Novell IPX Commands

access-list-number	Number of the access list. This is a number from 900  to  999.
deny	Denies access if the conditions are matched.
permit	Permits access if the conditions are matched.
protocol	Name or number of an IPX protocol type. This is sometimes referred to as the packet type.
source-network	(Optional) Number of the network from which the packet is being sent. This is an eight-digit hexadecimal number that uniquely identifies a network cable segment. It can be a number in the range 1 to FFFFFFFE. A network number of 0 matches the local network. A network number of -1 matches all networks. You do not need to specify leading zeros in the network number; for example, for the network number 000000AA, you can enter  AA.
.source-node	(Optional) Node on source-network from which the packet is being sent. This is a 48-bit value represented by a dotted triplet of four-digit hexadecimal numbers (xxxx.xxxx.xxxx).
source-node-mask	(Optional) Mask to be applied to source-node. This is a 48-bit value represented as a dotted triplet of four-digit hexadecimal numbers (xxxx.xxxx.xxxx). Place ones in the bit positions you want to mask.
source-network-mask.	(Optional) Mask to be applied to source-network. This is an eight-digit hexadecimal mask. Place ones in the bit positions you want to mask. The mask must immediately be followed by a period, which must in turn immediately be followed by source-node-mask.
source-socket	(Optional) Socket name or number (hexadecimal) from which the packet is being sent.
destination.network	(Optional) Number of the network to which the packet is being sent. This is an eight-digit hexadecimal number that uniquely identifies a network cable segment. It can be a number in the range 1 to FFFFFFFE. A network number of 0 matches the local network. A network number of -1 matches all networks. You do not need to specify leading zeros in the network number. For example, for the network number 000000AA, you can enter AA.
.destination-node	(Optional) Node on destination-network to which the packet is being sent. This is a 48-bit value represented by a dotted triplet of four-digit hexadecimal numbers (xxxx.xxxx.xxxx).
destination-node-mask	(Optional) Mask to be applied to destination-node. This is a 48-bit value represented as a dotted triplet of four-digit hexadecimal numbers (xxxx.xxxx.xxxx). Place ones in the bit positions you want to mask.
destination-network-mask.	(Optional) Mask to be applied to destination-network. This is an eight-digit hexadecimal mask. Place ones in the bit positions you want to mask. The mask must immediately be followed by a period, which must in turn immediately be followed by destination-node-mask.
destination-socket	(Optional) Socket name or number (hexadecimal) to which the packet is being sent.
log	(Optional) Logs IPX access control list violations whenever a packet matches a particular access list entry. The information logged includes source address, destination address, source socket, destination socket, protocol type, and action taken (permit/deny).

network	Number of the network whose routing table entry you want to delete. This is an eight-digit hexadecimal number that uniquely identifies a network cable segment. It can be a number in the range 1 to FFFFFFFD. You do not need to specify leading zeros in the network number. For example, for the network number 000000AA, you can enter AA.
network-mask	(Optional) Specifies the portion of the network address that is common to all addresses in an NLSP route summary. When used with the network argument, it specifies the an NLSP route summary to clear. The high-order bits of network-mask must be contiguous Fs, while the low-order bits must be contiguous zeros (0). An arbitrary mix of Fs and 0s is not permitted.
default	Deletes the default route from the routing table.
*	Deletes all routes in the routing table.

protocol	Name or number of an IPX protocol type. This is sometimes referred to as the packet type. You can also use the word any to match all protocol types.
source-network	(Optional) Number of the network from which the packet is being sent. This is an eight-digit hexadecimal number that uniquely identifies a network cable segment. It can be a number in the range 1 to FFFFFFFE. A network number of 0 matches the local network. A network number of -1 matches all networks. You can also use the keyword any to match all networks. You do not need to specify leading zeros in the network number; for example, for the network number 000000AA, you can enter  AA.
.source-node	(Optional) Node on source-network from which the packet is being sent. This is a 48-bit value represented by a dotted triplet of four-digit hexadecimal numbers (xxxx.xxxx.xxxx).
source-node-mask	(Optional) Mask to be applied to source-node. This is a 48-bit value represented as a dotted triplet of four-digit hexadecimal numbers (xxxx.xxxx.xxxx). Place ones in the bit positions you want to mask.
source-network-mask.	(Optional) Mask to be applied to source-network. This is an eight-digit hexadecimal mask. Place ones in the bit positions you want to mask. The mask must immediately be followed by a period, which must in turn immediately be followed by source-node-mask.
source-socket	(Optional) Socket name or number (hexadecimal) from which the packet is being sent. You can also use the keyword all to match all sockets.
destination-network	(Optional) Number of the network to which the packet is being sent. This is an eight-digit hexadecimal number that uniquely identifies a network cable segment. It can be a number in the range 1 to FFFFFFFE. A network number of 0 matches the local network. A network number of -1 matches all networks. You can also use the keyword any to match all networks. You do not need to specify leading zeros in the network number. For example, for the network number 000000AA, you can enter AA.
.destination-node	(Optional) Node on destination-network to which the packet is being sent. This is a 48-bit value represented by a dotted triplet of four-digit hexadecimal numbers (xxxx.xxxx.xxxx).
destination-node-mask	(Optional) Mask to be applied to destination-node. This is a 48-bit value represented as a dotted triplet of four-digit hexadecimal numbers (xxxx.xxxx.xxxx). Place ones in the bit positions you want to mask.
destination-network-mask.	(Optional) Mask to be applied to destination-network. This is an eight-digit hexadecimal mask. Place ones in the bit positions you want to mask. The mask must immediately be followed by a period, which must in turn immediately be followed by destination-node-mask.
destination-socket	(Optional) Socket name or number (hexadecimal) to which the packet is being sent.
log	(Optional) Logs IPX access control list violations whenever a packet matches a particular access list entry. The information logged includes source address, destination address, source socket, destination socket, protocol type, and action taken (permit/deny).

