|
|
This section documents new and modified commands for the NextPort dial feature card (DFC) port management for the Cisco AS5400 and the universal port card (UPC) port management for the Cisco AS5800.
To disable a port by waiting for the active services on the specified port to terminate, use the busyout port configuration command. To re-enable the ports, use the no form of this command.
busyoutSyntax Description
This command has no arguments or keywords.
Defaults
Busyout is not enabled.
Command Modes
Port configuration.
Command History
12.1(1)XD This command was introduced on the Cisco AS5400. 12.1(3)T This command was supported on the Cisco AS5400 and Cisco AS5800.
Release
Modification
Usage Guidelines
The busyout command disables a port by waiting for the active services on the specified port to terminate. Use the no form of this command to re-enable the ports.
Examples
The following example shows output from the busyout command on the Cisco AS5400 with NextPort DFC. This example busies out ports 1 to 10 on slot 1:
Router(config)# port 1/1 1/10 Router(config-port)# busyout Router(config-port)#
Related Commands
clear port Resets the port and clears any active calls to the port. clear spe Reboots SPEs that are in any state. shutdown Takes a designated port or range of ports out of service. show spe Displays history statistics of all SPEs, a specified SPE, or the specified range of SPEs.
Command
Description
To disable active calls on the specified Service Processing Elements (SPEs), use the busyout SPE configuration command. To re-enable the SPEs, use the no form of this command.
busyoutSyntax Description
This command has no arguments or keywords.
Defaults
Busyout is not enabled.
Command Modes
SPE configuration.
Command History
12.1(1)XD This command was introduced on the Cisco AS5400. 12.1(3)T This command was supported on the Cisco AS5400 and Cisco AS5800.
Release
Modification
Usage Guidelines
You can perform auto-diagnostic tests and firmware upgrades when you put the SPEs in the Busiedout state. Active ports on the specified SPE will change the state of the specified range of SPEs to the BusyoutPending state. The state changes from BusyoutPending to Busiedout when all calls end. Use the show spe command to see the state of the range of SPEs. Use the shutdown command to override the busyout command. Use the no busyout command to re-enable the SPEs.
Examples
The following example shows output from the busyout command on the Cisco AS5400 with NextPort DFC. This example busies out all active ports in slot 1, SPE 1 to 10:
Router(config)# spe 1/1 1/10 Router(config-spe)# busyout Router(config-spe)#
Related Commands
clear port Resets the port and clears any active calls to the port. clear spe Reboots SPEs that are in any state. shutdown Takes a designated port or range of ports out of service. show spe Displays history statistics of all SPEs, a specified SPE, or the specified range of SPEs.
Command
Description
To reset the NextPort port and clear any active call to the port, use the clear port EXEC command.
Cisco AS5400 with NextPort DFC
clear port [slot | slot/port]
Cisco AS5800 with universal port card
clear port [shelf/slot | shelf/slot/port]
Syntax Description
slot (Optional) All ports on the specified slot. For the AS5400, slot values range from 0 to 7. slot/port (Optional) All ports on the specified slot and SPE. For the AS5400, slot values range from 0 to 7 and port values range from 0 to 107. shelf/slot (Optional) All ports on the specified shelf and slot. For the AS5800, shelf values range from 0 to 1 and UPC slot values range from 2 to 11. shelf/slot/port (Optional) All ports on the specified SPE. For the AS5800, shelf values range from 0 to 1, slot values range from 2 to 11, and port values range from 0 to 323.
Defaults
No default.
Command Modes
EXEC
Command History
12.1(1)XD This command was introduced on the Cisco AS5400. 12.1(3)T This command was supported on the Cisco AS5400 and Cisco AS5800.
Release
Modification
Usage Guidelines
If you specify the shelf, slot, and port, you clear that port on that Service Processing Element (SPE). If you only specify the shelf and slot, you clear all active ports on that particular shelf and slot. If you do not specify a shelf, slot, or port, you clear all the ports on the access server.
Examples
The following example shows output from the clear port command on the Cisco AS5400 with NextPort DFC. This example clears slot 1, port 1:
Router# clear port 1/1 This will clear port 1/01[confirm]y
The following example shows output from the clear port command on the Cisco AS5800 with universal port card. This example clears shelf 1, slot 3, port 0:
Router# clear port 01/03/00 This will clear port 1/03/00[confirm]y
Related Commands
busyout Disables a port by waiting for the active services on the specified port to terminate. clear spe Reboots SPEs that are in any state. clear line Returns a line to its Idle state. shutdown Takes a designated port or range of ports out of service. show port digital log Displays the digital data event log with the oldest event first. show port modem log Displays the modem port history event log or modem test log. show spe Displays history statistics of all SPEs, a specified SPE, or the specified range of SPEs.
Command
Description
To clear all event entries in the port level history event log, use the clear port log EXEC command.
Cisco AS5400 with NextPort DFC
clear port log [slot | slot/port]
Cisco AS5800 with universal port card
clear port log [shelf/slot | shelf/slot/port]
Syntax Description
slot (Optional) All ports on the specified slot. For the AS5400, slot values range from 0 to 7. slot/port (Optional) All ports on the specified slot and SPE. For the AS5400, slot values range from 0 to 7 and port values range from 0 to 107.
Defaults
Disabled
Command Modes
EXEC
Command History
12.1(1)XD This command was introduced on the Cisco AS5400. 12.1(3)T This command was supported on the Cisco AS5400 and Cisco AS5800.
Release
Modification
Usage Guidelines
The clear port log command clears the entire port log. You cannot remove individual service events from the port log. On the Cisco AS5400 only, you can use show port modem log and/or the show port digital log to display specific service events, but you must use clear port log to clear the entire port event log.
Examples
The following example shows output from the clear port log command on the Cisco AS5400 with NextPort DFC. This example clears slot 1, port 1:
Router# clear port log 1/1 This will clear log event history for port(s)1/01 - 1/01[confirm]y
The following example shows output from the clear port log command on the Cisco AS5800 with universal port card. This example clears shelf 1, slot 3, port 0:
Router#clear port log 01/03/00 This will clear port 1/03/00[confirm]y
Related Commands
show port log Displays all event entries in the port level history event log show port modem log Displays the events generated by the modem sessions. show port digital log Displays the digital data event log.
Command
Description
To reboot all specified Service Processing Elements (SPEs), use the clear spe EXEC command.
Cisco AS5400 with NextPort DFC
clear spe [slot | slot/spe]
Cisco AS5800 with universal port card
clear spe [shelf/slot | shelf/slot/spe]
Syntax Description
slot (Optional) All ports on the specified slot. For the AS5400, slot values range from 0 to 7. slot/spe (Optional) All ports on the specified slot and SPE. For the AS5400, slot values range from 0 to 7 and SPE values range from 0 to 17. shelf/slot (Optional) All ports on the specified shelf and slot. For the AS5800, shelf values range from 0 to 1 and UPC slot values range from 2 to 11. shelf/slot/spe (Optional) All ports on the specified SPE. For the AS5800, shelf values range from 0 to 1, slot values range from 2 to 11, and SPE values range from 0 to 53.
Defaults
Disabled
Command Modes
EXEC
Command History
12.1(1)XD This command was introduced on the Cisco AS5400. 12.1(3)T This command was supported on the Cisco AS5400 and Cisco AS5800.
Release
Modification
Usage Guidelines
Execution of the clear spe command causes the configured firmware to be downloaded to the specified SPE or the range of SPEs and causes power-on self-test (POST) to be executed. This command can be executed regardless of the state of the SPEs.
 |
Caution All active ports running on the SPE are prematurely terminated and messages are logged into the appropriate log. |
This command downloads configured SPEs with firmware as configured. Unconfigured SPEs download with the default firmware, which is the bundled version. To configure and mange the downloading of firmware without abruptly terminating SPEs, use the firmware location or firmware upgrade commands as appropriate.
Examples
The following example clears SPEs when the clear spe command is entered on the Cisco AS5400 with NextPort DFC. This example performs a coldstart on slot 1, SPE 1.
Router# clear spe 1/1 Router# This will tear all active calls on the SPE(s), if any.[confirm]y
The following example clears SPEs when the clear spe command is entered on the Cisco AS5800 with universal port card. This example performs a coldstart on slot 1, slot 8. SPE 0.
Router# clear spe 1/8/0 Router# This will tear all active calls on the SPE(s), if any.[confirm]y
Related Commands
busyout Disables a port by waiting for the active services on the specified port to terminate. clear line Returns a line to its idle state. clear port Resets the port and clears any active calls to the port. shutdown Takes a designated port or range of ports out of service. show spe Displays history statistics of all SPEs, a specified SPE, or the specified range of SPEs.
Command
Description
To clear all statistics, use the clear spe counters EXEC command.
Cisco AS5400 with NextPort DFC
clear spe counters [slot | slot/spe]
Cisco AS5800 with universal port card
clear spe counters [shelf/slot | shelf/slot/spe]
Syntax Description
slot (Optional) All ports on the specified slot. For the AS5400, slot values range from 0 to 7. slot/spe (Optional) All ports on the specified slot and SPE. For the AS5400, slot values range from 0 to 7 and SPE values range from 0 to 17. shelf/slot (Optional) All ports on the specified shelf and slot. For the AS5800, shelf values range from 0 to 1 and UPC slot values range from 2 to 11. shelf/slot/spe (Optional) All ports on the specified SPE. For the AS5800, shelf values range from 0 to 1, slot values range from 2 to 11, and SPE values range from 0 to 53.
Defaults
Disabled.
Command Modes
EXEC
Command History
12.1(1)XD This command was introduced on the Cisco AS5400. 12.1(3)T This command was supported on the Cisco AS5400 and Cisco AS5800.
Release
Modification
Usage Guidelines
The clear spe counters command clears statistical counters of all service types for the specified SPE, range of SPEs, or all the SPEs. If you do not set a parameter, you clear all SPE statistical counters.
Related Commands
None.
Examples
The following example clears all statistics when the clear spe counters command is entered on the Cisco AS5400 with NextPort DFC.
Router# clear spe counters 01/3 01/7 This will clear statistic counters for SPEs 1/03 - 1/07 [confirm]y
The following example clears all statistics when the clear spe counters command is entered on the Cisco AS5800 with universal port card. This example clears shelf 1, slot 3, ports 0 to 11.
Router# clear spe counters 01/03/00 01/03/11 This will clear statistic counters for SPEs 1/03/00 - 1/03/11[confirm]y
Related Commands
No related commands.
To clear event entries in the slot history event log, use the clear spe log EXEC command.
Cisco AS5400 with NextPort DFC
clear spe log [slot]
Cisco AS5800 with universal port card
clear spe log [shelf/slot]
Syntax Description
slot (Optional) All ports on the specified slot. For the AS5400, slot values range from 0 to 7. shelf/slot (Optional) All ports on the specified shelf and slot. For the AS5800, shelf values range from 0 to 1 and UPC slot values range from 2 to 11.
Defaults
No default.
Command Modes
EXEC
Command History
12.1(1)XD This command was introduced on the Cisco AS5400. 12.1(3)T This command was supported on the Cisco AS5400 and Cisco AS5800.
Release
Modification
Usage Guidelines
The clear spe log command clears event entries in the slot history event log. If you do not specify the shelf/slot range, all Service Processing Element (SPE) event entries clear.
If you specify the shelf/slot, only the event entries for that slot clear.
Examples
The following example shows output from the clear spe log command on the Cisco AS5400 with NextPort DFC. This example clears the SPE log from shelf 1, slot 3. Router# clear spe log 1/03 This will clear slot event history for slot(s) 3 - 3[confirm]y
The following example shows output from the clear spe log command on the Cisco AS5800 with universal port card. This example clears shelf 1, slot 8, SPE 0.
Router# clear spe log 1/8/0
This will clear slot event history for slot(s) 8 - 8[confirm]
Related Commands
show spe log Displays history statistics of all SPEs, a specified SPE, or the specified range of SPEs.
Command
Description
To specify a firmware file to upgrade, use the firmware location SPE configuration command.
firmware location filename
Syntax Description
filename The name of the firmware file to download.
Defaults
No defaults.
Command Modes
SPE configuration.
Command History
12.0(4)XI1 This command was introduced on the Cisco AS5200, Cisco 5300, and Cisco AS5800. 12.0(7)T This command was supported on the Cisco AS5300 and Cisco AS5800 for MICA modems. 12.1(1)XD This command was introduced on the Cisco AS5400 for the NextPort DFC. 12.1(3)T This command was supported on the Cisco AS5400 for Nextport dial feature card (DFC) and Cisco AS5800 for universal port card (UPC).
Release
Modification
Usage Guidelines
You can get the new Service Processing Element (SPE) firmware image on Cisco's web site. You must first copy the SPE image from a TFTP server to the Flash memory using the copy tftp flash command. This command specifies the location of the firmware file and downloads the firmware in the range of SPEs. Your range is specified depending on the states you configured using the firmware upgrade command.
Use the firmware location command in conjunction with the firmware upgrade command. The entire SPE is necessarily affected by the firmware location command.
The copy modem flash command is replaced by these commands for the NextPort DFC on the Cisco AS5400.
You cannot use this command on SPE that are in Bad state.
 |
Note Use this command when traffic is low, because the firmware location download does not begin until the modems have no active calls. Otherwise, use the firmware upgrade command to customize the scheduling of modem downloads for your needs. |
Examples
The following example sets the SPEs, specifies the firmware file location, opens the file (if on Flash memory), and downloads to the SPE on the Cisco AS5400.
Router(config)# spe 1/03 Router(config-spe)# firmware location Router(config-spe)# end
The following example sets the SPEs, specifies the firmware file location in Flash memory, downloads to the SPE, and reports on the status using the show spe version command on the Cisco AS5800.
Router(config)# spe 1/03 Router(config-spe)# firmware location flash:np_6_75 Started downloading firmware flash:np_6_75.spe Router(config-spe)# Router# show spe version 1/03 ... SPE SPE SPE SPE Port Call SPE# Port # State Busyout Shut Crash State Type 1/03/00 0000-0011 ACTIVE 0 0 0 ____________ ____________ 1/03/01 0012-0023 ACTIVE 0 0 0 ____________ ____________ 1/03/02 0024-0035 ACTIVE 0 0 0 ____________ ____________ 1/03/03 0036-0047 ACTIVE 0 0 0 ____________ ____________ 1/03/04 0048-0059 ACTIVE 0 0 0 ____________ ____________ 1/03/05 0060-0071 ACTIVE 0 0 0 ____________ ____________ 1/03/06 0072-0083 ACTIVE 0 0 0 ____________ ____________ 1/03/07 0084-0095 ACTIVE 0 0 0 ____________ ____________ 1/03/08 0096-0107 ACTIVE 0 0 0 ____________ ____________ 1/03/09 0108-0119 ACTIVE 0 0 0 ____________ ____________ 1/03/10 0120-0131 ACTIVE 0 0 0 ____________ ____________ 1/03/11 0132-0143 ACTIVE 0 0 0 ____________ ____________...
Related Commands
clear spe Reboots SPEs that are in any state. clear port Resets the port and clears any active calls to the port. copy tftp flash Copies the SPE image from a tftp server to the flash. firmware upgrade Specifies the method in which the SPE will be downloaded. show spe version Displays the firmware version on an SPE. spe download maintenance Performs download maintenance on SPEs that are marked for recovery. spe recovery Sets an SPE port for recovery.
Command
Description
To specify a Service Processing Element (SPE) firmware upgrade method, use the firmware upgrade SPE configuration command.
firmware upgrade {busyout | download-maintenance | reboot}
Syntax Description
busyout Upgrades when all calls are terminated on the SPE. download-maintenance Upgrades during download maintenance time. reboot Upgrades at the next reboot.
Defaults
No default.
Command Modes
SPE configuration
Command History
12.0(4)XI1 This command was introduced on the Cisco AS5200, Cisco 5300, and Cisco AS5800. 12.0(7)T This command was introduced on the Cisco AS5300 and Cisco AS5800 for MICA modems. 12.1(1)XD This command was introduced on the Cisco AS5400 for the NextPort DFC. 12.1(3)T This command was supported on the Cisco AS5400 for Nextport dial feature card (DFC) and Cisco AS5800 for universal port card (UPC).
Release
Modification
Usage Guidelines
Three methods of upgrade are available: busyout, reboot, and download-maintenance.
The reboot keyword requests the Cisco access servers to upgrade SPE firmware at the next reboot. The busyout keywords upgrades SPE firmware after waiting for all calls to be terminated on an SPE. The download-maintenance keyword requests SPE firmware download during maintenance time.
Use this command in conjunction with the firmware location command and the spe download maintenance command.
The SPE firmware location command is designed to integrate all continuous ranges of SPEs containing the same firmware location. However, the firmware upgrade command does not affect the ranges of SPEs. As such, all SPEs within the ranges of SPEs must have the same firmware upgrade mode or the router uses the default upgrade mode to busyout state. As such, if you want to upgrade a single SPE within an existing range of SPEs with a different upgrade mode than is currently configured, you must first change the upgrade mode for the entire range of SPEs and then change the firmware location for the specific SPE being upgraded.
Furthermore, each time you merge ranges of SPEs due to configuration changes, verify that the configuration of the SPE firmware upgrade remains effective to what is desired.
Examples
The following example sets the SPEs and specifies the firmware upgrade to take place once all calls are terminated on the SPE:
Router(config)# spe 1/03 Router(config-spe)# firmware location Router(config-spe)# firmware upgrade busyout Router(config-spe)#
If the busyout upgrade command is specified, or if no upgrade mode is specified, the SPE modems are set into a "pending download" state when you use the firmware location command on the specified SPE. The pending download state prevents any modem in that state to be allocated for new calls until the state is cleared. Modems with active calls remain active for their call durations, but enter the pending download state when they terminate. This pending download state can be cleared only when the SPE is finally downloaded. When all modems within the SPE are in the pending download state and no active calls remain on the SPE, the SPE is reloaded. The busyout option is the fastest way to upgrade modems on an active router but can severely impact the capacity of the router during the upgrade. The following example sets the default option for the firmware upgrade process:
Router(config-spe)# firmware upgrade busyout
If reboot upgrade is specified, the SPE modems are not reloaded to the new firmware location until the router is rebooted. The reboot upgrade option is useful for routers that need to have their SPE upgraded and that are also going to be rebooted for maintenance. When the new firmware is configured, the configuration takes effect after the reboot takes place. The following example sets the firmware upgrade reboot:
Router(config-spe)# firmware upgrade reboot
If recovery upgrade is specified, the SPE modems are reloaded based on the modem recovery algorithm. Only when no active calls exist on the SPE does the firmware download take place. Furthermore, at the configured "modem recovery maintenance time" (3:00 a.m.), the modem recovery maintenance process attempts, in a controller fashion, to reload the modems by busying out the modems for a window duration of time to make the download take place. Consult the modem recovery documentation for further details. The recovery upgrade option is the least impacting way to upgrade modems on an active router. Capacity is kept at a maximum. However, this option may take a few days for all modems to be reloaded to the new firmware location. The following example sets the system for a firmware upgrade recovery:
Router(config-spe)# firmware upgrade recovery
Related Commands
firmware location Downloads firmware into the modems from this file location. show spe version Displays the firmware version on an SPE. spe download maintenance Performs download maintenance on SPEs that are marked for recovery. spe recovery Sets an SPE port for recovery.
Command
Description
To enter the port configuration mode, use the port global configuration command. To exit port configuration mode, use the exit command.
Cisco AS5400 with NextPort DFC
port {slot | slot/port}
Cisco AS5800 with universal port card
port {shelf/slot | shelf/slot/port}
Syntax Description
slot All ports on the specified slot. For the AS5400, slot values range from 0 to 7. slot/port All ports on the specified slot and SPE. For the AS5400, slot values range from 0 to 7 and port values range from 0 to 107. shelf/slot All ports on the specified shelf and slot. For the AS5800, shelf values range from 0 to 1 and UPC slot values range from 2 to 11. shelf/slot/port All ports on the specified SPE. For the AS5800, shelf values range from 0 to 1, slot values range from 2 to 11, and port values range from 0 to 323.
