|
|
Use the clear vtp pruneeligible command to specify which VLANs in the VTP domain are ineligible for pruning.
clear vtp pruneeligible vlan_num
vlan_num | Number of VLANs to make ineligible for pruning; valid values are 1 to 1005. |
By default, VLANs 2 to 1000 are eligible for pruning.
Catalyst 5000 family switches
Catalyst 4000 family switches
Catalyst 2926G series switches
Catalyst 2948G switch
Switch command.
Privileged.
VTP pruning prevents traffic in each pruning-eligible VLAN from being transmitted on a VLAN trunk if no stations belonging to that VLAN are located across that trunk. Use the set vtp command to enable VTP pruning.
Use the set vtp pruneeligible command to make the VLANs eligible for pruning again.
This example shows how to make VLANs 200 to 500 ineligible for pruning:
Console> (enable) clear vtp pruneeligible 200-500 Vlans 1,200-500,1001-1005 will not be pruned on this device. VTP domain Company modified. Console> (enable)
set vtp
set vtp pruneeligible
show vtp statistics
Use the clear vtp statistics command to delete the VTP statistics.
clear vtp statisticsThis command has no arguments or keywords.
This command has no default setting.
Catalyst 5000 family switches
Catalyst 4000 family switches
Catalyst 2926G series switches
Catalyst 2948G switch
Switch command.
Privileged.
This example shows how to clear the VTP statistics:
Console> (enable) clear vtp statistics vtp statistics cleared. Console> (enable)
Use the configure command to download a configuration file from a host and execute each command in that file.
configure host file [rcp]
host | IP address or IP alias of the host. |
file | Name of the configuration file. |
rcp | (Optional) Keyword to specify rcp as file transfer method. |
The default file transfer method is TFTP.
Catalyst 5000 family switches
Catalyst 4000 family switches
Catalyst 2926G series switches
Catalyst 2948G switch
Switch command.
Privileged.
Refer to the Software Configuration Guide for your switch for information on how to construct a configuration file to download using the configure command.
The following is an example configuration file. Each line contains a command, except for the lines that begin with ! or #. On some servers (NT), the TFTP directory might not be /tftpboot.
begin show time set ip alias conc7 198.133.219.207 set ip alias montreux 198.133.119.42 set ip alias cres 192.122.174.42 set prompt system5> set password # empty string old password pingpong pingpong end #
This example shows how to configure the switch using a configuration file downloaded from a TFTP server:
Console> (enable) configure 192.122.174.42 system5.cfg Configure using system5.cfg from 192.122.174.42 (y/n) [n]? y / Done. Finished Network Download. (446 bytes) >> show time Wed Nov 11 1998, 17:42:50 >> set ip alias conc7 198.133.219.207 IP alias added. >> set ip alias montreux 198.133.219.40 IP alias added. >> set ip alias cres 192.122.174.42 IP alias added. >> set prompt system5> >> set password Enter old password: Enter new password: pingpong Retype new password: pingpong Password changed.
This example shows how to configure a Catalyst 5000 family switch with a Supervisor EngineII, IIG, or IIIG using a configuration file downloaded from a rcp server:
Console> (enable) configure 172.20.52.3 dns-config.cfg rcp Finished network download. (134 bytes) >> >> set ip dns server 172.16.10.70 primary 172.16.10.70 added to DNS server table as primary server. >> set ip dns server 172.16.10.140 172.16.10.140 added to DNS server table as backup server. >> set ip dns enable DNS is enabled >> set ip dns domain corp.com Default DNS domain name set to corp.com Console> (enable)
Use the confreg command to set the configuration register value or to modify the configuration register using the configuration register utility.
confreg [hexvalue]
hexvalue | (Optional) Hexadecimal value of the configuration register. |
This command has no defaults.
Catalyst 5000 family switches
Catalyst 4000 family switches
Catalyst 2926G series switches
Catalyst 2948G switch
ROM monitor command.
Normal.
If you specify hexvalue, the confreg command changes the configuration register value to the hexadecimal value specified.
If you do not specify hexvalue, confreg shows the current configuration register values and prompts you to keep or change the current values.
The new configuration register value is written into NVRAM and does not take effect until you reset or power cycle the switch.
