|
|
This chapter explains the function and syntax of the switching commands from show lane config through show mpoa client cache. For more information about defaults and usage guidelines, see the corresponding chapter of the Cisco IOS Switching Command Reference, Release 12.1.
To display global LANE information for the configuration server configured on an interface, use the show lane config command in EXEC mode.
AIP on the Cisco 7500 Series Routers; for the ATM Port Adapter on the Cisco 7200 Series
show lane config [interface atm slot/0]
ATM Port Adapter on the Cisco 7500 Series Routers
show lane config [interface atm slot/port-adapter/0]
Cisco 4500 and 4700 Routers
show lane config [interface atm number]
Syntax Description
interface atm slot/0 (Optional) ATM interface slot and port for the following: interface atm slot/port-adapter/0 (Optional) ATM interface slot, port adapter, and port number for the ATM port adapter on the Cisco 7500 series routers. interface atm number (Optional) ATM interface number for the NPM on the Cisco 4500 or 4700 routers.
To display the configuration server's database, use the show lane database command in EXEC mode.
show lane database [database-name]
Syntax Description
database-name (Optional) Specific database name.
To display the automatically assigned ATM address of each LANE component in a router or on a specified interface or subinterface, use the show lane default-atm-addresses command in EXEC mode.
AIP on the Cisco 7500 series routers; for the ATM port adapter on the Cisco 7200 series
show lane default-atm-addresses [interface atm slot/port.subinterface-number]
ATM port adapter on the Cisco 7500 series routers
show lane default-atm-addresses [interface atm slot/port-adapter/port.subinterface-number]
Cisco 4500 and 4700 routers
show lane default-atm-addresses [interface atm number.subinterface-number]
Syntax Description
interface atm slot/port (Optional) ATM interface slot and port for the following: interface atm slot/port-adapter/port (Optional) ATM interface slot, port adapter, and port number for the ATM port adapter on the Cisco 7500 series routers. interface atm number (Optional) ATM interface number for the NPM on the Cisco 4500 or 4700 routers. .subinterface-number (Optional) Subinterface number.
To display the LANE ARP table of the LANE client configured on an interface or any of its subinterfaces, on a specified subinterface, or on an emulated LAN, use the show lane le-arp command in EXEC mode.
AIP on the Cisco 7500 series routers; for the ATM port adapter on the Cisco 7200 series
show lane le-arp [interface atm slot/port[.subinterface-number] | name elan-name]
ATM port adapter on the Cisco 7500 series routers
show lane le-arp [interface atm slot/port-adapter/port[.subinterface-number] | name elan-name]
Cisco 4500 and 4700 routers
show lane le-arp [interface atm number[.subinterface-number] | name elan-name]
Syntax Description
interface atm slot/port (Optional) ATM interface slot and port for the following: interface atm slot/port-adapter/port (Optional) ATM interface slot, port adapter, and port number for the ATM port adapter on the Cisco 7500 series routers. interface atm number (Optional) ATM interface number for the NPM on the Cisco 4500 or 4700 routers. .subinterface-number (Optional) Subinterface number. name elan-name (Optional) Name of emulated LAN. The maximum length of the name is 32 characters.
To display global information for the LANE server configured on an interface, on any of its subinterfaces, on a specified subinterface, or on an emulated LAN, use the show lane server command in EXEC mode.
AIP on the Cisco 7500 series routers; for the ATM port adapter on the Cisco 7200 series
show lane server [interface atm slot/port[.subinterface-number] | name elan-name] [brief]
ATM port adapter on the Cisco 7500 series routers
show lane server [interface atm slot/port-adapter/port[.subinterface-number] | name elan-name] [brief]
Cisco 4500 and 4700 routers
show lane server [interface atm number[.subinterface-number] | name elan-name] [brief]
Syntax Description
interface atm slot/port (Optional) ATM interface slot and port for the following: interface atm slot/port-adapter/port (Optional) ATM interface slot, port adapter, and port number for the ATM port adapter on the Cisco 7500 series routers. interface atm number (Optional) ATM interface number for the NPM on the Cisco 4500 or 4700 routers. .subinterface-number (Optional) Subinterface number. name elan-name (Optional) Name of emulated LAN. The maximum length of the name is 32 characters. brief (Optional) Keyword used to display the brief subset of available information.
To display MLS details, including specifics for MLSP, use the show mls rp command in EXEC mode.
show mls rp [interface]
Syntax Description
interface (Optional) Displays information for one interface. Without this argument, detailed view of all interfaces are displayed.
To display IPX Multilayer Switching (MLS) details for the route processor, including specific information about the Multilayer Switching Protocol (MLSP), use the show mls rp interface command in privileged EXEC mode.
show mls rp interface type number
Syntax Description
type Interface type. number Interface number.
To display hardware-switched multicast flow information about IP multicast Multilayer Switching (MLS), use the show mls rp ip multicast command in EXEC mode.
show mls rp ip multicast [locate] [group [source] [vlan-id ]] | [statistics] | [summary]
Syntax Description
locate (Optional) Displays flow information associated with the switch. This keyword applies only to a single router and multiple switches. group (Optional) Address of the IP multicast group about which to display information. source (Optional) IP multicast source sending to the specified multicast group about which to display information. vlan-id (Optional) Source VLAN about which to display information. statistics (Optional) Displays MLS statistics. summary (Optional) Displays MLS summary.
To display details for all IPX Multilayer Switching (MLS) interfaces on the IPX MLS router, use the show mls rp ipx command in privileged EXEC mode.
show mls rp ipxSyntax Description
This command has no arguments or keywords.