Defaults
Disabled
Command Modes
Global configuration
Command History
12.1(3)T This command was introduced.
Release
Modification
Usage Guidelines
The port command helps you to enter the port configuration mode. The port configuration mode allows you to shut down or put individual ports or ranges of ports in busyout mode.
Examples
The following example shows how to enter the port configuring mode on ports 1 to 18 to perform further tasks on the ports:
Router# port 1/1 1/18 Router(config-port)# shutdown
Related Commands
clear port Resets the port and clears any active calls to the port.
Command
Description
To automatically and periodically perform a modem diagnostics test for modems inside the access server or router, use the port modem autotest global configuration command. Use the no form of this command to disable or turn off the modem autotest service.
port modem autotest {error threshold | minimum modem | time hh:mm [interval]}
Syntax Description
error threshold Maximum modem error threshold. When the system detects this many errors with the modems, the modem diagnostics test is automatically triggered. Specify a threshold count between 3 and 50. minimum modem Minimum number of modems that will remain untested and available to accept calls during each test cycle. You can specify between 5 and 48 modems. The default is 6 modems on the Cisco AS5400. The range for the Cisco AS5800 is 73 to 756. time hh:mm Time you want the modem autotest to begin. You must use the military time convention and a required colon (:) between the hours and minutes variables for this feature. For example, 1:30 a.m. is issued as 01:30. interval (Optional) Long-range time variable used to set the modem autotest more than one day in advance. The range of hours is between 1 hour and 168 hours. For example, if you want to run the test once per week, issue 168. There are 168 hours in one week.
Defaults
Modem diagnostics tests are disabled.
Command Modes
Global configuration
Command History
11.3 This command was introduced. 12.1(1)XD This command was introduced on the Cisco AS5400 as the port modem autotest command and replaced the modem autotest command only for the NextPort DFC. 12.1(3)T This command was supported on the Cisco AS5400 and Cisco AS5800.
Release
Modification
Examples
The following example shows how to set the modem autotest to run once per week at 3:00 a.m. Additionally, the autotest activates if the system detects a modem error count higher than 40 errors.
Determine the current time set on the access server with the show clock EXEC command. In this example, the time and date set is 3:00 p.m, Monday, August 25, 1997:
Router# show clock *15:00:01.031 EST Aug 25 1997
Enter global configuration mode and set the time you want the modem autotest to activate. In this example, the access server is configured to run the modem autotest each ongoing Tuesday at 3:00 a.m:
Router# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)# port modem autotest time 03:00 168
Configure the autotest to activate if the system detects a high modem error count. In this example, the autotest activates if the system detects a modem error count higher than 40 errors. For the list of modem errors that are monitored by the modem autotest command, see the show modem call-stats command.
Router(config)# port modem autotest error 40 Router(config)# exit
Related Commands
show clock Displays the system clock. show modem Displays a high-level performance report for all the modems or a single modem inside Cisco AS5200 and Cisco AS5300 access servers. show modem test Displays the modem test log.
Command
Description
To display the active session's configuration parameters, use the show port config EXEC command.
Cisco AS5400 with NextPort DFC
show port config {slot | slot/port}
Cisco AS5800 with universal port card
show port config {shelf/slot | shelf/slot/port}
Syntax Description
slot All ports on the specified slot. For the AS5400, slot values range from 0 to 7. slot/port All ports on the specified slot and SPE. For the AS5400, slot values range from 0 to 7 and port values range from 0 to 107. shelf/slot All ports on the specified shelf and slot. For the AS5800, shelf values range from 0 to 1 and UPC slot values range from 2 to 11. shelf/slot/port All ports on the specified SPE. For the AS5800, shelf values range from 0 to 1, slot values range from 2 to 11, and port values range from 0 to 323.
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
12.1(1)XD This command was introduced on the Cisco AS5400. 12.1(3)T This command was supported on the Cisco AS5800 and Cisco AS5400.
Release
Modification
Usage Guidelines
The port should have an associated active session when the show port config command is executed.
|
Note The show port config command is similar to the show modem config MICA modem command. |
Examples
The following example shows output from the show port config command on the Cisco AS5400 with NextPort DFC. This example shows port configuration for the modem service port slot 2, shelf 1:
Router# show port config 2/1 Slot/SPE/Port -- 2/0/1 Service Type :Modem service Originate/Answer Mode :Answer Data Bits Selection :8 Parity Selection :No Parity Stop bits Selection :1 V.42 ODP generation :Enabled EC Autodetect Time-out :5000 ms Protocol Negotiation Time-out :10000 ms Protocol Negotiation Fallback character :13 Protocol Negotiation Retransmission Limit :12 EC Min, Max Octets Frame length :256 Data Compression :V.42bis or MNP5 ARA Error Correction :ARA1.0 & ARA2.0 Disabled V.42 Error Correction :V.42(LAP-M) Originate&Answer enabled MNP Error Correction :MNP Originate&Answer enabled Link Protocol Fallback :Async Framing (Start/Stop/Parity) Calling Tone :Disabled Guard Tone :Disabled Modem Standard :V.90 Automode Max Non-PCM Connect Rate :33600 bps Min Non-PCM Connect Rate :300 bps Max PCM Connect Rate :60000 bps Min PCM Connect Rate :28000 bps Signal Quality Threshold :Bit Errors >= 1:1000 cause recovery Fallback/Fallforward Squelch Timer :500 ms Fall Forward Timer :10000 ms Fall Back Timer :500 ms Terminate Time-out :20 secs Wait for Data Mode Time-out :60 secs Lost Carrier To Hang-up Delay :1400 ms PCM Transmit Level Setting :-13 dBm Retrain Limit :4 V.34 Max Symbol Rate :3429 Baud V.34 Min Symbol Rate :2400 Baud V.34 Carrier Frequency :Auto Carrier Selection V.34 Preemphasis Filter Selection :11 +++ Escape Detection :Enabled-in-Originate-Mode-Only AT Command Processor :Enabled Call Setup Delay :0 ms Automatic Answer Delay :2 secs Escape Detection Character :ASCII 43 (+) Carriage Return Character :ASCII 13 (CR) Line Feed Character :ASCII 10 (LF) Backspace Character :ASCII 8 (BS) Pause Before Blind Dialing :2 secs Comma Dial Modifier Time :2 secs
The following example shows port configuration information for a digital service port slot 2, port 23 on the Cisco AS5400 with NextPort DFC.
Router# show port config 2/23 Slot/SPE/Port -- 2/3/23 Service Type : Digital service Originate/Answer Mode : Answer Data Bits Selection : 8 Parity Selection : No Parity Stop bits Selection : 1 Modem Standard : reserved
The following example shows port configuration information for a digital service port slot 2, port 23 on the Cisco AS5800 with universal port card.
Router# show port config 1/8 Shelf/Slot/SPE/Port -- 1/8/27/165 Service Type : Modem service Originate/Answer Mode : Answer Data Bits Selection : 8 Parity Selection : No Parity Stop bits Selection : 1 V.42 ODP generation : Enabled EC Autodetect Time-out : 5000 ms Protocol Negotiation Time-out : 10000 ms Protocol Negotiation Fallback character : 13 Protocol Negotiation Retransmission Limit : 12 EC Min, Max Octets Frame length : 256 Data Compression : V.42bis or MNP5 ARA Error Correction : ARA1.0 & ARA2.0 Disabled V.42 Error Correction : V.42(LAP-M) Originate&Answer enabled MNP Error Correction : MNP Originate&Answer enabled Link Protocol Fallback : Async Framing (Start/Stop/Parity) Calling Tone : Disabled Guard Tone : Disabled Modem Standard : V.90 Automode Max Non-PCM Connect Rate : 33600 bps Min Non-PCM Connect Rate : 300 bps Max PCM Connect Rate : 60000 bps ...
Related Commands
show port operational-status Displays the operational status of a specific port or port range.
Command
Description
To display the digital data event log, use the show port digital log EXEC command.
Cisco AS5400 with NextPort DFC
show port digital log [reverse slot/port] [slot | slot/port]
|
Note This command is not supported on the Cisco AS5800 with the universal port card. |
Syntax Description
reverse (Optional) Report displayed with most recent entry first. slot (Optional) All ports on the specified slot. For the AS5400, slot values range from 0 to 7. slot/port (Optional) All ports on the specified slot and SPE. For the AS5400, slot values range from 0 to 7 and port values range from 0 to 107.
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
12.1(1)XD This command was introduced on the Cisco AS5400. 12.1(3)T This command was supported on the Cisco AS5400.
Release
Modification
Examples
The following example shows output from the show port digital log on the Cisco AS5400 with NextPort DFC:
Router# show port digital log
Port 5/00 Events Log
00:02:41: incoming called number: 35140
Service type: DIGITAL_DATA
Session State: IDLE
Service type: DIGITAL_DATA
Session State: ACTIVE
00:02:41: Digital State event:
State: Steady
00:02:40: Digital Static event:
Connect Protocol : V.110
Data Bits : 8
Parity : 0
Stop Bits : 1
TX,RX Bit Rate : 19200, 19200
Port 5/01 Events Log
00:02:42: incoming called number: 35140
Service type: DIGITAL_DATA
Session State: IDLE
Service type: DIGITAL_DATA
Session State: ACTIVE
00:02:41: Digital State event:
State: Steady
00:02:41: Digital Static event:
Connect Protocol : V.110
Data Bits : 8
Parity : 0
Stop Bits : 1
TX,RX Bit Rate : 19200, 19200
Port 5/02 Events Log
00:02:42: incoming called number: 35140
Service type: DIGITAL_DATA
Session State: IDLE
Service type: DIGITAL_DATA
Session State: ACTIVE
00:02:42: Digital State event:
State: Steady
00:02:42: Digital Static event:
Connect Protocol : V.110
Data Bits : 8
Parity : 0
Stop Bits : 1
TX,RX Bit Rate : 19200, 19200
Port 5/03 Events Log
00:02:43: incoming called number: 35140
Service type: DIGITAL_DATA
Session State: IDLE
Service type: DIGITAL_DATA
Session State: ACTIVE
00:02:43: Digital State event:
State: Steady
00:02:43: Digital Static event:
Connect Protocol : V.110
Data Bits : 8
Parity : 0
...
Related Commands
clear port digital log Displays specific service events. clear port log Clears all event entries in the port level history event log. show port digital log reverse Views port events with the most recent event first.
Command
Description
To display the port level information for an active modem, use the show port modem calltracker EXEC command.
Cisco AS5400 with NextPort DFC
show port modem calltracker [slot | slot/port]
Cisco AS5800 with universal port card
show port modem calltracker [shelf/slot | shelf/slot/port]
Syntax Description
slot (Optional) All ports on the specified slot. For the AS5400, slot values range from 0 to 7. slot/port (Optional) All ports on the specified slot and SPE. For the AS5400, slot values range from 0 to 7 and port values range from 0 to 107. shelf/slot (Optional) All ports on the specified shelf and slot. For the AS5800, shelf values range from 0 to 1 and UPC slot values range from 2 to 11. shelf/slot/port (Optional) All ports on the specified SPE. For the AS5800, shelf values range from 0 to 1, slot values range from 2 to 11, and port values range from 0 to 323.
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
12.1(1)XD This command was introduced on the Cisco AS5400. 12.1(3)T This command was supported on the Cisco AS5400 and Cisco AS5800.
Release
Modification
Usage Guidelines
When there is no call on the specified port, the most recent call information is displayed. This command uses the calltracker database. To enable calltracker, enter the calltracker enable global configuration command.
Examples
The following example shows output from the show port modem calltracker command on the Cisco AS5400 with NextPort DFC. This example shows output for slot 3, port 3.
Router# show port modem calltracker 3/3
-------------------------- call handle= 62 --------------------------
status=Active, service=PPP, origin=Answer, category=Modem
DS0 slot/port/ds1/chan=4/7/7/0, called=124, calling=(n/a)
userid=as5300-ref2, ip=192.169.124.1, mask=255.255.255.0
setup=06/22/2000 21:50:47, conn=6.77, phys=25.00, service=29.83, authen=29.83
init rx/tx b-rate=33600/33600, rx/tx chars=0/0
resource slot/port=3/3, mp bundle=0, charged units=0, account id=0
idb handle=0x645B97CC, tty handle=0x622207BC, tcb handle=0x0
----------------------------------------------------------------------------
protocol: last=LAP-M, attempted=LAP-M
compression: last=V.42bis-Both, supported= V.42bis-RX V.42bis-TX
standard: last=V.34+, attempted=V.21, initial=V.21
snr=40 dB, sq=5, rx/tx level=-15/0 dBm
phase jitter: freq=1 Hz, level=2 degrees
far end echo level=-90 dBm, freq offset=0 Hz
phase roll=0 degrees, round-trip delay=0 msecs
digital pad=None dB, digital pad comp=0
rbs pattern=0, constellation=0 point
rx/tx: symbol rate=3429/3429, carrier freq=1959/1959
rx/tx: trellis code=0/0, preemphasis index=0/0
rx/tx: constellation shape=Off/Off, nonlinear encode=Off/Off
rx/tx: precode=Off/Off, xmit level reduct=0/0 dBm
rx/tx: chars=0/0, general info=0x0
rx/tx: link layer chars=0/0, NAKs=0/0
error corrected: rx/tx=0/0, rx bad=0
ec retransmissions=0, retransmitted frames=0
rx/tx ppp slip=0/0, bad ppp slip=0
rx/tx b-rate: last=33600/33600, lowest=0/0, highest=0/0
phase 2 projected max rx b-rate: client=0, host=33600
phase 4 desired rx/tx b-rate: client=16384/25987, host=25987/42765
retrains: local=0, remote=0, failed=0
speedshift: local up/down=0/0, remote up/down=0/0, failed=0
v110: rx good=0, rx bad=0, tx=0, sync lost=0
SS7/COT status=0x00
v90: status=(Invalid #141), client=(n/a), failure=None
rx/tx: max neg I frame=128/128, neg window=0/128
v42bis size: dictionary=0, string=16
T401 timeouts=0, tx window closures=0, rx overruns=0
test err=0, reset=0, v0 synch loss=0
mail lost: host=0, sp=0
duration(sec)=0, disc reason=0x0
disc text=(n/a)
--------5---------10--------15--------20--------25--------30
line shape : 0x0000000000000000000000000000000000000000000000000000
v8bis capab : 0x12C9808081C609B502009481834347CB000000000000
v8bis mod sl: 0x00000000000000000000000000000000000000000000
v8 jnt menu : 0xC16513942A8D00000000000000000000000000000000
v8 call menu: 0x00C16513942A00000000000000000000000000000000
v90 training: 0x00000000
v90 sgn ptrn: 0x00000000
state trnsn : 0x0F0F010203041013151920FF000000000000000000000000000000000000
0000
portwre diag: 0x00000000000000000000000000000000
phase 2 info: 0x0200EFF41F120000003CEFF41F0200E001EFB4014082050B083470200001
1EEFB41440E1050008FCA707A707650D00000000000000000000
phase 4 info: 0x0DA70D65836583400040
----------------------------------------------------------------------------
Related Commands
There are no related commands.
To display the events generated by the modem sessions, use the show port modem log EXEC command.
Cisco AS5400 with NextPort DFC
show port modem log [reverse slot/port] [slot | slot/port]
Cisco AS5800 with universal port card
show port modem log [reverse shelf/slot/port] [shelf/slot | shelf/slot/port]
Syntax Description
reverse (Optional) Displays the modem port history event log with the most recent event first. slot (Optional) All ports on the specified slot. For the AS5400, slot values range from 0 to 7. slot/port (Optional) All ports on the specified slot and SPE. For the AS5400, slot values range from 0 to 7 and port values range from 0 to 107. shelf/slot (Optional) All ports on the specified shelf and slot. For the AS5800, shelf values range from 0 to 1 and UPC slot values range from 2 to 11. shelf/slot/port (Optional) All ports on the specified SPE. For the AS5800, shelf values range from 0 to 1, slot values range from 2 to 11, and port values range from 0 to 323.
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
12.1(1)XD This command was introduced on the Cisco AS5400. 12.1(3)T This command was supported on the Cisco AS5400 and Cisco AS5800.
Release
Modification
Usage Guidelines
The port modem test log displays the results of the SPE diagnostics tests.
