|
|
Use the information in this chapter to understand and configure the types of logical, or virtual, interfaces supported on Cisco routers and access servers. This chapter includes the following configuration instructions and examples:
For examples of configuration tasks, see the "Logical Interface Configuration Examples" section.
For hardware technical descriptions and information about installing interfaces, refer to the hardware installation and configuration publication for your product. For complete descriptions of the logical interface commands, refer to the "Interface Commands" chapter of the Cisco IOS Interface Command Reference. To locate documentation of other commands that appear in this chapter, use the command reference master index or search online.
You can specify a software-only interface called a loopback interface to emulate an interface. It is supported on all platforms. A loopback interface is a virtual interface that is always up and allows Border Gateway Protocol (BGP) and remote source-route bridging (RSRB) sessions to stay up even if the outbound interface is down.
You can use the loopback interface as the termination address for BGP sessions, for RSRB connections, or to establish a Telnet session from the device's console to its auxiliary port when all other interfaces are down. You can also use a loopback interface to configure IPX-PPP on asynchronous interfaces. To do so, you must associate an asynchronous interface with a loopback interface configured to run IPX. In applications where other routers or access servers attempt to reach this loopback interface, you should configure a routing protocol to distribute the subnet assigned to the loopback address.
Packets routed to the loopback interface are rerouted back to the router or access server and processed locally. IP packets routed out the loopback interface but not destined to the loopback interface are dropped. This means that the loopback interface serves as the Null 0 interface also.
 |
Note Loopback does not work on an X.21 DTE because the X.21 interface definition does not include a loopback definition. |
To specify a loopback interface and enter interface configuration mode, use one of the following commands in global configuration mode:
| Command | Purpose |
|---|---|
interface loopback number | Enters interface configuration. |
interface loopback slot/port | Enters interface configuration for the Cisco7200 series or the Cisco7500 series. |
interface loopback slot/port-adapter/port | Enters interface configuration for the Cisco7500 series. |
See the "Running Interface Loopback Diagnostics" section.
The null interface provides an alternative method of filtering traffic. You can avoid the overhead involved with using access lists by directing undesired network traffic to the null interface.
To specify the null interface, use the following command in global configuration mode:
| Command | Purpose |
|---|---|
interface null 0 | Enters interface configuration. |
Specify null 0 (or null0) as the interface type and number. The null interface can be used in any command that has an interface type as an argument. The following example configures a null interface for IP route 127.0.0.0:
ip route 127.0.0.0 255.0.0.0 null 0
Tunneling provides a way to encapsulate arbitrary packets inside of a transport protocol. This feature is implemented as a virtual interface to provide a simple interface for configuration. The tunnel interface is not tied to specific "passenger" or "transport" protocols, but rather, it is an architecture that is designed to provide the services necessary to implement any standard point-to-point encapsulation scheme. Because tunnels are point-to-point links, you must configure a separate tunnel for each link.
Tunneling has the following three primary components:
Figure 21 illustrates IP tunneling terminology and concepts.
To understand the process of tunneling, consider connecting two AppleTalk networks with a non-AppleTalk backbone, such as IP. The relatively high bandwidth consumed by the broadcasting of Routing Table Maintenance Protocol (RTMP) data packets can severely hamper the backbone's network performance. This problem can be solved by tunneling AppleTalk through a foreign protocol, such as IP. Tunneling encapsulates an AppleTalk packet inside the foreign protocol packet, which is then sent across the backbone to a destination router. The destination router then removes the encapsulation from the AppleTalk packet and, if necessary, routes the packet to a normal AppleTalk network. Because the encapsulated AppleTalk packet is sent in a directed manner to a remote IP address, bandwidth usage is greatly reduced. Furthermore, the encapsulated packet benefits from any features normally enjoyed by IP packets, including default routes and load balancing.
The following are several situations where encapsulating traffic in another protocol is useful:
The following are considerations and precautions to observe when you configure tunneling:
%TUN-RECURDOWN Interface Tunnel 0 temporarily disabled due to recursive routing
To configure IP tunneling, perform the following tasks:
For commands that monitor IP tunnels, see the "Monitoring and Maintaining the Interface" section. For examples of configuring tunnels, see the "IP Tunneling Examples" section.
| Command | Purpose |
|---|---|
interface tunnel number | Enters interface configuration. |
interface tunnel slot/port | Enters interface configuration for the Cisco7200 series. |
interface tunnel slot/port-adapter/port | Enters interface configuration for the Cisco7500 series. |
You must specify the tunnel interface's source address by using the following command in interface configuration mode:
| Command | Purpose |
|---|---|
tunnel source {ip-address | type number} | Configures the tunnel source. |
|
NoteYou cannot have two tunnels using the same encapsulation mode with exactly the same source and destination address. The workaround is to create a loopback interface and source packets off the loopback interface. |
You must specify the tunnel interface's destination by using the following command in interface configuration mode:
| Command | Purpose |
|---|---|
tunnel destination {hostname | ip-address} | Configures the tunnel destination. |
| Command | Purpose |
|---|---|
tunnel mode {aurp | cayman | dvmrp | eon | gre ip | nos} | Configures the tunnel mode. |
If you are tunneling AppleTalk, you must use either the AppleTalk Update Routing Protocol (AURP), Cayman or GRE tunneling mode. Cayman tunneling is designed by Cayman Systems and enables routers and access servers to interoperate with Cayman GatorBoxes. You can have Cisco devices at either end of the tunnel, or you can have a GatorBox at one end and Cisco router or access server at the other end. Use Distance Vector Multicast Routing Protocol (DVMRP) mode when a router or access server connects to a mrouted router to run DVMRP over a tunnel. It is required to configure Protocol-Independent Multicast (PIM) and an IP address on a DVMRP tunnel.