network	Network number to summarize. An IPX network number is an eight-digit hexadecimal number that uniquely identifies a network cable segment. It can be a number in the range 1 to FFFFFFFE. A network number of 0 matches the local network. A network number of -1 matches all networks. You do not need to specify leading zeros in the network number. For example, for the network number 000000AA, you can enter  AA.
network-mask	Specifies the portion of the network address that is common to all addresses in the route summary, expressed as an 8-digit hexadecimal number. The high-order bits of network-mask must be contiguous 1s, while the low-order bits must be contiguous zeros (0). An arbitrary mix of 1s and 0s is not permitted.
ticks ticks	(Optional) Metric assigned to the route summary. The default is 1  tick.
area-count area-count	(Optional) Maximum number of NLSP areas to which the route summary can be redistributed. The default is 6 areas.

network	Network number. This is an eight-digit hexadecimal number that uniquely identifies a network cable segment. It can be a number in the range 1 to FFFFFFFE. A network number of 0 matches the local network. A network number of -1 matches all networks. You do not need to specify leading zeros in the network number. For example, for the network number 000000AA, you can enter  AA.
.node	(Optional) Node on network. This is a 48-bit value represented by a dotted triplet of four-digit hexadecimal numbers (xxxx.xxxx.xxxx).
network-mask.node-mask	(Optional) Mask to be applied to network and node. Place ones in the bit positions to be masked.
service-type	(Optional) Service type on which to filter. This is a hexadecimal number. A value of 0 means all services.
server-name	(Optional) Name of the server providing the specified service type. This can be any contiguous string of printable ASCII characters. Use double quotation marks ("  ") to enclose strings containing embedded spaces. You can use an asterisk (*) at the end of the name as a wildcard to match one or more trailing characters.

source-network	Number of the network from which the packet is being sent. This is an eight-digit hexadecimal number that uniquely identifies a network cable segment. It can be a number in the range 1 to FFFFFFFE. A network number of 0 matches the local network. A network number of -1 matches all networks. You do not need to specify leading zeros in the network number. For example, for the network number 000000AA, you can enter  AA.
.source-node	(Optional) Node on source-network from which the packet is being sent. This is a 48-bit value represented by a dotted triplet of four-digit hexadecimal numbers (xxxx.xxxx.xxxx).
source-node-mask	(Optional) Mask to be applied to source-node. This is a 48-bit value represented as a dotted triplet of four-digit hexadecimal numbers (xxxx.xxxx.xxxx). Place ones in the bit positions you want to mask.
destination-network	(Optional) Number of the network to which the packet is being sent. This is an eight-digit hexadecimal number that uniquely identifies a network cable segment. It can be a number in the range 1 to FFFFFFFE. A network number of 0 matches the local network. A network number of -1 matches all networks. You do not need to specify leading zeros in the network number. For example, for the network number 000000AA, you can enter  AA.
.destination-node	(Optional) Node on destination-network to which the packet is being sent. This is a 48-bit value represented by a dotted triplet of four-digit hexadecimal numbers (xxxx.xxxx.xxxx).
destination-node-mask	(Optional) Mask to be applied to destination-node. This is a 48-bit value represented as a dotted triplet of four-digit hexadecimal numbers (xxxx.xxxx.xxxx). Place ones in the bit positions you want to mask.

access-list-number	Standard IPX access list number in the range 800 to 899 or NLSP access list number in the range 1200 to 1299. The list explicitly specifies which networks are to be received and which are to be suppressed.
name	Name of the access list. Names cannot contain a space or quotation mark and must begin with an alphabetic character to prevent ambiguity with numbered access lists.
in	Applies the access list to incoming routing updates.
interface-name	(Optional) Interface on which the access list should be applied to incoming updates. If no interface is specified, the access list is applied to all incoming updates.

access-list-number	Standard IPX access list number in the range 800 to 899 or NLSP access list number in the range 1200 to 1299. The list explicitly specifies which networks are to be sent and which are to be suppressed in routing updates.
name	Name of the access list. Names cannot contain a space or quotation mark and must begin with an alphabetic character to prevent ambiguity with numbered access lists.
out	Applies the access list to outgoing routing updates.
interface-name	(Optional) Interface on which the access list should be applied to outgoing updates. If no interface is specified, the access list is applied to all outgoing updates.
routing-process	(Optional) Name of a particular routing process as follows: · eigrp autonomous-system-number · rip · nlsp [tag]

access-list-number	SAP access list number in the range 1000 to 1099. The list explicitly specifies which services are to be received and which are to be suppressed.
name	Name of the access list. Names cannot contain a space or quotation mark and must begin with an alphabetic character to prevent ambiguity with numbered access lists.
in	Applies the access list to incoming routing updates.
interface-name	(Optional) Interface on which the access list should be applied to incoming updates. If no interface is specified, the access list is applied to all incoming updates.

