cc/td/doc/product/software/ios120/relnote
hometocprevnextglossaryfeedbacksearchhelp
PDF

Table of Contents

Release Notes for Cisco IOS Release 12.0(5)T1 Feature Packs for Cisco 3600 Series Routers

Release Notes for Cisco IOS Release 12.0(5)T1 Feature Packs for Cisco 3600 Series Routers

September 20, 1999

Contents

These release notes describe Cisco IOS Release 12.0(5)T1 feature packs for Cisco 3600 series routers. Use them with the documents listed in the "Related Documentation" section.

These release notes describe the following topics:

Introduction

This section explains how to use this document and describes feature pack components.

How to Use These Release Notes

The tables in these release notes contain details about Cisco feature packs. Use these tables to perform the following tasks before loading a software image onto a router:

    1. Use Table 1, "Cisco 3600 Series Routers Default Memory and Upgrade Options," to find the factory-default memory and available upgrades for your router.

    2. Use Table 2, "Feature Pack Product Numbers," to identify the software image to load.

    3. Use Table 3, "Cisco Feature Pack Image Filenames and Memory Requirements," to find the memory required for this image.

    4. Use the tables in the "Feature Set Tables" section to identify the features supported in a feature set image.

What Is a Feature Pack?

A feature pack contains the following items:

The heart of a feature pack is the CD-ROM that contains software images and the RSL, which is a Windows 95 application that loads an image onto a router or access server. Each feature pack CD-ROM contains at least one Cisco IOS feature set. The CD booklet Getting Started with the Router Software Loader explains how to use the RSL to install the router image. If you cannot use the RSL to load images, you can follow the instructions in the "Alternatives to RSL" section.

Before running the RSL, read the "Installing Software Images Using RSL" section. If you are loading software on a preconfigured router, you should save the router configuration file on your PC before beginning the image download process, as described in Getting Started with the Router Software Loader.

System Requirements

This section describes the following topics:

Memory Requirements

Table 1 describes memory requirements and upgrade options for Cisco 3600 series routers for Release 12.0(5)T1.


Table 1: Cisco 3600 Series Routers Default Memory and Upgrade Options
Memory Type Cisco 3600 Series Defaults Upgrade Options

Flash SIMM

8 MB

For the 3620 and 3640:
4-MB upgrade: MEM3600-4FS=
8-MB upgrade: MEM3600-8FS=
16-MB upgrade: MEM3600-16FS=
16-MB upgrade: MEM3600-2X8FS= (2 x 8 MB Flash SIMMs)
32-MB upgrade: MEM3600-2X16FS= (2 x 16 MB Flash SIMMs)
For the 3660:
32-MB upgrade: MEM3660-32FS=
32-MB upgrade: MEM3660-2X16FS= (2 x 16 MB Flash SIMMs)
64-MB upgrade: MEM3660-2X32FS= (2 x 32 MB Flash SIMMs)

Flash PCMCIA

0 MB

4-MB upgrade: MEM3600-4FC=
8-MB upgrade: MEM3600-8FC=
16-MB upgrade: MEM3600-16FC=

DRAM SIMM

32 MB

For the 3620:
4-MB upgrade: MEM3620-4D=
8-MB upgrade: MEM3620-8D=
16-MB upgrade: MEM3620-16D=
For the 3640:
8-MB upgrade: MEM3640-2X4D= (2 x 4 MB DRAM SIMMs)
16-MB upgrade: MEM3640-2X8D= (2 x 16 MB DRAM SIMMs)
32-MB upgrade: MEM3640-2X16D= (2 x 16 MB DRAM SIMMs)
64-MB upgrade: MEM3640-2X32D= (2 x 32 MB DRAM SIMMs)
128-MB upgrade: MEM3640-4X32D= (4 x 32 MB DRAM SIMMs)
For the 3660:
32-MB upgrade: MEM3660-32D=
128-MB upgrade: MEM3660-128D=
128-MB upgrade: MEM3660-2X64D= (2 x 64 MB DRAM SIMMs)
256-MB upgrade: MEM3660-2X128D= (2 x 128 MB DRAM SIMMs)

Hardware Supported

The Cisco 3600 series includes the Cisco 3620, Cisco 3640, and Cisco 3660 modular routers. These routers support the following LAN interfaces:

Cisco 3600 series routers support the following WAN data rates:

The routers support the following WAN interfaces:

Software Compatibility

The feature packs described in these release notes contain Cisco IOS Release 12.0(5)T1 and 12.0(5)XK1 software images, some earlier images, and RSL Version 7.6. Before running RSL, read the "Installing Software Images Using RSL" section.

Determining Your Software Release

To determine the version of Cisco IOS software that is currently running on your Cisco 3600 series router, log in to the router and enter the show version user EXEC command. The following is sample output from the show version command. The version number is indicated on the second line as shown below: 

Router> show version
Cisco Internetwork Operating System Software 
IOS (tm) 3600 Software (C3640-JS-M), Version 12.0(5)T1, RELEASE SOFTWARE

The output includes more information including processor revision numbers, memory amounts, hardware IDs, and partition information.

Updating to a New Software Release

For information about upgrading to a new software release, see the Cisco IOS Software Release 12.0 T Upgrade (#819: 1/99) product bulletin located on CCO at:

Service and Support: Product Bulletins: Software

Under Cisco IOS 12.0, click Cisco IOS Software Release 12.0 T Upgrade (#819: 1/99).

Product Number Quick-Reference List

Table 2 lists the Cisco product numbers of the feature packs supported in this release.


Table 2: Feature Pack Product Numbers
Product Number Feature Pack Description

CD36-C-12.0.5=

Cisco 3600 IP Feature Pack

CD36-CH-12.0.5=

Cisco 3600 IP/FW1 Feature Pack

CD36-CP-12.0.5=

Cisco 3600 IP Plus Feature Pack

CD36-CHL-12.0.5=

Cisco 3600 IP/FW Plus IPSec 56 Feature Pack2

CD36-CHK2-12.0.5=

Cisco 3600 IP/FW Plus IPSec 3DES Feature Pack2

CD36-CK2-12.0.5=

Cisco 3600 IP Plus IPSec 3DES Feature Pack2

CD36-CL-12.0.5=

Cisco 3600 IP Plus IPSec 56 Feature Pack2

CD36-B-12.0.5=

Cisco 3600 IP/IPX/AT/DEC Feature Pack

CD36-BP-12.0.5=

Cisco 3600 IP/IPX/AT/DEC Plus Feature Pack

CD36-BHP-12.0.5=

Cisco 3600 IP/IPX/AT/DEC/FW Plus Feature Pack

CD36-AP-12.0.5=

Cisco 3600 Enterprise Plus Feature Pack

CD36-AL-12.0.5=

Cisco 3600 Enterprise Plus IPSec 56 Feature Pack2

CD36-AHK2-12.0.5=

Cisco 3600 Enterprise/FW Plus IPSec 3DES2

CD36-AHL-12.0.5=

Cisco 3600 Enterprise/FW IPSec 56 Feature Pack2

1FW means firewall.
2This feature pack contains encryption images.

