Table of Contents

Contents
Introduction

Cisco AS5800/Voice Gateway

Cisco AS5800 Voice Feature Card

System Requirements

Memory Recommendations
Hardware Supported
Determining the Software Version
Upgrading to a New Software Release
Microcode and Modem Code Software
Feature Set Tables

New and Changed Information

New Hardware Features in Cisco IOS Release 12.1(3) T

AS58-324UPC-CC

New Software Features in Cisco IOS Release 12.1(3) T

AAA Session MIB
Circuit Interface Identification MIB
Cisco AAA Server MIB and Additional Enhancements for the Cisco AS5300 and Cisco AS5800
Event MIB
Fax Relay Packet Loss Concealment
Individual SNMP Trap Support
Monitoring Resource Availability on Cisco AS5300 Universal Access Servers
Network Side ISDN PRI Signaling, Trunking, and Switching
Preauthentication with ISDN PRI and Channel-Associated Signaling
TCP Clear Performance Optimization

New Hardware Features in Cisco IOS Release 12.1(2)T
New Software Features in Cisco IOS Release 12.1(2)T

AAA Server Group Deadtimer (CSCdp13160)
Preauthentication with ISDN PRI (CSCdm82434)

New Hardware Features in Cisco IOS Release 12.1(1) T
New Software Features in Cisco IOS Release 12.1(1) T

Cisco H.323 Version 2 Phase 2

Limitations and Restrictions

MIBs

Caveats
Related Documentation

Release-Specific Documents
Platform-Specific Documents
Feature Modules
Cisco IOS Software Documentation Set

Documentation Modules
Cisco IOS Release 12.1 Documentation Set

Obtaining Documentation

World Wide Web
Documentation CD-ROM
Ordering Documentation

Obtaining Technical Assistance

Cisco Connection Online
Technical Assistance Center
Software Configuration Tips on the Cisco Technical Assistance Center Home Page
Documentation Feedback

Release Notes for Cisco AS5800 Universal Access Servers for Cisco IOS Release 12.1 T

July 24, 2000

Note   You can find the most current Cisco IOS documentation on Cisco Connection Online (CCO ). These electronic documents may contain updates and modifications made after the hardcopy documents were printed.

These release notes for the Cisco AS5800 universal access servers describe the enhancements provided in Cisco IOS Release 12.1(3) T. These release notes are updated as needed.

For a list of the software caveats that apply to Cisco IOS Release 12.1 T, see Caveats for Cisco  IOS Release  that accompanies these release notes. The caveats document is updated for every maintenance release and is located on Cisco Connection Online (CCO)  and the Documentation CD-ROM.

Use these release notes with Cross-Platform Release Notes for Cisco  IOS Release  on CCO  and the Documentation CD-ROM.

Contents

These release notes describe the following topics:

• Introduction

• System Requirements

• New and Changed Information

• Limitations and Restrictions

• Caveats

• Related Documentation

• Obtaining Documentation

• Obtaining Technical Assistance

Introduction

The Cisco AS5800 is a high-density, Integrated Services Digital Network (ISDN) and modem Wide Area Network (WAN) aggregation system that provides digital and analog call termination. It is intended to be used as a service provider dial point-of-presence (POP) or centralized enterprise dial gateway. The Cisco AS5800 consists of a dial shelf, a router shelf, and (optionally) a system controller:

• The Cisco DS5814 (dial shelf) has 14 slots and can support 1 or 2 dial shelf controller cards and up to 12 feature cards to provide full analog modem and ISDN coverage. The dial shelf supports up to 2047 simultaneous analog and/or digital calls. Analog calls are terminated by a feature card that is loaded with integrated modems. ISDN calls are terminated onboard the trunk card on High-Level Data Link Control (HDLC) controllers. The E1 trunk, CT3 trunk, and the T1 trunk cards include channel service units (CSUs) and have either 12 E1 ports or 12 T1 ports that can operate as Primary Rate Interface (PRI) interfaces or channelized interfaces in any combination. The CT3 trunk supports 28 T1s. The specific trunk card limitations are described in Table 2, Part 1.

---

Note   T1 and E1 cards are not supported in the same box.

---

• The Cisco RS7206VXR (router shelf) contains a network processing engine, an I/O controller, and the egress interfaces, such as High-Speed Serial Interface (HSSI), Fast Ethernet (FE), Fiber Distributed Data Interface (FDDI), and Asynchronous Transfer Mode (ATM), and supports either 280W AC-input or 280W DC-input redundant power. The router shelf also may contain one or two dial shelf interconnect port adapters each with a single RJ-45 receptacle, which is used to connect the router shelf to the Cisco 5814 dial shelf. The interconnect port adapter connects directly to the dial shelf controller card on the dial shelf via a Cisco-proprietary cable, customized with jack screws to secure the connection. You must use this specially designed cable that ships with your interconnect port adapter.

• The Cisco SC3640 (system controller) includes the Cisco 3640 router running Cisco IOS system controller software. The system controller can be installed at a remote facility so users can access multiple systems through a console port or Web interface. System administrators can download software configurations to any Cisco AS5800 universal access server using Simple Network Management Protocol (SNMP) or Telnet. The system controller monitors Cisco equipment to provide performance data collection, accounting data collection, and logging.

The AC-input power shelf is an optional component of the Cisco AS5800 and is used to convert AC-input power into DC-output power for the DC-powered Cisco 5814 dial shelf. The AC-input power shelf contains two AC-input power supplies.

The AC-input to DC-output connection supplies -48V DC-output power to the dial shelf power entry modules (PEMs). The PEMs receive the -48V and transmit power to the filter module. Power flows through the filter module to the backplane where it is distributed to the dial shelf controller card(s) and feature cards.

The AC-input power shelf includes two 2,000 W, AC-input power supplies that plug into a common power backplane in the AC-input power shelf. A single AC-input power supply is capable of powering a fully configured Cisco 5814 dial shelf. The second power supply provides full redundancy.

Cisco AS5800/Voice Gateway

The Cisco AS5800/Voice Gateway enables highly scalable deployment of toll-quality voice and fax services over data networks. Enhanced with Cisco's IOS software and Service Node (SN) capabilities, the Cisco AS5800 supports features such as prepaid and postpaid calling card, 800 call redirect, voice activated dialing, and voice and fax mail.