access-list-number	SAP access list number in the range 1000 to 1099. The list explicitly specifies which networks are to be sent and which are to be suppressed in routing updates.
name	Name of the access list. Names cannot contain a space or quotation mark and must begin with an alphabetic character to prevent ambiguity with numbered access lists.
out	Applies the access list to outgoing routing updates.
interface-name	(Optional) Interface on which the access list should be applied to outgoing updates. If no interface is specified, the access list is applied to all outgoing updates.
routing-process	(Optional) Name of a particular routing process as follows: · eigrp autonomous-system-number · nlsp [tag] · rip

access-list-number	Number of the access list. For standard access lists, access-list-number is a number from 800 to 899. For extended access lists, access-list-number is a number from 900 to 999.
name	Name of the access list. Names cannot contain a space or quotation mark and must begin with an alphabetic character to prevent ambiguity with numbered access lists.
in	(Optional) Filters inbound packets. All incoming packets defined with either standard or extended access lists are filtered by the entries in this access list.
out	(Optional) Filters outbound packets. All outgoing packets defined with either standard or extended access lists and forwarded through the interface are filtered by the entries in this access list. This is the default when you do not specify an input (in) or output (out) keyword in the command line.

standard	Specifies a standard IPX access list.
extended	Specifies an extended IPX access list.
sap	Specifies a SAP access list.
summary	Specifies area addresses that summarize routes using NLSP route aggregation filtering.
name	Name of the access list. Names cannot contain a space or quotation mark, and they must begin with an alphabetic character to prevent ambiguity with numbered access lists.

number	Network number. This is an eight-digit hexadecimal number that uniquely identifies a network cable segment. It can be a number in the range 1 to FFFFFFFD. You do not need to specify leading zeros in the network number. For example, for the network number 000000AA you can enter  AA.
mask	Network mask.

threshold

Maximum number of entries (source and destination address pairs) that the Cisco IOS software can accumulate.

count

Number of transit entries that will be stored in the IPX accounting database.

network

Number of the network via which to advertise the default route.

interval

Minimum time, in seconds, between successive queries of each Enhanced IGRP neighbor's backup server table. The default is 15  seconds.

as-number	Autonomous system number.
percent	Percentage of bandwidth that Enhanced IGRP may use.

delay

Delay, in milliseconds, between packets in a multiple-packet RIP update. The default delay is 55 ms. Novell recommends a delay of 55  ms.

delay

Delay, in milliseconds, between packets in a multiple-packet SAP update. The default delay is 55 ms. Novell recommends a delay of 55  ms.

delay

Delay, in milliseconds, between packets in a multiple-packet RIP update. The default delay is 55 ms. Novell recommends a delay of 55 ms.

delay

Delay, in milliseconds, between packets in a multiple-packet SAP update. The default delay is 55 ms. Novell recommends a delay of 55 ms.

ticks

Number of IBM clock ticks of delay to use. One clock tick is 1/18 of a second (approximately 55 ms).

network

Number of the network to shut down. This is an eight-digit hexadecimal number that uniquely identifies a network cable segment. It can be a number in the range 1 to FFFFFFFD. You do not need to specify leading zeros in the network number. For example, for the network number 000000AA, you can enter  AA.

milliseconds

(Optional) Time, in milliseconds, that the Cisco IOS software waits after receiving a GNS request from an IPX client before responding with a server name to that client. The default is zero, which indicates no delay.

autonomous-system-number	Enhanced IGRP autonomous system number. It can a number from 1 to 65535.
seconds	Interval between hello packets, in seconds. The default interval is 5 seconds, which is one-third of the default hold time.

network	Network on which the target IPX server resides. This is an eight-digit hexadecimal number that uniquely identifies a network cable segment. It can be a number in the range 1 to FFFFFFFD. A network number of -1 indicates all-nets flooding. You do not need to specify leading zeros in the network number. For example, for the network number 000000AA, you can enter AA.
.node	Node number of the target Novell server. This is a 48-bit value represented by a dotted triplet of four-digit hexadecimal numbers (xxxx.xxxx.xxxx). A node number of FFFF.FFFF.FFFF matches all servers.

access-list-number	Number of the access list. All outgoing packets defined with either standard or extended access lists are filtered by the entries in this access list. For standard access lists, access-list-number is a number from 800 to 899. For extended access lists, it is a number from 900 to 999.
name	Name of the access list. Names cannot contain a space or quotation mark and must begin with an alphabetic character to prevent ambiguity with numbered access lists.

autonomous-system-number	Enhanced IGRP autonomous system number. It can be a number from 1 to 65535.
seconds	Hold-down time, in seconds. The default hold time is 5  seconds.

autonomous-system-number	Enhanced IGRP autonomous system number. It can be a number from 1 to 65535.
seconds	Hold time, in seconds. The hold time is advertised in hello packets and indicates to neighbors the length of time they should consider the sender valid. The default hold time is 15  seconds, which is 3 times the hello interval.

access-list-number	Number of the access list. All incoming packets defined with either standard or extended access lists are filtered by the entries in this access list. For standard access lists, access-list-number is a number from 800 to 899. For extended access lists, it is a number from 900 to 999.
name	Name of the access list. Names cannot contain a space or quotation mark and must begin with an alphabetic character to prevent ambiguity with numbered access lists.

