|
|
The configuration messages are the most generic group of messages and can be written by any task group as well as the Trace and IUCV address spaces. Any message that can be written by any IJT-level parsing routines are in this group. These include messages T00CF000 through T00CF999.
This section describes messages T00CF000 through T00CF999.
Explanation The configuration member contains an invalid statement. Initialization of APP task group or LU pool failed.
| mem_name | Name of the configuration member. |
| cmnd_num | Logical statement number. |
| cmnd_name | Invalid statement. |
Recommended Action Remove the statement command from the configuration parameters and restart the APP task group. If the problem was LU pool related, correct the invalid statement, then issue an REFRESH LUPARM(mem_name) command from the console.
Explanation The configuration member contains an invalid parameter.
Recommended Action Remove the statement command from the configuration parameters and restart the APP task group. If the problem was LU pool related, correct the invalid statement, then issue an REFRESH LUPARM(mem_name) command from the console.
Explanation During initialization of the LU pool facility, the LU pool configuration member (mem_name) was not specified correctly. This message displays when the startup command script does not correctly identify the APPCFGxx or APPLUPxx configuration files, or the REFRESH LUPARM(mem_name) operator command incorrectly specifies the member name.
Recommended Action Correctly specify the APPCFGxx and APPLUPxx configuration files and reinitialize the APP task group or issue the REFRESH LUPARM(mem_name) command with the correct APPLUPxx member.
Explanation A syntax error was encountered with an APPLUPxx command statement. The LU pool facility is not activated.
| kywd | Keyword in error. |
| mem_name | Member name. |
| cmnd_num | Logical number of the statement. |
| cmnd_name | Statement containing the syntax error. |
Recommended Action Correct the statement and issue the REFRESH LUPARM(mem_name) command from the operator console.
Explanation A syntax error was encountered in an LU pool configuration statement. The LU pool facility is not activated.
| kywd | Keyword in error. |
| mem_name | Member name. |
| cmnd_num | Logical number of the statement. |
| cmnd_name | Statement containing the error. |
Recommended Action Eliminate the conflicting keyword specification and issue the REFRESH LUPARM(mem_name) command from the operator console.
Explanation An improper value was coded in a keyword of a statement. This error message is usually preceded by another message with more details.
| kywd | Specified keyword. |
| stmt | Specified statement. |
Recommended Action Correct the value in the configuration parameters and restart the APP task group.
Explanation The keyword entered was not a valid decimal data. It must be between 0 and 9, inclusive.
Explanation A keyword was coded with a value that did not match a list of expected values.
| value | Coded value. |
| kywd | Specified keyword. |
Recommended Action Correct the value in the configuration parameters and restart the APP task group.
Explanation The TSO parser detected a syntax error while processing a statement. This message is followed by message T00CF038E describing which statement is in error.
| mem_name | Member name. |
| cmnd_name | Failing command statement. |
| rec_num | Logical record number of the statement containing the error. |
Recommended Action Read the Cisco IOS for S/390 Customization Guide for more information about parsing. Correct the value in the configuration parameters and restart the APP task group.
Explanation The specified value is out of range.
Recommended Action Correct the specified value and retry.
Explanation The named driver has been added for named device.
Explanation Value of subparm parameter is invalid or out of range.
Recommended Action Correct the value and restart.
Explanation A value was specified that was too large. It was reduced to a lower value.
| stmnt | Statement. |
| kywd | Keyword. |
| value | Value specified. |
| max_value | Maximum value allowed. |
Recommended Action To avoid a recurrence of this message, correct the value in the configuration parameters and restart the APP task group.
Explanation A value was specified that was too small. It was increased to higher value.
| stmnt | Statement. |
| kywd | Keyword. |
| value | Value specified. |
| min_value | Minimum value allowed. |
Recommended Action To avoid a recurrence of this message, correct the value in the configuration parameters and restart the APP task group.
Explanation The TSO parser detected an unidentified keyword. This message is followed by message T00CF038E.
| mem_name | Name of the configuration member. |
| cmnd_name | Command statement. |
| kywd | Unidentified keyword. |
| rec_num | Record number of the configuration statement that contains the error |
Recommended Action Correct the value in the configuration parameters and restart the APP task group.
Explanation This message always follows message T00CF018E or T00CF036E. It displays the parameter and value (up to 80 characters) of the configuration statement causing the error.
Recommended Action Take corrective action specified in the associated T00CF018E or T00CF036E message.
Explanation An unexpected error was detected in the configuration file I/O handler. The code is the error/return code.
Recommended Action Report this error to the Cisco IOS for S/390 administrator.
Explanation The parameter text in a statement exceeds 65,586 characters. All further configuration statement processing is halted.
| stmnt | Specified statement. |
| mem_rec_num | Configuration member record number. |
| mem_name | Configuration member. |
Recommended Action Correct the value in the configuration parameters and restart the APP task group.
Explanation Keyword kywd value class is invalid. The previous value oclass will be used.
Explanation Keyword kywd of statement stmnt contains invalid subfield of field.
Explanation The component specified by component is unknown in the LOGGING statement.
|
|