Feature Pack Overview Table

Table 3 identifies each feature pack as specified on the router software CD-ROM label, the feature sets in each feature pack, and UNIX and DOS filenames of the images, memory requirements, and RSL installer descriptions.


Table 3: Cisco Feature Pack Image Filenames and Memory Requirements
Product Number CD-ROM Title UNIX Image Name DOS Image Name Flash Memory Required Main MemoryRequired RSL Installer Description
CD36-C-12.0.5=

Cisco 3600
IP Feature Pack
Release 12.0(5)T1
RSL Version 7.6

c3620-i-mz.120-5.T1

aaa0700

8 MB

24 MB

Cisco 3620 IP Feature Set 12.0(5)T1

c3620-i-mz.120-5.XK1

aaa0701

8 MB

24 MB

Cisco 3620 IP Feature Set 12.0(5)XK1

c3620-i-mz.113-10.T

aaa0702

4 MB

16 MB

Cisco 3620 IP Feature Set 11.3(10)T

c3640-i-mz.120-5.T1

aaa0703

8 MB

24 MB

Cisco 3640 IP Feature Set 12.0(5)T1

c3640-i-mz.120-5.XK1

aaa0704

8 MB

24 MB

Cisco 3640 IP Feature Set 12.0(5)XK1

c3640-i-mz.113-10.T

aaa0705

4 MB

16 MB

Cisco 3640 IP Feature Set 11.3(10)T

c3660-i-mz.120-5.T1

aaa0706

8 MB

24 MB

Cisco 3660 IP Feature Set 12.0(5)T1

c3660-i-mz.120-5.XK1

aaa0707

8 MB

24 MB

Cisco 3660 IP Feature Set 12.0(5)XK1

CD36-CH-12.0.5=

Cisco 3600 IP/FW
Feature Pack
Release 12.0(5)T1
RSL Version 7.6

c3620-io3-mz.120-5.T1

aaa0708

8 MB

32 MB

Cisco 3620 IP/FW Feature Set 12.0(5)T1

c3620-io3-mz.120-5.XK1

aaa0709

8 MB

32 MB

Cisco 3620 IP/FW Feature Set 12.0(5)XK1

c3640-io3-mz.120-5.T1

aaa0710

8 MB

32 MB

Cisco 3640 IP/FW Feature Set 12.0(5)T1

c3640-io3-mz.120-5.XK1

aaa0711

8 MB

32 MB

Cisco 3640 IP/FW Feature Set 12.0(5)XK1

CD36-CP-12.0.5=

Cisco 3600 IP Plus
Feature Pack
Release 12.0(5)T1
RSL Version 7.6

c3620-is-mz.120-5.T1

aaa0714

8 MB

32 MB

Cisco 3620 IP Plus
Feature Set 12.0(5)T1

c3620-is-mz.120-5.XK1

aaa0715

8 MB

32 MB

Cisco 3620 IP Plus
Feature Set 12.0(5)XK1

c3620-is-mz.113-10.T

aaa0716

8 MB

24 MB

Cisco 3620 IP Plus
Feature Set 11.3(10)T

c3640-is-mz.120-5.T1

aaa0717

8 MB

32 MB

Cisco 3640 IP Plus
Feature Set 12.0(5)T1

c3640-is-mz.120-5.XK1

aaa0718

8 MB

32 MB

Cisco 3640 IP Plus
Feature Set 12.0(5)XK1

c3640-is-mz.113-10.T

aaa0719

8 MB

24 MB

Cisco 3640 IP Plus
Feature Set 11.3(10)T

c3660-is-mz.120-5.T1

aaa0720

8 MB

32 MB

Cisco 3660 IP Plus
Feature Set 12.0(5)T1

c3660-is-mz.120-5.XK1

aaa0721

8 MB

32 MB

Cisco 3660 IP Plus
Feature Set 12.0(5)XK1

CD36-CHL-12.0.5=

Cisco 3600
IP/FW Plus
IPSec 56
Feature Pack
Release 12.0(5)T1
RSL Version 7.6

c3620-io3s56i-mz.120-5.T1

aaa0722

16 MB

32 MB

Cisco 3620 IP/FW Plus IPSec 56 Feature Set 12.0(5)T1

c3620-io3s56i-mz.120-5.XK1

aaa0723

16 MB

32 MB

Cisco 3620 IP/FW Plus IPSec 56 Feature Set 12.0(5)XK1

c3640-io3s56i-mz.120-5.T1

aaa0724

16 MB

48 MB

Cisco 3640 IP/FW Plus IPSec 56 Feature Set 12.0(5)T1

c3640-io3s56i-mz.120-5.XK1

aaa0725

16 MB

48 MB

Cisco 3640 IP/FW Plus IPSec 56 Feature Set 12.0(5)XK1

CD36-CHK2-12.0.5=

Cisco 3600
IP/FW Plus IPSec 3DES
Feature Pack
Release 12.0(5)T1
RSL Version 7.6

c3620-ik2o3s-mz.120-5.T1

aaa0728

8 MB

32 MB

Cisco 3620 IP/FW Plus IPSec 3DES Feature Set 12.0(5)T1

c3620-ik2o3s-mz.120-5.XK1

aaa0729

8 MB

32 MB

Cisco 3620 IP/FW Plus IPSec 3DES Feature Set 12.0(5)XK1

c3640-ik2o3s-mz.120-5.T1

aaa0730

8 MB

32 MB

Cisco 3640 IP/FW Plus IPSec 3DES Feature Set 12.0(5)T1

c3640-ik2o3s-mz.120-5.XK1

aaa0731

8 MB

32 MB

Cisco 3640 IP/FW Plus IPSec 3DES Feature Set 12.0(5)XK1

CD36-CK2-12.0.5=

Cisco 3600
IP Plus IPSec 3DES
Feature Pack
Release 12.0(5)T1
RSL Version 7.6

c3620-ik2s-mz.120-5.T1

aaa0734

8 MB

32 MB

Cisco 3620 IP Plus IPSec 3DES
Feature Set 12.0(5)T1

c3620-ik2s-mz.120-5.XK1

aaa0735

8 MB

32 MB

Cisco 3620 IP Plus IPSec 3DES
Feature Set 12.0(5)XK1

c3640-ik2s-mz.120-5.T1

aaa0736

8 MB

32 MB

Cisco 3640 IP Plus IPSec 3DES
Feature Set 12.0(5)T1

c3640-ik2s-mz.120-5.XK1

aaa0737

8 MB

32 MB

Cisco 3640 IP Plus IPSec 3DES
Feature Set 12.0(5)XK1

c3660-ik2s-mz.120-5.T1

aaa0738

16 MB

48 MB

Cisco 3660 IP Plus IPSec 3DES
Feature Set 12.0(5)T1

c3660-ik2s-mz.120-5.XK1

aaa0739

16 MB

48 MB

Cisco 3660 IP Plus IPSec 3DES
