Table of Contents
Preface
This section discusses the intended audience and organization of this Cisco ICS 7750 Hardware Installation Guide and defines the conventions used to convey instructions and information.
This guide is for installers and operators of the Cisco Integrated Communications System 7750 (referred to from this point on as the Cisco ICS 7750 or the system). This guide is intended primarily for the following audiences:
- Customers with some experience installing telephone or internetworking equipment.
- System administrators who are responsible for installing, operating, and maintaining internetworking and telephony equipment
This guide is organized as follows:
- "Cisco ICS 7750 Product Overview," briefly describes the product and its hardware components.
- "Preparing for Installation," describes actions you must take and concepts you should understand before installing the system.
- "Installing the Cisco ICS 7750," describes how to mount the system and connect cables to the individual subsystem components, which come preinstalled in the chassis. It also describes how to remove and install the subsystem cards, power modules, and fan trays.
- "Cisco ICS 7750 Power Information," describes how to cable the system for power and includes power-reference information for the system.
- "Cisco ICS 7750 Processor Cards," describes each subsystem card in detail, including descriptions of the front-panel connectors and LEDs.
- "Technical Specifications," includes technical specifications for the system.
- "System Power Consumption," includes power consumption information for the system, based on installed components.
- "Cable and Connector Pinouts," includes cable and connector pinouts for the system.
This guide uses the following conventions for instructions and information.
Notes, cautions, and warnings use the following conventions and symbols:
 |
Caution This caution symbol means reader be careful. In this situation, you might do something that could result in equipment damage or loss of data.
 |
Warning This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. To see translations of the warnings that appear in this publication, refer to the Regulatory Compliance and Safety Information document that accompanied this device. |
|
Waarschuwing
| Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij7 elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van standaard maatregelen om ongelukken te voorkomen. Voor vertalingen van de waarschuwingen die in deze publicatie verschijnen, kunt u het document Regulatory Compliance and Safety Information (Informatie over naleving van veiligheids- en andere voorschriften) raadplegen dat bij dit toestel is ingesloten.
|
Varoitus
| Tämä varoitusmerkki merkitsee vaaraa. Olet tilanteessa, joka voi johtaa ruumiinvammaan. Ennen kuin työskentelet minkään laitteiston parissa, ota selvää sähkökytkentöihin liittyvistä vaaroista ja tavanomaisista onnettomuuksien ehkäisykeinoista. Tässä julkaisussa esiintyvien varoitusten käännökset löydät laitteen mukana olevasta Regulatory Compliance and Safety Information -kirjasesta (määräysten noudattaminen ja tietoa turvallisuudesta).
|
Attention
| Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant causer des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers posés par les circuits électriques et familiarisez-vous avec les procédures couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions d'avertissements figurant dans cette publication, consultez le document Regulatory Compliance and Safety Information (Conformité aux règlements et consignes de sécurité) qui accompagne cet appareil.
|
Warnung
| Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu einer Körperverletzung führen könnte. Bevor Sie mit der Arbeit an irgendeinem Gerät beginnen, seien Sie sich der mit elektrischen Stromkreisen verbundenen Gefahren und der Standardpraktiken zur Vermeidung von Unfällen bewußt. Übersetzungen der in dieser Veröffentlichung enthaltenen Warnhinweise finden Sie im Dokument Regulatory Compliance and Safety Information (Informationen zu behördlichen Vorschriften und Sicherheit), das zusammen mit diesem Gerät geliefert wurde.
|
Avvertenza
| Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di lavorare su qualsiasi apparecchiatura, occorre conoscere i pericoli relativi ai circuiti elettrici ed essere al corrente delle pratiche standard per la prevenzione di incidenti. La traduzione delle avvertenze riportate in questa pubblicazione si trova nel documento Regulatory Compliance and Safety Information (Conformità alle norme e informazioni sulla sicurezza) che accompagna questo dispositivo.
|
Advarsel
| Dette varselsymbolet betyr fare. Du befinner deg i en situasjon som kan føre til personskade. Før du utfører arbeid på utstyr, må du vare oppmerksom på de faremomentene som elektriske kretser innebærer, samt gjøre deg kjent med vanlig praksis når det gjelder å unngå ulykker. Hvis du vil se oversettelser av de advarslene som finnes i denne publikasjonen, kan du se i dokumentet Regulatory Compliance and Safety Information (Overholdelse av forskrifter og sikkerhetsinformasjon) som ble levert med denne enheten.
