|
|
The Voice over IP feature enables the Cisco 2600 and Cisco 3600 series of modular routers to carry voice traffic simultaneously with data traffic over an IP network. Voice over IP (VoIP) is primarily a software feature, supporting both voice and fax calls. Support for the ISDN BRI signaling type allows a Cisco 2600 or Cisco 3600 series router to provide voice access connectivity to either an ISDN telephone network or a digital interface on a PBX/key communications system. The voice or data also crosses an IP network to which the router connects. This allows branch offices and enterprises to route incoming public switched telephone network (PSTN) ISDN BRI calls over an IP network or send outgoing digital fax and voice calls via an IP network.
Figure 1 shows a home-office user dialing directly into a local router via the PSTN, and reaching headquarters through an IP network, saving the cost of a long-distance call. In another example, Figure 1 shows how an extension at headquarters makes a fax or voice call to a branch office in a different area code using a corporate IP network only.
ications for ISDN BRI Voice over IP
To use this feature on a Cisco 2600 or Cisco 3600 series router, you must install a voice network module (VNM). A VNM can hold either one or two voice interface cards (VICs), each of which is specific to a particular signaling type. In the case of BRI VICs (VIC-2BRI-S/T-TE), which have two ports, a two-slot VNM holds a single BRI VIC to provide a total of four digital B channels for voice calls. This document describes how to configure ISDN Basic Rate Interface (BRI) VICs for VoIP.
For complete VoIP configuration instructions, see Cisco IOS Release 12.0 Voice, Video, and Home Applications Configuration Guide. For a description of the commands used to configure VoIP, see the "Voice-Related Commands" chapter in the Voice, Video, and Home Applications Command Reference.
ISDN BRI VoIP offers direct ISDN network connectivity as well as connectivity to the digital interfaces of PBX and Key communications systems. Prior to the introduction of this feature, VoIP was available only for foreign exchange station (FXS) connection to a POTS telephone or other TE, FXO for connection to a POTS PBX or Key system, or ear and mouth (E&M) for two-wire and four-wire telephone and trunk interfaces---typically used to connect remote calls from an IP network to a PBX.
ISDN BRI VoIP provides the following toll-saving benefits for enterprises and branch offices:
This feature is supported on the following platforms:
This feature requires Cisco IOS Release 12.0(2)XD, 12.0(2)XD1, or 12.0(3)T.
Before you can configure your Cisco 2600 or Cisco 3600 series router for VoIP on a BRI interface, you must:
None.
BRI---Basic Rate Interface. ISDN interface composed of two B channels and one D channel for circuit-switched communication of voice, video, and data.
dial peer---An addressable call endpoint. In Voice over IP (VoIP), there are two types of dial peers: POTS and VoIP.
DNS---Domain name system used in address translation to convert H.323 IDs, URLs, or e-mail IDs to IP addresses. DNS is also used to assist in the location of remote gatekeepers and to reverse-map raw IP addresses to host names of administrative domains.
DNIS---Dialed number identification service (the called number). Feature of trunk lines where the called number is identified; this called number information is used to route the call to the appropriate service.
E.164---International Telecommunication Union (ITU-T) recommendation for international telecommunication numbering. This recommendation provides the number structure and functionality for the 3 categories of numbers used for international public telecommunication: geographic areas, global services, and networks.
E&M---E&M (recEive and transMit or Ear and Mouth). E&M is a trunking arrangement generally used for two-way switch-to-switch or switch-to-network connections. Cisco's E&M interface is an RJ-48 connector that allows connections to PBX trunk lines (tie lines).
FXO---Foreign Exchange Office. An FXO interface connects to the PSTN's central office and is the interface offered on a standard telephone. Cisco's FXO interface is an RJ-11 connector that allows an analog connection to be directed at the PSTN's central office. This interface is of value for off-premise extension applications.