Examples
The following example shows output for the Cisco AS5400 with NextPort DFC. This example shows the port history event log for slot 5, port 47:
Router# show port modem log 5/47
Port 5/47 Events Log
Service type: DATA_FAX_MODEM
Service mode: DATA_FAX_MODEM
Session State: IDLE
00:02:23: incoming called number: 35160
Service type: DATA_FAX_MODEM
Service mode: DATA_FAX_MODEM
Session State: IDLE
Service type: DATA_FAX_MODEM
Service mode: DATA_FAX_MODEM
Session State: ACTIVE
00:02:23: Modem State event:
State: Connect
00:02:16: Modem State event:
State: Link
00:02:13: Modem State event:
State: Train Up
00:02:05: Modem State event:
State: EC Negotiating
00:02:05: Modem State event:
State: Steady
00:02:05: Modem Static event:
Connect Protocol : LAP-M
Compression : V.42bis
Connected Standard : V.34+
TX,RX Symbol Rate : 3429, 3429
TX,RX Carrier Frequency : 1959, 1959
TX,RX Trellis Coding : 16/16
Frequency Offset : 0 Hz
Round Trip Delay : 0 msecs
TX,RX Bit Rate : 33600, 33600
Robbed Bit Signalling (RBS) pattern : 0
Digital Pad : None
Digital Pad Compensation : None
4 bytes of link info not formatted : 0x00 0x00 0x00 0x00 0x00
00:02:06:Modem Dynamic event:
Sq Value : 5
Signal Noise Ratio : 40 dB
Receive Level : -12 dBm
Phase Jitter Frequency : 0 Hz
Phase Jitter Level : 2 degrees
Far End Echo Level : -90 dBm
Phase Roll : 0 degrees
Total Retrains : 0
EC Retransmission Count : 0
Characters transmitted, received : 0, 0
Characters received BAD : 0
PPP/SLIP packets transmitted, received : 0, 0
PPP/SLIP packets received (BAD/ABORTED) : 0
EC packets transmitted, received OK : 0, 0
EC packets (Received BAD/ABORTED) : 0
This following example shows the port history event log with the most recent event first on slot 5, port 40:
Router# show port modem log reverse 5/40
Modem port 5/40 Events Log
00:02:18:Modem Dynamic event:
Sq Value : 5
Signal Noise Ratio : 38 dB
Receive Level : -12 dBm
Phase Jitter Frequency : 0 Hz
Phase Jitter Level : 0 degrees
Far End Echo Level : 0 dBm
Phase Roll : 0 degrees
Total Retrains : 0
EC Retransmission Count : 0
Characters transmitted, received : 0, 0
Characters received BAD : 0
PPP/SLIP packets transmitted, received : 0, 0
PPP/SLIP packets received (BAD/ABORTED) : 0
EC packets transmitted, received OK : 0, 0
EC packets (Received BAD/ABORTED) : 0
00:02:18: Modem Static event:
Connect Protocol : LAP-M
Compression : V.42bis
Connected Standard : V.90
TX,RX Symbol Rate : 8000, 3200
TX,RX Carrier Frequency : 1829, 1829
TX,RX Trellis Coding : 16/16
Frequency Offset : 0 Hz
Round Trip Delay : 4 msecs
TX,RX Bit Rate : 52000, 28800
Robbed Bit Signalling (RBS) pattern : 255
Digital Pad : None
Digital Pad Compensation : Enabled
4 bytes of link info not formatted : 0x00 0x00 0x00 0x00 0x00
00:02:23: Modem State event:
State: Steady
00:02:23: Modem State event:
State: EC Negotiating
00:02:36: Modem State event:
State: Train Up
00:02:39: Modem State event:
State: Link
00:02:46: Modem State event:
State: Connect
00:02:46: Port State Reached:
Service type: DATA_FAX_MODEM
Service mode: DATA_FAX_MODEM
Session State: ACTIVE
00:02:46: Port State Reached:
Service type: DATA_FAX_MODEM
Service mode: DATA_FAX_MODEM
Session State: IDLE
00:02:47: incoming called number: 6000
00:02:47: incoming caller number: 90002
The following example shows output for the Cisco AS5800 with universal port card. This example shows the port history event log for slot 8, ports 0 to 6:
Router# show port modem log 1/8/0 1/8/6
Port 1/08/00 Events Log
09:09:53: Service Type: DATA_FAX_MODEM
09:09:53: Service Mode: DATA_FAX_MODEM
09:09:53: Session State: FLUSHING
09:09:53: Service Type: DATA_FAX_MODEM
09:09:53: Service Mode: DATA_FAX_MODEM
09:09:53: Session State: IDLE
09:09:53: Modem State event:
State: Terminate
09:09:53: Modem End Connect event:
Call Timer : 26 secs
Disconnect Reason Info : 0x1F00
Type (=0 ): <unknown>
Class (=31 ): Requested by host
Reason (=0 ): non-specific host disconnect
Total Retrains : 0
EC Retransmission Count : 0
Characters transmitted, received : 2633, 485
Characters received BAD : 0
PPP/SLIP packets transmitted, received : 0, 0
PPP/SLIP packets received (BAD/ABORTED) : 0
EC packets transmitted, received OK : 27, 21
EC packets (Received BAD/ABORTED) : 0
09:09:54:Modem Link Rate event:
09:09:55: Service Type: DATA_FAX_MODEM
09:09:55: Service Mode: DATA_FAX_MODEM
09:09:55: Session State: IDLE
09:09:55: Service Type: DATA_FAX_MODEM
09:09:55: Service Mode: DATA_FAX_MODEM
09:09:55: Session State: ACTIVE
09:09:55: Modem State event:
State: Connect
09:09:55: Modem State event:
State: Link
09:09:55: Modem State event:
State: Train Up
09:09:55: Modem State event:
State: EC Negotiating
09:09:55: Modem State event:
State: Steady
09:09:55: Modem Static event:
Connect Protocol : LAP-M
Compression : V.42bis
Connected Standard : V.34+
TX,RX Symbol Rate : 3429, 3429
TX,RX Carrier Frequency : 1959, 1959
TX,RX Trellis Coding : 16/16
Frequency Offset : 0 Hz
Round Trip Delay : 1 msecs
TX,RX Bit Rate : 31200, 28800
Robbed Bit Signalling (RBS) pattern : 0
Digital Pad : None
Digital Pad Compensation : None
4 bytes of link info not formatted : 0x00 0x00 0x00 0x00 0x00
09:09:56: Modem Dynamic event:
Sq Value : 5
Signal Noise Ratio : 38 dB
Receive Level : -15 dBm
Phase Jitter Frequency : 13 Hz
Phase Jitter Level : 0 degrees
Far End Echo Level : -90 dBm
Phase Roll : 0 degrees
Total Retrains : 0
EC Retransmission Count : 0
Characters transmitted, received : 0, 0
Characters received BAD : 0
PPP/SLIP packets transmitted, received : 0, 0
PPP/SLIP packets received (BAD/ABORTED) : 0
EC packets transmitted, received OK : 0, 0
EC packets (Received BAD/ABORTED) : 0
09:09:58: Service Type: DATA_FAX_MODEM
09:09:58: Service Mode: DATA_FAX_MODEM
09:09:58: Session State: FLUSHING
09:09:58: Service Type: DATA_FAX_MODEM
09:09:58: Service Mode: DATA_FAX_MODEM
09:09:58: Session State: IDLE
09:09:58: Modem State event:
State: Terminate
...
Related Commands
clear port log Clears all event entries in the port level history event log. port modem startup-test Performs diagnostic testing for all modems. port modem autotest Automatically and periodically performs a modem diagnostics test for modems inside the access server or router. show port modem log reverse Displays the latest event first from the port history event log. test port modem back-to-back Connects two specified ports back-to-back and transfer a specified amount of data between the ports.
Command
Description
To display the modem test log, use the show port modem test EXEC command.
Cisco AS5400 with NextPort DFC
show port modem test [slot | slot/port]
Cisco AS5800 with universal port card
show port modem test [shelf/slot | shelf/slot/port]
Syntax Description
slot (Optional) All ports on the specified slot. For the AS5400, slot values range from 0 to 7. slot/port (Optional) All ports on the specified slot and SPE. For the AS5400, slot values range from 0 to 7 and port values range from 0 to 107. shelf/slot (Optional) All ports on the specified shelf and slot. For the AS5800, shelf values range from 0 to 1 and UPC slot values range from 2 to 11. shelf/slot/port (Optional) All ports on the specified SPE. For the AS5800, shelf values range from 0 to 1, slot values range from 2 to 11, and port values range from 0 to 323.
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
12.1(1)XD This command was introduced on the Cisco AS5400. 12.1(3)T This command was supported on the Cisco AS5400 and Cisco AS5800.
Release
Modification
Usage Guidelines
The port modem test log displays the results of the SPE diagnostics tests.
Examples
The following example shows output for the Cisco AS5400 with NextPort DFC. This example displays the results of the SPE startup test, SPE auto-test, and SPE back-to-back test.
|
Note The Reason column indicates why the test was started. The TIME INTERVAL is one of the triggers under autotest, the other being the error threshold. |
Router# show port modem test Date Time Modem Test Reason State Result 3/02 12:00:57 PM 2/01 Back-To-Back :STARTUP TEST Idle PASS 3/02 12:00:57 PM 2/00 Back-To-Back :STARTUP TEST Idle PASS 3/02 12:00:58 PM 2/02 Back-To-Back :STARTUP TEST Idle PASS 3/02 12:00:58 PM 2/03 Back-To-Back :STARTUP TEST Idle PASS 3/02 12:00:58 PM 2/04 Back-To-Back :STARTUP TEST Idle PASS 3/02 12:00:58 PM 2/05 Back-To-Back :STARTUP TEST Idle PASS ... 3/02 12:01:14 PM 3/95 Back-To-Back :STARTUP TEST Idle PASS 3/02 12:01:14 PM 3/94 Back-To-Back :STARTUP TEST Idle PASS 3/02 12:01:15 PM 3/75 Back-To-Back :STARTUP TEST Idle PASS 3/02 12:01:15 PM 3/74 Back-To-Back :STARTUP TEST Idle PASS 3/02 12:13:52 PM 3/20 Back-To-Back :USER INITIATED Idle PASS 3/02 12:13:52 PM 2/10 Back-To-Back :USER INITIATED Idle PASS ... 3/02 12:44:00 PM 3/102 No Test (Time) :MIN IDLE MODEMS Idle NOTST 3/02 12:44:00 PM 3/103 No Test (Time) :MIN IDLE MODEMS Idle NOTST 3/02 12:44:00 PM 3/104 No Test (Time) :MIN IDLE MODEMS Idle NOTST 3/02 12:44:00 PM 3/105 No Test (Time) :MIN IDLE MODEMS Idle NOTST 3/02 12:44:00 PM 3/106 No Test (Time) :MIN IDLE MODEMS Idle NOTST 3/02 12:44:00 PM 3/107 No Test (Time) :MIN IDLE MODEMS Idle NOTST 3/02 12:44:21 PM 2/73 Back-To-Back :TIME INTERVAL Idle PASS 3/02 12:44:21 PM 2/72 Back-To-Back :TIME INTERVAL Idle PASS 3/02 12:44:21 PM 2/33 Back-To-Back :TIME INTERVAL Idle PASS 3/02 12:44:21 PM 2/32 Back-To-Back :TIME INTERVAL Idle PASS 3/02 12:44:21 PM 3/37 Back-To-Back :TIME INTERVAL Idle PASS
Related Commands
clear port log Clears all event entries in the port level history event log. port modem autotest Automatically and periodically performs a modem diagnostics test for modems inside the access server or router. port modem startup-test Performs diagnostic testing for all modems. show port modem log Displays the modem port history event log or modem test log. show port modem log reverse Displays the latest event first from the port history event log. test port modem back-to-back Connects two specified ports back-to-back and transfer a specified amount of data between the ports.
Command
Description
To display the active session's statistics, use the show port operational-status EXEC command.
Cisco AS5400 with NextPort DFC
show port operational-status {slot | slot/port}
Cisco AS5800 with universal port card
show port operational-status {shelf/slot | shelf/slot/port}
Syntax Description
slot All ports on the specified slot. For the AS5400, slot values range from 0 to 7. slot/port All ports on the specified slot and SPE. For the AS5400, slot values range from 0 to 7 and port values range from 0 to 107. shelf/slot All ports on the specified shelf and slot. For the AS5800, shelf values range from 0 to 1 and UPC slot values range from 2 to 11. shelf/slot/port All ports on the specified SPE. For the AS5800, shelf values range from 0 to 1, slot values range from 2 to 11, and port values range from 0 to 323.
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
12.1(1)XD This command was introduced on the Cisco AS5400. 12.1(3)T This command was supported on the Cisco AS5400 and Cisco AS5800.
Release
Modification
Usage Guidelines
This command displays the operational status of a specific port or port range. The port should have an associated active modem session when the command is executed.
Examples
The following example shows output from the show port operational-status command on the Cisco AS5400 with NextPort DFC. This example displays operational status for slot 2, SPE 0, port 1:
Router# show port operational-status 2/1 slot/spe/Port -- 2/0/1 Service Type :Modem service Disconnect Reason Info :0x0 Type (=0 ): <unknown> Class (=0 ): Other Reason (=0 ): no disconnect has yet occurred Modulation Standard :V.34+ TX/RX Bit Rate :31200/14400 Connect Protocol :LAP-M Compression :V.42bis Call Timer :47 secs Link Signal Quality :7 SNR :37 dB TX/RX Symbol Rate :3429/3429 TX/RX Carrier Frequency :1959/1959 TX/RX Trellis Coding :16/16 TX/RX Preemphasis Index :0/1 TX/RX Constellation Shaping :On-Active/On-Active TX/RX Nonlinear Encoding :On-Active/On-Active TX/RX Precoding :On-Active/On-Active TX/RX Xmit Level Reduction :3/1 dBm Receive Level :-15 dBm Frequency Offset :0 Hz Phase Jitter Frequency :2 Hz Phase Jitter Level :2 degrees Far End Echo Level :-90 dBm Phase Roll :0 degrees Round Trip Delay :0 msecs >Total Retrains :0 Self Test Error count :0 EC Retransmission count :0 EC packets transmitted/received OK :11/12 EC packets (Received BAD/ABORTED) :0 Characters transmitted/received :76/13 Characters received BAD :0 PPP/SLIP packets transmitted/received :0/0 PPP/SLIP packets received (BAD/ABORTED) :0 RBS Pattern :0 Digital Pad :0 Digital Pad Compensation :0
The following example displays operational status for a V.110 digital service for the Cisco AS5400 on slot 2, SPE 3, port 23:
Router# show port operational-status 2/23 slot/spe/Port -- 2/3/23 Service Type : Digital service Connect Protocol : V110 Data Bits : 8 Parity : 0 Stop Bits : 1 TX/RX Bit Rate : 19200/19200 Call Timer : 116 secs EC packets transmitted/received OK : 0/0 EC packets (Received BAD/ABORTED) : 0 PPP/SLIP packets transmitted, received : 8/8 PPP/SLIP packets received (BAD/ABORTED) : 0 Sync Loss : 0
The following example shows the show port operational-status command for the Cisco AS5800 on shelf 1, slot 8:
Router# show port operational-status 1/8
Shelf/Slot/SPE/Port -- 1/8/32/194
Service Type : Modem service
Disconnect Reason Info : 0x0
Type (=0 ): <unknown>
Class (=0 ): Other
Reason (=0 ): no disconnect has yet occurred
Modulation Standard : V.34+
TX/RX Bit Rate : 31200/31200
Connect Protocol : LAP-M
Compression : V.42bis
Call Timer : 18 secs
Link Signal Quality : 6
SNR : 38 dB
TX/RX Symbol Rate : 3429/3429
TX/RX Carrier Frequency : 1959/1959
TX/RX Trellis Coding : 16/16
TX/RX Preemphasis Index : 0/1
TX/RX Constellation Shaping : Off-None/On-Active
TX/RX Nonlinear Encoding : Off-None/On-Active
TX/RX Precoding : Off-None/On-Active
TX/RX Xmit Level Reduction : 6/5 dBm
Receive Level : -15 dBm
Frequency Offset : 0 Hz
Phase Jitter Frequency : 5 Hz
Phase Jitter Level : 2 degrees
Far End Echo Level : -90 dBm
Phase Roll : 0 degrees
Round Trip Delay : 1 msecs
Total Retrains : 0
Self Test Error count : 0
EC Retransmission count : 1
EC packets transmitted/received OK : 34/14
EC packets (Received BAD/ABORTED) : 0
Characters transmitted/received : 9393/355
Characters received BAD : 0
PPP/SLIP packets transmitted/received : 0/0
PPP/SLIP packets received (BAD/ABORTED) : 0
RBS Pattern : 0
Digital Pad : 0
Digital Pad Compensation : 0
...
See Table 1 for field definitions for output display of the show modem operational-status command.
| Field | Definition |
|---|---|
Call Timer | Length of the call in seconds. The timer starts once the CONNECT modem state is reached. |
Characters received BAD | Total number of parity errored characters, which is a subset of Characters transmitted/received. This is for ASYNC connections. |
Connect Protocol | Connect protocol for the current session, which can be SYNC mode, ASYNC mode, ARA1.0, ARA2.0, LAP-M, MNP, FAX mode, SS7/COT, or V.110. |
Compression | Compression protocol used for the current connection, which can be None, V.42bis TX, V.42bis RX, V.42bis both, or MNP5 data compression. |
Count. Characters transmitted/received | Count of total characters received and transmitted for SYNC/ASYNC connections. |
Digital Pad | A digital pad can be implemented by the CO in order to attenuate a "hot" signal. Compensation boosts the signal the amount of the pad. Values can range from 0 to 7dB, with typical values being 0, 3, and 6dB. It is mandatory for K56Flex, but configurable for V.90 via S52. K56Flex only supports 0, 3, and 6 dB. V.90 supports steps of 1/8192 dB, but it is reported to the host insteps of 1/8 dB granularity. |
Digital Pad Compensation | Compensation of padding detected in the network. |
EC packets transmitted/received OK | EC packets transmitted is the number of TX frames that the client modem accepted. EC packets received is the number of data RX frames accepted. |
EC packets (Received BAD/ABORTED) | This is identical to EC Retransmission. |
EC Retransmission count | The number of times Nextport has gone into error recovery in the TX direction for a particular connection. The bigger the number, the worse the connection. However, this parameter should be weighed against the count produced by EC packets transmitted and received in order to determine if there should really be a concern. |
Far End Echo Level | Over long connections, an echo is produced by impedance mismatches at 2 wire to 4 wire as well as 4 wire to 2 wire hybrid circuitry. The far end echo level (that portion of the transmitted analog signal that has bounced off of the remote modem's analog front end) may range from 0 to -90 in dBm. |
Frequency Offset | It is the difference between the modulation carriers (frequency shift in the receive spectrum) between the expected RX carrier frequency and the actual RX carrier frequency. |
Link Signal Quality | Measure of line quality for a given bit rate where 0 is the worst and 3 is steady state. If a 1 or 2 is present, the modem must shift down to a lower rate. Likewise, if the Sq value is 4 to 7, the modem speeds shift up to a higher rate. If the Sq value is high (for example, 7) and the bit rate is low, then there may be a problem at the remote end receiver. |
Modulation Standard | Modulation standard that can be V.21, Bell03, V.22, V.22bis, Bell212, V.23, V.32, V.32bis, V.32terbo, V.34, V.34+, K56Flex, or V.90 |
Phase Jitter Frequency | Peak to peak differential between two signal points. Uncanceled phase jitter looks like "rocking" of the baseband QAM constellation. The points look like arcs with the outer points having longer arcs. |
Phase Jitter Level | Amount of phase jitter measured and indicates how large the "rocking" is in degrees. On an oscilloscope, the constellation points would look like crescent moons. Values can range up to 15 degrees. The typical value is zero (that is, phase jitter is not normally present). |
Phase Roll | Phase roll effects the echo signal coming back. A certain constellation pattern is transmitted from a modem and makes it to the central office. Some echoed form of this signal/constellation pattern is sent back. However, the constellation shape may be rotated from 0-359 degrees. This rotation is called the phase roll. |
PPP/SLIP packets transmitted/received | Total count of PPP/SLIP packets transmitted and received. This total could include all PPP/SLIP packets, including BAD/ABORTED packets. |
PPP/SLIP packets received (BAD/ABORTED) | Total count of the bad or aborted PPP/SLIP packets, which is a subset of PPP/SLIP packets received. A counted PPP packet has a bad FCS, or the SLIP packet has a transparency error. |
RBS Pattern | Reports the number of robbed bits detected in the connection. The robbed bits are used for inband signalling. This information is only reported for K56Flex (by the analog modem) and is only found on a channelized line such as T1 or E1. The 6 LSBs of the returned value indicate the periodic RBS pattern where a 1 denotes a pulse code modulation (PCM) sample with a robbed bit. |
Receive Level | This is the power of the received signal and ranges from 0 to -128 in dBm steps. Typically the range in the United States is about -22 dBm, and in Europe is -12 dBm. A good range is from -12dBm to -24dBm. |
Round Trip Delay | Total round trip propagation delay of the link (in milliseconds). This is important for proper echo cancellation. The amount that the delay varies on the network. |
Self Test Error count | Total errors generated during a self-test run. |
SNR | The ratio measurement of the desired signal to noise. This value can range from 0 to 70 dB and changes in 1 dB steps. Note that a 28.8kbps connection demands an SNR of about 37dB. Lower than this and the quality of the connection diminishes. A 33.6kbps connection demands an SNR of 38 to 39dB. Also note that a "clean" line has an SNR of about 41dB. |
Total Retrains | Count of total retrains and speed shifts. |
TX/RX Bit Rate | TX is the bit rate from the local DCE to the remote DCE. RX is the bit rate from the remote DCE to the local DCE. These rates may be asynchronous |
TX/RX Carrier Frequency | For TX, carrier frequency used by the local DCE. For RX, carrier frequency used by the remote DCE. |
TX/RX Symbol Rate | TX is symbol rate used to send samples to the line. RX is the symbol rate used to receive samples off of the line. The rates are synchronous with each other. |
TX/RX Trellis Coding | Adds dependency between symbols in order to make the detection in noise more robust (Forward Error Correction). Modems may use 8 (V.32, V.32bis, V.17), 16, 32, 64 (V.34, V.34+, V.90, K56flex), or no trellis coding (V.22, V.22bis, V.21, Bell212, Bell103, V.29, V.27). |
TX/RX Pre emphasis Index | Involves shaping the raw transmit spectrum in order to deal with spectrum roll-offs. The pre-emphasis index can take on the values 0 to 10. A zero denotes no reshaping. Typical values usually fall in the ranges 0 to 2 or 6 to 7. This technique is used with V.34 and V.34+ standards. |
TX/RX Constellation Shaping | A method for improving noise immunity by using a probability distribution for transmitted signal points. The signal states used to predict the sensitivity to certain transmission impairments. Values may be either none or active. This technique is used with V.34 and V.34+ standards. |
TX/RX Nonlinear Encoding | Occurs during the training phase and moves the constellation's outer points away in order to deal with nonlinear distortion. Nonlinear distortion (0-200Hz) tends to effect the higher power signals. Moving the outer constellation points out reduces the chance of error. Values may be either none or active. MICA modems support nonlinear coding in both directions. This technique is used with V.34 and V.34+ standards. |
TX/RX Precoding | Serves the same purpose as the pre-emphasis index but instead manages the bits and not the raw transmit signals. This is done only when asked and therefore will occur in the RX mode. The values may be either none or active. This technique is used with V.34 and V.34+ standards. |
TX/RX Xmit Level Reduction | Effects the transmit signal with 0 to 15 in dBm of reduction. If nonlinear distortion is detected, the modem prompts the client for a lower-powered TX signal. If the remote end detects nonlinear distortion, it may ask us to lower our TX signal. This technique is used with V.34 and V.34+ standards. |
Related Commands
port modem autotest Automatically and periodically performs a modem diagnostics test for modems inside the access server or router. port modem startup-test Performs diagnostic testing for all modems. show spe modem active Displays active modem statistics of all SPEs, a specified SPE, or the specified range of SPEs. test port modem back-to-back Connects two specified ports back-to-back and transfer a specified amount of data between the ports.