The Cisco AS5800 is specifically designed to meet the demands of large service providers such as Post, Telephone, and Telegraphs (PTTs), regional bell operating companies (RBOCs), inter-exchange carriers (IXCs), and large Internet telephony service providers (ITSPs). The physical architecture of the Cisco AS5800 product enhances reliability, availability, and serviceability. Critical features to dial POP administrators include minimizing downtime, service costs, and time to deployment.

The Cisco AS5800 supports up to 1344 voice ports in a single system, thus offering the highest concentration of VoIP Digital Signal Processors (DSPs) available in a single voice gateway. The Cisco AS5800 offers breakthrough voice quality, density, and scalability, while continuing to provide the rich set of access, VoIP, and QoS services that are part of Cisco IOS software.

Cisco AS5800 Voice Feature Card

The Cisco AS5800 Voice Feature card is a full featured voice processing card that supports 192 DSP-based voice ports. Voice processing capabilities include Voice Activity Detection (VAD), comfort noise generation, adaptive jitter buffering, programmable 16 and 32 msec echo cancellation, programmable frame size, and Dual Tone Multiple Frequency (DTMF) detection and generation. The Cisco AS5800 Voice Feature card offers industry-leading DSP density and a wide range of VoIP codecs, including G.711, G.729, G.729a, G.723.1, and Group III real-time fax support, on any port at any time.

For more information on the Cisco AS5800, refer to the Cisco AS5800 Universal Access Server Operations, Administration, Maintenance, and Provisioning Guide . 

For information on new features and Cisco IOS commands supported by Cisco IOS Release 12.1, see the "New and Changed Information" section and "Related Documentation" section.

System Requirements

This section describes the system requirements for Cisco IOS Release 12.1 T:

• Memory Recommendations

• Hardware Supported

• Determining the Software Version

• Upgrading to a New Software Release

• Microcode and Modem Code Software

• Feature Set Tables

Memory Recommendations

Table 1: Cisco AS5800 Memory Recommendations

System Components	Feature Set	Image Name	Software Image	Minimum Flash	Minimum DRAM
Cisco AS5800	IP Standard	IP Plus	c5800-p4-mz	16 MB	128 MB for NPE-200 256 MB for NPE-300
Dial Shelf: Cisco 5814		IP Plus	dsc-c5800-mz	8 MB	32 MB
Cisco AS5800	Service Provider Standard	Service Provider IPSec 56	c5800-p456i-mz	16 MB	128 MB for NPE-200 256 MB for NPE-300

Hardware Supported

Cisco IOS Release 12.1 T supports the Cisco AS5800:

• Cisco DS5814

• Cisco RS7206

• Cisco RS7206 VXR

For detailed descriptions of the new hardware features, see "New and Changed Information" section. Table 2 and Table 3 detail the supported interfaces, cards, options, NPE support, and port adapters.

Table 2, Part 1: Supported Hardware for the Cisco AS5800

Interfaces, Cards Options, and Support,	Description
Interfaces	12-port T1 or E1 termination card
	1- port channelized T3 (CT3) termination card
Modem Cards	72-port modem card (HMM)1
	144-port modem card (DMM)2
Voice Feature Cards (VFCs)	AS58-324UPC-CC
	192-port voice card (VOX)
	324-Port modem/UP card (see "AS58-324UPC-CC" section )
Optional AC-input Power Shelves	Two AC-input power supplies
NPE Support	With any Cisco AS5800 software image, the maximum hardware configuration with an NPE-200 router shelf (RS7206) is one CT3 or two T1/E1 trunk cards and five DMMs or 10 HMMs for a maximum of 28 T 1/24 E1 controllers and 720 modems. If a larger configuration is desired, a second NPE-200 router shelf can be configured in split-shelf mode, or a single NPE-300 (RS7206 VXR). The NPE call limitations for a Cisco AS5800/Voice Gateway are 672 data calls per NPE-200 and 1344 data calls per NPE-300.

172-port modem card requires 32M DRAM. 2144-port modem card requires 64M DRAM.