FXS---Foreign Exchange Station. An FXS interface connects directly to a standard telephone and supplies ring, voltage, and dial tone. Cisco's FXS interface is an RJ-11 connector that allows connections to basic telephone service equipment, keysets, and PBXs.
gateway---An H.323 endpoint on the LAN that provides real-time, two-way communications between H.323 terminals on the LAN and other ITU-T terminals in the WAN, or to another H.323 gateway. A gateway allows H.323 terminals to communicate with non-H.323 terminals by converting protocols. A gateway is the point at which a circuit-switched call is encoded and repackaged into IP packets.
H.323---An ITU-T standard that describes packet-based video, audio, and data conferencing. H.323 is an umbrella standard that describes the architecture of the conferencing system, and refers to a set of other standards (H.245, H.225.0, and Q.931) to describe its actual protocol.
ISDN---Integrated Services Digital Network. Communication protocol, offered by telephone companies, that permits telephone networks to carry data, voice, and other source traffic.
NM---Network module.
POTS---Plain Old Telephone Service. Basic telephone service supplying standard single-line telephones, telephone lines, and access to the public switched telephone network.
PSTN---Public switched telephone network, also refers to the local telephone company.
QoS---Quality of service, which refers to the measure of service quality provided to the user.
Technology prefix---Discriminators used to distinguish between gateways having specific capabilities within a given zone. In the exchange between the gateway and the gatekeeper, the technology prefix is used to select a gateway after the zone has been selected. Technology prefixes can be used to tell the gatekeeper that a certain technology is associated with a particular call (for example, 15# could mean a fax transmission), or it can be used like an area code for more generic routing. No standard defines what the numbers in a technology prefix mean; by convention, technology prefixes are designated by a pound (#) symbol as the last character.
SPID---Service profile identifier. Number that some service providers use to define the services to which an ISDN device subscribes. The ISDN device uses the SPID when accessing the switch that initializes the connection to a service provider.
VIC---Voice interface card.
VNM---Voice network module.
VoIP---Voice over IP. The ability to carry normal telephone-style voice over an IP-based internet with POTS-like functionality, reliability, and voice quality. VoIP is a blanket term that generally refers to Cisco's standards based (for example, H.323) approach to IP voice traffic.
WIC---Wide-area network (WAN) interface card.
To set up the BRI interface characteristics, set the global parameters and then configure each interface separately. Next, configure dial peers for VoIP.
To configure BRI interfaces, perform the following configuration tasks:
| Step | Command | Purpose | ||
|---|---|---|---|---|
| Router#configure terminal | Enter global configuration mode. | ||
| Router(config)#isdn switch-type switch-type | Configure the global ISDN switch type to match the service provider switch type. For a list of keywords, see Table 1. | ||
| Router(config)#interface bri slot/port | Enter interface configuration mode to configure parameters for the specified interface. slot is the location of the voice network module in the router. port is the location of the BRI VIC in the voice network module. Valid values are 0 or 1. | ||
| Router(config-if)#no ip address | Specify that there is no IP address for this interface. For information about IP addressing, see the IOS software document, Network Protocols Configuration Guide, Part 1. | ||
| Router(config-if)#no ip-directed broadcast | Disable the translation of directed broadcast to physical broadcasts. | ||
| Router(config-if)#isdn switch-type switch-type | (Optional) Configure the interface ISDN switch type to match the service provider switch type. The interface ISDN switch type overrides the global ISDN switch type on the interface. For a list of keywords, refer to Table 1. | ||
| Router(config-if)#isdn spid1 spid-number [ldn] | Specify a SPID and local directory number for the B1 channel. Currently, only the DMS-100 and NI-1 switch types require SPIDs. Although the Lucent 5ESS switch type might support a SPID, we recommend that you set up that ISDN service without SPIDs. | ||
| Router(config-if)#isdn spid2 spid-number [ldn] | Specify a SPID and local directory number for the B2 channel. | ||
| Router(config-if)#isdn twait-disable | (Optional) Use this command when the ISDN switch type is basic-ni1. Delay a National ISDN BRI switch a random time before activating the Layer 2 interface when the switch starts up. | ||
| Router(config-if)#isdn incoming-voice modem | Configure the port for incoming voice calls. |
When you have finished configuring one interface, you can repeat Steps 3 through 10 above.
