0.02


 1.0.01


 IMATM Boot


 IMATMB-E1


 1.0.02


 1.0.01

MGX 8850 1.1 Firmware Compatibility

PCB Description

CW2000 Name

Latest F/W

Min F/W

 PXM1


 PXM-1


 1.1.24


 1.1.24


 PXM1-2-T3E3


 PXM1-2T3E3


 1.1.24


 1.1.24


 PXM1-4-155


 PXM1-4OC3


 1.1.24


 1.1.24


 PXM1-1-622


 PXM1-OC12


 1.1.24


 1.1.24


 MGX-SRM-3T3/B


 SRM-3T3


 n/a


 n/a


 AX-CESM-8E1


 CESM-8E1


 10.0.12


 10.0.10


 AX-CESM-8T1


 CESM-8T1


 10.0.12


 10.0.10


 MGX-AUSM-8E1/B


 AUSMB-8E1


 10.0.12


 10.0.10


 MGX-AUSM-8T1/B


 AUSMB-8T1


 10.0.12


 10.0.10


 MGX-CESM-T3


 CESM-T3


 10.0.12


 10.0.10


 MGX-CESM-E3


 CESM-E3


 10.0.12


 10.0.10


 AX-FRSM-8E1/E1-C


 FRSM-8E1


 10.0.12


 10.0.10


 AX-FRSM-8T1/T1-C


 FRSM-8T1


 10.0.12


 10.0.10


 MGX-FRSM-HS2


 FRSM-HS2


 10.0.12


 10.0.10


 MGX-FRSM-2CT3


 FRSM-2CT3


 10.0.12


 10.0.10


 MGX-FRSM-2T3E3


 FRSM-2T3


 10.0.12


 10.0.10


 MGX-FRSM-2T3E3


 FRSM-2E3


 10.0.12


 10.0.10


 MGX-FRSM-HS1/B


 FRSM-HS1/B


 10.0.12


 10.0.10


 MGX-VISM-8T1


 VISM-8T1


 1.5.04


 1.5.01


 MGX-VISM-8E1


 VISM-8E1


 1.5.04


 1.5.01


 MGX-RPM-128M/B


 RPM


 12.1(1)T


 12.0(7)T


 CWM


 


 9.2.09


 9.2.08

BPX 8600 Hardware Compatibility

Card Type

Part Numbers

Latest H/W

Min. H/W

Controller Cards

 


 


 


 BPX-BCC-32M (Non-Orderable)


 73-213840-00


 P


 A


 BPX-BCC-64M (Non-Orderable)


 800-04008-04


 A


 A


 BPX-BCC-BC (Non-Orderable)


 73-211380-00


 D


 A


 BPX-BCC-3-32M (Non-Orderable)


 800-04004-04


 R


 J


 BPX-BCC-3-64M


 73-3720-02


 R


 J


 BCC-3BC


 800-02916-01


 E


 A


 BPX-BCC4V


 800-03580-06


 E


 C


 BPX-BCC4V/B


 800-06483-02


 C


 A


Alarm Group

 


 


 


 BPX-ASM


 800-04009-01


 C


 A


 BPX-ASM-BC


 73-211910-00


 C


 A


 ASM-LM


 800-211910-10


 B


 A


BroadBand Switch Group

 


 


 


 BPX-BXM-T3-8


 800-02777-07 


 H


 A


 BPX-BXM-E3-8


 800-02779-07


 H


 A


 BPX-BXM-T3-12


 800-02776-07


 H


 A


 BPX-BXM-E3-12


 800-02778-07


 H


 A


 BPX-T3/E3-BC


 73-2759-02


 A


 A


 


 


 


 


 BPX-BXM-155-8


 800-02664-07


 H


 B (C for APS)


 BPX-MMF-155-8-BC


 800-03255-01


 B


 A


 BPX-SMF-155-8-BC


 800-03257-01


 B


 A


 BPX-SMFLR-155-8-BC


 800-02593-02


 B


 A


 BPX-BXM-155-4


 800-02666-07


 H


 B (C for APS)


 BPX-MMF-155-4-BC


 800-03256-01


 B


 A


 BPX-SMF-155-4-BC


 800-03258-01


 B


 A


 BPX-SMFLR-155-4-BC


 800-02594-02


 B


 A


 


 


 


 


 BPX-BXM-622


 800-02646-10


 L


 D (E for APS)


 BPX-BXM-622-2


 800-02638-10


 L


 D (E for APS)


 BPX-622-2-BC


 73-2884-01


 D


 A


 BPX-SMF-622-BC


 800-03249-01


 C


 A


 BPX-SMF-622-2-BC


 800-03251-01


 C


 A


 BPX-SMFLR-622-BC


 800-03250-01


 C


 A


 BPX-SMFLR-622-2-BC


 800-03252-01


 D


 A


 BPX-XLR-622


 800-02738-01


 C


 A


 BPX-XLR-622-2


 800-02739-01


 C


 A


 


 


 


 


 BPX-BME


 800-02855-04


 B


 A


 BPX-BME-OC12


 73-2469-07


 F


 A


 BPX-BXM-E-T3-8E


 800-03933-02


 A


 A


 BPX-BXM-E-E3-8E


 800-03928-02


 A


 A


 BPX-BXM-E-T3-12E


 800-03931-02


 A


 A


 BPX-BXM-E-E3-12E


 800-03929-02


 A


 A


 BPX-BXM-E-T3-12EX


 800-03934-02


 A


 A


 BPX-BXM-E-E3-12EX


 800-03930-02


 A


 A


 BPX-BXM-E-155-4D


 800-03094-02


 A


 A


 BPX-BXM-E-155-4DX


 800-03093-02


 A


 A


 BPX-BXM-E-155-8D


 800-03092-02


 A


 A


 BPX-BXM-E-155-8DX


 800-03091-02


 A


 A


 BPX-BXM-E-622-DX


 800-03151-02


 A


 A


 BPX-BXM-E-622-2D


 800-03150-02


 A


 A


 BPX-BXM-E-622-2DX


 800-03149-02


 A


 A


 


 


 


 


 RDNT-SMF-155-4R


 800-03677-01


 J


 A


 RDNT-SMF-155-8R


 800-03679-01


 K


 A


 RDNT-LR-155-8R


 800-03678-01


 J


 A


 RDNT-LR-622-2R


 800-03676-01


 F


 A


 RDNT-SMF-622R


 800-03675-01


 F


 A


 RDNT-SMF-622-2R


 800-03674-01


 J


 A


 BPX-T3/E3


 800-03058-02


 E


 A


 BPX-E3-BC


 73-213070-01


 E


 A


 BPX-MMF-2-BC


 73-214290-00


 D


 A


 BPX-SMF-2-BC


 73-216270-00


 D


 A


 BPX-SMFLR-2-BC


 73-216270-01


 D


 A


 


 


 


 


 BPX-STM1-EL-4


 800-03716-02


 A


 A


 


 


 


 


 BNI-3-T3/C


 800-02858-02


 A


 A


 BNI-3-E3/C


 800-02859-02


 A


 A


 SMF-LM-OC3


 800-216270-10


 C


 A


 SMF-LM-OC3-LR


 800-216270-11


 C


 A


 MMF-LM-OC3


 800-214290-10


 B


 A


 LM-3T3


 800-213070-10


 D


 A


 LM-3E3


 800-213070-11


 D


 A

IGX 8400 Hardware Compatibility

Card Type

Part Numbers

Latest H/W

Min. H/W

* Note Below

Controller Cards

 


 


 


 


 IGX-NPM-32


 73-2894-01


 W


 A


 


 IGX-NPM-64


 73-2895-01


 W


 A


 


 IGX-NPM-32B


 73-2554-04


 L


 A


 


 IGX-NPM-64B


 73-2363-02


 C


 A


 


 IGX-SCM


 73-3341-01


 Y


 A


 Revision X or later for nodes with UXM IMA trunks


Alarm Group

 


 


 


 


 IGX-ARM


 73-218230-00


 B


 A


 


 BC-512011


 73-212360-00


 D


 A


 


Trunk Group

 


 


 


 


 IGX-NTM


 73-2296-04


 E


 A


 


 BC-6271A-TI


 73-207380-00


 M


 A


 


 BC-6171A-E1


 73-207370-01


 P


 A


 


 BC-6083A-SR


 73-208540-00


 J


 A


 


 BC-550150-Y1


 73-210820-01


 D


 A


 


 IGX-BTM/B


 73-3005-02


 B


 A*


 "*Show AIT H/W Rev, BTM(B)=AIT+ACM1"


 ACM1 


 73-2921-03


 W


 A


 


 BC-571110A-T3


 73-2879-01


 L


 A


 


 BC-571210A-E3


 73-2679-01


 K


 A


 


 BC-571310A-E2


 73-215940-00


 D


 A


 AIT BC HSSI/E2


 BC-571410A-HSSI


 73-216370-00


 A


 A


 AIT GIM HSSI


 IGX-ALM/A


 73-2558-03


 J


 A


 


 IGX-ALM/B


 73-2558-03


 J


 A


 


 BC-UAI-1T3


 73-217040-00


 C


 A


 


 BC-UAI-1E3


 73-2986-01


 E


 A


 


 IGX-UXM


 73-2511-03


 D


 A


 


 BC-UAI-4-155-SMF


 73-2703-03


 D


 A


 


 BC-UAI-4-155-MMF


 73-2705-03


 D


 A


 


 BC-UAI-2-155-SMF


 73-2699-03


 C


 A


 


 BC-UAI-6-T3


 73-2952-02


 A


 A


 


 BC-UAI-3-T3


 73-2954-02


 A


 A


 


 BC-UAI-6-E3


 73-2953-02


 A


 A


 


 BC-UAI-3-E3


 73-2955-02


 A


 A


 


 BC-UAI-8-E1-BNC


 73-2932-02


 C


 A


 


 BC-UAI-4-E1-BNC


 73-3061-01


 C


 A


 


 BC-UAI-8-T1-DB15


 73-2941-02


 C


 A


 


 BC-UAI-8-E1-DB15


 73-2942-02


 C


 A


 


 BC-UAI-4-T1-DB15


 73-3059-01


 C


 A


 


 BC-UAI-4-E1-DB15


 73-3060-01


 C


 A


 


 BC-UAI-4-STM1E


 73-3364-02


 A


 A


 


Port Group

 


 


 


 


 IGX-FTM


 73-2519-01


 M*


 A*


 "*Show FTC H/W Rev, FTM=FTC+ACM1A"


 ACM1A


 73-2930-03


 W


 A


 


 BC-6351A-V35


 73-213240-00


 E


 A


 FPC-V.35


 BC-6352A-T1


 73-213420-00


 C


 A


 FPC-T1


 BC-6353A-E1


 73-213410-00


 B


 A


 FPC-E1


 BC-6354A-X21


 73-214120-00


 C


 A


 FPC-X21


 IGX-HDM


 73-2853-02


 H


 F


 "*Show SDP H/W Rev, HDM=SDP+ACM2"


 ACM2


 73-2922-03


 T


 A


 


 BC-5082A-V35


 73-2450-01


 K


 A


 


 BC-5083A-RS449


 73-204850-00


 V


 A


 


 BC-5084B-RS232


 73-2723-01


 W


 A


 


 IGX-LDM


 73-207250-00


 K


 A


 "*Show LDP H/W Rev, LDM=LDP+ACM1A"


 BC-5286A-RS232


 73-207180-01


 L


 A


 LDI-4RS232


 BC-5287A-RS232


 73-207180-00


 L


 A


 LDI-8RS232


 IGX-CVM-DSOA


 73-3002-02


 D


 A*


 "*Show CDP H/W Rev, CVM=CDP+ACM1A"


 IGX-CVM-T1EC


 73-3003-03


 E


 A*


 "*Show CDP H/W Rev, CVM=CDP+ACM1A"


 IGX-CVM-E1EC


 73-209660-00


 H*


 A*


 "*Show CDP H/W Rev, CVM=CDP+ACM1A"


 BC-6271A-TI


 73-207380-00


 M


 A


 


 BC-6171A-E1


 73-207370-01


 P


 A


 


 BC-550100-J1


 73-210820-00


 C


 A


 


 IGX-FRM


 73-2517-03


 N


 A


 


 IGX-FRM-31


 73-2517-03


 N


 A


 


 IGX-FRM-2


 73-2519-01


 M*


 A*


 "*Show FRP H/W Rev, FRM-2=FRP+ACM1A"


 BC-6251B-V35


 73-3253-01


 M


 A


 FRI-4V.35-2


 BC-6254A-X21


 73-211440-00


 H


 A


 FRI-X.21


 BC-6355A-X21


 73-214120-01


 C


 A


 FRI-2X21


 


 


 


 


 


 IGX-UFM-4C


 73-2531-05


 N


 A


 


 IGX-UFM-8C


 73-2531-05


 N


 A


 


 BC-UFI-8T1-DB15


 73-2444-02


 D


 A


 


 BC-UFI-8E1-DB15


 73-2445-02


 D


 A


 


 BC-UFI-8E1-BNC


 73-2449-02


 D


 A


 


 IGX-UFM-U


 73-2349-04


 D


 A


 


 BC-UFI-12V35


 73-2711-01


 D


 A


 


 BC-UFI-12X21


 73-2712-01


 D


 A


 


 BC-UFI-4HSSI


 73-2693-01


 C


 A


 


 


 


 


 


 


 IGX-UVM


 73-2361-04


 K


 A


 


 BC-UVI-2E1EC


 73-2420-01


 B


 A


 


 BC-UVI-2T1EC


 73-2373-01


 C


 A


 


 BC-UVI-2J1EC


 73-2374-01


 A


 A

Known Anomalies

The following is the list of known anomalies in this Switch Software delivery. Included with each is a brief discussion of the problem. A more in-depth discussion is available in the release note enclosure of the problem record in Bug Navigator.

Bug ID 

Description

 CSCdm60702


 Symptom:


 When a bus error occurs on a node, and a rebuild results, other nodes in the network will see the rebuilding node in the degraded state. This shows up as "UNDeg" in the dspnds screen. A log message will also appear on these other nodes indicating that the rebuilding node went unreachable due to degradation. The unreachability will recover automatically. 


 Conditions:


 Occurs only if a node rebuilds due to a bus error, and the degraded mode is enabled in cnfnodeparm. Will not occur if a node switches processors due to a bus error. 


 Workaround:


 No workaround needed. No adverse effects.


 CSCdm60707


 Symptom:


 Can take longer than expected to clear unreachability with a node that has rebuilt due to a bus error. Other nodes in the network will declare the node unreachable due to degradation ("UNDeg"). The unreachability will eventually clear automatically. 


 Conditions:


 Occurs only if a node rebuilds due to a bus error, and if degraded mode is enabled in cnfnodeparm on that node. 


 Workaround:


 None needed. Problem clears automatically. 


 CSCdm78849


 Symptom:


 Message stating "CMI message drop" would be seen occasionally on the UXM debug console. If this occurred 10 consecutive times on the same message, SWSW would declare a swerr 103 and subsequently reset the card. Though this happens frequently, the chances of it happening 10 consecutive times on the same message are extremely low. 


 Workaround: 


 None (not required).


 CSCdp51531


 Symptom:


 Software error code 21 is logged when a UBR connection is added on an ASI-155 card. 


 Conditions:


 Prior to Release 9.1.17, the error is logged when the UBR connection has CLP disabled, and the PCR is less than 10 cps. 


 In Release 9.1.17 and later, the error is logged under two conditions; when the UBR connection has CLP enabled, OR when CLP is disabled on a connection with PCR less than 10 cps. 


 Workaround:


 When adding the connection, do not enable the "CLP Setting." This will avoid the software error and ensure the connection is programmed correctly. 


 CSCdp57264


 On c7500, if multiple subinterfaces are configured on an ATM interface connected to BPX, each of subinterfaces with one PVC and BPX is configured to send ILMI traps, when the PVCs' state is changed on BPX, BPX will send out trap for all the PVCs but c7500 only brings down one subinterface (one pvc). 


 CSCdp98648


 Symptom:


 Equipment MGR cannot tell the difference between BXM legacy or enhanced. 


 Workaround:


 Log into the BPX node, execute dspcd XX to determine the number of channel supports. The enhanced version of the BXM card has 61K channels, and the BXM card has less than 61K channels. 


 CSCdr22814


 Symptom: 


 BPX returns an error indicating there are no channels available for networking when attempting to create a trunk or line. 


 Condition: 


 A precondition is that all channels on this card are currently being used by existing trunks or lines. When a trunk or line is deleted, which then theoretically would free up channels for another trunk/line, and a user attempts to subsequently recreate this trunk or another trunk intending to use the same channels that were just freed by the removal of the previously mentioned trunk/line, the user will find that no channels are available to create this new trunk. 


 Workaround: 


 Perform a hardware reset on the involved BXM card to free the channels that are no longer in use by the deleted trunk/line.


 CSCdr26043


 Symptom:


 BXM cards are going to Active-F state. 


 Condition: 


 Background test enabled. 


 Workaround:


 Replace the BXM card or the BCC card. 


 CSCdr26161


 Symptom:


 During a burnfwrev on a UXM card, a message "Already burning firmware. Try again later" appears for a long period of time (more than 10 minutes) if the UXM card is reset during the burnfw process (after the download is complete, i.e., after the Burn Addresses stop updating). 


 Conditions:


 Reset must be done after all burn addresses are updated. 


 Workaround:


 Do not reset the card during burnfw process.


 CSCdr29721


 Symptom:


 SW log 9000 and 103 occurs during downgrade from 9.2.31 to 9.2.3g 


 Conditions:


 This problem occurs during a loadrev 9.2.3g is tried when the primary was running 9.2.31, then ran runrev 0.0, and did a lanbtld. After a lanbtld swlog 9000 and 103 occured. 


 Workaround: 


 None 


 CSCdr30543


 Symptom:


 Cell loss and invalid frame format for a UXM-FRM connection 


 Conditions:


 The traffic was pumped from UXM port, using the standard frame relay parameters. 


 Workaround: 


 None 


 CSCdr30911


 Symptom:


 Software error 3041 is logged after a specific sequence of commands are executed on a BXM trunk card. 


 Conditions:


 This occurs if there is a connection routed through a BXM trunk and the following sequence of events occurs: 1) The card is downed (dncd) 2) The trunk is deleted from the network (deltrk) 3) The trunk is downed (dntrk) 4) The card is upped (upcd) 


 Workaround: 


 None. Recommend that this sequence not be executed. 


 CSCdr31598


 Symptom:


 This problem is the same as CSCdr41370 in BPX. The average cell per second values for the dspchstat screen does not always reflect the correct transmit rate. It ramps up to the transmit rate, sometimes very slowly, some times more quickly. 


 Conditions:


 This problem will occur whenever the dspchstats command is issued. 


 Workaround:


 For the dspchstats screen, the only values that are incorrect are the "Collection Time", and "Rate (cps)." We can extrapolate this information from the TFTP or USER interval statistics which has a minimum granularity of 5, 10, or 15 minutes based on the number of connections they have in the network. If we divide the "Port Cells Received on Channel" statistic by the interval (5, 10, or 15 minutes) we will get the approximate average CPS. 


 Further Problem Description:


 The root cause was that a timer's initialization was removed by a different defect fix. The result or removing this initialization is that the vcs_cur_ticks timer does not get reset so it contains the last time that the previous response was received rather than when this response was received, so the time value is too large. 


 Then when the average CPS is calculated, since the time value is too large, the average is way to small. It will eventually (over an extremely long period of time) approach the correct value, asymptotically. 


 The sequence is as follows: 


 t = A Normal statistics polling response is received from the card, vcs_cur_ticks is set to now (A). 


 t= B Command clrchstats is issued, which sets flags to drop the next sample (for summary statistics) and to re-init the vcs_cur_ticks field. 


 t = C Command dspchstats is issued, which will cause a statistics poll to be sent to the card and a response to be sent back nearly instantaneously. 


 When the response is received we see that the summary stat filter flag is set so we drop the first response (and we should set the vcs_cur_ticks field at this point but we don't). 


 t = D The dspchstats sends its second poll request, and we get back the response. 


 We update the data for cells RX/TX, etc. 


 We calculate the amount of time this data is for by subtracting the vcs_cur_ticks count (A) from the current time (D) so the time delta is (D - A). 


 Here is the problem. This time value should be (D - C) but because the initialization code was removed it is (D - A), too big. 


 The connection polling rate can be configured to 5, 10 or 15 minutes, therefore the amount of time that this can be off by is 4'59", 9'59" or 14'59". 


 It can also coincidentally be correct if t = A and t = C are very close to each other. 


 CSCdr33931


 Symptom:


 Nether dsplog (it has no record) nor CWM (it didn't receive a trap) when APS active line is in Yellow alarm. 


 Conditions:


 When APS line is in yellow, it is expected to log an entry in dsplog as well as set a trap in CWM. This bug is introduced because of a Release 9.2.32 fix for MR 000253 (CSCdr26613) where the trunk status is set to clear if the active line is Yellow and the standby line is OK. Use the dsptrks command to show the active line status and trigger the trap, unless a clean and easy path is found to send a trap without setting the trunk to the Yellow alarm status. 


 Workaround:


 Use the dspapsln command to monitor APS line status. But do not reroute connections. 


 CSCdr34820


 Symptoms:


 Under certain conditions more than one connection appears to on the same DSP.


 addcon 9.1.1 uvm6 11.1.1  {*}   /* uses DSP 0 channel 0 of slot 9 */


                                 /* DSP 0 ch 0 slot 11 */


 addcon 9.1.2 uvm6 9.1.2   {*}   /* used DSP 0 channel 1 of slot 9 */


 addcon 11.1.2 uvm6 9.1.3   {*}  /* This should be DSP 1 of slot 9,


                                 /* DSP 0 ch 1 of slot 11 */


                                 /* But dchst  9.1.3 shows as using


                                 /* DSP 0 slot 9 */


 Conditions


 Since each DSP supports 2 connections. The dchst command malfunctions when (1) 2nd connection is added to itself (uses both connections on a DSP) and (2) subsequent connection is added to remote node whose first connection was made to the first connection of the originating uvm. The example above describes it best.


 Workaround


 None.


 CSCdr41957


 Symptom: swerr 506 and 589


 Condition:


 Follow the following procedure to produce swerr 506 & 589


 ---------------------------------------------------------


 scp 5 55 05 2 1 2 3 12 c 0 /* Sec Trc Alarm */


 Node 1


 -------


 addyred 2 3


 uptrk 2.2


 addtrk 2.2 (added to some other node, node2)


 addapsln 2.2 3.2 1


 addlnloclp 2.2


 rcp 5


 swerr 506 and 589 are produced


 Workaround: None


 CSCdr49091


 Symptom: 


 If CC traffic is routed over virtual trunks, comm breaks and unreachability will occur.


 Workaround: 


 To avoid this problem if the user is using BXM fw MFC or earlier restrict CC traffic on virtual trunks and allow only physical trunks to carry CC traffic.


 CSCdr52621


 Symptom:


 Enabling channel statistics causes idle time on the node to drop to an unacceptable level. 


 Conditions:


 Occurs when many channel statistics are enabled and/or many connections exist on the node. 


 Workaround:


 None. 


 CSCdr53669


 Symptom:


 ILMI session is automatically active on any port interface. 


 Condition: 


 Enable an interface as a port. Earlier on this interface, there were Virtual Trunks active, which were downed using the dntrk command. 


 Workaround:


 Reset the BXM card. Alternatively, enable ILMI on the port using the cnfport command and set "Protocol by card" option to "Y." Again disable the ILMI on the port using cnfport. 


 CSCdr55450


 Symptom:


 Yellow alarms triggers a flood of swlog 992, which kills ILMI tasks, causing all Axises connected to BPX to go unreachable. 


 Conditions:


 A loose connector causes an Yellow alarm to appear and swerr 992 to appear.


 Workaround:


 The switchcc clears the software log of 992's is ID


 CSCdr56010


 Symptom: 


 CBR connections are missing on three BPX nodes during the upgrade from 9.1.22 to 9.2.23.


