|
|
The following sections are provided:
Continuity testing reduces the call failure rate by detecting failed DS0s (B channels) on the NAS before setting up a call. Calls can be circuit switched data calls or analog modem calls. Because the Cisco Signaling Controller SC2200 does not directly control the bearer channels on an access server, the access server must perform the loopbacks and tone generation or tone detection required for continuity testing.
Continuity testing is required for North American SS7 compliance.
COT---Continuity testing. Used to test individual DS0 channels before establishing a call.
NI2---National ISDN-2 local switch type. This switch type was enhanced to support continuity testing for Public Switched Telephone Network (PSTN) originated calls.
ITU-based networks use only the loopback method for continuity testing. However, ANSI networks may use the tone generation, tone detection, or loopback methods. Only the loopback method is supported for Cisco's first release of COT.
Release 1 of COT supports dial-in calls. Dial-out calls are supported in the second release.
The following hardware platforms support this feature:
The GR---246-CORE MIB is supported.
Perform the following tasks to fully configure a D-channel interface then set up continuity testing:
Each of Cisco's NASs use different interface and slot numbering schemes. For example, the first D channel on a Cisco AS5800 T1 configuration is specified using the interface serial 1/0/0:23 command. For a Cisco AS5300 and Cisco AS5200, the interface serial 0:23 command is used.
| Step | Command | Purpose | ||
|---|---|---|---|---|
| | Specify a D-channel serial interface. Replace the number argument with a controller number followed by a colon (:) and D-channel number. For example, a Cisco AS5300 T1 configuration can have either 0:23, 1:23, 2:23, or 3:23. A Cisco AS5300 E1 configuration can have either 0:15, 1:15, 2:15, or 3:15. | ||
| | Define the interesting packets that reset the idle timer and activate ISDN connections. Interesting packets meet the criteria specified by the dialer-list command (for example, dialer-list 1 protocol ip permit). Replace the dialer group's number argument with the same number used by the dialer-list command. | ||
| | Assign the D channel an unnumbered address, which conserves IP address space. | ||
| | Enable PPP encapsulation over HDLC, which is for CHAP and PAP authentication. | ||
| | Disable IP mroute cache. | ||
| | Configure all incoming voice calls to go to the modems. | ||
| | Assign a common IP address pool to the interface. Individual remote PCs not connected to a LAN dynamically receive their IP addresses from this pool. Replace the name variable with a name for the pool. Local IP pools are configured with the ip local pool name address global configuration command. | ||
| | Enable CHAP and PAP authentication on the interface. | ||
| | Enable PPP multilink. | ||
| | Disable fair queuing. |
To verify a D-channel T1 configuration:
Router# show interface 1:23
Serial1:23 is up, line protocol is up
Hardware is DSX1
Interface is unnumbered. Using address of FastEthernet0 (15.0.0.60)
MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec, rely 255/255, load 1/255
Encapsulation PPP, loopback not set
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Queueing strategy: fifo
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
54 packets input, 214 bytes, 0 no buffer
Received 0 broadcasts, 10 runts, 0 giants, 0 throttles
10 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
53 packets output, 211 bytes, 0 underruns
0 output errors, 0 collisions, 10 interface resets
0 output buffer failures, 0 output buffers swapped out
1 carrier transitions
Timeslot(s) Used:24, Transmitter delay is 0 flags
If you are having trouble:
Router(config)# show interface serial 0:23
Serial0:23 is up, line protocol is up
Hardware is DSX1
Internet address is 61.0.0.2/8
MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec, rely 255/255, load 1/255
Encapsulation PPP, loopback not set
Last input 00:00:02, output 00:00:02, output hang never
Last clearing of "show interface" counters never
Queueing strategy: fifo
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
6442 packets input, 25855 bytes, 0 no buffer
Received 0 broadcasts, 8 runts, 0 giants, 0 throttles
8 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
6439 packets output, 25875 bytes, 0 underruns
0 output errors, 0 collisions, 8 interface resets
0 output buffer failures, 0 output buffers swapped out
1 carrier trnsitions
Timeslot(s) Used:24, Transmitter delay is 0 flags
Router#debug dialerPRI0: Dialing cause: PRI0: ip PERMITPRI0: No dialer string defined. Dialing cannot occur..PRI0: Dialing cause: PRI0: ip PERMIT
| Message | Description |
