|
|
This section documents new debug commands. All other debug commands used with this feature are documented in the Cisco IOS Release 12.0 Debug Command Reference.
Use the debug fax receive all EXEC command to display Class 2 fax tracing information on all on-ramp fax connections. Use the no form of this command to disable debugging output.
[no] debug fax receive allThis command has no arguments or keywords.
Disabled
| Release | Modification |
|---|---|
12.0(4)T | This command was introduced. |
The following example displays output from the debug fax receive all command. This command, by definition, displays Class 2 information about all on-ramp fax calls as they occur; in this example, only one fax call is being traced.
router# debug fax receive all All fax receptions debugging is on router#
The following output shows that a fax call has come in to the on-ramp gateway, and the on-ramp gateway is verifying calling number (the transmitter), the called number (the receiver) and identifying the appropriate on-ramp dial peer.
*Jan 2 194033.945 csm_check_accept_fax_call calling=4085553414 called=5550847, peer found *Jan 2 194033.945 ftsp_onramp_new_call new call, calling=4085553414, called=5550847
A fax record is created for TTY line 19.
*Jan 2 194033.949 create_fax_record tty19 *Jan 2 194033.949 ftsp_ind_call tty19, peer_tag=400, callid=0x48
Class 2 modem tracing begins, showing that the modem is being initialized.
*Jan 2 194033.949 000000.000 AA *Jan 2 194034.001 000000.052 TT *Jan 2 194034.057 000000.108 Q0E0S0=0 OK
Class 2 modem tracing continues.
*Jan 2 194034.057 000000.108 OK *Jan 2 194037.325 000003.376 RING 000003.376 AT-C0T105 *Jan 2 194037.333 000003.384 OK *Jan 2 194037.333 000003.384 ATT106 *Jan 2 194037.337 000003.388 OK lTE AT+FCLASS=2 *Jan 2 194037.345 000003.396 OK 000003.396 +FDCC=..;+FBOR= *Jan 2 194037.357 000003.412 OK 000003.412 AT+FLID *Jan 2 194037.365 000003.416 OK ATX3DT; *Jan 2 194040.281 000006.332 OK
In the following output, the on-ramp gateway is about to present a dial tone to the user.
about to play dial-tone
In the following output, the on-ramp gateway receives digits form the caller.
*Jan 2 194043.105 000009.156 0 Digit 0 *Jan 2 194043.241 000009.292 1 Digit 1 *Jan 2 194043.389 000009.440 2 Digit 2 *Jan 2 194043.541 000009.592 3 Digit 3 *Jan 2 194043.693 000009.744 4 Digit 4 *Jan 2 194043.841 000009.892 5 Digit 5 *Jan 2 194044.005 000010.056 6 Digit 6 *Jan 2 194044.153 000010.204 7 Digit 7 *Jan 2 194044.305 000010.356 8 Digit 8 *Jan 2 194044.441 000010.492 9 Digit 9 *Jan 2 194044.605 000010.656 0 Digit 0 *Jan 2 194044.741 000010.792 1 Digit 1 *Jan 2 194044.905 000010.956 2 Digit 2 *Jan 2 194045.041 000011.092 3 Digit 3 *Jan 2 194045.193 000011.244 4 Digit 4 *Jan 2 194045.341 000011.392 5 Digit 5 *Jan 2 194045.493 000011.544 6 Digit 6 *Jan 2 194045.641 000011.692 7 Digit 7 *Jan 2 194045.793 000011.844 8 Digit 8 *Jan 2 194045.941 000011.992 9 Digit 9 *Jan 2 194046.093 000012.144 # Digit # *Jan 2 194046.241 000012.292 1 Digit 1 *Jan 2 194046.393 000012.444 4 Digit 4 *Jan 2 194046.541 000012.592 0 Digit 0 *Jan 2 194046.693 000012.744 8 Digit 8 *Jan 2 194046.841 000012.892 5 Digit 5 *Jan 2 194046.993 000013.044 7 Digit 7 *Jan 2 194047.141 000013.192 1 Digit 1 *Jan 2 194047.305 000013.356 0 Digit 0 *Jan 2 194047.441 000013.492 8 Digit 8 *Jan 2 194047.605 000013.656 4 Digit 4 *Jan 2 194047.741 000013.792 7 Digit 7 *Jan 2 194058.393 000024.444 +FCON
The following output shows that the fax call is connected from the on-ramp router to the calling party. Class 2 modem tracing continues.
+FTSI +31 703712194" 1d19h %FTSP-6-FAX_CONNECT Reception *Jan 2 194058.393 RxPhaseA CONNECT *Jan 2 194058.393 CollectDTMF tty=19, ftsp set time=15723604,con time=15726049,tx dur=24450 Redialer Serial Number 01234567890123456789 *Jan 2 194058.393 ftsp_onramp_match_digits tty19, redialer in use *Jan 2 194058.393 ftsp_onramp_match_digits destPat(5710847), matched(7), tag(401) target (mailtotest@nt4server.allegro.com) RxPhaseB RxTSI *Jan 2 194058.665 000024.716 +FDCS0,3,0,2,0,0,0,5 RxPhaseB RxDCS *Jan 2 194100.641 000026.692 OK RxPhaseB OK PhB 000026.692 AT+FDR *Jan 2 194101.949 000028.000 +FCFR +FDCS0,3,0,2,0,0,0,5 RxPhaseB Rx CFR RxPhaseB RxDCS *Jan 2 194102.573 000028.624 CONNECT RxPhaseB RxCon RxPhaseC 000028.624DC2 *Jan 2 194130.761 000056.812 +FPTS1,0 +FET2 OK RxPhaseD RxFPTS RxPhaseD MCF RxPhaseD MODEM_FET *Jan 2 194130.761 RxPhaseD tty=19,ensp set time=15726049,con time=15729286 RxPhaseD Rx EOP RxPhaseD MODEM_OK 000056.812 AT+FDR
The following output shows that the fax transmission is complete.
*Jan 2 194133.469 000059.520 +FHNG00 RxPhaseE Received Hangup Call complete *Jan 2 194133.533 000059.584 OK RxPhaseE Received OK Ending Call
The following output shows that the calling party disconnects following fax transmission.
1d19h %FTSP-6-FAX_DISCONNECT Reception *Jan 2 194133.533 fap_onramp_end_call disconnect- 1d19h %LINK-3-UPDOWN Interface Serial10, changed state to down *Jan 2 194134.537 all booleans set *Jan 2 194134.537 ftsp_do_call_history disc cause=16, Normal connection delete_f_rec() calling free()
| Command | Description |
debug fax receive called-number | Displays Class 2 fax tracing information about on-ramp connections filtered on a specific called number. |
debug fax receive calling-number | Displays Class 2 fax tracing information about on-ramp connections filtered on a specific calling number. |
debug fax receive specific | Enables debug fax receive all command Class 2 fax tracing information to be filtered using the calling number or called number. |
Use the debug fax receive called-number EXEC command to display Class 2 fax tracing information about on-ramp connections filtered on a particular called number. Use the no form of this command to disable debugging output.
[no] debug fax receive called-number {string}
string | Specifies the called telephone number. Valid entries are any series of digits that specify the E.164 telephone number. |
Disabled
| Release | Modification |
|---|---|
12.0(4)T | This command was introduced. |
The following example displays output from the debug fax receive called-number command. In this example, Store and Forward Fax displays Class 2 information about all on-ramp fax calls for the called number 555-0847.
router# debug fax receive specific router# debug fax receive called-number 5550847 All fax receptions debugging is on router#
The following output shows that a fax call has come in to the on-ramp gateway, and the on-ramp gateway is verifying the calling number (the transmitter), the called number (the receiver), and identifying the appropriate on-ramp dial peer.
*Jan 2 194033.945 csm_check_accept_fax_call calling=4085553414 called=5550847, peer found *Jan 2 194033.945 ftsp_onramp_new_call new call, calling=4085553414, called=5550847
A fax record is created for TTY line 19.
*Jan 2 194033.949 create_fax_record tty19 *Jan 2 194033.949 ftsp_ind_call tty19, peer_tag=400, callid=0x48
Class 2 modem tracing begins, showing that the modem is being initialized.
*Jan 2 194033.949 000000.000 AA *Jan 2 194034.001 000000.052 TT *Jan 2 194034.057 000000.108 Q0E0S0=0 OK
Class 2 modem tracing continues.
*Jan 2 194034.057 000000.108 OK *Jan 2 194037.325 000003.376 RING 000003.376 AT-C0T105 *Jan 2 194037.333 000003.384 OK *Jan 2 194037.333 000003.384 ATT106 *Jan 2 194037.337 000003.388 OK lTE AT+FCLASS=2 *Jan 2 194037.345 000003.396 OK 000003.396 +FDCC=..;+FBOR= *Jan 2 194037.357 000003.412 OK 000003.412 AT+FLID *Jan 2 194037.365 000003.416 OK ATX3DT; *Jan 2 194040.281 000006.332 OK
In the following output, the on-ramp gateway is about to present a dial tone to the user.
about to play dial-tone
In the following output, the on-ramp gateway receives digits form the caller.
