|
|
The chapter guides you through a first time manual installation of Cisco WAN Manager (SV+) and its associated software programs.
When Solaris 2.6 and HP OpenView 5.01 are already installed on your machine and your disk is partitioned to your satisfaction, you are ready to proceed to "Installing the Cisco WAN Manager 9.2 Software".
When you plan to use the HP OpenView 5.01 and/or Wingz 2.5.5 applications in conjunction with the CWM 9.2 product, you must install these applications prior to installing CWM 9.2.
When you plan to use the CiscoView 4.2 application in conjunction with the CWM 9.2 product, you do not have to install CiscoView 4.2 prior to installing CWM 9.2.
You can install the CWM 9.2 software from either a locally attached or remote CD-ROM drive. When you invoke the installation script from a remote drive, the remote and local platforms do not have to be running the same operating system. Following is a list of the tasks you must perform to load and mount the CD-ROM, install the CWM 9.2 and associated software, configure the various product components, and start the CWM 9.2 software.
1. Load the CD into the CD-ROM drive. See "Loading the CD-ROM".
2. Mount the CD-ROM drive. See "Mounting the Locally Attached CD-ROM Drive".
3. Export the CD-ROM drive to make it available to other machines if you are installing the software on a remote machine. See "Mounting a Remotely Attached CD-ROM Drive".
4. Manually install the CWM 9.2 software packages. See "Installing Cisco WAN Manager Manually".
5. Configure the Statistics Collection Manager. See Section, "Configuring Statistics Collection Manager" in Chapter 5.
6. Start the CWM 9.2 software. See Section, "Initial Start-Up of Cisco WAN Manager" in Chapter 5.
7. How to configure a modem for dial-in support. See Section, "Customer Service Dial-In to Cisco WAN Manager Via Modem" in Chapter 5.
8. How to remotely start the SV+ Graphical User Interface. See section, "Starting the Cisco WAN Manager Desktop from a Remote Workstation" in Chapter 5.
The CWM 9.2 software can be loaded from either a locally attached or remote CD-ROM drive.
Step 1 Remove the CWM 9.2 CD from the case and insert it into the CD-ROM drive.
Step 2 Log in as super user root:
host% su
host% Password: <su root password>
host#
The mount instructions for a locally attached CD-ROM drive for the Solaris operating system are provided in this section.
Step 1 When a CD-ROM drive mount point does not exist, create one as follows:
host# mkdir /cdrom
host# mkdir /cdrom/cdrom0
Step 2 Mount the CD-ROM drive on the mount point (when not running Volume Management):
host# /usr/sbin/mount -rF hsfs <device> /cdrom/cdrom0
where <device> is the name of the locally attached CD-ROM drive. For example, to mount the CD-ROM from the local drive named /dev/dsk/c0t6d0s0, specify:
host# /usr/sbin/mount -rF hsfs /dev/dsk/c0t6d0s0 /cdrom/cdrom0
The mount instructions for a remotely attached CD-ROM drive are provided in this section. The CD-ROM drive must be mounted on the remote system (following the steps provided in the previous section), the mount point must then be exported, and it must be mounted on the machine where the CWM 9.2 software is to be installed.
Prior to mounting the CD-ROM drive from the remote host, the device must be made accessible. The following procedures are performed on the remote system (unless otherwise noted) where the CD-ROM drive is attached:
Step 1 If the following entry does not exist in the /etc/exports file, append it to the file. This allows the remote system to export the /cdrom mount point.
/cdrom -ro
Step 2 Export the /cdrom directory from the remote host:
host# /usr/etc/exportfs /cdrom
Step 3 If they are not already running, start the following NFS mount daemons:
host# /usr/etc/nfsd 8
host# /usr/etc/rpc.mountd
Step 4 Verify the mount point is being exported by the remote host. The listing produced by this command should include the /cdrom mount point.
host# /usr/etc/exportfs
Step 5 On the client machine, verify the mount point on the remote host:
host# /usr/sbin/showmount -e <remote_server> | grep cdrom
where <remote_server> is the name of the remote host where the CD-ROM drive is mounted.