 Condition:


 When the nodes were upgraded from 9.1.22 to 9.2.23, this occured once and could not be recreated. The cause for the missing conns are unknown at this time. 


 Workaround: 


 None.


 CSCdr56015


 Symptom:


 SWlog 261 found during the upgrade from 9.1.22 to 9.2.23 


 Conditions 


 SWlog 261 occured once during the upgrade on IGX, and could not be recreated. 


 Workaround 


 None 


 CSCdr58256


 Symptom:


 The BXM Y-red switchover sometimes (observed to be a 1:40 rate) results in a spurious rate matching command cell being sent to the Axis shelf, which might result in an LOS due to a dual SAR failure if the Axis shelf is not at Release 5.0.12 or greater. 


 Conditions:


 Axis Release 4.0.19. BPX running Release 9.2.22. 


 Workaround:


 Upgrade the Axis shelf to 5.0.12 or greater. This is actually the solution to the problem rather than a workaround. The workaround, which does not require an Axis upgrade, is currently (as of 6/12/00) being tested. The crux of the workaround is to create and send Cbus messages to manually remove from the BXM the channels that carry ILMI information to the shelf. Note that since this problem has never been reproduced in a lab, this workaround cannot guarantee that the errant ForeSight cell will be eliminated. 


 1. Use scp to create three Cbus messages. These messages will remove the Axis ILMI channels on ports 1, 2, and 3 from a BXM. 
2. Use xcp to send the proper Cbus messages to the primary and secondary BXM slots where there are Axis shelves are configured on the ports. 
3. Use switchyred on the slot of the primary BXM. 


 There should as little delay as possible between steps 1 and 2 as a sizeable delay could lead to an unreachability with the shelf. 


 The switchyred command will cause the ILMI channels to be restored on both the active and standby BXMs. The hope is that the absence if the ILMI channels will prevent the errant ForeSight cell from being sent to the Axis shelf, thereby avoiding the SAR exception, shelf rebuild and accompanying outage. 


 Here are the details on creating the appropriate Cbus messages: 


 The ILMI channel to Axis shelves is programmed on VPI 3 and VCI 31. The channel number depends on the port number. 


 The formula is: 


 ILMI channel number = <max channels> + MNCH_LMI_CHAN_OFFSET + <port #> where <max channels> is the number of channels listed on the dspcd screen (e.g. #Ch:16320), MNCH_LMI_CHAN_OFFSET = 2 and <port #> is the 0-based port number. The ILMI channel on port 1 of a BXM configured for 16320 channels is 16322. This formula appears in cnfg_trk_sar_chl. 


 The Monarch channel programming Cbus message, 0x52, is used to create and delete the ILMI channel. For port 1 of a BXM configured for 16320 channels, the message looks like this: 


 Fn Code: 52 Op Code: 01 Data: 02 01 01 03 02 3F C2 04 00 


 For port 2 the message looks like: 


 Fn Code: 52 Op Code: 01 Data: 02 01 01 03 02 3F C3 04 00 


 and for port 3: 


 Fn Code: 52 Op Code: 01 Data: 02 01 01 03 02 3F C4 04 00 


 CSCdr70919


 Symptom: 


 The IGX feeder shelf becomes unreachable when configuring LMI protocol to run on the BXM card. 


 Condition: 


 The IGX feeder trunk is connected to the BXM card. An LMI protocol is configured to run on BXM (using the cnftrk command).


 Workaround:


 Do not configure LMI protocol to run on BXM card. 


 CSCdr71781


 Symptom:


 The commands upln/uptrk cause a swerr 3000 error message.


 Conditions:


 When numerous connections are being rerouted and an upln or uptrk command is issued from the CLI.


 Workaround:


 None. To avoid the swerr, issue the commands after the rerouting is done. 


 CSCdr73183


 Symptoms:


 1. The software error log fills with 111s when there are 23 interfaces on the BXM slot. The interfaces may be trunks, port, virtual, or physical. 


 2. The statistics listed below are not being collected on all or some of the trunks/ports on the BXM card. 


 Port statistics: Number of cells received with CLP = 0. Number of cells received with CLP set. Number of cells dscd with CLP = 0 Number of cells dscd with CLP = 0 . Number of cells dscd with CLP set. Number of cells tx with CLP = 0. OAM cells received count Tx OAM cell count Rx RM cell count Tx RM cell count 


 Trunk statistics: Cells RX with CLP0 Cells Rx with CLP1 Cells RX Discard with CLP0 Cells RX Discard with CLP1 Cells TX with CLP0 Cells TX with CLP1 Ingress OAM Cell Count Egress OAM Cell Count Ingress RM cell count Egress RM cell count Total Cells Tx from port BXM: Total Cells RX 


 Conditions:


 This will only occur on a BXM card. 


 When there are exactly 23 interfaces configured on the card, the software error 111s will be logged and the automatic polling for VI statistics (listed above) will completely stop. 


 When there are more than 23 interfaces, then only some of the interfaces on the BXM card will have their VI statistics polled.


 Workaround: 


 Limit the total number of interfaces per BXM slot to 22 or fewer. 


 Further Problem Description:


 This is a ubyte overflow problem. 


 The variable used to track the number of objects to send to the BXM card is a ubyte that has a range of 0-255. 


 The maximum number of objects that the software allows is 250. When a VI statistics poll is created, the following objects are needed: one object per message for the MSG ID, one object per VI for the VI ID, ten objects per VI for the STAT IDs.


 CSCdr78213


 Symptom:


 1. Switch software error 3000 is logged after executing the following commands for NPM and UXM on IGX


      resteccd <slot) (NPM card)


      upln <slot.port> (UXM card)


 2. An error will log in SWSW log file


 3. An error is logged only the first time and did not reproduce if the upln command repeated


 Conditions:


 This occurs in Switch Software 9.2.34 which we are testing. The IGX hardware is involved with the NPM and UXM cards


 Workaround:


 None.


 CSCdr80522


 Symptom:


 Unknown. It is command dependent. For some commands, there may be no problem at all. For some commands, problems occur from logging sw_error to incorrect information display. 


 Conditions:


 This problem might occur only when the User Task (CLI) or the SNMP agent continues to execute some functions after an event is sent to TRNS Task and those functions expect some work will be completed by TRNS. The problem occurs only when these conditions exist and when TRNS calls Pause_proc, and there is not enough work for the Fail Task during the pause. 


 Workaround:


 None. 


 Further Problem Description:


 This problem was caused by an out-of-sync condition between TRNS and UI/SNMP tasks. The problem seems negligible because eventually the work will be done by TRNS. 


 CSCdr81947


 Symptom:


 BCC self-test is not working 


 Conditions:


 The dspmemblk command shows a maximum block size of dynamic memory less than 10k 


 Workaround:


 Use the switchcc commands to isolate scanrgn 2 -t 120 and scanrgn 4 dm dspmemblk dspprf 


 CSCdr82470


 Symptom:


 Port addloclp on the slave side of a daxcon does not work. 


 Condition:


 Cells are transmitted to the network even though the port is loopback. 


 Workaround:


 None. This affects only the slave end of a daxcon. 


 CSCdr83296


 Symptom:


 In the following topology, BPX - BXM - trunk - BXM - BPX, when adding two VTs over this physical trunk and then creating a resource partition on the second VT, the nodes become unreachable. 


 Workaround:


 Unknown.


 CSCdr85197


 Symptom: 


 Two nodes continuously collide during routing.


 Workaround:


 Turn off routing on one node.


 CSCdr86188


 Symptom:


 The 0x52 channel configure message sent for the slave end of an ATM daxcon with the line in Loss of Sig (RED) has the AIS bit set to "01" to generate the AIS message. 


 AIS cells are transmitted to the port even when the line is in LOS. 


 Workaround:


 None. This affects only the slave end of a daxcon with the line in LOS.

Known Anomalies from Previous Releases

The following is the list of known anomalies in previous Switch Software deliveries. Included with each is a brief description of the problem. A more in depth description is available in the release note enclosure of the problem record in Bug Navigator.

Bug ID

Disposition of Anomaly

 CSCdk04032


 Closed. Please see note.


 CSCdk53502


 Closed. There is a hardware limitation that prevents the error reporting and it was determined that fixing this problem could create more errors.


 CSCdm19535


 Fixed in Release 9.2.30.


 CSCdm20593


 Fixed in Release 9.2.31.


 CSCdm24020


 Closed. The possibility of this problem occurring is extremely low and a workaround for the problem exists.


 CSCdm50600


 Closed. Please see note.


 CSCdm60534


 Closed. Please see note.


 CSCdm62985


 Closed. It was determined that this problem could not happen.


 CSCdm78081


 This was found in Release 8.5.05, but despite many attempts, it could not be Release 9.2. This problem is in the 'I' state since it was reported by the customer.


 CSCdm79453


 Closed. It was not possible to reproduce this problem.


 CSCdp08741


 Closed. The capability to burn model A firmware onto a UVM card is no longer supported.


 CSCdp22655


 Closed. This problem could not be consistently repeated, and a workaround exists.


 CSCdp22795


 Duplicate of CSCdr15924, which was fixed in Release 9.3.05


 CSCdp28704


 This anomaly was junked when it was discovered that a file was incorrectly missing a MIB object.


 CSCdp28999


 Closed. Please see note.


 CSCdp32245


 Fixed in Release 9.2.31


 CSCdp33870


 Duplicate of CSCdp32422, which was fixed in Release 9.2.31


 CSCdp34188


 Fixed in Release 9.2.30


 CSCdp34846


 Closed after many failed attempts at reproducing this anomaly. Also, this problem could not be duplicated on different hardware.


 CSCdp37938


 Duplicate of CSCdp34188, which was fixed in Release 9.2.30


 CSCdp57089


 Closed after many failed attempts at reproducing this anomaly.


 CSCdp61204


 Closed. Please see note.


 CSCdp63917


 Closed after many failed attempts at reproducing this anomaly.


 CSCdp65503


 Duplicate of CSCdp76840, which was fixed in Release 9.2.31


 CSCdp72652


 No action is required with regard to the BPX switch's detection or behavior following a bad crosspoint. Automatic switchover would cause more problems than it would solve.


 CSCdp74165


 Closed. It was decided not to add a 9.3 feature to the 9.2 baseline.


 CSCdp81106


 Closed. Please see note.


 CSCdp82740


 Duplicate of CSCdp49749, which was fixed in BXM firmware release MEF


 CSCdp85319


 Duplicate of CSCdm29466, which was fixed in Release 9.2.33


 CSCdp87448


 Closed after many failed attempts at reproducing this anomaly. Failed to detect this problem while reviewing the code.


 CSCdp89369


 Closed. A workaround has been provided. The customer agreed it was sufficient.


 CSCdp90745


 Duplicate of CSCdm24140, which was fixed in 9.2.30


 CSCdp96286


 This anomaly is in the 'I' state. It could not be reproduced with a test version of 9.2.31 and a test version of MEF. More testing is required before closing the anomaly.

Note   These anomalies were closed because they were internally found (and not customer-found). Also, in most cases, they either require significant effort to resolve, are unreproducible, or have a benign effect on the system.

Problems Fixed in Release 9.2.34

Following is the list of fixed problems in the 9.2.34 Switch Software release. Included with each is a brief discussion of the problem.

Bug ID 

Description

 CSCdk55887


 Symptom:


 The dspport command not available to level 6 user IDs. 


 Conditions:


 After upgrading from 7.x software to 8.1+ software. 


 Workaround:


 Increase user privilege. 


 Further Problem Description:


 The privileged level of the dspport command was changed in Release 8.1 to level 2 from level 6. 


 CSCdm13655


 Symptom:


 Cannot free any VCPARMS from the VCPARMS table (limit of 255 has been reached). Tried reconfiguring connections to make them join an existing VCPARMS index, but could not match the parameters successfully. 


 Conditions:


 Only Frame Relay connections are affected. Connections on UFM Model A have variable configurations for VCQ and ECN thresholds. This causes the use of different VCPARMS entries. 


 Workaround:


 Use cnfcon from both ends of connection. 


 Or


 Delete and re-add the connection. 


 Further Problem Description:


 Release 9.1.06 has two defects--CSCdk83358 fixed in 9.1.07 and CSCdk63187 which was fixed in 9.1.10. Both deal with the modification of VC queues. As a result, the VCPARMs indices are not reused. Furthermore UFM Model A has altered VCQ and ECN thresholds creating new profiles. UFM Model B firmware will allow reconfiguring the queues to FRM values. 


 CSCdp50091


 Symptom:


 The data_channel table is not updating with 9.1.15 software code.


 The data_channel table in the SV+ stores information on the HDM/LDM port. Following an upgrade from a pre-9.1.11 release, to a 9.1.11 or higher release the data_channel table is empty on SV+. The node is fine. 


 Conditions: 


 Upgrade from a release before 9.1.11 to a release 9.1.11 or higher. 


 Workaround:


 Configure the port using cnfchutl or cnfchdfm.


 CSCdp67775


 Symptom:


 APS does not clear last user request after SF switch. 


 Conditions:


 Jan. 1999 edition of GR-253-CORE (issue 2, Revision 2, section 5-92).


 Workaround:


 None


 CSCdp93955


 Symptom:


 The swerr 532 is logged while doing snmpwalk or snmp MIB browsing. 


 Condition: 


 BXM feeder trunk with Y-red pair and secondary card is active. 


 Workaround:


 1. Ignore swerr and clear error log or


 2. Make Primary active or


 3. Avoid snmpwalk for condition mentioned above. 


 CSCdr08430


 Symptom:


 The cnftrkparm does not alter non-TS transmit queue size correctly. 


 Condition:


 NTM subrate trunk (with number of DS0 <= 8) and cnftrkparm is issued to increase NTS Q depth to either 84 or 85 (maximum) for an added trunk. 


 Workaround:


 Limit NTS queue depth to 83. 


 CSCdr09440


 Symptom:


 ASI Qbin configuration is lost during Y-red switch-over to secondary card. 


 Condition:


 This problem will occur when the ASI Y-red Secondary Card is active. 


 Workaround:


 Switch back to Primary Card.


 CSCdr11698


 Symptom:


 The overbooked Frame Relay connections caused TS discard. 


 Conditions:


 While running both an LDM and HDM connection with two Frame Relay connections, both Frame Relay connections are overbooked, so they can utilize full trunk bandwidth when no LDM/HDM traffic is traversing the trunk. 


 When there is both LDM and Frame Relay traffic running across this trunk TS Qbin discards are seen. 


 Workaround:


 1. Do not overbook or 


 2. Route some connections to other trunks if available.


 Further Problem Description:


 The problem is seen only when the Frame Relay connections try to utilize all the trunk bandwidth due to the connections being overbooked. 


 CSCdr11823


 Symptom:


 Potential problems in connections setup using VSI controller (either PNNI controller or an MPLS controller) if the connection uses VPI=1, VCI=257. 


 Condition: 


 A VSI-based connection uses VPI=1, VCI=257, and BCC self-test is enabled using the cnftstparm command. 


 Workaround:


 Disable BCC self-test using cnftstparm command. 


 CSCdr15924


  Symptom:


 Robust Mechanism causes unpredictable handling of APS information with multiple CWMs. The BPX is not sending APS robust alarm messages to CWMs for multiple APS events. APS events are being lost. The BPX sends only APS robust alarm messages to one CWM. 


 Conditions:


 The problem of the BPX not sending all events happens when multiple events happen in a short span of time. The problem with sending only the APS robust alarm message to one CWM will always happen. 


 Workaround:


 None.


 Further Problem Description:


 The robust alarm mechanism currently used needs to be enhanced for APS robust alarm messages in order to handle multiple APS events occurring in a short period of time. Also a fix needs to be made to allow the BPX to send APS robust messages to all attached CWMs. 


 CSCdr20925


 Symptom:


 No redundancy after certain events occur. 


 1. Frame Relay connection from UFMU card in same chassis working well over UXM to UXM -red trunk. 


 2. Y-red trunk fails and moves to standby, with connection still working normally. 


 3. Trunk forced back to primary in Y-red. If the pair is using dncd or resetcd the connection fails to pass traffic. 


 No errors logged in node logs. The dsplog, cderr, swlog, and dsptrkstats show OAM and BDataB traffic stopped only. High priority cells still traverse trunk. 


 Workarounds: 


 Delete and re-create connection or try rrtcon. 


 CSCdr21739


 Symptom:


 Trns Handler uses up most of the CPU, many connections fail to route, but Trns keeps on trying. 


 Conditions:


 Trunk failure reduced available bandwidth. 


 Workaround:


 Turning off routing (off1 11).


 CSCdr22568


 Symptoms:


 ILMI protocol keeps running on the BXM card even after disabling it using cnfport command. 


 Conditions:


 The problem occurs only when all of the below conditions are true. 
1. Enable ILMI for a port on the BXM card. 
2. Disable ILMI by issuing cnfvsipart, than cnfport commands.
3. For cnfport, Enter N for the option protocol by card.


 Workaround:


 Disable ILMI protocol on the port. Let the protocol run by the card which should be set to YES. 


 CSCdr23432


 Symptom:


 Node ABORT occurs in addjob.


 Conditions:


 With ATM Port, run Addjob to configure existing ATM Port as Frame Relay port and all the parameters are not given in the same line.


 Node aborts when you try to add a job to configure EXISTING ATM Port to Frame Relay port. This does not affect other commands like configure port (ATM/FR) ONLY ADD JOB or adding job to configure nonexisting port or add job to configure ATM port of an existing ATM or Frame Relay port, or add a job to configure existing Frame Relay to Frame Relay Port. 


 Workaround:


 Do not add job to configure existing ATM port to Frame Relay port. 


 CSCdr25318


 Symptom:


 When the UFMU port is up, upon removal of the back card, the port status is still active. It should be FAIL.


 Conditions:


 In all previous switch software, which support UFMU cards, this problem exists. 


 Workaround:


 Install UFMU with any type of back card. Using upport, remove the back card, check the port status. It should still be ACTIVE. 


 Further problem: The port status is sent to CWM by robust message, for old SWSW without the fix, it may cause problems in CWM if CWM just check the port status, without checking the back card missing alarm, to do some other configuration such as addcon, addtrk. In old SWSW, the card missing is checked before addcon. 


 CSCdr27853


 Symptom:


 Value of the reroute timer displayed in cnfcmparm after clrallcnf or clrcnf is 0 seconds instead of the default of 3 seconds. 


 Conditions:


 This problem is created by clearing the configuration with clrallcnf or clrcnf. 


 Workaround:


 Use cnfcmparm 9 to set the reroute timer value. 


 Further Problem Description:


 Problem is due to using different units for reroute timer value during initialization and modification. After clrallcnf or clrcnf, the reroute timer is initialized to default number of three seconds. Whereas cnfcmparm treats the value as number of ticks. So, for a default value of less than number of ticks per second (100 ticks/sec), cnfcmparm displays reroute timer value as zero. When the reroute timer value is set using cnfcmparm, conversion to number of ticks before updating the reroute timer solves the problem. 


 CSCdr32789


 Symptom:


 Gateway LCNs count may exceed trunk channel count if cnfrsrc is done at BXM and trunk channel is reduced below gateway LCNs. 


 Condition: 


 It happens only in the above scenario. 


 Workaround:


 Configure the trunk channels and gateway LCNs at the UXM end (using cnftrk). 


 CSCdr33428


 Symptom:


 UXM mismatch occurs following a card rebuild.


 Condition: 


 1. Reset controller card with a standby UXM in the node 
2. Activate UXM, which has the number of channels smaller than 8000. 
3. Remove and reinsert UXM card (or reset UXM card).


 Workaround:


 Deactivating and reactivating the card will clear the problem. 


 CSCdr36808


 Symptom:


 SPVC reroute fails even though there are still some resources.


 Condition: 


 When a trunk is changed from VSI-only to non-VSI only trunks and vice-versa. (VSI-only trunk is a trunk on which at least one VSI partition uses VPI<=1. Non-VSI only trunk is a trunk on which none of the VSI partitions uses VPI<=1.) 


 Workaround: 


 Reset the BXM card on which the trunk is configured.


 CSCdr36819


 Symptom:


 The following is applicable only to BXM cards


 1) deltrk <port #> 2) dntrk <port #> 3) Upln <port #> 


 If BXM firmware supports CC traffic control feature, a) It reserves the stats reserve value configured on any trunk as the bandwidth on HPQbin 2 of the VI corresponding to the trunk. This is on the egress side. b) The above stats reserve value will be sent to the card while doing uptrk and whenever there is a change in stats reserve. 


 During dntrk, though switch software sends the VI deactivation message, it is not freeing up the bandwidth (stats reserve) configured already. 


 If the same port is upped as a line, the same Qbin 2 will be used for nrt-VBR traffic. Whenever a new connection (rt-VBR) is added, its bandwidth will be accumulated on top of the old bandwidth (which is not freed during dntrk). This may affect the traffic on this port depending upon the PVCs setup. 


 Condition: 


 This will happen only if the same port that was used as trunk and upped as a line. The sequence is as follows:


 1) deltrk <port #> 2) dntrk <port #> 3) Upln <port #> 


 Workaround:


 Resetting the BXM will solve the problem. 


 CSCdr38707


 Symptom:


 Control VC establishment failure occurs in ports.


 Condition: 


 Total sum of VSI bandwidth on all interfaces on the card exceeds the OC-12 bandwidth of 1412830. 


 Workaround:


 Reconfigure the VSI bandwidth on the various interfaces on the card, so that total VSI bandwidth does not exceed OC12 bandwidth. 


 CSCdr41814


 Symptom:


 From SNMP, addshelf and VSI partition using the same VPI can cause a commbreak. 


 Condition: 


 The addshelf (IGX, AXIS, or PAR) from SNMP to SNMP, configure VSI resource to allow VSI range to cover VPI = 1 and/or 3. 


 Workaround:


 None. 


 CSCdr48340


 Symptom: 


 The dspnw on a node with IMA virtual trunks causes swerr 1423 or 1M3 abort 


 Conditions: 


 IMA virtual trunks are present on the node and are added to the network. Also, the node names are 5 or more characters long. 


 Workaround:


 Reduce the node name to four characters or fewer Or, if possible, delete the IMA virtual trunks from the network. 


 Further Problem Description:


 The problem occurs due to an overflow in the display screen of dspnw. Even though it looks serious, the problem is limited to the display and there are no database corruptions. 


 CSCdr49264


 Symptom:


 Add/Modify rt-VBR connection with "Enable cell routing" gives a false value via CWM. The connection type is shown as nrt-VBR on the CLI screen. 


 Conditions:


 This happens in switch software 9.2 and 9.3 using CWM 10.0 or SNMP script. 


 Workaround:


 1. Connect CWM to BPX network. 
2. Use CWM or SNMP scripts to add or modify a rt-VBR connection. The "Enable cell routing" for this connection is false. Check the new or modified connection on CLI using dspcon; the connection type is nrt-VBR. 


 CSCdr49301


 Symptom:


 After a trunk went down or up, several PVCs did not reroute due to inconsistent LU at the endpoints. 


 Available bandwidth throughout the network verified support of the reroute. Attempts to reroute these conns were unsuccessful. 


 Conditions:


 This is observed when rerouting has to take place after some network activities (such as, trunks going down). 


 Prior to this, the network operator has reconfigured some connections (via cnfcon), and those transactions were incomplete. Warnings about the incomplete cnfcon transactions were not always provided to the operator. 


 Workaround:


 If the connection does not reroute due to inconsistent load unit, the following workaround (as an alternative to delcon and addcon) can be used: 


 At either end of the connection, preferably at the master end, issue a cnfcon command with a slightly different set of connection attributes (such as 99 percent utilization instead of 100 percent, 56 cells instead of 50, etc.). Then issue another cnfcon command with the exact desired set of attributes. Finally, issue a rrtcon for that failed connection at the master end, to kick-start this semi-permanently failed conn into rerouting. 


 CSCdr51105


 Symptom:


 An swerr 30 is logged when a UXM card is inserted. 