Command
Description
To show Service Processing Element (SPE) status, use the show spe EXEC command.
Cisco AS5400 with NextPort DFC
show spe [slot | slot/spe]
Cisco AS5800 with universal port card
show spe [shelf/slot | shelf/slot/spe]
Syntax Description s
slot (Optional) All ports on the specified slot. For the AS5400, slot values range from 0 to 7. slot/spe (Optional) All ports on the specified slot and SPE. For the AS5400, slot values range from 0 to 7 and SPE values range from 0 to 17. shelf/slot (Optional) All ports on the specified shelf and slot. For the AS5800, shelf values range from 0 to 1 and UPC slot values range from 2 to 11. shelf/slot/spe (Optional) All ports on the specified SPE. For the AS5800, shelf values range from 0 to 1, slot values range from 2 to 11, and SPE values range from 0 to 53.
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
12.1(1)XD This command was introduced on the Cisco AS5400. 12.1(3)T This command was supported on the Cisco AS5400 and Cisco AS5800.
Release
Modification
Usage Guidelines
Use the show spe command to display history statistics of all SPEs, a specified SPE, or the specified range of SPEs.
Examples
The following example displays history statistics for all SPEs after a busyout was executed on SPE 2/0 and a shutdown was executed on SPE 2/1 on the Cisco AS5400:
Router# show spe
SPE settings:
==============
Country code configuration: default T1 (u Law)
Polling interval: 12 secs.
History log events: 50(per port)
Port legends:
============
Port state: (s)shutdown (t)test (r)recovery (d)download
(b)busiedout (p)busyout pending, (B)bad (a)active call
Call Type: (m)modem (d)digital (_)not in use
SPE SPE SPE SPE Port Call
SPE# Port # State Busyout Shut Crash State Type
2/00 0000-0005 ACTIVE 0 0 0 aaaaaa dddddd
2/01 0006-0011 ACTIVE 0 0 0 aaaaaa dddddd
2/02 0012-0017 ACTIVE 0 0 0 aaaaaa dddddd
2/03 0018-0023 ACTIVE 0 0 0 aaaaaa dddmdm
2/04 0024-0029 ACTIVE 0 0 0 aaaaaa dmmmmm
2/05 0030-0035 ACTIVE 0 0 0 aaa_aa mmm_mm
2/06 0036-0041 ACTIVE 0 0 0 __aaaa __mmmm
2/07 0042-0047 ACTIVE 0 0 0 aaa_aa mmm_mm
2/08 0048-0053 ACTIVE 0 0 0 _aaa_a _mmm_m
2/09 0054-0059 ACTIVE 0 0 0 _aa_aa _md_mm
2/10 0060-0065 ACTIVE 0 0 0 _a_a_a _m_m_m
2/11 0066-0071 ACTIVE 0 0 0 _a_aaa _d_mmd
2/12 0072-0077 ACTIVE 0 0 0 aaaaaa mdmmmd
2/13 0078-0083 ACTIVE 0 0 0 _aaaaa _dmmdm
2/14 0084-0089 ACTIVE 0 0 0 _a_aaa _m_ddd
2/15 0090-0095 ACTIVE 0 0 0 a_aaaa m_dddd
2/16 0096-0101 ACTIVE 0 0 0 aaaaaa ddddmd
2/17 0102-0107 ACTIVE 0 0 0 aaaaaa dddddd
The following example shows output for the show spe command on the Cisco AS5800 with universal port card. This example shows SPE settings for slot 2, SPEs 0 to 53:
Router# show spe
SPE settings
==============
Country code configuration default T1 (u Law)
Polling interval 12 secs.
History log events 50(per port)
Port legends
============
Port state (s)shutdown (t)test (r)recovery (d)download
(b)busiedout (p)busyout pending, (B)bad (a)active call
Call type (m)modem (d)digital (_)not in use
SPE SPE SPE SPE Port Call
SPE# Port # State Busyout Shut Crash State Type
1/02/00 0000-0005 ACTIVE 0 0 0 a_a_a_ m_m_m_
1/02/01 0006-0011 ACTIVE 0 0 0 aaa___ mmm___
1/02/02 0012-0017 ACTIVE 0 0 0 _a_aa_ _m_mm_
1/02/03 0018-0023 ACTIVE 0 0 0 _aaaaa _mmmmm
1/02/04 0024-0029 ACTIVE 0 0 0 a_a_a_ m_m_m_
1/02/05 0030-0035 ACTIVE 0 0 0 ____a_ ____m_
1/02/06 0036-0041 ACTIVE 0 0 0 _aaa_a _mmm_m
1/02/07 0042-0047 ACTIVE 0 0 0 a_____ m_____
1/02/08 0048-0053 ACTIVE 0 0 0 _aa_aa _mm_mm
1/02/09 0054-0059 ACTIVE 0 0 0 _aa_aa _mm_mm
1/02/10 0060-0065 ACTIVE 0 0 0 _a_a_a _m_m_m
1/02/11 0066-0071 ACTIVE 0 0 0 a__aa_ m__mm_
1/02/12 0072-0077 ACTIVE 0 0 0 aaa___ mmm___
1/02/13 0078-0083 ACTIVE 0 0 0 aaaa_a mmmm_m
1/02/14 0084-0089 ACTIVE 0 0 0 _aaa__ _mmm__
1/02/15 0090-0095 ACTIVE 0 0 0 a__aaa m__mmm
1/02/16 0096-0101 ACTIVE 0 0 0 _aaaa_ _mmmm_
1/02/17 0102-0107 ACTIVE 0 0 0 _aaa_a _mmm_m
1/02/18 0108-0113 ACTIVE 1 0 0 _aaaaa _mmmmm
1/02/19 0114-0119 ACTIVE 1 0 0 aa_aa_ mm_mm_
1/02/20 0120-0125 ACTIVE 1 0 0 aa__aa mm__mm
1/02/21 0126-0131 ACTIVE 1 0 0 aaa_aa mmm_mm
1/02/22 0132-0137 ACTIVE 1 0 0 _a____ _m____
1/02/23 0138-0143 ACTIVE 1 0 0 a__aaa m__mmm
1/02/24 0144-0149 ACTIVE 1 0 0 a_a_aa m_m_mm
1/02/25 0150-0155 ACTIVE 1 0 0 ___aaa ___mmm
1/02/26 0156-0161 ACTIVE 1 0 0 a_a__a m_m__m
1/02/27 0162-0167 ACTIVE 1 0 0 a_a_aa m_m_mm
1/02/28 0168-0173 ACTIVE 1 0 0 a___aa m___mm
1/02/29 0174-0179 ACTIVE 1 0 0 _a____ _m____
1/02/30 0180-0185 ACTIVE 1 0 0 _aaaaa _mmmmm
1/02/31 0186-0191 ACTIVE 1 0 0 _a_aa_ _m_mm_
1/02/32 0192-0197 ACTIVE 1 0 0 aaa__a mmm__m
1/02/33 0198-0203 ACTIVE 1 0 0 a_a__a m_m__m
1/02/34 0204-0209 ACTIVE 1 0 0 aaaaaa mmmmmm
1/02/35 0210-0215 ACTIVE 1 0 0 _aa__a _mm__m
1/02/36 0216-0221 ACTIVE 0 0 0 a_a_aa m_m_mm
1/02/37 0222-0227 ACTIVE 0 0 0 a_aaaa m_mmmm
1/02/38 0228-0233 ACTIVE 0 0 0 aaaaaa mmmmmm
1/02/39 0234-0239 ACTIVE 0 0 0 aa_aa_ mm_mm_
1/02/40 0240-0245 ACTIVE 0 0 0 aa_aaa mm_mmm
1/02/41 0246-0251 ACTIVE 0 0 0 a__a__ m__m__
1/02/42 0252-0257 ACTIVE 0 0 0 aa__aa mm__mm
1/02/43 0258-0263 ACTIVE 0 0 0 aaa_aa mmm_mm
1/02/44 0264-0269 ACTIVE 0 0 0 aaaa_a mmmm_m
1/02/45 0270-0275 ACTIVE 0 0 0 aaa_a_ mmm_m_
1/02/46 0276-0281 ACTIVE 0 0 0 aaaaa_ mmmmm_
1/02/47 0282-0287 ACTIVE 0 0 0 _aaaa_ _mmmm_
1/02/48 0288-0293 ACTIVE 0 0 0 a_aa_a m_mm_m
1/02/49 0294-0299 ACTIVE 0 0 0 aa_a_a mm_m_m
1/02/50 0300-0305 ACTIVE 0 0 0 aa_aaa mm_mmm
1/02/51 0306-0311 ACTIVE 0 0 0 aaaaa_ mmmmm_
1/02/52 0312-0317 ACTIVE 0 0 0 aaaaaa mmmmmm
1/02/53 0318-0323 ACTIVE 0 0 0 aaaa_a mmmm_m
Related Commands
show spe modem active Displays active modem statistics of all SPEs, a specified SPE, or the specified range of SPEs. show spe digital active Displays active digital calls and digital statistics of all SPEs, a specified SPE, or the specified range of SPEs.
Command
Description
To display history statistics of all digital Service Processing Elements (SPEs), in summary form or for SPEs starting with a specified slot or a specified shelf/slot/range of SPEs, use the show spe digital EXEC command.
Cisco AS5400 with NextPort DFC
show spe digital [slot | slot/spe]
|
Note This command is not supported on the Cisco AS5800 with the universal port card. |
Syntax Description
slot (Optional) All ports on the specified slot. For the AS5400, slot values range from 0 to 7. slot/spe (Optional) All ports on the specified slot and SPE. For the AS5400, slot values range from 0 to 7 and SPE values range from 0 to 17.
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
12.1(1)XD This command was introduced on the Cisco AS5400. 12.1(3)T This command was supported on the Cisco AS5400.
Release
Modification
Usage Guidelines
The show spe digital command displays history statistics of all digital SPEs, in summary form or for SPEs starting with a specified slot, or a specified shelf/slot/range of SPEs.
Examples
The following example shows output for the show spe digital command on the Cisco AS5400 with NextPort DFC. This example shows statistics for slot 5, SPE 4:
Router# show spe digital 5/4
#SPE 5/04
Cisco Universal SPE; Fw: 0.06.07.03; Async5/24 - 5/29, TTY672 - 677
Last clearing of statistics counters : never
11 incoming completes 24 incoming failures
0 outgoing completes 0 outgoing failures
0 failed dial attempts 0 ring no answers
0 no dial tones 0 link failures
0 watchdog timeouts 0 protocol errors
0 dial timeouts
Transmit Speed Counters :
Speed Calls Speed Calls Speed Calls Speed Calls
Speed Calls
64000 0 28800 0 14400 0 7200 0
1200 0
56000 0 24000 0 12000 0 4800 1
600 0
38400 0 19200 10 9600 0 2400 0
Receive Speed Counters :
Speed Calls Speed Calls Speed Calls Speed Calls
Speed Calls
64000 0 28800 0 14400 0 7200 0
1200 0
56000 0 24000 0 12000 0 4800 1
600 0
38400 0 19200 10 9600 0 2400 0
Related Commands
show spe digital active Displays active digital calls and digital statistics of all SPEs, a specified SPE, or the specified range of SPEs. show spe digital csr Displays digital calls success rate (CSR) statistics of all SPEs, a specified SPE, or the specified range of SPEs. show spe digital disconnect-reason Displays the local disconnect reasons for all digital calls on the SPEs, a specified SPE, or the specified range of SPEs. show spe digital summary Displays history statistics of all SPEs, a specified SPE, or the specified range of SPEs.
Command
Description
To display active digital calls and digital statistics of all Service Processing Elements (SPEs), a specified SPE, or the specified range of SPEs, use the show spe digital active EXEC command.
Cisco AS5400 with NextPort DFC
show spe digital active [slot | slot/spe]
|
Note This command is not supported on the Cisco AS5800 with the universal port card. |
Syntax Description
slot (Optional) All ports on the specified slot. For the AS5400, slot values range from 0 to 7. slot/spe (Optional) All ports on the specified slot and SPE. For the AS5400, slot values range from 0 to 7 and SPE values range from 0 to 17.
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
12.1(1)XD This command was introduced on the Cisco AS5400. 12.1(3)T This command was supported on the Cisco AS5400
Release
Modification
Usage Guidelines
The show spe digital active command displays active digital calls and digital statistics of all SPEs, a specified SPE, or the specified range of SPEs.
Examples
The following example shows output for the show spe digital active command on the Cisco AS5400 with NextPort DFC. This example displays active digital statistics for slot 5, SPE 6:
Router# show spe digital active 5
SPE 5/06
Char Sync
Port Prot Duration Tx/Rx Cfg Loss
41 V.110 188 19200/19200 In 0
SPE 5/09
Char Sync
Port Prot Duration Tx/Rx Cfg Loss
54 V.110 187 19200/19200 In 0
56 V.110 187 19200/19200 In 0
57 V.110 188 19200/19200 In 0
...
Related Commands
show spe digital Displays history statistics of all digital SPEs, in summary form or for SPEs starting with a specified slot or a specified shelf/slot/range of SPEs. show spe digital csr Displays digital calls success rate (CSR) statistics of all SPEs, a specified SPE, or the specified range of SPEs. show spe digital disconnect-reason Displays the local disconnect reasons for all digital calls on the SPEs, a specified SPE, or the specified range of SPEs. show spe digital summary Display history statistics of all SPEs, a specified SPE, or the specified range of SPEs.
Command
Description
To display digital calls success rate (CSR) statistics of all Service Processing Elements (SPEs), a specified SPE, or the specified range of SPEs, use the show spe digital csr EXEC command.
Cisco AS5400 with NextPort DFC
show spe digital csr [summary | slot | slot/spe]
|
Note This command is not supported on the Cisco AS5800 with the universal port card. |
Syntax Description
summary (Optional) Summary digital CSR statistics. slot (Optional) All ports on the specified slot. For the AS5400, slot values range from 0 to 7. slot/spe (Optional) All ports on the specified slot and SPE. For the AS5400, slot values range from 0 to 7 and SPE values range from 0 to 17.
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
12.1(1)XD This command was introduced on the Cisco AS5400. 12.1(3)T This command was supported on the Cisco AS5400.
Release
Modification
Usage Guidelines
The show spe digital csr command displays digital calls success rate (CSR) statistics of all SPEs, a specified SPE, or the specified range of SPEs.
Examples
The following example shows output for the show spe digital csr command on the Cisco AS5400 with universal port card. This example displays the number of call success rate counters for slot 5:
Router# show spe digital csr 5
Avg Hold Inc calls Out calls Failed No Succ
SPE Time Succ Fail Succ Fail Dial Answer Pct
5/00 00:04:22 6 0 0 0 0 0 100%
5/01 00:04:22 6 0 0 0 0 0 100%
5/02 00:04:22 6 0 0 0 0 0 100%
5/03 00:04:22 6 0 0 0 0 0 100%
5/04 00:04:22 6 0 0 0 0 0 100%
5/05 00:04:21 6 0 0 0 0 0 100%
5/06 00:04:22 4 0 0 0 0 0 100%
5/07 00:04:22 1 0 0 0 0 0 100%
5/08 00:04:21 6 0 0 0 0 0 100%
5/09 00:04:23 5 0 0 0 0 0 100%
5/10 00:00:00 0 0 0 0 0 0 0%
5/11 00:04:21 5 0 0 0 0 0 100%
5/12 00:04:20 2 0 0 0 0 0 100%
5/13 00:00:00 0 0 0 0 0 0 0%
5/14 00:00:00 0 0 0 0 0 0 0%
5/15 00:00:00 0 0 0 0 0 0 0%
5/16 00:00:00 0 0 0 0 0 0 0%
5/17 00:00:00 0 0 0 0 0 0 0%
Related Commands
show spe digital Displays history statistics of all digital SPEs, in summary form or for SPEs starting with a specified slot or a specified shelf/slot/range of SPEs. show spe digital active Displays active digital calls and digital statistics of all SPEs, a specified SPE, or the specified range of SPEs. show spe digital disconnect-reason Displays the local disconnect reasons for all digital calls on the SPEs, a specified SPE, or the specified range of SPEs. show spe digital summary Displays history statistics of all SPEs, a specified SPE, or the specified range of SPEs.
Command
Description
To display the local disconnect reasons for all digital calls on the Service Processing Elements (SPEs), a specified SPE, or the specified range of SPEs, use the show spe digital disconnect-reason EXEC command.
Cisco AS5400 with NextPort DFC
show spe digital disconnect-reason [summary | slot | slot/spe]
|
Note This command is not supported on the Cisco AS5800 with the universal port card. |
Syntax Description
summary (Optional) Summary of local disconnect reasons for digital ports. slot (Optional) All ports on the specified slot. For the AS5400, slot values range from 0 to 7. slot/spe (Optional) All ports on the specified slot and SPE. For the AS5400, slot values range from 0 to 7 and SPE values range from 0 to 17.
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
12.1(1)XD This command was introduced on the Cisco AS5400. 12.1(3)T This command was supported on the Cisco AS5400.
Release
Modification
Usage Guidelines
The show spe digital disconnect-reason command displays the local disconnect reasons for all digital calls on the SPEs, a specified SPE, or the specified range of SPEs.
Examples
The following example shows output for the show spe digital disconnect-reason command on the Cisco AS5400 with NextPort DFC. This example displays reasons for digital call disconnects on slot 5:
Router# show spe digital disconnect-reason 5 #SPE 5/00 : =====CLASS HOST====== =====CLASS SERVICE===== NonSpecific 0 ATH 0 Busy 0 Aborted 0 No Answer 0 Connect Timeout 0 DTR 0 Sync Loss 0 ATH 0 NoDialTone 0 No Carrier 0 ACK 0 TOTAL 0 #SPE 5/03 : =====CLASS HOST====== =====CLASS SERVICE===== NonSpecific 0 ATH 0 Busy 1 Aborted 0 No Answer 0 Connect Timeout 0 DTR 0 Sync Loss 0 ...
Related Commands
show spe digital active Displays active digital calls and digital statistics of all SPEs, a specified SPE, or the specified range of SPEs. show spe digital csr Displays digital calls success rate (CSR) statistics of all SPEs, a specified SPE, or the specified range of SPEs. show spe digital Displays history statistics of all digital SPEs, in summary form or for SPEs starting with a specified slot or a specified shelf/slot/range of SPEs. show spe digital summary Displays history statistics of all SPEs, a specified SPE, or the specified range of SPEs.