Feature Set 12.0(5)XK1

CD36-CL-12.0.5=

Cisco 3600
IP Plus IPSec 56
Feature Pack
Release 12.0(5)T1
RSL Version 7.6

c3620-is56i-mz.120-5.T1

aaa0740

8 MB

32 MB

Cisco 3620 IP Plus IPSec 56
Feature Set 12.0(5)T1

c3620-is56i-mz.120-5.XK1

aaa0741

8 MB

32 MB

Cisco 3620 IP Plus IPSec 56
Feature Set 12.0(5)XK1

c3620-is56i-mz.113-10.T

aaa0742

8 MB

32 MB

Cisco 3620 IP Plus IPSec 56
Feature Set 11.3(10)T

c3640-is56i-mz-120-5.T1

aaa0743

8 MB

32 MB

Cisco 3640 IP Plus IPSec 56
Feature Set 12.0(5)T1

c3640-is56i-mz-120-5.XK1

aaa0744

8 MB

32 MB

Cisco 3640 IP Plus IPSec 56
Feature Set 12.0(5)XK1

c3640-is56i-mz-113-10.T

aaa0745

8 MB

32 MB

Cisco 3640 IP Plus IPSec 56
Feature Set 11.3(10)T

c3660-is56i-mz-120-5.T1

aaa0746

8 MB

32 MB

Cisco 3660 IP Plus IPSec 56
Feature Set 12.0(5)T1

c3660-is56i-mz-120-5.XK1

aaa0747

8 MB

32 MB

Cisco 3660 IP Plus IPSec 56
Feature Set 12.0(5)XK1

CD36-B-12.0.5=

Cisco 3600
IP/IPX/AT/DEC
Feature Pack
Release 12.0(5)T1
RSL Version 7.6

c3620-d-mz.120-5.T1

aaa0748

8 MB

24 MB

Cisco 3620 IP/IPX/AppleTalk Feature Set 12.0(5)T1

c3620-d-mz.120-5.XK1

aaa0749

8 MB

24 MB

Cisco 3620 IP/IPX/AppleTalk Feature Set 12.0(5)XK1

c3620-d-mz.113-10.T

aaa0750

8 MB

24 MB

Cisco 3620 IP/IPX/AppleTalk Feature Set 11.3(10)T

c3640-d-mz-120-5.T1

aaa0751

8 MB

24 MB

Cisco 3640 IP/IPX/AppleTalk Feature Set 12.0(5)T1

c3640-d-mz-120-5.XK1

aaa0752

8 MB

24 MB

Cisco 3640 IP/IPX/AppleTalk Feature Set 12.0(5)XK1

c3640-d-mz-113-10.T

aaa0753

8 MB

24 MB

Cisco 3640 IP/IPX/AppleTalk Feature Set 113-10.T

c3660-d-mz-120-5.T1

aaa0754

8 MB

24 MB

Cisco 3660 IP/IPX/AppleTalk Feature Set 12.0(5)T1

c3660-d-mz-120-5.XK1

aaa0755

8 MB

24 MB

Cisco 3660 IP/IPX/AppleTalk Feature Set 12.0(5)XK1

CD36-BP-12.0.5=

Cisco 3600
IP/IPX/AT/DEC Plus
Feature Pack
Release 12.0(5)T1
RSL Version 7.6

c3620-ds-mz.120-5.T1

aaa0756

16 MB

32 MB

Cisco 3620 IP/IPX/AT Plus
Feature Set 12.0(5)T1

c3620-ds-mz.120-5.XK1

aaa0757

16 MB

32 MB

Cisco 3620 IP/IPX/AT Plus
Feature Set 12.0(5)XK1

c3620-ds-mz.113-10.T

aaa0758

8 MB

32 MB

Cisco 3620 IP/IPX/AT Plus
Feature Set 11.3(10)T

c3640-ds-mz.120-5.T1

aaa0759

16 MB

32 MB

Cisco 3640 IP/IPX/AT Plus
Feature Set 12.0(5)T1

c3640-ds-mz.120-5.XK1

aaa0760

16 MB

32 MB

Cisco 3640 IP/IPX/AT Plus
Feature Set 12.0(5)XK1

c3640-ds-mz.113-10.T

aaa0761

8 MB

32 MB

Cisco 3640 IP/IPX/AT Plus
Feature Set 11.3(10)T

c3660-ds-mz.120-5.T1

aaa0762

16 MB

32 MB

Cisco 3660 IP/IPX/AT Plus
Feature Set 12.0(5)T1

c3660-ds-mz.120-5.XK1

aaa0763

16 MB

32 MB

Cisco 3660 IP/IPX/AT Plus
Feature Set 12.0(5)XK1

CD36-BHP-12.0.5=

Cisco 3600
IP/IPX/AT/DEC/
FW Plus
Feature Pack
Release 12.0(5)T1
RSL Version 7.6

c3620-do3s-mz.120-5.T1

aaa0764

16 MB

32 MB

Cisco 3620 IP/IPX/AT/DECnet/
FW Plus
Feature Set 12.0(5)T1

c3620-do3s-mz.120-5.XK1

aaa0765

16 MB

32 MB

Cisco 3620 IP/IPX/AT/DECnet/
FW Plus
Feature Set 12.0(5)XK1

c3640-do3s-mz.120-5.T1

aaa0766

16 MB

48 MB

Cisco 3640 IP/IPX/AT/DECnet/
FW Plus
Feature Set 12.0(5)T1

c3640-do3s-mz.120-5.XK1

aaa0767

16 MB

48 MB

Cisco 3640 IP/IPX/AT/DECnet/
FW Plus
Feature Set 12.0(5)XK1

CD36-AP-12.0.5=

Cisco 3600
Enterprise Plus
Feature Pack
Release 12.0(5)T1
RSL Version 7.6

c3620-js-mz.120-5.T1

aaa0770

16 MB

48 MB

Cisco 3620
Enterprise Plus
Feature Set 12.0(5)T1

c3620-js-mz.120-5.XK1

aaa0771

16 MB

48 MB

Cisco 3620
Enterprise Plus
Feature Set 12.0(5)XK1

c3620-js-mz.113-10.T

aaa0772

8 MB

32 MB

Cisco 3620
Enterprise Plus
Feature Set 11.3(10)T

c3640-js-mz.120-5.T1

aaa0773

16 MB

48 MB

Cisco 3640
Enterprise Plus
Feature Set 12.0(5)T1

c3640-js-mz.120-5.XK1

aaa0774

16 MB

48 MB

Cisco 3640
Enterprise Plus
Feature Set 12.0(5)XK1

c3640-js-mz.113-10.T

aaa0775

8 MB

32 MB

Cisco 3640
Enterprise Plus
Feature Set 11.3(10)T

c3660-js-mz.120-5.T1

aaa0776

16 MB

48 MB

Cisco 3660
Enterprise Plus
Feature Set 12.0(5)T1

c3660-js-mz.120-5.XK1

aaa0777

16 MB

48 MB

Cisco 3660
Enterprise Plus
Feature Set 12.0(5)XK1

CD36-AL-12.0.5=

Cisco 3600
Enterprise Plus IPSec 56
Feature Pack
Release 12.0(5)T1
RSL Version 7.6