Table 2, Part 2: Supported Hardware for the Cisco AS5800

Router Shelf	Port Adapter	Description
RS7206 Router Shelf	PA-100VG	Single-Port 100 VG Port Adapter
	PA-12E/2FE	Dual-Wide Ethernet-switch Port Adapter
	PA-1C-E	1-Port ESCON Channel Port Adapter
	PA-2CE1/PRI-120	2-Port Channelized E1/PRI Port Adapter, 120 ohm
	PA-2CE1/PRI-75	2-Port Channelized E1/PRI Port Adapter, 75 ohm
	PA-2CT1/PRI	2-Port Channelized T1/PRI Port Adapter
	PA-2E3	2-Port E3 Serial Port Adapter with E3 DSU
	PA-2FEISL-FX	2-Port Fast Ethernet/ISL 100BaseTx Port Adapter
	PA-2FEISL-TX	2-Port Fast Ethernet/ISL 100BaseFx Port Adapter
	PA-2H	Port Adapter, 2-Port HSSI
	PA-4B-U	4-Port BRI Port Adapter, U Interface
	PA-4E	Port Adapter, 4-Port Ethernet,10BT
	PA-4R	Port Adapter, 4-Port Token Ring (Older Hermon Based)
	PA-4R-DTR	Port Adapter, 4-Port Token Ring (Hawkeye Based)
	PA-4R-FDX	Port Adapter, 4 Port Token Ring 4/16Mbps, Full Duplex
	PA-4T+	Port Adapter, 4-Port Serial,5IN1
	PA-5EFL	Port Adapter, 5-Port Ethernet,10FL
	PA-8B-S/T	8-Port BRI Port Adapter, S/T Interface
	PA-8E	Port Adapter, 8-Port Ethernet,10BT
	PA-8T-232	Port Adapter, 8-Port Serial,232
	PA-8T-V35	Port Adapter, 8-Port Serial,V.35
	PA-8T-X21	Port Adapter, 8-Port Serial,X.21
	PA-A1-OC3MM	1 Port ATM OC3 Multi-Mode Port Adapter
	PA-A1-OC3SM	1 Port ATM OC3 Single Mode Intermediate Reach Port Adapter
	PA-A2-4E1XC-E3ATM	CES Port Adapter E3/E1 120 ohms
	PA-A2-4E1XC-OC3SM	CES OC3 Port Adapter 4E1 Ports 120 ohms
	PA-A2-4T1C-OC3SM	ATM CES Port Adapter, 4T1 CES Ports and 1 OC3 ATM SM Port
	PA-A2-4T1C-T3ATM	ATM CES Port Adapter, 4T1 CES Ports and 1 T3 ATM Port
	PA-A3-E3	1-Port ATM Enhanced E3 Port Adapter
	PA-A3-OC3MM	1-Port ATM Enhanced OC3c/STM1 Multi-Mode
	PA-A3-OC3SMI	1-Port ATM Enhanced OC3c/STM1 Single Mode
	PA-A3-OC3SML	1-Port ATM Enhanced OC3c/STM1 Single Mode
	PA-A3-T3	1-Port ATM Enhanced DS3 Port Adapter
	PA-CT3/4T1	Channelized DS3 Port Adapter with 4 T1
	PA-E3	1 Port E3 Serial Port Adapter with E3 DSU
	PA-F/FD-MM	Port Adapter,1-Port FDDI Full Duplex Multi-Mode
RS7206 Router Shelf (Continued)	PA-F/FD-SM	Port Adapter,1-Port FDDI Full Duplex Single-Mode
	PA-FE-FX	Port Adapter,1-Port FE, 100FX
	PA-FE-TX	Port Adapter,1-Port FE,100TX
	PA-F-MM	Port Adapter,1-Port FDDI Multi-Mode
	PA-F-SM	Port Adapter,1-Port FDDI Single Mode
	PA-H	Port Adapter,1-Port HSSI
	PA-POS-OC3MM	1-Port Packet/SONET OC3c/STM1 Multi-Mode Port Adapter
	PA-POS-OC3SMI	1-Port Packet/SONET OC3c/STM1 Single Mode (IR) Port Adapter
	PA-POS-OC3SML	1-Port Packet/SONET OC3c/STM1 Single Mode (LR) Port Adapter
	PA-T3	1-Port T3 Serial Port Adapter with T3 DSUs
	PA-T3+	1-Port T3 Serial Port Adapter Enhanced
	SA-COMP/1	Service Adapter, Compression (64 VCs Stac)
	SA-COMP/4	Service Adapter, Compression (256 VCs Stac)
RS7206VXR Router Shelf	PA-100VG	Single Port 100VG Port Adapter
	PA-12E/2FE	Dual-Wide Ethernet-Switch Port Adapter
	PA-1C-E	1 Port ESCON Channel Port Adapter
	PA-2E3	2 Port E3 Serial Port Adapter with E3 DSU
	PA-2FEISL-FX	2 port Fast Ethernet/ISL 100BaseTx Port Adapter
	PA-2FEISL-TX	2 port Fast Ethernet/ISL 100BaseFx Port Adapter
	PA-2H	Port Adapter, 2-Port HSSI
	PA-4B-U	4 Port BRI Port Adapter, U Interface
	PA-4E	Port Adapter, 4-Port Ethernet,10BT
	PA-4R-DTR	Port Adapter, 4-Port Token Ring (Hawkeye Based)
	PA-4T+	Port Adapter, 4-Port Serial,5in1
	PA-5EFL	Port Adapter, 5-Port Ethernet,10FL
	PA-8B-S/T	8 Port BRI Port Adapter, S/T Interface
	PA-8E	Port Adapter, 8-Port Ethernet,10BT
	PA-8T-232	Port Adapter, 8-Port Serial,232
	PA-8T-V35	Port Adapter, 8-Port Serial,V.35
	PA-8T-X21	Port Adapter, 8-Port Serial,X.21
	PA-A1-OC3MM	1 Port ATM OC3 Multi-Mode Port Adapter
	PA-A1-OC3SM	1 Port ATM OC3 Single Mode Intermediate Reach Port Adapter
	PA-A2-4E1XC-E3ATM	CES Port Adapter E3/E1 120 ohms
	PA-A2-4E1XC-OC3SM	CES OC3 Port Adapter 4E1 Ports 120 ohms
	PA-A2-4T1C-OC3SM	ATM CES Port Adapter, 4T1 CES Ports and 1 OC3 ATM SM Port
	PA-A2-4T1C-T3ATM	ATM CES Port Adapter, 4T1 CES Ports and 1 T3 ATM Port
RS7206VXR Router Shelf (Continued)	PA-A3-E3	1-Port ATM Enhanced E3 Port Adapter
	PA-A3-OC3MM	1-Port ATM Enhanced OC3c/STM1 Multi-Mode
	PA-A3-OC3SMI	1-Port ATM Enhanced OC3c/STM1 Single Mode
	PA-A3-OC3SML	1-Port ATM Enhanced OC3c/STM1 Single Mode
	PA-A3-T3	1-Port ATM Enhanced DS3 Port Adapter
	PA-E3	1 Port E3 Serial Port Adapter with E3 DSU
	PA-FE-FX	Port Adapter, 1-Port FE, 100FX
	PA-FE-TX	Port Adapter, 1-Port FE,100TX
	PA-GE	One-Port Gigabit Ethernet PA for 7200VXR
	PA-H	Port Adapter, 1-Port HSSI
	PA-POS-OC3MM	1-Port Packet/SONET OC3c/STM1 Multi-Mode Port Adapter
	PA-POS-OC3SMI	1-Port Packet/SONET OC3c/STM1 Single Mode (IR) Port Adapter
	PA-POS-OC3SML	1-Port Packet/SONET OC3c/STM1 Single Mode (LR) Port Adapter
	PA-T3	1 Port T3 Serial Port Adapter with T3 DSUs
	PA-T3+	1 Port T3 Serial Port Adapter Enhanced

Determining the Software Version

To determine the version of Cisco IOS software running on your Cisco AS5800, log in to the Cisco AS5800 and enter the show version EXEC command:

router> show version
Cisco Internetwork Operating System Software 
IOS (tm) 12.1 T Software (c5800-p4-mz), Version 12.1(3) T, RELEASE SOFTWARE

Upgrading to a New Software Release

For general information about upgrading to a new software release, see Cisco  IOS Upgrade Ordering Instructions located at:

http://www.cisco.com/warp/public/cc/cisco/mkt/ios/prodlit/957_pp.htm

For specific information about upgrading AS5800 IOS software, modem and firmware upgrades, and split dial shelf, refer to the Provisioning chapter in the Cisco AS5800 Operations, Administration, Maintenance, and Provisioning Guide (OAM&P) at:

http://www.cisco.com/univercd/cc/td/doc/product/access/acs_serv/as5800/op/prov.htm

Microcode and Modem Code Software

Microcode software images are bundled with the system software image. Bundling eliminates the need to store separate microcode images. When the router starts, the system software unpacks the microcode software bundle and loads the proper software on all the interface processor boards. Table 3 lists the current microcode versions for the Cisco AS5800.