Command
Description
To display history statistics of all Service Processing Elements (SPEs), a specified SPE, or the specified range of SPEs, use the show spe digital summary EXEC command.
Cisco AS5400 with NextPort DFC
show spe digital summary [slot | slot/spe]
|
Note This command is not supported on the Cisco AS5800 with the universal port card. |
Syntax Description
slot (Optional) All ports on the specified slot. For the AS5400, slot values range from 0 to 7. slot/spe (Optional) All ports on the specified slot and SPE. For the AS5400, slot values range from 0 to 7 and SPE values range from 0 to 17.
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
12.1(1)XD This command was introduced on the Cisco AS5400. 12.1(3)T This command was supported on the Cisco AS5400.
Release
Modification
Usage Guidelines
The show spe digital summary command displays history statistics of all SPEs, a specified SPE, or the specified range of SPEs.
Examples
The following example shows output for the show spe digital summary command on the Cisco AS5400 with NextPort DFC. This example displays active digital statistics for slot 5:
Router# show spe digital summary 5
Async5/00 - 5/107, TTY648 - 755
209 incoming completes 397 incoming failures
0 outgoing completes 0 outgoing failures
0 failed dial attempts 0 ring no answers
0 no dial tones 0 link failures
0 watchdog timeouts 0 protocol errors
0 dial timeouts
Transmit Speed Counters :
Speed Calls Speed Calls Speed Calls Speed Calls
Speed Calls
64000 0 28800 0 14400 0 7200 0
1200 20
56000 0 24000 0 12000 0 4800 20
600 20
38400 0 19200 149 9600 0 2400 0
Receive Speed Counters :
Speed Calls Speed Calls Speed Calls Speed Calls
Speed Calls
64000 0 28800 0 14400 0 7200 0
1200 20
56000 0 24000 0 12000 0 4800 20
600 20
38400 0 19200 149 9600 0 2400 0
.
.
.
Related Commands
show spe digital active Displays active digital calls and digital statistics of all SPEs, a specified SPE, or the specified range of SPEs. show spe digital csr Displays digital calls success rate (CSR) statistics of all SPEs, a specified SPE, or the specified range of SPEs. show spe digital disconnect-reason Displays the local disconnect reasons for all digital calls on the SPEs, a specified SPE, or the specified range of SPEs. show spe digital Displays history statistics of all digital SPEs, in summary form or for SPEs starting with a specified slot or a specified shelf/slot/range of SPEs.
Command
Description
To display the Service Processing Element (SPE) system log, use the show spe log EXEC command.
Cisco AS5400 with NextPort DFC
show spe log [reverse | slot]
Cisco AS5800 with universal port card
show spe log [reverse | shelf/slot]
Syntax Description
reverse (Optional) Displays the SPE system log with the most recent event first. slot (Optional) All ports on the specified slot. For the AS5400, slot values range from 0 to 7. shelf/slot (Optional) All ports on the specified shelf and slot. For the AS5800, shelf values range from 0 to 1 and UPC slot values range from 2 to 11.
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
12.1(1)XD This command was introduced on the Cisco AS5400. 12.1(3)T This command was supported on the Cisco AS5400 and Cisco AS5800.
Release
Modification
Usage Guidelines
The show spe log command displays the slot history event log.
Examples
The following example shows output for the show spe log command on the Cisco AS5400 with NextPort DFC:
Router# show spe log
Slot 3 Events Log
2d15h : SPE State Event:
Address: 0x3000000
SPE : 3/00
Command: SPE_IMMEDIATE_DISABLE Complete
2d14h : SPE State Event:
Address: 0x3000100
SPE : 3/06
Command: SPE_IMMEDIATE_DISABLE Complete
2d13h : SPE State Event:
Address: 0x3000200
SPE : 3/12
Command: SPE_IMMEDIATE_DISABLE Complete
00:00:26: SPE State Event:
Address: 0x3000001
SPE : 3/01
Command: SPE_IMMEDIATE_DISABLE Complete
Slot 4 Events Log
2d13h : SPE State Event:
Address: 0x4000000
SPE : 4/00
Command: SPE_IMMEDIATE_DISABLE Complete
Slot 7 Events Log
2d15h : Diag Post event:
Address : 0x7000204
SPE : 7/16
Result : SPE_POST_TEST_FAILED
Test ID : SPE_POWER_ON_SELF_TEST
Diag Code : 0xFE01C004
Data Format: ASCII
Data Len : 0
Related Commands
clear spe log Clears all event entries in the slot history event log. show spe log reverse Displays the slot history event log, with most recent event first.
Command
Description
To display the modem service history statistics for specified Service Processing Element (SPE), use the show spe modem EXEC command.
Cisco AS5400 with NextPort DFC
show spe modem {slot | slot/spe}
Cisco AS5800 with universal port card
show spe modem {shelf/slot | shelf/slot/spe}
Syntax Description
slot (Optional) All ports on the specified slot. For the AS5400, slot values range from 0 to 7. slot/spe (Optional) All ports on the specified slot and SPE. For the AS5400, slot values range from 0 to 7 and SPE values range from 0 to 17. shelf/slot (Optional) All ports on the specified shelf and slot. For the AS5800, shelf values range from 0 to 1 and UPC slot values range from 2 to 11. shelf/slot/spe (Optional) All ports on the specified SPE. For the AS5800, shelf values range from 0 to 1, slot values range from 2 to 11, and SPE values range from 0 to 53.
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
12.1(1)XD This command was introduced on the Cisco AS5400. 12.1(3)T This command was supported on the Cisco AS5400 and Cisco AS5800.
Release
Modification
Usage Guidelines
The show spe modem command displays the modem service history statistics for a specified SPE.
Examples
The following example shows output for the show spe modem command on the Cisco AS5400 with NextPort DFC:
Router# show spe modem
Async1/2/00 - 1/3/323, TTY972 - 1619
4819 incoming completes 287 incoming failures
0 outgoing completes 0 outgoing failures
0 failed dial attempts 0 ring no answers 0 autotests
0 no carriers 11 dial timeouts 0
autotest fails
0 no dial tones 0 link failures 0 fail count
0 watchdog timeouts 2784 protocol errors 0 recovers
Transmit Speed Counters
Speed Calls Speed Calls Speed Calls Speed Calls Speed Calls 60000 0 48000 431 38400 0 30666 0 12000 143 58000 0 46666 0 38000 4 29333 0 9600 5 56000 15 46000 56 37333 110 28800 700 7200 11 54666 0 45333 299 36000 84 28000 5 4800 2 54000 0 44000 226 34666 0 26400 266 2400 0 53333 122 42666 0 34000 39 24000 46 1200 3 52000 562 42000 68 33600 323 21600 27 300 0 50666 0 41333 38 33333 9 19200 38 50000 59 40000 65 32000 20 16800 12 49333 370 38666 0 31200 653 14400 5
Receive Speed Counters
Speed Calls Speed Calls Speed Calls Speed Calls Speed Calls 38400 0 26400 2280 16800 11 7200 1 300 2 33600 113 24000 266 14400 139 4800 1 31200 215 21600 56 12000 4 2400 3 28800 1665 19200 47 9600 16 1200 0.
The following example shows output for the show spe modem command on the Cisco AS5800 with universal port card:
Router# show spe modem 1/8/0
#SPE 1/08/00
Cisco Universal SPE; Fw: 0.00.06.81; Async1/8/00 - 1/8/05, TTY2916 - 2921
Last clearing of statistics counters : never
90 incoming completes 0 incoming failures
0 outgoing completes 0 outgoing failures
0 failed dial attempts 0 ring no answers 0 autotests
0 no carriers 0 dial timeouts 0 autotest fails
0 no dial tones 0 link failures 0 fail count
0 watchdog timeouts 0 protocol errors
Transmit Speed Counters :
Speed Calls Speed Calls Speed Calls Speed Calls Speed Calls
60000 0 48000 0 38400 0 30666 0 12000 0
58000 0 46666 0 38000 0 29333 0 9600 0
56000 0 46000 0 37333 0 28800 0 7200 0
54666 0 45333 0 36000 0 28000 0 4800 0
54000 0 44000 0 34666 0 26400 0 2400 0
53333 0 42666 0 34000 0 24000 0 1200 0
52000 0 42000 0 33600 0 21600 0 300 0
50666 0 41333 0 33333 0 19200 0
50000 0 40000 0 32000 0 16800 0
49333 0 38666 0 31200 90 14400 0
Receive Speed Counters :
Speed Calls Speed Calls Speed Calls Speed Calls Speed Calls
38400 0 26400 0 16800 0 7200 0 300 0
33600 11 24000 0 14400 0 4800 0
31200 25 21600 0 12000 0 2400 0
28800 54 19200 0 9600 0 1200 0
Related Commands
show spe Displays history statistics of all SPEs, a specified SPE, or the specified range of SPEs.
Command
Description
To display statistics of all active calls on specified Service Processing Elements (SPEs), use the show spe modem active EXEC command.
Cisco AS5400 with NextPort DFC
show spe modem active {slot | slot/spe}
Cisco AS5800 with universal port card
show spe modem active {shelf/slot | shelf/slot/spe}
Syntax Description
slot All ports on the specified slot. For the AS5400, slot values range from 0 to 7. slot/spe All ports on the specified slot and SPE. For the AS5400, slot values range from 0 to 7 and SPE values range from 0 to 17. shelf/slot All ports on the specified shelf and slot. For the AS5800, shelf values range from 0 to 1 and UPC slot values range from 2 to 11. shelf/slot/spe All ports on the specified SPE. For the AS5800, shelf values range from 0 to 1, slot values range from 2 to 11, and SPE values range from 0 to 53.
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
12.1(1)XD This command was introduced on the Cisco AS5400. 12.1(3)T This command was supported on the Cisco AS5400 and Cisco AS5800.
Release
Modification
Examples
The following example shows output for the show spe modem active command on the Cisco AS5400 with NextPort DFC.This example displays active modem statistics for slot 5, SPE 6:
Router# show spe modem active 5/6 SPE 5/06 Port Type Prot Comp Duration Tx/Rx Tx/Rx(Lvl) SNR Cfg Retrain 37 V.90 LAP-M V.42bis 95 3890/76 --/-11 38 In 0
The following example shows output for the show spe modem active command on the Cisco AS5800 with universal port card. This example displays active modem statistics for shelf 1, slot 8:
Router# show spe modem active 1/8 SPE 1/08/34 Port Type Prot Comp Duration Tx/Rx(bps) Tx/Rx(Lvl) SNR Cfg Retrain 209 V.34+ LAP-M V.42bis 23 28800/31200 --/-13 37 In 0 SPE 1/08/35 Port Type Prot Comp Duration Tx/Rx(bps) Tx/Rx(Lvl) SNR Cfg Retrain 215 V.34+ LAP-M V.42bis 12 28800/31200 --/-13 37 In 0 SPE 1/08/36 Port Type Prot Comp Duration Tx/Rx(bps) Tx/Rx(Lvl) SNR Cfg Retrain 216 V.34+ LAP-M V.42bis 24 33600/31200 --/-36 38 In 0 217 ## ## ## 0 33600/300 --/19 37 In 0 218 ## ## ## 0 33600/300 --/19 37 In 0 219 ## ## ## 0 33600/300 --/19 35 In 0 ÿÿÿ
Related Commands
show port operational-status Displays the operational status of a specific port or port range. show spe Displays history statistics of all SPEs, a specified SPE, or the specified range of SPEs.
Command
Description
To display the call success rate for the specified Service Processing Elements (SPEs), use the show spe modem csr EXEC command.
Cisco AS5400 with NextPort DFC
show spe modem csr {summary | slot | slot/spe}
Cisco AS5800 with universal port card
show spe modem csr {summary | shelf/slot | shelf/slot/spe}
Syntax Description
summary Shows all call success rate statistics for all SPEs. slot All ports on the specified slot. For the AS5400, slot values range from 0 to 7. slot/spe All ports on the specified slot and SPE. For the AS5400, slot values range from 0 to 7 and SPE values range from 0 to 17. shelf/slot All ports on the specified shelf and slot. For the AS5800, shelf values range from 0 to 1 and UPC slot values range from 2 to 11. shelf/slot/spe All ports on the specified SPE. For the AS5800, shelf values range from 0 to 1, slot values range from 2 to 11, and SPE values range from 0 to 53.
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
12.1(1)XD This command was introduced on the Cisco AS5400. 12.1(3)T This command was supported on the Cisco AS5400 and Cisco AS5800.
Release
Modification
Usage Guidelines
The show spe modem csr command displays the modem call success rate statistics for a specific SPE, range of SPEs, or all the SPEs. The summary keyword displays the call success rate statistics for all SPEs.
Examples
The following example shows output for the show spe modem csr summary command on the Cisco AS5400 with NextPort DFC:
Router# show spe modem csr 5/6
Avg Hold Inc calls Out calls Failed No Succ
SPE Time Succ Fail Succ Fail Dial Answer Pct
5/06 00:22:41 2 0 0 0 0 0 100%
Router# show spe modem csr 5/1 5/6
Avg Hold Inc calls Out calls Failed No Succ
SPE Time Succ Fail Succ Fail Dial Answer Pct
5/01 00:00:00 0 0 0 0 0 0 0%
5/02 00:00:00 0 0 0 0 0 0 0%
5/03 00:00:00 0 0 0 0 0 0 0%
5/04 00:00:00 0 0 0 0 0 0 0%
5/05 00:00:00 0 0 0 0 0 0 0%
5/06 00:22:48 2 0 0 0 0 0 100%
The following example shows output for the show spe modem csr summary command on the Cisco AS5800 with universal port card:
Router# show spe modem csr summary Avg Hold Inc calls Out calls Failed No Succ Time Succ Fail Avail Succ Fail Avail Dial Answer Pct 002631 4827 285 93 0 0 93 5 0 94%
Related Commands
show spe modem summary Displays summary of modem statistics for the specified SPE or range of SPEs. show spe Displays history statistics of all SPEs, a specified SPE, or the specified range of SPEs.
Command
Description
To display all modem disconnect reasons for the specified Service Processing Element (SPE), use the show spe modem disconnect-reason EXEC command.
Cisco AS5400 with NextPort DFC
show spe modem disconnect-reason {summary | slot | slot/spe}
Cisco AS5800 with universal port card
show spe modem disconnect-reason {summary | shelf/slot | shelf/slot/spe}
Syntax Description
summary Shows the disconnect reasons for all SPEs. slot All ports on the specified slot. For the AS5400, slot values range from 0 to 7. slot/spe All ports on the specified slot and SPE. For the AS5400, slot values range from 0 to 7 and SPE values range from 0 to 17. shelf/slot All ports on the specified shelf and slot. For the AS5800, shelf values range from 0 to 1 and UPC slot values range from 2 to 11. shelf/slot/spe All ports on the specified SPE. For the AS5800, shelf values range from 0 to 1, slot values range from 2 to 11, and SPE values range from 0 to 53.
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
12.1(1)XD This command was introduced on the Cisco AS5400. 12.1(3)T This command was supported on the Cisco AS5400 and Cisco AS5800.
Release
Modification
Usage Guidelines
Disconnect reasons are reasons why active calls are disconnected. The disconnect reasons are displayed with Class boundaries.
Examples
The following example shows output for the show spe modem disconnect-reason summary command on the Cisco AS5400 with NextPort DFC:
Router# show spe modem disconnect-reason 5/6
#SPE 5/06 :
===CLASS OTHER==== =====CLASS DSP==== ===CLASS EC LCL=== ==CLASS EC FRMR===
Software Rst 0 No Carrier 0 No LR 0 Frmr Bad Cmd 0
EC Termntd 0 No ABT dtctd 0 LR Param1 0 Frmr Data 0
Bad MNP5 Rx 0 Trainup flr 0 LR Incmpt 0 Frmr Length 0
Bad V42B 0 Retrain Lt 0 Retrns Lt 0 Frmr Bad NR 0
Bad COP stat 0 ABT end flr 0 Inactivity 0
ATH 0 Protocol Err 0 ===CLASS EC LD====
Aborted 0 ====CLASS HOST==== Fallbck Term 0 LD No LR 0
Connect Tout 0 Hst NonSpec 0 No XID 0 LD LR Param1 0
Reset DSP 0 Hst Busy 0 XID Incmpt 0 LD LR Incmpt 0
Hst No answr 0 Disc 0 LD Retrns Lt 0
===CLASS EC Cmd=== Hst DTR 1 DM 0 LD Inactivty 0
Bad Cmd 0 Hst ATH 0 Bad NR 0 LD Protocol 0
Hst NoDialTn 0 SABME Online 0 LD User 0
=====N O N E====== Hst No Carr 0 XID Online 0
None 0 Hst Ack 0 LR Online 0 TOTAL 1
The following example shows the output for the show spe modem disconnect-reason command on the Cisco AS5800 with universal port card:
Router# show spe modem disconnect-reason
===CLASS OTHER==== =====CLASS DSP==== ===CLASS EC LCL=== ==CLASS EC FRMR===
Software Rst 0 No Carrier 21 No LR 0 Frmr Bad Cmd 0
EC Termntd 0 No ABT dtctd 0 LR Param1 0 Frmr Data 0
Bad MNP5 Rx 0 Trainup flr 26 LR Incmpt 0 Frmr Length 0
Bad V42B 12 Retrain Lt 0 Retrns Lt 37 Frmr Bad NR 0
Bad COP stat 0 ABT end flr 0 Inactivity 0
ATH 0 Protocol Err 5 ===CLASS EC LD====
Aborted 0 ====CLASS HOST==== Fallbck Term 22 LD No LR 0
Connect Tout 11 Hst NonSpec 799 No XID 5 LD LR Param1 0
Reset DSP 0 Hst Busy 0 XID Incmpt 0 LD LR Incmpt 0
Hst No answr 0 Disc 2718 LD Retrns Lt 0
===CLASS EC Cmd=== Hst DTR 870 DM 0 LD Inactivty 0
Bad Cmd 0 Hst ATH 0 Bad NR 0 LD Protocol 0
Hst NoDialTn 0 SABME Online 0 LD User 0
=====N O N E====== Hst No Carr 0 XID Online 0
None 29 Hst Ack 0 LR Online 0 TOTAL 4555
Related Commands
show spe Displays history statistics of all SPEs, a specified SPE, or the specified range of SPEs. show spe modem summary Displays summary of modem statistics for the specified SPE or range of SPEs.
Command
Description
To display the total number of connections within each modulization or codec for a specific range of Service Processing Elements (SPEs), use the show spe modem high speed EXEC command.
Cisco AS5400 with NextPort DFC
show spe modem high speed {summary | slot | slot/spe}
Cisco AS5800 with universal port card
show spe modem high speed {summary | shelf/slot | shelf/slot/spe}
Syntax Description
summary Shows a brief list of all modulation connections negotiated. slot All ports on the specified slot. For the AS5400, slot values range from 0 to 7. slot/spe All ports on the specified slot and SPE. For the AS5400, slot values range from 0 to 7 and SPE values range from 0 to 17. shelf/slot All ports on the specified shelf and slot. For the AS5800, shelf values range from 0 to 1 and UPC slot values range from 2 to 11. shelf/slot/spe All ports on the specified SPE. For the AS5800, shelf values range from 0 to 1, slot values range from 2 to 11, and SPE values range from 0 to 53.
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
12.1(1)XD This command was introduced on the Cisco AS5400. 12.1(3)T This command was supported on the Cisco AS5400 and Cisco AS5800.
