Table of Contents

2 2

set summertime

Use the set summertime command to specify whether the system should set the clock ahead one hour during daylight saving time.

Syntax Description

enable	Keyword to cause the system to set the clock ahead one hour during daylight saving time.
disable	Keyword to prevent the system from setting the clock ahead one hour during daylight saving time.
zone	(Optional) Time zone used by the set summertime command.
recurring	Keyword to specify the summertime dates which recur every year.
week	Week of the month (first, second, third, fourth, last, 1...5).
day	Day of the week (Sunday, Monday, Tuesday, and so forth).
month	Month of the year (January, February, March, and so forth).
hh:mm	Hours and minutes.
offset	(Optional) Amount of offset in minutes (1 to 1440 minutes).
date	Day of the month (1 to 31).
year	Number of the year (1993 to 2035).

Defaults

By default, the set summertime command is disabled. Once enabled, the default for offset is 60 minutes, following U.S. standards.

Command Types

Switch command.

Command Modes

Privileged.

Usage Guidelines

After you enter the clear config command, the dates and times are set to default.

Unless you configure it otherwise, this command advances the clock one hour at 2:00 a.m. on the first Sunday in April and moves back the clock one hour at 2:00 a.m. on the last Sunday in October.

Examples

This example shows how to cause the system to set the clock ahead one hour during daylight saving time:

Console> (enable) set summertime enable PDT
Summertime is enabled and set to "PDT".
Console> (enable)
 

This example shows how to prevent the system from setting the clock ahead one hour during daylight saving time:

Console> (enable) set summertime disable
Summertime disabled.
Console> (enable)
 

This example shows how to set daylight saving time to the zonename AUS and repeat every year, starting from the third Monday of February at noon and ending at the second Saturday of August at
3:00 p.m. with an offset of 30 minutes:

Console> (enable) set summertime AUS recurring 3 Mon Feb 12:00 2 Saturday Aug 15:00 30
Summer time is disabled and set to 'AUS' with offset 30 minutes.
   start: 12:00:00 Sun Feb 13 2000
   end:   14:00:00 Sat Aug 26 2000
   Recurring, starting at 12:00:00 on Sunday of the third week of February and ending    on Saturday of the fourth week of August.
Console> (enable)
 

This example shows how to set the daylight saving time to start on January 29, 1999 at 2:00 a.m. and end on August 19, 2004 at 3:00 p.m. with an offset of 30 minutes:

Console> (enable) set summertime date jan 29 1999 02:00 aug 19 2004 15:00 30 
Summertime is disabled and set to ''
Start : Fri Jan 29 1999, 02:00:00
End   : Thu Aug 19 2004, 15:00:00
Offset: 30 minutes
Recurring: no
Console> (enable) 
 

This example shows how to set recurring to reset default to US summertime:

Console> (enable) set summertime recurring 3 mon feb 4 thurs oct 8:00 500
Command authorization none.
Summertime is enabled and set to `'
Start : Mon Feb 21 2000, 03:00:00
End   : Fri Oct 20 2000, 08:00:00
Offset: 500 minutes (8 hours 20 minutes)
Recurring: yes, starting at 03:00am of third Monday of February and ending on 08:00am of fourth Thursday of October.
Console> (enable) 

Related Commands

show summertime

set system baud

Use the set system baud command to set the console port baud rate.

Syntax Description

rate	Baud rate; valid rates are 600, 1200, 2400, 4800, 9600, 19200, and 38400.

Defaults

The default is 9600 baud.

Command Types

Switch command.

Command Modes

Privileged.

Examples

This example shows how to set the system baud rate to 19200:

Console> (enable) set system baud 19200
System console port baud rate set to 19200.
Console> (enable) 

Related Commands

show system

set system contact

Use the set system contact command to identify a contact person for the system.

Syntax Description

contact_string

(Optional) Text string that contains the name of the person to contact for system administration. If you do not specify a contact string, the system contact string is cleared.

Defaults

The default is no system contact is configured.

Command Types

Switch command.

Command Modes

Privileged.

Examples

This example shows how to set the system contact string:

Console> (enable) set system contact Xena ext.24
System contact set.
Console> (enable) 

Related Commands

show system

set system countrycode

Use the set system countrycode command to specify the country where the system is physically located.

