Table of Contents

Before You Begin
Stopping the uOne Services
Modifying the SSMWI.ini File
Modifying the SS.ini File
Modifying the DialMap.ini File

4-Digit Dial Plan
5-Digit Dial Plan

Restarting the uOne Services
Completing the Configuration

Configuring uOne

In order for uOne Corporate Edition 4.1E to operate properly with CallManager, you need to edit relevant .ini files to set parameters for the uOne system. The .ini files are located in C:\CiscoSystems\uOne\parms folder. The process of configuring uOne includes the following:

• Stopping All Services

• Modifying the SSMWI.ini File

• Modifying the SS.ini File

• Modifying the DialMap.ini File

• Restarting the Services

• Completing the Messaging Configuration

Tips For more information about the .ini files and their functionality, please refer to the "The .ini Files" chapter of the uOne Administration and Operations, Corporate Edition 4.1E for CallManager 3.0 guide.

Before You Begin

Before you set up the .ini files, you need to gather the dialing information for your system. Use the Software Configuration Worksheet on Table 2-1 as a worksheet for the software configuration information necessary for modifying the .ini files for uOne. This worksheet will also be used when making configuration settings for CallManager in the "Configuring CallManager" chapter of this guide.

The Software Configuration Worksheet table shows the different parameter information needed to configure your system. For each parameter listed, the table gives the uOne .ini file location and expression where the parameter should be placed, the CallManager Administration location for that information, and the default value for the parameter. A space is provided for you to enter your value for that parameter as it applies to your system.

Stopping the uOne Services

Before editing the following .ini files, be sure that each of the uOne processes has been turned off. By stopping the uTel process first, you receive a prompt confirming that by stopping the uTel process, the uPilot, uLite, and uLogRemover processes will also be stopped. To stop the processes, follow these steps.

Step 2 Select Settings, then Control Panel.

Step 3 Select the Services icon.

Step 4 Select the uTel process first; then click Stop.

Step 5 At the confirmation prompt for Stopping Services, confirm that all of the following processes will be stopped: uTel, uLite, uLogRemover, and uPilot.

Step 6 Click OK to stop these processes.

Step 7 Close the Control Panel.

Modifying the SSMWI.ini File

You can set the numbers that turn the Message Waiting Indicator (MWI) on or off by editing the SSMWI.ini file. To change the values of the MWI On/Off features in the SSMWI.ini file, perform the following steps.

Step 2 Select the Run menu in the popup menu.

Step 3 Type in Wordpad, and click OK.

Step 4 From within Wordpad, select Open from the File menu, and navigate to C:\CiscoSystems\uOne\parms\SSMWI.ini.

Step 5 Locate the section [Device0] and find the key for CMDeviceName. Be sure the CMDeviceName for the message waiting indicator in the SSMWI.ini file reflects your value from the Software Configuration Worksheet, Table 2-1.

Step 6 For the CMMWIOnNumber key, enter your value from the Software Configuration Worksheet, Table 2-1, for the CMMWIOnNumber for the message waiting indicator.

Step 7 For the CMMWIOffNumber key, enter your value from the Software Configuration Worksheet, Table 2-1, for the CMMWIOffNumber for the message waiting indicator.

Step 8 Save the .ini file and exit the text editor.

Modifying the SS.ini File

This .ini file contains skinny station configuration settings. The information entered in this file is also used when you configure CallManager devices using the CallManager Administration menus.

Note It is extremely important that the information in the SS.ini file match the CallManager configurations.

To modify the SS.ini file, follow these steps.

Step 2 Select the Run menu in the popup menu.

Step 3 Type in Wordpad, and click OK.

Step 4 From within Wordpad, select Open from the File menu, and navigate to C:\CiscoSystems\uOne\parms\SS.ini.

Step 5 Review the information in the [SS] section to be sure it is accurate for your system configuration.

Step 6 Find the key for CMDeviceName. Be sure the CMDeviceName value in the SS.ini file reflects your value from the Software Configuration Worksheet, Table 2-1.

Step 7 Save the .ini file and exit your text editor.

Modifying the DialMap.ini File

The DialMap.ini file contains the dialing plans for your installation. Since default settings are placed in the Dialmap.ini file for pilot numbers and some return values, you need to modify this file to conform to your dial plan. For more information about the DialMap.ini file, see "The .ini Files" chapter of the uOne Administration and Operations, Corporate Edition 4.1E for CallManager 3.0 manual.