Release
Modification
Examples
The following example shows output for the show spe modem high speed command on the Cisco AS5400 with NextPort DFC:
Router# show spe modem high speed #SPE 1/0 : Modln V.FC V.34 K56Flex V.90 Modln Speed Tx Rx Tx Rx Tx Rx Tx Rx Speed 56000 ------ ------ ------ ------ 000000 ------ 000000 ------ 56000 54667 ------ ------ ------ ------ - - 0 - 54667 54000 ------ ------ ------ ------ 0 - - - 54000 53333 ------ ------ ------ ------ - - 0 - 53333 52000 ------ ------ ------ ------ 0 - 0 - 52000 50667 ------ ------ ------ ------ - - 0 - 50667 50000 ------ ------ ------ ------ 0 - - - 50000 49333 ------ ------ ------ ------ - - 0 - 49333 48000 ------ ------ ------ ------ 0 - 0 - 48000 46667 ------ ------ ------ ------ - - 0 - 46667 46000 ------ ------ ------ ------ 0 - - - 46000 45333 ------ ------ ------ ------ - - 0 - 45333 44000 ------ ------ ------ ------ 0 - 0 - 44000 42667 ------ ------ ------ ------ - - 0 - 42667 42000 ------ ------ ------ ------ 0 - - - 42000 41333 ------ ------ ------ ------ - - 0 - 41333 40000 ------ ------ ------ ------ 0 - 0 - 40000 38667 ------ ------ ------ ------ - - 0 - 48667 38000 ------ ------ ------ ------ 0 - - - 38000 37333 ------ ------ ------ ------ - - 0 - 37333 36000 ------ ------ ------ ------ 0 - 0 - 36000 34667 ------ ------ ------ ------ - - 0 - 34667 34000 ------ ------ ------ ------ 0 - - - 34000 33600 ------ ------ 0 0 - - - 0 33600 33333 ------ ------ - - - - 0 - 33333 32000 ------ ------ - - 0 - 0 - 32000 31200 ------ ------ 0 0 - 0 - 0 31200 30667 ------ ------ - - - - 0 - 30667 29333 ------ ------ - - - - 0 - 29333 28800 0 0 0 0 - 0 - 0 28800 28000 - - - - - - 0 - 28000 26400 0 0 0 0 - 0 - 0 26400 24000 0 0 0 0 - 0 - 0 24000 21600 0 0 0 0 - 0 - 0 21600 19200 0 0 0 0 - 0 - 0 19200 16800 0 0 0 0 - 0 - 0 16800 14400 0 0 0 0 - 0 - 0 14400 12000 - - 0 0 - 0 - 0 12000 9600 - - 0 0 - 0 - 0 9600 7200 - - 0 0 - 0 - 0 7200 4800 - - 0 0 - 0 - 0 4800 2400 - - 0 0 - - - - 2400 TOTAL 0000000 0000000 0000000 0000000 TOTAL #SPE 1/1 : Modln V.FC V.34 K56Flex V.90 Modln Speed Tx Rx Tx Rx Tx Rx Tx Rx Speed 56000 ------ ------ ------ ------ 000000 ------ 000000 ------ 56000 54667 ------ ------ ------ ------ - - 0 - 54667 54000 ------ ------ ------ ------ 0 - - - 54000 53333 ------ ------ ------ ------ - - 0 - 53333 52000 ------ ------ ------ ------ 0 - 0 - 52000 50667 ------ ------ ------ ------ - - 0 - 50667 50000 ------ ------ ------ ------ 0 - - - 50000 49333 ------ ------ ------ ------ - - 0 - 49333 48000 ------ ------ ------ ------ 0 - 0 - 48000 46667 ------ ------ ------ ------ - - 0 - 46667 46000 ------ ------ ------ ------ 0 - - - 46000 45333 ------ ------ ------ ------ - - 0 - 45333 44000 ------ ------ ------ ------ 0 - 0 - 44000 42667 ------ ------ ------ ------ - - 0 - 42667 42000 ------ ------ ------ ------ 0 - - - 42000 41333 ------ ------ ------ ------ - - 0 - 41333 40000 ------ ------ ------ ------ 0 - 0 - 40000 38667 ------ ------ ------ ------ - - 0 - 48667 38000 ------ ------ ------ ------ 0 - - - 38000 37333 ------ ------ ------ ------ - - 0 - 37333 36000 ------ ------ ------ ------ 0 - 0 - 36000 34667 ------ ------ ------ ------ - - 0 - 34667 34000 ------ ------ ------ ------ 0 - - - 34000 33600 ------ ------ 0 0 - - - 0 33600 33333 ------ ------ - - - - 0 - 33333 32000 ------ ------ - - 0 - 0 - 32000 31200 ------ ------ 0 0 - 0 - 0 31200 30667 ------ ------ - - - - 0 - 30667 29333 ------ ------ - - - - 0 - 29333 28800 0 0 0 0 - 0 - 0 28800 28000 - - - - - - 0 - 28000 26400 0 0 0 0 - 0 - 0 26400 24000 0 0 0 0 - 0 - 0 24000 21600 0 0 0 0 - 0 - 0 21600 19200 0 0 0 0 - 0 - 0 19200 16800 0 0 0 0 - 0 - 0 16800 14400 0 0 0 0 - 0 - 0 14400 12000 - - 0 0 - 0 - 0 12000 9600 - - 0 0 - 0 - 0 9600 7200 - - 0 0 - 0 - 0 7200 4800 - - 0 0 - 0 - 0 4800 2400 - - 0 0 - - - - 2400 TOTAL 0000000 0000000 0000000 0000000 TOTAL .
The following example shows output for the show spe modem high speed command on the Cisco AS5800 with universal port card:
Router# show spe modem high speed 1/8/1
-- Indicates an invalid speed for a standard
#SPE 1/08/01 :
Modln V.FC V.34 K56Flex V.90 Modln
Speed Tx Rx Tx Rx Tx Rx Tx Rx Speed
60000 ------ ------ ------ ------ 000000 ------ ------ ------ 60000
58000 ------ ------ ------ ------ 0 ------ ------ ------ 58000
56000 ------ ------ ------ ------ 0 - 0 - 56000
54667 ------ ------ ------ ------ - - 0 - 54667
54000 ------ ------ ------ ------ 0 - - - 54000
53333 ------ ------ ------ ------ - - 0 - 53333
52000 ------ ------ ------ ------ 0 - 0 - 52000
50667 ------ ------ ------ ------ - - 0 - 50667
50000 ------ ------ ------ ------ 0 - - - 50000
49333 ------ ------ ------ ------ - - 0 - 49333
48000 ------ ------ ------ ------ 0 - 0 - 48000
46667 ------ ------ ------ ------ - - 0 - 46667
46000 ------ ------ ------ ------ 0 - - - 46000
45333 ------ ------ ------ ------ - - 0 - 45333
44000 ------ ------ ------ ------ 0 - 0 - 44000
42667 ------ ------ ------ ------ - - 0 - 42667
42000 ------ ------ ------ ------ 0 - - - 42000
41333 ------ ------ ------ ------ - - 0 - 41333
40000 ------ ------ ------ ------ 0 - 0 - 40000
38667 ------ ------ ------ ------ - - 0 - 38667
38400 ------ ------ ------ ------ - - - - 38400
38000 ------ ------ ------ ------ 0 - - - 38000
37333 ------ ------ ------ ------ - - 0 - 37333
36000 ------ ------ ------ ------ 0 - 0 - 36000
34666 ------ ------ ------ ------ - - 0 - 34666
34000 ------ ------ ------ ------ 0 - - - 34000
33600 ------ ------ 0 1 - - - 0 33600
33333 ------ ------ - - - - 0 - 33333
32000 ------ ------ - - 0 - 0 - 32000
31200 ------ ------ 6 1 - 0 - 0 31200
30667 ------ ------ - - - - 0 - 30667
29333 ------ ------ - - - - 0 - 29333
28800 0 0 0 4 - 0 - 0 28800
28000 - - - - - - 0 - 28000
26400 0 0 0 0 - 0 - 0 26400
24000 0 0 0 0 - 0 - 0 24000
21600 0 0 0 0 - 0 - 0 21600
19200 0 0 0 0 - 0 - 0 19200
16800 0 0 0 0 - 0 - 0 16800
14400 0 0 0 0 - 0 - 0 14400
12000 - - 0 0 - 0 - 0 12000
9600 - - 0 0 - 0 - 0 9600
7200 - - 0 0 - 0 - 0 7200
4800 - - 0 0 - 0 - 0 4800
2400 - - 0 0 - - - - 2400
TOTAL 0000000 0000012 0000000 0000000
Related Commands
show spe modem low speed Displays the connect-speeds within each low-speed modulation or codec for the specified Service Processing Elements (SPEs).
Command
Description
To display the total number of connections within each high modulation or codec for a specific range of Service Processing Element (SPE), use the show spe modem high standard EXEC command.
Cisco AS5400 with NextPort DFC
show spe modem high standard {summary | slot | slot/spe}
Cisco AS5800 with universal port card
show spe modem high standard {summary | shelf/slot | shelf/slot/spe}
Syntax Description
summary Shows a brief list of all modulation connections negotiated. slot All ports on the specified slot. For the AS5400, slot values range from 0 to 7. slot/spe All ports on the specified slot and SPE. For the AS5400, slot values range from 0 to 7 and SPE values range from 0 to 17. shelf/slot All ports on the specified shelf and slot. For the AS5800, shelf values range from 0 to 1 and UPC slot values range from 2 to 11. shelf/slot/spe All ports on the specified SPE. For the AS5800, shelf values range from 0 to 1, slot values range from 2 to 11, and SPE values range from 0 to 53.
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
12.1(1)XD This command was introduced on the Cisco AS5400. 12.1(3)T This command was supported on the Cisco AS5400 and Cisco AS5800.
Release
Modification
Examples
The following example shows output for the show spe modem high standard command on the Cisco AS5400 with NextPort DFC. This example displays standard low-speed connections for SPEs in slot 5: Router# show spe modem high standard 5 SPE/Mod-> V.FC V.34 K56Flex V.90 5/00 0 1 2 1 5/01 0 0 0 0 5/02 0 0 0 0 5/03 0 0 0 0 5/04 0 0 0 0 5/05 0 0 0 0 5/06 0 0 0 2 5/07 0 0 0 0 5/08 0 0 0 0 5/09 0 0 0 0 5/10 0 0 0 0 5/11 0 0 0 0 5/12 0 0 0 0 5/13 0 0 0 0 5/14 0 0 0 0 5/15 0 0 0 0 5/16 0 0 0 0 5/17 0 0 0 0 TOTAL 00000000 00000001 00000002 00000003 The following example shows output for the show spe modem high standard command on the Cisco AS5800 with universal port card. This example displays standard low-speed connections for SPEs in slot 8: Router# show spe modem high standard 1/8/1 SPE/Mod-> V.FC V.34 K56Flex V.90 1/08/01 0 6 0 0 TOTAL 00000000 00000006 00000000 00000000
Related Commands TOTAL 00000 00000 00000 00000 00000 00000 00000 00000 00000 00000 00000
show spe modem low standard Displays the connect-speeds within each low-speed modulation or codec for the SPE.
Command
Description
To display the connect-speeds within each low-speed modulation or codec for the specified Service Processing Elements (SPEs), use the show spe modem low speed EXEC command.
Cisco AS5400 with NextPort DFC
show spe modem low speed {summary | slot | slot/spe}
Cisco AS5800 with universal port card
show spe modem low speed {summary | shelf/slot | shelf/slot/spe}
Syntax Description
summary Shows a brief list of all modulation connections negotiated. slot (Optional) All ports on the specified slot. For the AS5400, slot values range from 0 to 7. slot/spe (Optional) All ports on the specified slot and SPE. For the AS5400, slot values range from 0 to 7 and SPE values range from 0 to 17. shelf/slot (Optional) All ports on the specified shelf and slot. For the AS5800, shelf values range from 0 to 1 and UPC slot values range from 2 to 11. shelf/slot/spe (Optional) All ports on the specified SPE. For the AS5800, shelf values range from 0 to 1, slot values range from 2 to 11, and SPE values range from 0 to 53.
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
12.1(1)XD This command was introduced on the Cisco AS5400. 12.1(3)T This command was supported on the Cisco AS5400 and Cisco AS5800.
Release
Modification
Examples
The following example shows output for the show spe modem low speed command on the Cisco AS5400 with NextPort DFC. This example displays standard low-speed connections: Router# show spe modem low speed #SPE 1/0 : <-- MODEM FAX --> Speed B103 V.21 B212 V.22 V.22b V.32 V.32b V.27t V.29 V.17 14400 ------ ------ ------ ------ ------ ------ 30 ------ ------ 0 12000 ------ ------ ------ ------ ------ ------ 0 ------ ------ 0 9600 ------ ------ ------ ------ ------ 0 0 ------ 0 0 7200 ------ ------ ------ ------ ------ - 0 ------ 0 0 4800 ------ ------ ------ ------ ------ 0 0 0 0 ------ 2400 ------ ------ ------ ------ 0 ------ ------ 0 ------ ------ 1200 ------ ------ 0 0 6 ------ ------ ------ ------ ------ 600 ------ ------ ------ ------ ------ ------ ------ ------ ------ ------ 300 0 0 ------ ------ ------ ------ ------ ------ ------ ------ TOTAL 000000 000000 000000 000000 000006 000000 000030 000000 000000 000000 #SPE 1/1 : <-- MODEM FAX --> Speed B103 V.21 B212 V.22 V.22b V.32 V.32b V.27t V.29 V.17 14400 ------ ------ ------ ------ ------ ------ 30 ------ ------ 0 12000 ------ ------ ------ ------ ------ ------ 0 ------ ------ 0 9600 ------ ------ ------ ------ ------ 0 0 ------ 0 0 7200 ------ ------ ------ ------ ------ - 0 ------ 0 0 4800 ------ ------ ------ ------ ------ 0 0 0 0 ------ 2400 ------ ------ ------ ------ 0 ------ ------ 0 ------ ------ 1200 ------ ------ 0 0 6 ------ ------ ------ ------ ------ 600 ------ ------ ------ ------ ------ ------ ------ ------ ------ ------ 300 0 0 ------ ------ ------ ------ ------ ------ ------ ------ TOTAL 000000 000000 000000 000000 000006 000000 000030 000000 000000 000000 .
The following example shows output for the show spe modem low speed command on the Cisco AS5800 with universal port card. This example displays standard low-speed connections for SPEs in slot 8:
Router# show spe modem low speed 1/8/0 1/8/6
-- Indicates an invalid speed for a standard
#SPE 1/08/00 : <-- MODEM FAX -->
Speed B103 V.21 B212 V.22 V.22b V.23 V.32 V.32b V.27t V.29 V.17
14400 ----- ----- ----- ----- ----- ----- ----- 0 ----- ----- 0
12000 ----- ----- ----- ----- ----- ----- ----- 0 ----- ----- 0
9600 ----- ----- ----- ----- ----- ----- 0 0 ----- 0 0
7200 ----- ----- ----- ----- ----- ----- - 0 ----- 0 0
4800 ----- ----- ----- ----- ----- ----- 0 0 0 0 -----
2400 ----- ----- ----- ----- 0 ----- ----- ----- 0 ----- -----
1200 ----- ----- 0 0 0 0 ----- ----- ----- ----- -----
300 0 0 ----- ----- ----- ----- ----- ----- ----- ----- -----
TOTAL 00000 00000 00000 00000 00000 00000 00000 00000 00000 00000 00000
ÿ
Related Commands
show spe modem high speed Displays the total number of connections within each modulization or codec for a specific range of Service Processing Elements (SPEs).
Command
Description
To display the total number of connections within each low modulation or codec for the specified Service Processing Elements (SPEs), use the show spe modem low standard EXEC command.
Cisco AS5400 with NextPort DFC
show spe modem low standard {summary | slot | slot/spe}
Cisco AS5800 with universal port card
show spe modem low standard {summary | shelf/slot | shelf/slot/spe}
Syntax Description
summary Shows a brief list of all modulation connections negotiated. slot (Optional) All ports on the specified slot. For the AS5400, slot values range from 0 to 7. slot/spe (Optional) All ports on the specified slot and SPE. For the AS5400, slot values range from 0 to 7 and SPE values range from 0 to 17. shelf/slot (Optional) All ports on the specified shelf and slot. For the AS5800, shelf values range from 0 to 1 and UPC slot values range from 2 to 11. shelf/slot/spe (Optional) All ports on the specified SPE. For the AS5800, shelf values range from 0 to 1, slot values range from 2 to 11, and SPE values range from 0 to 53.
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
12.1(1)XD This command was introduced on the Cisco AS5400. 12.1(3)T This command was supported on the Cisco AS5400 and Cisco AS5800.
Release
Modification
Examples
The following example displays standard low speed connections for SPEs in slot 5 on the Cisco AS5400.
Router# show spe modem low standard 5
<-- MODEM FAX -->
SPE/Mod-> B103 V.21 B212 V.22 V.22b V.23 V.32 V.32b V.27t V.29 V.17
5/00 0 0 0 0 0 0 0 0 0 0 0
5/01 0 0 0 0 0 0 0 0 0 0 0
5/02 0 0 0 0 0 0 0 0 0 0 0
5/03 0 0 0 0 0 0 0 0 0 0 0
5/04 0 0 0 0 0 0 0 0 0 0 0
5/05 0 0 0 0 0 0 0 0 0 0 0
5/06 0 0 0 0 0 0 0 0 0 0 0
5/07 0 0 0 0 0 0 0 0 0 0 0
5/08 0 0 0 0 0 0 0 0 0 0 0
5/09 0 0 0 0 0 0 0 0 0 0 0
5/10 0 0 0 0 0 0 0 0 0 0 0
5/11 0 0 0 0 0 0 0 0 0 0 0
5/12 0 0 0 0 0 0 0 0 0 0 0
5/13 0 0 0 0 0 0 0 0 0 0 0
5/14 0 0 0 0 0 0 0 0 0 0 0
5/15 0 0 0 0 0 0 0 0 0 0 0
5/16 0 0 0 0 0 0 0 0 0 0 0
5/17 0 0 0 0 0 0 0 0 0 0 0
TOTAL 00000 00000 00000 00000 00000 00000 00000 00000 00000 00000 00000
The following example displays standard low speed connections for SPEs in slot 8 on the Cisco AS5800.