Syntax Description

code	Country code; see the "Usage Guidelines" section for format information.

Defaults

The default is US (United States).

Command Types

Switch command.

Command Modes

Privileged.

Usage Guidelines

The country code is a 2-letter country code taken from ISO-3166 (for example, VA=Holy See (Vatican City State) , VU=Vanuatu, and TF=French Southern Territories).

Examples

This example shows how to set the system country code:

Console> (enable) set system countrycode US
Country code is set to US.
Console> (enable) 

set system highavailability

Use the set system highavailability command to enable or disable high system availability for the switch.

Syntax Description

enable	Keyword to activate system high availability.
disable	Keyword to deactivate system high availability.

Defaults

The default is disabled.

Command Types

Switch command.

Command Modes

Privileged.

Usage Guidelines

High availability provides Layer 2 to Layer 3 protocol redundancy.

If you enable high availability while the standby supervisor engine is running, the switch checks the version compatibility between the two supervisor engines. If the versions are compatible, database synchronization occurs. When you disable high availability, database synchronization does not occur and protocols restart on the standby supervisor engine after switchover.

If you disable high availability from the enabled state, synchronization from the active supervisor engine is stopped. On the standby supervisor engine, current synchronization data is discarded. If you enable high availability from the disabled state, synchronization from the active to standby supervisor engines starts (if you have a standby supervisor engine and the standby supervisor engine image version is compatible).

Examples

This example shows how to enable high availability:

Console> (enable) set system highavailability enable
System high availability enabled.
Console> (enable) 
 

This example shows how to disable high availability:

Console> (enable) set system highavailability disable
System high availability disabled.
Console> (enable) 

Related Commands

set system highavailability versioning
show system highavailability

set system highavailability versioning

Use the set system highavailability versioning command to enable and disable support for supervisor engine image versioning.

Syntax Description

enable	Keyword to activate system high availability versioning.
disable	Keyword to deactivate system high availability versioning.

Defaults

The default is disabled.

Command Types

Switch command.

Command Modes

Privileged.

Usage Guidelines

The high availability versioning feature allows the Catalyst 6000 family switch to run different images on the active and standby supervisor engines. When you enable image versioning, Flash image synchronization (from active to the standby supervisor engines) does not occur, allowing active and standby supervisor engines to run different images.

Caution When you disable image versioning, the active and standby supervisor engines must run the same image version.

If you disable the image versioning option from the enabled state, no additional action is necessary on the standby supervisor engine (the standby supervisor engine should be running the same image as the active supervisor engine). If you want to load a different images, you have to restart the standby supervisor engine.

If you enable the image versioning option from the disabled state, and you have a standby supervisor engine and active supervisor engine running different images, Flash synchronization will copy the active supervisor engine image to the standby supervisor engine image and then restart it.

If you enable the image versioning option on the active supervisor engine, and the standby supervisor engine is running a different image, the NVRAM synchronization cannot occur because the NVRAM versions are not compatible. If this is the case, after switchover, the old NVRAM configuration on the supervisor engine is used.

Examples

This example shows how to enable high availability versioning:

Console> (enable) set system highavailability versioning enable
Image versioning enabled.
Console> (enable)
 

This example shows how to disable high availability versioning:

Console> (enable) set system highavailability versioning disable
Image versioning disabled.
Console> (enable)

Related Commands

set system highavailability
show system highavailability

set system location

Use the set system location command to identify the location of the system.

Syntax Description

location_string

(Optional) Text string that indicates where the system is located.

Defaults

This command has no default setting.

Command Types

Switch command.

Command Modes

Privileged.

Usage Guidelines

If you do not specify a location string, the system location is cleared.

Examples

This example shows how to set the system location string:

Console> (enable) set system location Closet 230 4/F
System location set.
Console> (enable)

Related Commands

show system

set system modem

Use the set system modem command to enable or disable modem control lines on the console port.

Syntax Description

enable	Keyword to activate modem control lines on the console port.
disable	Keyword to deactivate modem control lines on the console port.

Defaults

The default is modem control lines are disabled.

Command Types

Switch command.

Command Modes

Privileged.