c3620-js56i-mz.120-5.T1

aaa0786

16 MB

48 MB

Cisco 3620 Enterprise Plus IPSec 56
Feature Set 12.0(5)T1

c3620-js56i-mz.120-5.XK1

aaa0787

16 MB

48 MB

Cisco 3620 Enterprise Plus IPSec 56
Feature Set 12.0(5)XK1

c3620-js56i-mz.113-10.T

aaa0788

8 MB

32 MB

Cisco 3620 Enterprise Plus IPSec 56
Feature Set 11.3(10)T

c3640-js56i-mz.120-5.T1

aaa0789

16 MB

48 MB

Cisco 3640 Enterprise Plus IPSec 56
Feature Set 12.0(5)T1

c3640-js56i-mz.120-5.XK1

aaa0790

16 MB

48 MB

Cisco 3640 Enterprise Plus IPSec 56
Feature Set 12.0(5)XK1

c3640-js56i-mz.113-10.T

aaa0791

8 MB

32 MB

Cisco 3640 Enterprise Plus IPSec 56
Feature Set 11.3(10)T

c3660-js56i-mz.120-5.T1

aaa0792

16 MB

48 MB

Cisco 3660 Enterprise Plus IPSec 56
Feature Set 12.0(5)T1

c3660-js56i-mz.120-5.XK1

aaa0793

16 MB

48 MB

Cisco 3660 Enterprise Plus IPSec 56
Feature Set 12.0(5)XK1

CD36-AHK2-12.0.5=

Cisco 3600
Enterprise/FW Plus IPSec 3DES
Feature Pack
Release 12.0(5)T1
RSL Version 7.6

c3620-jk2o3s-mz.120-5.T1

aaa0794

16 MB

48 MB

Cisco 3620 Enterprise/FW Plus IPSec 3DES Feature Set 12.0(5)T1

c3620-jk2o3s-mz.120-5.XK1

aaa0795

16 MB

48 MB

Cisco 3620 Enterprise/FW Plus IPSec 3DES Feature Set 12.0(5)XK1

c3640-jk2o3s-mz.120-5.T1

aaa0796

16 MB

48 MB

Cisco 3640 Enterprise/FW Plus IPSec 3DES Feature Set 12.0(5)T1

c3640-jk2o3s-mz.120-5.XK1

aaa0797

16 MB

48 MB

Cisco 3640 Enterprise/FW Plus IPSec 3DES Feature Set 12.0(5)XK1

CD36-AHL-12.0.5=

Cisco 3600
Enterprise/FW Plus IPSec 56
Feature Pack
Release 12.0(5)T1
RSL Version 7.6

c3620-jo3s56i-mz.120-5.T1

aaa0800

16 MB

48 MB

Cisco 3620 Enterprise/FW Plus IPSec 56 Feature Set 12.0(5)T1

c3620-jo3s56i-mz.120-5.XK1

aaa0801

16 MB

48 MB

Cisco 3620 Enterprise/FW Plus IPSec 56 Feature Set 12.0(5)XK1

c3640-jo3s56i-mz.120-5.T1

aaa0802

16 MB

48 MB

Cisco 3640 Enterprise/FW Plus  IPSec 56
Feature Set 12.0(5)T1

c3640-jo3s56i-mz.120-5.XK1

aaa0803

16 MB

48 MB

Cisco 3640 Enterprise/FW Plus  IPSec 56
Feature Set 12.0(5)XK1

Feature Set Tables

Cisco IOS software is packaged as feature sets (or images), each containing a subset of Cisco IOS features. The following conventions identify feature sets:

Cisco IOS images with strong encryption (including, but not limited to, 56-bit and 168-bit DES) are subject to U.S. government export controls and have a limited distribution. Images to be installed outside the U.S. require an export license. Customer orders might be denied or subject to delay due to U.S. government regulations. Contact your sales representative or distributor for more information, or send e-mail to export@cisco.com.

The following list shows feature sets supported on Cisco 3600 series routers by Cisco IOS Releases 12.0(5)T1 and 12.0(5)XK1:

Table 4 and Table 5 list features supported by Cisco 3600 series routers in each Cisco IOS Release 12.0(5)T1 and 12.0(5)XK1 feature set.


Table 4: Features by Feature Set for the Cisco 3600 Series, Part 1 of 2
Features Feature Sets
IP IP/FW IP Plus IP/FW Plus IPSec 56 IP/FW Plus IPSec 3DES IP Plus IPSec 3DES IP Plus IPSec 56
New Features in 12.0(5)XK

High Density Voice Network Modules

Yes

Yes

Yes

Yes

Yes

Yes

Yes

T1/E1
Inverse Multiplexing for ATM
Network Modules

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Connectivity
Layer 2 Tunnel Protocol (L2TP)

No

No

Yes

No

Yes

Yes

Yes

L2TP Dial Out

No

No

Yes

No

Yes

Yes

Yes

RIP Enhancements

Yes

Yes

Yes

Yes

Yes

Yes

Yes

SNMP version 3

Yes

Yes

Yes

Yes

Yes

Yes

Yes

IBM Support
DLSw+ RSVP

No

No

Yes

Yes

Yes

Yes

Yes

DLSw+ Enhanced Load Balancing

No

No

Yes

Yes

Yes

Yes

Yes

DLSw+ Peer Clusters

No

No

Yes

Yes

Yes

Yes

Yes

DLSw+ Ethernet Redundancy

No

No

Yes

Yes

Yes

Yes

Yes

Token Ring Interswitch Link

Yes

No

Yes

Yes

No

Yes

Yes

IP /IPX Routing
Airline Product Set

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Async over UDP

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Easy IP Phase 2- DHCP Server

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Flow Random Early Detection

Yes

Yes

Yes

Yes

Yes

Yes

Yes

IS-IS Multiarea Support

No

No

No

No

No

No

No

Multilayer Switching for IP Multicast

No

No

Yes

Yes

Yes

Yes

Yes

Multilayer Switching for IPX

Yes

Yes

Yes

Yes

Yes

Yes

Yes

OSPF Packet Pacing

Yes

Yes

Yes

Yes

Yes

Yes

Yes

OS_IFSS

Yes

Yes

Yes

Yes

Yes

Yes

Yes

PGM Router Assist

No

No

No

No

No

No

No

Service Assurance Agent (formerly Response Time Reporter)