*Jan 2 194043.105 000009.156 0 Digit 0 *Jan 2 194043.241 000009.292 1 Digit 1 *Jan 2 194043.389 000009.440 2 Digit 2 *Jan 2 194043.541 000009.592 3 Digit 3 *Jan 2 194043.693 000009.744 4 Digit 4 *Jan 2 194043.841 000009.892 5 Digit 5 *Jan 2 194044.005 000010.056 6 Digit 6 *Jan 2 194044.153 000010.204 7 Digit 7 *Jan 2 194044.305 000010.356 8 Digit 8 *Jan 2 194044.441 000010.492 9 Digit 9 *Jan 2 194044.605 000010.656 0 Digit 0 *Jan 2 194044.741 000010.792 1 Digit 1 *Jan 2 194044.905 000010.956 2 Digit 2 *Jan 2 194045.041 000011.092 3 Digit 3 *Jan 2 194045.193 000011.244 4 Digit 4 *Jan 2 194045.341 000011.392 5 Digit 5 *Jan 2 194045.493 000011.544 6 Digit 6 *Jan 2 194045.641 000011.692 7 Digit 7 *Jan 2 194045.793 000011.844 8 Digit 8 *Jan 2 194045.941 000011.992 9 Digit 9 *Jan 2 194046.093 000012.144 # Digit # *Jan 2 194046.241 000012.292 1 Digit 1 *Jan 2 194046.393 000012.444 4 Digit 4 *Jan 2 194046.541 000012.592 0 Digit 0 *Jan 2 194046.693 000012.744 8 Digit 8 *Jan 2 194046.841 000012.892 5 Digit 5 *Jan 2 194046.993 000013.044 7 Digit 7 *Jan 2 194047.141 000013.192 1 Digit 1 *Jan 2 194047.305 000013.356 0 Digit 0 *Jan 2 194047.441 000013.492 8 Digit 8 *Jan 2 194047.605 000013.656 4 Digit 4 *Jan 2 194047.741 000013.792 7 Digit 7 *Jan 2 194058.393 000024.444 +FCON
The following output shows that the fax call is connected from the on-ramp router to the calling party. Class 2 modem tracing continues.
+FTSI +31 703712194" 1d19h %FTSP-6-FAX_CONNECT Reception *Jan 2 194058.393 RxPhaseA CONNECT *Jan 2 194058.393 CollectDTMF tty=19, ftsp set time=15723604,con time=15726049,tx dur=24450 Redialer Serial Number 01234567890123456789 *Jan 2 194058.393 ftsp_onramp_match_digits tty19, redialer in use *Jan 2 194058.393 ftsp_onramp_match_digits destPat(5710847), matched(7), tag(401) target (mailtotest@nt4server.allegro.com) RxPhaseB RxTSI *Jan 2 194058.665 000024.716 +FDCS0,3,0,2,0,0,0,5 RxPhaseB RxDCS *Jan 2 194100.641 000026.692 OK RxPhaseB OK PhB 000026.692 AT+FDR *Jan 2 194101.949 000028.000 +FCFR +FDCS0,3,0,2,0,0,0,5 RxPhaseB Rx CFR RxPhaseB RxDCS *Jan 2 194102.573 000028.624 CONNECT RxPhaseB RxCon RxPhaseC 000028.624DC2 *Jan 2 194130.761 000056.812 +FPTS1,0 +FET2 OK RxPhaseD RxFPTS RxPhaseD MCF RxPhaseD MODEM_FET *Jan 2 194130.761 RxPhaseD tty=19,ensp set time=15726049,con time=15729286 RxPhaseD Rx EOP RxPhaseD MODEM_OK 000056.812 AT+FDR
The following output shows that the fax transmission is complete.
*Jan 2 194133.469 000059.520 +FHNG00 RxPhaseE Received Hangup Call complete *Jan 2 194133.533 000059.584 OK RxPhaseE Received OK Ending Call
The following output shows that the calling party disconnects following fax transmission.
1d19h %FTSP-6-FAX_DISCONNECT Reception *Jan 2 194133.533 fap_onramp_end_call disconnect- 1d19h %LINK-3-UPDOWN Interface Serial10, changed state to down *Jan 2 194134.537 all booleans set *Jan 2 194134.537 ftsp_do_call_history disc cause=16, Normal connection delete_f_rec() calling free()
| Command | Description |
debug fax receive all | Displays Class 2 fax tracing information about all on-ramp connections. |
debug fax receive calling-number | Displays Class 2 fax tracing information about on-ramp connections filtered on a specific calling number. |
debug fax receive specific | Enables debug fax receive all command Class 2 fax tracing information to be filtered using the calling number or called number. |
Use the debug fax receive calling-number EXEC command to display Class 2 fax tracing information about on-ramp connections filtering on a particular calling number. Use the no form of this command to disable debugging output.
[no] debug fax receive calling-number {string}
string | Specifies the calling telephone number. Valid entries are any series of digits that specify the E.164 telephone number. |
Disabled
| Release | Modification |
|---|---|
12.0(4)T | This command was introduced. |
The following example displays output from the debug fax receive calling-number command. In this example, Store and Forward Fax displays Class 2 information about all on-ramp fax calls for the calling number 408 555-3414.
router# debug fax receive specific router# debug fax receive calling-number 4085553414 All fax receptions debugging is on router#
The following output shows that a fax call has come in to the on-ramp gateway, and the on-ramp gateway is verifying the calling number (the transmitter), the called number (the receiver) and identifying the appropriate on-ramp dial peer.
*Jan 2 194033.945 csm_check_accept_fax_call calling=4085553414 called=5550847, peer found *Jan 2 194033.945 ftsp_onramp_new_call new call, calling=4085553414, called=5550847
A fax record is created for TTY line 19.
*Jan 2 194033.949 create_fax_record tty19 *Jan 2 194033.949 ftsp_ind_call tty19, peer_tag=400, callid=0x48
Class 2 modem tracing begins, showing that the modem is being initialized.
*Jan 2 194033.949 000000.000 AA *Jan 2 194034.001 000000.052 TT *Jan 2 194034.057 000000.108 Q0E0S0=0 OK
Class 2 modem tracing continues.
*Jan 2 194034.057 000000.108 OK *Jan 2 194037.325 000003.376 RING 000003.376 AT-C0T105 *Jan 2 194037.333 000003.384 OK *Jan 2 194037.333 000003.384 ATT106 *Jan 2 194037.337 000003.388 OK lTE AT+FCLASS=2 *Jan 2 194037.345 000003.396 OK 000003.396 +FDCC=..;+FBOR= *Jan 2 194037.357 000003.412 OK 000003.412 AT+FLID *Jan 2 194037.365 000003.416 OK ATX3DT; *Jan 2 194040.281 000006.332 OK
In the following output, the on-ramp gateway is about to present a dial tone to the user.
about to play dial-tone
In the following output, the on-ramp gateway receives digits form the caller.
*Jan 2 194043.105 000009.156 0 Digit 0 *Jan 2 194043.241 000009.292 1 Digit 1 *Jan 2 194043.389 000009.440 2 Digit 2 *Jan 2 194043.541 000009.592 3 Digit 3 *Jan 2 194043.693 000009.744 4 Digit 4 *Jan 2 194043.841 000009.892 5 Digit 5 *Jan 2 194044.005 000010.056 6 Digit 6 *Jan 2 194044.153 000010.204 7 Digit 7 *Jan 2 194044.305 000010.356 8 Digit 8 *Jan 2 194044.441 000010.492 9 Digit 9 *Jan 2 194044.605 000010.656 0 Digit 0 *Jan 2 194044.741 000010.792 1 Digit 1 *Jan 2 194044.905 000010.956 2 Digit 2 *Jan 2 194045.041 000011.092 3 Digit 3 *Jan 2 194045.193 000011.244 4 Digit 4 *Jan 2 194045.341 000011.392 5 Digit 5 *Jan 2 194045.493 000011.544 6 Digit 6 *Jan 2 194045.641 000011.692 7 Digit 7 *Jan 2 194045.793 000011.844 8 Digit 8 *Jan 2 194045.941 000011.992 9 Digit 9 *Jan 2 194046.093 000012.144 # Digit # *Jan 2 194046.241 000012.292 1 Digit 1 *Jan 2 194046.393 000012.444 4 Digit 4 *Jan 2 194046.541 000012.592 0 Digit 0 *Jan 2 194046.693 000012.744 8 Digit 8 *Jan 2 194046.841 000012.892 5 Digit 5 *Jan 2 194046.993 000013.044 7 Digit 7 *Jan 2 194047.141 000013.192 1 Digit 1 *Jan 2 194047.305 000013.356 0 Digit 0 *Jan 2 194047.441 000013.492 8 Digit 8 *Jan 2 194047.605 000013.656 4 Digit 4 *Jan 2 194047.741 000013.792 7 Digit 7 *Jan 2 194058.393 000024.444 +FCON
The following output shows that the fax call is connected from the on-ramp router to the calling party. Class 2 modem tracing continues.
+FTSI +31 703712194" 1d19h %FTSP-6-FAX_CONNECT Reception *Jan 2 194058.393 RxPhaseA CONNECT *Jan 2 194058.393 CollectDTMF tty=19, ftsp set time=15723604,con time=15726049,tx dur=24450 Redialer Serial Number 01234567890123456789 *Jan 2 194058.393 ftsp_onramp_match_digits tty19, redialer in use *Jan 2 194058.393 ftsp_onramp_match_digits destPat(5710847), matched(7), tag(401) target (mailtotest@nt4server.allegro.com) RxPhaseB RxTSI *Jan 2 194058.665 000024.716 +FDCS0,3,0,2,0,0,0,5 RxPhaseB RxDCS *Jan 2 194100.641 000026.692 OK RxPhaseB OK PhB 000026.692 AT+FDR *Jan 2 194101.949 000028.000 +FCFR +FDCS0,3,0,2,0,0,0,5 RxPhaseB Rx CFR RxPhaseB RxDCS *Jan 2 194102.573 000028.624 CONNECT RxPhaseB RxCon RxPhaseC 000028.624DC2 *Jan 2 194130.761 000056.812 +FPTS1,0 +FET2 OK RxPhaseD RxFPTS RxPhaseD MCF RxPhaseD MODEM_FET *Jan 2 194130.761 RxPhaseD tty=19,ensp set time=15726049,con time=15729286 RxPhaseD Rx EOP RxPhaseD MODEM_OK 000056.812 AT+FDR
The following output shows that the fax transmission is complete.
*Jan 2 194133.469 000059.520 +FHNG00 RxPhaseE Received Hangup Call complete *Jan 2 194133.533 000059.584 OK RxPhaseE Received OK Ending Call
The following output shows that the calling party disconnects following fax transmission.
