|
|
This chapter describes how to check switch port status and connectivity on the Catalyst 5000, 4000, 2948G, and 2926G series switches.
This chapter consists of these sections:
The Catalyst 5000, 4000, 2948G, and 2926G series switches are multimodule systems. You can see what modules are installed, as well as the MAC address ranges and version numbers for each module, using the show module [mod_num] command. Specify a particular module number to see detailed information on that module.
The Catalyst 4912G, 2948G, and 2926G series switches are fixed-configuration switches, but are logically modular. You must apply configuration commands to the appropriate module. For example, on a Catalyst 2926G series switch, the 24 Fast Ethernet ports belong logically to module 2.
This example shows how to check module status on a Catalyst 5000 series switch. The output shows that there are two supervisor engine modules (one in standby mode), four additional modules (including an RSM/VIP2 in slots 4 and 5 and a two-slot 10BaseT Ethernet module in slots 9 and 10), and a LightStream 1010 ATM ASP installed in the chassis.
Console> (enable) show module Mod Slot Ports Module-Type Model Status --- ---- ----- ------------------------- ------------------- -------- 1 1 4 100BaseFX MMF Supervisor WS-X5530 ok 2 2 4 100BaseFX MMF Supervisor WS-X5530 standby 4 4 Route Switch Ext Port 5 5 1 Route Switch WS-X5302 ok 7 7 1 Network Analysis/RMON WS-X5380 ok 8 8 1 MM OC-3 ATM WS-X5155 ok 9 9 10/100BaseTX Ethernet Ext WS-X5238 10 10 48 10/100BaseTX Ethernet WS-X5238 ok 13 13 ASP/SRP Mod Module-Name Serial-Num --- ------------------- -------------------- 1 00007451586 2 00012114992 4 5 00007460757 7 00008175475 8 00003414855 9 00011578014 10 00011578014 Mod MAC-Address(es) Hw Fw Sw --- -------------------------------------- ------ ---------- ----------------- 1 00-e0-4f-ac-b0-00 to 00-e0-4f-ac-b3-ff 1.3 3.1.2 5.1(1) 1 00-e0-1e-9b-2e-00 to 00-e0-1e-9b-31-ff 1.3 3.1.2 5.1(1) 5 00-e0-1e-91-d5-14 to 00-e0-1e-91-d5-15 5.0 20.7 11.3(3a)WA4(5) 7 00-e0-14-10-18-00 0.100 4.1.1 4.3(0.31) 8 00-e0-1e-a9-20-b9 1.2 1.3 3.2(7) 10 00-50-0f-08-c3-f0 to 00-50-0f-08-c4-1f 0.1 5.3(1)B 5.1(1) Mod Sub-Type Sub-Model Sub-Serial Sub-Hw --- -------- --------- ---------- ------ 1 NFFC WS-F5521 0011462777 1.1 1 uplink WS-U5538 0011464723 2.0 2 NFFC WS-F5521 0008936340 1.1 2 uplink WS-U5538 0007464204 2.0 Console> (enable)
This example shows how to check module status on a Catalyst 2948G series switch. On the Catalyst 4912G and Catalyst 2948G series switches, there are two logical modules but both are in slot 1.
Console> (enable) show module Mod Slot Ports Module-Type Model Status --- ---- ----- ------------------------- ------------------- -------- 1 1 0 Switching Supervisor WS-X2948 ok 2 1 50 10/100/1000 Ethernet WS-X2948G ok Mod Module-Name Serial-Num --- ------------------- -------------------- 1 Supervisor JAB023807H1 2 Switch Ports JAB023807H1 Mod MAC-Address(es) Hw Fw Sw --- -------------------------------------- ------ ---------- ----------------- 1 00-50-73-12-09-00 to 00-50-73-12-0c-ff 1.0 4.4(1) 5.1(1) 2 00-50-73-12-0c-9e to 00-50-73-12-0c-fd 1.0 Console> (enable)
This example shows how to check module status on a specific module:
Console> (enable) show module 4 Mod Slot Ports Module-Type Model Status --- ---- ----- ------------------------- ------------------- -------- 4 4 12 100BaseFX MM Ethernet WS-X5201R ok Mod Module-Name Serial-Num --- ------------------- -------------------- 4 Backbone Links 00007285650 Mod MAC-Address(es) Hw Fw Sw --- -------------------------------------- ------ ---------- ----------------- 4 00-e0-1e-38-48-cc to 00-e0-1e-38-48-d7 0.2 4.1(0.53-E 5.1(1) Console> (enable)
You can see summary or detailed information on the switch ports using the show port [mod_num[/port_num]] command. To see summary information on all of the ports on the switch, enter the show port command with no arguments. Specify a particular module number to see information on the ports on that module only. Enter both the module number and the port number to see detailed information about the specified port.