This example shows how to use the confreg command:
rommon 1 > confreg
Configuration Summary
enabled are:
console baud:9600
boot:the ROM Monitor
do you wish to change the configuration? y/n [n]: y
enable "diagnostic mode"? y/n [n]:<Return>
enable "use net in IP bcast address"? y/n [n]:<Return>
enable "load rom after netboot fails"? y/n [n]:<Return>
enable "use all zero broadcast"? y/n [n]:<Return>
enable "break/abort has effect"? y/n [n]:<Return>
enable "ignore system config info"? y/n [n]:<Return>
change console baud rate? y/n [n]:<Return>
change the boot characteristics? y/n [n]: y
enter to boot:
0 = ROM Monitor
1 = the boot helper image
2-15 = boot system
[0]: 2
Configuration Summary
enabled are:
console baud:9600
boot:image specified by the boot system commands
or default to:cisco2-Presto
do you wish to change the configuration? y/n [n]:<Return>
You must reset or power cycle for new config to take effect
rommon 2 >
Use the copy command to perform these tasks:
file-id | The file on which to perform the copy action, where file_id is of the format [[m/]device:][filename]. m/ = The module where the Flash device is located (such as the standby supervisor engine, an FDDI module, or an ATM module). Module 1 is assumed if no module is specified. device: = Device where the file is located. Valid Flash devices are bootflash:, slot0:, and slot1:. You can also specify tftp: as the device name. The colon (:) is required after the device name. filename = Name of the system image or configuration file. |
tftp | Keyword that specifies that the file will be copied to or from a TFTP server. |
rcp | Keyword that specifies that the file will be copied to or from an rcp server. |
flash | Keyword that specifies that the file will be copied to or from the Flash file system. |
Keyword that specifies that the switch configuration file will be copied to the specified file, or that the specified file will be used to configure the switch. | |
cfg1 | Keyword that specifies the first startup configuration file on the Supervisor Engine II G and III G. |
cfg2 | Keyword that specifies the second startup configuration file on the Supervisor Engine II G and III G. |
all | Keyword that specifies that the entire configuration be copied to the specified destination configuration file. If you do not use the all keyword, only non-default commands are copied to the destination configuration file. |
By default, the copy config, copy cfg1, and copy cfg2 commands will copy only non-default commands to the destination configuration file. Use the keyword all to copy both default and non-default configurations.
If a source or destination Flash device is not specified, the default Flash device (specified by the cd command) is used. Use the pwd command to display the current default Flash device. If the destination filename is omitted, the system uses the source filename.
The system stores image and configuration files in the sysname.cfg file when the user has defined a system name using the set system name command; otherwise, it uses the default myswitch.cfg file.
Catalyst 5000 family switches
Catalyst 4000 family switches
Catalyst 2926G series switches
Catalyst 2948G switch
Switch command.
Privileged.
This command is not supported on Catalyst 5000 family Supervisor Engine II.
These switches support only the bootflash: Flash device:
The cfg1 and cfg2 startup configuration files are present only on the Catalyst 5000 family Supervisor Engine II G and III G. These files are limited to 256 KB in size.
If you use the flash keyword as the copy source or destination, you are prompted for the Flash device name.
If you are copying a software image to multiple intelligent switching modules of the same type, use the flash keyword as the copy destination. The switch automatically determines which modules to copy the image to based on the header in the source image file. If you want to copy a software image to a single intelligent switching module in a switch with multiple modules of the same type, you must specify the destination file-id as m/bootflash: (do not specify a filename).