|---|---|
| Displayed when a packet is received that should cause a call to be placed. However, there is no dialer string configured, so dialing cannot occur. This message usually indicates a configuration problem. Re-enter the dialer-group command in Step 2 in the "Configure" section. |
| Indicates that a packet has been received that passes the dial-on-demand access lists. That packet causes dialing of a phone number. The xxxxxxxxxx variable is the number being called. |
| Displayed if the phone call could not be placed. This can be due to a lack of memory, full output queues, or other problems. |
| Displayed when the Cisco AS5300 attempts to hang up a call. |
| One of these three messages is displayed when their corresponding dialer timer expires. They are mostly informational, but are useful when debugging a disconnected call or call failure. |
Router# debug isdn q931
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/0:22, changed state to up
ISDN Event: Call to 9086154535 dsl 3 at 64 Kb/s
TX -> SETUP dsl = 3 pd = 8 callref = 0x188C
Bearer Capability i = 0x8890
Channel ID i = 0xE1808397
Called Party Number i = 0xA1, '95163287448'
RX <- RELEASE_COMP dsl = 3 pd = 8 callref = 0x988C
Cause i = 0x83E020 - Mandatory IE missing
ISDN PRI 3: entering process_rxstate, CALL_CLEARED
ISDN PRI 3: received message 1F
ISDN Event: Hangup call to call id 0xCE2 on dsl 2
| Message | Description |
|---|---|
| Indicates this message is being transmitted from the local router (user side) to the network side of the ISDN interface. |
| Indicates this message is being received by the user side of the ISDN interface from the network side. |
| Indicates the SETUP message has been sent to initiate call establishment between peer network layers. The message can be sent from the local router or network. |
| Indicates the protocol discriminator. The protocol discriminator distinguishes messages for call control over the user-network ISDN interface from other ITU-T11-defined messages, including other Q.931 messages. The protocol discriminator is 8 for call control messages such as SETUP. |
| Indicates the call reference number in hexadecimal. The field value indicates the number of calls made from the router (outgoing calls) or the network (incoming calls). Note that the originator of the SETUP message sets the high-order bit of the call reference number to 0. The destination of the connection sets the high-order bit to 1 in subsequent call control messages, such as the CONNECT message. For example, callref = 0x04 in the request becomes callref = 0x84 in the response. |
| Indicates the requested bearer service to be provided by the network. |
| Indicates the Information Element Identifier. The value depends on the field with which it is associated. Refer to the ITU-T Q.931 specification for details about the possible values associated with each field for which this identifier is relevant. |
| Indicates the Channel Identifier. The value 83 indicates any channel, 89 indicates the B1 channel, and 8A indicates the B2 channel. For more information about the Channel Identifier, refer to ITU-T Recommendation Q.931. |
| Identifies the called party. This field is only present in outgoing SETUP messages. It can be replaced by the Keypad facility field. This field uses the IA5 character set. |
| Indicates that the sending equipment will release the channel and call reference. The recipient of this message should prepare to release the call reference and channel. |
| Indicates that the sending equipment has received a RELEASE message and has now released the call reference and channel. |
| 1ITU-T1 = International Telecommunication Union Telecommunication Standarization Sector. |
| Step | Command | Purpose | ||
|---|---|---|---|---|
| | Configure support for the NI2 local ISDN PRI switch type. This switch type is enhanced to support communication between the access server and the external Cisco Signaling Controller SC2200. | ||
| | Specify a D-channel serial interface. Replace the number argument with a controller number followed by a colon (:) and D-channel number. For example, a Cisco AS5300 T1 configuration can have either 0:23, 1:23, 2:23, or 3:23. A Cisco AS5300 E1 configuration can have either 0:15, 1:15, 2:15, or 3:15. | ||
| | Allow ISDN service COT messages to pass through the D channel. This command is disabled by default. This command must also be configured on each D-channel interface that is involved in SS7 call signaling control. |
A COT request comes into the NAS, as indicated by the field COT REQUEST pd. The NAS performs a loopback test on DS0 channel 1, as indicated by the field COT_ServiceMsg: set loop on dsl 0, channel 1. The test operation was a success, as shown by the field COT Result i = 0x02.