Router# show spe modem low standard 1/8
<-- MODEM FAX -->
SPE/Mod-> B103 V.21 B212 V.22 V.22b V.23 V.32 V.32b V.27t V.29 V.17
1/08/00 0 0 0 0 0 0 0 0 0 0 0
1/08/01 0 0 0 0 0 0 0 0 0 0 0
1/08/02 0 0 0 0 0 0 0 0 0 0 0
1/08/03 0 0 0 0 0 0 0 0 0 0 0
1/08/04 0 0 0 0 0 0 0 0 0 0 0
1/08/05 0 0 0 0 0 0 0 0 0 0 0
1/08/06 0 0 0 0 0 0 0 0 0 0 0
1/08/07 0 0 0 0 0 0 0 0 0 0 0
1/08/08 0 0 0 0 0 0 0 0 0 0 0
1/08/09 0 0 0 0 0 0 0 0 0 0 0
1/08/10 0 0 0 0 0 0 0 0 0 0 0
1/08/11 0 0 0 0 0 0 0 0 0 0 0
1/08/12 0 0 0 0 0 0 0 0 0 0 0
1/08/13 0 0 0 0 0 0 0 0 0 0 0
1/08/14 0 0 0 0 0 0 0 0 0 0 0
1/08/15 0 0 0 0 0 0 0 0 0 0 0
1/08/16 0 0 0 0 0 0 0 0 0 0 0
1/08/17 0 0 0 0 0 0 0 0 0 0 0
1/08/18 0 0 0 0 0 0 0 0 0 0 0
1/08/19 0 0 0 0 0 0 0 0 0 0 0
1/08/20 0 0 0 0 0 0 0 0 0 0 0
<-- MODEM FAX -->
SPE/Mod-> B103 V.21 B212 V.22 V.22b V.23 V.32 V.32b V.27t V.29 V.17
1/08/21 0 0 0 0 0 0 0 0 0 0 0
1/08/22 0 0 0 0 0 0 0 0 0 0 0
1/08/23 0 0 0 0 0 0 0 0 0 0 0
1/08/24 0 0 0 0 0 0 0 0 0 0 0
1/08/25 0 0 0 0 0 0 0 0 0 0 0
1/08/26 0 0 0 0 0 0 0 0 0 0 0
1/08/27 0 0 0 0 0 0 0 0 0 0 0
1/08/28 0 0 0 0 0 0 0 0 0 0 0
1/08/29 0 0 0 0 0 0 0 0 0 0 0
1/08/30 0 0 0 0 0 0 0 0 0 0 0
1/08/31 0 0 0 0 0 0 0 0 0 0 0
1/08/32 0 0 0 0 0 0 0 0 0 0 0
1/08/33 0 0 0 0 0 0 0 0 0 0 0
1/08/34 0 0 0 0 0 0 0 0 0 0 0
1/08/35 0 0 0 0 0 0 0 0 0 0 0
1/08/36 0 0 0 0 0 0 0 0 0 0 0
1/08/37 0 0 0 0 0 0 0 0 0 0 0
1/08/38 0 0 0 0 0 0 0 0 0 0 0
1/08/39 0 0 0 0 0 0 0 0 0 0 0
1/08/40 0 0 0 0 0 0 0 0 0 0 0
1/08/41 0 0 0 0 0 0 0 0 0 0 0
1/08/42 0 0 0 0 0 0 0 0 0 0 0
<-- MODEM FAX -->
SPE/Mod-> B103 V.21 B212 V.22 V.22b V.23 V.32 V.32b V.27t V.29 V.17
1/08/43 0 0 0 0 0 0 0 0 0 0 0
1/08/44 0 0 0 0 0 0 0 0 0 0 0
1/08/45 0 0 0 0 0 0 0 0 0 0 0
1/08/46 0 0 0 0 0 0 0 0 0 0 0
1/08/47 0 0 0 0 0 0 0 0 0 0 0
1/08/48 0 0 0 0 0 0 0 0 0 0 0
1/08/49 0 0 0 0 0 0 0 0 0 0 0
1/08/50 0 0 0 0 0 0 0 0 0 0 0
1/08/51 0 0 0 0 0 0 0 0 0 0 0
1/08/52 0 0 0 0 0 0 0 0 0 0 0
1/08/53 0 0 0 0 0 0 0 0 0 0 0
TOTAL 00000 00000 00000 00000 00000 00000 00000 00000 00000 00000 00000
Related Commands
show spe modem high standard Displays the total number of connections within each high modulation or codec for a specific range of SPE.
Command
Description
To display summary of modem statistics for the specified Service Processing Element (SPE) or range of SPEs, use the show spe modem summary EXEC command.
Cisco AS5400 with NextPort DFC
show spe modem summary [slot | slot/spe]
Cisco AS5800 with universal port card
show spe modem summary [shelf/slot | shelf/slot/spe]
Syntax Description
slot (Optional) All ports on the specified slot. For the AS5400, slot values range from 0 to 7. slot/spe (Optional) All ports on the specified slot and SPE. For the AS5400, slot values range from 0 to 7 and SPE values range from 0 to 17. shelf/slot (Optional) All ports on the specified shelf and slot. For the AS5800, shelf values range from 0 to 1 and UPC slot values range from 2 to 11. shelf/slot/spe (Optional) All ports on the specified SPE. For the AS5800, shelf values range from 0 to 1, slot values range from 2 to 11, and SPE values range from 0 to 53.
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
12.1(1)XD This command was introduced on the Cisco AS5400. 12.1(3)T This command was supported on the Cisco AS5400 and Cisco AS5800.
Release
Modification
Examples
The following example displays the show spe modem summary command on the Cisco AS5400.
Router# show spe modem summary
Async1/00 - 5/107, TTY216 - 755
786 incoming completes 4 incoming failures
0 outgoing completes 0 outgoing failures
0 failed dial attempts 0 ring no answers 0 autotests
0 no carriers 0 dial timeouts 0 autotest fails
0 no dial tones 0 link failures 0 fail count
0 watchdog timeouts 0 protocol errors 0 recovers
Transmit Speed Counters :
Speed Calls Speed Calls Speed Calls Speed Calls Speed Calls
60000 0 48000 0 38400 0 30666 0 12000 0
58000 0 46666 0 38000 0 29333 0 9600 0
56000 0 46000 0 37333 0 28800 10 7200 0
54666 0 45333 0 36000 0 28000 0 4800 0
54000 0 44000 0 34666 0 26400 0 2400 0
53333 0 42666 0 34000 0 24000 0 1200 0
52000 0 42000 0 33600 631 21600 0 300 0
50666 0 41333 0 33333 0 19200 0
50000 0 40000 0 32000 0 16800 0
49333 0 38666 0 31200 145 14400 0
Receive Speed Counters :
Speed Calls Speed Calls Speed Calls Speed Calls Speed Calls
38400 0 26400 0 16800 0 7200 0 300 0
33600 786 24000 0 14400 0 4800 0
31200 0 21600 0 12000 0 2400 0
28800 0 19200 0 9600 0 1200 0
The following example displays the show spe modem summary command on the Cisco AS5800.
Router# show spe modem summary
Async1/2/00 - 1/3/323, TTY972 - 1619
4827 incoming completes 284 incoming failures
0 outgoing completes 0 outgoing failures
0 failed dial attempts 0 ring no answers 0 autotests
0 no carriers 11 dial timeouts 0 autotest fails
0 no dial tones 0 link failures 0 fail count
0 watchdog timeouts 2787 protocol errors 0 recovers
Transmit Speed Counters
Speed Calls Speed Calls Speed Calls Speed Calls Speed Calls
60000 0 48000 432 38400 0 30666 0 12000 143
58000 0 46666 0 38000 4 29333 0 9600 5
56000 15 46000 56 37333 111 28800 700 7200 11
54666 0 45333 299 36000 84 28000 5 4800 2
54000 0 44000 227 34666 0 26400 267 2400 0
53333 123 42666 0 34000 39 24000 46 1200 3
52000 563 42000 68 33600 323 21600 27 300 0
50666 0 41333 38 33333 9 19200 38
50000 59 40000 65 32000 20 16800 12
49333 371 38666 0 31200 654 14400 5
Receive Speed Counters
Speed Calls Speed Calls Speed Calls Speed Calls Speed Calls
38400 0 26400 2286 16800 11 7200 1 300 2
33600 113 24000 267 14400 139 4800 1
31200 216 21600 56 12000 4 2400 3
28800 1665 19200 47 9600 16 1200 0
Related Commands
show spe Displays history statistics of all SPEs, a specified SPE, or the specified range of SPEs. show spe digital Displays history statistics of all digital SPEs, in summary form or for SPEs starting with a specified slot or a specified shelf/slot/range of SPEs show spe modem disconnect-reason Displays all modem disconnect reasons for the specified SPE or range of SPEs. show spe modem summary Displays summary of modem statistics for the specified SPE or range of SPEs.
Command
Description
To display SPE recovery statistics, use the show spe recovery EXEC command.
Cisco AS5400 with NextPort DFC
show spe recovery [slot | slot/spe]
Cisco AS5800 with universal port card
show spe recovery [shelf/slot | shelf/slot/spe]
Syntax Description
slot (Optional) All ports on the specified slot. For the AS5400, slot values range from 0 to 7. slot/spe (Optional) All ports on the specified slot and SPE. For the AS5400, slot values range from 0 to 7 and SPE values range from 0 to 17. shelf/slot (Optional) All ports on the specified shelf and slot. For the AS5800, shelf values range from 0 to 1 and UPC slot values range from 2 to 11. shelf/slot/spe (Optional) All ports on the specified SPE. For the AS5800, shelf values range from 0 to 1, slot values range from 2 to 11, and SPE values range from 0 to 53.
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
12.1(1)XD This command was introduced on the Cisco AS5400. 12.1(3)T This command was supported on the Cisco AS5400 and Cisco AS5800.
Release
Modification
Usage Guidelines
Use this command to see a list of recovered SPEs.
Examples
The following example displays the show spe recovery command on the Cisco AS5400.
Router# show spe recovery SPE# Session Abort Session NAK Call Failure 1/00 0 0 0 1/01 0 0 0 1/02 0 0 0 1/03 0 0 0 1/04 0 0 0 1/05 0 0 0 1/06 0 0 0 1/07 0 0 0 1/08 0 0 0 1/09 0 0 0 1/10 0 0 0 1/11 0 0 0 1/12 0 0 0 1/13 0 0 0 1/14 0 0 0 1/15 0 0 0 1/16 0 0 0 1/17 0 0 0
The following example displays the show spe recovery command on the Cisco AS5800.
Router# show spe recovery 1/8 SPE# Session Abort Session NAK Call Failure 1/08/00 0 0 0 1/08/01 0 0 0 1/08/02 0 0 0 1/08/03 0 0 0 1/08/04 0 0 0 1/08/05 0 0 0 1/08/06 0 0 0 1/08/07 0 0 0 1/08/08 0 0 0 1/08/09 0 0 0 1/08/10 0 0 0 1/08/11 0 0 0 1/08/12 0 0 0 1/08/13 0 0 0 1/08/14 0 0 0 1/08/15 0 0 0 1/08/16 0 0 0 1/08/17 0 0 0 1/08/18 0 0 0 1/08/19 0 0 0 1/08/20 0 0 0 1/08/21 0 0 0 1/08/22 0 0 0 1/08/23 0 0 0 1/08/24 0 0 0 1/08/25 0 0 0 1/08/26 0 0 0 1/08/27 0 0 0 1/08/28 0 0 0 1/08/29 0 0 0 1/08/30 0 0 0 1/08/31 0 0 0 1/08/32 0 0 0 1/08/33 0 0 0 1/08/34 0 0 0 1/08/35 0 0 0 1/08/36 0 0 0 1/08/37 0 0 0 1/08/38 0 0 0 1/08/39 0 0 0 1/08/40 0 0 0 1/08/41 0 0 0 1/08/42 0 0 0 1/08/43 0 0 0 1/08/44 0 0 0 1/08/45 0 0 0 1/08/46 0 0 0 1/08/47 0 0 0 1/08/48 0 0 0 1/08/49 0 0 0 1/08/50 0 0 0 1/08/51 0 0 0 1/08/52 0 0 0 1/08/53 0 0 0
Related Commands
show spe Displays SPE status.
Command
Description
To display the firmware version on a Service Processing Element (SPE), use the show spe version EXEC command. Also, this command displays the version to firmware file mappings.
Cisco AS5400 with NextPort DFC
show spe version [slot | slot/spe]
Cisco AS5800 with universal port card
show spe version [shelf/slot | shelf/slot/spe]
Syntax Description
slot (Optional) All ports on the specified slot. For the AS5400, slot values range from 0 to 7. slot/spe (Optional) All ports on the specified slot and SPE. For the AS5400, slot values range from 0 to 7 and SPE values range from 0 to 17. shelf/slot (Optional) All ports on the specified shelf and slot. For the AS5800, shelf values range from 0 to 1 and UPC slot values range from 2 to 11. shelf/slot/spe (Optional) All ports on the specified SPE. For the AS5800, shelf values range from 0 to 1, slot values range from 2 to 11, and SPE values range from 0 to 53.
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
12.0(7)T This command was introduced. 12.1(1)XD This command was modified for the Cisco AS5400. 12.1(3)T This command was supported on the Cisco AS5400 and Cisco AS5800.
Release
Modification
Usage Guidelines
Use the show spe version command to display the firmware version running on a specific SPE. If shelf/slot/spe is specified, the firmware version for the identified SPE or range of SPEs is displayed. If slot is specified, the firmware version for the identified SPEs in this slot or range of slots is displayed. If no argument is specified, all SPE versions are displayed.
|
Note The show spe version command is similar to the show modem mapping MICA modem commnd. |
Examples
The following example displays the output of show spe version on a Cisco AS5400:
Router# show spe version
IOS-Bundled Default Firmware-Filename Version Firmware-Type
===================================== ======= =============
system:/ucode/np_spe_firmware1 0.6.5.5 SPE firmware
0.0.0.0 Portware
On-Flash Firmware-Filename Version Firmware-Type
========================== ======= =============
flash:np.spe 0.6.4.5 SPE firmware
SPE-# SPE-Type SPE-Port-Range Version UPG Firmware-Filename
4/00 CSMV6 0000-0005 0.6.5.5 N/A np.spe
4/01 CSMV6 0006-0011 0.6.5.5 N/A ios-bundled default
4/02 CSMV6 0012-0017 0.6.5.5 N/A ios-bundled default
4/03 CSMV6 0018-0023 0.6.5.5 N/A ios-bundled default
4/04 CSMV6 0024-0029 0.6.5.5 N/A ios-bundled default
4/05 CSMV6 0030-0035 0.6.5.5 N/A ios-bundled default
4/06 CSMV6 0036-0041 0.6.5.5 N/A ios-bundled default
4/07 CSMV6 0042-0047 0.6.5.5 N/A ios-bundled default
4/08 CSMV6 0048-0053 0.6.5.5 N/A ios-bundled default
4/09 CSMV6 0054-0059 0.6.5.5 N/A ios-bundled default
4/10 CSMV6 0060-0065 0.6.5.5 N/A ios-bundled default
4/11 CSMV6 0066-0071 0.6.5.5 N/A ios-bundled default
4/12 CSMV6 0072-0077 0.6.5.5 N/A ios-bundled default
4/13 CSMV6 0078-0083 0.6.5.5 N/A ios-bundled default
4/14 CSMV6 0084-0089 0.6.5.5 N/A ios-bundled default
4/15 CSMV6 0090-0095 0.6.5.5 N/A ios-bundled default
4/16 CSMV6 0096-0101 0.6.5.5 N/A ios-bundled default
4/17 CSMV6 0102-0107 0.6.5.5 N/A ios-bundled default
The following example displays the output of show spe version on a Cisco AS5800:
Router# show spe version 1/8 IOS-Bundled Default Firmware-Filename Version Firmware-Type ===================================== ======= ============= system:/ucode/np_spe_firmware1 0.0.6.81 SPE firmware system:/ucode/mica_board_firmware 2.7.2.0 Mica Portware On-Flash Firmware-Filename Version Firmware-Type ========================== ======= ============= slot0:np_6_81.spe 0.0.6.81 SPE firmware slot0:np_6_80.spe 0.0.6.80 SPE firmware slot0:mica-modem-pw.2.7.1.1.bin 2.7.1.0 Mica Portware slot0:mica-modem-pw.2.7.2.0.bin 2.7.2.0 Mica Portware SPE-# SPE-Type SPE-Port-Range Version UPG Firmware-Filename 1/08/00 CSMV6 0000-0005 0.0.6.81 N/A ios-bundled default 1/08/01 CSMV6 0006-0011 0.0.6.81 N/A ios-bundled default 1/08/02 CSMV6 0012-0017 0.0.6.81 N/A ios-bundled default 1/08/03 CSMV6 0018-0023 0.0.6.81 N/A ios-bundled default 1/08/04 CSMV6 0024-0029 0.0.6.81 N/A ios-bundled default 1/08/05 CSMV6 0030-0035 0.0.6.81 N/A ios-bundled default 1/08/06 CSMV6 0036-0041 0.0.6.81 N/A ios-bundled default 1/08/07 CSMV6 0042-0047 0.0.6.81 N/A ios-bundled default 1/08/08 CSMV6 0048-0053 0.0.6.81 N/A ios-bundled default 1/08/09 CSMV6 0054-0059 0.0.6.81 N/A ios-bundled default 1/08/10 CSMV6 0060-0065 0.0.6.81 N/A ios-bundled default 1/08/11 CSMV6 0066-0071 0.0.6.81 N/A ios-bundled default 1/08/12 CSMV6 0072-0077 0.0.6.81 N/A ios-bundled default 1/08/13 CSMV6 0078-0083 0.0.6.81 N/A ios-bundled default 1/08/14 CSMV6 0084-0089 0.0.6.81 N/A ios-bundled default 1/08/15 CSMV6 0090-0095 0.0.6.81 N/A ios-bundled default 1/08/16 CSMV6 0096-0101 0.0.6.81 N/A ios-bundled default 1/08/17 CSMV6 0102-0107 0.0.6.81 N/A ios-bundled default 1/08/18 CSMV6 0108-0113 0.0.6.81 N/A ios-bundled default 1/08/19 CSMV6 0114-0119 0.0.6.81 N/A ios-bundled default 1/08/20 CSMV6 0120-0125 0.0.6.81 N/A ios-bundled default 1/08/21 CSMV6 0126-0131 0.0.6.81 N/A ios-bundled default 1/08/22 CSMV6 0132-0137 0.0.6.81 N/A ios-bundled default 1/08/23 CSMV6 0138-0143 0.0.6.81 N/A ios-bundled default 1/08/24 CSMV6 0144-0149 0.0.6.81 N/A ios-bundled default 1/08/25 CSMV6 0150-0155 0.0.6.81 N/A ios-bundled default 1/08/26 CSMV6 0156-0161 0.0.6.81 N/A ios-bundled default 1/08/27 CSMV6 0162-0167 0.0.6.81 N/A ios-bundled default 1/08/28 CSMV6 0168-0173 0.0.6.81 N/A ios-bundled default 1/08/29 CSMV6 0174-0179 0.0.6.81 N/A ios-bundled default 1/08/30 CSMV6 0180-0185 0.0.6.81 N/A ios-bundled default 1/08/31 CSMV6 0186-0191 0.0.6.81 N/A ios-bundled default 1/08/32 CSMV6 0192-0197 0.0.6.81 N/A ios-bundled default 1/08/33 CSMV6 0198-0203 0.0.6.81 N/A ios-bundled default 1/08/34 CSMV6 0204-0209 0.0.6.81 N/A ios-bundled default 1/08/35 CSMV6 0210-0215 0.0.6.81 N/A ios-bundled default 1/08/36 CSMV6 0216-0221 0.0.6.81 N/A ios-bundled default 1/08/37 CSMV6 0222-0227 0.0.6.81 N/A ios-bundled default 1/08/38 CSMV6 0228-0233 0.0.6.81 N/A ios-bundled default 1/08/39 CSMV6 0234-0239 0.0.6.81 N/A ios-bundled default 1/08/40 CSMV6 0240-0245 0.0.6.81 N/A ios-bundled default 1/08/41 CSMV6 0246-0251 0.0.6.81 N/A ios-bundled default 1/08/42 CSMV6 0252-0257 0.0.6.81 N/A ios-bundled default 1/08/43 CSMV6 0258-0263 0.0.6.81 N/A ios-bundled default 1/08/44 CSMV6 0264-0269 0.0.6.81 N/A ios-bundled default 1/08/45 CSMV6 0270-0275 0.0.6.81 N/A ios-bundled default 1/08/46 CSMV6 0276-0281 0.0.6.81 N/A ios-bundled default 1/08/47 CSMV6 0282-0287 0.0.6.81 N/A ios-bundled default 1/08/48 CSMV6 0288-0293 0.0.6.81 N/A ios-bundled default 1/08/49 CSMV6 0294-0299 0.0.6.81 N/A ios-bundled default 1/08/50 CSMV6 0300-0305 0.0.6.81 N/A ios-bundled default 1/08/51 CSMV6 0306-0311 0.0.6.81 N/A ios-bundled default 1/08/52 CSMV6 0312-0317 0.0.6.81 N/A ios-bundled default 1/08/53 CSMV6 0318-0323 0.0.6.81 N/A ios-bundled default
Related Commands
firmware location Upgrades SPE firmware after the new SPE firmware image is retrieved from CCO or elsewhere. show spe Displays history statistics of all SPEs, a specified SPE, or the specified range of SPEs.