1d19h %FTSP-6-FAX_DISCONNECT Reception *Jan 2 194133.533 fap_onramp_end_call disconnect- 1d19h %LINK-3-UPDOWN Interface Serial10, changed state to down *Jan 2 194134.537 all booleans set *Jan 2 194134.537 ftsp_do_call_history disc cause=16, Normal connection delete_f_rec() calling free()
| Command | Description |
debug fax receive all | Displays Class 2 fax tracing information about all on-ramp connections. |
debug fax receive called-number | Displays Class 2 fax tracing information about on-ramp connections filtered on a specific called number. |
debug fax receive specific | Enables debug fax receive all command Class 2 fax tracing information to be filtered using the calling number or called number. |
Use the debug fax receive specific EXEC command to enable Class 2 fax protocol tracing information for on-ramp activities to be filtered using either a calling or called number. Use the no form of this command to disable filtering debugging output.
[no] debug fax receive specificThis command has no arguments or keywords.
Disabled
| Release | Modification |
|---|---|
12.0(4)T | This command was introduced. |
The following example displays output from the debug fax receive calling-number command, which is enabled using the debug fax receive specific command. In this example, Store and Forward Fax displays Class 2 information about all on-ramp fax calls for the calling number 408 555-3414.
router# debug fax receive specific router# debug fax receive calling-number 4085553414 All fax receptions debugging is on router#
The following output shows that a fax call has come in to the on-ramp gateway, and the on-ramp gateway is verifying the calling number (the transmitter), the called number (the receiver) and identifying the appropriate on-ramp dial peer.
*Jan 2 194033.945 csm_check_accept_fax_call calling=4085553414 called=5550847, peer found *Jan 2 194033.945 ftsp_onramp_new_call new call, calling=4085553414, called=5550847
A fax record is created for TTY line 19.
*Jan 2 194033.949 create_fax_record tty19 *Jan 2 194033.949 ftsp_ind_call tty19, peer_tag=400, callid=0x48
Class 2 modem tracing begins, showing that the modem is being initialized.
*Jan 2 194033.949 000000.000 AA *Jan 2 194034.001 000000.052 TT *Jan 2 194034.057 000000.108 Q0E0S0=0 OK
Class 2 modem tracing continues.
*Jan 2 194034.057 000000.108 OK *Jan 2 194037.325 000003.376 RING 000003.376 AT-C0T105 *Jan 2 194037.333 000003.384 OK *Jan 2 194037.333 000003.384 ATT106 *Jan 2 194037.337 000003.388 OK lTE AT+FCLASS=2 *Jan 2 194037.345 000003.396 OK 000003.396 +FDCC=..;+FBOR= *Jan 2 194037.357 000003.412 OK 000003.412 AT+FLID *Jan 2 194037.365 000003.416 OK ATX3DT; *Jan 2 194040.281 000006.332 OK
In the following output, the on-ramp gateway is about to present a dial tone to the user.
about to play dial-tone
In the following output, the on-ramp gateway receives digits form the caller.
*Jan 2 194043.105 000009.156 0 Digit 0 *Jan 2 194043.241 000009.292 1 Digit 1 *Jan 2 194043.389 000009.440 2 Digit 2 *Jan 2 194043.541 000009.592 3 Digit 3 *Jan 2 194043.693 000009.744 4 Digit 4 *Jan 2 194043.841 000009.892 5 Digit 5 *Jan 2 194044.005 000010.056 6 Digit 6 *Jan 2 194044.153 000010.204 7 Digit 7 *Jan 2 194044.305 000010.356 8 Digit 8 *Jan 2 194044.441 000010.492 9 Digit 9 *Jan 2 194044.605 000010.656 0 Digit 0 *Jan 2 194044.741 000010.792 1 Digit 1 *Jan 2 194044.905 000010.956 2 Digit 2 *Jan 2 194045.041 000011.092 3 Digit 3 *Jan 2 194045.193 000011.244 4 Digit 4 *Jan 2 194045.341 000011.392 5 Digit 5 *Jan 2 194045.493 000011.544 6 Digit 6 *Jan 2 194045.641 000011.692 7 Digit 7 *Jan 2 194045.793 000011.844 8 Digit 8 *Jan 2 194045.941 000011.992 9 Digit 9 *Jan 2 194046.093 000012.144 # Digit # *Jan 2 194046.241 000012.292 1 Digit 1 *Jan 2 194046.393 000012.444 4 Digit 4 *Jan 2 194046.541 000012.592 0 Digit 0 *Jan 2 194046.693 000012.744 8 Digit 8 *Jan 2 194046.841 000012.892 5 Digit 5 *Jan 2 194046.993 000013.044 7 Digit 7 *Jan 2 194047.141 000013.192 1 Digit 1 *Jan 2 194047.305 000013.356 0 Digit 0 *Jan 2 194047.441 000013.492 8 Digit 8 *Jan 2 194047.605 000013.656 4 Digit 4 *Jan 2 194047.741 000013.792 7 Digit 7 *Jan 2 194058.393 000024.444 +FCON
The following output shows that the fax call is connected from the on-ramp router to the calling party. Class 2 modem tracing continues.
+FTSI +31 703712194" 1d19h %FTSP-6-FAX_CONNECT Reception *Jan 2 194058.393 RxPhaseA CONNECT *Jan 2 194058.393 CollectDTMF tty=19, ftsp set time=15723604,con time=15726049,tx dur=24450 Redialer Serial Number 01234567890123456789 *Jan 2 194058.393 ftsp_onramp_match_digits tty19, redialer in use *Jan 2 194058.393 ftsp_onramp_match_digits destPat(5710847), matched(7), tag(401) target (mailtotest@nt4server.allegro.com) RxPhaseB RxTSI *Jan 2 194058.665 000024.716 +FDCS0,3,0,2,0,0,0,5 RxPhaseB RxDCS *Jan 2 194100.641 000026.692 OK RxPhaseB OK PhB 000026.692 AT+FDR *Jan 2 194101.949 000028.000 +FCFR +FDCS0,3,0,2,0,0,0,5 RxPhaseB Rx CFR RxPhaseB RxDCS *Jan 2 194102.573 000028.624 CONNECT RxPhaseB RxCon RxPhaseC 000028.624DC2 *Jan 2 194130.761 000056.812 +FPTS1,0 +FET2 OK RxPhaseD RxFPTS RxPhaseD MCF RxPhaseD MODEM_FET *Jan 2 194130.761 RxPhaseD tty=19,ensp set time=15726049,con time=15729286 RxPhaseD Rx EOP RxPhaseD MODEM_OK 000056.812 AT+FDR
The following output shows that the fax transmission is complete.
*Jan 2 194133.469 000059.520 +FHNG00 RxPhaseE Received Hangup Call complete *Jan 2 194133.533 000059.584 OK RxPhaseE Received OK Ending Call
The following output shows that the calling party disconnects following fax transmission.
1d19h %FTSP-6-FAX_DISCONNECT Reception *Jan 2 194133.533 fap_onramp_end_call disconnect- 1d19h %LINK-3-UPDOWN Interface Serial10, changed state to down *Jan 2 194134.537 all booleans set *Jan 2 194134.537 ftsp_do_call_history disc cause=16, Normal connection delete_f_rec() calling free()
| Command | Description |
debug fax receive all | Displays Class 2 fax tracing information about all on-ramp connections. |
debug fax receive called-number | Displays Class 2 fax tracing information about on-ramp connections filtered on a specific called number. |
debug fax receive calling-number | Displays Class 2 fax tracing information about on-ramp connections filtered on a specific calling number. |
Use the debug fax send all EXEC command to display Class 2 fax protocol tracing information for all off-ramp faxing activities. Use the no form of this command to disable debugging output.
[no] debug fax send allThis command has no arguments or keywords.
Disabled
| Release | Modification |
|---|---|
12.0(4)T | This command was introduced. |
The following example displays output from the debug fax send all command. This command, by definition, displays Class 2 information about all off-ramp fax calls as they occur; in this example, only one fax call is being traced.
router# debug fax send all
The following output shows that the off-ramp gateway is placing a fax call.
*Jan 1 175435.703 ftsp_offramp_match_digits phone number to translate 5553413 *Jan 1 175435.703 destPat(5553413), matched(6), prefix() peer_tag(310) *Jan 1 175435.703 ftsp_offramp_match_digits target 5763413 *Jan 1 175435.743 fap_offcm tty(72), Got dial message000000.000 AT&F\Q0S7=255
Class 2 modem tracing begins, including modem initialization.
000000.080 A 000000.096 T 000000.128 &F 000000.144 \Q 000000.160 0S7=255 000000.160 OK
In the following output, Class 2 modem tracing continues.
000000.160 E0V1 000000.192 A 000000.192 TE 000000.208 0 000000.208 OK 000000.208AT+FCLASS=2 000000.288 OK 000000.288 +FDCC=..;+FBOR= 000000.368 OK 000000.368 AT+FLID 000000.432 OK
The following output shows that the off-ramp gateway is dialing out.
000000.432 ATDTW5553413 *Jan 1 175436.419 ftsp_setup_for_oc tty72, callid=0x1C *Jan 1 175436.419 ftsp_setup_for_oc ctl=2, cas grp=-1, snmp_ix=102 *Jan 1 175436.419 ftsp_off_ramp_active_call_init tty72 callid=0x1C,
The following output identifies the SMNP index of the off-ramp device.
snmp_ix=102 000011.784 +FCON Phase A Start
The following output shows that the called party has answered and that the fax transmission is beginning. Class 2 modem tracing continues.