This example shows how to upload the non-default switch configuration to a file named cat.cfg on the slot0: Flash device:
Console> (enable) copy config slot0:cat.cfg Upload configuration to slot0:cat.cfg 649324 bytes available on device slot0, proceed (y/n) [n]? y ......... . / Configuration has been copied successfully. (10200 bytes) Console> (enable)
This example shows how to upload both the default and non-default switch configuration to a file named lab2.cfg on a TFTP server:
Console> (enable) copy config tftp:lab2.cfg all IP address or name of remote host [172.20.22.7]? y Upload configuration to imgFile:lab2.cfg (y/n) [n]? y ......... . / Configuration has been copied successfully. (10299 bytes). Console> (enable)
This example shows how to upload the non-default switch configuration to the cat.cfg file on the slot1: Flash device:
Console> (enable) copy config flash Flash device [bootflash]? slot1: Name of file to copy to [configFile]? cat.cfg Upload configuration to slot1:cat.cfg 749124 bytes available on device slot1, proceed (y/n) [n]? y ......... . / Configuration has been copied successfully. (200345 bytes). Console> (enable)
This example shows how to upload an image from a remote host into Flash using rcp:
Console> (enable) copy rcp flash IP address or name of remote host []? 172.20.52.3 Name of file to copy from []? cat5000-sup3.4-2-1.bin Flash device [bootflash]? Name of file to copy to [cat5000-sup3.4-2-1.bin]? 4369664 bytes available on device bootflash, proceed (y/n) [n]? y CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCC File has been copied successfully. Console> (enable)
This example shows how to upload the running configuration on a Catalyst 5000 family switch with a Supervisor Engine III or IIIF, or on a Catalyst4000 family, 2926G series, or 2948G switch, to an rcp server for storage:
Console> (enable) copy config rcp IP address or name of remote host []? 172.20.52.3 Name of file to copy to []? cat5000_config.cfg Upload configuration to rcp:cat5000_config.cfg, (y/n) [n]? y ..... .......... ....... .......... ........... .. / Configuration has been copied successfully. Console> (enable)
This example shows how to configure a Catalyst 5000 family switch with a Supervisor Engine III or IIIF, or a Catalyst4000 family, 2926G series, or 2948G switch using a configuration file downloaded from an rcp server:
Console> (enable) copy rcp config IP address or name of remote host []? 172.20.52.3 Name of file to copy from []? dns-config.cfg Configure using rcp:dns-config.cfg (y/n) [n]? y / Finished network download. (134 bytes) >> >> set ip dns server 172.16.10.70 primary 172.16.10.70 added to DNS server table as primary server. >> set ip dns server 172.16.10.140 172.16.10.140 added to DNS server table as backup server. >> set ip dns enable DNS is enabled >> set ip dns domain corp.com Default DNS domain name set to corp.com Console> (enable)
This example shows how to configure the switch using a configuration file on a Flash device:
Console> (enable) copy flash config Flash device [bootflash]? Name of configuration file? test.cfg Configure using bootflash:test.cfg (y/n) [n]? y / Finished download. (10900 bytes) >> set password $1$FMFQ$HfZR5DUszVHIRhrz4h6V70 Password changed. >> set enablepass $1$FMFQ$HfZR5DUszVHIRhrz4h6V70 Password changed. >> set prompt Console> >> set length 24 default Screen length set to 24. >> set logout 20 ..... Console> (enable)
This example shows how to copy a file from a TFTP server to a Flash device:
Console> (enable) copy tftp bootflash: Address or name of remote host [172.20.22.7]? Enter source file name [cat4000-sup.4-5-1.bin]? Enter destination file name [cat4000-sup.4-5-1.bin]? 6942528 bytes available in flash, proceed (y/n) [n]?y Console> (enable)
This example shows how to download a configuration to the first startup configuration file (cfg1) on a Supervisor EngineIIG or IIIG:
Console> (enable) copy tftp cfg1 IP address or name of remote host [172.20.32.10]? Name of file to copy from [/tftpboot/my.cfg]? Download config file from /tftpboot/my.cfg to cfg1 (y/n) [n]? ......... File has been copied to cfg1. Console> (enable)
Use the delete command to delete a file on a Flash device.
delete file_id
file-id | The file to delete, where file_id is of the format [[m/]device:][filename]. m/ = The module where the Flash device is located (such as the standby supervisor engine, an FDDI module, or an ATM module). Module 1 is assumed if no module is specified. device: = Device where the file is located. Valid Flash devices are bootflash:, slot0:, and slot1:. The colon (:) is required after the device name. filename = Name of the system image or configuration file. |
cfg1 | Keyword that specifies the first startup configuration file on the Supervisor Engine II G and III G. |
cfg2 | Keyword that specifies the second startup configuration file on the Supervisor Engine II G and III G. |
This command has no default setting.
Catalyst 5000 family switches
Catalyst 4000 family switches
Catalyst 2926G series switches
Catalyst 2948G switch
Switch command.
Privileged.
This command is not supported on Catalyst 5000 family Supervisor Engine II.
These switches support only the bootflash: Flash device:
The cfg1 and cfg2 startup configuration files are present only on the Catalyst 5000 family Supervisor Engine II G and III G.