The Catalyst 4912G, 2948G, and 2926G series switches are fixed-configuration switches, but are logically modular. To apply configuration commands to a particular port, you must specify the appropriate logical module. For more information, see the "Checking Module Status" section.
This example shows how to see information on the ports on a specific module only:
Console> (enable) show port 3
Port Name Status Vlan Level Duplex Speed Type
----- ------------------ ---------- ---------- ------ ------ ----- ------------
3/1 connected 10 normal full 1000 1000BaseSX
3/2 connected 10 normal full 1000 1000BaseSX
3/3 connected 20 normal full 1000 1000BaseSX
3/4 connected 40 normal full 1000 1000BaseSX
3/5 notconnect 1 normal full 1000 No GBIC
3/6 notconnect 1 normal full 1000 No GBIC
Port Security Secure-Src-Addr Last-Src-Addr Shutdown Trap IfIndex
----- -------- ----------------- ----------------- -------- -------- -------
3/1 disabled No disabled 15
3/2 disabled No disabled 16
3/3 disabled No disabled 17
3/4 disabled No disabled 18
3/5 disabled No disabled 19
3/6 disabled No disabled 20
Port Send FlowControl Receive FlowControl RxPause TxPause Unsupported
admin oper admin oper opcodes
----- -------- -------- -------- -------- ------- ------- -----------
3/1 desired on desired on 0 0 0
3/2 desired on desired on 0 0 0
3/3 desired on desired on 0 0 0
3/4 desired on desired on 0 0 0
3/5 desired off off off 0 0 0
3/6 desired off off off 0 0 0
Port Status Channel Channel Neighbor Neighbor
mode status device port
----- ---------- --------- ----------- ------------------------- ----------
3/1 connected off not channel
3/2 connected off not channel
3/3 connected off not channel
3/4 connected off not channel
3/5 notconnect off not channel
3/6 notconnect off not channel
Port Align-Err FCS-Err Xmit-Err Rcv-Err UnderSize
----- ---------- ---------- ---------- ---------- ---------
3/1 - 0 0 0 0
3/2 - 0 0 0 0
3/3 - 0 0 0 0
3/4 - 0 0 0 0
3/5 - 0 0 0 0
3/6 - 0 0 0 0
Port Single-Col Multi-Coll Late-Coll Excess-Col Carri-Sen Runts Giants
----- ---------- ---------- ---------- ---------- --------- --------- ---------
3/1 0 0 0 0 0 0 0
3/2 0 0 0 0 0 0 0
3/3 0 0 0 0 0 0 0
3/4 0 0 0 0 0 0 0
3/5 0 0 0 0 0 0 0
3/6 0 0 0 0 0 0 0
Last-Time-Cleared
--------------------------
Fri Apr 30 1999, 18:54:17
Console> (enable)
This example shows how to see information on an individual port:
Console> (enable) show port 2/1
Port Name Status Vlan Level Duplex Speed Type
----- ------------------ ---------- ---------- ------ ------ ----- ------------
2/1 connected trunk normal full 1000 1000BaseSX
Port Security Secure-Src-Addr Last-Src-Addr Shutdown Trap IfIndex
----- -------- ----------------- ----------------- -------- -------- -------
2/1 disabled No disabled 9
Port Send FlowControl Receive FlowControl RxPause TxPause Unsupported
admin oper admin oper opcodes
----- -------- -------- -------- -------- ------- ------- -----------
2/1 desired off off off 0 0 0
Port Status Channel Channel Neighbor Neighbor
mode status device port
----- ---------- --------- ----------- ------------------------- ----------
2/1 connected auto not channel
Port Align-Err FCS-Err Xmit-Err Rcv-Err UnderSize
----- ---------- ---------- ---------- ---------- ---------
2/1 - 0 0 0 0
Port Single-Col Multi-Coll Late-Coll Excess-Col Carri-Sen Runts Giants
----- ---------- ---------- ---------- ---------- --------- --------- ---------
2/1 0 0 0 0 0 0 0
Last-Time-Cleared
--------------------------
Tue Dec 8 1998, 13:26:01
Console> (enable)
You can display the capabilities of any port in a switch using the show port capabilities [[mod_num][/port_num]] command.