Step 6 On the client machine, mount the remotely installed CD-ROM device:
host# /usr/sbin/mount <remote_server>: /cdrom /cdrom/cdrom0
Step 7 Proceed to "Installing Cisco WAN Manager Manually".
Prior to mounting the CD-ROM drive from the remote host, the device must be made accessible. The following procedures are performed on the remote system (unless otherwise noted) where the CD-ROM drive is attached:
Step 1 When they are not already running, start the following NFS mount daemons:
host# /usr/lib/nfs/nfsd 8
host# /usr/lib/nfs/mountd
Step 2 Share the mount point from the remote system:
host# /usr/sbin/share -F nfs -o ro /cdrom/cdrom0
Step 3 Verify the remote host is exporting the mount point. The listing produced by this command should include the /cdrom mount point.
host# /usr/sbin/share
Step 4 On the client machine, verify the mount point on the remote host:
host# /usr/sbin/showmount -e <remote_server> | grep cdrom
where <remote_server> is the name of the remote host where the CD-ROM drive is mounted.
Step 5 On the client machine, mount the remotely installed CD-ROM device:
host# /usr/sbin/mount <remote_server>: /cdrom/cdrom0 /cdrom/cdrom0
Step 6 Proceed to "Installing Cisco WAN Manager Manually".
For the manual installation of CWM Release 9.2 to complete successfully, you must have:
Before installing CSCOsv, make sure you have sufficient free disk space. The CSCOsv software package requires at least 400 MB of free disk space.
To perform an initial installation of CWM 9.2, complete the following steps:
Step 1 If you are not already logged in as user root, do so now.
Step 2 Insert the CWM Release 9.2 CD into the CD-ROM drive.
Step 3 The installation of the CWM 9.2 for HP OpenView package files is complete.
Following is an excerpt from the CSCOconf installation script. Respond to the prompts as appropriate. The default response is shown in boldface type. You must be logged in as root.
Step 1 Insert the CWM 9.2 CD into the CD-ROM drive.
Step 2 If you are not logged in as user root, do so now.
Step 3 When the CD-ROM drive is not already mounted, or you are not running the Volume Manager with Solaris on a Sun SPARC system, at the command line prompt, type:
host# volcheck
Step 4 At the command line prompt, type:
host# pkgadd -d /cdrom/cdrom0 CSCOconf
The CSCOconf package installation process is initiated:
Processing package instance <CSCOconf> from </cdrom/sv920msol>.
Cisco WAN Manager 9.2.00.SOL Configuration
(sparc) 9.2.00.SOL
Cisco WAN Manager 9.2.00.SOL
Copyright (c) 1996, 1997, 1998, 1999 Cisco Systems, Inc. All rights reserved.
This software product is copyrighted and all rights are reserved by
Cisco Systems, Inc. Cisco Systems, Inc. reserves the right to make periodic
modifications to this product without obligation to notify any person
or entity of such revision. Copying, duplicating, selling, or otherwise
distributing any part of this product without the prior written consent
of an authorized representative of Cisco Systems, Inc. is prohibited.
IPX, BPX8600, MGX8220, MGX8850, and FastPacket are registered trademarks and
Cisco WAN Manager is a trademark of Cisco Systems, Inc.
The selected base directory </var/SVconfig> must exist before
installation is attempted.
Do you want this directory created now [y,n,?,q] y <Return>
Using </var/SVconfig> as the package base directory.
## Processing package information.
## Processing system information.
## Verifying package dependencies.
## Verifying disk space requirements.
## Checking for conflicts with packages already installed.
## Checking for setuid/setgid programs.
This package contains scripts which will be executed with super-user
permission during the process of installing this package.
Do you want to continue with the installation of <CSCOconf> [y,n,?] y <Return>
Installing Cisco WAN Manager 9.2.00.SOL Configuration as <CSCOconf>.