175449 %FTSP-6-FAX_CONNECT Transmission *Jan 1 175447.527 TxPhaseA MODEM_FCON 000012.524 +FNSFB5 00 2E 57 46 58 3A 37 2E 30 Phase B Start TxPhaseB MODEM_FNSF 000013.276 +FCSI" Allegro Fax machine" Phase B Start TxPhaseB MODEM_FCSI 000013.756 +FDIS1,5,0,2,3,0,1,0 OK Phase B Start TxPhaseB MODEM_FDIS TxPhaseB MODEM_OK *Jan 1 175449.499 TxPhaseB, tty(72), Tx Speed=14400bps *Jan 1 175449.499 000013.756 AT+FDIS 000013.820 OK Phase B Start TxPhaseB MODEM_OK 000013.820 AT+FDT 000020.704 +FDCS0,5,0,2,0,0,0,0 Phase B Start TxPhaseB MODEM_FDCS *Jan 1 175456.447 calc_min_line_bytes normal resolution 000021.280 CONNECT Phase B Start TxPhaseB MODEM_CONNECT 000021.296 Phase C Start TxPhaseC MODEM_XON *Jan 1 175457.139 asfax_txservice tty(72), MPS b000024.788 OK Tx Phase D Start TxPhaseD MODEM_OK Tx Phase D MPS 000027.128 +FPTS1 OK Tx Phase D Start TxPhaseD MODEM_FPTS RxFPTS +FPTS1 TxPhaseD MCF TxPhaseD MPS Phase C Start TxPhaseC MODEM_OK 000027.768 CONNECT Phase C Start TxPhaseC MODEM_CONNECT 000027.784 Phase C Start TxPhaseC MODEM_XON *Jan 1 175503.687 asfax_txservice tty(72), EOP000032.444 OK Tx Phase D Start TxPhaseD MODEM_OK Tx Phase D EOP 000034.716 +FPTS1 Tx Phase D Start TxPhaseD MODEM_FPTS RxFPTS +FPTS1 TxPhaseD MCF Enabling smtp for receiving data, body_page_number 2, body_page_number_sent 1 000036.272 +FHNG0 TxPhaseE MODEM_FHNG 000036.832 OK TxPhaseE MODEM_OK
The following output shows that the fax transmission is complete.
175514 %FTSP-6-FAX_DISCONNECT Transmission *Jan 1 175512.575 tty(72) fax transmit done 175514 %LINK-3-UPDOWN Interface Serial222, changed state to down
| Command | Description |
debug fax send calling-number | Displays Class 2 fax tracing information about off-ramp connections filtered on a specific called number. |
debug fax send specific | Enables debug fax send all command Class 2 fax tracing information to be filtered using the calling number. |
Use the debug fax send calling-number EXEC command to display information for a particular outbound calling number. Use the no form of this command to disable debugging output.
[no] debug fax send calling-number {string}
string | Specifies the telephone number to which the fax transmission was sent. Valid entries are any series of digits that specify the E.164 telephone number. |
Disabled
| Release | Modification |
|---|---|
12.o(4)T | This command was introduced. |
The following example displays output from the debug fax send calling-number command. In this example, Store and Forward Fax displays Class 2 information about all off-ramp fax calls for the calling number 555-3414.
router# debug fax send specific router# debug fax send calling-number 5553413
The following output shows that the off-ramp gateway is placing a fax call.
*Jan 1 175435.703 ftsp_offramp_match_digits phone number to translate 5553413 *Jan 1 175435.703 destPat(5553413), matched(6), prefix() peer_tag(310) *Jan 1 175435.703 ftsp_offramp_match_digits target 5553413 *Jan 1 175435.743 fap_offcm tty(72), Got dial message000000.000 AT&F\Q0S7=255
Class 2 modem tracing begins, including modem initialization.
000000.080 A 000000.096 T 000000.128 &F 000000.144 \Q 000000.160 0S7=255 000000.160 OK
In the following output, Class 2 modem tracing continues.
000000.160 E0V1 000000.192 A 000000.192 TE 000000.208 0 000000.208 OK 000000.208AT+FCLASS=2 000000.288 OK 000000.288 +FDCC=..;+FBOR= 000000.368 OK 000000.368 AT+FLID 000000.432 OK
The following output shows that the off-ramp gateway is dialing out.
000000.432 ATDTW5553413 *Jan 1 175436.419 ftsp_setup_for_oc tty72, callid=0x1C *Jan 1 175436.419 ftsp_setup_for_oc ctl=2, cas grp=-1, snmp_ix=102 *Jan 1 175436.419 ftsp_off_ramp_active_call_init tty72 callid=0x1C,
The following output identifies the SMNP index of the off-ramp device.
snmp_ix=102 000011.784 +FCON Phase A Start
The following output shows that the called party has answered and that the fax transmission is beginning. Class 2 modem tracing continues.
175449 %FTSP-6-FAX_CONNECT Transmission *Jan 1 175447.527 TxPhaseA MODEM_FCON 000012.524 +FNSFB5 00 2E 57 46 58 3A 37 2E 30 Phase B Start TxPhaseB MODEM_FNSF 000013.276 +FCSI" Allegro Fax machine" Phase B Start TxPhaseB MODEM_FCSI 000013.756 +FDIS1,5,0,2,3,0,1,0 OK Phase B Start TxPhaseB MODEM_FDIS TxPhaseB MODEM_OK *Jan 1 175449.499 TxPhaseB, tty(72), Tx Speed=14400bps *Jan 1 175449.499 000013.756 AT+FDIS 000013.820 OK Phase B Start TxPhaseB MODEM_OK 000013.820 AT+FDT 000020.704 +FDCS0,5,0,2,0,0,0,0 Phase B Start TxPhaseB MODEM_FDCS *Jan 1 175456.447 calc_min_line_bytes normal resolution 000021.280 CONNECT Phase B Start TxPhaseB MODEM_CONNECT 000021.296 Phase C Start TxPhaseC MODEM_XON *Jan 1 175457.139 asfax_txservice tty(72), MPS b000024.788 OK Tx Phase D Start TxPhaseD MODEM_OK Tx Phase D MPS 000027.128 +FPTS1 OK Tx Phase D Start TxPhaseD MODEM_FPTS RxFPTS +FPTS1 TxPhaseD MCF TxPhaseD MPS Phase C Start TxPhaseC MODEM_OK 000027.768 CONNECT Phase C Start TxPhaseC MODEM_CONNECT 000027.784 Phase C Start TxPhaseC MODEM_XON *Jan 1 175503.687 asfax_txservice tty(72), EOP000032.444 OK Tx Phase D Start TxPhaseD MODEM_OK Tx Phase D EOP 000034.716 +FPTS1 Tx Phase D Start TxPhaseD MODEM_FPTS RxFPTS +FPTS1 TxPhaseD MCF Enabling smtp for receiving data, body_page_number 2, body_page_number_sent 1 000036.272 +FHNG0 TxPhaseE MODEM_FHNG 000036.832 OK TxPhaseE MODEM_OK
The following output shows that the fax transmission is complete.
175514 %FTSP-6-FAX_DISCONNECT Transmission *Jan 1 175512.575 tty(72) fax transmit done 175514 %LINK-3-UPDOWN Interface Serial222, changed state to down
| Command | Description |
debug fax send all | Displays Class 2 fax tracing information about all off-ramp connections. |
debug fax send specific | Enables debug fax send all command Class 2 fax tracing information to be filtered using the calling number. |
Use the debug fax send specific EXEC command to enable filtering information on an outbound calling number. Use the no form of this command to disable debugging output.
[no] debug fax send specificThis command uses no arguments or keywords.
Disabled
| Release | Modification |
|---|---|
12.0(4)T | This command was introduced. |
The following example displays output from the debug fax send calling-number command, which has been enabled by using the debug fax send specific command. In this example, Store and Forward Fax displays Class 2 information about all off-ramp fax calls for the calling number 555-3414.
router# debug fax send specific router# debug fax send calling-number 5553414
The following output shows that the off-ramp gateway is placing a fax call.
*Jan 1 175435.703 ftsp_offramp_match_digits phone number to translate 5553413 *Jan 1 175435.703 destPat(5553413), matched(6), prefix() peer_tag(310) *Jan 1 175435.703 ftsp_offramp_match_digits target 5763413 *Jan 1 175435.743 fap_offcm tty(72), Got dial message000000.000 AT&F\Q0S7=255
Class 2 modem tracing begins, including modem initialization.
000000.080 A 000000.096 T 000000.128 &F 000000.144 \Q 000000.160 0S7=255 000000.160 OK
In the following output, Class 2 modem tracing continues.
000000.160 E0V1 000000.192 A 000000.192 TE 000000.208 0 000000.208 OK 000000.208AT+FCLASS=2 000000.288 OK 000000.288 +FDCC=..;+FBOR= 000000.368 OK 000000.368 AT+FLID 000000.432 OK
The following output shows that the off-ramp gateway is dialing out.
000000.432 ATDTW5553413 *Jan 1 175436.419 ftsp_setup_for_oc tty72, callid=0x1C *Jan 1 175436.419 ftsp_setup_for_oc ctl=2, cas grp=-1, snmp_ix=102 *Jan 1 175436.419 ftsp_off_ramp_active_call_init tty72 callid=0x1C,
The following output identifies the SMNP index of the off-ramp device.
snmp_ix=102 000011.784 +FCON Phase A Start
The following output shows that the called party has answered and that the fax transmission is beginning. Class 2 modem tracing continues.
175449 %FTSP-6-FAX_CONNECT Transmission *Jan 1 175447.527 TxPhaseA MODEM_FCON 000012.524 +FNSFB5 00 2E 57 46 58 3A 37 2E 30 Phase B Start TxPhaseB MODEM_FNSF 000013.276 +FCSI" Allegro Fax machine" Phase B Start TxPhaseB MODEM_FCSI 000013.756 +FDIS1,5,0,2,3,0,1,0 OK Phase B Start TxPhaseB MODEM_FDIS TxPhaseB MODEM_OK *Jan 1 175449.499 TxPhaseB, tty(72), Tx Speed=14400bps *Jan 1 175449.499 000013.756 AT+FDIS 000013.820 OK Phase B Start TxPhaseB MODEM_OK 000013.820 AT+FDT 000020.704 +FDCS0,5,0,2,0,0,0,0 Phase B Start TxPhaseB MODEM_FDCS *Jan 1 175456.447 calc_min_line_bytes normal resolution 000021.280 CONNECT Phase B Start TxPhaseB MODEM_CONNECT 000021.296 Phase C Start TxPhaseC MODEM_XON *Jan 1 175457.139 asfax_txservice tty(72), MPS b000024.788 OK Tx Phase D Start TxPhaseD MODEM_OK Tx Phase D MPS 000027.128 +FPTS1 OK Tx Phase D Start TxPhaseD MODEM_FPTS RxFPTS +FPTS1 TxPhaseD MCF TxPhaseD MPS Phase C Start TxPhaseC MODEM_OK 000027.768 CONNECT Phase C Start TxPhaseC MODEM_CONNECT 000027.784 Phase C Start TxPhaseC MODEM_XON *Jan 1 175503.687 asfax_txservice tty(72), EOP000032.444 OK Tx Phase D Start TxPhaseD MODEM_OK Tx Phase D EOP 000034.716 +FPTS1 Tx Phase D Start TxPhaseD MODEM_FPTS RxFPTS +FPTS1 TxPhaseD MCF Enabling smtp for receiving data, body_page_number 2, body_page_number_sent 1 000036.272 +FHNG0 TxPhaseE MODEM_FHNG 000036.832 OK TxPhaseE MODEM_OK
The following output shows that the fax transmission is complete.