Use the undelete command to recover a deleted file.
A file cannot be undeleted if a valid file with the same name exists. Instead, you must delete the existing one first and then undelete the desired file. A file can be deleted or undeleted up to 15 times. To permanently remove all deleted files on a device, use the squeeze command.
This example shows how to delete a file from a Flash device:
Console> (enable) delete bootflash:switch_config.cfg Console> (enable)
This example shows how to delete the first startup configuration file (cfg1) on a Supervisor EngineIIG or IIIG:
Console> (enable) delete cfg1 Delete cfg1 from flash (y/n) [n]? y cfg1 has been deleted from flash Console> (enable)
dirswitch
undelete
show flash
squeeze
Use the dev command to list the device IDs available on a switch.
devThis command has no arguments or keywords.
This command has no defaults.
Catalyst 5000 family switches
Catalyst 2926G series switches
ROM monitor command.
Normal.
This example shows how to use the dev command:
rommon 4 > dev
Devices in device table:
id name
bootflash: boot flash
slot0: PCMCIA slot 0
slot1: PCMCIA slot 1
eprom: eprom
rommon 5 >
Use the dir command to list the files on a Flash device.
dir device
device | Name of the Flash device. |
This command has no defaults.
Catalyst 5000 family switches
Catalyst 4000 family switches
Catalyst 2926G series switches
Catalyst 2948G switch
ROM monitor command.
Normal.
This example shows how to list the files on a Flash device:
rommon 6 > dir bootflash:
File size Checksum File name
14086 bytes (0x3706) 0xa6a84c93 switch_config.cfg (deleted)
5415 bytes (0x1527) 0x53bbccda 5509_config.cfg
446464 bytes (0x6d000) 0x8503219d cat5000-sup3.5-1-1.bin (deleted)
4231861 bytes (0x4092b5) 0x1d6092f4 cat5000-sup3.5-2-1.bin
rommon 7 >
Use the dir command to display a list of files on a Flash device.
dir file-id [all | deleted | long]
file-id | The file on which to perform the copy action, where file_id is of the format [[m/]device:][filename]. m/ = The module where the Flash device is located (such as the standby supervisor engine, an FDDI module, or an ATM module). Module 1 is assumed if no module is specified. device: = Device where the file is located. Valid Flash devices are bootflash:, slot0:, and slot1:. You can also specify tftp: as the device name. The colon (:) is required after the device name. filename = Name of the system image or configuration file. |
all | (Optional) Keyword to display all files on the device, including deleted files. |
deleted | (Optional) Keyword to display only deleted files. |
long | (Optional) Keyword to display files that have not been deleted, in long format. |
This command has no default setting.
Catalyst 5000 family switches
Catalyst 4000 family switches
Catalyst 2926G series switches
Catalyst 2948G switch
Switch command.
Normal and privileged.
This command is not supported on the Catalyst 5000 family Supervisor Engine II.
When you omit all keywords (all, deleted, or long), the system displays file information in short format. Short format output is explained in Table 2-1.
| Column Heading | Description |
|---|---|
# | File index number |
length | File length |
date/time | Date and time the file was created |
name | Filename |
When you use one of the keywords, the system displays file information in long format. The long format is shown in Table 2-2.
| Column Heading | Description |
|---|---|
# | File index number |
ED | Letter to indicate whether the file contains an error (E) or is deleted (D) |
type | File type (1 = configuration file, 2 = image file); when the file type is unknown, the system displays a zero or FFFFFFFF in this field |
crc | File cyclic redundancy check |
seek | Offset into the file system of the next file |
nlen | Filename length |
length | File length |
date/time | Date and time the file was created |
name | Filename |
This example shows how to display the file information in short format:
Console> (enable) dir -#- -length- -----date/time------ name 2 3093399 Oct 18 1998 12:33:14 cat5000-sup3.4-5-1.bin 1428272 bytes available (6173904 bytes used) Console> (enable)
This example shows how to display the file information in long format:
Console> (enable) dir long -#- ED --type-- --crc--- -seek-- nlen -length- -----date/time------ name 2 .. ffffffff 762950d6 6234d0 25 3093399 Oct 18 1998 12:33:14 cat5000-sup3.4-5-1.bin 1428272 bytes available (6173904 bytes used) Console> (enable)
This example shows the file with index number 1 deleted:
Console> (enable) dir all -#- ED --type-- --crc--- -seek-- nlen -length- -----date/time------ name 1 .D ffffffff 5415406e 3300b8 25 3080247 Jun 12 1998 13:22:46 cat5000-sup3.4-5-1.bin 2 .. ffffffff 762950d6 6234d0 25 3093399 Oct 18 1998 12:33:14 cat5000-sup3.4-5-1.bin 1428272 bytes available (6173904 bytes used) Console> (enable)
Use the disable command to return to normal mode from privileged mode.