You could have received a later version of modem code than the one bundled with the Cisco IOS software. The modem code in Flash memory is mapped to the modems. Unless you fully understand how Cisco IOS software uses modem code, it is important to keep the factory configuration.

The modem code release notes are on CCO  and the Documentation CD-ROM.

On CCO  at:

Technical Documents: Documentation Home Page: Access Servers and Access Routers: Firmware and Portware Information

On the Documentation CD-ROM at:

Feature Set Tables

The Cisco IOS software is packaged in feature sets consisting of software images--depending on the platform. Each feature set contains a specific set of Cisco IOS features.

Caution Cisco IOS images with strong encryption (including, but not limited to 168-bit (3DES) data encryption feature sets) are subject to United States government export controls and have limited distribution. Strong encryption images to be installed outside the United States are likely to require an export license. Customer orders may be denied or subject to delay due to United States government regulations. When applicable, purchaser/user must obtain local import and use authorizations for all encryption strengths. Please contact your sales representative or distributor for more information, or send an e-mail to export@cisco.com.

Table 4 lists the features and feature sets supported by the Cisco AS5800 in Cisco IOS Release 12.1 T and uses the following conventions:

• Yes--The feature is supported in the software image.

• No--The feature is not supported in the software image.

Note   This feature set table might contain a selected list of features. This table might not be cumulative or list all the features in each image.

Table 4: Feature List by Feature Set for the Cisco AS5800

Features	In1	Software Images by Feature Set
		IP Plus	IPsec 56
New Features in 12.1(3)T
AAA Session MIB	(3)	Yes	Yes
Circuit Interface Identification MIB	(3)	Yes	Yes
Cisco AAA Server MIB and Additional Enhancements for the Cisco AS5300 and Cisco AS5800	(3)	Yes	Yes
Event MIB	(3)	Yes	Yes
Fax Relay Packet Loss Concealment	(3)	Yes	Yes
Individual SNMP Trap Support	(3)	Yes	Yes
Monitoring Resource Availability on Cisco AS5300 Universal Access Servers	(3)	Yes	Yes
Network Side ISDN PRI Signaling, Trunking and Switching	(3)	Yes	Yes
Preauthentication with ISDN PRI and Channel-Associated Signaling	(3)	Yes	Yes
TCP Clear Performance Optimization	(3)	Yes	Yes
Hardware
AS58-324UPC-CC	(3)	Yes	Yes
IP Routing
Asynchronous Serial Traffic over UDP		Yes	Yes
LAN Support
CLI String Search		Yes	Yes
Dynamic Multiple Encaps for Dial-In over ISDN		Yes	Yes
L2TP Dialout		Yes	Yes
Parse Bookmarks		Yes	Yes
SS7		Yes	Yes
Management
Dial Shelf Controller Redundancy		Yes	Yes
Process MIB		Yes	Yes
SNMP Version 3		Yes	Yes
Miscellaneous
Cisco IOS DHCP Server		Yes	Yes
OS_IFSS		Yes	Yes
Security
AAA Server Group Deadtimer	(2)	Yes	Yes
AAA Server Group Enhancements	(2)	Yes	Yes
Preauthentication with ISDN PRI	(2)	Yes	Yes
Resource Pool Management with Direct Remote Services		Yes	Yes
WAN Services
Layer 2 Tunneling Protocol (L2TP)		Yes	Yes

1The number in the "In" column indicates the Cisco IOS release when the interface was introduced. For example, (4) means an interface was introduced in Cisco IOS Release 12.1(4). If a cell in this column is empty, the interface was included in the initial base release.

New and Changed Information

The following sections list the new hardware and software features supported by the Cisco AS5800 for Cisco IOS Release 12.1 T.

New Hardware Features in Cisco IOS Release 12.1(3) T

The following new software features are supported by the Cisco AS5800 for Cisco IOS Release 12.1(3) T:

AS58-324UPC-CC

A universal port is a port that can carry the equivalent of one DS0 of network traffic. Network traffic can be a modem, voice, or fax connection.

The AS58-324UPC-CC uses NextPort hardware and firmware to provide universal ports for the Cisco AS5800, so the UPC is sometimes referred to as a NextPort module. These ports are grouped into SPEs. An SPE is a service processing element, supporting six universal ports. There are 54 SPEs per UPC, for a total of 324 ports per UPC. Each UPC also has a minimum of a 128 MB SDRAM card. Configuration, management, and troubleshooting of universal ports can be done at the UPC, SPE, and port level.

The Cisco AS5800 can be equipped with a maximum of seven UPCs with upgradable firmware.

Currently the UPC supports data traffic, and is universal port capable, depending on the software and platform. Each UPC plugs directly into the dial shelf backplane and has no external connections. Each UPC has three LEDs, which indicate card status.

The Cisco AS5800 is capable of terminating up to 2,047 port connections (slightly more than an OC3) when equipped with seven UPCs and three CT3 + 1 12T1 trunk cards. A split shelf configuration with a second router shelf and second dial shelf controller are required to achieve full capacity.

A single router and a standard configuration will support up to 1,344 port connections. Cisco IOS Release 12.1(3)T is required for the UPC. Unless your system shipped with UPCs installed, you will need to upgrade the Cisco IOS image on the dial shelf and router shelf or shelves.

New Software Features in Cisco IOS Release 12.1(3) T

The following new software features are supported by the Cisco AS5800 for Cisco IOS Release 12.1(3) T:

AAA Session MIB

Customers are demanding the ability to both monitor and terminate their authenticated client connections via SNMP. Furthermore, customers are requesting that the client data provided be directly related to the accounting information reported by AAA to either Radius or Tacacs. Moreover, additional real-time information such as idle times are also requested for this feature in order to provide the ability to terminate calls with no activity present.

This feature allows Cisco's customers to extend and expand their ability to monitor end users by providing access to some client data objects via SNMP.