access-list-number	Number of the SAP access list. All incoming packets are filtered by the entries in this access list. The argument access-list-number is a number from 1000 to 1099.
name	Name of the access list. Names cannot contain a space or quotation mark, and they must begin with an alphabetic character to prevent ambiguity with numbered access lists.

network-number

Number of the internal network.

local-node	(Optional) Primary network number of the router. This is an IPX network number that is unique across the entire internetwork. On NetWare 3.x servers, the primary network number is called the internal network number. The device with the higher number is determined to be the link master. A value of 0 causes the Cisco IOS software to use the configured internal network number.
network-number	(Optional) IPX network number to be used for the link if this router is the one determined to be the link master. The number is an eight-digit hexadecimal number that uniquely identifies a network cable segment. It can be a number in the range 0 to FFFFFFFD. A value 0 is equivalent to specifying the keyword unnumbered. You do not need to specify leading zeros in the network number. For example, for the network number 000000AA, you can enter AA.
unnumbered	(Optional) Specifies that no IPX network number is defined for the link. This is equivalent to specifying a value of 0 for the network-number argument.
local-server-name	(Optional) Name of the local router. It can be up to 47 characters long, and can contain uppercase letters, digits, underscores (_), hyphens (-), and at signs (@). On NetWare 3.x servers, this is the router name. For our routers, this is the name of the router as configured via the hostname command; that is, the name that precedes the standard prompt, which is an angle bracket (>) for EXEC mode or a pound sign (#) for privileged EXEC mode.
retry-interval	(Optional) Retry interval, in seconds. This interval defines how often the software will retry the IPXWAN start-up negotiation if a start-up failure occurs. Retries will occur until the retry limit defined by the retry-limit argument is reached. It can be a value from 1 to 600. The default is 20 seconds.
retry-limit	(Optional) Maximum number of times the software retries the IPXWAN start-up negotiation before taking the action defined by the ipx ipxwan error command. It can be a value from 1 through 100. The default is 3.

reset	(Optional) Resets the link when negotiations fail. This is the default action.
resume	(Optional) When negotiations fail, IPXWAN ignores the failure, takes no special action, and resumes the start-up negotiation attempt.
shutdown	(Optional) Shuts down the link when negotiations fail.

microseconds

Delay, in microseconds.

rip	Enables the sending of a general RIP query when an interface comes up.
sap	Enables the sending of a general SAP query when an interface comes up.

hops	Maximum number of hops considered to be reachable by non-RIP routing protocols. Also, maximum number of routers that an IPX packet can traverse before being dropped. It can be a value from 16 to 254. The default is 16 hops.

paths

Maximum number of equal-cost paths which the Cisco  IOS software will use. It can be a number from 1 to 512. The default value is 1.

host	Indicates that the following argument is the name of a NetBIOS access filter previously defined with one or more netbios access-list host commands.
bytes	Indicates that the following argument is the name of a NetBIOS access filter previously defined with one or more netbios access-list bytes commands.
name	Name of a NetBIOS access list.

host	Indicates that the following argument is the name of a NetBIOS access filter previously defined with one or more netbios access-list host commands.
bytes	Indicates that the following argument is the name of a NetBIOS access filter previously defined with one or more netbios access-list bytes commands.
name	Name of a previously defined NetBIOS access list.

network	Network number. This is an eight-digit hexadecimal number that uniquely identifies a network cable segment. It can be a number in the range 1 to FFFFFFFD. You do not need to specify leading zeros in the network number. For example, for the network number 000000AA you can enter AA.
encapsulation encapsulation-type	(Optional) Type of encapsulation (framing). It can be one of the following values: · arpa (for Ethernet interfaces only)---Use Novell's Ethernet_II encapsulation. This encapsulation is recommended for networks that handle both TCP/IP and IPX traffic. · hdlc (for serial interfaces only)---Use HDLC encapsulation. · novell-ether (for Ethernet interfaces only)---Use Novell's "Ethernet_802.3" encapsulation. This encapsulation consists of a standard 802.3 Media Access Control (MAC) header followed directly by the IPX header with a checksum of FFFF. It is the default encapsulation used by all versions of NetWare up to and including Version 3.11. · novell-fddi (for FDDI interfaces only)---Use Novell's "FDDI_RAW" encapsulation. This encapsulation consists of a standard FDDI MAC header followed directly by the IPX header with a checksum of 0xFFFF. · sap (for Ethernet interfaces)---Use Novell's Ethernet_802.2 encapsulation.This encapsulation consists of a standard 802.3 MAC header followed by an 802.2 LLC header. This is the default encapsulation used by NetWare Version 3.12 and 4.0. --- Token Ring interfaces---This encapsulation consists of a standard 802.5 MAC header followed by an 802.2 LLC header. ---FDDI interfaces---This encapsulation consists of a standard FDDI MAC header followed by an 802.2 LLC header. · snap (for Ethernet interfaces)---Use Novell Ethernet_Snap encapsulation. This encapsulation consists of a standard 802.3 MAC header followed by an 802.2 SNAP LLC header. --- Token Ring and FDDI interfaces---This encapsulation consists of a standard 802.5 or FDDI MAC header followed by an 802.2 SNAP LLC header.
secondary	(Optional) Indicates an additional (secondary) network configured after the first (primary) network.