| Country | ISDN Switch Type | Description |
|---|---|---|
Australia | basic-ts013 | Australian TS013 switches |
Europe | basic-1tr6 | German 1TR6 ISDN switches |
| basic-nwnet3 | Norwegian NET3 ISDN switches (phase 1) |
| basic-net3 | NET3 ISDN switches (UK and others) |
| vn2 | French VN2 ISDN switches |
| vn3 | French VN3 ISDN switches |
Japan | ntt | Japanese NTT ISDN switches |
New Zealand | basic-nznet3 | New Zealand NET3 switches |
North America | basic-5ess | Lucent Technologies basic rate switches |
| basic-dms100 | NT DMS-100 basic rate switches |
| basic-ni1 | National ISDN-1 switches |
To verify the ISDN BRI interface configuration, follow the steps below.
Step 1 The show running-config command in EXEC mode shows the current configuration running on the terminal. The example below shows some of the command output that is relevant to BRI configuration tasks.
Router#show running-config Building configuration... Current configuration: ! version 12.0 no service udp-small-servers service tcp-small-servers ! hostname Router ! enable secret 5 $1$c8xi$tObplXsIS.jDeo43yZgq50 enable password xxx ! username xxxx password x 11x5xx07 no ip domain-lookup ip host Labhost 172.17.12.1 ip host Labhost2 172.17.12.2 ip name-server 171.70.169.21 ! ... interface BRI1/0 no ip address no ip directed-broadcast isdn switch-type basic-ni1 isdn twait-disable isdn spid1 140855542790101 5554279 isdn spid2 140855542800101 5554280 isdn incoming-voice modem!interface BRI1/1 no ip address no ip directed-broadcast isdn switch-type basic-ni1 isdn twait-disable isdn spid1 140855542290101 5554229 isdn spid2 140855542330101 5554233 isdn incoming-voice modem!interface BRI2/0 no ip address no ip directed-broadcast isdn switch-type basic-ni1 isdn twait-disable isdn spid1 140855542110101 5554211 isdn spid2 140855542120101 5554212 isdn incoming-voice modem!interface BRI2/1 no ip address no ip directed-broadcast isdn switch-type basic-ni1 isdn twait-disable isdn spid1 140855546880101 5554688 isdn spid2 140855546890101 5554689 isdn incoming-voice modem...
Step 2 The show interfaces bri command displays information about the physical attributes of the ISDN BRI B and D channels. The term "spoofing" means that the interface is presenting itself to the IOS software as operational.
Router#show interfaces bri
BRI1/0 is up, line protocol is up (spoofing)
Hardware is Voice TE BRI
MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec,
reliablility 255/255, txload 1/255, rxload 1/255
Encapsulation VOICE, loopback not set
Last input 00:00:08, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0 (size/max/drops); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/0/256 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
109063 packets input, 508010 bytes, 0 no buffer
Received 425 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
11115 packets output, 1503160 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 output buffer failures, 0 output buffers swapped out
1 carrier transitions
BRI1/0:1 is down, line protocol is down
Hardware is Voice TE BRI
MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec,
reliablility 255/255, txload 1/255, rxload 1/255
Encapsulation VOICE, loopback not set, keepalive set (10 sec)
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0 (size/max/drops); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/0/256 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
11115 packets output, 1503160 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
BRI1/0:2 is down, line protocol is down
Hardware is Voice TE BRI
MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec,
reliablility 255/255, txload 1/255, rxload 1/255
Encapsulation VOICE, loopback not set, keepalive set (10 sec)
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0 (size/max/drops); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/0/256 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
11115 packets output, 1503160 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions buffer failures, 0 output buffers swapped out
To configure VoIP dial peers, repeat the following steps for each dial peer:
| Step | Command | Purpose | ||
|---|---|---|---|---|
| Router(config-if)#dial-peer voice tag-number {voip | pots}
| Enter dial-peer configuration mode to configure parameters for the specified dial peer. The dial peer is identified by the tag number. Valid entries for tag-number are from 1 to 10000. voip indicates that this is a VoIP peer using voice encapsulation on the PSTN and pointing to a specific IP address. pots indicates that this is a POTS peer using Voice over IP encapsulation on the IP backbone and pointing to a specific voice port on a voice network device. | ||
| Router(config-if)#direct-inward-dial | (Optional) POTs peers only. Configures the router to identify the destination dial peer by deriving a Direct Inward Dial (DID) called-number from the ISDN setup message. When a call arrives for this peer, the router forwards the call directly to the configured destination, instead of presenting dial tone and collecting dialed digits. Note Most configurations associate only one POTS dial peer for each port. However, if DID configuration is used and more than one dial peer points to the same port, DID should be specified for all of the associated dial peers. | ||
| Router(config-if)#destination-pattern [tech-prefix#]string[t] | Specify the telephone number (E.164 or otherwise) associated with this dial peer. Use the tech-prefix argument to define a technology prefix. Note Technology prefixes are required for some Registration, Admission, and Status (RAS) gateways. For more information, see the Cisco IOS Release 12.0(2)XD configuration note, Using Cisco 3600 and Cisco 2600 Series Routers as H.323 VoIP Gateways. | ||
| Router(config-if)#port slot-number/subunit-number/port | POTS peers only. Specify the voice port through which incoming VoIP calls will be received. The three-part number indicates the chassis slot, voice network module slot, and the VIC port, in that order. | ||
| Router(config-if)#session target {ipv4:destination-address | dns:[$s$. | $d$. | $e$. | $u$.] host-name | loopback:rtp | loopback:compressed | loopback:uncompressed | ras}
| VoIP peers only. Indicate a network-specific address for a dial peer. ipv4:destination-address specifies the IP address of the dial peer. dns:host-name indicates that the domain name server (DNS) will be used to resolve the name of the IP address. Valid entries are characters representing the name of the host device. One of the following optional wildcards can further define the session target:
The following three loopback parameters are used only for loopback testing: loopback:rtp indicates that all voice data will be looped back to the originating source (applicable to VoIP peers). loopback:compressed indicates that all voice data will be looped back in compressed mode to the originating source (applicable to POTS peers). loopback:uncompressed indicates that all voice data will be looped-back in uncompressed mode to the originating source (applicable to POTS peers). ras indicates that the Registration, Admission and Status (RAS) signaling function protocol is in use and a gatekeeper will be consulted to translate the E.164 address to an IP address. |
The show dial-peer voice command displays information about the dial-peer configuration.
The following example shows output from the show dial-peer voice command for a VoIP dial peer using a BRI VIC:
Router#show dial-peer voice
VoiceOverIpPeer13
tag = 13, destination-pattern = \Q9.......',
answer-address = \Q', preference=0,
group = 13, Admin state is up, Operation state is up,
incoming called-number = \Q', connections/maximum = 0/unlimited,
application associated:
type = voip, session-target = \Qipv4:12.0.0.2',
technology prefix:
ip precedence = 0, UDP checksum = disabled,
session-protocol = cisco, req-qos = best-effort,
acc-qos = best-effort,
fax-rate = voice, codec = g729r8,
Expect factor = 10, Icpif = 30,
VAD = enabled, Poor QOV Trap = disabled,
Connect Time = 0, Charged Units = 0,
Successful Calls = 0, Failed Calls = 0,
Accepted Calls = 0, Refused Calls = 0,
Last Disconnect Cause is "",
Last Disconnect Text is "",
Last Setup Time = 0.