Circuit Interface Identification MIB

The Circuit Interface MIB consists of a single table, with each row being a sequence of two objects: Circuit Interface Description (cciDescr) and Circuit Interface Status (cciStatus). The cciDescr object is used to identify circuits using a textual description of up to 255 characters specified by the user. (Note that MIB objects are modified using network management system (NMS) applications, and can not be configured using the Cisco IOS command-line interface.) When the row is created by a user, a value is set for the cciDescr object. The table is indexed by ifIndex from the IF-MIB. The cciStatus is the RowStatus object for the rows in the table. The cciStatus object can be set to only two values by the user: createAndGo(4), which creates a new row, and destroy(6), which removes an existing row. If the row is created successfully, the cciStatus will be active(1). When creating a new row, the user should set the cciDescr object along with the cciStatus in a single snmp set pdu command. If the row is already active, only the cciDescr object can be modified. The other option is to delete the row first by setting the cciStatus to destroy(6) and then recreate the row with a new value for cciDescr. When creating a new row, the ifIndex is validated first. If the ifIndex value is not valid, the row is not created and an error code is returned. Similarly, if ,when an interface is deleted, there was a corresponding row in this table, that row will be deleted automatically.

After an identifying description is created for an interface by a user, the description (the cciDescr object) will be sent along with the other varbinds as part of linkup and linkdown trap notifications.

For further details, see the CISCO-CIRCUIT-INTERFACE-MIB.my file, available from the Cisco Connection Online MIB site at http://www.cisco.com/public/sw-center/netmgmt/cmtk/mibs.shtml.

Cisco AAA Server MIB and Additional Enhancements for the Cisco AS5300 and Cisco AS5800

Addition to show caller Command

The show caller command combines the output of the existing call-related show commands. This command displays connection status in summary or in detail. The summary field has been added (summary) to display the total number of calls, including the number of ISDN and Analog calls, since the last reload. This summary counter is cumulative of all calls since the NAS has been up, where other counters indicate the current number of calls in the NAS.

Using the show caller command provides the following benefits:

• Displays statistics or debug information for connections using a single command

• Replaces the need to know and use the various show commands

• Provides network management across all Cisco platforms

Cisco AAA Server MIB

This MIB provides statistics reflecting the state of AAA Server operation within the device and AAA communications with external servers.

The Cisco AAA Server MIB provides the following information:

• Distinct statistics for each AAA function

• Status of servers providing AAA functions

• Identities of external AAA servers

A server is defined as a logical entity that provides any of the three AAA functions. A TACACS+ server consists of all three functions with a single IP address and single TCP port. A RADIUS server can consist of the authentication/accounting pair with a single IP address but distinct UDP ports, or it may be just one of authentication or accounting.

Modification to reload Command for the Cisco AS5800

On the Cisco AS5800 only, to request that the Dial Shelf Controller (DSC) [or Dial Shelf Controllers in a redundant configuration] be reloaded at the same time as a reload on the Router Shelf, use the reload components all command. Formerly, to reload a Cisco AS5800, separate reload commands were needed for both the DSC and the Router Shelf.

Point-to-Point Password Authentication Protocol Refusal

This new command allows refusal of a peer's request to remote (Point-to-Point Protocol [PPP]) authenticate using Password Authentication Protocol (PAP).

Event MIB

The Event MIB is an asynchronous notification mechanism standardized for use by network management systems using Simple Network Management Protocol (SNMP). The Event MIB provides the ability to monitor Management Information Base (MIB) objects on a local or remote system using SNMP and initiate simple actions whenever a trigger condition is met. By allowing notifications based on events, the Network Management System (NMS) does not need to constantly poll managed devices to find out if something has changed.

Support of the Event MIB has been added to Cisco IOS software to work with a variety of network management systems and, when combined with the currently integrated Expression MIB support, provides a flexible and efficient way to monitor complex conditions on network devices. By allowing SNMP notifications to take place only when a specified condition occurs, Event MIB support reduces the load on affected devices, significantly improving the scalability of network management solutions.

For documentation, see http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121newft/121t/121t3/dtevent.htm

Fax Relay Packet Loss Concealment

This feature improves the current real-time fax over IP (commonly known as fax relay) implementation in Cisco gateways, allowing fax transmissions to work reliably over higher packet loss conditions.

In addition, this feature includes enhanced real-time fax debug capabilities and statistics. These debugs and statistics will give better visibility into the real-time fax operation in the gateway, allowing for improved field diagnostics and troubleshooting.

These improvements include configuration of fax relay ECM (Error Correction Mode) on the VoIP dial peer. ECM provides for error-free page transmission. This mode is available on fax machines that include memory for storage of the page data (usually high-end fax machines).

Individual SNMP Trap Support

The Individual SNMP Trap Support feature adds the ability to enable or disable SNMP system management notifications (traps) individually. SNMP traps that can be specified are "authentication", "linkup", "linkdown", and "coldstart". This feature expands the functionality of the snmp-server enable traps snmp command.

For documentation, see http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121newft/121t/121t3/dtitraps.htm

Monitoring Resource Availability on Cisco AS5300 Universal Access Servers

This set of features provides enhancements to improve visibility into the line and modem status for the network access server (NAS). The combined features in this document have been developed to monitor the NAS health conditions at the DS0 level, PRI bearer channel level, and modem level.

These features are enabled and disabled by enhanced command-line interface and MIBs.

NAS modem health monitoring is supported by the following features:

• DS0 Busyout Traps

• PRI Requested Channel Not Available Traps

• Modem Health Traps

• Controller Time Slots State

Network Side ISDN PRI Signaling, Trunking, and Switching

The Network Side ISDN PRI Signaling, Trunking, and Switching feature enables Cisco IOS software to replicate the public switched network interface to a PBX that is compatible with the National ISDN (NI) switch type and European Telecommunications Standards Institute (ETSI) Net5 switch type. Routers and PBXs are both traditionally CPE devices with respect to the public switched network interfaces. However, for Voice over IP (VoIP) applications, it is desirable to interface access servers to PBXs with the access server representing the public switched network.

Enterprise organizations use the current VoIP features with Cisco products as a method to reduce costs for long distance phone calls within and outside their organizations. However, there are times that a call cannot go over VoIP and the call needs to be placed using the Public Switched Telephone Network (PSTN). The customer then must have two devices connected to a PBX to allow some calls to be placed using VoIP and some calls to be placed over the PSTN. In contrast, this feature allows Cisco access servers to connect directly to user-side CPE devices such as PBXs and allows voice and data calls to be placed without requiring two different devices to be connected to the PBXs.