Examples

This example shows how to disable modem control lines on the console port:

Console> (enable) set system modem disable
Modem control lines disabled on console port.
Console> (enable) 

Related Commands

show system

set system name

Use the set system name command to configure a name for the system.

Syntax Description

name_string

(Optional) Text string that identifies the system.

Defaults

The default is no system name is configured.

Command Types

Switch command.

Command Modes

Privileged.

Usage Guidelines

If you use the set system name command to assign a name to the switch, the switch name is used as the prompt string. However, if you specify a different prompt string using the set prompt command, that string is used for the prompt.

Console> (enable) set system name Information Systems
System name set.
Console> (enable) 

show system
set prompt

set tacacs attempts

Use the set tacacs attempts command to configure the maximum number of login attempts allowed to the TACACS+ server.

Console> (enable) set tacacs attempts 6
Tacacs number of attempts set to 6.
Console> (enable) 

show tacacs

set tacacs directedrequest

Use the set tacacs directedrequest command to enable or disable the TACACS+ directed-request option. When enabled, you can direct a request to any of the configured TACACS+ servers and only the username is sent to the specified server.

Usage Guidelines

When you enable TACACS+ directed-request, you must specify a configured TACACS+ server after the @ sign. If the specified host name does not match the IP address of a configured TACACS+ server, the request is rejected. When TACACS+ directed-request is disabled, the Catalyst 6000 family switch queries the list of servers beginning with the first server in the list and then sends the entire string, accepting the first response from the server. This command is useful for sites that have developed their own TACACS+ server software to parse the entire address string and make decisions based on the contents of the string.

Console> (enable) set tacacs directedrequest enable
Tacacs direct request has been enabled.
Console> (enable) 

show tacacs

set tacacs key

Use the set tacacs key command to set the key for TACACS+ authentication and encryption.

Console> (enable) set tacacs key Who Goes There
The tacacs key has been set to Who Goes There.
Console> (enable) 

clear spantree uplinkfast
show tacacs

set tacacs server

Use the set tacacs server command to define a TACACS+ server.

Usage Guidelines

You can configure a maximum of three servers. The primary server, if configured, is contacted first. If no primary server is configured, the first server configured becomes the primary server.

Console> (enable) set tacacs server 170.1.2.20 primary
170.1.2.20 added to TACACS server table as primary server.
Console> (enable) 

clear tacacs server
show tacacs

set tacacs timeout

Use the set tacacs timeout command to set the response timeout interval for the TACACS+ server daemon. The TACACS+ server must respond to a TACACS+ authentication request before this interval expires or the next configured server is queried.

Console> (enable) set tacacs timeout 8
Tacacs timeout set to 8 seconds.
Console> (enable)

show tacacs

set time

Use the set time command to change the time of day on the system clock.

Syntax Description

day_of_week	(Optional) Day of the week.
mm/dd/yy	(Optional) Month, day, and year.
hh:mm:ss	(Optional) Current time in 24-hour format.

Defaults

This command has no default setting.

Command Types

Switch command.

Command Modes

Privileged.

Examples

This example shows how to set the system clock to Saturday, October 31, 1998, 7:50 a.m:

Console> (enable) set time sat 10/31/98 7:50
Sat Oct 31 1998, 07:50:00
Console> (enable)

Related Commands

show time

set timezone

Use the set timezone command to set the time zone for the system.

Syntax Description

zone_name	(Optional) Name of the time zone to be displayed.
hours	(Optional) Number of hours offset from UTC.
minutes	(Optional) Number of minutes offset from UTC. If the specified hours value is a negative number, then the minutes value is assumed to be negative as well.

Defaults

The default is the time zone is set to UTC.

Command Types

Switch command.

Command Modes

Privileged.

Usage Guidelines

The set timezone command is effective only when NTP is running. If you set the time explicitly and NTP is disengaged, the set timezone command has no effect. If you have enabled NTP and have not entered the set timezone command, the Catalyst 6000 family switch displays UTC by default.

Console> (enable) set timezone PST -8
Timezone set to "PST", offset from UTC is -8 hours.
Console> (enable)

clear timezone
show timezone

set trunk

Use the set trunk command to configure trunk ports and to add VLANs to the allowed VLAN list for existing trunks.