To display IPX Multilayer Switching (MLS) interfaces for a specific Virtual Trunk Protocol (VTP) domain on the route processor, use the show mls rp vtp-domain command in privileged EXEC mode.
show mls rp vtp-domain domain-name
Syntax Description
domain-name The name of the Virtual Trunk Protocol (VTP) domain whose MLS interfaces will be displayed.
Syntax Description
This command has no arguments or keywords.
To show which tunnels have been admitted locally, and their parameters (such as priority, bandwidth, incoming and outgoing interface, and state), use the show mpls traffic-eng link-management admission-control command in EXEC mode.
show mpls traffic-eng link-management admission-control [interface name]
Syntax Description
interface name (Optional) Shows only those tunnels that are admitted on the specified interface.
To show local link information currently being flooded by MPLS traffic engineering link management into the global traffic engineering topology, use the show mpls traffic-eng link-management advertisements command in EXEC mode.
show mpls traffic-eng link-management advertisementsSyntax Description
This command has no arguments or keywords.
To show current local link information, use the show mpls traffic-eng link-management bandwidth-allocation command in EXEC mode.
show mpls traffic-eng link-management bandwidth-allocation [interface name]
Syntax Description
interface name (Optional) Shows only those tunnels that have been admitted on the specified interface.
To show IGP neighbors, use the show mpls traffic-eng link-management igp-neighbors command in privileged EXEC mode.
show mpls traffic-eng link-management igp-neighbors [{igp-id {isis isis-address | ospf ospf-id} | ip A.B.C.D}]
Syntax Description
igp-id Shows the IGP neighbors using a specified IGP identification. isis isis-address Specifies an IS-IS neighbor to display when displaying neighbors by IGP ID. ospf ospf-id Specifies an OSPF neighbor to display when displaying neighbors by IGP ID. ip A.B.C.D. Shows the IGP neighbors using a specified IGP IP address.
To show per-interface resource and configuration information, use the show mpls traffic-eng link-management interfaces command in EXEC mode.
show mpls traffic-eng link-management interfaces [interface]
Syntax Description
interface (Optional) Specifies the name of a single interface for which information is to be displayed.
To show summary of link management information, use the show mpls traffic-eng link-management summary command in EXEC mode.
show mpls traffic-eng link-management summary [interface name]
Syntax Description
interface name (Optional) Specifies the name of a single interface for which information is to be displayed.
To show the MPLS traffic engineering global topology as currently known at this node, use the show mpls traffic-eng topology command in privileged EXEC mode.
show mpls traffic-eng topology [{A.B.C.D | igp-id {isis nsapaddr | ospf A.B.C.D}] [brief]
Syntax Description
A.B.C.D Specifies the node by the IP address (router identifier to interface address). igp-id Specifies the node by IGP router identifier. isis nsapaddr Specifies the node by router identification (nsapaddr) if using IS-IS. ospf A.B.C.D Specifies the node by router identifier if using OSPF. brief (Optional) The brief form of the output gives a less detailed version of the topology.
To show information about tunnels, use the show mpls traffic-eng tunnel command in EXEC mode.
show mpls traffic-eng tunnel [{tunnel_interface | destination address | source-id [{ipaddress | 0-MAX | name name role {all | head | middle | tail | remote} | {up | down}}] [brief]
Syntax Description
tunnel_interface (Optional) Shows tunnel interface. destination address (Optional) Displays brief summary of tunnel status and configuration. source-id ipaddress (Optional) Restricts the display to tunnels originating at that IP address. 0-MAX (Optional) name name (Optional) Restricts the display to tunnels with that value as their name. The tunnel name is derived from the interface description, if specified; otherwise, it is the interface name. The tunnel name is included in the signaling message so it is available at all hops. role (Optional) Restrict the display to tunnels with the indicated role. all (Optional) Displays all tunnels. head (Optional) Displays tunnels with their head at this router. middle (Optional) Displays tunnels with a midpoint at this router. tail (Optional) Displays tunnels with a tail at this router. remote (Optional) Displays tunnels with their head at some other router---the combination of middle and tail. up (Optional) Restricts the display to tunnels that are up. When you specify "up," a tunnel head is shown if the tunnel interface is up. Tunnel midpoints and tails are typically either up or not present. down (Optional) Restricts the display to tunnels that are down. brief (Optional) Specifies a format with one line per tunnel.
To show summary information about tunnels, use the show mpls traffic-eng tunnel summary command in privileged EXEC.
show mpls traffic-eng tunnel summarySyntax Description
This command has no arguments or keywords.
To display a summary of information regarding one or all MPCs, use the show mpoa client command in EXEC mode.
show mpoa client [name mpc-name] [brief]
Syntax Description
name mpc-name (Optional) Name of the MPC with the specified name. brief (Optional) Output limit of the command.
To display the ingress or egress cache entries matching the IP addresses for the MPCs, use the show mpoa client cache command in EXEC mode.
show mpoa client [name mpc-name] cache [ingress | egress] [ip-address ip-address]
Syntax Description
name mpc-name (Optional) Name of the MPC with the specified name. ingress (Optional) Displays ingress cache entries associated with an MPC. egress (Optional) Displays egress cache entries associated with an MPC. ip-address ip-address (Optional) Displays cache entries that match the specified IP address.
Posted: Wed Jul 26 13:17:09 PDT 2000
Copyright 1989-2000©Cisco Systems Inc.