The ISDN Network Side PRI Signaling, Trunking, and Switching feature allows Cisco ISDN-enabled access servers to switch calls across interfaces as legacy phone switches do today and to mimic the behavior of the legacy phone switches.

Preauthentication with ISDN PRI and Channel-Associated Signaling

The Preauthentication with ISDN PRI and Channel-Associated Signaling feature allows a Cisco network access server (NAS) to determine if an incoming call may be answered on the basis of the called number, the calling number, or the call type. With an ISDN PRI (Primary Rate Interface), or with Channel-Associated Signaling (CAS), information about an incoming call is available to the NAS before the call is answered. The available call information includes the called station ID (DNIS), the calling station ID (CLID), and the bearer capability (call type).

When an incoming call arrives from the public network switch, but before it is answered, this feature enables the NAS to send the DNIS, CLID, and call type to a RADIUS server for authorization. If the server authorizes the call, then the NAS accepts the call. If the server does not authorize the call, then the NAS sends a disconnect message to the public network switch to reject the call. This feature supports the use of attribute 44 by the RADIUS server application, which allows user authentication based on the CLID at the same time.

This feature also supports the use of new RADIUS attributes. These RADIUS attributes are configured in the RADIUS preauthentication profiles to specify preauthentication behavior. They may also be used, for instance, to specify whether subsequent authentication should occur and, if so, what authentication method should be used.

In the event that the RADIUS server application becomes unavailable, this feature allows a guard timer to be set in the NAS. When the timer expires, the NAS uses a configurable parameter to accept or reject the incoming call without the authorization.

TCP Clear Performance Optimization

This feature provides inbound and outbound performance optimization for America Online (AOL) users of wholesale dialing services.

First introduced in Cisco IOS Release 12.1(1)AA, this feature is designed to provide more efficiency in the data transfers for AOL users who are using a Cisco network access server (the Cisco AS5800) to communicate with a wholesale dial carrier. It permits the Cisco AS5800 platform to support the maximum number of connections provided by two T3 connections (that is, 1344 connections) running the TCP Clear protocol with typical traffic loads.

New Hardware Features in Cisco IOS Release 12.1(2)T

There are no new hardware features in the Cisco AS5800 for Cisco IOS Release 12.1(2)T.

New Software Features in Cisco IOS Release 12.1(2)T

The following new software features are supported by the Cisco AS5800 for Cisco IOS Release 12.1(2)T:

AAA Server Group Deadtimer (CSCdp13160)

The AAA Server Group Deadtimer  feature allows each authentication, authorization, and accounting (AAA) server to be fully configured in the server group. Thus, it allows you to direct AAA traffic to separate groups of servers that have different operational characteristics.

With the introduction of this feature, deadtime has been added as a new attribute to the server group structure. In addition, a separate timer has been attached to each server host in every server group. Therefore, when a server is found to be unresponsive after numerous retransmissions and time-outs, the server is assumed to be dead. The timers attached to each server host in all server groups are triggered. In essence, the timers are checked and subsequent requests to a server (once it is assumed dead) are directed to alternate timers, if configured. When the network access server receives a reply from the server, it checks and stops all configured timers (if running) for that server in all server groups.

If the timer has expired, only the server to which the timer is attached is assumed to be alive. This becomes the only server that can be tried for later AAA requests using the server groups to which the timer belongs.

Preauthentication with ISDN PRI (CSCdm82434)

The feature allows a Cisco network access server (NAS) to determine if an incoming call may be answered on the basis of the called number, the calling number, or the call type. With an ISDN PRI (Primary Rate Interface), information about an incoming call is available to the NAS before the call is answered. The available call information includes the called station ID (DNIS), the calling station ID (CLID), and the bearer capability (call type).

When an incoming call arrives from the public network switch, but before it is answered, this feature enables the NAS to send the DNIS, CLID, and call type to a RADIUS server for authorization. If the server authorizes the call, then the NAS accepts the call. If the server does not authorize the call, then the NAS sends a disconnect message to the public network switch to reject the call. This feature supports the use of attribute 44 by the RADIUS server application, which allows user authentication based on the CLID at the same time.

This feature also supports the use of new RADIUS attributes. These RADIUS attributes are configured in the RADIUS preauthentication profiles to specify preauthentication behavior. They may also be used, for instance, to specify whether subsequent authentication should occur and, if so, what authentication method should be used.

In the event that the RADIUS server application becomes unavailable, this feature allows a guard timer to be set in the NAS. When the timer expires, the NAS uses a configurable parameter to accept or reject the incoming call without the authorization.

New Hardware Features in Cisco IOS Release 12.1(1) T

There are no new hardware features in the Cisco AS5800 for Cisco IOS Release 12.1(1)T.

New Software Features in Cisco IOS Release 12.1(1) T

The following new software feature is supported by the Cisco AS5800 for Cisco IOS Release 12.1(1)T:

Cisco H.323 Version 2 Phase 2

Cisco H.323 Version 2 Phase 2 upgrades Cisco IOS software by adding several optional features of the H.323 Version 2 specification and facilitates customized extensions to the Cisco Gatekeeper.

• H.323v2 Fast Connect

The Fast Connect feature allows endpoints to establish media channels without waiting for a separate H.245 connection to be opened. This streamlines the number of messages that are exchanged and the amount of processing that must be done before endpoint connections can be established.

• H.245 Tunneling

Through H.245 tunneling, H.245 messages are encapsulated within Q.931 messages without using a separate H.245 TCP connection. When tunneling is enabled, one or more H.245 messages can be encapsulated in any Q.931 message. H.245 tunneling is not supported as a standalone feature; initiation of H.245 tunneling procedures can be initiated only by using the dtmf-relay command, and only from an active Fast Connect call. Furthermore, if dtmf-relay is configured on a Version 2 VoIP dial peer and the active call has been established by using Fast Connect, tunneling procedures initiated by the opposite endpoint are accepted and supported.

H.245 tunneling is backward compatible with H.323 Version 1 configurations.

• H.450.2 Call Transfer

Call Transfer allows an H.323 endpoint to redirect an answered call to another H.323 endpoint. Cisco gateways support H.450.2 Call Transfer as the transferred and transferred-to party. The transferring endpoint must be an H.450-capable terminal; the Cisco gateway cannot act as the transferring endpoint. Gatekeeper-controlled or Gatekeeper-initiated Call Transfer is not supported.