This example shows you how to display the port capabilities for switch ports:
Console> (enable) show port capabilities 1 Model WS-X5509 Port 1/1 Type 100BaseTX Speed 100 Duplex half,full Trunk encap type ISL Trunk mode on,off,desirable,auto,nonegotiate Channel 1/1-2 Broadcast suppression percentage(0-100) Flow control no Security yes Membership static,dynamic Fast start yes Rewrite no -------------------------------------------------------------- Model WS-X5509 Port 1/2 Type 100BaseTX Speed 100 Duplex half,full Trunk encap type ISL Trunk mode on,off,desirable,auto,nonegotiate Channel 1/1-2 Broadcast suppression percentage(0-100) Flow control no Security yes Membership static,dynamic Fast start yes Rewrite no Console> (enable) show port capabilities 7/1 Model WS-X5014 Port 7/1 Type 10BaseT Speed 10 Duplex half,full Trunk encap type no Trunk mode off Channel no Broadcast suppression percentage(0-100) Flow control no Security yes Membership static,dynamic Fast start yes Rewrite no Console> (enable) show port capabilities 8 Model WS-X5155 Port 8/1 Type OC3 MMF ATM Speed 155 Duplex full Trunk encap type LANE Trunk mode on Channel no Broadcast suppression no Flow control no Security no Membership static Fast start no Rewrite no Console> (enable)
You can access the switch command-line interface (CLI) using Telnet. In addition, you can use Telnet from the switch to access other devices in the network. Up to eight simultaneous Telnet sessions are possible.
To Telnet to another device on the network from the switch, perform this task in privileged mode:
| Task | Command |
|---|---|
Open a Telnet session with a remote host. | telnet host [port] |
This example shows how to Telnet from the switch to a remote host:
Console> (enable) telnet labsparc Trying 172.16.10.3... Connected to labsparc. Escape character is '^]'. UNIX(r) System V Release 4.0 (labsparc) login:
You can display the currently active user sessions on the switch using the show user command. The command output displays all active console port and Telnet sessions on the switch.
To display the active user sessions on the switch, perform this task in privileged mode:
| Task | Command |
|---|---|
Display the currently active user sessions on the switch. | show user [noalias] |
This example shows the output of the show user command when local authentication is enabled for console and Telnet sessions (the asterisk [*] indicates the current session):
Console> (enable) show users Session User Location -------- ---------------- ------------------------- console telnet sam-pc.bigcorp.com * telnet jake-mac.bigcorp.com Console> (enable)
This example shows the output of the show user command when TACACS+ authentication is enabled for console and Telnet sessions:
Console> (enable) show users Session User Location -------- ---------------- ------------------------- console sam telnet jake jake-mac.bigcorp.com telnet tim tim-nt.bigcorp.com * telnet suzy suzy-pc.bigcorp.com Console> (enable)
This example shows how to display information about user sessions using the noalias keyword to display the IP addresses of connected hosts:
Console> (enable) show users noalias Session User Location -------- ---------------- ------------------------- console telnet 10.10.10.12 * telnet 10.10.20.46 Console> (enable)
To disconnect an active user session, perform this task in privileged mode:
| Task | Command |
|---|---|
Disconnect an active user session on the switch. | disconnect {console | ip_addr} |
This example shows how to disconnect an active console port session and an active Telnet session:
Console> (enable) show users Session User Location -------- ---------------- ------------------------- console sam telnet jake jake-mac.bigcorp.com telnet tim tim-nt.bigcorp.com * telnet suzy suzy-pc.bigcorp.com Console> (enable) disconnect console Console session disconnected. Console> (enable) disconnect tim-nt.bigcorp.com Telnet session from tim-nt.bigcorp.com disconnected. (1) Console> (enable) show users Session User Location -------- ---------------- ------------------------- telnet jake jake-mac.bigcorp.com * telnet suzy suzy-pc.bigcorp.com Console> (enable)
These sections describe how to use IP ping:
You can use IP ping to test connectivity to remote hosts. If you attempt to ping a host in a different IP subnetwork, you must define a static route to the network or have a router configured to route between those subnets.