175514 %FTSP-6-FAX_DISCONNECT Transmission *Jan 1 175512.575 tty(72) fax transmit done 175514 %LINK-3-UPDOWN Interface Serial222, changed state to down
| Command | Description |
debug fax send all | Displays Class 2 fax tracing information about all off-ramp connections. |
debug fax send calling-number | Displays Class 2 fax tracing information about off-ramp connections filtered on a specific called number. |
Use the debug fmail client command to display e-mail parameters (such as Mail from and Envelope to and Envelope from) as well as the progress of the SMTP client. Use the no form of this command to disable debugging output.
[no] debug fmail clientThis command uses no arguments or keywords.
Disabled
| Release | Modification |
|---|---|
12.0(4)T | This command was introduced. |
The following example shows how the debug fmail client command traces the component that communicates with the SMTP client on the on-ramp Cisco AS5300.
router# debug fmail client
In the following output, the fax-mail client is trying to establish a session with an e-mail server.
*Jan 1 18:04:39.419: fmccm: tty(1), establishing a connection *Jan 1 18:04:39.419: fmccm tty(1): Envelope to: uut1@linux2.allegro.com *Jan 1 18:04:39.419: fmccm tty(1), Mail from user name is fully specified *Jan 1 18:04:39.419: fmccm: tty(1), Envelope from: FAX=4085763413@allegrouut1.allegro.com
In the following output, the fax-mail client opens a session with e-mail server.
*Jan 1 18:04:39.423: fmccm: Opening connection with email host 14.0.0.4 *Jan 1 18:04:39.423: ensp_ind_call: tty1 peer_tag=110 onRamp 18:04:50: %FTSP-6-FAX_CONNECT: Reception 18:05:01: %FTSP-6-FAX_DISCONNECT: Reception *Jan 1 18:04:59.043: fm_cpd:: tty(1),Received TIFF_PAGE_READY messagfm_cpd:: tty(1), Received TIFF_PAGE_READY message *Jan 1 18:04:59.043: fm_cpd:: tty(1),END_OF_FAX_PAGE received *Jan 1 18:04:59.043: fm_cpd:: tty(1),Received TIFF_PAGE_READY messagfm_cpd:: tty(1), Received TIFF_PAGE_READY message 18:05:01: %LINK-3-UPDOWN: Interface Serial2:0, changed state to down *Jan 1 18:05:00.831: fmcbfc: tty(1): esmtp response status 0 *Jan 1 18:05:00.831: fmcbfc:: tty(1), Faxmail message id = 002D2000180439695@allegrouut1.allegro.com *Jan 1 18:05:00.831: fmcbfc: tty(1): Calling fap_onramp_process_boolean() for cleanup *Jan 1 18:05:00.831: ensp_do_call_history: disc cause=63, service or option not available, unspecified
| Command | Description |
debug fmail server | Displays communications with the SMTP server. |
Use the debug fmail server EXEC command to display communication with the SMTP server. Use the no form of this command to disable debugging output.
[no] debug fmail serverThis command uses no arguments or keywords.
Disabled
| Release | Modification |
|---|---|
12.0(4)T | This command was introduced. |
The following output shows how the debug fmail server command provides information about cover-page generation and progress of the data that the off-ramp Cisco AS5300 is processing from the SMTP server.
router# debug fmail server
In the following output, the off-ramp gateway receives an e-mail message from a mail server.
from uut1@linux2.allegro.com, ph#in fax=5553413 *Jan 1 175725.383 decode_minaddr (pstn fax=5553413) *Jan 1 175725.383 decode_minaddr Fax Number5553413 *Jan 1 175725.383 decode_minaddr phone string returned [5763413]tel_number_dial 5763413 *Jan 1 175725.383 create fax payload *Jan 1 175725.383 ensp_ind_call offRamp *Jan 1 175725.383 Entering faxmail_server_new_recipient() *Jan 1 175725.383 envelope_to 35, [fax=5763413@allegrouut1.allegro.com] *Jan 1 175725.383 allocate_modem mica_last_used 72 *Jan 1 175725.383 allocate_modem microcom_last_used 0 *Jan 1 175725.383 statbits 10420
In the following output, the off-ramp gateway looks for a free modem.
*Jan 1 175725.383 statbits2 5 *Jan 1 175725.383 statbits 10420 *Jan 1 175725.383 statbits2 5 *Jan 1 175725.383 statbits 10420 *Jan 1 175725.383 statbits2 5 *Jan 1 175725.383 statbits 10420 *Jan 1 175725.383 statbits2 5 *Jan 1 175725.383 statbits 10420 *Jan 1 175725.387 statbits2 5 *Jan 1 175725.387 statbits 10020 *Jan 1 175725.387 statbits2 1
In the following output, the off-ramp gateway finds and seizes an available MICA modem.
*Jan 1 175725.387 allocate_modem found a mica modem *Jan 1 175725.391 allocate_modem seizing modem 72 *Jan 1 175725.391 create_fax_record tty72 *Jan 1 175725.391 cover page is enabled for fax=5763413@allegrouut1.allegro.com *Jan 1 175725.391 fax_record->tel_number_dial 5763413 *Jan 1 175725.391 Total rcpt so far 1 rfc_payload->envelope_from 24, [uut1@linux2.allegro.com]
In the following output, the off-ramp gateway matches the MMoIP dial peer information.
*Jan 1 175725.399 ensp_offramp_match_digits destPat(5763413), matched(6), tag(300) target () *Jan 1 175725.399 decode_minaddr (pstn fax=5763413@allegrouut1.allegro.com) *Jan 1 175725.399 decode_minaddr Fax Number5763413 *Jan 1 175725.399 decode_minaddr phone string returned [5763413]from_personal_name 4, [uut1] cover_page_from1 8, ["uut1", ] *Jan 1 175725.399 >>> from_raw 23, [uut1@linux2.allegro.com] *Jan 1 175725.399 Non-digit character encountered [u]cover_page_from2 [uut1@linux2.allegro.com]
In the following output, the off-ramp gateway displays the data included in the Store and Forward Fax-generated cover page.
//Cover page -------------------------------------------------------------------------------- Title: This is the offramp To: 5553413 From: "uut1", uut1@linux2.allegro.com Date: Thu, 21 Jan 1999 10:44:21 -0800 Subject: test -------------------------------------------------------------------------------- ] *Jan 1 17:57:25.399: Calling text2fax_data_handler for cover page *Jan 1 17:57:25.411: Returned buffer length: 1548 (mime != text) *Jan 1 17:57:25.411: faxmail_server_put_buffer: buffer_info == BUFF_END_OF_PART *Jan 1 17:57:25.415: Returned buffer length: 1548 (mime != text) *Jan 1 17:57:25.415: faxmail_server_put_buffer: buffer_info == BUFF_END_OF_PART *Jan 1 17:57:25.415: Returned buffer length: 624 (mime == text) *Jan 1 17:57:25.415: faxmail_server_put_buffer: buffer_info == BUFF_END_OF_PART *Jan 1 17:57:25.415: [ test ] *Jan 1 17:57:25.415: Calling text2fax_data_handler - TEXT_BODY_PAGE *Jan 1 17:57:25.431: Authentication bypassed....not enabled
In the following output, the off-ramp gateway places the call to the receiving fax machine.
*Jan 1 17:57:25.431: Sending dial messages now *Jan 1 17:57:25.431: faxmail_server_send_dial_message to fap 5763413 *Jan 1 17:57:25.431: send DIAL *Jan 1 17:57:25.535: Returned buffer length: 1548 (mime != text) *Jan 1 17:57:25.535: faxmail_server_put_buffer: buffer_info == BUFF_END_OF_PART *Jan 1 17:57:25.535: Returned buffer length: 624 (mime == text) *Jan 1 17:57:25.535: Got a page with only returns and newline's - setting buffer_length=0 *Jan 1 17:57:25.535: faxmail_server_put_buffer: buffer_info == BUFF_END_OF_PART *Jan 1 17:57:25.535: [] *Jan 1 17:57:25.535: Calling text2fax_data_handler - TEXT_BODY_PAGE *Jan 1 17:57:25.535: Returned buffer length: 1548 (mime != text) *Jan 1 17:57:25.539: Returned buffer length: 1548 (mime != text) *Jan 1 17:57:25.547: Returned buffer length: 1548 (mime != text) *Jan 1 17:57:25.551: Returned buffer length: 1548 (mime != text) *Jan 1 17:57:25.555: faxmail_server_put_buffer: buffer_info == BUFF_END_OF_PART *Jan 1 17:57:25.555: Returned buffer length: 624 (mime == text) *Jan 1 17:57:25.555: faxmail_server_put_buffer: buffer_info == BUFF_LAST *Jan 1 17:57:25.555: [] *Jan 1 17:57:25.555: Calling text2fax_data_handler - TEXT_BODY_PAGE *Jan 1 17:57:25.555: Stopping smtp from receiving data, fax_payload->body_pages 2, body_page_number_sent 0 *Jan 1 17:57:25.555: All reserved modems have been previous dialed.
In the following output, the receiving fax machine answers the call from the off-ramp gateway.
17:57:38: %FTSP-6-FAX_CONNECT: Transmission
The following output shows that the transmission is complete.