 Conditions:


 The problem occurs rarely. It is caused by a race condition that has not been identified. The fix can recover the problem gracefully without a logged error. 


 Workaround:


 Resetting the card can fix the problem (sync up the database). 


 CSCdr56249


 Symptom:


 Physical transition counters like LOS, LOF (displayed via dspcntrstats) are updated inconsistently when the corresponding errors are seen. 


 The counters on the right side of the dsplnerrs and dsptrkerrs screen are updated inconsistently when the corresponding errors are noticed. 


 Conditions:


 The following conditions are needed for this problem to occur. 


 1.A trunk or line is up on a BXM card. 
2. A failure occurs at the physical layer and an integrated alarm is declared. 


 Workarounds: 


 Configure the threshold time for a RED alarm to be declared, to be greater than 10 seconds (Line polling rate). This is the amount of time the condition has to persist before an integrated alarm will be declared. 


 The inconsistent updating of the counter statistics has been fixed. The customers will still not see any updates in the dsplnerrs/dsptrkerrs related counters. 


 Further Problem Description:


 The transition counters like LOS, LOF, YEL, AIS displayed using the dspcntrstats command measure the number of transitions into & out of their corresponding conditions. These statistics are reported to switch software using the 0x56 message. When switch software gets this response, it updates the corresponding databases and this is seen via dspcntrstats, dsptrkerrs or dsplnerrs. 


 However, when the condition persists for 2.5 seconds (or whatever the threshold is configured to via cnflnparm/cnftrkparm), an integrated alarm is declared and the FW sends a 0x55, opcode 5 trap msg to switch software to declare an alarm. After the line goes into integrated alarm, these transition counters will not be updated. 


 If the condition persists for less than the threshold time, since the line or trunk is not in alarm, the bits are not set and the transition counters are updated. 


 The statistics displayed via the dsplnerrsor the dsptrkerrs command are related to statistical alarms and will be updated only if the line or trunk is not in alarm. For transient conditions that don't persist beyond the alarm-declaring threshold time, these counters are updated. 


 CSCdr58725


 Symptom: 


 UXM card in standby mode will continuously be reset


 Condition: 


 Self-test frequency (in cnftstparm) is set to a very low value, such as 1 second, but happens for values typically LESS THAN 40 seconds. 


 Workaround: 


 Do not set this frequency to LESS THAN 40 seconds. The 300 seconds default value works OK. 


 CSCdr64725


 Symptom:


 Incorrect operational status is reported for a trunk or virtual trunk via SNMP. 


 Conditions:


 When a trunk/virtual trunk is added, the wrong status is being displayed from a CWM GUI. 


 Workaround:


 None. 


 CSCdr67236


 Symptom:


 The BXM card's system time will not sync with network time. 


 Condition: 


 This will occur only if there is a change in network time (Via cnfdate cli) and if there is no ESP feeder on the node (this is obsoleted in 9.2). 


 When there is change in network time, the software is sending "time change event" (0x0a/0x50) only if there is any ESP feeder on the node. 


 Workaround:


 Resetting the BXM card will trigger a 0x50 message. Please note that this event is a service affecting one. Alternately, for redundant BCC configurations, a switchcc will ensure that 0x50 message is sent to all the BXM cards after switchover. This will sync up the time between the BPX and the BXM cards. 


 CSCdr75146


 Symptom: 


 Connections do not route due to lack of LCNs. Constats shows No LCN Failures incrementing on the endpoint or via node. dspload will show that conids are available on the trunk the connection is trying to use. This may occur on an endpoint or via node, hence the problem node must be identified. 


 Conditions:


 None. This can occur in any version of switch software in any configuration. 


 Workaround:


 Using switchcc on the problem node will correct the problem. 


 Further Problem Description:


 If the problem trunk is a BXM, dspchuse will show that all the LCNs on the trunk are used, field pvc used will equal field pvc configuration. This problem was observed just after upping/adding a trunk with uptrk and addtrk as the channel count was not initialized to zero on the uptrk. Performing an upln followed by a dnln prior to upping the trunk will initialize the channel count to zero and avoid the problem. 


 CSCdr79123


 Symptom: 


 A connection could be routed over a path with too much delay.


 Workaround: 


 Configure preferred route.

Problems Fixed in Release 9.2.33

Following is the list of fixed problems in the 9.2.33 Switch Software release. Included with each is a brief description of the problem.

Bug ID

Description

 CSCdj14920


 Unable to clrcnf on BPX node whose number is > 63


 CSCdm04491


 Swerr 921 flooding


 CSCdm13655


 VC bw parm is not reused (initialized differently during upgrade vs provision).


 CSCdm29466


 Cannot addtrk on the VSI network because of VPC conid mismatch


 CSCdm31518


 "Active CC failure (EEPROM, SAR) and standby unlock or reseat causes rebuild."


 CSCdm38578


 Echo Negotiation for telnet between AIX and BPX


 CSCdm48790


 SIU phase errors from all BXM cards in a node


 CSCdm69629


 Different values of statistical reserve for dsptrkcnf and dspload


 CSCdm88055


 Job run job experienced failed


 CSCdp20486


 UXM IMA physical line alarms are not sent to SV+


 CSCdp50871


 UP/Down Line on ALM-A behaves erratically.


 CSCdp53961


 Control card mastership error not properly detected by software


 CSCdp58131


 SNMP get function in atmTrunkStatsTable


 CSCdp62387


 APS Clear Trap 20100 does not distinguish various types of clear events.


 CSCdp68440


 Swerr 961(BAD_LCN_SPECIFIED) found after dnport/dnln


 CSCdp72012


 Swerr 129 (BAD_TYPE_LOGGED) found at BPX2


 CSCdp73065


 Background Tst card errors on active. Card has state ACTIVE-F w/ss


 CSCdp73606


 Port LED remains on when line is downed on UXM.


 CSCdp78731


 LCN and VPC conid count is not sending correctly in TBL


 CSCdp83180


 Swerr 614 AUTO_DEL_LCON and 612 AUTO_DEL_VC upon fallback from 9.3.0L


 CSCdp83902


 UVM Line pass through does not work on the second physical line on UVM


 CSCdp87624


 Autodel trunk when rebuilding a port with 32 vtrks


 CSCdp93368


 When up a line then switch software seems to program all cons on that card


 CSCdp93728


 Summary statistics overflow is not detected correctly for Port and VI stats


 CSCdp94039


 Swlog 2000 occurs when snmpwalk on an IGX node


 CSCdp95286


 Cross point failures on the bcc.


 CSCdp95807


 Robust object message for vtrunks appears to be reporting wrong channel count


 CSCdp96768


 VSI and SVC bandwidth is not eliminated while configuring egress hpqbn b/w.


 CSCdp98970


 VT session timeouts on particular page when running dsprts


 CSCdp99622


 "Burn UXM/FW using C-bus, gets aborted"


 CSCdp99780


 Inhibit line loop diagnostics for IMA line/trunk


 CSCdr00360


 A Tstdelay command cannot run while card is initilized


 CSCdr04828


 IP relay channel is not getting deprogrammed when AAL/5 feeder is deleted


 CSCdr06086


 A dsp_pa_fail0 switch statement falls through when it should not.


 CSCdr06280


 Conditional update should not be integrated for a trunk between T1 and E1


 CSCdr08084


 A 62 message is not send on addyred if the secondary card is running self-test


 CSCdr08231


 A clrtrkstats does not clear Trunk Qbin statistics


 CSCdr08952


 A addloclp on BNI feeder connection aborts a node under certain circumstances


 CSCdr10473


 A swerr 1012 (BAD_RS_NCHANS) occurs after hitless rebuild


 CSCdr11310


 Configure LMI on UXM port causing swerr 987


 CSCdr11823


 A non-Fatal card error occurs on red. BXM during PXM1 upgrade. Refer to bug CSC46785


 CSCdr11837


 The maximum channel limit for dspchoid command is incorrect


 CSCdr12300


 Switch MIB is inconsistent with the CLI


 CSCdr14544


 PNNI VPI.VCI 0.18 is blocked when path 0 is built on BXM.


 CSCdr14558


 Switch software updates wrong port DB and robust message after Y-Red UFM switch over.


 CSCdr14935


 Unable to add UFM UXM connections from UFM side and there is corruption of Be Bc.


 CSCdr17056


 Provide UNKNOWN state for serialPortLeadState


 CSCdr19348


 NTS connections get bit errors when Frame Relay bursts fill up trunk capacity


 CSCdr20760


 Incorrect prompt while deleting a trunk on IGX UXM card


 CSCdr21739


 Node hung up and lost access after deleting a trunk.


 CSCdr26582


 CD error after issuing a addctclr command (SLT)


 CSCdr30234


 Available Conids gets updated only on the nodes connected by the trunk.


 CSCdr32875


 "int_all_usr_updt, trkchans: kicks of reroute only for trunks attached locally."


 CSCdr41370


 Dspchstat from Port counter slowly ramps-up to send rate

Problems Fixed in Release 9.2.32

Following is the list of fixed problems in the 9.2.32 Switch Software release. Included with each is a brief description of the problem.

Bug ID

Description

 CSCdk03916


 Trunk information is inconsistent


 CSCdr26613


 "When active APS line has YEL, trunk fails."


 CSCdr35085


 Switchcc cannot be cancelled when updates pending

Problems Fixed in Release 9.2.31

Following is the list of fixed problems in the 9.2.31 Switch Software release. Included with each is a brief description of the problem.

Bug ID

Description

 CSCdk15523


 "Integer overflow results in computation in get_bc, get_be funcs"


 CSCdk22052


 Switchcc event logged under trapd.log when the command is cancelled


 CSCdk45354


 No data continuity between UVM & HDM for nx64 connection


 CSCdk60213


 HDM data errors with 1152 kb/s connections on 9.1.06


 CSCdm10213


 After upgrade or switchcc in 9.1, extra connections may appear


 CSCdm20593


 Switch software should not allow an ATFR connection between two UXMs


 CSCdm26083


 Dsptrkbob causes swerr 30 and 923 when performed on sec Y-Red card


 CSCdm46032


 SNMP identifies ALM/A line as ATM trunk


 CSCdm47765


 VT cause memory leak


 CSCdm68968


 "VC-Q depth setting at default value, Connection Manager, IGX, routing and feeder node"


 CSCdm75577


 UFM-C to BXM SIW/NIW connection discards 100% cells at BXM on BPX if the connection is between UFM-C on IGX to BXM on BPX.


 CSCdm77271


 Incorrect modem upgrade support


 CSCdm87788


 Unable to add connection with maximum rate on BXM-T3 port with direct mapping


 CSCdm91529


 "Screen flicker on dspnds, with more than 2 columns nodes"


 CSCdp07967


 Statistics files updating standby cause standby to hang in update state


 CSCdp09854


 The value for maximum pvc bw in rsrc partition displays wrong value


 CSCdp15350


 SNMP GET-NEXT does not work for frLportStatTable


 CSCdp20534


 Uninitialized variable in get_rrt_space() function


 CSCdp27598


 Disabling and enabling echo canceller produces Channel Pair Problem


 CSCdp32245


 BXM-OC3 DX performance monitoring is not implemented Bellcore 253 Sec 6.2.2.


 CSCdp32422


 addlnlocrmtlp does not loop traffic properly in APS 1+1 cross over circuit


 CSCdp32490


 Secondary CC went from UPGRADED to STANDBY after pull/reinsert CC-backcard


 CSCdp32760


 Updates/Upgrades of circuit lines can cause a memory leak on the standby


 CSCdp32823


 IGX FAIL handler causes high CPU utilization


 CSCdp34687


 BPXs running 9.2.22 experiences commBreak every 5 seconds and cleared.


 CSCdp34935


 connCurrRouteDesc description inconsistent with code


 CSCdp35155


 LDM cderrs and card failed in 9.2.3M


 CSCdp37572


 Addcon command does not include connection display


 CSCdp39883


 Con with 1/101 VPI/VCI added at BXM fdr trunk caused UNRCH of its fdr


 CSCdp41410


 Modem Silence duration can be set to a maximum of only 5.1 seconds


 CSCdp42776


 Cannot configure BXM port by runjob command


 CSCdp43913


 Dsprsrc displays confusing information about Topo Discovery


 CSCdp45833


 SVC deletions are sometimes incomplete (swerr 332 with FFF1)


 CSCdp47053


 ALM/B Y-Red does not work for upgrade 8.5.09->9.1.15->9.2.23


 CSCdp47428


 IFC failed when shelf is re-added (with 2 partition)


 CSCdp47479


 Unable to configure feeder LMI timers


 CSCdp48792


 "The dsplog/trapd show the APS alarm cleared, but dspapsln is in LOS"


 CSCdp48797


 All connection parms go to 0 when change vc q depth


 CSCdp48797


 All connection parms go to 0 when change vc q depth


 CSCdp49215


 Addtrk on Y-red card causes swerr 9082


 CSCdp49860


 Dncon causes other connections to be downed


 CSCdp49951


 BPX hanging up with TUNL task using up to 60% CPU RT


 CSCdp50593


 Updated information PNNI ctrlr not sent after addctrlr command


 CSCdp51318


 No alarm of the APSLN in dsplog/dspapsln after Signal Degrade/Failure


 CSCdp52802


 UVM ports do not pass data due to stuck CCS conditioning


 CSCdp53212


 Dspload from IGX on a remote BPX with trunk no.> 8 is not allowed


 CSCdp53891


 Addloclp and addrmtlp command causes yellow alarm on UVI interface


 CSCdp54106


 "BCC switchcc causes Comm failure, telnet failure"


 CSCdp54803


 BCC switches over when standby is in update statistic with bad Spurious Int


 CSCdp55388


 Dspchuse shows wrong number for max PVC configured.


 CSCdp55442


 Addjob/editjob and cnfport corrupts memory or can cause a 1M3 abort


 CSCdp58545


 Distortion on UVM-to-CVM connections routed on UXM Trunks when VAD Threshold reached.


 CSCdp58869


 Unintelligent response from cnfcon command


 CSCdp59960


 UVM does not send yellow alarm to PBX when it receives a yellow alarm from PBX


 CSCdp61539


 "Networking channel deletion problem for Transparent, Blind and Inter-nodal"


 CSCdp64345


 Virtual trunk in comm fail is chosen by route or after hitless rebuild


 CSCdp65187


 Multiple switchyred within 10 seconds causes line to go in LOS for APS


 CSCdp66930


 No failed traps for user lockout but traps for BPX lockout


 CSCdp69003


 "Decrease Comm Brk clear, reroute and recondition time after rebuild"


 CSCdp69582


 Unable to switchyred on upgrade from BXM to BXM-E due to Qbin size mismatch


 CSCdp70093


 Failure configuring VSI ILMI gives error message Unknown error for LCN un avail.


 CSCdp70295


 "UNI port MIB should show range 1-255, not"


 CSCdp73719


 ILMI on card can be disabled through SNMP even if VSI ILMI enabled.


 CSCdp76840


 Resetcd on Active should warn when standby is still in PRGM mode.


 CSCdp79429


 Dspselftst shows test attempts incrementing yet Status always shows Not Run


 CSCdp79560


 TFTP Channel Stats are not reported correctly


 CSCdp79719


 Cnftrk on an IMA trunk shows negative transmit trunk rate!


 CSCdp82720


 Y-red: standby UXM does not take over when FW is burned on active card


 CSCdp84848


 Dsplogcd for a VSI trunk attempts to use an uninitialized pointer


 CSCdp85171


 Flood of HW failure messages from BXM caused node rebuild


 CSCdp85238


 Alarm are not getting updated when delapsln and switchyred/resetcd is done.


 CSCdp86269


 Trunks and LNs on aps cds go into LOS and never recover during gr253 -> ITUT.


 CSCdp90123


 Cnftrk for a vtrk on an OC12 interface gives a line coding prompt


 CSCdp90130


 Cnfrsrc shows more bandwidth than the physical maximum for a feeder.


 CSCdp98715


 Swlog 514 and 589 when doing dncon.


 CSCdr00072


 Using unitialized num_ports variable in av_bkcd()

Problems Fixed in Release 9.2.30

Following is the list of fixed problems in the 9.2.30 Switch Software release. Included with each is a brief description of the problem.

Bug ID

Description

 CSCdk36040


 "Trap 20004-wrong value for varbind trapCardType, FRP back card"


 CSCdk53336


 Tstdelay not working on non-enhanced ASI-155


 CSCdk87939


 Dspchcnf shows inconsistent information after upgrade to 9106


 CSCdm05502


 Need cnfuvmchparm parameters 8 and 9 to configure UVM echo cancelers


 CSCdm19532


 A-bit status not propagating through network changing from NNI to UNI port


 CSCdm19535


 Channel program problems for BXM virtual trunks


 CSCdm24140


 Delcon on IGX causes IDLE RT to drop


 CSCdm31990


 CVM cbus message (0xA0) is not delivered when the secondary card is active.


 CSCdm42254


 When user ID is deleted subsequent users are reported one off.


 CSCdm53182


 Swerr 923 logged when dsptrkred command is used.


 CSCdm65380


 Allow conids lower than 4096 for VT wraparound


 CSCdm72719


 Unable to add BNI VT over ASI port in some cases


 CSCdm74224


 Unable to configure a port on OC-3 card when others are already configured.


 CSCdm85764


 "IGX node logging constant swerr 2051, TFTP_FILE_SIZE_ERR"


 CSCdm85783


 Five connections were deleted. software errors 614/612/534 were logged during a full rebuild


 CSCdm86633


 Swerr 332 (BD_XLAT_INDX) and 325 (BD_XLATDB_REF) on VNS SVCs


 CSCdm88262


 Able to add atfr DAX conns from frm.xx - uxm.xx with pcr < 50 and policing: on.


 CSCdm91238


 SWerr 2003 is seen during a switchcc


 CSCdm91631


 During ungraceful upgrade from 9.1 to 9.2, some BW PARMS can become allocated


 CSCdm92021


 Error_slot were used instead of next_slot when checking next_slot parity error.


 CSCdm92790


 Voice and NTS IGX traffic is serviced in VBR Q of BXM


 CSCdm93670


 Cannot configure 2 OC3 trunk has 7K PVCs


 CSCdm93701


 PVC shows inconsistent prefer route information


 CSCdm94587


 Swerr 532 and 923 when deltrk of trunk on downed card


 CSCdp00060


 Swerr 526(NEG_FILL_REQ)


 CSCdp01511


 "FRM - FRM, 2 seg. conn has cbr traffic type"


 CSCdp02203


 Could not add 3 seg. FR-FR connection from CM GUI (FRM - FRSM)


 CSCdp03317


 VT Path Failure condition remains after the downed VPC in the cloud


 CSCdp04213


 "Software error 3025 gets logged thrice, when do a walk on atmPortStatLmiStatAc."


 CSCdp05149


 1 mil 2 abort after full rebuild on N33


 CSCdp06823


 SW9082 after switchcc and tstconseg


 CSCdp08636


 BPX node showing a trunk connected to itself instead of popeye feeder


 CSCdp11851


 CMUP timeouts have to be increased to avoid thrashing


 CSCdp12024


 BPX sends wrong error messages to CWM


 CSCdp12505


 Memory should be moved from Pool Region to Hitless Region


 CSCdp14002


 Trunk fail/repair resets Concentric Comm Break Clearing etc.


 CSCdp15671


 Software error 105


 CSCdp15712


 Can not add con with certain VPI.VCI value


 CSCdp16760


 SWERR 3033 seen on BPX nodes


 CSCdp16891


 SWERR 532 seen on BPX nodes


 CSCdp17303


 Lines do nor show up in CWM 9.2.06M for certain BXM-E3/T3


 CSCdp18093


 Continuous BUS A|B Reports PRI LOSS (Clock) log messages when primclksrc = VT


 CSCdp18160


 False NNI failure indication at IGX FDR endpoint


 CSCdp20894


 Addlnloclp/dellnlp causes trunk Mgr Ret Yel and LOF (RED)


 CSCdp20961


 Swerr 5019 occured during loadrev and runrev 9.2.3F


 CSCdp21688


 Sec BXM card goes in mismatch during upgrade(9.1-9.2) when cards not in service.


 CSCdp21803


 Trapd log reports event trap on wrong node


 CSCdp23116


 "Continuous hitless rebuilds, if 1st abort is before hitless pointer"


 CSCdp23196


 Swerr 1101 (BAD_EVENT_TYPE) logged.


 CSCdp23410


 UXM physical trunks with VPI of 0 does not work


 CSCdp24319


 Dspcon for atfst connections does not display all parameters on second page


 CSCdp24366


 get_trunk() does not properly handle physical slot/logical slot mapping


 CSCdp25420


 A line which is upped can be configured as an IMA trunk


 CSCdp25685


 Software error 1012 logged upon a delshelf on a VSI trunk


 CSCdp26827


 Swerr 9082 logged for the nrtVBR conn 3.4.255.32852


 CSCdp27775


 Unable to add IGX feeder


 CSCdp30654


 LCN allocation issue with crosspoint test


 CSCdp31596


 IGX 9.2.22 NTM does not support FST in traffic class failing addtrk


 CSCdp32058


 Send CM update responses to unreachable nodes


 CSCdp32815


 Dspvsipartinfo display hangs; an issue for automating the testing


 CSCdp34188


 No continuity on a con routed over a BXM FDR to a IGX feeder


 CSCdp35713


 Channel for NW use counted twice


 CSCdp39714


 Move disabling of VPC conns upgrade to 9.2.30 from 9.2.23

Problems Fixed in Release 9.2.23

Following is the list of fixed problems in the 9.2.23 Switch Software release. Included with each is a brief description of the problem.

Bug ID

Description

 CSCdm64323


 Swerr 3005 BAD_DEFAULTS seen on two BPX nodes.


 CSCdp25375


 Abort does not cause hitless rebuild or switchcc (full rebuild instead)

Problems Fixed in Release 9.2.22

Following is the list of fixed problems in the 9.2.22 Switch Software release. Included with each is a brief description of the problem.

Bug ID

Description

 CSCdp04046


 Increase cm update time-out from 30 seconds to 90 seconds


 CSCdp05661


 Node is unreachable from one side but the route is fine


 CSCdp10383


 Tftp file stats for PHYSLINE object reports all ports as zero

Problems Fixed in Release 9.2.21

Following is the list of fixed problems in the 9.2.21 Switch Software release. Included with each is a brief description of the problem.

Bug ID

Description

 CSCdj57458


 Reduce privilege level for dspqs command


 CSCdj79112


 BXM does not allow SCR/CIR less than 50cps/19.2kbps


 CSCdk26279


 Block a user from disabling CAC override if ATM port is over subscribed


 CSCdk34722


 Enable EPD configuration on all BXM queues. Allow clp-lo > clp-hi. (UXM)


 CSCdm06156


 "Sim-fdrs on BNIs are unreachable after rebuild, bad loopback rebuild"


 CSCdm19696


 BME port configure is blocked need to set CAC override and shift on/off


 CSCdm36041


 "When active BCC backcard is removed, no info to dsplog"


 CSCdm38356


 100% Cell Loss on ALM/A VPCs (GW_TYPE_CELL_VPC) routed over ALM/B trunks


 CSCdm40129


 Crosspoint test failing on some BXM trunk test cases


 CSCdm46335


 Swerr 9091 on BPX node due to a tstdelay failure


 CSCdm46537


 Addcon does not check egress load with cac override disable and %util enable


 CSCdm47933


 Output of dspnds -d is larger than screen and columns wrap around


 CSCdm51607


 Print function is not working correctly (format issue)- ok 8.4 & broke


 CSCdm52681


 Switchyred causes data transfer stops for 1 to 4 minutes


 CSCdm58441


 Dcdrtbl on UXM card logs a BAD_CD_TYPE (55) swerr


 CSCdm58804


 Swerr 8096 logged on IST n/w for nightly jobs


 CSCdm60541


 Software error 919 (BAD_SVR_CNTR_PTR) was logged on BPX node in IST n/w


 CSCdm61885


 During a burnfwrev in a UXM card, it does not shows as program


 CSCdm62078


 Swerr 986 occured during cnftrk virtual trunk


 CSCdm63072


 Software errors 31 and 52 with addlocrmtlp where remote end is BPX feeder


 CSCdm63583


 DSPCONS -FABIT sometimes shows A-bit status incorrectly as UNUSED


 CSCdm64034


 Hitless rebuild count is not getting incremented


 CSCdm64066


 Tstdelay on the UXM conn fails reporting with state table hung


 CSCdm64811


 APS: switchyred causes LOS for 10 seconds


 CSCdm65813


 APS: switch back to working line incorrectly.