disableThis command has no arguments or keywords.
This command has no default setting.
Catalyst 5000 family switches
Catalyst 4000 family switches
Catalyst 2926G series switches
Catalyst 2948G switch
Switch command.
Privileged.
This example shows how to return to normal mode:
Console> (enable) disable Console>
Use the disconnect command to close an active console port or Telnet session.
disconnect {ip_addr | console}
ip_addr | Source IP address or IP alias of the session to disconnect; in dot notation, for example, 101.102.103.104. |
console | Keyword used to clear an active session on the console port. |
This command has no default setting.
Catalyst 5000 family switches
Catalyst 4000 family switches
Catalyst 2926G series switches
Catalyst 2948G switch
Switch command.
Privileged.
If multiple sessions from the same IP address exist, the system checks if the current session originated from the specified IP address. If the session did not originate from the specified IP address, all Telnet sessions from the address are disconnected. If the session does originate from the specified address, all sessions, other than the current session, are disconnected. The system prompts whether to disconnect the current Telnet session. You can answer n and remain connected or answer y and be disconnected.
This example shows how to close a Telnet session to host 192.168.255.255 (the 1 in parenthesis indicates the number of active sessions disconnected):
Console> (enable) disconnect 192.168.255.255 Telnet session from 192.168.255.255 disconnected. (1) Console> (enable)
This example shows how to close the current console session:
Console> (enable) disconnect console Console session disconnected. Console> (enable)
Use the download command to copy a software image from a specified host to the Flash memory of the supervisor engine or a designated module.
download host file [mod_num] [rcp]
host | Name or IP address of host. |
file | Name of file to be downloaded. |
mod_num | (Optional) Number of the module to receive downloaded image. |
rcp | Keyword to copy an image from a specified host to Flash using rcp. |
serial | Keyword to specify download through the serial (console) port. |
If a module number is not specified, the image is downloaded to all modules for which the image is valid.
Catalyst 5000 family switches
Catalyst 2926G series switches
Switch command.
Privileged.
The Catalyst 5000 family and 2926G series switches support two ways to download software images to the switch:
You can only download supervisor engine software using the Kermit method.
If you are performing a serial download, you can only download a software image to the supervisor engine. You cannot download a software image to a switching module using the serial download method.
If the module number is specified, the system attempts to download the file to the specified module. If the module is a different type from the type indicated by the download header, the download fails. If the module number is not specified, the file is downloaded to all modules of the type specified in the download header.
To download a software image to the Catalyst 5000 family RSM, you must session to the router and use the copy command to download the software.
You can download a software image to the Catalyst 5000 family RSFC by specifying the RSFC module number in the download command. However, when you download a system image to the RSFC from the switch CLI, the image is stored in RAM only. To permanently store the system image on the RSFC, you must session to the RSFC and use the copy command to copy the software.
In software release 5.2 and later, the download command performs the following actions automatically on switches that support the Flash file system:
The download serial command uses the Kermit protocol through the serial EIA/TIA-232 console port. The download serial command is not allowed from a console session (the console port must be available for the serial download).