## Installing part 1 of 1.
/var/SVconfig/Accounts.pack/Install.sh
/var/SVconfig/Accounts.pack/PostInstall.sh
/var/SVconfig/Accounts.pack/PreInstall.sh
.
.
.
/var/SVconfig/install_config
/var/SVconfig/pkgask.list
[verifying class <none>]
## Executing postinstall script.
Installation of <CSCOconf> was successful.
You must invoke the install_config program to perform disk partitioning and to extract other relevant software packages.
Step 1 At the command line prompt, type:
host# cd /var/SVconfig
Step 2 Invoke the installer script, type:
host# ./install_config
The system prompts you as follows:
Do you want to do an Auto Install or a Manual Install? [a|m)(default(auto):m <Return>
Are you installing from a <spool> directory or <cdrom>? cdrom <Return>
The system only prompts you with the following message when a Manual Install is performed for the first time on this workstation. When this is not the case, the script continues with the: "Using /cdrom/cdrom0 as device name." message below, therefore, you can skip steps 3 and 4. When it is a first time auto installation, the following prompt is displayed:
Reboot the workstation and then run install_config from /var/SVconfig again. Press <Return> to reboot the machine or Ctrl-c to quit: <Return>
Step 3 Login as user root.
Step 4 Change directory to the CWM 9.2 installation directory, then invoke the installation script:
host# cd /var/SVconfig
host# ./install_config
Using /cdrom/cdrom0 as device name. Running the Cisco WAN Manager Installer driver. *** Starting main driver script at Wed Oct 14 16:59:05 PST 1998. *** ******************************************************************************* * * * Welcome to the Cisco WAN Manager Installer! * * * * This program will install the Cisco WAN Manager software * * on your workstation. * * * * Copyright (c) 1997, 1998, 1999 Cisco Systems, Inc. All rights reserved. * * * ******************************************************************************* *** Checking basic setup. *** Cisco WAN Manager is not currently installed. ***** Installing user accounts. ***** *** Finished installing user accounts. ***
****** Installing INFORMIX software package. ******
Extracting the Informix files from CD. This will take a while.
Installing CSCOinf from /cdrom/cdrom0.
Processing package instance <CSCOinf> from </cdrom/sv9104sol>.
INFORMIX 7.23 UC4 for Cisco WAN Manager 9.2.00.SOL
(sparc) 7.23.UC4
==============================================
INFORMIX-OnLine Dynamic Server 7.23.UC4
==============================================
Using </usr/users/informix72> as the package base directory.
Processing package information.
Processing system information.
Installing INFORMIX 7.23.UC4 for Cisco WAN Manager 9.2.00.SOL as <CSCOinf>.
## Installing part 1 of 1.
/usr/users/informix72/README.TXT
/usr/users/informix72/README.UNX
/usr/users/informix72/aaodir/adtcfg
.
.
.
/usr/users/informix72/snmp/snmpr/view.pty
[verifying class <none>]
## Executing postinstall script.
Installation of <CSCOinf> was successful.
Extracting the Cisco WAN Manager files from CD. This will take a while.
Preparing /var/tmp on the secondary disk for svplus pkgadd.
This will temporarily allocate space from /usr/users/svplus/tmp and
link it to /var/tmp.
Removing /var/tmp and linking it to /usr/users/svplus/tmp.
Installing CSCOsv from /cdrom/cdrom0.
This will take approximately 40 minutes.
Processing package instance <CSCOsv> from </cdrom/sv9104sol>.
Cisco WAN Manager 9.2 for HPOV
(sparc) 9.2
Cisco WAN Manager 9.2.00.SOL
Copyright (c) 1996, 1997, 1998 Cisco Systems, Inc. All rights reserved.
This software product is copyrighted and all rights are reserved by
Cisco Systems, Inc. Cisco Systems, Inc. reserves the right to make periodic
modifications to this product without obligation to notify any person
or entity of such revision. Copying, duplicating, selling, or otherwise
distributing any part of this product without the prior written consent
of an authorized representative of Cisco Systems, Inc. is prohibited.