 CSCdm68729


 AIS getting generated on remotely looped back connections


 CSCdm70167


 Software error 104 after loading 9.2.2L


 CSCdm71616


 Cannot delete link from UXM-IMA virtual trunk


 CSCdm73852


 Feature mismatch may not be working for 1 port group BXM cards


 CSCdm74630


 Swerr 1415 logged in BPX


 CSCdm76753


 Shorten the error string displayed for supported load types for trunk


 CSCdm76881


 "Addyred not possible when upgrading from 8.4.21 to 9.1 or 9.2, in on"


 CSCdm77070


 Alarm-a line VPC mode can be changed when there are VPC cons on it!


 CSCdm77509


 AXIS feeder shows incorrectly as a MGX feeder


 CSCdm80991


 Unable to add conns using CM GUI with BPX 9.2.20 & MBE firmware


 CSCdm83096


 Failed to addyred on LDM: RCMP entries mismatch


 CSCdm89320


 BPX lmi messages to AXIS shelf do not contain correct I.E.


 CSCdp05584


 During 9.1->9.2 upgrade, user connection channels are allocated for cc traffic


 CSCdp05865


 BXM-E3/T3 cards show up as wrong card on SV+

Problems Fixed in Release 9.2.20

Following is the list of fixed problems in the 9.2.20 Switch Software release. Included with each is a brief description of the problem.

Bug ID

Description

 CSCdk33999


 "Connections automatically removed, SWERR 532 BAD_LCD_INDEX,SWERR 590 SEND_FAIL"


 CSCdk34492


 SNMP Agent - Wrong value returned for atmOtherEndptDesc


 CSCdk85811


 LAN fuse failed on NPM


 CSCdk89665


 Cannot configure line framing and signalling to NONE on UFM-C


 CSCdk93626


 Minimum MCR range is different in CLI & strata.mib


 CSCdm00711


 Hardware watchdog on NPM-32 when SNMP community strings configured


 CSCdm08324


 BXMs enables a BNIs CRXL statistic


 CSCdm27574


 Remove and reinsert Tx Fdr Trk cable causes connection failure.


 CSCdm27726


 CD errors: N. Fatal from 0x17: 0x25010022 0x0 0x22af 0x1 logged on BXM


 CSCdm32599


 NPM not recognizing traps with BXM ILMI at the cloud


 CSCdm41637


 Cnfpref buffer too short to load many 10 pref routes


 CSCdm43422


 Switch software does not dsptrkutl for NTM trunk


 CSCdm43783


 Swerr 55 occured after loadrev 9.2.1C in graceful upgrades


 CSCdm44536


 Swerr 532 & 55 cause by dcdrtbl on BXM & BNI trunks


 CSCdm50232


 Swerr 2000 logged on the node when trunk parameter is displayed through CiscoView


 CSCdm50251


 BPX: Port Real-Time Counters show incorrect values


 CSCdm50372


 Axis shelves report LMI failure when do hitless rebuild.


 CSCdm51357


 Swerr 121 on l3a(IGX)


 CSCdm52990


 Node experiences repeated abort 3M and 1M3 due to flooding on LMI channel


 CSCdm53035


 "Non-added trunks, the queue depth value should be changed with the line rate."


 CSCdm53119


 Swerr 129 is logged when dspswlog s command is executed on BPX node p6b


 CSCdm53126


 User ID updates do not stop if all nodes have invalid password for a user


 CSCdm53376


 Statistical trunk errors are not reported under dsptrkerrs


 CSCdm54117


 Swerr 9082s were logged at IST node igxr5


 CSCdm56012


 New versions of enhanced BXM card types need to be sent to SV.


 CSCdm57535


 Atmportstatmap_Table not getting initialized for ATM_PORT_STAT_BCM_RX_OFFSET


 CSCdm58398


 The trunk speed shown for dsptrkstats is incorrect


 CSCdm59091


 LDM & CVM conns cannot be modified by SV+ after upgrade


 CSCdm59267


 Additional ATM con subtypes need to be sent to SV+


 CSCdm59268


 Transaction handler sometimes is very busy on IGX


 CSCdm61126


 BPX reports incorrect status when burning firmware failed


 CSCdm62548


 Swerr 2085 occurs during a regression test.


 CSCdm63487


 Cnftrk does not prompt for Header Type: field


 CSCdm63889


 BCC reseated and remained in an update stage after BXMMEA upgrade


 CSCdm64045


 Software errors 886 and 2071 on image upgrade


 CSCdm65060


 Could not build a UNI IMA Group between IMATM and IGX UXM


 CSCdm65089


 Continuous PRI Clock loss messages in LOG


 CSCdm65104


 HDM failed the testcon command if its back card is configured as DTE


 CSCdm66452


 Tstber in manual mode stops receiving after nearly 1 1/2 hours.


 CSCdm67094


 Cnfasm is very detached from ASM functionality


 CSCdm67130


 ABR class of service is delayed from trunks


 CSCdm67358


 502/589/504/3m/1m3 and standby continuously WDTs


 CSCdm68678


 IMA virtual trunk configuration display will log swer 633 (LN_CNFG_DSP_OVFLW)


 CSCdm69180


 Cnftrk on UXM fdr trunk should be blocked if new LCNs are < used lcns


 CSCdm69421


 Traffic type displayed on cnftrk is not cleaned up correctly.


 CSCdm69834


 Default service template while upgrading from 9.1x to 9.2x


 CSCdm72193


 Unable to add UXM trunk

Problems Fixed in Release 9.2.10

Following is the list of fixed problems in the 9.2.10 Switch Software release. Included with each is a brief description of the problem.

Bug ID

Description

 CSCdk21358


 Front cards do not refresh if back cards are removed.


 CSCdk26240


 AIS transitions are not counted


 CSCdk29716


 Three-way PVC on frame relay connections after switchover


 CSCdk33721


 Swerr 614 is logged while doing a graceful upgrade


 CSCdk51121


 Dsplnalmcnf does not include trunks alarm configuration


 CSCdk51259


 slotBackNumPort is valid only for UXM and BXM cards


 CSCdk55034


 E3 BIP8 alarm error threshold is not triggered at 10E-3


 CSCdk65743


 Watchdog in VT_1 task (split off from CSCdk63204)


 CSCdk69040


 Adding cons to full port gives wrong return message


 CSCdk77005


 IGX16 logged 1000003 w/ SNMP process


 CSCdk87933


 "During SAR flood testing, some connections were autodelete"


 CSCdm02272


 BPX went into DEGRADED mode when cmd DSPLOGCD was initiated


 CSCdm04372


 Wrong atmPortIfType is returned for BXM-T3 card


 CSCdm04812


 Dspstatsinfo is counting feeder connections


 CSCdm14446


 No continuity for 3-byte frames routed over a UXM trunk


 CSCdm18555


 Need to redesign RCMP mismatch algorithm to allow use upgrade/downgrade card.


 CSCdm19544


 BPX 9.2 dspchstats does not show RX AIS


 CSCdm24031


 Burning old BXM FW to enhanced card will kill the card.


 CSCdm29600


 "After non graceful upgrade, swerrs 374, 752, Abort 1000003, can not add conns."


 CSCdm36631


 T3 trunk modification generates APS(OC3) traps


 CSCdm37694


 RtOp ran before ch clean up after 9.1.09 - 9.2.ja gracefully upgraded on UX


 CSCdm37802


 Swerr 706 in IGX feeder


 CSCdm39210


 Cnfcdaps causes a discrepancy between card attribute table and LCCB


 CSCdm39227


 CAC does not function correctly on a UXM port


 CSCdm39836


 Mib lacks definition for 8 port BNC connector card uaie1


 CSCdm39871


 MIB variable slotCardBackRev returns EW while it shows in CLI for ARM.


 CSCdm40006


 Add UXM/BXM VT to dspblkdfuncs and block in mixed NW


 CSCdm40707


 Swerr 4229 occurred after switchcc on BPX node


 CSCdm41274


 "Delyred logged swerr 514, 589, 143"


 CSCdm41406


 CPU usage above threshold message when do switchcc on 12000 conn node.


 CSCdm41415


 Dsptrkcnf/cnftrk does not show maximum channels for BNI trunks


 CSCdm41881


 "Swerr 514,589,502 logged on STBY BCC in l5b"


 CSCdm42754


 "Abort 2M when redundant CC, TFTP stats enabled, and a hitless is done"


 CSCdm43471


 SV+ can not see switch software 9.1.09 IGX-IGX FR Conns


 CSCdm44056


 APS Annex B switch software modifications


 CSCdm44387


 Swerr 1433 reported after switchcc


 CSCdm44587


 Swerr 29 BAD_PORT_NUM is reported on BPX node


 CSCdm44973


 Cnflnalm display shows alarm information on the wrong line of screen (after modifying)


 CSCdm45274


 Unable to configure Max LCNS to 32K on BXM-622-2DX card.


 CSCdm45592


 2068s and 504s flood log if statistics enabled before and after a hitless rebuild.


 CSCdm45812


 Block APS switching from standby to active line.


 CSCdm45889


 Swerrs 509 & 101 in IST n/w


 CSCdm46095


 Swerror 526 on adding or deleting APS lines


 CSCdm46601


 Software error 116 (BAD_OBJ_RESP) on statistic queries


 CSCdm46790


 "Memory leak in TRNS, SWERR 501, ABORT 3M, adaptive voice BW update msg leak."


 CSCdm47814


 Software error 9000 happens when UXM is activated in middle of its self-test


 CSCdm48694


 Robust card object message does not give Y redundancy information


 CSCdm49385


 Continuous hitless rebuild in case of abort


 CSCdm49988


 BXM card mismatch after upgrading from 9.109 to 9.2.01


 CSCdm51212


 3M Abort on BPX91 in IST n/w


 CSCdm54599


 UXM-FRM conns do not have continuity after a graceful upgrade (9.1.11->9.2.1K)


 CSCdm54814


 "549, 886 and 2071 occur on a rebuild, 928 on upping line"

Problems Fixed in Release 9.2.01

Following is the list of fixed problems in the 9.2.01 Switch Software release. Included with each is a brief description of the problem.

Bug ID

Description

 CSCdj15839


 False power supply over voltage or under voltage alarms reported


 CSCdj31366


 Clrcnf command to have explicit double warning message.


 CSCdk21503


 Swerr 921 on node n1a in 9.1 SLT n/w


 CSCdk28204


 Swerr 526 happened after switchcc on sw79


 CSCdk29850


 protocol_type column in frp table returns wrong number for IPX switch problem.


 CSCdk32046


 Cnfclnsigparm option 9 should not apply to FRM/FRP/UFM-C lines


 CSCdk40766


 Multiple upgrade/downgrade messages sent by switch software cause modem upgrade failure.


 CSCdk47079


 SW ERR 1000003 while running dth


 CSCdk52672


 Added PVCs after switchcc is auto-deleted.


 CSCdk56688


 Hipri error message problem


 CSCdk69440


 IGX running swsw 9.1.04 has dspprf IDLE at 30% when adding UVM cards


 CSCdk69498


 Incorrect A-bit status in FR NNI link


 CSCdk72199


 IMA trunk load db not updating after trunk failure


 CSCdk74438


 Addcon does not work with job (job does not take 8/8 options)


 CSCdk82927


 Slow TCP / Telnet response & disconnects on LAN pt after upgrade to NPM64


 CSCdk83511


 Correlation tag not checked at BPX Port


 CSCdk87005


 Avoid satellite *s needs extra parameters with an addcon


 CSCdk91395


 Vague error message when attempting to reconfigure remote PCR > T1/E1 port speed


 CSCdk92892


 The FTMs bandwidth is not configured when a FAX session is complete


 CSCdm05373


 Incorrect UVM channel configuration used


 CSCdm07825


 2065 caused when enabling invalid statistics configuration (fix is known)


 CSCdm10020


 Shelf alarm is unreachable on BPX (9.1) with IGX feeder graceful upgrade 9.1.08-9.


 CSCdm13012


 Can upped 31 vtrk and 1 port on a BXM. Card reported missing after down


 CSCdm15043


 Dangling LCNs might happen under some conditions.


 CSCdm16904


 "SWSW repeatedly reprograms same connections, nonstop in a loop, on UXM"


 CSCdm17109


 Software error 526 (NEG_FILL_REQ) occurred on IGX node


 CSCdm20480


 Card shows standby while cons are in the card


 CSCdm20716


 "Switchcc causes swerr 331 if on1 16, some reroutes if any VPC cons"


 CSCdm22316


 VSI feeder endpoint connections traffic are not mapping the vpi/vci correctly.


 CSCdm23206


 Cnfcon faces problem in accepting TCRR value through command line.


 CSCdm23489


 Swerr 514 is logged on bpx01 in upgrades testing


 CSCdm23669


 "921s filled software error log, appears to be related to a trunk deletion."


 CSCdm24282


 LM3 caused by cnfch command


 CSCdm25268


 LMI is still in loop on bpx/axis after upgrade


 CSCdm25595


 Dspcons shows PVCs but dspcon does not on BPX


 CSCdm26897


 Free the memory for IP relay message.


 CSCdm27681


 Y-red UXM/IMA back cards came up as mismatch after a graceful upgrade 9.1.09-9.2.0N


 CSCdm28561


 "4225,614,534,612, 4208, 3058 logged on switchover, stolen log end is root cause."


 CSCdm28721


 Swerr 532 in l5b


 CSCdm29043


 Potential for card errors with add_cd_red_cons() function.


 CSCdm29706


 Ports cannot configure HCF shift on/off w/out deleting connections


 CSCdm30018


 Trunk Cell routing restriction is not prompted any more for ATM conn.


 CSCdm30262


 Incorrect logic for VTs in g_ima_grp_member()


 CSCdm30359


 Failed to add daxcon path connection due to incorrect VPI checking.


 CSCdm30608


 Software error 55 after addalmslot 16


 CSCdm31674


 Yellow alarm line conditioning for T1 lines


 CSCdm32384


 Node rebuild on BPX caused comm fail.


 CSCdm33967


 After upgrade 9.1.09 to 9.2.00 trunks went comm. failure and then OK


 CSCdm34282


 Dbs_Pre_9110 not initialized properly in Root()

Additional Deliverables

SNMP MIB

The SNMP IGX/BPX switch SNMP MIB is being provided with the delivery of Release 9.2.33 Switch Software. The MIB is in standard ASN.1 format and is located in the ASCII text files agent.m, ilmi.m, ilmi_ctl.m, ilmiaddr.m, switch.m, swtraps.m, and errors.m which are included in the same directory as the Switch Software images. These files may be compiled with most standards-based MIB compilers.

Switch MIB changes of Release 9.2

The following Switch MIB changes were introduced since Release 9.2.00. The changes include Obsolete objects, Modified objects, and New objects:

switchIfTable

New objects:

		switchIfCtrlVPI
		switchIfCtrlVCIStart

Modified objects:

		switchIfEntry
switchIfScTmpltId
atmPortTable:

New objects:

		atmPortHcfShift

Modified objects:

		atmPortEntry
		atmPortMetro
atmPortQueueTable:

Modified objects:

		atmPortQueueType
atmPortQueueDepth
connTable:

Modified objects:

		connCurrRouteDesc
		connPrefRouteDesc
atmEndptTable:

Modified objects:

		atmEndptDesc
		atmOtherEndptDesc
		atmEndptSubType
		atmEndptMCR
atmBwClassTable:

Modified objects:

		atmBwClassConType

The following objects are associated with the switchShelf configuration branch.

New objects:
		shelfCnfgFBTC
		shelfCnfgSerialLeadTypeIndex
		shelfCnfgSerialLeadMonitorTimer
		shelfCnfgSystemTime
shelfSlotInfoTable:

Modified objects:

		slotBackType
		slotFrontNumPort
		slotBackSonetMode
slotCardMinBusUBU
sonetIfTable:

Modified objects:

		sonetIfType
sonetStatsTable:

New objects:

		sonetStatsYelTcs
		sonetStatsAisTcs
		sonetStatsLocs
		sonetStatsLops
		sonetStatsPthAis
		sonetStatsPthYels
		sonetStatsSecBip8s
		sonetStatsLnBip24s
		sonetStatsLnFebes
		sonetStatsPthBip8s
		sonetStatsPthFebes
		sonetStatsSecBip8Es
		sonetStatsLnBip24Es
		sonetStatsLnFebeEs
		sonetStatsPthBip8Es
		sonetStatsPthFebeEs
		sonetStatsSecBip8Ses
		sonetStatsSecSefs
		sonetStatsLnBip24Ses
		sonetStatsLnFebeSes
		sonetStatsPthBip8Ses
		sonetStatsPthFebeSes
		sonetStatsLnUas
		sonetStatsLnFarendUas
		sonetStatsPthUas
		sonetStatsPthFarendUas
		sonetStatsHcsCrtblErrEs

Modified objects:

sonetStatsEntry
atmTrunks table:

Modified objects:

		atmTrkType
		atmTrkTrafCls
rsrcPartiTable:

New objects:

		rsrcPartiVsiIlmiEnable

Modified objects:

		rsrcPartiEntry
		rsrcPartiVsiVpiEnd
serialPortTable:

New objects:

		serialPortLeadState

Modified objects:

		SerialPortEntry
serialPortLeadState

Default Values

BPX 8600 Nodes

The default values for BXM and Enhanced-BXM cards are the same.

hugo           TN    StrataCom       BPX 8620  9.2.34    Date/Time Not Set      
                                                                                
                           System-Wide Parameters                               
                                                                                
1  Max Time Stamped Packet Age (msec) ................................   32     
2  Allow CPU Starvation of Fail Handler ..............................   No     
3  Max Network Delay for 'v' connections (msec).......................   14     
4  Max Network Delay for 'c' connections (msec).......................   27     
5  Max Network Delay for 't' & 'p' connections (msec).................   14     
6  Max Network Delay for 'a' connections (msec).......................   27     
7  Max Network Delay for High Speed Data connections (msec)...........   32     
8  Max Network Delay for CDP-CDP 'v' connections (msec)...............   64     
9  Max Network Delay for CDP-CDP 'c' connections (msec)...............   64     
10 Max Network Delay for CDP-CDP 't' & 'p' connections (msec).........   64     
11 Max Network Delay for CDP-CDP 'a' connections (msec)...............   64     
12 Max Network Delay for CDP-CDP High Speed Data connections (msec)...   64     
13 Enable Discard Eligibility.........................................   No     
14 Use Frame Relay Standard Parameters Bc and Be......................   No     
15 Max Local Delay for Interdom CDP-CDP 'v' conns (msec)..............   27     
16 Max Local Delay for Interdom CDP-CDP 'c' conns (msec)..............   27     
17 Max Local Delay for Interdom CDP-CDP 't' & 'p' conns (msec)........   27     
18 Max Local Delay for Interdom CDP-CDP 'a' conns (msec)..............   27     
19 Max Local Delay for Interdom CDP-CDP High Speed Data conns (msec)..   27     
20 Max Local Delay for Interdom High Speed Data conns (msec)..........   28     
21 FastPAD Jitter Buffer Size  (msec).................................   15     
22 Number of Consecutive Invalid Login Attempts to Cause Major Alarm .    0     
23 Enable Connection Deroute Delay feature............................   No     
24 Interval Statistics polling rate for ATM VCs.......................    5     
25 Interval Statistics polling rate for ports on IPX/IGX 8400 nodes...    5     
                                                                                
This Command: cnfsysparm                                                        
                                                                                
1  Update Initial Delay   [ 5000] (D)   16 Stats Memory (x 100KB) [  132] (D)   
2  Update Per-Node Delay  [30000] (D)   17 Standby Update Timer   [   10] (D)   
3  Comm-Break Test Delay  [30000] (D)   18 Stby Updts Per Pass    [   50] (D)   
4  Comm-Break Test Offset [   10] (D)   19 Gateway ID Timer       [   30] (D)   
5  Network Timeout Period [ 1700] (D)   20 GLCON Alloc Timer      [   30] (D)   
6  Network Inter-p Period [ 4000] (D)   21 Comm Fail Delay        [   60] (D)   
7  NW Sliding Window Size [    1] (D)   22 Nw Hdlr Timer (msec)   [   50] (D)   
8  Num Normal Timeouts    [    7] (D)   23 SAR CC Transmit Rate   [  560] (D)   
9  Num Inter-p Timeouts   [    3] (D)   24 SAR High Transmit Rate [  280] (D)   
10 Num Satellite Timeouts [    6] (D)   25 SAR Low Transmit Rate  [   56] (D)   
11 Num Blind Timeouts     [    4] (D)   26 SAR VRAM Cngestn Limit [ 7680] (D)   
12 Num CB Msg Timeouts    [    5] (D)   27 SAR VRAM Cell Discard  [  256] (D)   
13 Comm Fail Interval     [10000] (D)   28 ASM Card Cnfged        [    Y] (Y/N) 
14 Comm Fail Multiplier   [    3] (D)   29 TFTP Grant Delay (sec) [    1] (D)   
15 CC Redundancy Cnfged   [    Y] (Y/N) 30 TFTP ACK Timeout (sec) [   10] (D)   
                                                                                
31 TFTP Write Retries     [    3] (D)   46 Max Htls Rebuild Count [  100] (D)   
32 SNMP Event logging     [    Y] (Y/N) 47 Htls Counter Reset Time[ 1000] (D)   
33 Job Lock Timeout       [   60] (D)   48 Send Abit early        [    N] (Y/N) 
34 Max Via LCONs          [50000] (D)   49 Abit Tmr Multiplier  M [    0] (D)   
35 Max Blind Segment Size [ 3570] (D)   50 Abit Tmr Granularity N [    3] (D)   
36 Max XmtMemBlks per NIB [ 3000] (D)   51 FBTC with PPDPolicing  [    N] (Y/N) 
37 Max Mem on Stby Q (%)  [   33] (D)                                           
38 Stat Config Proc Cnt   [ 1000] (D)                                           
39 Stat Config Proc Delay [ 2000] (D)                                           
40 Enable Degraded Mode   [    Y] (Y/N)                                         
41 Trk Cell Rtng Restrict [    Y] (Y/N)                                         
42 Enable Feeder Alert    [    N] (Y/N)                                         
43 Reroute on Comm Fail   [    N] (Y/N)                                         
44 Auto Switch on Degrade [    Y] (Y/N)                                         
45 Max Degraded Aborts    [  100] (D)                                           
                                                                                
This Command: cnfnodeparm                                                       
                                                                                
hugo           TN    StrataCom       BPX 8620  9.2.34    Date/Time Not Set      
                                                                                
Index Status    Function                                                        
                                                                                
1     Enabled   Automatic TRK Loopback Test on Local/Remote Alarms              
2     Enabled   User Command Logging                                            
3     Enabled   Automatic Card Reset on Hardware Error                          
4     Enabled   Card Error Record Wraparound                                    
5     Disabled  Card Test After Failure                                         
6     Disabled  Download From Remote Cisco StrataView Plus                      
7     Disabled  Logging of conn events in local event log                       
8     Disabled  Logging of conn events in Cisco StrataView Plus  event log      
9     Disabled  Force Download From a Specific IP address                       
                                                                                
This Command: cnffunc                                                           
                                                                                
hugo           TN    StrataCom       BPX 8620  9.2.34    Date/Time Not Set      
                                                                                
Index Status    Function                                                        
                                                                                
1     Disabled  Configuration Save/Restore                                      
2     Enabled   ForeSight                                                       
3     Disabled  Multiple VTs (1 session enabled)                                
4     Disabled  Virtual Trunks                                                  
5     Enabled   ABR standard with VSVD                                          
                                                                                