string

Authentication string configured for the source and destination stations that controls whether NHRP stations allow intercommunication. The string can be up to eight characters long.

seconds-positive	Time in seconds that NBMA addresses are advertised as valid in positive authoritative NHRP responses.
seconds-negative	(Optional) Time in seconds that NBMA addresses are advertised as valid in negative authoritative NHRP responses.

access-list-number

Standard or extended IPX access list number from 800 through 999.

ipx-address	IPX address of the destinations reachable through the NBMA network. This address is mapped to the NBMA address.
nbma-address	NBMA address that is directly reachable through the NBMA network. The address format varies depending on the medium you are using. For example, ATM has a network-service access point (NSAP) address, and SMDS has an E.164 address. This address is mapped to the IPX address.

pkt-count	Number of packets which can be transmitted in the range 1 to 65535.
every interval	Time (in seconds) in the range 10 to 65535. Default is 10 seconds.

number

Globally unique, 32-bit network identifier for a nonbroadcast, multiaccess (NBMA) network. The range is 1 to 4294967295.

nhs-address	Address of the Next Hop Server being specified.
net-address	(Optional) IPX address of a network served by the Next Hop Server.

type	Interface type whose primary IPX address is used when a Next Hop Server complies with a Responder Address option. Valid options are atm, serial, and tunnel.
number	Interface number whose primary IPX address is used when a Next Hop Server complies with a Responder Address option.

usage-count

Packet count in the range 1 to 65535.

tag	(Optional) Names the NLSP process. The tag can be any combination of printable characters.
seconds	Time, in seconds, between the transmission of CSNPs on multiaccess networks. This interval applies to the designated router only. The interval can be a number in the range 1 to 600. The default is 30 seconds.

tag	(Optional) Names the NLSP process. The tag can be any combination of printable characters.

tag	(Optional) Names the NLSP process. The tag can be any combination of printable characters.
seconds	Time, in seconds, between the transmission of hello packets on the interface. It can be a number in the range 1 to 1600. The default is 10 seconds for the designated router and 20  seconds for nondesignated routers.

tag	(Optional) Names the NLSP process. The tag can be any combination of printable characters.
multiplier	Value by which to multiply the hello interval. It can be a number in the range 3 to 1000. The default is 3.

tag	(Optional) Names the NLSP process. The tag can be any combination of printable characters.
metric-number	Metric value for the interface. It can be a number from 0 to 63.

tag	(Optional) Names the NLSP process. The tag can be any combination of printable characters.

tag	(Optional) Names the NLSP process. The tag can be any combination of printable characters.
priority-number	Election priority of the designated router for the specified interface. This can be a number in the range 0 to 127. This value is unitless. The default is 44.

tag	(Optional) Names the NLSP process. The tag can be any combination of printable characters.
seconds	LSP retransmission interval, in seconds. This can be a number in the range 1 to 30. The default is 5 seconds.

tag	(Optional) Names the NLSP process. The tag can be any combination of printable characters.
on	(Optional) Always generates and sends RIP periodic traffic.
off	(Optional) Never generates and sends RIP periodic traffic.
auto	(Optional) Sends RIP periodic traffic only if another RIP router in sending periodic RIP traffic. This is the default.

tag	(Optional) Names the NLSP process. The tag can be any combination of printable characters.
on	(Optional) Always generates and sends SAP periodic traffic.
off	(Optional) Never generates and sends SAP periodic traffic.
auto	(Optional) Sends SAP periodic traffic only if another SAP router in sending periodic SAP traffic. This is the default.

access-list-number	Number of the SAP access list. All outgoing GNS packets are filtered by the entries in this access list. The argument access-list-number is a number from 1000 to 1099.
name	Name of the access list. Names cannot contain a space or quotation mark, and they must begin with an alphabetic character to prevent ambiguity with numbered access lists.

delay

Delay, in milliseconds, between packets in a multiple-packet RIP update. The default delay is 55 ms. Novell recommends a delay of 55 ms.

delay

Delay, in milliseconds, between packets in a multiple-packet SAP update. The default delay is 55 ms. Novell recommends a delay of 55 ms.

access-list-number	Number of the SAP access list. All outgoing service advertisements are filtered by the entries in this access list. The argument access-list-number is a number from 1000 to  1099.
name	Name of the access list. Names cannot contain a space or quotation mark, and must begin with an alphabetic character to prevent ambiguity with numbered access lists.

cisco	Transmits Cisco pings.
novell	Transmits standard Novell pings.
diagnostic	Transmits diagnostic request/response for IPX pings.

bytes

Maximum packet size in bytes. The default is 432 bytes, which allows for 50 routes at 8 bytes each, plus 32 bytes of IPX network and RIP header information.

multiplier

Multiplier used to calculate the interval at which to age out RIP routing table entries. This can be any positive number. The value you specify is multiplied by the RIP update interval to determine the aging-out interval. The default is three times the RIP update interval.

ms	Delay time in milliseconds for RIP responses.

period	Number of minutes that a valid cache entry may be inactive before it is invalidated. Valid values are 0 through 65535. A value of zero disables this feature.
rate	(Optional) The maximum number of inactive entries that may be invalidated per minute. Valid values are 0 through 65535. A value of zero means no limit.

