|
|
Use the shutdown command to shut down a physical interface. Use the no form of this command to restart the interface.
shutdownThis command has no arguments or keywords.
The interface is enabled.
Cisco IOS ATM command.
Interface configuration.
This command is not supported by the Catalyst 4000 and 2948G series switches.
This example shows how to access and shut down the atm0 interface:
ATM(config)#interface atm0 ATM(config-if)#shutdown ATM(config-if)#
This example shows how to access and then restart the atm0 interface:
ATM(config)#interface atm0 ATM(config-if)#no shutdown ATM(config-if)#
Use the slip command to attach or detach SLIP for the console port.
slip {attach | detach}
attach | Keyword to activate SLIP for the console port. |
detach | Keyword to deactivate SLIP for the console port. |
By default, SLIP is not active (detached).
Switch command.
Privileged.
You can enter the slip command from a console port session or a Telnet session.
This example shows how to enable SLIP for a console port during a console port session:
Console> (enable) slip attach Console port now running SLIP. <console port running SLIP>
This example shows how to disable SLIP for a console port during a Telnet session:
Console> (enable) slip detach SLIP detached on Console port. <console port back to RS-232 Console> Console> (enable)
Use the squeeze command to delete Flash files permanently.
squeeze [m/]device:
m/ | (Optional) Module number of the supervisor engine containing the Flash device. |
device: | Device where the Flash device resides. |
This command has no default setting.
Switch command.
Privileged.
A colon (:) is required after the specified device.
This command applies only to the Supervisor Engine III and Catalyst 4000 and 2948G series switch supervisor engine module. If you attempt to run this command on a Supervisor Engine I or II, you will receive an error message.
These examples show how to use the squeeze command to delete the slot0 Flash files and then use the show flash command to confirm the deletion:
Console> squeeze slot0: All deleted files will be removed, proceed (y/n) [n]?y Squeeze operation may take a while, proceed (y/n) [n]?y .......................................................... Console> show flash -#- ED --type-- --crc--- -seek-- nlen -length- -----date/time------ name 1 .. 2 43B312DF 100fc0 15 1052608 Aug 12 1998 10:23:30 cat5k_r47_1.cbi 7336000 bytes available (1052608 bytes used) Console>
Use the sscop cc-timer command to change the SSCOP connection control timer value. Use the no form of this command to restore the default value.
sscop cc-timer msecs
msecs | Number of microseconds between Begin messages. The range of msecs is 1 to 60000. |
The default SSCOP connection control timer value is 10 seconds.
Cisco IOS ATM command.
Interface configuration.
This command is not supported by the Catalyst 4000 and 2948G series switches.
The SSCOP connection control timer determines the time between transmission of SSCOP BGN, END, or RS PDUs as long as an acknowledgment has not been received.
This example shows how to set the SSCOP connection control timer value to 15 microseconds:
ATM(config-if)#sscop cc-timer 15
Use the sscop keepalive-timer command to change the SSCOP keepalive timer value. Use the no form of this command to restore the default value.
sscop keepalive-timer msecs
msecs | Number of microseconds the ATM module waits between transmission of poll PDUs when no SD or SDP PDUs are queued for transmission or are outstanding pending acknowledgments. The range of msecs is 1 to 60000. |
The default SSCOP keepalive timer value is 30 seconds.
Cisco IOS ATM command.
Interface configuration.
This command is not supported by the Catalyst 4000 and 2948G series switches.
This example shows how to set the SSCOP keepalive timer to 15 microseconds:
ATM(config-if)#sscop keepalive-timer 15
Use the sscop max-cc command to change the SSCOP connection control retry count. Use the no form of this command to restore the default value.
sscop max-cc retries
retries | Number of times that SSCOP attempts to transmit BGN (establishment), END (release), or RS (resynchronization) PDUs as long as an acknowledgment has not been received. The range of retries is 1 to 127. |
The default SSCOP connection control retry count is 10 retries.
Cisco IOS ATM command.
Interface configuration.
This command is not supported by the Catalyst 4000 and 2948G series switches.
