|
|
This chapter describes how to use the command-line interface (CLI) to configure EtherChannel on the Catalyst 6000 family switches. The configuration tasks in this chapter apply to Ethernet, Fast Ethernet, and Gigabit Ethernet switching modules, as well as to the uplink ports on the supervisor engine.
 |
Note For complete syntax and usage information for the commands used in this chapter, refer to the Catalyst 6000 Family Command Reference publication. |
This chapter consists of these sections:
|
Note The commands in the following sections can be used on all Ethernet ports in the Catalyst 6000 family switches. |
EtherChannel bundles individual Ethernet links into a single logical link that provides bandwidth up to 1600 Mbps (Fast EtherChannel full duplex) or 16 Gbps (Gigabit EtherChannel) between a Catalyst 6000 family switch and another switch or host.
A Catalyst 6000 family switch supports a maximum of 128 EtherChannels. You can form an EtherChannel with up to eight compatibly configured Ethernet ports on any module in a Catalyst 6000 family switch. All ports in each EtherChannel must be the same speed.
|
Note The network device to which a Catalyst 6000 family switch is connected may impose its own limits on the number of ports in an EtherChannel. |
If a segment within an EtherChannel fails, traffic previously carried over the failed link switches to the remaining segments within the EtherChannel. A trap is sent upon a failure identifying the switch, the EtherChannel, and the failed link. Inbound broadcast and multicast packets on one segment in an EtherChannel are blocked from returning on any other segment of the EtherChannel.
EtherChannels can be configured as trunks. After a channel has been formed, configuring any port in the channel as a trunk applies the configuration to all ports in the channel. Identically configured trunk ports can be configured as an EtherChannel.
Configuring an EtherChannel creates an administrative group, designated by an integer between 1 and 1024, to which the EtherChannel belongs. When an administrative group is created, you can assign an administrative group number or let the next available administrative group number be assigned automatically. Forming a channel without specifying an administrative group number creates a new automatically numbered administrative group. An administrative group may contain a maximum of eight ports.
Each EtherChannel is automatically assigned a unique EtherChannel ID. Use the show channel group admin_group command to display the EtherChannel ID.
The Port Aggregation Protocol (PAgP) facilitates the automatic creation of EtherChannels by exchanging packets between Ethernet ports. PAgP packets are exchanged only between ports in auto and desirable modes. Ports configured in on or off mode do not exchange PAgP packets. The protocol learns the capabilities of port groups dynamically and informs the other ports. Once PAgP identifies correctly matched EtherChannel links, it groups the ports into an EtherChannel. The EtherChannel is then added to the spanning tree as a single bridge port.
EtherChannel includes four user-configurable modes: on, off, auto, and desirable. Only auto and desirable are PAgP modes. The auto and desirable modes can be modified with the silent and non-silent keywords. By default, ports are in auto silent mode.
Table 5-1 describes EtherChannel modes.
| Mode | Description |
|---|---|
on | Mode that forces the port to channel without PAgP. With the on mode, a usable EtherChannel exists only when a port group in on mode is connected to another port group in on mode. |
off | Mode that prevents the port from channeling. |
auto | PAgP mode that places a port into a passive negotiating state, in which the port responds to PAgP packets it receives but does not initiate PAgP packet negotiation. (Default) |
desirable | PAgP mode that places a port into an active negotiating state, in which the port initiates negotiations with other ports by sending PAgP packets. |
silent | Keyword that is used with the auto or desirable mode when no traffic is expected from the other device to prevent the link from being reported to the Spanning-Tree Protocol as down. (Default) |
non-silent | Keyword that is used with the auto or desirable mode when traffic is expected from the other device. |
Both the auto and desirable modes allow ports to negotiate with connected ports to determine if they can form an EtherChannel, based on criteria such as port speed, trunking state, and VLAN numbers.
Ports can form an EtherChannel when they are in different PAgP modes as long as the modes are compatible. For example:
EtherChannel distributes frames across the links in a channel by reducing part of the binary pattern formed from the addresses in the frame to a numerical value that selects one of the links in the channel.
Enter a show module command for the supervisor engine to determine if EtherChannel frame distribution is configurable on your switch.