size	Maximum number of entries allowed in the IPX route cache.

period	Number of minutes since a valid cache entry was created before it may be invalidated. A value of zero disables this feature.
rate	(Optional) The maximum number of aged entries that may be invalidated per minute. A value of zero means no limit.

eigrp autonomous-system-number	Enables the Enhanced IGRP routing protocol. The argument autonomous-system-number is the Enhanced IGRP autonomous system number. It can be a number from 1 to 65535.
nlsp [tag]	Enables the NLSP routing protocol. The optional argument tag names the NLSP process to which you are assigning the NLSP protocol. If the router has only one process, defining a tag is optional. A maximum of three NLSP processes may be configured on the router at the same time. The tag can be any combination of printable characters.
rip	Enables the RIP routing protocol. It is on by default.

access-list-number	Number of the access list. All incoming packets defined with either standard or extended access lists are filtered by the entries in this access list. For standard access lists, access-list-number is a number from 800 to 899. For extended access lists, it is a number from 900 to 999.
name	Name of the access list. Names cannot contain a space or quotation mark, and must begin with an alphabetic character to prevent ambiguity with numbered access lists.

access-list-number	Number of the access list. All incoming service advertisements are filtered by the entries in this access list. The argument access-list-number is a number from 1000 to 1099.
name	Name of the access list. Names cannot contain a space or quotation mark, and must begin with an alphabetic character to prevent ambiguity with numbered access lists.

node

(Optional) Node number of the router. This is a 48-bit value represented by a dotted triplet of four-digit hexadecimal numbers (xxxx.xxxx.xxxx). It must not be a multicast address. If you omit node, the Cisco IOS software uses the hardware MAC address currently assigned to it as its node address. This is the MAC address of the first Ethernet, Token Ring, or FDDI interface card. If no satisfactory interfaces are present in the router (such as only serial interfaces), you must specify node.

service-type	SAP service-type number.
name	Name of the server that provides the service.
network.node	Network number and node address of the server. The argument network is an eight-digit hexadecimal number that uniquely identifies a network cable segment. It can be a number in the range 1 to FFFFFFFD. You do not need to specify leading zeros in the network number. For example, for the network number 000000AA you can enter AA. The argument node is the node number of the target Novell server. This is a 48-bit value represented by a dotted triplet of four-digit hexadecimal numbers (xxxx.xxxx.xxxx).
socket	Socket number for this service.
hop-count	Number of hops to the server.

eigrp autonomous-system-number	IPX Enhanced IGRP autonomous system number. It can be a number from 1 to 65535.
rsup-only	(Optional) Indicates that the system uses Enhanced IGRP on this interface to carry reliable SAP update information only. RIP routing updates are used, and Enhanced IGRP routing updates are ignored.

bytes

Maximum packet size in bytes. The default is 480 bytes, which allows for 7 servers (64 bytes each), plus 32 bytes of IPX network and SAP header information.

multiplier

Multiplier used to calculate the interval at which to age out SAP routing table entries. This can be any positive number. The value you specify is multiplied by the SAP update interval to determine the aging-out interval. The default is three times the SAP update interval.

number

Maximum length of the queue of pending SAP requests. By default, there is no limit to the number of pending SAP requests that the Cisco IOS software stores in this queue.

autonomous-system-number

Enhanced IGRP autonomous system number. It can be a number from 1 to 65535.

delay-in-seconds

The amount of time in seconds to wait before spoofing SPX keepalives after data transfer has stopped.

bits-per-second

Throughput, in bits per second.

delay

Delay, in milliseconds, between packets in a multiple-packet RIP update. The default delay is 55 ms. Novell recommends a delay of 55 ms.

delay

Delay, in milliseconds, between packets in a multiple-packet SAP update. The default delay is 55 ms. Novell recommends a delay of 55 ms.

rip	Adjusts the interval at which RIP updates are sent. The minimum interval is 10 seconds.
sap	Adjusts the interval at which SAP updates are sent. The minimum interval is 10 seconds.
value	The interval specified in seconds.
changes-only	Specifies the sending of a SAP update only when the link comes up, when the link is downed administratively, or when service information changes. This parameter is supported for SAP updates only.

seconds

Minimum interval, in seconds. It can be a number in the range 0 to 120. The default is 5 seconds.

bytes

MTU size, in bytes. It can be a number in the range 512 to 4096. The default is 512 bytes.

seconds

Refresh interval, in seconds. It can be a value in the range 1 to 50000 seconds. The default is 7200 seconds (2 hours).

hours	(Optional) If specified, the lifetime of the LSP is set in hours. If not specified, the lifetime is set in seconds.
value	Lifetime of LSP in hours or seconds. It can be a number in the range 1 to 32767. The default is 7500 seconds.

host	Indicates that the following argument is the name of a NetBIOS access filter previously defined with one or more netbios access-list host commands.
bytes	Indicates that the following argument is the name of a NetBIOS access filter previously defined with one or more netbios access-list bytes commands.
name	Name of the access list being defined. The name can be an alphanumeric string.
deny	Denies access if the conditions are matched.
permit	Permits access if the conditions are matched.
string	Character string that identifies one or more NetBIOS host names. It can be up to 14 characters long. The argument string can include the following wildcard characters: · *---Match one or more characters. You can use this wildcard character only at the end of a string. · ?---Match any single character.
offset	Decimal number that indicates the number of bytes into the packet at which the byte comparison should begin. An offset of 0 indicates the beginning of the NetBIOS packet header, which is at the end of the IPX header.
byte-pattern	Hexadecimal pattern that represents the byte pattern to match. It can be up to 16 bytes (32 digits) long and must be an even number of digits. The argument byte-pattern can include the double asterisk (**) wildcard character to match any digits for that byte.