Router# debug isdn q931
00:06:38: ISDN Se0:23: RX <- RRp sapi = 0 tei = 0 nr = 0
00:06:38: ISDN Se0:23: TX -> RRf sapi = 0 tei = 0 nr = 0
Router#
00:06:48: ISDN Se0:23: RX <- RRp sapi = 0 tei = 0 nr = 0
00:06:48: ISDN Se0:23: TX -> RRf sapi = 0 tei = 0 nr = 0
Router#
00:06:52: ISDN Se0:23: RX <- INFOc sapi = 0 tei = 0 ns = 0 nr = 0 i = 0x43020003031804E9808381610102620227
00:06:52: COT REQUEST pd = 67 callref = 0x0003
00:06:52: Channel ID i = 0xE9808381
00:06:52: COT Operation i = 0x02
00:06:52: COT Duration i = 0x2702
00:06:52: ISDN Se0:23: TX -> RRr sapi = 0 tei = 0 nr = 1
00:06:52: COT_ServiceMsg: set loop on dsl 0, channel 1
00:06:52: COT_Response(call_id 0x8003, operation 2, result 2) sent
00:06:52: ISDN Se0:23: TX -> INFOc sapi = 0 tei = 0 ns = 0 nr = 1 i = 0x43028003021804E9808381610102630102
00:06:52: COT RESULT pd = 67 callref = 0x8003
00:06:52: Channel ID i = 0xE9808381
00:06:52: COT Operation i = 0x02
00:06:52: COT Result i = 0x02
00:06:52: ISDN Se0:23: RX <- RRr sapi = 0 tei = 0 nr = 1
Router#
00:07:02: ISDN Se0:23: RX <- RRp sapi = 0 tei = 0 nr = 1
00:07:02: ISDN Se0:23: TX -> RRf sapi = 0 tei = 0 nr = 1
Router#
00:07:12: ISDN Se0:23: RX <- RRp sapi = 0 tei = 0 nr = 1
00:07:12: ISDN Se0:23: TX -> RRf sapi = 0 tei = 0 nr = 1
Router#
00:07:14: ISDN Se0:23: RX <- INFOc sapi = 0 tei = 0 ns = 1 nr = 1 i = 0x43020003031804E9808381610101
00:07:14: COT REQUEST pd = 67 callref = 0x0003
00:07:14: Channel ID i = 0xE9808381
00:07:14: COT Operation i = 0x01
00:07:14: ISDN Se0:23: TX -> RRr sapi = 0 tei = 0 nr = 2
00:07:14: COT_ServiceMsg: clear loop on dsl 0, channel 1
00:07:14: COT_Response(call_id 0x8003, operation 1, result 1) sent
00:07:14: ISDN Se0:23: TX -> INFOc sapi = 0 tei = 0 ns = 1 nr = 2 i = 0x43028003021804E9808381610101630101
00:07:14: COT RESULT pd = 67 callref = 0x8003
00:07:14: Channel ID i = 0xE9808381
00:07:14: COT Operation i = 0x01
00:07:14: COT Result i = 0x02
00:07:14: ISDN Se0:23: RX <- RRr sapi = 0 tei = 0 nr = 2
Router#
00:07:24: ISDN Se0:23: RX <- RRp sapi = 0 tei = 0 nr = 2
00:07:24: ISDN Se0:23: TX -> RRf sapi = 0 tei = 0 nr = 2
Router#
00:07:34: ISDN Se0:23: RX <- INFOc sapi = 0 tei = 0 ns = 2 nr = 2 i = 0x43020003031804E9808381610102620227
00:07:34: COT REQUEST pd = 67 callref = 0x0003
00:07:34: Channel ID i = 0xE9808381
00:07:34: COT Operation i = 0x02
00:07:34: COT Duration i = 0x2702
00:07:34: ISDN Se0:23: TX -> RRr sapi = 0 tei = 0 nr = 3
00:07:34: COT_ServiceMsg: set loop on dsl 0, channel 1
00:07:34: COT_Response(call_id 0x8003, operation 2, result 2) sent
00:07:34: ISDN Se0:23: TX -> INFOc sapi = 0 tei = 0 ns = 2 nr = 3 i = 0x43028003021804E9808381610102630102
00:07:34: COT RESULT pd = 67 callref = 0x8003
00:07:34: Channel ID i = 0xE9808381
00:07:34: COT Operation i = 0x02
00:07:34: COT Result i = 0x02
00:07:34: ISDN Se0:23: RX <- RRr sapi = 0 tei = 0 nr = 3
Router#
00:07:39: ISDN Se0:23: RX <- INFOc sapi = 0 tei = 0 ns = 3 nr = 3 i = 0x43020003031804E9808381610101
The isdn service cot command is added for this feature. All other commands used with this feature are documented in the Cisco IOS Release 11.3 command references.
To enable ISDN service COT messages to pass through each D-channel interface involved in SS7 call signaling control, enter the isdn service cot interface configuration command. Use the no form of this command to disable this function.
isdn service cotThis command has no keywords or arguments.
Disabled
Interface configuration
This command first appeared in Cisco IOS Release 11.3 AA.
You must also enable the NI2 switch type, which delivers COT messages to the network access server. The NI2 switch type is enabled with the isdn switch-type primary-ni command.
Use the debug isdn q931 command to display the continuity test debug messages.
debug isdn q931
isdn switch-type primary-ni
For additional software configuration information, see the following publications:
Posted: Wed Feb 17 18:51:10 PST 1999
Copyright 1989-1999©Cisco Systems Inc.