This Command: cnfswfunc                                                         
                                                                                
hugo           TN    StrataCom       BPX 8620  9.2.34    Date/Time Not Set      
                                                                                
Card    Test   - - - - - - Self Test - - - - - - -   - - Background Test - - -  
Type    Freq   Enable        Inc   Thresh  Timeout   Enable        Inc   Thresh 
----    -----  --------  -------  -------  -------   --------  -------  ------- 
BCC      1600  Enabled       100      300      800   N/A           100      300 
ASM       300  Disabled      100      300       60   N/A           100      300 
BNI-T3    300  Enabled       100      300      150   N/A           100      300 
BNI-E3    300  Enabled       100      300      150   N/A           100      300 
ASI-E3    900  Enabled       100      300      800   Enabled       100      300 
ASI-T3    900  Enabled       100      300      800   Enabled       100      300 
ASI-155   900  Enabled       100      300      800   Enabled       100      300 
BNI-155   300  Enabled       100      300      150   N/A           100      300 
BXM      4000  Enabled       100      300     3000   Enabled       100      300 
                                                                                
This Command: cnftstparm                                                        
                                                                                
hugo           TN    StrataCom       BPX 8620  9.2.34    Date/Time Not Set      
                                                                                
1  Normalization Interval    [    2] (D)                                        
2  Max Number To Normalize   [    5] (D)                                        
3  Normalization Logging     [   No]                                            
4  Settling Interval         [    4] (D)                                        
5  Minimum Open Space        [ 1000] (D)                                        
6  Normalization Priority    [ Load]                                            
7  Load Sample Period        [    4] (D)                                        
8  Maximum Routing Bundle    [   90] (D)                                        
9  Reroute Timer             [    0] (secs)                                     
10 Reset Timer on Line Fail  [  Yes]                                            
11 Max Down/Up Per Pass      [   50] (D)                                        
12 Down/Up Timer             [30000] (msecs)                                    
13 Max Route Errs per cycle  [   50] (D)                                        
14 Time between Rrt cycles   [    5] (mins)                                     
15 Max. Rrt Err cycles       [   10] (D)                                        
16 Routing pause timer       [    0] (msecs)                                    
17 Max msgs sent per update  [   10] (D)                                        
18 Send SVC urgent msg       [   No]                                            
19 Max SVC Retry             [    0] (D)                                        
20 Wait for TBL Updates      [   70] (100 msecs)                                
21 Max Derouting Bndl (0=all)[  500] (D)                                        
22 Enable Cost-Based Routing [   No]                                            
23 Enable Route Cache Usage  [   No]                                            
24 Use Delay for Routing     [   No]                                            
25 # of reroute groups used  [   50] (D)                                        
26 Starting size of RR grps  [    0] (CLU)                                      
27 Increment between RR grps [  100] (CLU)                                      
                                                                                
This Command: cnfcmparm                                                         
                                                                                
hugo           TN    StrataCom       BPX 8620  9.2.34    Date/Time Not Set      
                                                                                
1  Rmt Blk Freq (msec)     [    100]    16 FW Dnld Msgs/Block(dec) [      4]    
2  Rmt Blk Size (hex)      [    400]    17 Flash Write TO(msec)    [  16000]    
3  Lcl Blk Freq (msec)     [    100]    18 Flash Erase TO(msec)    [    100]    
4  Lcl Blk Size (hex)      [    400]    19 Erase Verify TO(msec)   [  16000]    
5  Image Req Freq (msec)   [  10000]    20 Standby Flash TO(sec)   [    300]    
6  Dnld Req Freq (msec)    [  10000]    21 Lcl Flash Init TO(msec) [   1000]    
7  Session Timeout (msec)  [  30000]    22 Flsh Write Blk Sz (hex) [  10000]    
8  Request Hop Limit (dec) [      1]    23 Flsh Verfy Blk Sz (hex) [    400]    
9  Crc Throttle Freq (dec) [   5000]    24 Chips Per Write/Erase   [      1]    
10 Crc Block Size (hex)    [    400]                                            
11 Rev Change Wait(dec)    [      0]                                            
12 CCs Switch Wait(dec)    [   1000]                                            
13 Lcl Response TO(msec)   [   5000]                                            
14 Rmt Response TO(msec)   [  20000]                                            
15 FW Dnld Block TO(msec)  [     50]                                            
                                                                                
This Command: cnfdlparm                                                         
                                                                                
hugo           TN    StrataCom       BPX 8620  9.2.34    Date/Time Not Set      
                                                                                
1. Logout Time ........... 20 minutes                                           
2. VT Logout Time ........ 4 minutes                                            
3. Prompt Time ........... 60 seconds                                           
4. Command Time .......... 3 minutes                                            
5. UID Privilege Level ... 6                                                    
6. Input Character Echo .. Enabled                                              
7. Screen Update Time .... 10 seconds                                           
                                                                                
This Command: cnfuiparm                                                         
                                                                                
hugo           TN    StrataCom       BPX 8620  9.2.34    Date/Time Not Set      
                                                                                
Function            Number   Status      Function            Number   Status    
Background Upcard     1      Enabled     Conn Stat Sampling    15     Enabled   
Background Updates    2      Disabled    Neighbor Update Errs  16     Disabled  
Standby Terminal      3      Enabled                                            
Memory Protection     4      Enabled                                            
Comm Break            5      Enabled                                            
Comm Fail Test        6      Enabled                                            
CRC Test              7      Enabled                                            
Bus Fail Detection    8      Enabled                                            
Line Diag             9      Enabled                                            
Clock Restoral        10     Enabled                                            
Cm_Rerouting          11     Enabled                                            
Clock Routing         12     Enabled                                            
Dynamic BW Allocation 13     Enabled                                            
Modem Polling         14     Enabled                                            
                                                                                
This Command: on1                                                               
                                                                                
hugo           TN    StrataCom       BPX 8620  9.2.34    Date/Time Not Set      
                                                                                
Function            Number   Status      Function            Number   Status    
Line Stat Sampling    1      Enabled     Robust Alarm Updates  15     Enabled   
Statistical Alarm     2      Enabled     Realtime Counters     16     Enabled   
Job Ready Checker     3      Enabled     LAN Interface         17     Enabled   
Configuration Backup  4      Enabled     Update Standby Stats  18     Enabled   
Standby Update        5      Enabled     Telnet Access         19     Enabled   
Downloader            6      Enabled     Junction ID           20     Enabled   
Cm Updates            7      Enabled     Mult SV+/Routing Node 21     Disabled  
Topo/Stat Updates     8      Enabled     Simulated Fdr Trks    22     Disabled  
Card Statistical Alms 9      Enabled     Deroute Delay         23     Enabled   
Card Stat Sampling    10     Enabled     Auto Renum Fail Recov 24     Enabled   
Address Validation    11     Enabled     Card Simulation Tool  25     Disabled  
ASM Stats Polling     12     Enabled                                            
Port Stat Sampling    13     Enabled                                            
Robust Updates        14     Enabled                                            
                                                                                
This Command: on2                                                               
                                                                                
hugo           TN    StrataCom       BPX 8620  9.2.34    Date/Time Not Set      
                                                                                
Function            Number   Status                                             
Region memory init    1      Disabled                                           
Trace Msg Sent        2      Disabled                                           
Multi-DB Stby Updates 3      Enabled                                            
Trace Conv Msg        4      Disabled                                           
                                                                                
This Command: on3

BNI-T3

hugo           TN    StrataCom       BPX 8620  9.2.34    Date/Time Not Set      
                                                                                
TRK  2.1 Config     T3      [96000 cps]    BNI-T3 slot:  2                      
Transmit Rate:         96000               VPC Conns disabled:    --            
Protocol By The Card:  --                  Line framing:          PLCP          
VC Shaping:            --                       coding:           --            
Hdr Type NNI:          --                       recv impedance:   --            
Statistical Reserve:   1000    cps              cable type:                     
Idle code:             7F hex                         length:     0-225 ft.     
Connection Channels:   1771                Pass sync:             No            
Traffic:V,TS,NTS,FR,FST,CBR,N&RT-VBR,ABR   Loop clock:            No            
SVC Vpi Min:           --                  HCS Masking:           Yes           
SVC Channels:          0                   Payload Scramble:      No            
SVC Bandwidth:         0      cps          Frame Scramble:        --            
Restrict CC traffic:   No                  Virtual Trunk Type:    --            
Link type:             Terrestrial         Virtual Trunk VPI:     --            
Routing Cost:          10                  Deroute delay time:    0 seconds     
                                                                                
Last Command: dsptrkcnf 2.1                                                     
                                                                                
hugo           TN    StrataCom       BPX 8620  9.2.34    Date/Time Not Set      
                                                                                
TRK 2.1 Parameters                                                              
 1 Q Depth - rt-VBR    [  242] (Dec)    15 Q Depth   - CBR     [  600] (Dec)    
 2 Q Depth - Non-TS    [  360] (Dec)    16 Q Depth   - nrt-VBR [ 1000] (Dec)    
 3 Q Depth - TS        [ 1000] (Dec)    17 Q Depth   - ABR     [ 8878] (Dec)    
 4 Q Depth - BData A   [ 1000] (Dec)    18 Low  CLP  - CBR     [ 100] (%)       
 5 Q Depth - BData B   [ 8000] (Dec)    19 High CLP  - CBR     [ 100] (%)       
 6 Q Depth - High Pri  [ 1000] (Dec)    20 Low  CLP  - nrt-VBR [ 100] (%)       
 7 Max Age - rt-VBR    [   20] (Dec)    21 High CLP  - nrt-VBR [ 100] (%)       
 8 Red Alm - I/O (Dec) [  2500 /  15000]22 Low CLP/EPD-ABR     [  60] (%)       
 9 Yel Alm - I/O (Dec) [  2500 /  15000]23 High CLP  - ABR     [  80] (%)       
10 Low  CLP - BData A  [ 100] (%)       24 EFCN      - ABR     [  30] (%)       
11 High CLP - BData A  [ 100] (%)       25 SVC Queue Pool Size [    0] (Dec)    
12 Low  CLP - BData B  [  25] (%)                                               
13 High CLP - BData B  [  75] (%)                                               
14 EFCN     - BData B  [  30] (Dec)                                             
                                                                                
This Command: cnftrkparm 2.1

BNI-E3

hugo           TN    StrataCom       BPX 8620  9.2.34    Date/Time Not Set      
                                                                                
TRK  3.1 Config     E3     [80000 cps]     BNI-E3 slot:  3                      
Transmit Rate:         80000               VPC Conns disabled:    --            
Protocol By The Card:  --                  Line framing:          --            
VC Shaping:            --                       coding:           --            
Hdr Type NNI:          --                       recv impedance:   --            
Statistical Reserve:   1000    cps              cable type:                     
Idle code:             7F hex                         length:     0-225 ft.     
Connection Channels:   1771                Pass sync:             No            
Traffic:V,TS,NTS,FR,FST,CBR,N&RT-VBR,ABR   Loop clock:            No            
SVC Vpi Min:           --                  HCS Masking:           Yes           
SVC Channels:          0                   Payload Scramble:      Yes           
SVC Bandwidth:         0      cps          Frame Scramble:        --            
Restrict CC traffic:   No                  Virtual Trunk Type:    --            
Link type:             Terrestrial         Virtual Trunk VPI:     --            
Routing Cost:          10                  Deroute delay time:    0 seconds     
                                                                                
Last Command: dsptrkcnf 3.1                                                     
                                                                                
hugo           TN    StrataCom       BPX 8620  9.2.34    Date/Time Not Set      
                                                                                
TRK 3.1 Parameters                                                              
 1 Q Depth - rt-VBR    [  202] (Dec)    15 Q Depth   - CBR     [  600] (Dec)    
 2 Q Depth - Non-TS    [  300] (Dec)    16 Q Depth   - nrt-VBR [ 1000] (Dec)    
 3 Q Depth - TS        [ 1000] (Dec)    17 Q Depth   - ABR     [ 8978] (Dec)    
 4 Q Depth - BData A   [ 1000] (Dec)    18 Low  CLP  - CBR     [ 100] (%)       
 5 Q Depth - BData B   [ 8000] (Dec)    19 High CLP  - CBR     [ 100] (%)       
 6 Q Depth - High Pri  [ 1000] (Dec)    20 Low  CLP  - nrt-VBR [ 100] (%)       
 7 Max Age - rt-VBR    [   20] (Dec)    21 High CLP  - nrt-VBR [ 100] (%)       
 8 Red Alm - I/O (Dec) [  2500 /  15000]22 Low CLP/EPD-ABR     [  60] (%)       
 9 Yel Alm - I/O (Dec) [  2500 /  15000]23 High CLP  - ABR     [  80] (%)       
10 Low  CLP - BData A  [ 100] (%)       24 EFCN      - ABR     [  30] (%)       
11 High CLP - BData A  [ 100] (%)       25 SVC Queue Pool Size [    0] (Dec)    
12 Low  CLP - BData B  [  25] (%)                                               
13 High CLP - BData B  [  75] (%)                                               
14 EFCN     - BData B  [  30] (Dec)                                             
                                                                                
This Command: cnftrkparm 3.1

BNI-155/155E

hugo           TN    StrataCom       BPX 8620  9.2.34    Date/Time Not Set      
                                                                                
TRK  4.1 Config     OC3     [353207cps]    BNI-155 slot: 4                      
Transmit Rate:         353208              VPC Conns disabled:    --            
Protocol By The Card:  --                  Line framing:          STS-3C        
VC Shaping:            --                       coding:           --            
Hdr Type NNI:          --                       recv impedance:   --            
Statistical Reserve:   1000    cps              cable type:       --            
Idle code:             7F hex                         length:     --            
Connection Channels:   16050               Pass sync:             No            
Traffic:V,TS,NTS,FR,FST,CBR,N&RT-VBR,ABR   Loop clock:            No            
SVC Vpi Min:           --                  HCS Masking:           Yes           
SVC Channels:          0                   Payload Scramble:      Yes           
SVC Bandwidth:         0      cps          Frame Scramble:        Yes           
Restrict CC traffic:   No                  Virtual Trunk Type:    --            
Link type:             Terrestrial         Virtual Trunk VPI:     --            
Routing Cost:          10                  Deroute delay time:    0 seconds     
                                                                                
Last Command: dsptrkcnf 4.1                                                     
                                                                                
hugo           TN    StrataCom       BPX 8620  9.2.34    Date/Time Not Set      
                                                                                
TRK 4.1 Parameters                                                              
 1 Q Depth - rt-VBR    [  885] (Dec)    15 Q Depth   - CBR     [  600] (Dec)    
 2 Q Depth - Non-TS    [ 1324] (Dec)    16 Q Depth   - nrt-VBR [ 1000] (Dec)    
 3 Q Depth - TS        [ 1000] (Dec)    17 Q Depth   - ABR     [15463] (Dec)    
 4 Q Depth - BData A   [ 1000] (Dec)    18 Low  CLP  - CBR     [ 100] (%)       
 5 Q Depth - BData B   [ 8000] (Dec)    19 High CLP  - CBR     [ 100] (%)       
 6 Q Depth - High Pri  [ 1000] (Dec)    20 Low  CLP  - nrt-VBR [ 100] (%)       
 7 Max Age - rt-VBR    [   20] (Dec)    21 High CLP  - nrt-VBR [ 100] (%)       
 8 Red Alm - I/O (Dec) [  2500 /  10000]22 Low CLP/EPD-ABR     [  60] (%)       
 9 Yel Alm - I/O (Dec) [  2500 /  10000]23 High CLP  - ABR     [  80] (%)       
10 Low  CLP - BData A  [ 100] (%)       24 EFCN      - ABR     [  30] (%)       
11 High CLP - BData A  [ 100] (%)       25 SVC Queue Pool Size [    0] (Dec)    
12 Low  CLP - BData B  [  25] (%)                                               
13 High CLP - BData B  [  75] (%)                                               
14 EFCN     - BData B  [  30] (Dec)                                             
                                                                                
This Command: cnftrkparm 4.1

BXM-T3

hugo           TN    StrataCom       BPX 8620  9.2.34    Date/Time Not Set      
                                                                                
TRK  5.1 Config     T3     [96000 cps]     BXM slot:     5                      
Transmit Rate:         96000               VPC Conns disabled:    No            
Protocol By The Card:  No                  Line framing:          PLCP          
VC Shaping:            No                       coding:           --            
Hdr Type NNI:          Yes                      recv impedance:   --            
Statistical Reserve:   1000    cps              cable type:       --            
Idle code:             7F hex                         length:     0-225 ft.     
Connection Channels:   256                 Pass sync:             No            
Traffic:V,TS,NTS,FR,FST,CBR,N&RT-VBR,ABR   Loop clock:            No            
SVC Vpi Min:           0                   HCS Masking:           Yes           
SVC Channels:          0                   Payload Scramble:      No            
SVC Bandwidth:         0      cps          Frame Scramble:        --            
Restrict CC traffic:   No                  Virtual Trunk Type:    --            
Link type:             Terrestrial         Virtual Trunk VPI:     --            
Routing Cost:          10                  Deroute delay time:    0 seconds     
                                                                                
Last Command: dsptrkcnf 5.1                                                     
                                                                                
hugo           TN    StrataCom       BPX 8620  9.2.34    Date/Time Not Set      
                                                                                
TRK 5.1 Parameters                                                              
 1 Q Depth - rt-VBR    [  242] (Dec)    15 Q Depth   - CBR     [  400] (Dec)    
 2 Q Depth - Non-TS    [  360] (Dec)    16 Q Depth   - nrt-VBR [ 5000] (Dec)    
 3 Q Depth - TS        [ 1000] (Dec)    17 Q Depth   - ABR     [10000] (Dec)    
 4 Q Depth - BData A   [ 8000] (Dec)    18 Low  CLP  - CBR     [  60] (%)       
 5 Q Depth - BData B   [ 8000] (Dec)    19 High CLP  - CBR     [  80] (%)       
 6 Q Depth - High Pri  [ 1000] (Dec)    20 Low  CLP  - nrt-VBR [  60] (%)       
 7 Max Age - rt-VBR    [   20] (Dec)    21 High CLP  - nrt-VBR [  80] (%)       
 8 Red Alm - I/O (Dec) [  2500 /  15000]22 Low CLP/EPD-ABR     [  60] (%)       
 9 Yel Alm - I/O (Dec) [  2500 /  15000]23 High CLP  - ABR     [  80] (%)       
10 Low  CLP - BData A  [ 100] (%)       24 EFCN      - ABR     [  20] (%)       
11 High CLP - BData A  [ 100] (%)       25 SVC Queue Pool Size [    0] (Dec)    
12 Low  CLP - BData B  [  25] (%)                                               
13 High CLP - BData B  [  75] (%)                                               
14 EFCN     - BData B  [  30] (Dec)                                             
                                                                                
This Command: cnftrkparm 5.1

BXM-E3

hugo           TN    StrataCom       BPX 8620  9.2.34    Date/Time Not Set
 
TRK 13.1 Config     E3     [80000 cps]     BXM slot:     13
Transmit Rate:         80000               VPC Conns disabled:    No
Protocol By The Card:  No                  Line framing:          --
VC Shaping:            No                       coding:           --
Hdr Type NNI:          Yes                      recv impedance:   --
Statistical Reserve:   1000    cps              cable type:       --
Idle code:             7F hex                         length:     0-225 ft.
Connection Channels:   256                 Pass sync:             No
Traffic:V,TS,NTS,FR,FST,CBR,N&RT-VBR,ABR   Loop clock:            No
SVC Vpi Min:           0                   HCS Masking:           Yes
SVC Channels:          0                   Payload Scramble:      Yes
SVC Bandwidth:         0      cps          Frame Scramble:        --
Restrict CC traffic:   No                  Virtual Trunk Type:    --
Link type:             Terrestrial         Virtual Trunk VPI:     --
Routing Cost:          10                  Deroute delay time:    0 seconds
 
Last Command: dsptrkcnf 13.1
 
hugo           TN    StrataCom       BPX 8620  9.2.34    Date/Time Not Set
 
TRK 13.1 Parameters
 1 Q Depth - rt-VBR    [  202] (Dec)    15 Q Depth   - CBR     [  400] (Dec)
 2 Q Depth - Non-TS    [  300] (Dec)    16 Q Depth   - nrt-VBR [ 5000] (Dec)
 3 Q Depth - TS        [ 1000] (Dec)    17 Q Depth   - ABR     [10000] (Dec)
 4 Q Depth - BData A   [ 8000] (Dec)    18 Low  CLP  - CBR     [  60] (%)
 5 Q Depth - BData B   [ 8000] (Dec)    19 High CLP  - CBR     [  80] (%)
 6 Q Depth - High Pri  [ 1000] (Dec)    20 Low  CLP  - nrt-VBR [  60] (%)
 7 Max Age - rt-VBR    [   20] (Dec)    21 High CLP  - nrt-VBR [  80] (%)
 8 Red Alm - I/O (Dec) [  2500 /  15000]22 Low CLP/EPD-ABR     [  60] (%)
 9 Yel Alm - I/O (Dec) [  2500 /  15000]23 High CLP  - ABR     [  80] (%)
10 Low  CLP - BData A  [ 100] (%)       24 EFCN      - ABR     [  20] (%)
11 High CLP - BData A  [ 100] (%)       25 SVC Queue Pool Size [    0] (Dec)
12 Low  CLP - BData B  [  25] (%)
13 High CLP - BData B  [  75] (%)
14 EFCN     - BData B  [  30] (Dec)
 
This Command: cnftrkparm 13.1

BXM-OC3

hugo           TN    StrataCom       BPX 8620  9.2.34    Date/Time Not Set      
                                                                                
TRK  6.1 Config     OC3    [353207cps]     BXM slot:     6                      
Transmit Rate:         353208              VPC Conns disabled:    No            
Protocol By The Card:  No                  Line framing:          STS-3C        
VC Shaping:            No                       coding:           --            
Hdr Type NNI:          Yes                      recv impedance:   --            
Statistical Reserve:   1000    cps              cable type:       --            
Idle code:             7F hex                         length:     --            
Connection Channels:   256                 Pass sync:             No            
Traffic:V,TS,NTS,FR,FST,CBR,N&RT-VBR,ABR   Loop clock:            No            
SVC Vpi Min:           0                   HCS Masking:           Yes           
SVC Channels:          0                   Payload Scramble:      Yes           
SVC Bandwidth:         0      cps          Frame Scramble:        Yes           
Restrict CC traffic:   No                  Virtual Trunk Type:    --            
Link type:             Terrestrial         Virtual Trunk VPI:     --            
Routing Cost:          10                  Deroute delay time:    0 seconds     
                                                                                
Last Command: dsptrkcnf 6.1                                                     
                                                                                
hugo           TN    StrataCom       BPX 8620  9.2.34    Date/Time Not Set      
                                                                                
TRK 6.1 Parameters                                                              
 1 Q Depth - rt-VBR    [  885] (Dec)    15 Q Depth   - CBR     [  600] (Dec)    
 2 Q Depth - Non-TS    [ 1324] (Dec)    16 Q Depth   - nrt-VBR [ 5000] (Dec)    
 3 Q Depth - TS        [ 1000] (Dec)    17 Q Depth   - ABR     [20000] (Dec)    
 4 Q Depth - BData A   [10000] (Dec)    18 Low  CLP  - CBR     [  60] (%)       
 5 Q Depth - BData B   [10000] (Dec)    19 High CLP  - CBR     [  80] (%)       
 6 Q Depth - High Pri  [ 1000] (Dec)    20 Low  CLP  - nrt-VBR [  60] (%)       
 7 Max Age - rt-VBR    [   20] (Dec)    21 High CLP  - nrt-VBR [  80] (%)       
 8 Red Alm - I/O (Dec) [  2500 /  10000]22 Low CLP/EPD-ABR     [  60] (%)       
 9 Yel Alm - I/O (Dec) [  2500 /  10000]23 High CLP  - ABR     [  80] (%)       
10 Low  CLP - BData A  [ 100] (%)       24 EFCN      - ABR     [  20] (%)       
11 High CLP - BData A  [ 100] (%)       25 SVC Queue Pool Size [    0] (Dec)    
12 Low  CLP - BData B  [  25] (%)                                               
13 High CLP - BData B  [  75] (%)                                               
14 EFCN     - BData B  [  30] (Dec)                                             
                                                                                
