Table of Contents

Understanding SNMP
SNMP Default Configuration
Configuring SNMP from a Network Management System
Configuring SNMP from the CLI
Using CiscoWorks2000

Configuring SNMP

This chapter describes how to configure the Simple Network Management Protocol (SNMP) on the Catalyst 5000, 4000, 2948G, and 2926G series switches.

• Understanding SNMP

• SNMP Default Configuration

• Configuring SNMP from a Network Management System

• Configuring SNMP from the CLI

• Using CiscoWorks2000

Understanding SNMP

The components of SNMP network management fall into three categories:

• Managed devices (such as a switch)

• SNMP agents and management information bases (MIBs), including Remote Monitoring (RMON) MIBs, which run on managed devices

• SNMP management applications, such as CiscoWorks2000, which communicate with agents to get statistics and alerts from the managed devices

---

Note An SNMP management application, together with the computer it runs on, is called a network management system (NMS).

---

SNMP network management uses these SNMP agent functions:

• Accessing a MIB variable---This function is initiated by the SNMP agent in response to a request from the NMS. The agent retrieves the value of the requested MIB variable and responds to the NMS with that value.

• Setting a MIB variable---This function is also initiated by the SNMP agent in response to a message from the NMS. The SNMP agent changes the value of the MIB variable to the value requested by the NMS.

• SNMP trap---This function is used to notify an NMS that a significant event has occurred at an agent. When a trap condition occurs, the SNMP agent sends an SNMP trap message to any NMSs specified as the trap receivers, under the following conditions:

  • When a port or module goes up or down

  • When temperature limitations are exceeded

  • When there are spanning-tree topology changes

  • When there are authentication failures

  • When power supply errors occur

• SNMP community strings---SNMP community strings authenticate access to MIB objects and function as embedded passwords:

  • Read-only---Gives read access to all objects in the MIB except the community strings, but does not allow write access

  • Read-write---Gives read and write access to all objects in the MIB, but does not allow access to the community strings

  • Read-write-all---Gives read and write access to all objects in the MIB, including the community strings

• SNMP traps (see the "Configuring SNMP from the CLI" section)

• RMON in the supervisor engine module software (see "Configuring RMON")

• RMON and RMON2 on a Network Analysis Module (see "Configuring the Network Analysis Module")

• RMON and RMON2 on an external SwitchProbe device

SNMP Default Configuration

Table 31-1 describes the SNMP default configuration.

Table 31-1: SNMP Default Configuration

Feature	Default Setting
SNMP community strings	Read-Only: Public Read-Write: Private Read-Write-all: Secret
SNMP trap receiver	None configured
SNMP traps	None enabled

Configuring SNMP from a Network Management System

To configure SNMP from a NMS, refer to the NMS documentation (see the "Using CiscoWorks2000" section).

The switch supports up to 20 trap receivers through the RMON2 trap destination table. Configure the RMON2 trap destination table from the NMS.

Configuring SNMP from the CLI

To configure SNMP from the command-line interface (CLI), perform this task in privileged mode:

Task	Command
Step 1 Define the SNMP community strings for each access type.	set snmp community read-only community_string set snmp community read-write community_string set snmp community read-write-all community_string
Step 2 Assign a trap receiver and community. You can specify up to ten trap receivers.	set snmp trap rcvr_address rcvr_community
Step 3 Specify the SNMP traps to send to the trap receiver.	set snmp trap enable [all | module | chassis | bridge | repeater | auth | vtp | ippermit | vmps | config | entity | stpx]
Step 4 Verify the SNMP configuration.	show snmp

This example shows how to define community strings, assign a trap receiver, and specify which traps to send to the trap receiver:

Console> (enable) set snmp community read-only Everyone
SNMP read-only community string set to 'Everyone'.
Console> (enable) set snmp community read-write Administrators
SNMP read-write community string set to 'Administrators'.
Console> (enable) set snmp community read-write-all Root
SNMP read-write-all community string set to 'Root'.
Console> (enable) set snmp trap 172.16.10.10 read-write
SNMP trap receiver added.
Console> (enable) set snmp trap 172.16.10.20 read-write-all
SNMP trap receiver added.
Console> (enable) set snmp trap enable all
All SNMP traps enabled.
Console> (enable) show snmp
RMON:                       Disabled
Extended RMON:              Extended RMON module is not present
Traps Enabled: 
Port,Module,Chassis,Bridge,Repeater,Vtp,Auth,ippermit,Vmps,config,entity,stpx
Port Traps Enabled: 1/1-2,4/1-48,5/1
Community-Access     Community-String    
----------------     --------------------
read-only            Everyone
read-write           Administrators
read-write-all       Root
Trap-Rec-Address                           Trap-Rec-Community
----------------------------------------   --------------------
172.16.10.10                               read-write
172.16.10.20                               read-write-all
Console> (enable)

Using CiscoWorks2000

CiscoWorks2000 is a family of Web-based and management platform-independent products for managing Cisco enterprise networks and devices. CiscoWorks2000 includes Resource Manager Essentials and CWSI Campus, which allow you to deploy, configure, monitor, manage, and troubleshoot a switched internetwork. For more information, see the following publications:

Posted: Mon Jul 19 12:51:24 PDT 1999
Copyright 1989-1999©Cisco Systems Inc.