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Web Cache Communications Protocol V2

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Management
Inverse Multiplexing for ATM
Network Modules

No

No

Yes

Yes

Yes

Yes

Yes

CNS Client for Cisco IOS Software

No

No

No

Yes

Yes

Yes

Yes

CNS Client for Cisco IOS (IP Sec Policy Agent II)

No

No

No

No

No

No

No

1FE2P Network Modules

Yes

Yes

Yes

Yes

Yes

Yes

Yes

ISDN MIB RFC 2127

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Multicast Routing Monitor

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Network Director Forwarding Agent

No

No

Yes

Yes

Yes

Yes

Yes

OC3 Network Module

No

No

Yes

Yes

Yes

Yes

Yes

Process MIB

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Subnetwork Bandwidth Manager

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Quality of Service
CLI String Search

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Parse Bookmarks

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Security
IOS Firewall Feature Set

No

Yes

No

Yes

Yes

No

No

Switching
Cisco IOS STP Enhancements

No

No

Yes

Yes

Yes

Yes

Yes

Voice
BRI Voice over IP: VIC-2BRI-S/T-TE

No

No

Yes

Yes

Yes

Yes

Yes

Voice over Frame Relay Enhancements

No

No

Yes

Yes

Yes

Yes

Yes

WAN Services
Annex-G (X.25 over Frame Relay)

Yes

Yes

Yes

Yes

Yes

Yes

Yes

ATM OC3 Networ Module

No

No

Yes

Yes

Yes

Yes

Yes

ATM LANE FSSR Protocol

No

No

Yes

Yes

Yes

Yes

Yes

DNS for X.25

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Frame Relay End-to-End Keepalive

Yes

Yes

Yes

Yes

Yes

Yes

Yes

IOS IEEE 802.1Q Support

No

No

Yes

Yes

Yes

Yes

Yes

ISDN Dynamic Multiple Encaps for Dial-in

Yes

Yes

Yes

Yes

Yes

Yes

Yes

ISDN LAPB-TA

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Mobile IP

No

No

Yes

Yes

Yes

Yes

Yes

Modem over ISDN BRI1

Yes

Yes

Yes

Yes

Yes

Yes

Yes

PPP over Frame Relay

Yes

No

Yes

No

No

Yes

Yes

Time-Based Access Lists

Yes

No

Yes

No

No

Yes

Yes

X.25 Load Balancing

Yes

Yes

Yes

Yes

Yes

Yes

Yes

1Cisco 3640 router only.


Table 5: Features by Feature Set for the Cisco 3600 Series, Part 2 of 2
Features Feature Sets
IP/IPX/
AT/DEC 		IP/IPX/
AT/DEC Plus 		IP/IPX/AT/DEC/FW Plus Enter-prise Plus Enterprise Plus
IPSec 56 		Enterprise/
FW Plus IPSec 3DES 		Enterprise/
FW IPSec 56
New Features in 12.0(5)XK

High Density Voice
Network Modules

Yes

Yes

Yes

Yes

Yes

Yes

Yes

T1/E1 Inverse Multiplexing for ATM Network Modules

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Connectivity
Layer 2 Tunnel Protocol (L2TP)

No

Yes

Yes

Yes

Yes

Yes

Yes

L2TP Dialout

No

Yes

Yes

Yes

Yes

Yes

Yes

RIP Enhancements

No

Yes

Yes

Yes

Yes

Yes

Yes

SNMP version 3

Yes

Yes

Yes

Yes

Yes

Yes

Yes

IBM Support
DLSw+ RSVP

No

Yes

Yes

Yes

Yes

No

No

DLSw+ Enhanced Load Balancing

No

Yes

Yes

Yes

Yes

No

No

DLSw+ Ethernet Redundancy

No

Yes

Yes

Yes

Yes

Yes

Yes

DLSw+ Peer Clusters

No

Yes

Yes

Yes

Yes

No

No

Token Ring Interswitch Link

Yes

Yes

No

Yes

Yes

No

No

IP/IPX Routing
Airline Product Set

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Async over UDP

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Easy IP Phase 2-DHCP Server

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Flow Random Early Detection

Yes

Yes

Yes

Yes

Yes

Yes

Yes

IS-IS Multiarea Support

No

No

No

Yes

Yes

Yes

Yes

Multilayer Switching for IP Multicast

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Multilayer Switching for IPX

Yes

Yes

Yes

Yes

Yes

Yes

Yes

OSPF Packet Pacing

Yes

Yes

Yes

Yes

Yes

Yes

Yes

OS_IFSS

Yes

Yes

Yes

Yes

Yes

Yes

Yes

PGM Router Assist

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Service Assurance Agent (formerly Response Time Reporter Enhancements)

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Web Cache Communications Protocol V2 (WCCPv2)

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Management
Inverse Multiplexing for ATM
Network Modules

No

Yes

Yes

Yes

Yes

Yes

Yes

CNS Client for Cisco IOS Software

No

No

No

Yes

Yes

No

No

CNS Client for Cisco IOS (IP Sec Policy Agent II)

No

No

No

Yes

Yes

Yes

Yes

1FE2P Network Module

Yes

Yes

Yes

Yes

Yes

Yes

Yes

ISDN MIB RFC 2127

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Multicast Routing Monitor

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Network Director Forwarding Agent

No

Yes

Yes

Yes

Yes

Yes

Yes

OC3 Network Module

No

Yes

Yes

Yes

Yes

Yes

Yes

Process MIB

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Subnetwork Bandwidth Manager

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Quality of Service
CLI String Search

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Parse Bookmarks

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Switching
Cisco IOS STP Enhancements

No

Yes

Yes

Yes

Yes

Yes

Yes

Voice
BRI Voice over IP: VIC-2BRI-S/T-TE

No

Yes

Yes

Yes

Yes

Yes

Yes

Voice over Frame Relay Enhancements

No

Yes

Yes

Yes

Yes

Yes

Yes

WAN Services
Annex-G (X.25 over Frame Relay)

Yes

Yes

Yes

Yes

Yes

Yes

Yes

ATM OC3 Network Module

No

Yes

Yes

Yes

Yes

Yes

Yes

ATM LANE FSSR Protocol

No

Yes

Yes

Yes

Yes

Yes

Yes

DNS for X.25

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Frame Relay End-to-End Keepalive

Yes

Yes

Yes

Yes

Yes

Yes

Yes

ISDN Dynamic Multiple Encapsulations for Dial-in

Yes

Yes

Yes

Yes

Yes

Yes

Yes

IOS IEEE 802.1Q Support

Yes

Yes

Yes

Yes

Yes

Yes

Yes

ISDN LAPB-TA

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Mobile IP

No

Yes

Yes

Yes

Yes

Yes

Yes

Modem over ISDN BRI1

No

Yes

Yes

Yes

Yes

Yes

Yes

PPP over Frame Relay

Yes

Yes

No

Yes

Yes

Yes

Yes

Time-Based Access Lists

Yes

Yes

No

Yes

Yes

Yes

Yes

X.25 Load Balancing

Yes

Yes

Yes

Yes

Yes

Yes

Yes

1Cisco 3640 router only.