17:58:03: %FTSP-6-FAX_DISCONNECT: Transmission *Jan 1 17:58:01.619: Entering faxmail_server_fap_done(f_rec: 616EB70C, fmode: 5)faxmail_server_fap_done: status: 23, num_pages: 2 17:58:03: %LINK-3-UPDOWN: Interface Serial1:0, changed state to down *Jan 1 17:58:10.559: ensp_do_call_history: disc cause=16, normal call clearing. *Jan 1 17:58:10.559: Remove fax_record from Q..., frec 616EB70C *Jan 1 17:58:10.559: delete_f_rec(): calling free() *Jan 1 17:58:10.559: fax_record 616EB70C is deleted *Jan 1 17:58:10.559: Entering faxmail_server_dispose_context (to delete fax_payload: 0x612B4B40) *Jan 1 17:58:10.559: delete_f_rec(): calling free() *Jan 1 17:58:10.559: delete_fax_payload: fax_payload freed !!!
| Command | Description |
debug fmail client | Displays e-mail parameters (such as Mail from and Envelope to and Envelope from) as well as the progress of the SMTP client. |
Use the debug mmoip aaa EXEC command to display output relating to AAA services with Store and Forward Fax. Use the no form of this command to disable debugging output.
[no] debug mmoip aaaThis command has no arguments or keywords.
Disabled
| Release | Modification |
|---|---|
12.0(4)T | This command was introduced. |
The following output shows how the debug mmoip aaa command provides information about AAA on-ramp or off-ramp authentication:
router# debug mmoip aaa 5d10h:fax_aaa_begin_authentication:User-Name = mmoip-b.cisco.com 5d10h:fax_aaa_begin_authentication:fax_account_id_origin = GATEWAY_ID 5d10h:fax_aaa_end_authentication_callback:Authentication successful
The following output shows how the debug mmoip aaa command provides information about AAA off-ramp accounting:
router# debug mmoip aaa 5d10h:fax_aaa_start_accounting:User-Name = mmoip-b.cisco.com 5d10h:fax_aaa_start_accounting:Calling-Station-Id = gmercuri@mail-server.cisco.com 5d10h:fax_aaa_start_accounting:Called-Station-Id = fax=571-0839@mmoip-b.cisco.com 5d10h:fax_aaa_start_accounting:fax_account_id_origin = GATEWAY_ID mmoip-b#ax_aaa_start_accounting:fax_msg_id = <37117AF3.3D98300E@mail-server.cisco.com> 5d10h:fax_aaa_start_accounting:fax_pages = 2 5d10h:fax_aaa_start_accounting:fax_coverpage_flag = TRUE 5d10h:fax_aaa_start_accounting:fax_modem_time = 26/32 5d10h:fax_aaa_start_accounting:fax_connect_speed = 14400bps 5d10h:fax_aaa_start_accounting:fax_recipient_count = 1 5d10h:fax_aaa_start_accounting:fax_auth_status = USER SUCCESS 5d10h:fax_aaa_start_accounting:gateway_id = mmoip-b.cisco.com 5d10h:fax_aaa_start_accounting:call_type = Fax Send 5d10h:fax_aaa_start_accounting:port_used = slot:0 modem port:0 5d10h:fax_aaa_do_offramp_accounting tty(6), Stopping accounting 5d10h:fax_aaa_stop_accounting:ftdb->cact->generic.callActiveTransmitBytes = 18038 5d10h:fax_aaa_stop_accounting:ftdb->cact->generic.callActiveTransmitPackets = 14
The following output shows how the debug mmoip aaa command provides information about AAA on-ramp accounting:
router# debug mmoip aaa 5d10h:fax_aaa_start_accounting:User-Name = mmoip-b.cisco.com 5d10h:fax_aaa_start_accounting:Calling-Station-Id = FAX=408@mail-from-hostname.com 5d10h:fax_aaa_start_accounting:Called-Station-Id = FAX=5710839@mail-server.cisco.com 5d10h:fax_aaa_start_accounting:fax_account_id_origin = GATEWAY_ID 5d10h:fax_aaa_start_accounting:fax_msg_id = 00391997233216263@mmoip-b.cisco.com 5d10h:fax_aaa_start_accounting:fax_pages = 2 5d10h:fax_aaa_start_accounting:fax_modem_time = 22/32 5d10h:fax_aaa_start_accounting:fax_connect_speed = 14400bps 5d10h:fax_aaa_start_accounting:fax_auth_status = USER SUCCESS 5d10h:fax_aaa_start_accounting:email_server_address = 1.14.116.1 5d10h:fax_aaa_start_accounting:email_server_ack_flag = TRUE 5d10h:fax_aaa_start_accounting:gateway_id = mmoip-b.cisco.com 5d10h:fax_aaa_start_accounting:call_type = Fax Receive 5d10h:fax_aaa_start_accounting:port_used = Cisco Powered Fax System slot:1 port:4 5d10h:fax_aaa_do_onramp_accounting tty(5), Stopping accounting 5d10h:fax_aaa_stop_accounting:endb->cact->generic.callActiveTransmitBytes = 26687 5d10h:fax_aaa_stop_accounting:ftdb->cact->generic.callActiveReceiveBytes = 18558 5d10h:fax_aaa_stop_accounting:ftdb->cact->generic.callActiveReceivePackets = 14
Use the debug mmoip send email EXEC command to test connectivity between the on-ramp gateway and the e-mail server by sending a test e-mail to a specified e-mail address. Use the no form of this command to disable debugging output.
[no] debug mmoip send email {string}
string | Specifies the e-mail address of the sender; for example, george@mail-server.com. |
Disabled
| Release | Modification |
|---|---|
12.0(4)T | This command was introduced. |
The debug mmoip send email command is used to test connectivity between the on-ramp gateway and the e-mail server. Basically, this debug command sends an e-mail message to the recipient specified in the e-mail address string. There is no specific output associated with the debug mmoip send email command; to see how the on-ramp gateway and e-mail server interact when processing the test e-mail message, enable the debug fmail client command.
The following example tests connectivity between the on-ramp gateway and the e-mail server by sending a test e-mail message to ilya@mail-server.com.
router# debug fmail client router# debug mmoip send email ilya@mail-server.com router# 01:22:59:faxmail_client_send_test:Sending the test message to ilya@mail-server.com from testing@mmoip-a.cisco.com... 01:22:59:faxmail_client_send_test:Opening client engine. 01:22:59:faxmail_client_send_test:Sending 59 bytes ... 01:22:59:faxmail_client_send_test:Done sending test email.
Use the debug mmoip send fax EXEC command to send an off-ramp test fax. Use the no form of this command to disable debugging output.
[no] debug mmoip send fax{string}
string | Specifies the E.164 telephone number to be used for sending the test fax. |
Disabled
| Release | Modification |
|---|---|
12.0(4)T | This command was introduced. |
The debug mmoip send fax command is used to test connectivity between the off-ramp gateway and a recipient fax device. Basically, this debug command sends a test fax transmission to the recipient specified in the telephone number string. There is no specific output associated with the debug mmoip send fax command; to see how the off-ramp gateway and fax device interact when processing the test fax, enable the debug fax send all command.
The following example sends a test fax message to the telephone number 5550839:
router# debug fax send all router# debug mmoip send fax 5550839
The following output shows that the off-ramp gateway is placing a fax call.
01:28:18:ftsp_offramp_match_digits:phone number to translate:5550839 01:28:18: destPat(5......), matched(1), prefix() peer_tag(1) 01:28:18:ftsp_offramp_match_digits:target:710839 01:28:18:fap_offcm:tty(4), Got dial message00:00:00.000:AT&F\Q0S7=255
Class 2 modem tracing begins, including modem initialization.
00:00:00.008:AA 00:00:00.068:TT 00:00:00.128:&F\Q0S7=255 00:00:00.128: OK 00:00:00.128:E0V1 00:00:00.140:ATE0 OK 00:00:00.140:AT+FCLASS=2 00:00:00.148: OK 00:00:00.148:+FDCC=..;+FBOR= 00:00:00.168:AT+FLID 00:00:00.180: OK 00:00:00.180:ATDTW710839
The following output shows that the fax transmission is complete; in this particular example, there was a transmission error, and the modem timed out.
01:28:25:ftsp_setup_for_oc:tty4, callid=0xA 01:28:25:ftsp_setup_for_oc ctl=0, cas grp=-1, snmp_ix=30 01:28:25:ftsp_off_ramp_active_call_init tty4 callid=0xA, snmp_ix=30 01:29:18:fap_offpmt:tty(4), TxPhaseA:modem timeout 01:29:18:%FTSP-6-FAX_DISCONNECT:Transmission error
Use the debug mmoip transfer EXEC command to send output of the TIFF writer to a TFTP server. Use the no form of this command to disable debugging output.
[no] debug mmoip transfer {prefix-filename tftp-server-name}
prefix-filename | Specifies the name of the TIFF file. The format for the TIFF file name is "telephone-number.TIFF." |
tftp-server-name | Identifies the TFTP server to which the output from the TIFF writer is sent. |
Disabled
| Release | Modification |
|---|---|
12.0(4)T | This command was introduced. |
The debug mmoip transfer sends the content of the fax data received to the TFTP server named by the tftp-server-name variable into the file identified by the prefix-filename variable. Each page of the fax transmission is a separate file, designated by the letter p, followed by the page number.
For example, the following command transfers the received fax content to a TFTP server named keyer. The first page of the transmission goes to the file /tftpboot/test/testp1.tiff, the second page goes to the file named /tftpboot/test/testp2.tiff and so on.
router# debug mmoip transfer /tftpboot/test/test keyer
The named files must exist on the TFTP server and be writable for the debug operation to be successful.
Use the debug mta receive all EXEC command to show output relating to the activity on the SMTP server. Use the no form of this command to disable debugging output.
[no] debug mta receive allThis command has no arguments or keywords.
