Channelized T3 Support for the Cisco  AS5800

Feature Summary

Platforms

Supported MIBs and RFCs

Configuration Tasks

Configuration Examples

Command Reference

What to Do Next

AS5800-1# show controller t3
T3 1/0/0 is up.
  Applique type is Channelized T3
  No alarms detected.
  FEAC code received: No code is being received
  Framing is M23, Line Code is B3ZS, Clock Source is Line.
  Data in current interval (751 seconds elapsed):
     0 Line Code Violations, 0 P-bit Coding Violation
     0 C-bit Coding Violation, 0 P-bit Err Secs
     0 P-bit Severely Err Secs, 0 Severely Err Framing Secs
     0 Unavailable Secs, 0 Line Errored Secs
     0 C-bit Errored Secs, 0 C-bit Severely Errored Secs
  Total Data (last 16 15 minute intervals):
     0 Line Code Violations, 0 P-bit Coding Violation,
     0 C-bit Coding Violation, 0 P-bit Err Secs,
     0 P-bit Severely Err Secs, 0 Severely Err Framing Secs,
     0 Unavailable Secs, 0 Line Errored Secs,
     0 C-bit Errored Secs, 0 C-bit Severely Errored Secs
 

Note the following:

• To use the controller, it must report being up.

• No errors should be reported.

Syntax Description

Default

None.

Command Mode

EXEC

Usage Guidelines

This command first appeared in Cisco IOS Release 10.0.

The command clear interface serial clears the interface hardware. To reset the counters for an interface, use the clear counters serial command, and confirm at the prompt using the show interface serial command.

Example

The following example clears the interface hardware, disconnecting any active lines:

AS5800-1# clear interface serial 1/4/0:2:23
AS5800-1#

Related Commands

clear counters serial
show interface serial
show interfaces

Syntax Description

Default

None.

Command Mode

Global configuration

Usage Guidelines

This command first appeared in Cisco IOS Release 11.3(5)AA.

Example

The following example configures the T1 controller in shelf 1, slot 0, port 0:

AS5800-1(config)# controller T1 1/0/0
AS5800-1(config-controller)#

Related Commands

show controller t1

Syntax Description

Default

None.

Command Mode

Global configuration

Usage Guidelines

This command first appeared in Cisco IOS Release 11.1CA.

Example

The following example configures the T3 controller in shelf 1, slot 4, port 0:

AS5800-1(config)# controller T3 1/4/0
AS5800-1(config-controller)#

Related Commands

show controller t3

Syntax Description

Default

None.

Command Mode

EXEC

Usage Guidelines

This command first appeared in Cisco IOS Release 11.3(5)AA.

Example

The following example shows the status of the T1 controllers connected to this Cisco AS5800:

AS5800-1# show controller T1
T1 1/0/0:1 is up.
  No alarms detected.
  Framing is ESF, Line Code is AMI, Clock Source is Line.
  Data in current interval (770 seconds elapsed):
     5 Line Code Violations, 8 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 7 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 7 Unavail Secs
  Total Data (last 81 15 minute intervals):
     7 Line Code Violations, 4 Path Code Violations,
     6 Slip Secs, 20 Fr Loss Secs, 2 Line Err Secs, 0 Degraded Mins,
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 2 Unavail Secs
T1 1/0/1:5 is down.
  Transmitter is sending remote alarm.
  Receiver has loss of frame.
  Framing is SF, Line Code is AMI, Clock Source is Line.
  Data in current interval (770 seconds elapsed):
     50 Line Code Violations, 5 Path Code Violations
     0 Slip Secs, 7 Fr Loss Secs, 7 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 7 Unavail Secs
  Total Data (last 81 15 minute intervals):
     27 Line Code Violations, 22 Path Code Violations,
     0 Slip Secs, 13 Fr Loss Secs, 13 Line Err Secs, 0 Degraded Mins,
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 13 Unavail Secs
AS5800-1#

Related Commands

controller t1

Syntax Description

Default

None.

Command Mode

EXEC

Usage Guidelines

This command first appeared in Cisco IOS Release 11.1CA.

Example

The following example shows the summary status of the T3 controller located in shelf 1, slot 4, port 0:

AS5800-1# show controller t3
T3 1/4/0 is up.
  Applique type is Channelized T3
  No alarms detected.
  MDL transmission is disabled
 
  FEAC code received: Multiple DS1 LOS/HBER
  Framing is C-BIT Parity, Line Code is B3ZS, Clock Source is Line.
  Data in current interval (491 seconds elapsed):
     0 Line Code Violations, 0 P-bit Coding Violation
     0 C-bit Coding Violation, 0 P-bit Err Secs
     0 P-bit Severely Err Secs, 0 Severely Err Framing Secs
     0 Unavailable Secs, 0 Line Errored Secs
     0 C-bit Errored Secs, 0 C-bit Severely Errored Secs
  Total Data (last 80 15 minute intervals):
     3 Line Code Violations, 4 P-bit Coding Violation,
     2 C-bit Coding Violation, 0 P-bit Err Secs,
     0 P-bit Severely Err Secs, 0 Severely Err Framing Secs,
     2 Unavailable Secs, 0 Line Errored Secs,
     0 C-bit Errored Secs, 0 C-bit Severely Errored Secs
AS5800-1#

The following example shows the detail status of the T3 controller connected to this Cisco AS5800 in shelf 1, slot 4, port 0. Notice that the detail information shows the last 86 fifteen minute time periods.