| Caution After starting the serial download using Kermit, do not attempt to abort the serial download by pressing Ctrl-C. Pressing Ctrl-C interrupts the download process and might leave the switch in a problematic state. If this occurs, reboot the switch. |
This example shows how to download the c5000_spv11.bin file from the mercury host to the supervisor engine module (by default):
Console> (enable) download mercury c5000_spv11.bin Download image c5000_spv11.bin from mercury to module 1FLASH (y/n) [n]? y \ Finished network single module download. (2418396 bytes) FLASH on Catalyst: Type Address Location Intel 28F008 20000000 NMP (P3) 4MB SIM Erasing flash sector...done. Programming flash sector...done. Erasing flash sector...done. Programming flash sector...done. The system needs to be reset to run the new image. Console> (enable)
This example shows how to download the fddi_1113.cpi file from the mercury host to module 4:
Console> (enable) download mercury fddi_1113.cpi 4 This command will reset Module 4. Download image fddi_1113.cbi from mercury to Module 4 FLASH (y/n) [n]? y | Finished network download. (1064876 bytes) ...............................................................................n Console> (enable)
This example shows how to use the download command on a Catalyst 5000 family Supervisor Engine III to automatically delete files as necessary and squeeze bootflash:, copy a software image from a TFTP server, and prepend the new image filename to the BOOT variable:
Console> (enable) download 172.20.52.3 cat5000-sup3.5-2-1.bin Download image cat5000-sup3.5-2-1.bin from 172.20.52.3 to Module 1 FLASH (y/n) [n]? y Squeeze bootflash in progress.... Erasing squeeze log CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC File has been copied successfully. Console> (enable)
This example shows how to download the c5000_spv11.bin file from the mercury host to the supervisor engine module:
Console> (enable) download mercury c5000_spv11.bin rcp Download image c5000_spv11.bin from mercury to module 1FLASH (y/n) [n]? y \ Finished network single module download. (2418396 bytes) FLASH on Catalyst: Type Address Location Intel 28F008 20000000 NMP (P3) 4MB SIM Erasing flash sector...done. Programming flash sector...done. Erasing flash sector...done. Programming flash sector...done. The system needs to be reset to run the new image. Console> (enable)
This sample session shows how to connect to a remote terminal from a Sun workstation and how to use the download serial command to copy a software image to the supervisor engine module:
[At local Sun workstation]
host% kermit
C-Kermit 5A(172) ALPHA, 30 Jun 95, SUNOS 4.0 (BSD)
Type ? or 'help' for help
C-Kermit> set line /dev/ttyb
C-Kermit> c
Connecting to /dev/ttyb, speed 9600.
The escape character is ^(ASCII 28).
Type the escape character followed by C to get back,
or followed by ? to see other options.
Console> enable
Enter Password:
Console> (enable) set system baud 19200
^\C
[Back at local Sun workstation]
C-Kermit> set speed 19200
/dev/ttyb, 19200 bps
C-Kermit> c
Connecting to /dev/ttyb, speed 19200.
The escape character is ^(ASCII 28).
Type the escape character followed by C to get back,
or followed by ? to see other options.
Console> (enable) download serial
Download Supervisor image via console port (y/n) [n]? y
Concentrator Boot ROM (Ver 1.00)
Waiting for DOWNLOAD!!
Return to your local Machine by typing its escape sequence
Issue Kermit send command from there[ Send `Filename`]
^\C
[Back at Local System]
C-Kermit> send c5000_xx.bin
SF
c5000_xx.bin => C5000_XX.BIN, Size: 1233266
X to cancel file, CR to resend current packet
Z to cancel group, A for status report
E to send Error packet, Ctrl-C to quit immediately:...................................
......................................................................................
...... [OK]
ZB
C-Kermit> quit
host%
Use the download vmps command to download VMPS database information from a TFTP server.
download vmps mod [rcp]
mod | Number of the module to receive downloaded image. |
rcp | Keyword to copy an image from a specified host to Flash using rcp. |
There is no default setting for this command.
Catalyst 5000 family switches
Catalyst 2926G series switch
Switch command.
Privileged.
Before you can execute the download vmps command successfully, you must use the set vmps downloadserver command to configure the IP address of the TFTP server and the name of the VMPS configuration file on that server. If the IP address of the TFTP server is not configured, the download vmps command reports an error. If the configuration filename is not configured, the download vmps command uses the default filename vmps-config-database.1.
After a successful download, the new VMPS information replaces any existing information. If there are not enough resources to build the new configuration database, the VMPS is made inactive.
This example shows the download vmps command and typical system responses:
Console> (enable) download vmps Re-initialization of Vlan Membership Policy Server with the downloaded configuration file is in progress. 6/14/1998,17:37:29:VMPS-2:PARSER: 82 lines parsed, Errors 0
Posted: Tue Oct 5 10:56:01 PDT 1999
Copyright 1989-1999©Cisco Systems Inc.