IPX, BPX8600, MGX8220, MGX8850, and FastPacket are registered trademarks and
Cisco WAN Manager is a trademark of Cisco Systems, Inc.
Using </usr/users/svplus> as the package base directory.
Processing package information.
Processing system information.
Installing Cisco WAN Manager 9.2.00.SOL for HPOV as <CSCOsv>.
## Installing part 1 of 1.
/usr/users/svplus/.Xdefaults
/usr/users/svplus/.cshrc
/usr/users/svplus/.cshrc.contrib
.
.
.
/usr/users/svplus/xnmevents_ibm.contrib
[verifying class <none>]
## Executing postinstall script.
Installation of <CSCOsv> was successful.
Welcome to the Installation of Cisco WAN Manager Release 9.2.00.SOL Wed Oct 14 17:49:51 PDT 1998
Raw device name: /dev/rdsk/c0t2d0s7
Checking existence of the sqlhosts file .... Successful
Checking existence of the informix_istar entry.... Successful
Checking for the existence of Informix............ Successful
Checking for the existence of Wingz............... Successful
Wingz is not installed properly under /usr/users/Wingz.
After Cisco WAN Manager installation, install Wingz under
/usr/users/Wingz and then run IntegrateWingz.
Truncating the Informix root database size to maximum allowed 2 GB.
Installation Type for Cisco WAN Manager Release 9.2.00.SOL
--------------------------------------------------
(1) NEW (Release 9.2.00.SOL of SV+)
(2) UPGRADE (From previous release of SV+)
Enter number corresponding to installation type or x to exit: 1 <Return>
Checking existing partition....................... Successful
Available partitions (Solaris):
================================
/dev/rdsk/c0t4d0s7 (1960 MB)
Checking Hard Disk count.......................... Successful
Disk Configuration Migration to Cisco WAN Manager Release 9.2.00.SOL
1) Single Raw Database Disk
2) Multiple Raw Database Disk
x) To Exit
Enter number corresponding to disk configuration or x to exit: 1 <Return>
Enter Raw Partition Name for rootdb (default: Not configured): /dev/rdsk/c0t4d0s7 <Return>
Checking existence of the sqlhosts file .... Successful
Checking existence of the informix_istar entry.... Successful
Creating init_db boot up script................... Successful
Filtering files................................... Successful
Checking for the existence of Informix............ Successful
Checking for the existence of Wingz............... Successful
Enter new database name that starts with a letter and contains fewer than
10 characters (default is stratacom): <Return>
Informix data will be installed in rootdbs: /dev/rdsk/c0t4d0s7 (1960MB) (Default is Y)
OK to continue (Y/N): Y <Return>
Initializing the Informix database. This will take a few minutes...
Shutting down Informix (if necessary)............. Successful
Initializing the Informix database root file...... Successful
Initializing the Informix database mode........... Successful
Preparing the database for Cisco WAN Manager........ Successful
Checking for existence of INS....
INS is not installed in /usr/users/svplus.
Installing Cisco WAN Manager SNMP Agent................. Successful
Searching for CiscoView in default directory...
Did not find CiscoView in default location.
CiscoView 4.2 will be used for Equipment Management.
Have you already installed CiscoView? [Y,N] N <Return>
If you are planning to perform Equipment Management, you must:
a) Install CiscoView 4.2
b) Run the IntegrateCV script
Continuing...
Checking for existence of HP OpenView...
Found HP OpenView installed in /opt/OV.
Installing HP OpenView related files. This will take a few minutes...
Installing Openview patches... Please wait.
Stopping Openview daemons...
Installing Patch: PSOV_02091.
Updating HPOV DB Schema with SV+ extensions....... Successful
Start unloading and loading MIBs. Please see /usr/users/svplus/hpov_install.log
for details.
Loading StrataCom MIB(s) into HPOV......Successful
Installation has completed successfully.
*** Exiting main driver at Wed Mar 24 16:58:04 PST 1999 ***
Posted: Wed Mar 31 15:10:34 PST 1999
Copyright 1989-1999©Cisco Systems Inc.