VoiceOverIpPeer12
tag = 12, destination-pattern = \Q7....',
answer-address = \Q', preference=0,
group = 12, Admin state is up, Operation state is up,
incoming called-number = \Q', connections/maximum = 0/unlimited,
application associated:
type = voip, session-target = \Qipv4:12.0.0.2',
technology prefix:
ip precedence = 0, UDP checksum = disabled,
session-protocol = cisco, req-qos = best-effort,
acc-qos = best-effort,
fax-rate = voice, codec = g729r8,
Expect factor = 10, Icpif = 30,
VAD = enabled, Poor QOV Trap = disabled,
Connect Time = 4123, Charged Units = 0,
Successful Calls = 2, Failed Calls = 0,
Accepted Calls = 2, Refused Calls = 0,
Last Disconnect Cause is "10 ",
Last Disconnect Text is "normal call clearing.",
Last Setup Time = 989287.
The configuration examples included in this section correspond to the topology shown in Figure 2. The routers each include a BRI VIC and a two-slot voice network module, along with other voice interface cards and modules that are included for the sake of completeness. Router A is connected to a PBX through the BRI VIC and connected to Router B by a serial Ethernet interface. Router B includes a BRI VIC for connection to the PSTN, in order to process voice calls from off-premises terminal equipment.
For more information about IP configuration, see the Cisco IOS Release 12.0 Network Protocols Configuration Guide, Part 1. For more information about VoIP configuration, see Cisco IOS Release 12.0 Voice, Video, and Home Applications Configuration Guide.
The following example illustrates the configuration of a Cisco 3640 router for connection to a BRI VIC accessing a PBX:
vicbri_3640_s1#sh run Building configuration... Current configuration: ! version 12.0 service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname vicbri_3640_s1 ! logging buffered 200000 debugging ! ip subnet-zero ip host keyer 223.255.254.254 ! isdn switch-type basic-ni ! !
The following commands configure the ports on VICs. The last four specified ports are for FXO and E&M VICs:
voice-port 1/0/0 ! voice-port 1/0/1 ! voice-port 2/0/0 ! voice-port 2/0/1 ! voice-port 3/0/0 operation 4-wire type 2 ! voice-port 3/0/1 operation 4-wire type 2 ! voice-port 3/1/0 input gain 10 connection plar 39019 ! voice-port 3/1/1 input gain 10 connection plar 39020
The following commands configure dial peers to specify where incoming VoIP calls should be directed. In the first example, call received with a starting digit of 5 are sent to the PBX via the BRI VIC:
dial-peer voice 10 pots destination-pattern 5..... port 1/1/0 !
This command sets up a local BRI connection:
dial-peer voice 11 pots destination-pattern 66002 port 1/0/0 !
In this example, calls with a starting digit of 9 are PSTN calls that are routed over IP:
dial-peer voice 13 voip destination-pattern 9....... session target ipv4:12.0.0.2 !
This command sets up an FXS connection over IP to the other router:
dial-peer voice 12 voip (calls to other router with FXS - go over IP) destination-pattern 7.... session target ipv4:12.0.0.2 !
The following global configuration commands define how to expand an extension number into a particular destination pattern.