This Command: cnftrkparm 6.1

BXM-OC12

hugo           TN    StrataCom       BPX 8620  9.2.34    Date/Time Not Set      
                                                                                
TRK  9.1 Config     OC12   [1412679cps]    BXM slot:     9                      
Transmit Rate:         1412830             VPC Conns disabled:    No            
Protocol By The Card:  No                  Line framing:          STS-12C       
VC Shaping:            No                       coding:           --            
Hdr Type NNI:          Yes                      recv impedance:   --            
Statistical Reserve:   1000    cps              cable type:       --            
Idle code:             7F hex                         length:     --            
Connection Channels:   256                 Pass sync:             No            
Traffic:V,TS,NTS,FR,FST,CBR,N&RT-VBR,ABR   Loop clock:            No            
SVC Vpi Min:           0                   HCS Masking:           Yes           
SVC Channels:          0                   Payload Scramble:      Yes           
SVC Bandwidth:         0      cps          Frame Scramble:        Yes           
Restrict CC traffic:   No                  Virtual Trunk Type:    --            
Link type:             Terrestrial         Virtual Trunk VPI:     --            
Routing Cost:          10                  Deroute delay time:    0 seconds     
                                                                                
Last Command: dsptrkcnf 9.1                                                     
                                                                                
hugo           TN    StrataCom       BPX 8620  9.2.34    Date/Time Not Set      
                                                                                
TRK 9.1 Parameters                                                              
 1 Q Depth - rt-VBR    [ 3533] (Dec)    15 Q Depth   - CBR     [ 1200] (Dec)    
 2 Q Depth - Non-TS    [ 5297] (Dec)    16 Q Depth   - nrt-VBR [10000] (Dec)    
 3 Q Depth - TS        [ 1000] (Dec)    17 Q Depth   - ABR     [40000] (Dec)    
 4 Q Depth - BData A   [40000] (Dec)    18 Low  CLP  - CBR     [  60] (%)       
 5 Q Depth - BData B   [40000] (Dec)    19 High CLP  - CBR     [  80] (%)       
 6 Q Depth - High Pri  [ 1000] (Dec)    20 Low  CLP  - nrt-VBR [  60] (%)       
 7 Max Age - rt-VBR    [   20] (Dec)    21 High CLP  - nrt-VBR [  80] (%)       
 8 Red Alm - I/O (Dec) [  2500 /  10000]22 Low CLP/EPD-ABR     [  60] (%)       
 9 Yel Alm - I/O (Dec) [  2500 /  10000]23 High CLP  - ABR     [  80] (%)       
10 Low  CLP - BData A  [ 100] (%)       24 EFCN      - ABR     [  20] (%)       
11 High CLP - BData A  [ 100] (%)       25 SVC Queue Pool Size [    0] (Dec)    
12 Low  CLP - BData B  [  25] (%)                                               
13 High CLP - BData B  [  75] (%)                                               
14 EFCN     - BData B  [  30] (Dec)                                             
                                                                                
This Command: cnftrkparm 9.1

IGX 8400 Nodes

mulder         TN    StrataCom       IGX 8420  9.2.34    Date/Time Not Set      
                                                                                
                           System-Wide Parameters                               
                                                                                
1  Max Time Stamped Packet Age (msec) ................................   32     
2  Allow CPU Starvation of Fail Handler ..............................   No     
3  Max Network Delay for 'v' connections (msec).......................   14     
4  Max Network Delay for 'c' connections (msec).......................   27     
5  Max Network Delay for 't' & 'p' connections (msec).................   14     
6  Max Network Delay for 'a' connections (msec).......................   27     
7  Max Network Delay for High Speed Data connections (msec)...........   32     
8  Max Network Delay for CDP-CDP 'v' connections (msec)...............   64     
9  Max Network Delay for CDP-CDP 'c' connections (msec)...............   64     
10 Max Network Delay for CDP-CDP 't' & 'p' connections (msec).........   64     
11 Max Network Delay for CDP-CDP 'a' connections (msec)..............    64     
12 Max Network Delay for CDP-CDP High Speed Data connections (msec)...   64     
13 Enable Discard Eligibility.........................................   No     
14 Use Frame Relay Standard Parameters Bc and Be......................   No     
15 Max Local Delay for Interdom CDP-CDP 'v' conns (msec)..............   27     
16 Max Local Delay for Interdom CDP-CDP 'c' conns (msec)..............   27     
17 Max Local Delay for Interdom CDP-CDP 't' & 'p' conns (msec)........   27     
18 Max Local Delay for Interdom CDP-CDP 'a' conns (msec)..............   27     
19 Max Local Delay for Interdom CDP-CDP High Speed Data conns (msec)..   27     
20 Max Local Delay for Interdom High Speed Data conns (msec)..........   28     
21 FastPAD Jitter Buffer Size  (msec).................................   15     
22 Number of Consecutive Invalid Login Attempts to Cause Major Alarm .    0     
23 Enable Connection Deroute Delay feature ...........................   No     
24 Interval Statstics polling rate for ATM/Frame Relay VCs............    5     
25 Interval Statistics polling rate for ports.........................    5     
                                                                                
This Command: cnfsysparm                                                        
                                                                                
mulder         TN    StrataCom       IGX 8420  9.2.34    Date/Time Not Set      
                                                                                
1  Update Initial Delay   [ 5000] (D)   16 CC Redundancy Cnfged   [    Y] (Y/N) 
2  Update Per-Node Delay  [30000] (D)   17 MT3 Pass Through Relay [    Y] (Y/N) 
3  Comm-Break Test Delay  [30000] (D)   18 Nw Pkt Tx Rate (pps)   [  500] (D)   
4  Comm-Break Test Offset [   10] (D)   19 Stats Memory (x 100KB) [  130] (D)   
5  Network Timeout Period [ 1700] (D)   20 Standby Update Timer   [   10] (D)   
6  Network Inter-p Period [ 4000] (D)   21 Stby Updts Per Pass    [   50] (D)   
7  NW Sliding Window Size [    1] (D)   22 Gateway ID Timer       [   30] (D)   
8  Num Normal Timeouts    [    7] (D)   23 GLCON Alloc Timer      [   30] (D)   
9  Num Inter-p Timeouts   [    3] (D)   24 Comm Fail Delay        [   60] (D)   
10 Num Satellite Timeouts [    6] (D)   25 Nw Hdlr Timer (msec)   [  100] (D)   
11 Num Blind Timeouts     [    4] (D)   26 CBUS Delay (msec)      [   20] (D)   
12 Num CB Msg Timeouts    [    2] (D)   27 SNMP Event logging     [    Y] (Y/N) 
13 Comm Fail Interval     [10000] (D)   28 TFTP Grant Delay (sec) [    1] (D)   
14 Comm Fail Multiplier   [    3] (D)   29 TFTP ACK Timeout (sec) [   10] (D)   
15 Temperature Threshold  [   50] (D)   30 TFTP Write Retries     [    3] (D)   
 
31 FRP Link Status Alarm  [    Y] (Y/N) 46 Modem polling timer    [    1] (D)   
32 Job Lock Timeout       [ 1000] (D)   47 Verify CBA for non-FRP [    N] (Y/N) 
33 Max Via LCONs          [20000] (D)   48 Send Abit early        [    N] (Y/N) 
34 Max Blind Segment Size [ 3570] (D)   49 Abit Tmr Multiplier  M [    0] (D)   
35 Max XmtMemBlks per NIB [ 3000] (D)   50 Abit Tmr Granularity N [    3] (D)   
36 Max Mem on Stby Q (%)  [   33] (D)                                           
37 Trk Cell Rtng Restrict [    Y] (Y/N)                                         
38 Stat Config Proc Cnt   [ 1000] (D)                                           
39 Stat Config Proc Delay [ 2000] (D)                                           
40 Enable Degraded Mode   [    Y] (Y/N)                                         
41 Enable Rrt on Comm Fail[    N] (Y/N)                                         
42 Auto Switch on Degrade [    Y] (Y/N)                                         
43 Max Degraded Aborts    [  100] (D)                                           
44 Max Htls Rebuild Count [  100] (D)                                           
45 Htls Counter Reset Time[ 1000] (D)                                           
                                                                                
This Command: cnfnodeparm                                                       
                                                                                
mulder         TN    StrataCom       IGX 8420  9.2.34    Date/Time Not Set      
                                                                                
Index Status    Function                                                        
                                                                                
1     Enabled   Automatic CLN/PLN Loopback Test on Local/Remote Alarms          
2     Enabled   FDP Loopback button                                             
3     Enabled   User Command Logging                                            
4     Enabled   Automatic Card Reset on Hardware Error                          
5     Enabled   TXR Model D Download                                            
6     Enabled   Card Error Record Wraparound                                    
7     Disabled  Card Test After Failure                                         
8     Disabled  Download From Remote Cisco StrataView Plus                      
9     Disabled  Logging of conn events in local event log                       
10    Disabled  Logging of conn events in Cisco StrataView Plus event log       
11    Disabled  Logging SVC Connection Events                                   
12    Disabled  Force Download From a Specific IP address                       
13    Disabled  CDP WinkStart Signalling                                        
14    Enabled   Logging of Bus Diagnostic Events in local event log             
15    Enabled   Automatic Card Reset after Burnfw for CBI cards                 
                                                                                
This Command: cnffunc                                                           
                                                                                
mulder         TN    StrataCom       IGX 8420  9.2.34    Date/Time Not Set      
                                                                                
Index Status    Function                                                        
                                                                                
1     Disabled  Data Frame Multiplexing                                         
2     Disabled  Adaptive Voice                                                  
3     Enabled   Frame Relay                                                     
4     Disabled  Configuration Save/Restore                                      
5     Disabled  ForeSight                                                       
6     Disabled  Frame Relay Network-to-Network Interface                        
7     Disabled  Multiple VTs (1 session enabled)                                
8     Disabled  Interface Shelf                                                 
9     Enabled   Virtual Trunks                                                  
10    Disabled  ABR standard with VSVD                                          
                                                                                
This Command: cnfswfunc                                                         
                                                                                
mulder         TN    StrataCom       IGX 8420  9.2.34    Date/Time Not Set      
                                                                                
Card   Test    - - - - - - Self Test - - - - - - -   - - Background Test - - -  
Type   Freq    Enable        Inc   Thresh  Timeout   Enable        Inc   Thresh 
----   -----   --------  -------  -------  -------   --------  -------  ------- 
PSM      300   Enabled       100      300       31   N/A           100      300 
HDM      300   Enabled       100      300       80   Enabled       100      300 
LDM      300   Enabled       100      300       80   Enabled       100      300 
NTM      300   Enabled       100      300       31   N/A           100      300 
FRM      300   Enabled       100      300       80   Enabled       100      300 
MT3      300   Enabled       100      300       50   N/A           100      300 
CVM      300   Enabled       100      300      300   N/A           100      300 
NPM      180   Enabled       100      300      120   N/A           100      300 
ARM      300   Enabled       100      300       60   N/A           100      300 
BTM      300   Enabled       100      300      120   N/A           100      300 
FTM      300   Enabled       100      300       80   Disabled      100      300 
UFM      300   Enabled       100      300       80   Enabled       100      300 
UFMU     300   Enabled       100      300       80   Enabled       100      300 
ALM      300   Enabled       100      300      120   N/A           100      300 
UVM      300   Disabled      100      300       60   N/A           100      300 
UXM      300   Enabled       100      300      800   Enabled       100      300 
                                                                                
This Command: cnftstparm                                                        
                                                                                
mulder         TN    StrataCom       IGX 8420  9.2.34    Date/Time Not Set      
                                                                                
1  Normalization Interval    [    2] (D)                                        
2  Max Number To Normalize   [    5] (D)                                        
3  Normalization Logging     [   No]                                            
4  Settling Interval         [    4] (D)                                        
5  Minimum Open Space        [ 1000] (D)                                        
6  Normalization Priority    [ Load]                                            
7  Load Sample Period        [    4] (D)                                        
8  Maximum Routing Bundle    [   90] (D)                                        
9  Reroute Timer             [    0] (secs)                                     
10 Reset Timer on Line Fail  [  Yes]                                            
11 Max Down/Up Per Pass      [   50] (D)                                        
12 Down/Up Timer             [30000] (msecs)                                    
13 Max Route Errs per cycle  [  200] (D)                                        
14 Time between Rrt cycles   [    5] (mins)                                     
15 Max. Rrt Err cycles       [    1] (D)                                        
16 Routing pause timer       [    0] (msecs)                                    
17 Max msgs sent per update  [   10] (D)                                        
18 Send SVC urgent msg       [  Yes]                                            
19 Max SVC Retry             [    0] (D)                                        
20 Wait for TBL Updates      [   70] (100 msecs)                                
21 Max Derouting Bndl (0=all)[  500] (D)                                        
22 Enable Cost-Based Routing [   No]                                            
23 Enable Route Cache Usage  [   No]                                            
24 Use Delay for Routing     [   No]                                            
25 # of reroute groups used  [   50] (D)                                        
26 Starting size of RR grps  [    0] (CLU)                                      
27 Increment between RR grps [  100] (CLU)                                      
                                                                                
This Command: cnfcmparm                                                         
                                                                                
mulder         TN    StrataCom       IGX 8420  9.2.34    Date/Time Not Set      
                                                                                
1  Rmt Blk Freq (msec)     [    100]    16 FW Dnld Msgs/Block(dec) [      4]    
2  Rmt Blk Size (hex)      [    400]    17 Flash Write TO(msec)    [  16000]    
3  Lcl Blk Freq (msec)     [    100]    18 Flash Erase TO(msec)    [    100]    
4  Lcl Blk Size (hex)      [    400]    19 Erase Verify TO(msec)   [  16000]    
5  Image Req Freq (msec)   [  10000]    20 Standby Flash TO(sec)   [    300]    
6  Dnld Req Freq (msec)    [  10000]    21 Lcl Flash Init TO(msec) [   1000]    
7  Session Timeout (msec)  [  30000]    22 Flsh Write Blk Sz (hex) [  10000]    
8  Request Hop Limit (dec) [      1]    23 Flsh Verfy Blk Sz (hex) [    400]    
9  Crc Throttle Freq (dec) [   5000]    24 Chips Per Write/Erase   [      1]    
10 Crc Block Size (hex)    [    400]                                            
11 Rev Change Wait(dec)    [      0]                                            
12 CCs Switch Wait(dec)    [   1000]                                            
13 Lcl Response TO(msec)   [   5000]                                            
14 Rmt Response TO(msec)   [  30000]                                            
15 FW Dnld Block TO(msec)  [     50]                                            
                                                                                
This Command: cnfdlparm                                                         
                                                                                
mulder         TN    StrataCom       IGX 8420  9.2.34    Date/Time Not Set      
                                                                                
1. Logout Time ........... 20 minutes                                           
2. VT Logout Time ........ 4 minutes                                            
3. Prompt Time ........... 60 seconds                                           
4. Command Time .......... 3 minutes                                            
5. UID Privilege Level ... 6                                                    
6. Input Character Echo .. Enabled                                              
7. Screen Update Time .... 10 seconds                                           
                                                                                
This Command: cnfuiparm                                                         
                                                                                
mulder         TN    StrataCom       IGX 8420  9.2.34    Date/Time Not Set      
                                                                                
Function            Number   Status      Function            Number   Status    
Background Upcard     1      Enabled     Dynamic BW Allocation 15     Enabled   
Background Updates    2      Disabled    Modem Polling         16     Enabled   
Standby Terminal      3      Disabled    Conn Stat Sampling    17     Enabled   
Memory Protection     4      Enabled     SVC Del Bgnd Updates  18     Disabled  
Comm Break            5      Enabled     FastPAD Test          19     Enabled   
Comm Fail Test        6      Enabled     Neighbor Update Errs  20     Disabled  
BRAM Memory Protect   7      Enabled                                            
CRC Test              8      Enabled                                            
CDT Clock Test        9      Enabled                                            
Bus Fail Detection    10     Enabled                                            
Line Diag             11     Enabled                                            
Clock Restoral        12     Enabled                                            
Cm_Rerouting          13     Enabled                                            
Clock Routing         14     Enabled                                            
                                                                                
This Command: on1                                                               
                                                                                
mulder         TN    StrataCom       IGX 8420  9.2.34    Date/Time Not Set      
                                                                                
Function            Number   Status      Function            Number   Status    
Line Stat Sampling    1      Enabled     LAN Interface         15     Enabled   
Statistical Alarm     2      Enabled     Update Standby Stats  16     Enabled   
Job Ready Checker     3      Enabled     EIA Monitoring        17     Enabled   
Configuration  Backup 4      Enabled     Telnet Access         18     Enabled   
Standby Update        5      Enabled     Junction ID           19     Enabled   
Downloader            6      Enabled     Mult SV+/Routing Node 20     Enabled   
Cm Updates            7      Enabled     Feeder with NW Trunks 21     Disabled  
Power Supply Monitor  8      Enabled     Multiple Fdr Trunks   22     Disabled  
Topo/Stat Updates     9      Enabled     Simulated Fdr Trks    23     Disabled  
CDP/CIP Sig. Polling  10     Enabled     Auto Renum Fail Recov 24     Enabled   
Port Stat Sampling    11     Enabled     IGX - ACM Selftest    25     Enabled   
Robust Updates        12     Enabled     Card Simulation Tool  26     Enabled   
Robust Alarm Updates  13     Enabled     Major Alarm on NNI    27     Disabled  
Realtime Counters     14     Enabled     Deroute Delay         28     Enabled   
                                                                                
This Command: on2                                                               
                                                                                
mulder         TN    StrataCom       IGX 8420  9.2.34    Date/Time Not Set      
                                                                                
Function            Number   Status                                             
Region memory init    1      Disabled                                           
Trace Msg Sent        2      Disabled                                           
Multi-DB Stby Updates 3      Enabled                                            
AIT/BTM/ALM 32h Ext2  4      Enabled                                            
Card Synchronization  5      Disabled                                           
Loop Access Dev Init  6      Disabled                                           
Auto allocate UXM UBU 7      Disabled                                           
Trace Conv Msg        8      Disabled                                           
Automatic Cbus Diags  9      Disabled                                           
CBUS Flood Protection 10     Enabled                                            
                                                                                
This Command: on3

NTM-SR

mulder         TN    StrataCom       IGX 8420  9.2.34    Date/Time Not Set      
                                                                                
TRK  5 Config         SR/30    [10000 pps]  NTM slot:5                          
Subrate interface:    X.21                                                      
Subrate data rate:    1920 kbps                                                 
Pass sync:            No                                                        
Loop clock:           Yes                                                       
Statistical Reserve:  600                                                       
Routing Cost:         10                                                        
Restrict PCC traffic: No                                                        
Link type:            Terrestrial                                               
Traffic:              V,TS,NTS,FR,FST                                           
Deroute delay time:   0 seconds                                                 
                                                                                
Last Command: dsptrkcnf 5                                                       
                                                                                
mulder         TN    StrataCom       IGX 8420  9.2.34    Date/Time Not Set      
                                                                                
TRK  5 Parameters:                                                              
 1 Yel Alm-In/Out (D)  [  1000/  2000]     18 Red Alm-In/Out (D) [  1000/  2000]
 2 Rx Max Age - rt-VBR   (D)   [  N/A]     19 Tx Max Age - rt-VBR   (D)  [   20]
 3 Rx EFCN  - BdataB     (D)   [  N/A]     20 Tx EFCN    - BdataB   (D)  [   30]
 4 Gateway Efficiency    (D)   [  N/A]                                          
 5 EFCN     - Rx Space   (D)   [  N/A]     Tx Age Step2  (D)   Tx Age Step   (D)
 6 Low CLP  - Rx_Space   (%)   [  N/A]     21 BDataA [  128]   23 BDataA [  128]
 7 High CLP - Rx_Space   (%)   [  N/A]     22 BDataB [  128]   24 BDataB [  128]
Rx High CLP   (%)    Rx Low CLP    (%)     Tx High CLP   (%)   Tx Low CLP    (%)
 8 BDataA [  N/A]    10 BDataA [  N/A]     25 BDataA [  100]   27 BDataA [  100]
 9 BDataB [  N/A]    11 BdataB [  N/A]     26 BDataB [   75]   28 BDataB [   25]
Receive Queue Depth                (D)     Transmit Queue Depth              (D)
12 rt-VBR [  N/A]    15 BDataA [  N/A]     29 rt-VBR [   27]   32 BDataA [  600]
13 Non TS [  N/A]    16 BDataB [  N/A]     30 Non TS [   37]   33 BDataB [  600]
14 TS     [  N/A]    17 HighPri[  N/A]     31 TS     [ 2636]   34 HighPri[  100]
                                                                                
This Command: cnftrkparm 5

NTM-T1

mulder         TN    StrataCom       IGX 8420  9.2.34    Date/Time Not Set      
                                                                                
TRK  4 Config         E1/32    [10666 pps]  NTM slot:4                          
Line DS-0 map:        0-31                                                      
Pass sync:            Yes                                                       
Loop clock:           No                                                        
Statistical Reserve:  600    pps                                                
Routing Cost:         10                                                        
Idle code:            54 hex                                                    
Restrict PCC traffic: No                                                        
Link type:            Terrestrial                                               
Line coding:          HDB3                                                      
Line CRC:             No                                                        
Line recv impedance:  75 ohm + gnd                                              
Traffic:              V,TS,NTS,FR,FST                                           
Deroute delay time:   0 seconds                                                 
                                                                                
Last Command: dsptrkcnf 4                                                       
                                                                                
mulder         TN    StrataCom       IGX 8420  9.2.34    Date/Time Not Set      
                                                                                
TRK  4 Parameters:                                                              
 1 Yel Alm-In/Out (D)  [  1000/  2000]     18 Red Alm-In/Out (D) [  1000/  2000]
 2 Rx Max Age - rt-VBR   (D)   [  N/A]     19 Tx Max Age - rt-VBR   (D)  [   20]
 3 Rx EFCN  - BdataB     (D)   [  N/A]     20 Tx EFCN    - BdataB   (D)  [   30]
 4 Gateway Efficiency    (D)   [  N/A]                                          
 5 EFCN     - Rx Space   (D)   [  N/A]     Tx Age Step2  (D)   Tx Age Step   (D)
 6 Low CLP  - Rx_Space   (%)   [  N/A]     21 BDataA [  128]   23 BDataA [  128]
 7 High CLP - Rx_Space   (%)   [  N/A]     22 BDataB [  128]   24 BDataB [  128]
Rx High CLP   (%)    Rx Low CLP    (%)     Tx High CLP   (%)   Tx Low CLP    (%)
 8 BDataA [  N/A]    10 BDataA [  N/A]     25 BDataA [  100]   27 BDataA [  100]
 9 BDataB [  N/A]    11 BdataB [  N/A]     26 BDataB [   75]   28 BDataB [   25]
Receive Queue Depth                (D)     Transmit Queue Depth              (D)
12 rt-VBR [  N/A]    15 BDataA [  N/A]     29 rt-VBR [   28]   32 BDataA [  600]
13 Non TS [  N/A]    16 BDataB [  N/A]     30 Non TS [   40]   33 BDataB [  600]
14 TS     [  N/A]    17 HighPri[  N/A]     31 TS     [ 2632]   34 HighPri[  100]
                                                                                