 |
CautionDo not configure a Cayman tunnel with an AppleTalk network address. |
Some passenger protocols rely on media checksums to provide data integrity. By default, the tunnel does not guarantee packet integrity. By enabling end-to-end checksums, the CiscoIOS software drops corrupted packets. To enable such checksums on a tunnel interface, use the following command in interface configuration mode:
| Command | Purpose |
|---|---|
tunnel checksum | Configures end-to-end checksumming. |
You can optionally enable an ID key for a tunnel interface. This key must be set to the same value on the tunnel endpoints. Tunnel ID keys can be used as a form of weak security to prevent incorrect configuration or injection of packets from a foreign source.
The tunnel ID key is available with GRE only.
|
NoteWhen using GRE, the ID key is carried in each packet. We do not recommend relying on this key for security purposes. |
To configure a tunnel ID key, use the following command in interface configuration mode:
| Command | Purpose |
|---|---|
tunnel key key-number | Configures a tunnel identification key. |
You can optionally configure a tunnel interface to drop datagrams that arrive out of order. This is useful when carrying passenger protocols that function poorly when they receive packets out of order (forexample, LLC2-based protocols). This option is available with GRE only.
To use this option, use the following command in interface configuration mode:
| Command | Purpose |
|---|---|
tunnel sequence-datagrams | Configures a tunnel interface to drop out-of-order datagrams. |
Increasingly, remote users are accessing networks through dial-up telephone connections. In contrast to local users who can connect directly into the network, remote users must first dial into an access server.
The access server supports a packet tunneling strategy that extends the internetwork---in effect creating a virtual private link for the mobile user. When a user activates asynchronous host mobility, the access server on which the remote user dials into becomes a remote point-of-presence (POP) for the user's home network. Once logged in, users experience a server environment identical to the one that they experience when they connect directly to the "home" access server.
Once the network layer connection is made, data packets are tunneled at the physical and/or data link layer instead of at the protocol layer. In this way, raw data bytes from dial-in users are transported directly to the "home" access server, which processes the protocols.
Figure 24 illustrates the implementation of asynchronous host mobility on an extended internetwork. Amobile user connects to an access server on the internetwork and, by activating asynchronous host mobility, is connected to a "home" access server configured with the appropriate user name. The user sees an authentication dialog or prompt from the "home" system and can proceed as if he or she were connected directly to that device.
The remote user implements asynchronous host mobility by executing the tunnel command in user EXEC mode. The tunnel command sets up a network layer connection to the specified destination. Theaccess server accepts the connection, attaches it to a virtual terminal (VTY), and runs a command parser capable of running the normal dial-in services. After the connection is established, data is transferred between the modem and network connection with a minimum of interpretations. When communications are complete, the network connection can be closed and terminated from either end.
Refer to the Cisco Access Connection Guide for information about setting up the network layer connection with the tunnel command.
This section provides examples that illustrate configuration of IP tunnels.
The following example shows an IP tunneling configuration with commented (!) explanations:
!Creates the interface interface tunnel 0 !enables IPX on the interface novell network 1e !enables appletalk appletalk cable-range 4001-4001 128 !enables IP ip address 10.1.2.3. 255.255.255.0 !enables DECnet DECnet cost 4 !sets the source address, or interface, for packets tunnel source ethernet 0 !determines where the encapsulated packets are to go tunnel destination 131.108.14.12 !sets the protocol tunnel mode gre !computes a checksum on passenger packets if protocol does not already have reliable !checksum tunnel checksum needed !sets the id key tunnel key 42 !set to drop out of order packets tunnel sequence-datagrams
Figure 25 is an example of connecting multiprotocol subnetworks across a single-protocol backbone. Theconfigurations of Router A and Router B follow Figure 25.
Router A
interface ethernet 0 description physics department AppleTalk lan appletalk cable-range 4001-4001 32 ! interface fddi 0 description connection to campus backbone ip address 36.0.8.108 255.255.255.0 interface tunnel 0 tunnel source fddi 0 tunnel destination 36.0.21.20 appletalk cable-range 5313-5313 1
Router B
interface ethernet 0 description chemistry department appletalk lan appletalk cable-range 9458-9458 3 ! interface fddi 0 description connection to campus backbone ip address 36.0.21.20 255.255.255.0 interface tunnel 0 tunnel source fddi 0 tunnel destination 36.0.8.108 appletalk cable-range 5313-5313 2
Figure 26 is an example of routing a private IP network and a Novell network across a public serviceprovider. The configuration of Router A and Router B follow Figure 26.
Router A
interface ethernet 0 description boston office ip address 10.1.1.1 255.255.255.0 novell network 1e ! interface serial 0 description connection to NEARnet ip address 192.13.2.1 255.255.255.0 ! interface tunnel 0 tunnel source serial 0 tunnel destination 131.108.5.2 ip address 10.1.2.1 255.255.255.0 novell network 1f
Router B
interface ethernet 0 description menlo park office ip address 10.1.3.1 255.255.255.0 novell network 31 ! interface serial 4 description connection to BARRnet ip address 131.108.5.2 255.255.255.0 ! interface tunnel 0 tunnel source serial 4 tunnel destination 192.13.2.1 ip address 10.1.2.2 255.255.255.0 novell network 1f
Posted: Mon Jul 17 13:19:14 PDT 2000
Copyright 1989-2000©Cisco Systems Inc.