|
|
The registration timeout parameter is now configurable. This configurable timer parameter describes the elapsed time from a cable modem's successful completion of Ranging State 2 to its initial registration request message. During this time, the cable modem establishes IP connectivity, Time of Day, and security (optional), and transfers operational parameters from the Trivial File Transfer Protocol (TFTP) server.
You can now configure the uBR7200 to eliminate conflicts with other timeouts such as TFTP download timeouts.
Table 1 lists the IOS cable router features released in the IOS 12.0 timeframe.
| Available With: | Category | Feature |
|---|---|---|
11.3(5)NA & 12.0(3)T | Cable Features | Feature Enhancements |
11.3(6)NA |
| MC16 Modem Card |
11.3(8)NA |
| Access List Support Enhancements |
12.0(4)T |
| Downstream Channel ID Configuration |
12.0(4)T |
| Multiple Service ID Support |
12.0(4)T |
| Cable Modem and Host Subnet Addressing |
12.0(5)T |
| Telephone Return |
12.0(5)T |
| Time Server Functionality |
12.0(7)T |
| Amplitude Averaging Compensation |
12.0(7)XR |
| Cable Interface Bundling |
12.0(7)XR |
| Enhanced Modem Status Display |
12.0(7)XR |
| Show Interface Cable Command Verbose Enhancements |
12.0(7)XR |
| IP Address Verification |
12.0(7)XR |
| Registration Timeout Configuration |
12.0(7)XR |
| Show Cable Modem Command Enhancements |
12.0(7)XR |
| Modem Status Summary Enhancements |
12.0(7)XR |
| Show Controller Command Enhancements |
12.0(7)XR |
| Configuring Concatenation |
12.0(7)XR |
| Virtual Private Network Support |
12.0(7)XR |
| Blind Hopping Support on the MC16S Modem Card |
12.0(7)XR |
| Signal-to-Noise Ratio Data Support |
11.3(9)NA and 12.0(4)T | Cable QoS | QoS Profile Enforcement |
12.0(4)T |
| Quality of Service for Voice |
11.3(9)NA | Network Management | Upstream Traffic Shaping Feature |
12.0(5)T |
| Enhanced-Spectrum Management |
12.0(5)T |
| Downstream Rate Shaping with TOS bits |
12.0(7)XR |
| Spectrum Management Using the MC16S Modem Card |
12.0(7)XR |
| Downstream Test Signals Configuration |
12.0(7)XR | Wireless Features | Point-to-Point Wireless Support |
The uBR7200 series cable router is described in Voice, Video, and Home Applications Configuration Guide for Cisco IOS Release 12.0 and in the following online feature modules:
uBR7200 series
No new or modified standards are supported by this feature.
No new or modified MIBs are supported by this feature.
No new or modified RFCs are supported by this feature.
See the following tasks to configure the registration timeout value.
| Command | Purpose |
|---|---|
router(config-if)# cable registration-timeout n | Configures the registration timeout values. |
None
To configure the registration timeout, use the cable registration-timeout interface configuration command. To set the timeout value to the default, use the no form of this command.
cable registration-timeout minutes
minutes | Sets the registration timeout. Valid range is from 2 to 60 minutes. |
3 minutes
Interface configuration
| Release | Modification |
|---|---|
12.0(7)XR | This command was introduced. |
The following example shows how you can increase the registration timeout value from 3 minutes to 10 minutes.
router(config-if)# cable registration-timeout 10 router(config-if)#
Posted: Fri Jan 21 20:42:03 PST 2000
Copyright 1989 - 2000©Cisco Systems Inc.