Installation Notes

This section describes the following topics:

Installing Software Images Using RSL

This section describes some solutions to problems you might encounter when installing software images using RSL. These solutions are additions to the RSL online help.

Note If you are installing software on a Cisco 3660 router, always use the latest version of RSL.

Recovering from a Connection Error

This installation tip provides a possible recovery solution if you are unable to connect to your router. You can skip this section unless you are experiencing a connection error.

In some cases, you might receive the following error message while connecting to the target router:

"Failed to configure the router to enable the Cisco IOS software image and configuration file upload and download operations. You may want to check the router to make sure that the selected interface exists."

If you encounter this message, especially if you are connecting to a router that has a large configuration file or many interfaces, try increasing the Short Timeout to a value higher than 25 seconds in the Options dialog box.

Note Increasing the Short Timeout value might increase the time it takes for RSL to connect to the target access server.

Restoring the Startup Configuration

In some cases, the RSL is unable to restore the startup configuration. If this happens, take the following steps:

Step 1 Ensure that all cables are properly attached to both the router and the PC.

Step 2 Restart the RSL, and connect by using the Preconfigured router option.

Step 3 When asked if you want to overwrite the existing startup configuration file, choose no.

Step 4 When asked if you want to continue, choose yes.

Step 5 When the router is connected, select Download Router Configuration in the Router Software Loader dialog box.

Step 6 Select the appropriate file, and click the Copy configuration to the router nonvolatile memory button.

The router should now contain the startup configuration it had before the initial RSL connection. You can now exit the RSL.

Note In the previous situation, the router configuration register (config-register 0xnnnn) is not restored.
Note If you press Ctrl-Alt-Del to terminate the RSL, the router configuration and configuration register are not restored. However, in this case, the configuration file is not deleted from the PC, so you can restore it using the previous steps, beginning with Step 2.

Installation Tips

The following information about RSL operations can help you with the installation process:

Alternatives to RSL

The RSL is designed to work with a PC running Microsoft Windows 95 and is the recommended method for downloading software to the router. The booklet included with the CD-ROM explains how to perform this simple install process; however, two alternatives are available for installing router software:

Installing the Router Software Using the Console or Auxiliary Port

This section explains how to use the copy xmodem flash command to install the router software from the CD-ROM on the router.

Note The transfer takes place only on the port at which you enter the command. If you download via the console, all console output is discarded for the duration of the transfer. You can only download files to the router; you cannot copy files from the router. Cisco recommends using the auxiliary port for this type of software download. The auxiliary port has hardware flow control and full modem control. In addition, the transfer does not occupy the system console so it is free for other uses.

The following example shows how to use the copy xmodem flash command on a Cisco 3600 series router: 

Router# copy xmodem flash
                               **** WARNING ****
       x/ymodem is a slow transfer protocol limited to the current speed
       settings of the auxiliary/console ports. The use of the auxiliary
       port for this download is strongly recommended.
       During the course of the download no exec input/output will be
       available.
                               ---- ******* ----
       Proceed? [confirm] yes
       Use crc block checksumming? [confirm] yes
       Max Retry Count [10]: 
       Perform image validation checks? [confirm] yes
       Xmodem download using crc checksumming with image validation
       Continue? [confirm] yes
       Partition   Size    Used      Free      Bank-Size  State          Copy Mode
         1         4096K   3259K      836K     4096K      Read/Write     Direct
         2         4096K      0K     4095K     4096K      Read/Write     Direct
 
       [Type ?<no> for partition directory; ? for full directory; q to abort]
       Which partition? [default = 1] 2
 
       System flash directory, partition 2:
       File  Length   Name/status
         1   68       TESTFILE  
       [132 bytes used, 4194172 available, 4194304 total]
       Destination file name? c3620-i-mz.0918
       Erase flash device before writing? [confirm] yes
       Flash contains files. Are you sure you want to erase? [confirm]y
 
       Copy '' from server
         as 'c3620-i-mz.0918' into Flash WITH erase? [yes/no] yes
       Erasing device... eeeeeeeeeeeeeeee ...erased
       Ready to receive file...........C
       Verifying checksum...  OK (0x5DE8)
       Flash device copy took 00:12:06 [hh:mm:ss]

Installing the Router Software Using a TFTP Server Application

Use this TFTP server application method as an alternative to using the RSL to install the router software from the CD-ROM. You can perform this procedure using a PC (running Microsoft Windows 95 or Microsoft Windows 3.1), a Macintosh, or a UNIX system. You can use either the copy tftp flash or copy rcp flash command to download the router software to the router.

First, obtain a TFTP application or a remote copy protocol (rcp) application to set up your computer as a TFTP server or an rcp server. Use the RSL or the TFTP server included on the feature pack CD-ROM to install the router software only if you are using a PC running Windows 95.

Note To install software on a Cisco 3660 router, you need TFTP server version 1.1 or later.

For other operating systems, a number of TFTP or rcp applications are available from independent software vendors or available as shareware from public sources on the World Wide Web.

Note To use an rcp application, follow the same procedure below, substituting "rcp" for "TFTP" and using the copy rcp flash command instead of the copy tftp flash command.

Step 1 Install any TFTP server application on the PC. (A PC application is included on the feature pack CD-ROM for Microsoft Windows 95 only.)

Step 2 Launch the TFTP server application on the PC, usually by double-clicking the application icon or its .exe filename.

Step 3 Set up the PC as a TFTP server by using the TFTP server application setup or configuration facility.

Most TFTP server applications include a setup facility that allows you to specify the PC as a server. For example, from the TFTP menu of one application, you can select Settings to display a panel, and configure the local PC as a server by selecting the Server checkbox.

The TFTP server also allows the selection of a "root" directory. You must select the directory in which the Cisco IOS files reside (for example, d:\cpswinst\images).

Caution Make sure you set up your local PC as a TFTP server. If you overlook this step, you cannot perform the copy procedure. This reminder applies to both TFTP and rcp.

Step 4 Establish a console session from your local PC (which is now configured as a TFTP server) to the Cisco router by using one of these methods:

This is the recommended method.When you reload the router with the new image in Step 16, you remain connected to the router. (If you use Telnet, you lose connection to the router.)