Syntax Description

mod/port	Number of the module and the port on the module.
on	Keyword to force the port to become a trunk port and persuade the neighboring port to become a trunk port. The port becomes a trunk port even if the neighboring port does not agree to become a trunk.
off	Keyword to force the port to become a nontrunk port and persuade the neighboring port to become a nontrunk port. The port becomes a nontrunk port even if the neighboring port does not agree to become a nontrunk port.
desirable	Keyword to cause the port to negotiate actively with the neighboring port to become a trunk link.
auto	Keyword to cause the port to become a trunk port if the neighboring port tries to negotiate a trunk link. This is the default mode for EtherChannel ports.
nonegotiate	Keyword to force the port to become a trunk port but prevent it from sending DTP frames to its neighbor.
isl	(Optional) Keyword to specify an ISL trunk on a Fast or Gigabit Ethernet port.
dot1q	(Optional) Keyword to specify an IEEE 802.1Q trunk on a Fast or Gigabit Ethernet port.
negotiate	(Optional) Keyword to specify that the port become an ISL (preferred) or 802.1Q trunk, depending on the configuration and capabilities of the neighboring port.
vlans	(Optional) VLANs to add to the list of allowed VLANs on the trunk; valid values are from 1 to 1000 and 1025 to 4094.

Defaults

The default port mode is 802.1Q-Native.

Command Types

Switch command.

Command Modes

Privileged.

Usage Guidelines

This command is not supported by the NAM.

• If a trunk-type keyword (isl, dot1q, negotiate) is not specified when configuring an EtherChannel trunk, the current trunk type is not affected.

• To return a trunk to its default trunk type and mode, enter the clear trunk mod/port command.

• Trunking capabilities are hardware-dependent. Refer to the Catalyst 6000 Family Module Installation Guide to determine the trunking capabilities of your hardware, or enter the show port capabilities command.

• The Catalyst 6000 family switches use the DTP to negotiate trunk links automatically on EtherChannel ports. Whether a port will negotiate to become a trunk port depends on both the mode and the trunk type specified for that port. Refer to the Catalyst 6000 Family Software Configuration Guide for detailed information on how trunk ports are negotiated.

• DTP is a point-to-point protocol. However, some internetworking devices might improperly forward DTP frames. You can avoid this problem by ensuring that trunking is turned off on ports connected to non-Catalyst 6000 family switch devices if you do not intend to trunk across those links. When enabling trunking on a link to a Cisco router, enter the noneg keyword to cause the port to become a trunk but not generate DTP frames.

• For trunking to be negotiated on EtherChannel ports, the ports must be in the same VTP domain. However, you can use the on or noneg mode to force a port to become a trunk, even if it is in a different domain.

• To remove VLANs from the allowed list for a trunk, enter the clear trunk mod/port vlans command. When you first configure a port as a trunk, the set trunk command always adds all VLANs to the allowed VLAN list for the trunk, even if you specify a VLAN range (the specified VLAN range is ignored).

• To remove VLANs from the allowed list, enter the clear trunk mod/port vlans command. To later add VLANs that were removed, enter the set trunk mod/port vlans command.

• You cannot change the allowed VLAN range on the MSM port. The MSM port can be configured only as an IEEE 802.1Q-type trunk.

Examples

This example shows how to set port 2 on module 1 as a trunk port:

Console> (enable) set trunk 1/2 on
Port(s) 1/2 trunk mode set to on.
Console> (enable)
 

This example shows how to add VLANs 5 through 50 to the allowed VLAN list for a trunk port (VLANs were previously removed from the allowed list with the clear trunk command):

Console> (enable) set trunk 1/1 5-50
Adding vlans 5-50 to allowed list.
Port(s) 1/1 allowed vlans modified to 1,5-50,101-1005.
Console> (enable)
 

This example shows how to set port 5 on module 4 as an 802.1Q trunk port in desirable mode:

Console> (enable) set trunk 4/5 desirable dot1q
Port(s) 4/5 trunk mode set to desirable.
Port(s) 4/5 trunk type set to dot1q.
Console> (enable)

Related Commands

clear trunk
set vtp
show trunk
show vtp statistics

Posted: Tue Sep 19 14:36:10 PDT 2000
Copyright 1989-2000©Cisco Systems Inc.