This example shows how to set the SSCOP connection control retry count to 20:
ATM(config-if)#sscop max-cc 20
Use the sscop max-stat command to change the SSCOP number of entries in a Stat frame. Use the no form of this command to restore the default value.
sscop max-stat entries
entries | Number of entries in a Stat frame. The range of entries is 1 to 255. |
Cisco IOS ATM command.
Interface configuration.
This command is not supported by the Catalyst 4000 and 2948G series switches.
This example shows how to set the SSCOP entries in a Stat frame to 50:
ATM(config-if)#sscop max-stat 50
Use the sscop poll-timer command to change the SSCOP poll timer value. Use the no form of this command to restore the default value.
sscop poll-timer msecs
msecs | Number of microseconds the ATM module waits between transmission of POLL PDUs. The range of msecs is 1 to 60000. |
The default SSCOP poll timer value is 10 seconds.
Cisco IOS ATM command.
Interface configuration.
This command is not supported by the Catalyst 4000 and 2948G series switches.
The SSCOP poll timer controls the maximum time between transmission of POLL PDUs when SD or SDP PDUs are queued for transmission or are outstanding pending acknowledgments.
This example shows how to set the SSCOP poll timer to 15 microseconds:
ATM(config-if)#sscop poll-timer 15
Use the sscop receive-window command to change the size of the SSCOP receiver window. Use the no form of this command to restore the default value.
sscop receive-window packets
packets | Number of packets the interface receives before it sends an acknowledgment to the ATM switch. The range of packets is 1 to 127. |
The default size of the SSCOP receiver window is 7 packets.
Cisco IOS ATM command.
Interface configuration.
This command is not supported by the Catalyst 4000 and 2948G series switches.
This example shows how to set the size of the SSCOP receiver window to 10 packets:
ATM(config-if)#sscop receive-window 10
Use the sscop send-window command to change the size of the SSCOP transmitter window. Use the no form of this command to restore the default value.
sscop send-window packets
packets | Number of packets the interface can send before it must receive an acknowledgment from the ATM switch. The range of packets is 1 to 127. |
The default size of the SSCOP transmitter window is 7 packets.
Cisco IOS ATM command.
Interface configuration.
This command is not supported by the Catalyst 4000 and 2948G series switches.
This example shows how to set the size of the SSCOP transmitter window to 10 packets:
ATM(config-if)#sscop send-window 10
Use the switch command to switch the clock from the supervisor clock to the internal clock or from the active supervisor to the standby supervisor.
switch {clock | supervisor}
clock | Keyword to switch the clock from the supervisor clock to the internal clock. |
supervisor | Keyword to switch from the active supervisor to the standby supervisor (Catalyst 5500 and Catalyst 5505 switches only). |
This command has no default setting.
Switch command.
Privileged.
The switch command is supported only on Catalyst 5500 and Catalyst 5505 switches.
This example shows how to switch the clock:
Console> (enable) switch clock This command will reset system and force a clock switch-over. Do you want to continue (y/n) [n]? Console> (enable)
This example shows how to switch to the standby supervisor:
Console> (enable) switch supervisor This command will force a switch-over to the standby Supervisor module. Do you want to continue (y/n) [n]? Console> (enable)
Use the sync command to write the working in-core copy of environment variables and the aliases out to NVRAM so they are read on the next reset.
syncThis command has no arguments or keywords.
This command has no defaults.
ROM monitor command.
Normal.
This example shows how to use the sync command:
rommon 10 > sync rommon 11 >
Use the telnet command to start a Telnet connection to a remote host.
telnet host [port_num]
host | Name or IP address of the remote host to which you want to connect. |
port_num | (Optional) Specific port connection on the remote host. |
This command has no default setting.
Switch command.
Privileged.
This example shows how to open and close a Telnet session with the host elvis:
Console> (enable) telnet elvis Trying 192.122.174.11... Connected to elvis. Escape character is '^]'. UNIX(r) System V Release 4.0 (elvis) login: fred Password: Last login: Thu Jun 11 09:25:01 from forster.cisc.rum Sun Microsystems Inc. SunOS 5.4 Generic July 1994 You have new mail. % logout Console> (enable)
Use the terminal command to set the number of lines displayed on-screen. Use the no form of this command to return the screen length to the default.
terminal length [screen-length]
screen-length | (Optional) Number of lines to display on-screen. The range of screen-length is 0 to 512. A value of 0 disables pausing between screens of output. |
The default screen length is 24 lines.