Step 5 Connect your PC Ethernet port to the corresponding router LAN port. Use the 10BaseT crossover cable to connect to an Ethernet port. Use straight-through cables if you are connecting via a 10BaseT hub or a 100BaseT hub.

Step 6 Enter the following commands to set the configuration register to 0x2101 and reload to the bootstrap image:

Router# config terminal
Router(config)# config-reg 0x2101
Router(config)# end
Router# reload

Step 7 When asked whether the system configuration has been modified, enter yes:

# System configuration has been modified. Save? yes

Step 8 If the password prompt appears, enter the password:

Password: password

Step 9 At the router prompt, enter enable and then the password:

Router(boot)> enable
Password: password

Step 10 Copy the new software image from the PC CD-ROM drive to the router:

Router(boot)(config)# copy tftp flash

In the next series of steps, you download the Cisco IOS Release 12.0(5)T1 images that you want installed on your router.

Step 11 When prompted, enter the IP address of your PC, as in the following example:

Address or name of remote host [255.255.255.255]? 131.108.1.1

This is the IP address of your local PC, not that of the router.

Step 12 When prompted, enter the filename of the Cisco IOS Release 12.0(5)T1 image to be copied to the router, as in the following example:

Source file name? aaa703.bin

This example specifies the DOS image name of the IP feature set for Cisco 3600 series routers (as shown in Table 3).

Step 13 In response to the prompt, enter the destination UNIX image filename, and press Enter.

This is the name of the image file on the router, not the full pathname of the image on the CD-ROM attached to the PC. Refer to Table 3 for the UNIX image filename.

Destination file name [aaa703.bin]? c3640-i-l

During the transfer process, the software displays messages indicating that it has accessed the file you have specified and is loading it.

Step 14 Enter yes in response to the prompt asking if you want to erase the existing image resident in the router Flash memory before copying the new one.

Erase flash device before writing? [confirm] yes

The entire copying process takes several minutes and differs from network to network.

The exclamation point (!) indicates that the copy process is taking place. Each exclamation point (!) indicates that ten packets have been transferred successfully. A checksum verification of the image occurs after the image is written to Flash memory.

Step 15 Enter the following commands to reset the configuration register to 0x2102:

Router(boot)(config)# config terminal
Router(boot)(config)# config-reg 0x2102
Router(boot)(config)# end

Step 16 Enter the reload command to reload the router:

Router# reload

After reload is complete, the router should be running the required Cisco IOS image. Use the show version command to verify.

Related Documentation

This section describes the documentation related to the Cisco 3600 series, typically including hardware installation guides, software installation guides, Cisco IOS configuration and command references, system error messages, and feature modules that are updates to the Cisco IOS documentation set. Documentation is available as printed manuals or electronic documents, except for the feature modules, which are available online only.

The most current documentation can be found on the Web via Cisco Connection Online (CCO) and on the latest Documentation CD-ROM. These electronic documents might contain updates and modifications made after the paper documents were printed. See the "Cisco Connection Online" section and the "Documentation CD-ROM" section for more information.

This section contains the following subsections:

Release-Specific Documents

The following documents are specific to Release12.0 T. They are located on CCO and the Documentation CD-ROM:

To access the cross-platform Release Notes for Cisco IOS Release 12.0 T on CCO, follow this path:
Service and Support: Technical Documents: Documentation Home Page: Cisco IOS Software Configuration: Cisco IOS Release 12.0: Release Notes: Cross-Platform Release Notes for Cisco IOS Release 12.0 T
To access the cross-platform Release Notes for Cisco IOS Release 12.0 T on the Documentation CD-ROM, follow this path:
Cisco IOS Software Configuration: Cisco IOS Release 12.0: Release Notes: Cross-Platform Release Notes for Cisco IOS Release 12.0 T
To access these documents, refer to the Software Center at this path on CCO:
Service & Support: Technical Documents
For caveat details, see the Caveats for Cisco IOS Release 12.0 T document, which contains caveats applicable to all platforms for all maintenance releases of Release 12.0 T.
To access the caveat document on CCO, follow this path:
Service and Support: Technical Documents: Documentation Home Page: Cisco IOS Software Configuration: Cisco IOS Release 12.0: Release Notes: Caveats: Caveats for Cisco IOS Release 12.0 T
To access the caveat document on the Documentation CD-ROM, follow this path:
Cisco IOS Software Configuration: Cisco IOS Release 12.0: Release Notes: Caveats: Caveats for Cisco IOS Release 12.0 T
Note If you have an account with CCO, you can use Bug Navigator II to find caveats of any severity for any release. Bug Navigator II can be found at http://www.cisco.com/support/bugtools, or from CCO, select Service & Support: Online Technical Support: Software Bug Toolkit.

Platform-Specific Documents

The following list contains documents specific to Cisco 3600 series routers. These documents are available on CCO and the Documentation CD-ROM.

To access these documents on CCO, follow this path:

Service and Support: Technical Documents: Documentation Home Page: Access Servers and Access Routers: Modular Access Routers: Cisco 3600 Series Routers

To access these documents on the Documentation CD-ROM, follow this path:

Cisco IOS Software Configuration: Access Servers and Access Routers: Modular Access Routers: Cisco 3600 Series Routers

Feature Modules

Feature modules describe new features and are available online only. The information is added to the Cisco IOS documentation set before the next printing. Feature modules include an overview, benefits, configuration tasks, and command reference.

To access feature modules on CCO, follow this path:

Service and Support: Technical Documents: Documentation Home Page: Cisco IOS Software Configuration: Cisco IOS Release 12.0: New Feature Documentation

To access feature modules on the documentation CD-ROM, follow this path:

Cisco IOS Software Configuration: Cisco IOS Release 12.0: New Feature Documentation

Cisco IOS Documentation Set

The Cisco IOS software documentation set consists of Cisco IOS configuration guides, Cisco IOS command references, and several other supporting documents. These documents are shipped with your order in electronic form on the Documentation CD-ROM, unless you order the printed versions.

Documentation Modules

Each module in the Cisco IOS documentation set consists of two books: a configuration guide and a corresponding command reference. Chapters in a configuration guide describe protocols, configuration tasks, and Cisco IOS software functionality and contain comprehensive configuration examples. Chapters in a command reference provide complete command syntax information. Each configuration guide can be used in conjunction with its corresponding command reference.

To access these documents on CCO, follow this path:

Service and Support: Technical Documents: Documentation Home Page: Cisco IOS Software Configuration: Cisco IOS Release 12.0: Cisco IOS Release 12.0 Configuration Guides and Command References

To access these documents on the Documentation CD-ROM, follow this path:

Cisco IOS Software Configuration: Cisco IOS Release 12.0: Cisco IOS Release 12.0 Configuration Guides and Command References

Release 12.0 Documentation Set

Table 6 details the contents of the Cisco IOS Release 12.0 software documentation set. The document set is available in electronic form, and also in printed form upon request.