This Command: cnftrkparm 4

NTM-E1

mulder         TN    StrataCom       IGX 8420  9.2.34    Date/Time Not Set      
                                                                                
TRK  4 Config         E1/32    [10666 pps]  NTM slot:4                          
Line DS-0 map:        0-31                                                      
Pass sync:            Yes                                                       
Loop clock:           No                                                        
Statistical Reserve:  600    pps                                                
Routing Cost:         10                                                        
Idle code:            54 hex                                                    
Restrict PCC traffic: No                                                        
Link type:            Terrestrial                                               
Line coding:          HDB3                                                      
Line CRC:             No                                                        
Line recv impedance:  75 ohm + gnd                                              
Traffic:              V,TS,NTS,FR,FST                                           
Deroute delay time:   0 seconds                                                 
                                                                                
Last Command: dsptrkcnf 4                                                       
                                                                                
mulder         TN    StrataCom       IGX 8420  9.2.34    Date/Time Not Set      
                                                                                
TRK  4 Parameters:                                                              
 1 Yel Alm-In/Out (D)  [  1000/  2000]     18 Red Alm-In/Out (D) [  1000/  2000]
 2 Rx Max Age - rt-VBR   (D)   [  N/A]     19 Tx Max Age - rt-VBR   (D)  [   20]
 3 Rx EFCN  - BdataB     (D)   [  N/A]     20 Tx EFCN    - BdataB   (D)  [   30]
 4 Gateway Efficiency    (D)   [  N/A]                                          
 5 EFCN     - Rx Space   (D)   [  N/A]     Tx Age Step2  (D)   Tx Age Step   (D)
 6 Low CLP  - Rx_Space   (%)   [  N/A]     21 BDataA [  128]   23 BDataA [  128]
 7 High CLP - Rx_Space   (%)   [  N/A]     22 BDataB [  128]   24 BDataB [  128]
Rx High CLP   (%)    Rx Low CLP    (%)     Tx High CLP   (%)   Tx Low CLP    (%)
 8 BDataA [  N/A]    10 BDataA [  N/A]     25 BDataA [  100]   27 BDataA [  100]
 9 BDataB [  N/A]    11 BdataB [  N/A]     26 BDataB [   75]   28 BDataB [   25]
Receive Queue Depth                (D)     Transmit Queue Depth              (D)
12 rt-VBR [  N/A]    15 BDataA [  N/A]     29 rt-VBR [   28]   32 BDataA [  600]
13 Non TS [  N/A]    16 BDataB [  N/A]     30 Non TS [   40]   33 BDataB [  600]
14 TS     [  N/A]    17 HighPri[  N/A]     31 TS     [ 2632]   34 HighPri[  100]
                                                                                
This Command: cnftrkparm 4

ALM/B-T3

mulder         TRM   StrataCom       IGX 8420  9.2.34    Date/Time Not Set
 
TRK  6 Config         T3/3     [1000  pps]  ALM slot:6                         
Transmit Trunk Rate:  96000  cps          HCS Masking:          Yes          
Rcv Trunk Rate:       1000   pps          Payload Scramble:     No           
Pass sync:            Yes                 Traffic:              V,TS,NTS,FR,FST
Loop clock:           No                  Deroute delay time:   0 seconds    
Statistical Reserve:  1000   pps         
Header Type:          STI                
Gateway Type:         BAM                
VPI Address:          0                  
VCI Address:          0                  
Routing Cost:         10                 
Idle code:            7F hex             
Restrict PCC traffic: No                 
Link type:            Terrestrial        
Line cable length:    0-225 ft.          
                                                                                
Last Command: dsptrkcnf 6
 
mulder         TRM   StrataCom       IGX 8420  9.2.34    Date/Time Not Set
 
TRK  6 Parameters:
 1 Yel Alm-In/Out (D)  [  2500/ 15000]     18 Red Alm-In/Out (D) [  2500/ 15000]
 2 Rx Max Age - rt-VBR   (D)   [   20]     19 Tx Max Age - rt-VBR   (D)  [   20]
 3 Rx EFCN  - BdataB     (D)   [   30]     20 Tx EFCN    - BdataB   (D)  [   30]
 4 Gateway Efficiency    (D)   [  2.0]
 5 EFCN     - Rx Space   (D)   [  N/A]     Tx Age Step2  (D)   Tx Age Step   (D)
 6 Low CLP  - Rx_Space   (%)   [  N/A]     21 BDataA [  N/A]   23 BDataA [  N/A]
 7 High CLP - Rx_Space   (%)   [  N/A]     22 BDataB [  N/A]   24 BDataB [  N/A]
Rx High CLP   (%)    Rx Low CLP    (%)     Tx High CLP   (%)   Tx Low CLP    (%)
 8 BDataA [  100]    10 BDataA [  100]     25 BDataA [  100]   27 BDataA [  100]
 9 BDataB [   75]    11 BdataB [   25]     26 BDataB [   75]   28 BDataB [   25]
Receive Queue Depth                (D)     Transmit Queue Depth              (D)
12 rt-VBR [    4]    15 BDataA [ 1000]     29 rt-VBR [  532]   32 BDataA [ 1000]
13 Non TS [    3]    16 BDataB [ 8000]     30 Non TS [  795]   33 BDataB [ 8000]
14 TS     [ 5993]    17 HighPri[ 1000]     31 TS     [ 4673]   34 HighPri[ 1000]
                                                                                
This Command: cnftrkparm 6

BTM-HSSI

mulder         TN    StrataCom       IGX 8420  9.2.34    Date/Time Not Set      
                                                                                
TRK  9 Config         HSSI/3   [1000  pps]  BTM slot:9                          
Clock Rate:           50840000 bps        Line cable length:    0-225 ft.       
Transmit Trunk Rate:  111491 cps          HCS Masking:          Yes             
Rcv Trunk Rate:       1000   pps          Payload Scramble:     No              
Pass sync:            No                  Traffic:              V,TS,NTS,FR,FST 
Loop clock:           No                  Deroute delay time:   0 seconds       
Statistical Reserve:  1000   pps                                                
Header Type:          STI                                                       
Gateway Type:         BAM                                                       
VPI Address:          0                                                         
VCI Address:          0                                                         
Routing Cost:         10                                                        
Idle code:            7F hex                                                    
Restrict PCC traffic: No                                                        
Link type:            Terrestrial                                               
                                                                                
Last Command: dsptrkcnf 9                                                       
                                                                                
mulder         TN    StrataCom       IGX 8420  9.2.34    Date/Time Not Set      
                                                                                
TRK  9 Parameters:                                                              
 1 Yel Alm-In/Out (D)  [  2500/ 15000]     18 Red Alm-In/Out (D) [  2500/ 15000]
 2 Rx Max Age - rt-VBR   (D)   [   20]     19 Tx Max Age - rt-VBR   (D)  [   20]
 3 Rx EFCN  - BdataB     (D)   [   30]     20 Tx EFCN    - BdataB   (D)  [   30]
 4 Gateway Efficiency    (D)   [  2.0]                                          
 5 EFCN     - Rx Space   (D)   [   30]     Tx Age Step2  (D)   Tx Age Step   (D)
 6 Low CLP  - Rx_Space   (%)   [  100]     21 BDataA [  N/A]   23 BDataA [  N/A]
 7 High CLP - Rx_Space   (%)   [  100]     22 BDataB [  N/A]   24 BDataB [  N/A]
Rx High CLP   (%)    Rx Low CLP    (%)     Tx High CLP   (%)   Tx Low CLP    (%)
 8 BDataA [  100]    10 BDataA [  100]     25 BDataA [  100]   27 BDataA [  100]
 9 BDataB [   75]    11 BdataB [   25]     26 BDataB [   75]   28 BDataB [   25]
Receive Queue Depth                (D)     Transmit Queue Depth              (D)
12 rt-VBR [    4]    15 BDataA [ 2264]     29 rt-VBR [  617]   32 BDataA [ 2264]
13 Non TS [    3]    16 BDataB [ 2264]     30 Non TS [  922]   33 BDataB [ 2264]
14 TS     [11365]    17 HighPri[  100]     31 TS     [ 9833]   34 HighPri[  100]
                                                                                
This Command: cnftrkparm 9

BTM-E1

mulder         TN    StrataCom       IGX 8420  9.2.34    Date/Time Not Set      
                                                                                
TRK 10 Config         E1/32    [10666 pps]  BTM slot:10                         
Line DS-0 map:        0-31                Line coding:          HDB3            
Transmit Trunk Rate:  4830   cps          Line CRC:             No              
Rcv Trunk Rate:       10666  pps          Line recv impedance:  75 ohm + gnd    
Pass sync:            Yes                 HCS Masking:          Yes             
Loop clock:           No                  Payload Scramble:     Yes             
Statistical Reserve:  600    pps          Traffic:              V,TS,NTS,FR,FST 
Header Type:          STI                 Deroute delay time:   0 seconds       
Gateway Type:         BAM                                                       
VPI Address:          0                                                         
VCI Address:          0                                                         
Routing Cost:         10                                                        
Idle code:            7F hex                                                    
Restrict PCC traffic: No                                                        
Link type:            Terrestrial                                               
                                                                                
Last Command: dsptrkcnf 10                                                      
                                                                                
mulder         TN    StrataCom       IGX 8420  9.2.34    Date/Time Not Set      
                                                                                
TRK 10 Parameters:                                                              
 1 Yel Alm-In/Out (D)  [  1000/  2000]     18 Red Alm-In/Out (D) [  1000/  2000]
 2 Rx Max Age - rt-VBR   (D)   [   20]     19 Tx Max Age - rt-VBR   (D)  [   20]
 3 Rx EFCN  - BdataB     (D)   [   30]     20 Tx EFCN    - BdataB   (D)  [   30]
 4 Gateway Efficiency    (D)   [  N/A]                                          
 5 EFCN     - Rx Space   (D)   [   30]     Tx Age Step2  (D)   Tx Age Step   (D)
 6 Low CLP  - Rx_Space   (%)   [  100]     21 BDataA [  N/A]   23 BDataA [  N/A]
 7 High CLP - Rx_Space   (%)   [  100]     22 BDataB [  N/A]   24 BDataB [  N/A]
Rx High CLP   (%)    Rx Low CLP    (%)     Tx High CLP   (%)   Tx Low CLP    (%)
 8 BDataA [  100]    10 BDataA [  100]     25 BDataA [  100]   27 BDataA [  100]
 9 BDataB [   75]    11 BdataB [   25]     26 BDataB [   75]   28 BDataB [   25]
Receive Queue Depth                (D)     Transmit Queue Depth              (D)
12 rt-VBR [   28]    15 BDataA [  600]     29 rt-VBR [   28]   32 BDataA [  600]
13 Non TS [   40]    16 BDataB [  600]     30 Non TS [   40]   33 BDataB [  600]
14 TS     [14632]    17 HighPri[  100]     31 TS     [14632]   34 HighPri[  100]
                                                                                
This Command: cnftrkparm 10

BTM-E2

mulder         TN    StrataCom       IGX 8420  9.2.34    Date/Time Not Set      
                                                                                
TRK 11 Config         E2/3     [1000  pps]  BTM slot:11                         
Transmit Trunk Rate:  19900  cps          HCS Masking:          Yes             
Rcv Trunk Rate:       1000   pps          Payload Scramble:     Yes             
Pass sync:            Yes                 Traffic:              V,TS,NTS,FR,FST 
Loop clock:           No                  Deroute delay time:   0 seconds       
Statistical Reserve:  1000   pps                                                
Header Type:          STI                                                       
Gateway Type:         BAM                                                       
VPI Address:          0                                                         
VCI Address:          0                                                         
Routing Cost:         10                                                        
Idle code:            7F hex                                                    
Restrict PCC traffic: No                                                        
Link type:            Terrestrial                                               
Line cable length:    0-225 ft.                                                 
                                                                                
Last Command: dsptrkcnf 11                                                      
                                                                                
mulder         TN    StrataCom       IGX 8420  9.2.34    Date/Time Not Set      
                                                                                
TRK 11 Parameters:                                                              
 1 Yel Alm-In/Out (D)  [  2500/ 15000]     18 Red Alm-In/Out (D) [  2500/ 15000]
 2 Rx Max Age - rt-VBR   (D)   [   20]     19 Tx Max Age - rt-VBR   (D)  [   20]
 3 Rx EFCN  - BdataB     (D)   [   30]     20 Tx EFCN    - BdataB   (D)  [   30]
 4 Gateway Efficiency    (D)   [  2.0]                                          
 5 EFCN     - Rx Space   (D)   [   30]     Tx Age Step2  (D)   Tx Age Step   (D)
 6 Low CLP  - Rx_Space   (%)   [  100]     21 BDataA [  N/A]   23 BDataA [  N/A]
 7 High CLP - Rx_Space   (%)   [  100]     22 BDataB [  N/A]   24 BDataB [  N/A]
Rx High CLP   (%)    Rx Low CLP    (%)     Tx High CLP   (%)   Tx Low CLP    (%)
 8 BDataA [  100]    10 BDataA [  100]     25 BDataA [  100]   27 BDataA [  100]
 9 BDataB [   75]    11 BdataB [   25]     26 BDataB [   75]   28 BDataB [   25]
Receive Queue Depth                (D)     Transmit Queue Depth              (D)
12 rt-VBR [    4]    15 BDataA [ 2264]     29 rt-VBR [  111]   32 BDataA [ 2264]
13 Non TS [    3]    16 BDataB [ 2264]     30 Non TS [  163]   33 BDataB [ 2264]
14 TS     [11365]    17 HighPri[  100]     31 TS     [11098]   34 HighPri[  100]
                                                                                
This Command: cnftrkparm 11

BTM-E3

mulder         TN    StrataCom       IGX 8420  9.2.34    Date/Time Not Set      
                                                                                
TRK  7 Config         E3/3     [1000  pps]  BTM slot:7                          
Transmit Trunk Rate:  80000  cps          HCS Masking:          Yes             
Rcv Trunk Rate:       1000   pps          Payload Scramble:     Yes             
Pass sync:            Yes                 Traffic:              V,TS,NTS,FR,FST 
Loop clock:           No                  Deroute delay time:   0 seconds       
Statistical Reserve:  1000   pps                                                
Header Type:          STI                                                       
Gateway Type:         BAM                                                       
VPI Address:          0                                                         
VCI Address:          0                                                         
Routing Cost:         10                                                        
Idle code:            7F hex                                                    
Restrict PCC traffic: No                                                        
Link type:            Terrestrial                                               
Line cable length:    0-225 ft.                                                 
                                                                                
Last Command: dsptrkcnf 7                                                       
                                                                                
mulder         TN    StrataCom       IGX 8420  9.2.34    Date/Time Not Set      
                                                                                
TRK  7 Parameters:                                                              
 1 Yel Alm-In/Out (D)  [  2500/ 15000]     18 Red Alm-In/Out (D) [  2500/ 15000]
 2 Rx Max Age - rt-VBR   (D)   [   20]     19 Tx Max Age - rt-VBR   (D)  [   20]
 3 Rx EFCN  - BdataB     (D)   [   30]     20 Tx EFCN    - BdataB   (D)  [   30]
 4 Gateway Efficiency    (D)   [  2.0]                                          
 5 EFCN     - Rx Space   (D)   [   30]     Tx Age Step2  (D)   Tx Age Step   (D)
 6 Low CLP  - Rx_Space   (%)   [  100]     21 BDataA [  N/A]   23 BDataA [  N/A]
 7 High CLP - Rx_Space   (%)   [  100]     22 BDataB [  N/A]   24 BDataB [  N/A]
Rx High CLP   (%)    Rx Low CLP    (%)     Tx High CLP   (%)   Tx Low CLP    (%)
 8 BDataA [  100]    10 BDataA [  100]     25 BDataA [  100]   27 BDataA [  100]
 9 BDataB [   75]    11 BdataB [   25]     26 BDataB [   75]   28 BDataB [   25]
Receive Queue Depth                (D)     Transmit Queue Depth              (D)
12 rt-VBR [    4]    15 BDataA [ 2264]     29 rt-VBR [  443]   32 BDataA [ 2264]
13 Non TS [    3]    16 BDataB [ 2264]     30 Non TS [  662]   33 BDataB [ 2264]
14 TS     [11365]    17 HighPri[  100]     31 TS     [10267]   34 HighPri[  100]
                                                                                
This Command: cnftrkparm 7

BTM-T3

mulder         TN    StrataCom       IGX 8420  9.2.34    Date/Time Not Set      
                                                                                
TRK  8 Config         T3/3     [1000  pps]  BTM slot:8                          
Transmit Trunk Rate:  96000               HCS Masking:          Yes             
Rcv Trunk Rate:       1000   pps          Payload Scramble:     No              
Pass sync:            Yes                 Traffic:              V,TS,NTS,FR,FST 
Loop clock:           No                  Deroute delay time:   0 seconds       
Statistical Reserve:  1000   pps                                                
Header Type:          STI                                                       
Gateway Type:         BAM                                                       
VPI Address:          0                                                         
VCI Address:          0                                                         
Routing Cost:         10                                                        
Idle code:            7F hex                                                    
Restrict PCC traffic: No                                                        
Link type:            Terrestrial                                               
Line cable length:    0-225 ft.                                                 
                                                                                
Last Command: dsptrkcnf 8                                                       
                                                                                
mulder         TN    StrataCom       IGX 8420  9.2.34    Date/Time Not Set      
                                                                                
TRK  8 Parameters:                                                              
 1 Yel Alm-In/Out (D)  [  2500/ 15000]     18 Red Alm-In/Out (D) [  2500/ 15000]
 2 Rx Max Age - rt-VBR   (D)   [   20]     19 Tx Max Age - rt-VBR   (D)  [   20]
 3 Rx EFCN  - BdataB     (D)   [   30]     20 Tx EFCN    - BdataB   (D)  [   30]
 4 Gateway Efficiency    (D)   [  2.0]                                          
 5 EFCN     - Rx Space   (D)   [   30]     Tx Age Step2  (D)   Tx Age Step   (D)
 6 Low CLP  - Rx_Space   (%)   [  100]     21 BDataA [  N/A]   23 BDataA [  N/A]
 7 High CLP - Rx_Space   (%)   [  100]     22 BDataB [  N/A]   24 BDataB [  N/A]
Rx High CLP   (%)    Rx Low CLP    (%)     Tx High CLP   (%)   Tx Low CLP    (%)
 8 BDataA [  100]    10 BDataA [  100]     25 BDataA [  100]   27 BDataA [  100]
 9 BDataB [   75]    11 BdataB [   25]     26 BDataB [   75]   28 BDataB [   25]
Receive Queue Depth                (D)     Transmit Queue Depth              (D)
12 rt-VBR [    4]    15 BDataA [ 2264]     29 rt-VBR [  532]   32 BDataA [ 2264]
13 Non TS [    3]    16 BDataB [ 2264]     30 Non TS [  795]   33 BDataB [ 2264]
14 TS     [11365]    17 HighPri[  100]     31 TS     [10045]   34 HighPri[  100]
                                                                                
This Command: cnftrkparm 8

UXM-E1 (using the E1-IMA backcard with only one physical line up)

mulder         TN    StrataCom       IGX 8420  9.2.34    Date/Time Not Set      
                                                                                
TRK 13.1 Config       E1/30    [4528  cps]  UXM slot:13                         
Line DS-0 map:        1-15,17-31          Line coding:          HDB3            
IMA Group Member(s):  1                   Line recv impedance:  120 ohm         
Retained links:       1                   HCS Masking:          Yes             
Transmit Trunk Rate:  4528   cps          Payload Scramble:     Yes             
Rcv Trunk Rate:       4528   cps          Connection Channels:  256             
Pass sync:            Yes                 Gateway Channels:     200             
Loop clock:           No                  Traffic:V,TS,NTS,FR,FST,CBR,N&RVBR,ABR
Statistical Reserve:  600    cps          IMA Protocol Option:  Disabled        
Header Type:          NNI                 IMA Max. Diff. Dly:   200 msec.       
VPI Address:          1                   IMA Clock Mode:       CTC             
Routing Cost:         10                  Deroute delay time:   0 seconds       
Idle code:            54 hex              VC Shaping:           No              
Restrict PCC traffic: No                  VPC Conns disabled:   No              
Link type:            Terrestrial                                               
                                                                                
Last Command: dsptrkcnf 13.1                                                    
                                                                                
mulder         TN    StrataCom       IGX 8420  9.2.34    Date/Time Not Set      
                                                                                
TRK 13.1 Parameters:                                                            
 1 Yel Alm-In/Out (D)  [  1000/  2000]     18 Red Alm-In/Out (D) [  1000/  2000]
 2 Rx Max Age - rt-VBR   (D)   [   20]     19 Tx Max Age - rt-VBR   (D)  [   20]
 3 Rx EFCN  - BdataB     (D)   [   20]     20 Tx EFCN    - BdataB   (%)  [   20]
 4 Gateway Efficiency    (D)   [  N/A]                                          
 5 EFCN     - Rx Space   (D)   [  N/A]     Tx Age Step2  (D)   Tx Age Step   (D)
 6 Low CLP/EPD- Rx_Space (%)   [  N/A]     21 BDataA [  N/A]   23 BDataA [  N/A]
 7 High CLP - Rx_Space   (%)   [  N/A]     22 BDataB [  N/A]   24 BDataB [  N/A]
Rx High CLP   (%)    Rx Low CLP/EPD(%)     Tx High CLP   (%)   Tx Low CLP/EPD(%)
 8 BDataA [   80]    10 BDataA [   60]     25 BDataA [   80]   27 BDataA [   60]
 9 BDataB [   80]    11 BdataB [   60]     26 BDataB [   80]   28 BDataB [   60]
Receive Queue Depth                (D)     Transmit Queue Depth              (D)
12 rt-VBR [   27]    15 BDataA [10000]     29 rt-VBR [   26]   32 BDataA [10000]
13 Non TS [   37]    16 BDataB [10000]     30 Non TS [   36]   33 BDataB [10000]
14 TS     [ 1000]    17 HighPri[ 1000]     31 TS     [ 1000]   34 HighPri[ 1000]
                                                                                
Rx Queue Depth(D)    Tx Queue Depth(D)    Rx EFCN       (%)    Tx EFCN       (%)
35 CBR    [  600]    38 CBR    [  600]                                          
36 nrt-VBR[ 5000]    39 nrt-VBR[ 5000]                                          
37 ABR    [20000]    40 ABR    [20000]    47 ABR    [   20]    48 ABR    [   20]
Rx High CLP   (%)    Rx Low CLP/EPD(%)    Tx High CLP   (%)    Tx Low CLP/EPD(%)
41 CBR    [   80]    44 CBR    [   60]    49 CBR    [   80]    52 CBR    [   60]
42 nrt-VBR[   80]    45 nrt-VBR[   60]    50 nrt-VBR[   80]    53 nrt-VBR[   60]
43 ABR    [   80]    46 ABR    [   60]    51 ABR    [   80]    54 ABR    [   60]
                                                                                
This Command: cnftrkparm 13.1

UXM/E1-IMA (4 physical lines up)

mulder         TRM   StrataCom       IGX 8420  9.2.34    Date/Time Not Set
 
TRK 13.1(4) Config    E1/119   [17962 cps]  UXM slot:13                        
Line DS-0 map:        1-15,17-31          Line coding:          HDB3         
IMA Group Member(s):  1-4                 Line recv impedance:  120 ohm      
Retained links:       4                   HCS Masking:          Yes          
Transmit Trunk Rate:  17962  cps          Payload Scramble:     Yes          
Rcv Trunk Rate:       17962  cps          Connection Channels:  256          
Pass sync:            Yes                 Gateway Channels:     200          
Loop clock:           No                  Traffic:V,TS,NTS,FR,FST,CBR,N&RVBR,ABR
Statistical Reserve:  600    cps          IMA Protocol Option:  Enabled      
Header Type:          NNI                 IMA Max. Diff. Dly:   200 msec.    
VPI Address:          1                   IMA Clock Mode:       CTC          
Routing Cost:         10                  Deroute delay time:   0 seconds    
Idle code:            54 hex              VC Shaping:           No           
Restrict PCC traffic: No                  VPC Conns disabled:   No           
Link type:            Terrestrial        
                                                                                