To stop a ping in progress, press Control-C.
Ping will return one of the following responses:
To ping another device on the network from the switch, perform one of these tasks in privileged mode:
| Task | Command |
|---|---|
| ping host |
| ping -s host [packet_size] [packet_count] |
This example shows how to ping a remote host:
Console> (enable) ping labsparc labsparc is alive Console> (enable) ping 172.16.10.3 172.16.10.3 is alive Console> (enable)
This example shows how to ping a remote host using the ping options:
Console> (enable) ping -s 172.16.10.3 1000 8 PING 172.20.52.3: 1000 data bytes 1008 bytes from 172.16.10.3: icmp_seq=0. time=6 ms 1008 bytes from 172.16.10.3: icmp_seq=1. time=5 ms 1008 bytes from 172.16.10.3: icmp_seq=2. time=6 ms 1008 bytes from 172.16.10.3: icmp_seq=3. time=6 ms 1008 bytes from 172.16.10.3: icmp_seq=4. time=6 ms 1008 bytes from 172.16.10.3: icmp_seq=5. time=5 ms 1008 bytes from 172.16.10.3: icmp_seq=6. time=6 ms 1008 bytes from 172.16.10.3: icmp_seq=7. time=5 ms ----172.16.10.3 PING Statistics---- 8 packets transmitted, 8 packets received, 0% packet loss round-trip (ms) min/avg/max = 5/5/6 Console> (enable)
These sections describe how to use IP traceroute:
You can use IP traceroute to identify the path that packets take through the network on a hop-by-hop basis. The command output displays all network layer (Layer 3) devices, such as routers, that the traffic passes through on the way to the destination.
Switches can participate as the source or destination of the traceroute command but will not appear as a hop in the traceroute command output.
The traceroute command uses the Time To Live (TTL) field in the IP header to cause routers and servers to generate specific return messages. Traceroute starts by sending a User Datagram Protocol (UDP) datagram to the destination host with the TTL field set to 1. If a router finds a TTL value of 1 or 0, it drops the datagram and sends back an Internet Control Message Protocol (ICMP) time-exceeded message to the sender. The traceroute facility determines the address of the first hop by examining the source address field of the ICMP time-exceeded message.
To identify the next hop, traceroute sends a UDP packet with a TTL value of 2. The first router decrements the TTL field by 1 and sends the datagram to the next router. The second router sees a TTL value of 1, discards the datagram, and returns the time-exceeded message to the source. This process continues until the TTL is incremented to a value large enough for the datagram to reach the destination host (or until the maximum TTL is reached).
To determine when a datagram reaches its destination, traceroute sets the UDP destination port in the datagram to a very large value which the destination host is unlikely to be using. When a host receives a datagram with an unrecognized port number, it sends an ICMP port unreachable error to the source. This message indicates to the traceroute facility that it has reached the destination.
To trace the path that packets take through the network, perform this task in privileged mode:
| Task | Command |
|---|---|
Execute IP traceroute to trace the path packets take through the network. | traceroute [-n] [-w wait_time] [-i initial_ttl] [-m max_ttl] [-p dest_port] [-q nqueries] [-t tos] host [data_size] |
This example shows the basic usage of the traceroute command:
Console> (enable) traceroute 10.1.1.100 traceroute to 10.1.1.100 (10.1.1.100), 30 hops max, 40 byte packets 1 10.1.1.1 (10.1.1.1) 1 ms 2 ms 1 ms 2 10.1.1.100 (10.1.1.100) 2 ms 2 ms 2 ms Console> (enable)
This example shows how to perform a traceroute with six queries to each hop with packets of 1400 bytes each:
Console> (enable) traceroute -q 6 10.1.1.100 1400 traceroute to 10.1.1.100 (10.1.1.100), 30 hops max, 1440 byte packets 1 10.1.1.1 (10.1.1.1) 2 ms 2 ms 2 ms 1 ms 2 ms 2 ms 2 10.1.1.100 (10.1.1.100) 2 ms 4 ms 3 ms 3 ms 3 ms 3 ms Console> (enable)
Posted: Mon Jul 19 12:43:49 PDT 1999
Copyright 1989-1999©Cisco Systems Inc.