Note The most current Cisco IOS documentation can be found on the latest Documentation CD-ROM and on the Web. These electronic documents might contain updates and modifications made after the paper documents were printed.

To access the Cisco IOS documentation set on CCO, follow this path:

Service and Support: Technical Documents: Documentation Home Page: Cisco IOS Software Configuration: Cisco IOS Release 12.0

To access the Cisco IOS documentation set on the Documentation CD-ROM, follow this path:

Cisco IOS Software Configuration: Cisco IOS Release 12.0


Table 6: Cisco IOS Software Release 12.0 Documentation Set
Books Chapter Topics

  • Configuration Fundamentals Configuration Guide

  • Configuration Fundamentals Command Reference

Configuration Fundamentals Overview
Cisco IOS User Interfaces
File Management
System Management

  • Bridging and IBM Networking Configuration Guide

  • Bridging and IBM Networking Command Reference

Transparent Bridging
Source-Route Bridging
Token Ring Inter-Switch Link
Remote Source-Route Bridging
DLSw+
STUN and BSTUN
LLC2 and SDLC
IBM Network Media Translation
DSPU and SNA Service Point
SNA Frame Relay Access Support
APPN
Cisco Database Connection
NCIA Client/Server Topologies
Cisco Mainframe Channel Connection
Airline Product Set

  • Dial Solutions Configuration Guide

  • Dial Solutions Command Reference

Dial-In Port Setup
Dial-In Terminal Services
Dial-on-Demand Routing (DDR)
Dial Backup
Dial-Out Modem Pooling
Large-Scale Dial Solutions
Cost-Control Solutions
ISDN
X.25 over ISDN
VPDN
Dial Business Solutions and Examples

  • Cisco IOS Interface Configuration Guide

  • Cisco IOS Interface Command Reference

Interface Configuration Overview

  • Network Protocols Configuration Guide, Part 1

  • Network Protocols Command Reference, Part 1

IP Addressing
IP Services
IP Routing Protocols

  • Network Protocols Configuration Guide, Part 2

  • Network Protocols Command Reference, Part 2

AppleTalk
Novell IPX

  • Network Protocols Configuration Guide, Part 3

  • Network Protocols Command Reference, Part 3

Apollo Domain
Banyan VINES
DECnet
ISO CLNS
XNS

  • Security Configuration Guide

  • Security Command Reference

AAA Security Services
Security Server Protocols
Traffic Filtering and Firewalls
IP Security and Encryption
Passwords and Privileges
Neighbor Router Authentication
IP Security Options

  • Cisco IOS Switching Services Configuration Guide

  • Cisco IOS Switching Services Command Reference

Switching Paths for IP Networks
Virtual LAN (VLAN) Switching and Routing

  • Wide-Area Networking Configuration Guide

  • Wide-Area Networking Command Reference

ATM
Frame Relay
SMDS
X.25 and LAPB

  • Voice, Video, and Home Applications Configuration Guide

  • Voice, Video, and Home Applications Command Reference

Voice over IP
Voice over Frame Relay
Voice over ATM
Voice over HDLC
Video Support
Universal Broadband Features

  • Quality of Service Solutions Configuration Guide

  • Quality of Service Solutions Command Reference

Classification
Scheduling
Packet Drop
Traffic Shaping
ATM QoS
SNA QoS
Line Protocols

  • Cisco IOS Software Command Summary

  • Dial Solutions Quick Configuration Guide

  • System Error Messages

  • Debug Command Reference

Note The Cisco Management Information Base (MIB) User Quick Reference publication is no longer being published. For the latest list of MIBs supported by Cisco, see the Cisco Network Management Toolkit on Cisco Connection Online. On CCO, go to Software and Support: Software Center: Network Management Products: Cisco Network Management Toolkit: Cisco MIBs.

Service and Support

The following URL contains links and helpful tips on configuring your Cisco products: http://www.cisco.com/kobayashi/serv_tips.shtml.

This URL is subject to change without notice. You can also access this page by following this path from CCO:

Products & Technologies: Technical Tips

"Hot Tips" are popular tips and hints gathered from the Cisco Technical Assistance Center (TAC). Most of these documents are available from the TAC FAX-on-demand service. To access FAX-on-demand and receive documents at your FAX machine, from the USA, call 888-50-CISCO (888-502-4726). From other areas, call 415-596-4408.

The following sections can be reached from the Technical Tips page:

Cisco Connection Online

Cisco Connection Online (CCO) is Cisco Systems' primary, real-time support channel. Maintenance customers and partners can self-register on CCO to obtain additional information and services.

Available 24 hours a day, 7 days a week, CCO provides a wealth of standard and value-added services to Cisco's customers and business partners. CCO services include product information, product documentation, software updates, release notes, technical tips, the Bug Navigator, configuration notes, brochures, descriptions of service offerings, and download access to public and authorized files.

CCO serves a wide variety of users through two interfaces that are updated and enhanced simultaneously: a character-based version and a multimedia version that resides on the World Wide Web (WWW). The character-based CCO supports Zmodem, Kermit, Xmodem, FTP, and Internet e-mail, and it is excellent for quick access to information over lower bandwidths. The WWW version of CCO provides richly formatted documents with photographs, figures, graphics, and video, as well as hyperlinks to related information.

You can access CCO in the following ways:

For a copy of CCO's Frequently Asked Questions (FAQ), contact cco-help@cisco.com. For additional information, contact cco-team@cisco.com.

Note If you are a network administrator and need personal technical assistance with a Cisco product that is under warranty or covered by a maintenance contract, contact Cisco's Technical Assistance Center (TAC) at 800 553-2447, 408 526-7209, or tac@cisco.com. To obtain general information about Cisco Systems, Cisco products, or upgrades, contact 800 553-6387, 408 526-7208, or cs-rep@cisco.com.

Documentation CD-ROM

Cisco documentation and additional literature are available in a CD-ROM package, which ships with your product. The Documentation CD-ROM, a member of the Cisco Connection Family, is updated monthly. Therefore, it might be more current than printed documentation. To order additional copies of the Documentation CD-ROM, contact your local sales representative or call customer service. The CD-ROM package is available as a single package or as an annual subscription. You can also access Cisco documentation on the World Wide Web at http://www.cisco.com, http://www-china.cisco.com, or http://www-europe.cisco.com.

If you are reading Cisco product documentation on the World Wide Web, you can submit comments electronically. Click Feedback in the toolbar and select Documentation. After you complete the form, click Submit to send it to Cisco. We appreciate your comments.





hometocprevnextglossaryfeedbacksearchhelp
Posted: Sun May 14 21:24:10 PDT 2000
Copyright 1989 - 2000©Cisco Systems Inc.