Disabled
| Release | Modification |
|---|---|
12.0(4)T | This command was introduced. |
The following example shows the messages exchanged (for example, the handshake) between the e-mail server and the off-ramp gateway.
router# debug mta receive all #R: 'Received: from win98pc2 (win98pc2.allegro.com [14.0.0.11]) by nt4server.allegro.com with SMTP (Microsoft Exchange Internet Mail Service Version 5.5.1960.3)' R: ' id C321SPKM; Thu, 7 Jan 1999 11:51:32 -0800' R: 'Message-ID: <00ff01be3a76$be0c9480$0b00000e@win98pc2.allegro.com>' R: 'From: "test" <test@nt4server.allegro.com>' R: 'To: <fax=5763413@allegrouut1.allegro.com>' R: 'Subject: test for debug.....' R: 'Date: Thu, 7 Jan 1999 11:48:47 -0800' R: 'MIME-Version: 1.0' R: 'Content-Type: multipart/alternative;' R: ' boundary="----=_NextPart_000_00FC_01BE3A33.AFB6F9E0"' R: 'X-Priority: 3' R: 'X-MSMail-Priority: Normal' R: 'X-Mailer: Microsoft Outlook Express 4.72.3110.1' R: 'X-MimeOLE: Produced By Microsoft MimeOLE V4.72.3110.3' R: '' R: 'This is a multi-part message in MIME format.' Unrecognized/handled MIME content type rejectedR: '' R: '------=_NextPart_000_00FC_01BE3A33.AFB6F9E0' R: 'Content-Type: text/plain;' R: ' charset="iso-8859-1"'
The following output specifies the encoding type.
R: 'Content-Transfer-Encoding: quoted-printable' R: '' R: 'test for debug......'
The following output shows the transmission of the encoded text data.
R: 'HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH' R: 'HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH' R: 'HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH' R: 'HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH' R: 'HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH' R: 'HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH' R: 'HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH' R: 'HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH' R: 'HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH' R: 'HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH' R: 'HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH' R: 'HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH' R: 'HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH' R: 'HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH' R: 'HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH' R: 'HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH' R: '' R: '------=_NextPart_000_00FC_01BE3A33.AFB6F9E0' R: 'Content-Type: text/html;' R: ' charset="iso-8859-1"' R: 'Content-Transfer-Encoding: quoted-printable'
The following output shows the transmission of the HTML encoded data.
R: '' R: '<!DOCTYPE HTML PUBLIC "-//W3C//DTD W3 HTML//EN">' Unrecognized/handled MIME content type rejectedR: '<HTML>' R: '<HEAD>' R: '' R: '<META content=3Dtext/html;charset=3Diso-8859-1 =' R: 'http-equiv=3DContent-Type>' R: '<META content=3D'"MSHTML 4.72.3110.7"' name=3DGENERATOR>' R: '</HEAD>' R: '<BODY bgColor=3D#ffffff>' R: '<DIV><FONT color=3D#000000 size=3D2>test for debug......</FONT></DIV>' R: '<DIV><FONT color=3D#000000=20' R: 'size=3D2>HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH=' R: '</FONT></DIV>' R: '<DIV><FONT color=3D#000000=20' R: 'size=3D2>HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH=' R: '</FONT></DIV>' R: '<DIV><FONT color=3D#000000 size=3D2>' R: '<DIV><FONT color=3D#000000=20' R: 'size=3D2>HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH=' R: '</FONT></DIV>' R: '<DIV><FONT color=3D#000000=20' R: 'size=3D2>HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH=' R: '</FONT></DIV>' R: '<DIV><FONT color=3D#000000 size=3D2>' R: '<DIV><FONT color=3D#000000=20' R: 'size=3D2>HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH=' R: '</FONT></DIV>' R: '<DIV><FONT color=3D#000000=20' R: 'size=3D2>HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH=' R: '</FONT></DIV>' R: '<DIV><FONT color=3D#000000 size=3D2>' R: '<DIV><FONT color=3D#000000=20' R: 'size=3D2>HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH=' R: '</FONT></DIV>' R: '<DIV><FONT color=3D#000000=20' R: 'size=3D2>HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH=' R: '</FONT></DIV>' R: '<DIV><FONT color=3D#000000 size=3D2>' R: '<DIV><FONT color=3D#000000=20' R: 'size=3D2>HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH=' R: '</FONT></DIV>' R: '<DIV><FONT color=3D#000000=20' R: 'size=3D2>HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH=' R: '</FONT></DIV>' R: '<DIV><FONT color=3D#000000 size=3D2>' R: '<DIV><FONT color=3D#000000=20' R: 'size=3D2>HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH=' R: '</FONT></DIV>' R: '<DIV><FONT color=3D#000000=20' R: 'size=3D2>HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH=' R: '</FONT></DIV>' R: '<DIV><FONT color=3D#000000 size=3D2>' R: '<DIV><FONT color=3D#000000=20' R: 'size=3D2>HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH=' R: '</FONT></DIV>' R: '<DIV><FONT color=3D#000000=20' R: 'size=3D2>HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH=' R: '</FONT></DIV>' R: '<DIV><FONT color=3D#000000 size=3D2>' R: '<DIV><FONT color=3D#000000=20' R: 'size=3D2>HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH=' R: '</FONT></DIV>' R: '<DIV><FONT color=3D#000000=20' R: 'size=3D2>HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH=' R: '</FONT></DIV></FONT></DIV></FONT></DIV></FONT></DIV></FONT></DIV></FONT><=' R: '/DIV></FONT></DIV></FONT></DIV></BODY></HTML>' R: '' R: '------=_NextPart_000_00FC_01BE3A33.AFB6F9E0--' R: ''
The following output shows that the transmission is complete.
R: '.' Found the terminating Dot!
| Command | Description |
debug mta send all | Displays output for all of the on-ramp client connections. |
Use the debug mta send all EXEC command to display output for all of the on-ramp client connections. Use the no form of this command to disable debugging output.
[no] debug mta send allThis command has no arguments or keywords.
Disabled
| Release | Modification |
|---|---|
12.0(4)T | This command was introduced. |
This display shows the messages exchanged (for example, the handshake) between the e-mail server and the on-ramp gateway.
router# debug mta send all All email send debugging is on router#
The following output shows that the calling party is connected to the on-ramp router. R specifies the information received from the mail server. S specifies the messages sent from the on-ramp gateway to the mail server.
1d19h: %FTSP-6-FAX_CONNECT: Receptionsocket 0 attempting to connect to IP address 14.0.0.1 socket 0 readable for first time - let's try to read it R: 220 nt4server.allegro.com ESMTP Server (Microsoft Exchange Internet Mail Service 5.5.1960.3) ready S: EHLO allegrouut1.allegro.com R: 250-nt4server.allegro.com supports the following extensions: R: 250-XEXCH50 R: 250-HELP R: 250-ETRN R: 250-DSN R: 250-SIZE 0 R: 250-AUTH=LOGIN R: 250 TLS S: MAIL FROM:<FAX=4085763414@allegrouut1.allegro.com> RET=HDRS R: 250 OK - mail from <FAX=4085763414@allegrouut1.allegro.com> S: RCPT TO:<test@nt4server.allegro.com> NOTIFY=SUCCESS,FAILURE ORCPT=rfc822;FAX+3D4085763414@allegrouut1.allegro.com R: 250 OK - Recipient <test@nt4server.allegro.com> R: 354 Send data. End with CRLF.CRLF S: Received: (originator..... slot:1 port:16) by allegrouut1.allegro.com for <test@nt4server.allegro.com> (with Cisco NetWorks); Sun, 02 Jan 2000 19:30:56 +0000 S: To: "14085710847" <test@nt4server.allegro.com> S: Message-ID: <00152000193056665@allegrouut1.allegro.com> S: Date: Sun, 02 Jan 2000 19:30:56 +0000 S: Subject: onramp test S: X-Mailer: IOS (tm) 5300 Software (C5300-IS-M) S: MIME-Version: 1.0 S: Content-Type: multipart/mixed; S: boundary="yradnuoB=_00142000193054321.allegrouut1allegro.com" 1d19h: %FTSP-6-FAX_DISCONNECT: ReceptionS: From: "+31 703712194" <FAX=4085763414@allegrouut1.allegro.com> S: X-Account-Id: null S: --yradnuoB=_00142000193054321.allegrouut1allegro.com S: Content-ID: <00162000193129665@allegrouut1.allegro.com> S: Content-Type: image/tiff; application=faxbw S: Content-Transfer-Encoding: base64 writing lingering data for socket 0 writing lingering data for socket 0 writing lingering data for socket 0 writing lingering data for socket 0 writing lingering data for socket 0 writing lingering data for socket 0 writing lingering data for socket 0 writing lingering data for socket 0 1d19h: %LINK-3-UPDOWN: Interface Serial1:0, changed state to downwriting lingering data for socket 0 S: --yradnuoB=_00142000193054321.allegrouut1allegro.com-- Sending terminating dot ...(socket=0) S: . R: 250 OK S: QUIT
The following output shows that the fax transmission is complete.
R: 221 closing connection Freeing SMTP ctx at 0x613C8620 returned from work_routine, context freed
| Command | Description |
debug mta receive all | Display output for all of the off-ramp client connections. |
debug mta send rcpt-to | Display output for a specific on-ramp SMTP client connection during an e-mail transmission. |
Use the debug mta send rcpt-to EXEC command to display output for a specific on-ramp SMTP client connection during an e-mail transmission. Use the no form of this command to disable debugging output.