Command
Description
To disable a port, use the shutdown port configuration command. Use the no form of this command to change the administrative state of a port from out-of-service to in service.
shutdownSyntax Description
This command has no arguments or keywords.
Defaults
Port is enabled.
Command Modes
Port configuration
Command History
12.1(1)XD This command was introduced on the Cisco AS5400. 12.1(3)T This command was supported on the Cisco AS5400 and Cisco AS5800.
Release
Modification
Usage Guidelines
The shutdown command disables a port.
|
Note The shutdown command is similar to the modem shutdown MICA modem command. |
Examples
The following example first resets and un-resets port 1 to 18 before executingthe shutdown command:
Router(config)# port Router(config-port)# shutdown Router(config-port)# no shutdown Router(config-port)# exit
Related Commands
busyout Gracefully disables a port by waiting for the active services on the specified port to end. clear port Resets the port and clears any active calls to the port. clear spe Reboots SPEs that are in any state. show spe Displays history statistics of all SPEs, a specified SPE, or the specified range of SPEs.
Command
Description
To take a Service Processing Element (SPE) out of service, use the shutdown SPE configuration command. Use the no form of this command to change the administrative state of this SPE from down to up.
shutdownSyntax Description
This command has no arguments or keywords.
Defaults
SPE is enabled.
Command Modes
SPE configuration
Command History
12.1(1)XD This command was introduced on the Cisco AS5400. 12.1(3)T This command was supported on the Cisco AS5400 and Cisco AS5800.
Release
Modification
Usage Guidelines
The shutdown SPE configuration command takes a Service Processing Element (SPE) out of service. The no form of this command changes the administrative state of this SPE from down to up.
Examples
The following example first resets SPE 1 to 18:
Router(config)# spe 1/1 1/18 Router(config-spe)# shutdown Router(config-spe)# no shutdown Router(config-spe)#
Related Commands
busyout Gracefully disables an SPE by waiting for all the active services on the specified SPE to end. clear spe Reboots SPEs that are in any state. show spe Displays history statistics of all SPEs, a specified SPE, or the specified range of SPEs.
Command
Description
To access the Service Processing Element (SPE) configuration mode and set the range of SPEs, use the spe global configuration command.
Cisco AS5400 with NextPort DFC
spe {slot | slot/spe}
Cisco AS5800 with universal port card
spe {shelf/slot | shelf/slot/spe}
Syntax Description
slot All ports on the specified slot. For the AS5400, slot values range from 0 to 7. slot/spe All ports on the specified slot and SPE. For the AS5400, slot values range from 0 to 7 and SPE values range from 0 to 17. shelf/slot All ports on the specified shelf and slot. For the AS5800, shelf values range from 0 to 1 and UPC slot values range from 2 to 11. shelf/slot/spe All ports on the specified SPE. For the AS5800, shelf values range from 0 to 1, slot values range from 2 to 11, and SPE values range from 0 to 53.
Defaults
No default behavior or values.
Command Modes
Global Configuration
Command History
12.0(4)XI1 This command was introduced. 12.0(5)T This document changed to reflect new information on the command. 12.1(1)XD This command was introduced on the Cisco AS5400. 12.1(3)T This command was supported on the Cisco AS5400 and Cisco AS5800.
Release
Modification
Usage Guidelines
The spe global configuration command enables the SPE configuration mode. Configure your SPE by specifying a slot and an SPE associated with the slot; or, you can configure a range of SPEs by specifying the first and last SPE in the range.
When the access server is booted, the spe global configuration command specifies the location from which the firmware image is downloaded to the SPE. If the spe configuration command is used to download the firmware from Flash memory and subsequently the no version of the exact command is entered, then the spe command downloads the embedded firmware.
|
Note Use this command when traffic is low because the spe download does not begin until the modems have no active calls. |
|
Caution The spe command is a configuration command. Save it using the write memory command; otherwise, the configuration is not saved. If the configuration is not saved, the downloading of the specified firmware does not occur after the next reboot. |
Examples
The following example shows the spe command being used from global configuration mode to access the SPE configuration mode for the range of SPEs from 1/2 to 1/4 on the Cisco AS5400:
Router(config)# spe 1/2 1/4
The following example specifies the range for use of the shutdown command:
Router(config)# spe 1/1 1/18 Router(config-spe)# shutdown Router(config-spe)# no shutdown Router(config-spe)#
Related Commands
show spe Display history statistics of all SPEs, a specified SPE, or the specified range of SPEs.
Command
Description
To generate a modem call-record at the end of each call, use the spe call-record global configuration command. Use the no form of the command to cancel the request to generate the reports.
spe call-record modem {max-userid number | quiet}
Syntax Description
max-userid number Maximum length of User ID for the modem call record report in number of bytes. The range is 0 to 100. quiet Disables logging to console and terminal, but not to syslog.
Defaults
SPE call-record enabled
Command Modes
Global configuration
Command History
12.1(1)XD This command was introduced on the Cisco AS5400. 12.1(3)T This command was supported on the Cisco AS5400 and Cisco AS5800.
Release
Modification
Usage Guidelines
The spe modem-call-record command generates a modem call-record at the end of each call.
|
Note The spe modem-call-record command is similar to the modem call-record command. |
Examples
The following example displays SPE call-record:
Router# config t Router(config)# spe call-record modem max-userid 50 Router(config)# end Router# 00:18:30: %SYS-5-CONFIG_I: Configured from console by console Router# write Building configuration... [OK]
The following is an example of traces generated when a call terminates. The logs from the show port modem log command do not change as a result of using the spe call-record command.
... %LINK-3-UPDOWN: Interface Async5/105, changed state to down %MODEMCALLRECORD-6-PM_TERSE_CALL_RECORD: DS0 slot/contr/chan=4/2/15, shelf/slot/port=5/37, call_id=EE, userid=touraco-e1-4, ip=79.188.24.1, calling=(n/a), called=35160, std=V.34+, prot=LAP-M, comp=V.42bis, init-rx/tx b-rate=33600/33600, finl-rx/tx b-rate=33600/33600, rbs=0, d-pad=None, retr=1, sq=5, snr=10495, rx/tx chars=286/266, bad=0, rx/tx ec=16/6, bad=0, time=96, finl-state=Steady Retrain, disc(radius)=(n/a)/(n/a), disc(modem)=1F00 <unknown>/Requested by host/non-specific host disconnect %MODEMCALLRECORD-6-PM_TERSE_CALL_RECORD: DS0 slot/contr/chan=4/1/24, shelf/slot/port=5/38, call_id=FD, userid=touraco-e1-4, ip=79.205.24.1, calling=(n/a), called=35170, std=V.34+, prot=LAP-M, comp=V.42bis, init-rx/tx b-rate=33600/33600, finl-rx/tx b-rate=33600/33600, rbs=0, d-pad=None, retr=1, sq=5, snr=10495, rx/tx chars=289/267, bad=0, rx/tx ec=17/7, bad=0, time=93, finl-state=Steady Retrain, disc(radius)=(n/a)/(n/a), disc(modem)=1F00 <unknown>/Requested by host/non-specific host disconnect %MODEMCALLRECORD-6-PM_TERSE_CALL_RECORD: DS0 slot/contr/chan=4/3/15, shelf/slot/port=5/2, call_id=FF, userid=touraco-e1-4, ip=79.200.24.1, calling=(n/a), called=35170, std=V.34+, prot=LAP-M, comp=V.42bis, init-rx/tx b-rate=33600/33600, finl-rx/tx b-rate=33600/33600, rbs=0, d-pad=None, retr=1, sq=5, snr=10495, rx/tx chars=287/270, bad=0, rx/tx ec=17/7, bad=0, time=92, finl-state=Steady Retrain, disc(radius)=(n/a)/(n/a), disc(modem)=1F00 <unknown>/Requested by host/non-specific host disconnect %MODEMCALLRECORD-6-PM_TERSE_CALL_RECORD: DS0 slot/contr/chan=4/3/10, shelf/slot/port=5 ...
Related Commands
There are no related commands.
To specify the country while setting the Universal Port DFC parameters (including country code and encoding), use the spe country global configuration command. Use the no form of this command to set the country code to the default value.
spe country country_name
Syntax Description
country_name Name of the country.
Defaults
Disabled
Command Modes
Global configuration
Command History
12.1(1)XD This command was introduced on the Cisco AS5400. 12.1(3)T This command was supported on the Cisco AS5400 and Cisco AS5800.
Release
Modification
Usage Guidelines
On the Cisco access server, DS0 companding law selection is configured for the entire system rather than on individual voice ports. Set spe country to the appropriate country.
If T1s are configured, the default is t1-default; if E1s are configured, the default is e1-default.
The Cisco access server must be in an Idle state (no calls are active) to execute the spe country command. All sessions on all modules in all slots must be Idle.
|
Note The spe country command is similar to the modem country command. |
A list of all supported countries is displayed in Table 2.
| Keyword | Country | Companding Law |
|---|---|---|
australia | Australia | a-law |
austria | Austria | a-law |
belgium | Belgium | a-law |
china | China | a-law |
cyprus | Cyprus | a-law |
czech-republic | Czech/Slovak Republic | a-law |
denamrk | Denmark | a-law |
e1-default | Default for E-1 | a-law |
finland | Finland | a-law |
france | France | a-law |
germany | Germany | a-law |
hong-kong | Hong Kong | u-law |
india | India | a-law |
ireland | Ireland | a-law |
israel | Israel | a-law |
italy | Italy | a-law |
japan | Japan | u-law |
malaysia | Malaysia | a-law |
netherlands | Netherlands | a-law |
new-zealand | New Zealand | a-law |
norway | Norway | a-law |
poland | Poland | a-law |
portugal | Portugal | a-law |
russia | Russia | a-law |
singapore | Singapore | a-law |
south-africa | South Africa | a-law |
spain | Spain | a-law |
sweden | Sweden | a-law |
switzerland | Switzerland | a-law |
t1-default | Default for T1 | u-law |
taiwan | Taiwan | u-law |
thailand | Thailand | a-law |
turkey | Turkey | a-law |
united-kingdom | United Kingdom | a-law |
usa | United States of America | u-law |
Examples
The following example configures the setting of the country code to E1 default:
Router(config)# spe country e1-default
The following example configures the setting of the country code to D1 default:
Router(config)# spe country d1-default
Related Commands
show spe Displays history statistics of all SPEs, a specified SPE, or the specified range of SPEs.
Command
Reference
To perform download maintenance on Service Processing Elements (SPEs) that are marked for recovery, use the spe download global configuration command.
spe download maintenance {time hh:mm | stop-time hh:mm | max-spes num-of-spes| window time-period | expired-window {disable | drop-call | reschedule}}
Syntax Description
time hh:mm Time of the day to start the download maintenance activity. Enter the value in the format of the variable as shown. Default is 03:00 a.m.. stop-time hh:mm Time of the day to stop the download maintenance activity. Enter the value in the format of the variable as shown. max-spes number Maximum number of SPEs that can simultaneously be in maintenance. The value is between 1-10000. Default is equal to 20 percent of the maximum number of SPEs in each NextPort DFC. window time-period Time window to perform the maintenance activity. The value is between 0-360 minutes. Default is 60 minutes. expired-window Action to take if SPE maintenance is not completed within window. Default is reschedule. drop-call Force download by dropping active calls. reschedule Defer recovery to the next maintenance time.
Defaults
Enabled
Command Modes
Global configuration
Command History
12.1(1)XD This command was introduced for the Cisco AS5400. 12.1(3)T This command was supported on the Cisco AS5400 and Cisco AS5800.
Release
Modification
Usage Guidelines
The SPE download maintenance activity takes place when SPEs are marked for recovery. The settings are enabled by default. When you want to change the default settings to a desired setting, use the spe download maintenance command parameters to perform SPE download maintenance activity with the specific changes.
Enter the time hh:mm keyword to set a time to start the SPE download maintenance activity. Then enter the stop-time hh:mm keyword to set a time to stop the download maintenance. Next enter the max-spes number keyword to set the number of SPEs for the download maintenance. Then enter the window time-period keyword to set a time period to perform the download maintenance. Finally, enter the expired-window keyword to set actions in the event the SPE download maintenance is not completed in the set window time-period.
The download maintenance activity starts at the set start time and steps through all the SPEs that need recovery and the SPEs that need a firmware upgrade and starts maintenance on the maximum number of set SPEs for maintenance. The system waits for the window delay time for all the ports on the SPE to become inactive before moving the SPE to the Idle state. Immediately after the SPE moves to Idle state, the system starts to download firmware. If the ports are still in use by the end of window delay time, depending upon the expired-window setting, connections on the SPE ports are shutdown and the firmware is downloaded by choosing the drop-call option, or the firmware download is rescheduled to the next download maintenance time by choosing the reschedule option. This process continues until the number of SPEs under maintenance is below max-spes, or until stop-time (if set), or until all SPEs marked for recovery or upgrade have had their firmware reloaded.
Examples
The following example displays the spe download maintenance with the different keyword parameters:
Router(config)# spe download maintenance time 03:00 Router(config)# spe download maintenance stop-time 04:00 Router(config)# spe download maintenance max-spes 50 Router(config)# spe download maintenance window 30 Router(config)# spe download maintenance expired-window reschedule
Related Commands
firmware location Downloads firmware from Flash memory into the modems from this file location. firmware upgrade Specifies the method in which the SPE will be downloaded. show spe version Displays the firmware version on an SPE. spe recovery Sets an SPE port for recovery.
Command
Description
To set the maximum size of the history event queu for log entries for each port, use the spe log-event-size global configuration command.
spe log-event-size number
Syntax Description
number Defines the number of recorded events. The range number is 0 to 100.
Defaults
50
Command Modes
Global configuration
Command History
12.1(1)XD This command was introduced on the Cisco AS5400. 12.1(3)T This command was supported on the Cisco AS5400 and Cisco AS5800.
Release
Modification
Usage Guidelines
The spe log-event-size command sets the buffer size for the log.
Examples
The following example sets the buffer size for the event log at 40:
Router(config)# spe log-event-size 40 Router(config)#
Related Commands
show port digital log Displays the digital data event log with oldest event first. show port modem log Displays the modem port history event log or modem test log.
Command
Description
To set a Service Processing Element (SPE) port for recovery, use the spe recovery global configuration command.
spe recovery {port-action {disable | recover} | {port-threshold num-failures}
Syntax Description
port-action Action to apply to the port for recovery. Default is none. disable Sets the port in a Bad state. recover Sets the port for recovery. port-threshold num-failures The number of consecutive failed attempts made on the port before applying port-action. Enter an integer value. The range is from 1 to 1000. Default is 30 consecutive call failures.
Defaults
There are no defaults.
Command Modes
Global configuration
Command History
12.1(1)XD This command was introduced on the Cisco AS5400. 12.1(3)T This command was supported on the Cisco AS5400 and Cisco AS5800.
Release
Modification
Usage Guidelines
When a SPE port fails to connect after repeated tries, this is an indication that a problem exists in SPE/firmware. An SPE port in this state is recovered by downloading firmware.
This command moves an SPE port that fails to connect consecutively num-failures (port-threshold) to a state based on (port-action). The port is disabled (disable), and then marked for recovery (recover). Any SPE that has a port marked for recovery is downloaded when the SPE is in Idle state.
Examples
The following example displays the help entries, which describe the command parameters:
Router(config)# spe recovery Router(config)# spe recovery port-action recover Router(config)# spe recovery port-threshold 45
Related Commands <1-10000> Number of consecutive failed call-attempts to start recovery
clear port Resets the port and clears any active calls to the port. clear spe Reboots SPEs that are in any state. firmware upgrade Specifies an SPE firmware upgrade method. show spe Displays history statistics of all SPEs, a specified SPE, or the specified range of SPEs. show spe version Displays the firmware version on an SPE and displays the version to firmware file mappings. spe download maintenance Performs download maintenance on SPEs that are marked for recovery.
Command
Description
To test two specified ports back-to-back and transfer a specified amount of data between the ports, use the test port modem back-to-back EXEC command.
Cisco AS5400 with NextPort DFC
test port modem back-to-back {slot/port}
Cisco AS5800 with universal port card
test port modem back-to-back {shelf/slot/port}
Syntax Description
slot/port (Optional) All ports on the specified slot and SPE. For the AS5400, slot values range from 0 to 7 and port values range from 0 to 107. shelf/slot/port (Optional) All ports on the specified SPE. For the AS5800, shelf values range from 0 to 1, slot values range from 2 to 11, and port values range from 0 to 323.
Defaults
None
Command Modes
EXEC
Command History
11.3 The test modem back-to-back form of this command was introduced. 12.1(1)XD This command was supported on the Cisco AS5400. 12.1(3)T This command was supported on the Cisco AS5400 and Cisco AS5800.
Release
Modification
Usage Guidelines
The test port modem back-to-back command should be performed on different combinations to determine a good port.
|
Note The test port modem back-to-back command is similar to the test modem back-to-back MICA modem command. |
Examples
The following example displays a back-to-back test:
Router# test port modem back-to-back 1/1/1 Repetitions (of 10-byte packets) [1]: *Mar 02 12:13:51.743:%PM_MODEM_MAINT-5-B2BCONNECT:Modems (2/10) and (3/20) connected in back-to-back test:CONNECT33600/V34/LAP *Mar 02 12:13:52.783:%PM_MODEM_MAINT-5-B2BMODEMS:Modems (3/20) and (2/10) completed back-to-back test:success/packets = 2/2
Related Commands
port modem autotest Automatically and periodically performs a modem diagnostics test for modems inside the access server or router. port modem startup test Performs diagnostic testing for all modems. show port modem test Displays the modem port history event log or modem test log.
Command
Description
bps—Bits-per-second.
byte—Bits of information.
call or port—A name used to represent the binding of a TDM channel, service, and data queue to support a bidirectional service on the NextPort module.
Control Processor (CP)—A processor on the module that supports the NextPort messaging interface.
DFC—dial feature card, the NextPort modem carrier card (AS54-DFC-108NP) that occupies a slot in the Cisco AS5400.
EST Queue—An Error / Status / Trace message queue used to communicate out-of-band information between the host and the module.
host—A physical card that the NextPort module connects to. This can be either the platform, backplane, or a carrier card.
Mb—Megabit. 1,048,576 million bits.
MB—Megabyte. 1,048,576 million bytes.
MIB—Management Information Base.
NextPort module—A hardware card that supports the NextPort hardware and software interfaces.
Port Management Database—A database that consists of Service Processing Element and port level management information for all services.
port, timeslot, or DS0—The atomic element of a TDM stream. It provides a bandwidth of 64,000 bps.
Receive or Rx—Indicates the direction from the TDM stream to the module to the host.
Service—The algorithm executing on the NextPort module that implements a particular protocol. Two typical examples of services are a data modem and Voice over IP.
Service Processing Unit (SPU)—The processor on the module that executes protocols to process in-band data.
shared memory interface—A communication mechanism where a block of memory can be accessed by multiple processors and is used to exchange information.
SPE—Service Processing Element. A component of a NextPort module to which sessions are assigned. An SPE is a logical entity that groups six modems.
TDM—Time division multiplexing. The process whereby a high-bandwidth channel is subdivided into multiple lower-bandwidth channels.
TDM channel—One or more time slots of the HMVIP stream that constitute a single data stream. The TDM channel bandwidth is determined by 64,000 multipled by the number of time slots in the channel.
TDM stream—An HMVIP serial data stream operating at 8.192 MHz and capable of supporting 8.192MB throughput.
Transmit or Tx—Indicates the direction from the host to the module to the TDM stream.
universal service—A port on a NextPort module that can be switched freely between two or more services without changing the TDM channel.
Posted: Wed Sep 20 11:24:54 PDT 2000
Copyright 1989-2000©Cisco Systems Inc.