Cisco IOS ATM command.
EXEC.
This command is not supported by the Catalyst 4000 and 2948G series switches.
This example shows how to set the terminal length to 0 so that output scrolls on the screen without pausing:
ATM>terminal length 0
Use the test snmp trap command to send an SNMP trap message to the trap receivers.
test snmp trap trap_num [specific_num]
trap_num | Number of the trap. |
specific_num | (Optional) Number of a predefined trap. |
This command has no default setting.
Switch command.
Privileged.
This example shows how to run trap 0:
Console> (enable) test snmp trap 0 SNMP trap message sent. (4) Console> (enable)
Use the traceroute command to display a hop-by-hop path through an IP network from the Catalyst 5000, 4000, 2948G, or 2926G series switch to a specific destination host.
traceroute [-n] [-w wait_time] [-i initial_ttl] [-m max_ttl] [-p dest_port] [-q nqueries] [-t tos] host [data_size]
-n | (Optional) Option that prevents traceroute from performing a DNS lookup for each hop on the path. Only numerical IP addresses are printed. |
-w wait_time | (Optional) Option used to specify the amount of time (in seconds) that traceroute will wait for an ICMP response message. The allowed range for wait_time is 1 to 300 seconds; the default is 5 seconds. |
-i initial_ttl | (Optional) Option that causes traceroute to send ICMP datagrams with a TTL value equal to initial_ttl instead of the default TTL of 1. This causes traceroute to skip processing for hosts that are less than initial_ttl hops away. |
-m max_ttl | (Optional) Option used to specify the maximum TTL value for outgoing ICMP datagrams. The allowed range for max_ttl is 1 to 255; the default value is 30. |
-p dest_port | (Optional) Option used to specify the base UDP destination port number used in traceroute datagrams. This value is incremented each time a datagram is sent. The allowed range for dest_port is 1 to 65535; the default base port is 33434. Use this option in the unlikely event that the destination host is listening to a port in the default traceroute port range. |
-q nqueries | (Optional) Option used to specify the number of datagrams to send for each TTL value. The allowed range for nqueries is 1 to 1000; the default is 3. |
-t tos | (Optional) Option used to specify the TOS to be set in the IP header of the outgoing datagrams. The allowed range for tos is 0 to 255; the default is 0. Use this option to see if different types of service cause routes to change. |
host | IP alias or IP address in dot notation (a.b.c.d) of the destination host. |
data_size | (Optional) Number of bytes, in addition to the default of 40 bytes, of the outgoing datagrams. The allowed range is 0 to 1420; the default is 0. |
Entering the traceroute host command without options sends three 40-byte ICMP datagrams with an initial TTL of 1, a maximum TTL of 30, a timeout period of 5 seconds, and a TOS specification of 0 to destination UDP port number 33434. For each host in the processed path, the initial TTL for each host and the destination UDP port number for each packet sent are incremented by one.
Switch command.
Privileged.
To interrupt traceroute after the command has been issued, press Ctrl-C.
The traceroute command uses the TTL field in the IP header to cause routers and servers to generate specific return messages. Traceroute starts by sending a UDP datagram to the destination host with the TTL field set to 1. If a router finds a TTL value of 1 or 0, it drops the datagram and sends back an ICMP "time exceeded" message to the sender. The traceroute facility determines the address of the first hop by examining the source address field of the ICMP time-exceeded message.
To identify the next hop, traceroute again sends a UDP packet but this time with a TTL value of 2. The first router decrements the TTL field by 1 and sends the datagram to the next router. The second router sees a TTL value of 1, discards the datagram, and returns the time-exceeded message to the source. This process continues until the TTL is incremented to a value large enough for the datagram to reach the destination host (or until the maximum TTL is reached).
To determine when a datagram has reached its destination, traceroute sets the UDP destination port in the datagram to a very large value that the destination host is unlikely to be using. When a host receives a datagram with an unrecognized port number, it sends an ICMP "port unreachable" error to the source. This message indicates to the traceroute facility that it has reached the destination.