network-number	IPX network number.
all	Enables the routing protocol for all IPX networks configured on the router.

protocol	Name or number of an IPX protocol type. This is sometimes referred to as the packet type. You can also use the word any to match all protocol types.
source-network	(Optional) Number of the network from which the packet is being sent. This is an eight-digit hexadecimal number that uniquely identifies a network cable segment. It can be a number in the range 1 to FFFFFFFE. A network number of 0 matches the local network. A network number of -1 matches all networks. You can also use the word any to match all networks. You do not need to specify leading zeros in the network number; for example, for the network number 000000AA, you can enter  AA.
.source-node	(Optional) Node on source-network from which the packet is being sent. This is a 48-bit value represented by a dotted triplet of four-digit hexadecimal numbers (xxxx.xxxx.xxxx).
source-node-mask	(Optional) Mask to be applied to source-node. This is a 48-bit value represented as a dotted triplet of four-digit hexadecimal numbers (xxxx.xxxx.xxxx). Place ones in the bit positions you want to mask.
source-network-mask.	(Optional) Mask to be applied to source-network. This is an eight-digit hexadecimal mask. Place ones in the bit positions you want to mask. The mask must immediately be followed by a period, which must in turn immediately be followed by source-node-mask.
source-socket	Socket name or number (hexadecimal) from which the packet is being sent. You can also use the word all to match all sockets.
destination-network	(Optional) Number of the network to which the packet is being sent. This is an eight-digit hexadecimal number that uniquely identifies a network cable segment. It can be a number in the range 1 to FFFFFFFE. A network number of 0 matches the local network. A network number of -1 matches all networks. You can also use the word any to match all networks. You do not need to specify leading zeros in the network number. For example, for the network number 000000AA, you can enter AA.
.destination-node	(Optional) Node on destination-network to which the packet is being sent. This is a 48-bit value represented by a dotted triplet of four-digit hexadecimal numbers (xxxx.xxxx.xxxx).
destination-node-mask	(Optional) Mask to be applied to destination-node. This is a 48-bit value represented as a dotted triplet of four-digit hexadecimal numbers (xxxx.xxxx.xxxx). Place ones in the bit positions you want to mask.
destination-network-mask.	(Optional) Mask to be applied to destination-network. This is an eight-digit hexadecimal mask. Place ones in the bit positions you want to mask. The mask must immediately be followed by a period, which must in turn immediately be followed by destination-node-mask.
destination-socket	(Optional) Socket name or number (hexadecimal) to which the packet is being sent.
log	(Optional) Logs IPX access control list violations whenever a packet matches a particular access list entry. The information logged includes source address, destination address, source socket, destination socket, protocol type, and action taken (permit/deny).

network	Network number to summarize. An IPX network number is an eight-digit hexadecimal number that uniquely identifies a network cable segment. It can be a number in the range 1 to FFFFFFFE. A network number of 0 matches the local network. A network number of -1 matches all networks. You do not need to specify leading zeros in the network number. For example, for the network number 000000AA, you can enter AA.
network-mask	Specifies the portion of the network address that is common to all addresses in the route summary, expressed as an eight-digit hexadecimal number. The high-order bits of network-mask must be contiguous 1s, while the low-order bits must be contiguous zeros (0). An arbitrary mix of 1s and 0s is not permitted.
ticks ticks	(Optional) Metric assigned to the route summary. The default is 1  tick.
area-count area-count	(Optional) Maximum number of NLSP areas to which the route summary can be redistributed. The default is 6 areas.

network	Network number. This is an eight-digit hexadecimal number that uniquely identifies a network cable segment. It can be a number in the range 1 to FFFFFFFE. A network number of 0 matches the local network. A network number of -1 matches all networks. You do not need to specify leading zeros in the network number. For example, for the network number 000000AA, you can enter AA.
.node	(Optional) Node on network. This is a 48-bit value represented by a dotted triplet of four-digit hexadecimal numbers (xxxx.xxxx.xxxx).
network-mask.node-mask	(Optional) Mask to be applied to network and node. Place ones in the bit positions to be masked.
service-type	(Optional) Service type on which to filter. This is a hexadecimal number. A value of 0 means all services.
server-name	(Optional) Name of the server providing the specified service type. This can be any contiguous string of printable ASCII characters. Use double quotation marks ("  ") to enclose strings containing embedded spaces. You can use an asterisk (*) at the end of the name as a wildcard to match one or more trailing characters.