AS5800-1# show controller t3 1/4/0
T3 1/4/0 is up.
  Applique type is Channelized T3
  No alarms detected.
  MDL transmission is disabled
 
  FEAC code received: Multiple DS1 LOS/HBER
  Framing is C-BIT Parity, Line Code is B3ZS, Clock Source is Line.
  Data in current interval (91 seconds elapsed):
     0 Line Code Violations, 0 P-bit Coding Violation
     0 C-bit Coding Violation, 0 P-bit Err Secs
     0 P-bit Severely Err Secs, 0 Severely Err Framing Secs
     0 Unavailable Secs, 0 Line Errored Secs
     0 C-bit Errored Secs, 0 C-bit Severely Errored Secs
  Data in Interval 1:
     0 Line Code Violations, 0 P-bit Coding Violation
     0 C-bit Coding Violation, 0 P-bit Err Secs
     0 P-bit Severely Err Secs, 0 Severely Err Framing Secs
     0 Unavailable Secs, 0 Line Errored Secs
     0 C-bit Errored Secs, 0 C-bit Severely Errored Secs
  Data in Interval 2:
     0 Line Code Violations, 0 P-bit Coding Violation
     0 C-bit Coding Violation, 0 P-bit Err Secs
     0 P-bit Severely Err Secs, 0 Severely Err Framing Secs
     0 Unavailable Secs, 0 Line Errored Secs
     0 C-bit Errored Secs, 0 C-bit Severely Errored Secs
  Data in Interval 3:
     0 Line Code Violations, 0 P-bit Coding Violation
     0 C-bit Coding Violation, 0 P-bit Err Secs
     0 P-bit Severely Err Secs, 0 Severely Err Framing Secs
     0 Unavailable Secs, 0 Line Errored Secs
     0 C-bit Errored Secs, 0 C-bit Severely Errored Secs
  Data in Interval 4:
     0 Line Code Violations, 0 P-bit Coding Violation
     0 C-bit Coding Violation, 0 P-bit Err Secs
     0 P-bit Severely Err Secs, 0 Severely Err Framing Secs
     0 Unavailable Secs, 0 Line Errored Secs
     0 C-bit Errored Secs, 0 C-bit Severely Errored Secs
.
.
.
  Data in Interval 86:
     3 Line Code Violations, 4 P-bit Coding Violation
     2 C-bit Coding Violation, 0 P-bit Err Secs
     0 P-bit Severely Err Secs, 0 Severely Err Framing Secs
     2 Unavailable Secs, 0 Line Errored Secs
     0 C-bit Errored Secs, 0 C-bit Severely Errored Secs
  Total Data (last 86 15 minute intervals):
     3 Line Code Violations, 4 P-bit Coding Violation,
     2 C-bit Coding Violation, 0 P-bit Err Secs,
     0 P-bit Severely Err Secs, 0 Severely Err Framing Secs,
     2 Unavailable Secs, 0 Line Errored Secs,
     0 C-bit Errored Secs, 0 C-bit Severely Errored Secs
AS5800-1#

Related Commands

controller t3

Syntax Description

Default

None.

Command Mode

EXEC

Usage Guidelines

This command first appeared in Cisco IOS Release 10.0.

Example

The following example shows the activity that has occurred on the serial interface in shelf 1, slot 4, port 0 for timeslot 2 in group 23:

AS5800-1# show interface serial 1/4/0:2:23
Serial1/4/0:2:23 is up, line protocol is up (spoofing)
  Hardware is DS-T1
  MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec, rely 255/255, load 1/255
  Encapsulation HDLC, loopback not set
  Last input 00:00:01, output 00:00:01, output hang never
  Last clearing of "show interface" counters 22:24:30
  Queueing strategy: fifo
  Output queue 0/40, 0 drops; input queue 0/75, 0 drops
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     5274 packets input, 20122 bytes, 0 no buffer
     Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
     5274 packets output, 30836 bytes, 0 underruns
     0 output errors, 0 collisions, 0 interface resets
     0 output buffer failures, 0 output buffers swapped out
     2 carrier transitions no alarm present
  Timeslot(s) Used:24, subrate: 64Kb/s, transmit delay is 0 flags
AS5800-1#

Related Commands

clear interface serial

Syntax Description

Default

None.

Command Mode

Controller configuration

Usage Guidelines

This command first appeared in Cisco IOS Release 11.3(5)AA.

The purpose of this command is to convert the collection of the 28 T1 controllers that comprise the T3 controller into individual T1 controllers that the system can use. In other words, the Cisco  AS5800 cannot pass data until a T1 controller is configured (using the controller t1 command), and you can't configure a T1 controller until it has been created using the t1 command.

Example

The following example configures a logical T1 controller at T1 timeslot 1 for the T3 controller located in shelf 1, slot 4, port 0. Note that you have to issue the command from the controller configuration mode.

AS5800-1(config)# controller t3 1/4/0
AS5800-1(config-controller)# t1 1 controller
AS5800-1(config-controller)# end
AS5800-1#

Related Commands

controller t1
controller t3