Last Command: dsptrkcnf 13.1
 
mulder         TRM   StrataCom       IGX 8420  9.2.34    Date/Time Not Set
 
TRK 13.1(4) Parameters:
 1 Yel Alm-In/Out (D)  [  1000/  2000]     18 Red Alm-In/Out (D) [  1000/  2000]
 2 Rx Max Age - rt-VBR   (D)   [   20]     19 Tx Max Age - rt-VBR   (D)  [   20]
 3 Rx EFCN  - BdataB     (D)   [   20]     20 Tx EFCN    - BdataB   (%)  [   20]
 4 Gateway Efficiency    (D)   [  N/A]
 5 EFCN     - Rx Space   (D)   [  N/A]     Tx Age Step2  (D)   Tx Age Step   (D)
 6 Low CLP/EPD- Rx_Space (%)   [  N/A]     21 BDataA [  N/A]   23 BDataA [  N/A]
 7 High CLP - Rx_Space   (%)   [  N/A]     22 BDataB [  N/A]   24 BDataB [  N/A]
Rx High CLP   (%)    Rx Low CLP/EPD(%)     Tx High CLP   (%)   Tx Low CLP/EPD(%)
 8 BDataA [   80]    10 BDataA [   60]     25 BDataA [   80]   27 BDataA [   60]
 9 BDataB [   80]    11 BdataB [   60]     26 BDataB [   80]   28 BDataB [   60]
Receive Queue Depth                (D)     Transmit Queue Depth              (D)
12 rt-VBR [  101]    15 BDataA [10000]     29 rt-VBR [  100]   32 BDataA [10000]
13 Non TS [  148]    16 BDataB [10000]     30 Non TS [  147]   33 BDataB [10000]
14 TS     [ 1000]    17 HighPri[ 1000]     31 TS     [ 1000]   34 HighPri[ 1000]
 
Rx Queue Depth(D)    Tx Queue Depth(D)    Rx EFCN       (%)    Tx EFCN       (%)
35 CBR    [  600]    38 CBR    [  600]
36 nrt-VBR[ 5000]    39 nrt-VBR[ 5000]
37 ABR    [20000]    40 ABR    [20000]    47 ABR    [   20]    48 ABR    [   20]
Rx High CLP   (%)    Rx Low CLP/EPD(%)    Tx High CLP   (%)    Tx Low CLP/EPD(%)
41 CBR    [   80]    44 CBR    [   60]    49 CBR    [   80]    52 CBR    [   60]
42 nrt-VBR[   80]    45 nrt-VBR[   60]    50 nrt-VBR[   80]    53 nrt-VBR[   60]
43 ABR    [   80]    46 ABR    [   60]    51 ABR    [   80]    54 ABR    [   60]
 
This Command: cnftrkparm 13.1

UXM-T1 (using the T1-IMA backcard with only one physical line up)

mulder       TN    StrataCom       IGX 8420  9.2.33    Date/Time Not Set      
                                                                                
TRK 11.1 Config       T1/24    [3622  cps]  UXM slot:11                         
IMA Group Member(s):  1                   Line coding:          B8ZS            
Retained links:       1                   Line cable type:      ABAM            
Transmit Trunk Rate:  3622   cps          Line cable length:    0-131 ft.       
Rcv Trunk Rate:       3622   cps          HCS Masking:          Yes             
Pass sync:            Yes                 Payload Scramble:     No              
Loop clock:           No                  Connection Channels:  256             
Statistical Reserve:  600    cps          Gateway Channels:     200             
Header Type:          NNI                 Traffic:V,TS,NTS,FR,FST,CBR,N&RVBR,ABR
VPI Address:          1                   IMA Protocol Option:  Disabled        
Routing Cost:         10                  IMA Max. Diff. Dly:   200 msec.       
Idle code:            7F hex              IMA Clock Mode:       CTC             
Restrict PCC traffic: No                  Deroute delay time:   0 seconds       
Link type:            Terrestrial         VC Shaping:           No              
Line framing:         ESF                 VPC Conns disabled:   No              
                                                                                
Last Command: dsptrkcnf 11.1                                                    
                                                                                
mulder       TN    StrataCom       IGX 8420  9.2.33    Date/Time Not Set      
                                                                                
TRK 11.1 Parameters:                                                            
 1 Yel Alm-In/Out (D)  [   600/   600]     18 Red Alm-In/Out (D) [  2500/ 15000]
 2 Rx Max Age - rt-VBR   (D)   [   20]     19 Tx Max Age - rt-VBR   (D)  [   20]
 3 Rx EFCN  - BdataB     (D)   [   20]     20 Tx EFCN    - BdataB   (%)  [   20]
 4 Gateway Efficiency    (D)   [  2.0]                                          
 5 EFCN     - Rx Space   (D)   [  N/A]     Tx Age Step2  (D)   Tx Age Step   (D)
 6 Low CLP/EPD- Rx_Space (%)   [  N/A]     21 BDataA [  N/A]   23 BDataA [  N/A]
 7 High CLP - Rx_Space   (%)   [  N/A]     22 BDataB [  N/A]   24 BDataB [  N/A]
Rx High CLP   (%)    Rx Low CLP/EPD(%)     Tx High CLP   (%)   Tx Low CLP/EPD(%)
 8 BDataA [   80]    10 BDataA [   60]     25 BDataA [   80]   27 BDataA [   60]
 9 BDataB [   80]    11 BdataB [   60]     26 BDataB [   80]   28 BDataB [   60]
Receive Queue Depth                (D)     Transmit Queue Depth              (D)
12 rt-VBR [   22]    15 BDataA [10000]     29 rt-VBR [   21]   32 BDataA [10000]
13 Non TS [   30]    16 BDataB [10000]     30 Non TS [   28]   33 BDataB [10000]
14 TS     [ 1000]    17 HighPri[ 1000]     31 TS     [ 1000]   34 HighPri[ 1000]
Rx Queue Depth(D)    Tx Queue Depth(D)    Rx EFCN       (%)    Tx EFCN       (%)
 
35 CBR    [  600]    38 CBR    [  600]                                          
36 nrt-VBR[ 5000]    39 nrt-VBR[ 5000]                                          
37 ABR    [20000]    40 ABR    [20000]    47 ABR    [   20]    48 ABR    [   20]
Rx High CLP   (%)    Rx Low CLP/EPD(%)    Tx High CLP   (%)    Tx Low CLP/EPD(%)
41 CBR    [   80]    44 CBR    [   60]    49 CBR    [   80]    52 CBR    [   60]
42 nrt-VBR[   80]    45 nrt-VBR[   60]    50 nrt-VBR[   80]    53 nrt-VBR[   60]
43 ABR    [   80]    46 ABR    [   60]    51 ABR    [   80]    54 ABR    [   60]
                                                                                
This Command: cnftrkparm 11.1

UXM/T1-IMA (4 physical lines up)

mulder       TN    StrataCom       IGX 8420  9.2.33    Date/Time Not Set
 
TRK 11.1(4) Config    T1/95    [14339 cps]  UXM slot:11                        
IMA Group Member(s):  1-4                 Line coding:          B8ZS         
Retained links:       4                   Line cable type:      ABAM         
Transmit Trunk Rate:  14339  cps          Line cable length:    0-131 ft.    
Rcv Trunk Rate:       14339  cps          HCS Masking:          Yes          
Pass sync:            Yes                 Payload Scramble:     No           
Loop clock:           No                  Connection Channels:  256          
Statistical Reserve:  600    cps          Gateway Channels:     200          
Header Type:          NNI                 Traffic:V,TS,NTS,FR,FST,CBR,N&RVBR,ABR
VPI Address:          1                   IMA Protocol Option:  Enabled      
Routing Cost:         10                  IMA Max. Diff. Dly:   200 msec.    
Idle code:            7F hex              IMA Clock Mode:       CTC          
Restrict PCC traffic: No                  Deroute delay time:   0 seconds    
Link type:            Terrestrial         VC Shaping:           No           
Line framing:         ESF                 VPC Conns disabled:   No           
                                                                                
Last Command: dsptrkcnf 11.1
 
mulder       TN    StrataCom       IGX 8420  9.2.33    Date/Time Not Set
 
TRK 11.1(4) Parameters:
 1 Yel Alm-In/Out (D)  [   600/   600]     18 Red Alm-In/Out (D) [  2500/ 15000]
 2 Rx Max Age - rt-VBR   (D)   [   20]     19 Tx Max Age - rt-VBR   (D)  [   20]
 3 Rx EFCN  - BdataB     (D)   [   20]     20 Tx EFCN    - BdataB   (%)  [   20]
 4 Gateway Efficiency    (D)   [  2.0]
 5 EFCN     - Rx Space   (D)   [  N/A]     Tx Age Step2  (D)   Tx Age Step   (D)
 6 Low CLP/EPD- Rx_Space (%)   [  N/A]     21 BDataA [  N/A]   23 BDataA [  N/A]
 7 High CLP - Rx_Space   (%)   [  N/A]     22 BDataB [  N/A]   24 BDataB [  N/A]
Rx High CLP   (%)    Rx Low CLP/EPD(%)     Tx High CLP   (%)   Tx Low CLP/EPD(%)
 8 BDataA [   80]    10 BDataA [   60]     25 BDataA [   80]   27 BDataA [   60]
 9 BDataB [   80]    11 BdataB [   60]     26 BDataB [   80]   28 BDataB [   60]
Receive Queue Depth                (D)     Transmit Queue Depth              (D)
12 rt-VBR [   81]    15 BDataA [10000]     29 rt-VBR [   80]   32 BDataA [10000]
13 Non TS [  118]    16 BDataB [10000]     30 Non TS [  117]   33 BDataB [10000]
14 TS     [ 1000]    17 HighPri[ 1000]     31 TS     [ 1000]   34 HighPri[ 1000]
 
Rx Queue Depth(D)    Tx Queue Depth(D)    Rx EFCN       (%)    Tx EFCN       (%)
35 CBR    [  600]    38 CBR    [  600]
36 nrt-VBR[ 5000]    39 nrt-VBR[ 5000]
37 ABR    [20000]    40 ABR    [20000]    47 ABR    [   20]    48 ABR    [   20]
Rx High CLP   (%)    Rx Low CLP/EPD(%)    Tx High CLP   (%)    Tx Low CLP/EPD(%)
41 CBR    [   80]    44 CBR    [   60]    49 CBR    [   80]    52 CBR    [   60]
42 nrt-VBR[   80]    45 nrt-VBR[   60]    50 nrt-VBR[   80]    53 nrt-VBR[   60]
43 ABR    [   80]    46 ABR    [   60]    51 ABR    [   80]    54 ABR    [   60]
 
This Command: cnftrkparm 11.1

UXM-T3

mulder         TN    StrataCom       IGX 8420  9.2.34    Date/Time Not Set      
                                                                                
TRK 14.1 Config       T3/636   [96000 cps]  UXM slot:14                         
Transmit Trunk Rate:  96000  cps          Payload Scramble:     No              
Rcv Trunk Rate:       96000  cps          Connection Channels:  256             
Pass sync:            Yes                 Gateway Channels:     200             
Loop clock:           No                  Traffic:V,TS,NTS,FR,FST,CBR,N&RVBR,ABR
Statistical Reserve:  1000   cps          Deroute delay time:   0 seconds       
Header Type:          NNI                 VC Shaping:           No              
VPI Address:          1                   VPC Conns disabled:   No              
Routing Cost:         10                                                        
Idle code:            7F hex                                                    
Restrict PCC traffic: No                                                        
Link type:            Terrestrial                                               
Line framing:         PLCP                                                      
Line cable length:    0-225 ft.                                                 
HCS Masking:          Yes                                                       
                                                                                
Last Command: dsptrkcnf 14.1                                                    
                                                                                
mulder         TN    StrataCom       IGX 8420  9.2.34    Date/Time Not Set      
                                                                                
TRK 14.1 Parameters:                                                            
 1 Yel Alm-In/Out (D)  [  2500/ 15000]     18 Red Alm-In/Out (D) [  2500/ 15000]
 2 Rx Max Age - rt-VBR   (D)   [   20]     19 Tx Max Age - rt-VBR   (D)  [   20]
 3 Rx EFCN  - BdataB     (D)   [   20]     20 Tx EFCN    - BdataB   (%)  [   20]
 4 Gateway Efficiency    (D)   [  2.0]                                          
 5 EFCN     - Rx Space   (D)   [  N/A]     Tx Age Step2  (D)   Tx Age Step   (D)
 6 Low CLP/EPD- Rx_Space (%)   [  N/A]     21 BDataA [  N/A]   23 BDataA [  N/A]
 7 High CLP - Rx_Space   (%)   [  N/A]     22 BDataB [  N/A]   24 BDataB [  N/A]
Rx High CLP   (%)    Rx Low CLP/EPD(%)     Tx High CLP   (%)   Tx Low CLP/EPD(%)
 8 BDataA [   80]    10 BDataA [   60]     25 BDataA [   80]   27 BDataA [   60]
 9 BDataB [   80]    11 BdataB [   60]     26 BDataB [   80]   28 BDataB [   60]
Receive Queue Depth                (D)     Transmit Queue Depth              (D)
12 rt-VBR [  532]    15 BDataA [10000]     29 rt-VBR [  532]   32 BDataA [10000]
13 Non TS [  795]    16 BDataB [10000]     30 Non TS [  795]   33 BDataB [10000]
14 TS     [ 1000]    17 HighPri[ 1000]     31 TS     [ 1000]   34 HighPri[ 1000]
                                                                                
Rx Queue Depth(D)    Tx Queue Depth(D)    Rx EFCN       (%)    Tx EFCN       (%)
35 CBR    [  600]    38 CBR    [  600]                                          
36 nrt-VBR[ 5000]    39 nrt-VBR[ 5000]                                          
37 ABR    [20000]    40 ABR    [20000]    47 ABR    [   20]    48 ABR    [   20]
Rx High CLP   (%)    Rx Low CLP/EPD(%)    Tx High CLP   (%)    Tx Low CLP/EPD(%)
41 CBR    [   80]    44 CBR    [   60]    49 CBR    [   80]    52 CBR    [   60]
42 nrt-VBR[   80]    45 nrt-VBR[   60]    50 nrt-VBR[   80]    53 nrt-VBR[   60]
43 ABR    [   80]    46 ABR    [   60]    51 ABR    [   80]    54 ABR    [   60]
                                                                                
This Command: cnftrkparm 14.1

UXM-E3

mulder         TN    StrataCom       IGX 8420  9.2.34    Date/Time Not Set      
                                                                                
TRK 15.1 Config       E3/530   [80000 cps]  UXM slot:15                         
Transmit Trunk Rate:  80000  cps          Payload Scramble:     Yes             
Rcv Trunk Rate:       80000  cps          Connection Channels:  256             
Pass sync:            Yes                 Gateway Channels:     200             
Loop clock:           No                  Traffic:V,TS,NTS,FR,FST,CBR,N&RVBR,ABR
Statistical Reserve:  1000   cps          Deroute delay time:   0 seconds       
Header Type:          NNI                 VC Shaping:           No              
VPI Address:          1                   VPC Conns disabled:   No              
Routing Cost:         10                                                        
Idle code:            7F hex                                                    
Restrict PCC traffic: No                                                        
Link type:            Terrestrial                                               
Line framing:         HEC                                                       
Line cable length:    0-225 ft.                                                 
HCS Masking:          Yes                                                       
                                                                                
Last Command: dsptrkcnf 15.1                                                    
                                                                                
mulder         TN    StrataCom       IGX 8420  9.2.34    Date/Time Not Set      
                                                                                
TRK 15.1 Parameters:                                                            
 1 Yel Alm-In/Out (D)  [  2500/ 15000]     18 Red Alm-In/Out (D) [  2500/ 15000]
 2 Rx Max Age - rt-VBR   (D)   [   20]     19 Tx Max Age - rt-VBR   (D)  [   20]
 3 Rx EFCN  - BdataB     (D)   [   20]     20 Tx EFCN    - BdataB   (%)  [   20]
 4 Gateway Efficiency    (D)   [  2.0]                                          
 5 EFCN     - Rx Space   (D)   [  N/A]     Tx Age Step2  (D)   Tx Age Step   (D)
 6 Low CLP/EPD- Rx_Space (%)   [  N/A]     21 BDataA [  N/A]   23 BDataA [  N/A]
 7 High CLP - Rx_Space   (%)   [  N/A]     22 BDataB [  N/A]   24 BDataB [  N/A]
Rx High CLP   (%)    Rx Low CLP/EPD(%)     Tx High CLP   (%)   Tx Low CLP/EPD(%)
 8 BDataA [   80]    10 BDataA [   60]     25 BDataA [   80]   27 BDataA [   60]
 9 BDataB [   80]    11 BdataB [   60]     26 BDataB [   80]   28 BDataB [   60]
Receive Queue Depth                (D)     Transmit Queue Depth              (D)
12 rt-VBR [  443]    15 BDataA [10000]     29 rt-VBR [  443]   32 BDataA [10000]
13 Non TS [  662]    16 BDataB [10000]     30 Non TS [  662]   33 BDataB [10000]
14 TS     [ 1000]    17 HighPri[ 1000]     31 TS     [ 1000]   34 HighPri[ 1000]
                                                                                
Rx Queue Depth(D)    Tx Queue Depth(D)    Rx EFCN       (%)    Tx EFCN       (%)
35 CBR    [  600]    38 CBR    [  600]                                          
36 nrt-VBR[ 5000]    39 nrt-VBR[ 5000]                                          
37 ABR    [20000]    40 ABR    [20000]    47 ABR    [   20]    48 ABR    [   20]
Rx High CLP   (%)    Rx Low CLP/EPD(%)    Tx High CLP   (%)    Tx Low CLP/EPD(%)
41 CBR    [   80]    44 CBR    [   60]    49 CBR    [   80]    52 CBR    [   60]
42 nrt-VBR[   80]    45 nrt-VBR[   60]    50 nrt-VBR[   80]    53 nrt-VBR[   60]
43 ABR    [   80]    46 ABR    [   60]    51 ABR    [   80]    54 ABR    [   60]
                                                                                
This Command: cnftrkparm 15.1

UXM-OC3

mulder         TN    StrataCom       IGX 8420  9.2.34    Date/Time Not Set      
                                                                                
TRK 16.1 Config       OC3      [353207cps]  UXM slot:16                         
Transmit Trunk Rate:  353208 cps          Connection Channels:  256             
Rcv Trunk Rate:       353207 cps          Gateway Channels:     200             
Pass sync:            Yes                 Traffic:V,TS,NTS,FR,FST,CBR,N&RVBR,ABR
Loop clock:           No                  Frame Scramble:       Yes             
Statistical Reserve:  1000   cps          Deroute delay time:   0 seconds       
Header Type:          NNI                 VC Shaping:           No              
VPI Address:          1                   VPC Conns disabled:   No              
Routing Cost:         10                                                        
Idle code:            7F hex                                                    
Restrict PCC traffic: No                                                        
Link type:            Terrestrial                                               
Line framing:         STS-3C                                                    
HCS Masking:          Yes                                                       
Payload Scramble:     Yes                                                       
                                                                                
Last Command: dsptrkcnf 16.1                                                    
                                                                                
mulder         TN    StrataCom       IGX 8420  9.2.34    Date/Time Not Set      
                                                                                
TRK 16.1 Parameters:                                                            
 1 Yel Alm-In/Out (D)  [  2500/ 10000]     18 Red Alm-In/Out (D) [  2500/ 10000]
 2 Rx Max Age - rt-VBR   (D)   [   20]     19 Tx Max Age - rt-VBR   (D)  [   20]
 3 Rx EFCN  - BdataB     (D)   [   20]     20 Tx EFCN    - BdataB   (%)  [   20]
 4 Gateway Efficiency    (D)   [  2.0]                                          
 5 EFCN     - Rx Space   (D)   [  N/A]     Tx Age Step2  (D)   Tx Age Step   (D)
 6 Low CLP/EPD- Rx_Space (%)   [  N/A]     21 BDataA [  N/A]   23 BDataA [  N/A]
 7 High CLP - Rx_Space   (%)   [  N/A]     22 BDataB [  N/A]   24 BDataB [  N/A]
Rx High CLP   (%)    Rx Low CLP/EPD(%)     Tx High CLP   (%)   Tx Low CLP/EPD(%)
 8 BDataA [   80]    10 BDataA [   60]     25 BDataA [   80]   27 BDataA [   60]
 9 BDataB [   80]    11 BdataB [   60]     26 BDataB [   80]   28 BDataB [   60]
Receive Queue Depth                (D)     Transmit Queue Depth              (D)
12 rt-VBR [ 1952]    15 BDataA [10000]     29 rt-VBR [ 1952]   32 BDataA [10000]
13 Non TS [ 2925]    16 BDataB [10000]     30 Non TS [ 2925]   33 BDataB [10000]
14 TS     [ 1000]    17 HighPri[ 1000]     31 TS     [ 1000]   34 HighPri[ 1000]
                                                                                
Rx Queue Depth(D)    Tx Queue Depth(D)    Rx EFCN       (%)    Tx EFCN       (%)
35 CBR    [  600]    38 CBR    [  600]                                          
36 nrt-VBR[ 5000]    39 nrt-VBR[ 5000]                                          
37 ABR    [20000]    40 ABR    [20000]    47 ABR    [   20]    48 ABR    [   20]
Rx High CLP   (%)    Rx Low CLP/EPD(%)    Tx High CLP   (%)    Tx Low CLP/EPD(%)
41 CBR    [   80]    44 CBR    [   60]    49 CBR    [   80]    52 CBR    [   60]
42 nrt-VBR[   80]    45 nrt-VBR[   60]    50 nrt-VBR[   80]    53 nrt-VBR[   60]
43 ABR    [   80]    46 ABR    [   60]    51 ABR    [   80]    54 ABR    [   60]
                                                                                
                                                                                
This Command: cnftrkparm 16.1

Obtaining Service and Support

For service and support for a product purchased from a reseller, contact the reseller. Resellers offer a wide variety of Cisco service and support programs, which are described in the section "Service and Support" in the information packet that shipped with your chassis.

Note   If you purchased your product from a reseller, you can access Cisco Connection Online (CCO) as a guest. CCO is Cisco Systems' primary, real-time support channel. Your reseller offers programs that include direct access to CCO's services.

For service and support for a product purchased directly from Cisco, use CCO.

Cisco Connection Online

Cisco Connection Online (CCO) is Cisco Systems' primary, real-time support channel. Maintenance customers and partners can self-register on CCO to obtain additional information and services.

Available 24 hours a day, 7 days a week, CCO provides a wealth of standard and value-added services to Cisco's customers and business partners. CCO services include product information, product documentation, software updates, release notes, technical tips, the Bug Navigator, configuration notes, brochures, descriptions of service offerings, and download access to public and authorized files.

CCO serves a wide variety of users through two interfaces that are updated and enhanced simultaneously: a character-based version and a multimedia version that resides on the World Wide Web (WWW). The character-based CCO supports Zmodem, Kermit, Xmodem, FTP, and Internet e-mail, and it is excellent for quick access to information over lower bandwidths. The WWW version of CCO provides richly formatted documents with photographs, figures, graphics, and video, as well as hyperlinks to related information.

You can access CCO in the following ways:

For a copy of CCO's Frequently Asked Questions (FAQ), contact cco-help@cisco.com. For additional information, contact cco-team@cisco.com.

Note   If you are a network administrator and need personal technical assistance with a Cisco product that is under warranty or covered by a maintenance contract, contact Cisco's Technical Assistance Center (TAC) at 800 553-2447, 408 526-7209, or tac@cisco.com. To obtain general information about Cisco Systems, Cisco products, or upgrades, contact 800 553-6387, 408 526-7208, or cs-rep@cisco.com.


hometocprevnextglossaryfeedbacksearchhelp
Posted: Fri Aug 18 11:18:13 PDT 2000
Copyright 1989-2000©Cisco Systems Inc.