|
Aviso
| Este símbolo de aviso indica perigo. Encontra-se numa situação que lhe poderá causar danos físicos. Antes de começar a trabalhar com qualquer equipamento, familiarize-se com os perigos relacionados com circuitos eléctricos, e com quaisquer práticas comuns que possam prevenir possíveis acidentes. Para ver as traduções dos avisos que constam desta publicação, consulte o documento Regulatory Compliance and Safety Information (Informação de Segurança e Disposições Reguladoras) que acompanha este dispositivo.
|
¡Advertencia!
| Este símbolo de aviso significa peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considerar los riesgos que entraña la corriente eléctrica y familiarizarse con los procedimientos estándar de prevención de accidentes. Para ver una traducción de las advertencias que aparecen en esta publicación, consultar el documento titulado Regulatory Compliance and Safety Information (Información sobre seguridad y conformidad con las disposiciones reglamentarias) que se acompaña con este dispositivo.
|
Varning!
| Denna varningssymbol signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanligt förfarande för att förebygga skador. Se förklaringar av de varningar som förkommer i denna publikation i dokumentet Regulatory Compliance and Safety Information (Efterrättelse av föreskrifter och säkerhetsinformation), vilket medföljer denna anordning.
|
|
This section describes other publications in the Cisco ICS 7750 documentation set as well as related Cisco publications.
The following publications are companion documents to this guide and comprise the Cisco ICS 7750 documentation set:
- For guidelines on how to set up your site for data and voice networking, refer to the Cisco ICS 7750 Site and Network Design Guide.
- For Cisco ICS 7700 System Manager software setup and usage, refer to the Cisco ICS 7750 Getting Started Guide and the Cisco ICS 7700 System Manager User Guide.
- For Cisco ICS 7750 software configuration with IOS, refer to the Cisco ICS 7750 Software Configuration Guide.
- For a list of IOS commands that are new or specific to the Cisco ICS 7750, refer to the Cisco ICS 7750 Command Reference.
- For system administration and troubleshooting, refer to the Cisco ICS 7750 Administration and Troubleshooting Guide.
- For international agency compliance, safety, and statutory information for interfaces, refer to Regulatory Compliance and Safety Information for the Cisco ICS 7750.
For information about the backup power supply options supported by the Cisco ICS 7750, refer to the following publications:
- Cisco Redundant Power System 300 Hardware Installation Guide
- User's Manual APC Smart-UPS
For information about voice interface card (VIC), WAN interface card (WIC), and VWIC installation, cabling, and configuration, refer to the Cisco WAN Interface Card Hardware Installation Guide.
For information about Cisco CallManager, refer to the following publications:
- Cisco CallManager Administration Guide
- Configuration Notes for Cisco CallManager Release 3.0
- Cisco CallManager v3.0 Remote Serviceability Users Guide
For information about the Catalyst 3500 series XL switches, including the Catalyst 3524-PWR XL switch, refer to the following publications:
- Quick Start Guide: Catalyst 3500 Series XL Switches
- Catalyst 3500 Series XL Hardware Installation Guide
- Catalyst GigaStack Gigabit Interface Converter Installation Guide
- Cisco IOS Desktop Switching Software Configuration Guide: Catalyst
2900 Series XL and Catalyst 3500 Series XL Cisco IOS 12.0(5)XU
- Cisco IOS Desktop Switching Command Reference (online only)
For information about Cisco IP Phones, refer to the following publications:
- Getting Started with the Cisco IP Phone 7960
- Installing the Wall Mount Kit for the Cisco IP Phone
- Cisco IP Phone Administration Guide
The Cisco IOS software documentation set describes the tasks and commands necessary to configure certain system components, as well as other Cisco products such as access servers, routers, and switches. Each configuration guide can be used in conjunction with its corresponding command reference. The IOS software document set is available online. For more information about online documents, refer to the "Cisco Connection Online" section later in this Preface.