The uOne installation provides sample .ini files for use in configuring 4-digit or 5-digit dialing plans. These sample .ini files can be found in the C:\CiscoSystems\uOne\parms directory. The default DialMap.ini file for uOne is configured for 4-digit dialing.

4-Digit Dial Plan

The following steps implement modifications for the default DialMap.ini file which uses a 4-digit dialing plan. These modifications ensure that uOne conforms to your dialing plan configuration.

Step 2 Type in Wordpad, and click OK.

Step 3 From within Wordpad, select Open from the File menu, and navigate to C:\CiscoSystems\uOne\parms\DialMap.ini.

Step 4 Change the ToRegExp value for the [USDOMESTIC:OfficePBX4] section to reflect your 3-digit area code and 3-digit exchange---for example, ^804762([0-9]{4})$0$.

Note The USDOMESTIC section of the DialMap.ini file is closely integrated with the dial mapping information in CallManager.

Step 5 Change the Return value for the [DialPlan:Rule1] section to reflect your 3-digit area code and 3-digit exchange---for example, 804762$t0.

Step 6 Change the Return value for the [SKINNYCALLINGPARTY:4Digits] section to your 3-digit area code and 3-digit exchange---for example, 804762$t0.

Step 7 Change the Return value for the [SKINNYCALLEDPARTY:4Digits] section to reflect your 3-digit area code and 3-digit exchange---for example, 804762$f0.

Step 8 In the [SKINNYCALLTYPE:VoiceMail] section, change FromRegExp to include the pilot number for voice mail for your system---for example, ^(2501)$0$.

Step 9 In the [SKINNYCALLTYPE:Forwarded] section, change Constraint to include the pilot number for your system---for example ($f0 != 2501).

Step 10 In the [MWI:4Digits] section, change the FromRegExp value to reflect your 3-digit area code and 3-digit exchange---for example, ^804762([0-9]{4})$0$.

Step 11 Save and close the file.

The following are example sections which you need to edit for the 4-digit dialing plan.

5-Digit Dial Plan

The following steps describe modifications to the DialMap.ini file to conform to a 5-digit dialing plan.

Step 2 Click the Start button in the Windows task bar to get the Start popup menu.

Step 3 Select the Run menu in the popup menu.

Step 4 Type in Wordpad, and click OK.

Step 5 From within Wordpad, select Open from the File menu, and navigate to the newly copied C:\CiscoSystems\uOne\parms\DialMap.ini.

Step 6 Change the ToRegExp value for the [USDOMESTIC:OfficePBX5] section to reflect your 3-digit area code and 2-digit exchange---for example, ^80455([0-9]{5})$0$

Note The USDOMESTIC section of the DialMap.ini file is closely integrated with the dial mapping information in CallManager.

Step 7 Change the Return values for the [DialPlan:Rule1] section to your 3-digit area code and 2-digit exchange---for example, 80455$t0.

Step 8 Change the Return values for the [DialPlan:Rule2] section to your 3-digit area code---for example, 804$t0.

Step 9 Change the Return value for the [SKINNYCALLINGPARTY:5Digits] section to your 3-digit area code and 2-digit exchange---for example, 80455$f0.

Step 10 Change the Return value for the [SKINNYCALLEDPARTY:5Digits] section to your 3-digit area code and 2-digit exchange---for example, 80455$f0.

Step 11 In the [SKINNYCALLTYPE:VoiceMail] section, change the value in FromRegExp to include the pilot number for voice mail for your system---for example, ^(52501)$0$.

Step 12 In the [SKINNYCALLTYPE:Forwarded] section, change Constraint to include the pilot number for your system---for example, ($f0 != 52501).

Step 13 In the [MWI:5Digits] section, change the FromRegExp value to reflect your 3-digit area code and 2-digit exchange---for example, ^80455([0-9]{5})$0$.

Step 14 Save and close the file.

The following are example sections which you need to edit for the 5-digit dialing plan.

Restarting the uOne Services

After setting the .ini file information, restart the uOne services as follows.

Completing the Configuration

After the uOne .ini files have been set up, the CallManager Administration must be configured to correlate with the uOne .ini settings. See the "Configuring CallManager" chapter of this guide to set up CallManager.

Posted: Mon Jul 10 13:11:33 PDT 2000
Copyright 1989-2000©Cisco Systems Inc.