|
|
The Routed WAN Management Solution consists of five CD-ROMs.
You must install the following CD-ROMs on the same system and in the sequence shown:
1. CiscoWorks2000 CD One (CD One)---consists of CiscoWorks2000 server (common set of management services for CiscoWorks2000 family products), CiscoView (graphical device management tool), and Integration Utility (support for third-party network management systems)
2. Resource Manager Essentials (Essentials) 3.0
3. Access Control List (ACL) Manager 1.1
The following applications are standalone. You can install them on the CiscoWorks2000 server (after you install CD One and Essentials) or on a different system. If you have a large network, it is recommended that you install them on a different system.
You must install the software in this bundle on systems that meet specific requirements. You must configure client systems and some applications before use. The table on the following pages shows basic requirements, installation order, and the required and recommended configuration tasks. For step-by-step procedures and information about all features, refer to the online help and the documents shown in the table.
Before installing any of the software in this package:
 | Caution If you are upgrading from a previous version of Essentials and have integrated Essentials with Netsys, please read the Netsys integration upgrade procedures in Installing and Setting Up Resource Manager Essentials on Solaris, Chapter 2, before installing CD One. |
| Task | Procedure | References | |||
|---|---|---|---|---|---|
| Step 1 | Make sure minimum server requirements are met:
| Installing and Setting Up CD One, Chapter 1 | ||
You must follow the sequence of installation in this table; CD One must be installed before Essentials, and Essentials must be installed before ACL Manager. To install and run all three requires at least 4 GB available disk space. If you are managing more than 100 devices with Essentials, refer to the Essentials installation guide for further system recommendations. | |||||
Step 2 | Read the release notes and installation guide. The release notes might contain last-minute updates to the installation instructions. | CiscoWorks2000 CD One 1st Edition Release Notes | |||
Step 3 | Install CD One. If ACL Manager 1.0 was previously installed on the server, the CD One installation will fail. You must back up your ACL Manager data and remove ACL Manager 1.0 before installing CD One. Refer to the ACL Manager 1.1 documentation. Note If you are upgrading from CWSI Campus 2.2, 2.3, or 2.4 or upgrading from Essentials 2.0, 2.1, or 2.2, the CD One installation program removes the previous CWSI or Essentials software and saves the database(s). You cannot reinstall CWSI Campus on the server after installing Essentials 3.0. | Installing and Setting Up CD One, Chapter 2 | |||
Step 4 | Reboot the system. |
| |||
Step 5 | (Optional) Verify or troubleshoot the installation. | Installing and Setting Up CD One, Troubleshooting appendix | |||
| Step 1 | Make sure client systems meet minimum requirements:
| Installing and Setting Up CD One, Chapter 1 | ||
Step 2 | (Recommended) Set up user accounts. | Getting Started with CiscoWorks2000 Server | |||
| Step 1 | Make sure minimum server requirements are met:
| Installing and Setting Up Resource Manager Essentials, Chapter 1 | ||
Step 2 | Read the release notes and installation guide. The release notes may contain last-minute updates to the installation instructions. The installation guide contains important server recommendations if you are managing more than 100 devices. | Resource Manager Essentials 3.0 Release Notes | |||
Step 3 | Run the Essentials installation program on the server on which you installed CD One. Note If you are upgrading from a previous version of Essentials, the installation program converts and imports the database saved during CD One installation. | Installing and Setting Up Resource Manager Essentials, Chapter 1 | |||
Step 4 | (Optional) Verify or troubleshoot the installation. | Installing and Setting Up Resource Manager Essentials, Troubleshooting appendix | |||
| Step 1 | Configure the server. | Installing and Setting Up Resource Manager Essentials, Chapter 2 | ||
Step 2 | Prepare Essentials applications for use.
| ||||
| Step 1 | Make sure server requirements are met. | Installing Access Control List Manager | ||
Step 2 | Read the release notes for any last-minute updates to the installation instructions. | ACL Manager 1.1 Release Notes | |||
Step 3 | Run the installation program on the server on which you installed CD One and Essentials. | Installing Access Control List Manager | |||
| Note After installation, ACL Manager is integrated with the CiscoWorks2000 navigation tree. |
| ||||
| To install IPM: Note IPM server software runs on a Solaris system only. IPM client software runs on either a Solaris system or a Windows NT system. | Internetwork Performance Monitor Installation Guide: Software Release 2.0
Release Notes for Internetwork Performance Monitor Software Release 2.0 | |||
Step 1 | Make sure IPM server and client requirements are met. | ||||
Step 2 | Read the installation guide and release notes. | ||||
Step 3 | Run the installation program to install the IPM server, IPM client, or both on a Solaris system. Note You can install IPM on the CiscoWorks2000 server or on a different system. If you have a large network, it is recommended that you install it on a different system. | ||||
| To install TrafficDirector: Note You can install TrafficDirector on the CiscoWorks2000 server or on a different system. If you have a large network, it is recommended that you install it on a different system. | TrafficDirector Release 5.7.2 Installation Guide for Windows NT and Solaris
Release Notes for TrafficDirector Release 5.7.2 | |||
| Step 1 | Make sure server requirements are met. | |||
| Step 2 | Read the installation guide; it contains special cautions you must be aware of. | |||
| Step 3 | Read the release notes for any last-minute updates to the installation instructions. | |||
| Step 4 | Run the installation program. | |||
|
| It is strongly recommended that you use the default installation path of /opt/CSCOtd5. To override the default and install in an existing location, use a directory subordinate to the existing location (for example, /alternate_location/CSCOtd5). | |||
| Step 5 | Configure the SQL servers. | |||
| Step 6 | Set up the database. | |||
Posted: Thu Mar 30 18:51:34 PST 2000
Copyright 1989 - 2000©Cisco Systems Inc.