[no] debug mta send rcpt-to{string}
string | Specifies the e-mail address. |
Disabled
| Release | Modification |
|---|---|
12.0(4)T | This command was introduced. |
The following example shows debugging information displayed when the debug mmoip send email command has been enabled and the SMTP client is sending an e-mail message.
router# debug mta send all All email send debugging is on router# debug mmoip send email ilyau@company.com router# socket 0 attempting to connect to IP address 172.69.95.82 socket 0 readable for first time - let's try to read it R:220 quisp.cisco.com ESMTP Sendmail 8.8.4-Cisco.1/8.6.5 ready at Tue, 6 Apr 1999 13:35:39 -0700 (PDT) S:EHLO mmoip-c.cisco.com R:250-quisp.cisco.com Hello [172.22.95.16], pleased to meet you R:250-EXPN R:250-VERB R:250-8BITMIME R:250-SIZE R:250-DSN R:250-ETRN R:250-XUSR R:250 HELP S:MAIL FROM:<testing@> RET=HDRS R:250 <testing@>... Sender ok S:RCPT TO:<ilyau@cisco.com> NOTIFY=SUCCESS ORCPT=rfc822;testing@ R:250 <ilyau@cisco.com>... Recipient ok R:354 Enter mail, end with "." on a line by itself S:Received:(Cisco Powered Fax System) by mmoip-c.cisco.com for <ilyau@cisco.com> (with Cisco NetWorks); Fri, 17 Oct 1997 14:54:27 +0800 S:To: <ilyau@cisco.com> S:Message-ID:<000F1997145427146@mmoip-c.cisco.com> S:Date:Fri, 17 Oct 1997 14:54:27 +0800 S:Subject:mmoip-c subject here S:X-Mailer:IOS (tm) 5300 Software (C5300-IS-M) S:MIME-Version:1.0 S:Content-Type:multipart/mixed; S: boundary="yradnuoB=_000E1997145426826.mmoip-ccisco.com" S:From:"Test User" <testing@> S:--yradnuoB=_000E1997145426826.mmoip-ccisco.com S:Content-ID:<00101997145427150@mmoip-c.cisco.com> S:--yradnuoB=_000E1997145426826.mmoip-ccisco.com-- Sending terminating dot ...(socket=0) S:. R:250 NAA09092 Message accepted for delivery S:QUIT R:221 quisp.cisco.com closing connection Freeing SMTP ctx at 0x6121D454 returned from work_routine, context freed
| Command | Description |
debug mta send all | Displays output for all of the on-ramp client connections. |
Use the debug text-to-fax EXEC command to show information relating to the off-ramp text-to-fax conversion. Use the no form of this command to disable debugging output.
[no] debug text-to-faxThis command has no arguments or keywords.
Disabled
| Release | Modification |
|---|---|
12.0(4)T | This command was introduced. |
The following debug output shows the off-ramp text-to-fax conversion.
router# debug text-to-fax Text to fax debugging is on router#6d03h: text2fax_data_handler: START_OF_CONNECTION 6d03h: text2fax_data_handler: new_context 6d03h: text2fax_data_handler: resolution: fine 6d03h: text2fax_data_handler: buffer size: 50 6d03h: text2fax_put_buffer: START_OF_FAX_PAGE 6d03h: text2fax_put_buffer: START_OF_FAX_PAGE 6d03h: text2fax_put_buffer: END_OF_FAX_PAGE. Dial now ...if not in progress 6d03h: text2fax_data_handler: START_OF_DATA 6d03h: text2fax_data_handler: END_OF_DATA 6d03h: text2fax_data_handler: Dispose context 6d03h: text2fax_data_handler: START_OF_CONNECTION 6d03h: text2fax_data_handler: END_OF_CONNECTION 6d03h: %FTSP-6-FAX_CONNECT: Transmission 6d03h: %FTSP-6-FAX_DISCONNECT: Transmission 6d03h: %LINK-3-UPDOWN: Interface Serial1:22, changed state to down
Use the debug tiff reader EXEC command to display output about the off-ramp TIFF reader. Use the no form of this command to disable debugging output.
[no] debug tiff-readerThis command has no arguments or keywords.
Disabled
| Release | Modification |
|---|---|
12.0(4)T | This command was introduced. |
The following debug example displays information about the off-ramp TIFF reader.
router# debug tiff reader *Jan 1 18:59:13.683: tiff_reader_data_handler: new context *Jan 1 18:59:13.683: tiff_reader_data_handler: resolution: standard *Jan 1 18:59:13.683: tiff_reader_data_handler: buffer size: 1524i>> tiff_reader_engine() ENGINE_START/DONE gggg(pl 616E9994) *Jan 1 18:59:13.691: tiff_reader_data_handler: buffer size: 1524 *Jan 1 18:59:13.699: tiff_reader_data_handler: buffer size: 1524i>> tiff_reader_engine() case FAX_EBUFFER pppp(pl 616E9994) *Jan 1 18:59:13.703: tiff_reader_put_buffer: START_OF_FAX_PAGEi>> tiff_reader_engine() case FAX_EBUFFER gggg *Jan 1 18:59:13.711: tiff_reader_data_handler: buffer size: 1524 *Jan 1 18:59:13.719: tiff_reader_data_handler: buffer size: 1524i>> tiff_reader_engine() case FAX_EBUFFER pppp(pl 616E9994) i>> tiff_reader_engine() case FAX_EBUFFER gggg *Jan 1 18:59:13.727: tiff_reader_data_handler: buffer size: 1524i>> tiff_reader_engine() case FAX_EBUFFER pppp(pl 616E9994) i>> tiff_reader_engine() case FAX_EBUFFER gggg *Jan 1 18:59:13.735: tiff_reader_data_handler: buffer size: 1524 *Jan 1 18:59:13.743: tiff_reader_data_handler: buffer size: 1524i>> tiff_reader_engine() case FAX_EBUFFER pppp(pl 616E9994) i>> tiff_reader_engine() case FAX_EBUFFER gggg *Jan 1 18:59:13.751: tiff_reader_data_handler: buffer size: 1524 *Jan 1 18:59:13.759: tiff_reader_data_handler: buffer size: 1524i>> tiff_reader_engine() case FAX_EBUFFER pppp(pl 616E9994) i>> tiff_reader_engine() case FAX_EBUFFER gggg *Jan 1 18:59:13.767: tiff_reader_data_handler: buffer size: 1524 *Jan 1 18:59:13.775: tiff_reader_data_handler: buffer size: 1524i>> tiff_reader_engine() case FAX_EBUFFER pppp(pl 616E9994) i>> tiff_reader_engine() case FAX_EBUFFER gggg *Jan 1 18:59:13.787: tiff_reader_data_handler: buffer size: 1524 *Jan 1 18:59:13.795: tiff_reader_data_handler: buffer size: 1524i>> tiff_reader_engine() case FAX_EBUFFER pppp(pl 616E9994) i>> tiff_reader_engine() case FAX_EBUFFER gggg *Jan 1 18:59:13.803: tiff_reader_data_handler: buffer size: 1524 *Jan 1 18:59:13.811: tiff_reader_data_handler: buffer size: 1524i>> tiff_reader_engine() case FAX_EBUFFER pppp(pl 616E9994) i>> tiff_reader_engine() case FAX_EBUFFER gggg *Jan 1 18:59:13.819: tiff_reader_data_handler: buffer size: 1524 *Jan 1 18:59:13.827: tiff_reader_data_handler: buffer size: 1524i>> tiff_reader_engine() case FAX_EBUFFER pppp(pl 616E9994) i>> tiff_reader_engine() case FAX_EBUFFER gggg *Jan 1 18:59:13.835: tiff_reader_data_handler: buffer size: 1524 *Jan 1 18:59:13.843: tiff_reader_data_handler: buffer size: 1524i>> tiff_reader_engine() case FAX_EBUFFER pppp(pl 616E9994) i>> tiff_reader_engine() case FAX_EBUFFER gggg *Jan 1 18:59:13.851: tiff_reader_data_handler: buffer size: 1524i>> tiff_reader_engine() case FAX_EBUFFER pppp(pl 616E9994) i>> tiff_reader_engine() case FAX_EBUFFER gggg *Jan 1 18:59:13.863: tiff_reader_data_handler: buffer size: 1524 *Jan 1 18:59:13.871: tiff_reader_data_handler: buffer size: 1524i>> tiff_reader_engine() case FAX_EBUFFER pppp(pl 616E9994) i>> tiff_reader_engine() case FAX_EBUFFER gggg *Jan 1 18:59:13.879: tiff_reader_data_handler: buffer size: 1524 *Jan 1 18:59:13.887: tiff_reader_data_handler: buffer size: 1524i>> tiff_reader_engine() case FAX_EBUFFER pppp(pl 616E9994) i>> tiff_reader_engine() case FAX_EBUFFER gggg *Jan 1 18:59:13.895: tiff_reader_data_handler: buffer size: 1524 *Jan 1 18:59:13.903: tiff_reader_data_handler: buffer size: 1524i>> tiff_reader_engine() case FAX_EBUFFER pppp(pl 616E9994) i>> tiff_reader_engine() case FAX_EBUFFER gggg *Jan 1 18:59:13.907: tiff_reader_data_handler: buffer size: 311i>> tiff_r_finish() END_OF_FAX_PAGE pppp *Jan 1 18:59:13.907: tiff_reader_put_buffer: END_OF_FAX_PAGE. Dial now ...if not in progress *Jan 1 18:59:13.907: tiff_reader_data_handler: END_OF_DATA *Jan 1 18:59:13.907: tiff_reader_data_handler: BUFF_END_OF_PART *Jan 1 18:59:13.907: tiff_reader_data_handler: Dispose context
| Command | Description |
debug tiff writer | Displays output about the on-ramp TIFF writer. |
Use the debug tiff writer EXEC command to display output about the on-ramp TIFF writer. Use the no form of this command to disable debugging output.
[no] debug tiff-writerThis command has no arguments or keywords.
Disabled
| Release | Modification |
|---|---|
12.0(4)T | This command was introduced. |
The following debug example shows information about the off-ramp TIFF writer.
router# debug tiff writer *Jan 1 18:54:59.419: tiff_writer_data_process: START_OF_CONNECTION 18:55:10: %FTSP-6-FAX_CONNECT: Reception *Jan 1 18:55:14.903: tiff_writer_data_process: START_OF_FAX_PAGE *Jan 1 18:55:14.903: tiff_writer_data_process: tiff file created = 2000:01:01 18:55:14 18:55:21: %FTSP-6-FAX_DISCONNECT: Reception *Jan 1 18:55:19.039: tiff_writer_data_process: END_OF_CONNECTION or ABORT_CONNECTION *Jan 1 18:55:19.039: tiff_writer_put_buffer: END_OF_FAX_PAGE *Jan 1 18:55:19.039: send TIFF_PAGE_READY *Jan 1 18:55:19.039: send TIFF_PAGE_READY 18:55:21: %LINK-3-UPDOWN: Interface Serial2:0, changed state to down
| Command | Description |
debug tiff reader | Displays output about the on-ramp TIFF reader. |
Posted: Tue Jul 18 14:58:39 PDT 2000
Copyright 1989-2000©Cisco Systems Inc.