source-network	Number of the network from which the packet is being sent. This is an eight-digit hexadecimal number that uniquely identifies a network cable segment. It can be a number in the range 1 to FFFFFFFE. A network number of 0 matches the local network. A network number of -1 matches all networks. You do not need to specify leading zeros in the network number. For example, for the network number 000000AA, you can enter AA.
.source-node	(Optional) Node on source-network from which the packet is being sent. This is a 48-bit value represented by a dotted triplet of four-digit hexadecimal numbers (xxxx.xxxx.xxxx).
source-node-mask	(Optional) Mask to be applied to source-node. This is a 48-bit value represented as a dotted triplet of four-digit hexadecimal numbers (xxxx.xxxx.xxxx). Place ones in the bit positions you want to mask.
destination-network	(Optional) Number of the network to which the packet is being sent. This is an eight-digit hexadecimal number that uniquely identifies a network cable segment. It can be a number in the range 1 to FFFFFFFE. A network number of 0 matches the local network. A network number of -1 matches all networks. You do not need to specify leading zeros in the network number. For example, for the network number 000000AA, you can enter AA.
.destination-node	(Optional) Node on destination-network to which the packet is being sent. This is a 48-bit value represented by a dotted triplet of four-digit hexadecimal numbers (xxxx.xxxx.xxxx).
destination-node-mask	(Optional) Mask to be applied to destination-node. This is a 48-bit value represented as a dotted triplet of four-digit hexadecimal numbers (xxxx.xxxx.xxxx). Place ones in the bit positions you want to mask.

ipx	(Optional) Specifies the IPX protocol.
network.node	(Optional) Address of the system to ping.

ipx	Specifies the IPX protocol.
host	Host name of system to ping.
address	Address of system to ping.

seconds

Minimum amount of time between partial route calculations, in seconds. It can be a number in the range 1 to 120. The default is 5 seconds.

For Enhanced IGRP or RIP environments, use the following command to redistribute from one routing domain into another, and vice versa:

connected	Specifies connected routes.
eigrp autonomous-system-number	Specifies the Enhanced IGRP protocol and the Enhanced IGRP autonomous system number. It can be a number from 1 to 65535.
floating-static	Specifies a floating static route. This is a static route that can be overridden by a dynamically learned route.
nlsp [tag]	Specifies the NLSP protocol and, optionally, names the NLSP process (tag). The tag can be any combination of printable characters.
rip	Specifies the RIP protocol. You can configure only one RIP process on the router. Thus, you cannot redistribute RIP into RIP.
static	Specifies static routes.
access-list access-list-number	Specifies an NLSP route summary access list. The access-list-number is a number from 1200 to 1299.
access-list name	Name of the access list. Names cannot contain a space or quotation mark, and must begin with an alphabetic character to prevent ambiguity with numbered access lists.

access-list-number	(Optional) Number of the IPX access list to display. This is a number from 800 to 899, 900 to 999, 1000 to 1099, or 1200 to 1299.
name	(Optional) Name of the IPX access list to display.

checkpoint

(Optional) Displays entries in the checkpoint database.

servers	(Optional) Displays the server list advertised by each neighbor. This is displayed only if the ipx sap incremental command is enabled on the interface on which the neighbor resides.
autonomous-system-number	(Optional) Autonomous system number. It can be a number from 1 to 65535.
interface	(Optional) Interface type and number.
regexp name	(Optional) Displays the IPX servers whose names match the regular expression.

network-number

(Optional) IPX network number whose topology table entry to display.

type	(Optional) Interface type. It can be one of the following types: asynchronous, dialer, Ethernet (IEEE 802.3), FDDI, loopback, null, serial, Token Ring, or tunnel.
number	(Optional) Interface number.

dynamic	(Optional) Displays only the dynamic (learned) IPX-to-NBMA address cache entries.
static	(Optional) Displays only the static IPX-to-NBMA address entries in the cache (configured through the ipx nhrp map command).
type	(Optional) Interface type about which to display the NHRP cache. Valid options are atm, serial, and tunnel.
number	(Optional) Interface number about which to display the NHRP cache.

tag	(Optional) Names the NLSP process. The tag can be any combination of printable characters.
lspid	(Optional) Link-state protocol ID (LSPID). You must specify this in the format xxxx.xxxx.xxxx.yy-zz. The components of this argument have the following meaning: · xxxx.xxxx.xxxx is the system identifier. · yy is the pseudo identifier. · zz is the LSP number.
detail	(Optional) Displays the contents of the LSP database entries. If you omit this keyword, only a summary display is shown.

tag	(Optional) Names the NLSP process. The tag value can be any combination of printable characters.
interface	(Optional) Interface type and number.
detail	(Optional) Displays detailed information about the neighbor. If you omit this keyword, only a summary display is shown.

tag	(Optional) Names the NLSP process. The tag can be any combination of printable characters.

network	(Optional) Number of the network whose routing table entry you want to display. This is an eight-digit hexadecimal number that uniquely identifies a network cable segment. It can be a number in the range 1 to FFFFFFFD. You do not need to specify leading zeros in the network number. For example, for the network number 000000AA, you can enter AA.
default	(Optional) Displays the default route. This is equivalent to specifying a value of FFFFFFFE for the argument network.
detailed	(Optional) Displays detailed route information.

seconds

Minimum amount of time between SPF calculations, in seconds. It can be a number in the range 1 to 120. The default is 5 seconds.

protocol	(Optional) Name or number of an IPX protocol type. This is sometimes referred to as the packet type. You can also use the keyword ipx to specify the protocol type.
destination	(Optional) Destination address or host name on the command line. The default parameters for the appropriate protocol are assumed and the tracing action begins.