When configurable, EtherChannel frame distribution can use either MAC addresses or IP addresses and either source or destination or both source and destination addresses. The selected mode applies to all EtherChannels configured on the switch.
Use the option that provides the greatest variety in your configuration. For example, if the traffic on a channel is only going to a single MAC address, using the destination MAC address always chooses the same link in the channel; using source addresses or IP addresses may result in better frame distribution.
If improperly configured, some EtherChannel ports are disabled automatically to avoid network loops and other problems. Follow these guidelines to avoid configuration problems:
These sections describe how to configure EtherChannel:
|
Note Make sure that the ports are configured correctly. (See the "EtherChannel Configuration Guidelines" section.) |
To configure EtherChannel on a group of Ethernet ports, perform this task in privileged mode:
| Task | Command |
|---|---|
Configure the EtherChannel on the desired ports. | set port channel mod/ports... [admin_group] |
This example shows how to configure a seven-port EtherChannel in a new administrative group:
Console> (enable) set port channel 2/2-8 desirable Ports 2/2-8 left admin_group 1. Ports 2/2-8 joined admin_group 2. Console> (enable)
To set a port's EtherChannel mode, perform this task in privileged mode:
| Task | Command |
|---|---|
Set a port's EtherChannel mode. | set port channel mod/ports... [admin_group] |
This example shows how to set port 2/1 to auto mode:
Console> (enable) set port channel 2/1 mode auto Ports 2/1 channel mode set to auto. Console> (enable)
To set the EtherChannel port path cost, perform this task in privileged mode:
| Task | Command | |
|---|---|---|
Step 1 | Use the administrative group number to display the EtherChannel ID. | show channel group admin_group |
Step 2 | Use the EtherChannel ID to set the EtherChannel port path cost. | set channel cost {channel_id | all} cost |
This example shows how to set the EtherChannel port path cost for channel ID 768:
Console> (enable) show channel group 20 Admin Port Status Channel Channel group Mode id ----- ----- ---------- --------- -------- 20 1/1 notconnect on 768 20 1/2 connected on 768 Admin Port Device-ID Port-ID Platform group ----- ----- ------------------------------- ------------------------- ---------- 20 1/1 20 1/2 066510644(cat26-lnf(NET25)) 2/1 WS-C6009 Console> (enable) Console> (enable) set channel cost 768 12 Port(s) 1/1,1/2 port path cost are updated to 31. Channel 768 cost is set to 12. Warning:channel cost may not be applicable if channel is broken. Console> (enable)
To set the EtherChannel VLAN cost, perform this task in privileged mode:
| Task | Command | |
|---|---|---|
Step 1 | Use the administrative group number to display the EtherChannel ID. | show channel group admin_group |
Step 2 | Use the EtherChannel ID to set the EtherChannel VLAN cost. | set channel vlancost channel_id cost |
This example shows how to set the EtherChannel VLAN cost for channel ID 768:
Console> (enable) show channel group 20 Admin Port Status Channel Channel group Mode id ----- ----- ---------- --------- -------- 20 1/1 notconnect on 768 20 1/2 connected on 768 Admin Port Device-ID Port-ID Platform group ----- ----- ------------------------------- ------------------------- ---------- 20 1/1 20 1/2 066510644(cat26-lnf(NET25)) 2/1 WS-C6009 Console> (enable) Console> (enable) set channel vlancost 768 12 Channel 768 vlancost set to 12. Console> (enable)
To configure EtherChannel frame distribution, perform this task in privileged mode:
| Task | Command |
|---|---|
Configure EtherChannel frame distribution. | set port channel all distribution {ip | mac} [source | destination | both] |
This example shows how to configure EtherChannel to use MAC source addresses:
Console> (enable) set port channel all distribution mac source Channel distribution is set to mac source. Console> (enable)
To disable an EtherChannel, perform this task in privileged mode:
| Task | Command |
|---|---|
Disable an EtherChannel. | set port channel mod_num/port_num mode off |
This example shows how to disable an EtherChannel:
Console> (enable) set port channel 2/2-8 mode off Ports 2/2-8 channel mode set to off. Console> (enable)
Posted: Sun Jun 11 03:08:37 PDT 2000
Copyright 1989 - 2000©Cisco Systems Inc.