---

Note   Certain devices are limited in their support of H.450. The Cisco 1700 and ubr820 platforms do not support Interactive Voice Response (IVR). Therefore, these platforms are not able to act as H.450 Transferring endpoints.

---

• H.450.3 Call Deflection

Call Deflection is a feature under H.450.3 Call Diversion (Call Forwarding) that allows a called H.323 endpoint to redirect the unanswered call to another H.323 endpoint. Cisco gateways support H.450.3 Call Deflection as the originating, deflecting, and deflected-to gateway. The Cisco gateway as the deflecting gateway will support invocation of Call Deflection only by using an incoming PRI QSIG message (a Call Deflection cannot be invoked by using any other trunk type).

• H.450.3 Call Deflection

Call Deflection is a feature under H.450.3 Call Diversion (Call Forwarding) that allows a called H.323 endpoint to redirect the unanswered call to another H.323 endpoint. Cisco gateways support H.450.3 Call Deflection as the originating, deflecting, and deflected-to gateway. The Cisco gateway as the deflecting gateway will support invocation of Call Deflection only by using an incoming PRI QSIG message (a Call Deflection cannot be invoked by using any other trunk type).

• Gateway Support for Voice-Port Description

This feature provides the Gatekeeper with a configurable string that identifies the voice port or T1/E1 span from which an incoming call entered the ingress gateway. This is done using a Cisco proprietary, nonstandard field that has been added to the ARQ message sent by the ingress gateway. The string in the ARQ corresponds to the setting of the voice-port description command.

Limitations and Restrictions

MIBs

The Cisco AS5800 supports the following MIBs:

• ATM-MIB

• CALL TRACKER MIB

• CISCO MEMORY POOL MIB

• CISCO TOKEN RING MIB

• CISCO-ATM2-MIB

• CISCO-ATM-IF-PHYS-MIB

• CISCO-ATM-SIG-DIAG-MIB

• CISCO-BULK-FILE-MIB

• CISCO-CALL-HISTORY-MIB

• CISCO-ENTITY-MIB

• CISCO-FRAME-RELAY-MIB

• CISCO-ISDN-MIB

• CISCO-POP-MGMT-MIB

• CISCO-SYSLOG-MIB

• CISCO-VPDN-MGMT-MIB

• EXPRESSION-MIB

• FDDI-SMT73-MIB

• FSIP MIB

• OLD-CISCO-CHASSIS-MIB

• OLD-CISCO-MEMORY-MIB

• PROCESS MIB

• RFC1398-MIB

• RTT Mon MIB

• SONET-MIB

Note   Cisco Management Information Base (MIB) User Quick Reference is no longer published. If you have an account with CCO, you can find the latest list of MIBs supported by Cisco. To reach the Cisco Network Management Toolkit, go to CCO, press Login, and click to Software Center: Network Mgmt Products: Cisco Network Management Toolkit: Cisco MIB.

Caveats

Caveats describe unexpected behavior in Cisco IOS software releases. Severity 1 caveats are the most serious caveats; severity 2 caveats are less serious.

For information on caveats in Cisco IOS Release 12.1 T, see Caveats for Cisco IOS Release 12.1T.  

All caveats in Cisco IOS Release 12.1 are also in Cisco IOS Release 12.1 T.

For information on caveats in Cisco IOS Release 12.1, see Caveats for Cisco IOS Release 12.1 , which lists severity 1 and 2 caveats and is located on CCO  and the Documentation CD-ROM.

Note   If you have an account with CCO, you can use Bug Navigator II to find caveats of any severity for any release. To reach Bug Navigator II, go to CCO and press Login. Then go to Software Center: Cisco IOS Software: Cisco Bugtool Navigator II. Another option is to go to http://www.cisco.com/support/bugtools.

Related Documentation

The following sections describe the documentation available for the Cisco AS5800. These documents consist of hardware and software installation guides, Cisco IOS configuration and command references, system error messages, and other documents.

Documentation is available as printed manuals or electronic documents.

Use these release notes with these documents:

• Release-Specific Documents

• Platform-Specific Documents

• Cisco IOS Software Documentation Set

Release-Specific Documents

The following documents are specific to Cisco IOS Release 12.1 and are located on CCO  and the Documentation CD-ROM:

• Cross-Platform Release Notes for Cisco  IOS Release 12.1 

On CCO  at:

Technical Documents: Documentation Home Page: Cisco IOS Software Configuration: Cisco IOS Release 12.1

On the Documentation CD-ROM at:

Cisco Product Documentation: Cisco IOS Software Configuration: Cisco IOS Release 12.1: Release Notes: Cross-Platform Release Notes

• Product bulletins, field notices, and other release-specific documents on CCO  at:

Technical Documents

• Caveats for Cisco IOS Release 12.1

See Caveats for Cisco IOS Release 12.1  and Caveats for Cisco IOS Release  12.1 T, which contain caveats applicable to all platforms for all maintenance releases of Cisco IOS Release 12.1 and Cisco IOS Release 12.1 T.

On CCO  at:

Technical Documents: Documentation Home Page: Cisco IOS Software Configuration: Cisco IOS Release 12.1: Caveats

On the Documentation CD-ROM at:

Cisco Product Documentation: Cisco IOS Software Configuration: Cisco IOS Release 12.1: Caveats

Platform-Specific Documents

These documents are available for the Cisco AS5800 on CCO  and the Documentation CD-ROM:

Feature Modules

Feature modules describe new features supported by Cisco IOS Release 12.1 T and are updates to the Cisco IOS documentation set. A feature module consists of a brief overview of the feature, benefits, configuration tasks, and a command reference. As updates, the feature modules are available online only. Feature module information is incorporated in the next printing of the Cisco IOS documentation set.

On CCO  at:

Technical Documents: Documentation Home Page: Cisco IOS Software Configuration: Cisco IOS Release 12.1: New Feature Documentation

On the Documentation CD-ROM at:

Cisco Product Documentation: Cisco IOS Software Configuration: Cisco IOS Release 12.1: New Feature Documentation

Cisco IOS Software Documentation Set

The Cisco IOS software documentation set consists of the Cisco IOS configuration guides, Cisco IOS command references, and several other supporting documents that are shipped with your order in electronic form on the Documentation CD-ROM--unless you specifically ordered the printed versions.

Documentation Modules

Each module in the Cisco IOS documentation set consists of two books: a configuration guide and a corresponding command reference. Chapters in a configuration guide describe protocols, configuration tasks, Cisco IOS software functionality, and contain comprehensive configuration examples. Chapters in a command reference provide complete command syntax information. Use each configuration guide with its corresponding command reference.