num-exp 8 9529399 num-exp 1 550950 num-exp 2 76002
The following commands configure the Ethernet and serial interfaces:
interface Ethernet0/0 ip address 1.14.122.10 255.255.0.0 ip helper-address 223.255.254.254 no ip directed-broadcast ! interface Serial0/0 ip address 3.0.0.2 255.0.0.0 no ip directed-broadcast no ip mroute-cache no keepalive no fair-queue ! interface Ethernet0/1 ip address 11.0.0.1 255.0.0.0 no ip directed-broadcast ! interface Serial0/1 ip address 14.0.0.1 255.0.0.0 no ip directed-broadcast no keepalive shutdown no fair-queue clockrate 2000000
The following commands configure the BRI interfaces:
interface BRI1/0 no ip address no ip directed-broadcast isdn switch-type basic-ni1 isdn twait-disable isdn spid1 14085552121010 5552121 isdn spid2 14085552122010 5552122 isdn incoming-voice modem ! interface BRI1/1 no ip address no ip directed-broadcast isdn switch-type basic-ni1 isdn twait-disable isdn spid1 14085556362010 5556362 isdn spid2 14085556364010 5556364 isdn incoming-voice modem ! interface BRI2/0 no ip address no ip directed-broadcast isdn switch-type basic-ni1 isdn twait-disable isdn spid1 14085555711010 5555711 isdn spid2 14085555712010 5555712 isdn incoming-voice modem ! interface BRI2/1 no ip address no ip directed-broadcast isdn switch-type basic-ni1 isdn twait-disable isdn spid1 14085555162010 5555162 isdn spid2 14085555163010 5555163 isdn incoming-voice modem ! ip default-gateway 1.14.0.1 ip classless ip route 2.0.0.0 255.0.0.0 Ethernet0/1 ip route 2.0.0.0 255.0.0.0 Serial0/1 ip route 223.255.254.254 255.255.255.255 Ethernet0/0 ! ! ! line con 0 exec-timeout 0 0 transport input none line aux 0 line vty 0 4 login ! end vicbri_3640_s1#
The following example illustrates the configuration of a Cisco 2600 series router for connection to a BRI VIC accessing an ISDN telephone network:
vicbri_2600_s2#sh run Building configuration... Current configuration: ! version 12.0 service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname vicbri_2600_s2 ! logging buffered 200000 debugging ! ip subnet-zero ! isdn switch-type basic-ni ! !
The following commands configure the ports on VICs:
voice-port 1/0/0 ! voice-port 1/0/1 !
The following commands configure dial peers to specify where incoming VoIP calls should be directed. In the first example, a local FXS connection is made to Router A:
dial-peer voice 22 voip destination-pattern 6.... session target ipv4:12.0.0.1 !
This command sets up a connection to the PSTN via a BRI VIC:
dial-peer voice 23 pots destination-pattern 9.... port 1/1/0 !
This command sets up a local BRI connection:
dial-peer voice 24 pots destination-pattern 76003 port 1/0/0 !
This command sets up a connection to a PBX via Router A:
! dial-peer voice 26 voip destination-pattern 5.... session target ipv4:12.0.0.1 !
The following commands configure the Ethernet and serial interfaces:
interface Ethernet0/0 ip address 1.14.122.11 255.255.0.0 no ip directed-broadcast ! interface Serial0/0 ip address 2.0.0.1 255.0.0.0 no ip directed-broadcast no keepalive ! interface Ethernet0/1 ip address 11.0.0.2 255.0.0.0 no ip directed-broadcast ! interface Serial0/1 ip address 14.0.0.2 255.0.0.0 no ip directed-broadcast no keepalive no fair-queue
The following commands configure the BRI interfaces. Note that only one BRI VIC is installed in a voice network module:
! interface BRI1/0 no ip address no ip directed-broadcast isdn switch-type basic-ni1 isdn twait-disable isdn spid1 14085551111 5551111 isdn spid2 14085551112 5551112 isdn incoming-voice modem interface BRI1/1 no ip address no ip directed-broadcast isdn switch-type basic-ni1 isdn twait-disable isdn spid1 14085552111 5552111 isdn spid2 14085552112 5552112 isdn incoming-voice modem ! ip classless ip route 3.0.0.0 255.0.0.0 Ethernet0/1 ip route 3.0.0.0 255.0.0.0 Serial0/1 ip route 223.255.254.0 255.255.255.0 Ethernet0/0 ! ! ! line con 0 exec-timeout 0 0 transport input none line aux 0 line vty 0 4 login ! end vicbri_2600_s2#
All commands used with this feature are documented in the Cisco IOS Release 12.0 command references. The "Configuration Tasks" section illustrates how the commands are used when configuring a BRI VIC for VoIP.
Posted: Tue Jan 4 11:47:29 PST 2000
Copyright 1989-1999©Cisco Systems Inc.