The following document set supports IOS software:
- Cisco IOS Software Command Summary
- Cisco IOS System Error Messages
- Debug Command Reference
- Dial Solutions Quick Configuration Guide
For information about CiscoWorks2000, which includes CiscoWorks2000 Server, CiscoWorks Switched Internet (CWSI) Campus, Resource Manager Essentials, and CiscoView, refer to the following publications:
- Getting Started with CiscoView
- Getting Started with the CiscoWorks2000 Server
- Getting Started with CWSI Campus
- Installing Resource Manager Essentials/CWSI Campus on Windows
- Using the Campus TrafficDirector Application
- Using the Campus UserTracking Application
- Using the Campus VlanDirector Application
- Using CiscoView
- Using Resource Manager Essentials
You can access the most current Cisco documentation on the World Wide Web at http://www.cisco.com, http://www-china.cisco.com, or http://www-europe.cisco.com.
Cisco documentation and additional literature are available in a CD-ROM package, which ships with your product. The Documentation CD-ROM is updated monthly. Therefore, it is probably more current than printed documentation. The CD-ROM package is available as a single unit or as an annual subscription.
Registered CCO users can order the Documentation CD-ROM and other Cisco Product documentation through our online Subscription Services at http://www.cisco.com/cgi-bin/subcat/kaojump.cgi.
Nonregistered CCO users can order documentation through a local account representative by calling Cisco's corporate headquarters (California, USA) at 408 526-4000 or, in North America, call 800 553-NETS (6387).
Cisco provides Cisco Connection Online (CCO) as a starting point for all technical assistance. Warranty or maintenance contract customers can use the Technical Assistance Center. All customers can submit technical feedback on Cisco documentation using the web, e-mail, a self-addressed stamped response card included in many printed docs, or by sending mail to Cisco.
Cisco continues to revolutionize how business is done on the Internet. Cisco Connection Online is the foundation of a suite of interactive, networked services that provides immediate, open access to Cisco information and resources at anytime, from anywhere in the world. This highly integrated Internet application is a powerful, easy-to-use tool for doing business with Cisco.
CCO's broad range of features and services helps customers and partners to streamline business processes and improve productivity. Through CCO, you will find information about Cisco and our networking solutions, services, and programs. In addition, you can resolve technical issues with online support services, download and test software packages, and order Cisco learning materials and merchandise. Valuable online skill assessment, training, and certification programs are also available.
Customers and partners can self-register on CCO to obtain additional personalized information and services. Registered users may order products, check on the status of an order and view benefits specific to their relationships with Cisco.
You can access CCO in the following ways:
- WWW: www.cisco.com
- Telnet: cco.cisco.com
- Modem using standard connection rates and the following terminal settings: VT100 emulation; 8 data bits; no parity; and 1 stop bit.
- From North America, call 408 526-8070
- From Europe, call 33 1 64 46 40 82
You can e-mail questions about using CCO to cco-team@cisco.com.
The Cisco Technical Assistance Center (TAC) is available to warranty or maintenance contract customers who need technical assistance with a Cisco product that is under warranty or covered by a maintenance contract.
To display the TAC web site that includes links to technical support information and software upgrades and for requesting TAC support, use www.cisco.com/techsupport.
To contact by e-mail, use one of the following:
Language
| E-mail Address
|
|---|
English
| tac@cisco.com
|
Hanzi (Chinese)
| chinese-tac@cisco.com
|
Kanji (Japanese)
| japan-tac@cisco.com
|
Hangul (Korean)
| korea-tac@cisco.com
|
Spanish
| tac@cisco.com
|
Thai
| thai-tac@cisco.com
|
In North America, TAC can be reached at 800 553-2447 or 408 526-7209. For other telephone numbers and TAC e-mail addresses worldwide, consult the following web site: http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml.
If you are reading Cisco product documentation on the World Wide Web, you can submit technical comments electronically. Click Feedback in the toolbar and select Documentation. After you complete the form, click Submit to send it to Cisco.
You can e-mail your comments to bug-doc@cisco.com.
To submit your comments by mail, for your convenience many documents contain a response card behind the front cover. Otherwise, you can mail your comments to the following address:
Cisco Systems, Inc.
Document Resource Connection
170 West Tasman Drive
San Jose, CA 95134-9883
We appreciate and value your comments.
Posted: Mon Oct 2 13:28:30 PDT 2000
Copyright 1989-2000©Cisco Systems Inc.