On CCO  and the Documentation CD-ROM, two master hot-linked documents provide information for the Cisco IOS software documentation set.

On CCO  at:

Technical Documents: Documentation Home Page: Cisco IOS Software Configuration: Cisco IOS Release 12.1: Configuration Guides and Command References

On the Documentation CD-ROM at:

Cisco IOS Release 12.1 Documentation Set

Table 5 describes the contents of the Cisco IOS Release 12.1 software documentation set for the AS5800, which is available in electronic form and in printed form if ordered.

Note   You can find the most current Cisco IOS documentation on CCO  and the Documentation CD-ROM. These electronic documents may contain updates and modifications made after the hard-copy documents were printed.

On CCO  at:

Technical Documents: Documentation Home Page: Cisco IOS Software Configuration: Cisco IOS Release 12.1

On the Documentation CD-ROM at:

---

Note   Cisco Management Information Base (MIB) User Quick Reference is no longer published. If you have an account with CCO, you can find the current list of MIBs supported by Cisco. To reach the Cisco Network Management Toolkit, go to CCO, press Login, and click to Software Center: Network Mgmt Products: Cisco Network Management Toolkit: Cisco MIB.

---

Obtaining Documentation

World Wide Web

You can access the most current Cisco documentation on the World Wide Web at http://www.cisco.com,   http://www-china.cisco.com,  or http://www-europe.cisco.com.  

Documentation CD-ROM

Cisco documentation and additional literature are available in a CD-ROM package, which ships with your product. The Documentation CD-ROM is updated monthly. Therefore, it is probably more current than printed documentation. The CD-ROM package is available as a single unit or as an annual subscription.

Ordering Documentation

Registered CCO users can order the Documentation CD-ROM and other Cisco Product documentation through our online Subscription Services at http://www.cisco.com/cgi-bin/subcat/kaojump.cgi.

Nonregistered CCO users can order documentation through a local account representative by calling Cisco's corporate headquarters (California, USA) at 408 526-4000 or, in North America, call 800 553-NETS (6387).

Obtaining Technical Assistance

Cisco provides Cisco Connection Online (CCO)  as a starting point for all technical assistance. Warranty or maintenance contract customers can use the Technical Assistance Center. All customers can submit technical feedback on Cisco documentation using the web, e-mail, a self-addressed stamped response card included in many printed documents, or by sending mail to Cisco.

Cisco Connection Online

Cisco continues to revolutionize how business is done on the Internet. Cisco Connection Online is the foundation of a suite of interactive, networked services that provides immediate, open access to Cisco information and resources at anytime, from anywhere in the world. This highly integrated Internet application is a powerful, easy-to-use tool for doing business with Cisco.

CCO's broad range of features and services helps customers and partners to streamline business processes and improve productivity. Through CCO, you will find information about Cisco and our networking solutions, services, and programs. In addition, you can resolve technical issues with online support services, download and test software packages, and order Cisco learning materials and merchandise. Valuable online skill assessment, training, and certification programs are also available.

Customers and partners can self-register on CCO to obtain additional personalized information and services. Registered users may order products, check on the status of an order and view benefits specific to their relationships with Cisco.

You can access CCO  in the following ways:

• WWW: www.cisco.com

• Telnet: cco.cisco.com

• Modem using standard connection rates and the following terminal settings: VT100 emulation; 8 data bits; no parity; and 1 stop bit.

  • From North America, call 408 526-8070

  • From Europe, call 33 1 64 46 40 82

You can e-mail questions about using CCO to cco-team@cisco.com.

Technical Assistance Center

The Cisco Technical Assistance Center (TAC) is available to warranty or maintenance contract customers who need technical assistance with a Cisco product that is under warranty or covered by a maintenance contract.

To display the TAC web site that includes links to technical support information and software upgrades and for requesting TAC support, use www.cisco.com/techsupport.

To contact by e-mail, use one of the following:

Language	E-mail Address
English	tac@cisco.com
Hanzi (Chinese)	chinese-tac@cisco.com
Kanji (Japanese)	japan-tac@cisco.com
Hangul (Korean)	korea-tac@cisco.com
Spanish	tac@cisco.com
Thai	thai-tac@cisco.com

In North America, TAC can be reached at 800 553-2447 or 408 526-7209. For other telephone numbers and TAC e-mail addresses worldwide, consult the following web site: http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml.

Software Configuration Tips on the Cisco Technical Assistance Center Home Page

If you have a CCO login account, you can access the following URL, which contains links and tips on configuring your Cisco products:

http://www.cisco.com/kobayashi/technotes/serv_tips.shtml

This URL is subject to change without notice. If it changes, point your Web browser to CCO, press Login, and click on this path: Technical Assistance Center: Technical Tips.

The following sections are provided from the Technical Tips page:

• Access Dial Cookbook--Contains common configurations or recipes for configuring various access routes and dial technologies.

• Field Notices--Notifies you of any critical issues regarding Cisco products and includes problem descriptions, safety or security issues, and hardware defects.

• Frequently Asked Questions--Describes the most frequently asked technical questions about Cisco hardware and software.

• Hardware--Provides technical tips related to specific hardware platforms.

• Hot Tips--Describes popular tips and hints gathered from the Cisco Technical Assistance Center (TAC). Most of these documents are available from the TAC Fax-on-demand service. To reach Fax-on-demand and receive documents at your fax machine from the United States, call 888 50-CISCO (888 502-4726). From other areas, call 650 596-4408.

• Internetworking Features--Lists tips on using Cisco  IOS software features and services.

• Sample Configurations--Provides actual configuration examples that are complete with topology and annotations.

Documentation Feedback

If you are reading Cisco product documentation on the World Wide Web, you can submit technical comments electronically. Click Feedback in the toolbar and select Documentation. After you complete the form, click Submit to send it to Cisco.

You can e-mail your comments to bug-doc@cisco.com.

To submit your comments by mail, for your convenience many documents contain a response card behind the front cover. Otherwise, you can mail your comments to the following address:

Cisco Systems, Inc.
Document Resource Connection
170 West Tasman Drive
San Jose, CA 95134-9883

We appreciate and value your comments.

Posted: Thu Aug 3 13:10:33 PDT 2000
Copyright 1989-2000©Cisco Systems Inc.