Catalyst 5000, 4000, 2948G, or 2926G series switches can participate as the source or destination of the traceroute command. However, because they are Layer 2 devices, Catalyst 5000, 4000, 2948G, or 2926G series switches do not examine the TTL field in the IP header and therefore do not decrement the TTL field or send ICMP time-exceeded messages. Thus, a Catalyst 5000, 4000, 2948G, or 2926G series switch does not appear as a hop in the traceroute command output.
This example shows how to use the traceroute command to determine the path from the source to the destination host server10:
Console> (enable) traceroute server10 traceroute to server10.company.com (172.16.22.7), 30 hops max, 40 byte packets 1 engineering-1.company.com (172.31.192.206) 2 ms 1 ms 1 ms 2 engineering-2.company.com (172.31.196.204) 2 ms 3 ms 2 ms 3 gateway_a.company.com (172.16.1.201) 6 ms 3 ms 3 ms 4 server10.company.com (172.16.22.7) 3 ms * 2 ms Console> (enable)
Table 2-86 describes the fields in the traceroute command output.
| Field | Description |
|---|---|
30 hops max, 40 byte packets | Maximum TTL value and the size of the ICMP datagrams being sent. |
2 ms 1 ms 1 ms | Total time (in milliseconds) for each ICMP datagram to reach the router or host plus the time it took for the ICMP time-exceeded message to return to the host. An exclamation point following any of these values (for example, 20 ms !) indicates that the port-unreachable message returned by the destination had a TTL of 0 or 1. Typically, this occurs when the destination uses the TTL value from the arriving datagram as the TTL in its ICMP reply. The reply does not arrive at the source until the destination receives a traceroute datagram with a TTL equal to the number of hops between the source and destination. |
3 ms * 2 ms | "*" indicates that the timeout period (default of 5 seconds) expired before an ICMP time-exceeded message was received for the datagram. |
If traceroute receives an ICMP error message other than a time-exceeded or port-unreachable message, it prints one of the error codes shown in Table 2-87 instead of the round-trip time or an asterisk (*).
| ICMP Error Code | Meaning |
|---|---|
!N | No route to host. The network is unreachable. |
!H | No route to host. The host is unreachable. |
!P | Connection refused. The protocol is unreachable. |
!F | Fragmentation needed but do not fragment (DF) bit was set. |
!S | Source route failed. |
!A | Communication administratively prohibited. |
? | Unknown error occurred. |
Use the unalias command to remove the alias name and associated value from the alias list.
unalias name
name | Name of the alias. |
ROM monitor command.
Normal.
This example shows how to use the unalias command to remove the s alias and then check to ensure it was removed:
rommon 5 > alias r=repeat h=history ?=help b=boot ls=dir i=reset k=stack s=set rommon 6 > unalias s rommon 7 > alias r=repeat h=history ?=help b=boot ls=dir i=reset k=stack rmmon 8 > s monitor: command "s" not found ===========================================================================
Use the undelete command to recover a deleted file on a Flash memory device. The deleted file can be recovered using its index (because there could be multiple deleted files with the same name).
undelete index [[m/]device:]
index | Index number of the deleted file. |
m/ | (Optional) Module number of the supervisor engine containing the Flash device. |
device: | (Optional) Device where the Flash device resides. |
This command has no default setting.
Switch command.
Privileged.
A colon (:) is required after the specified device.
Use the dir command to learn the index number of the file to be undeleted.
A file cannot be undeleted if a valid file with the same name exists. You must delete the existing file before you can undelete the target file.
A file can be deleted and undeleted up to 15 times.
To delete all deleted files permanently on a device, use the squeeze command.
This example shows how to recover the deleted file with index 1 and use the show flash command to confirm:
Console> (enable) undelete 1 bootflash: Console> (enable) show flash-#- ED --type-- --crc--- -seek-- nlen -length- -----date/time------ name1 .. ffffffff a638976e 3627ec 23 3286891 Jan 01 1999 07:04:37 cat5000-supn2 .. ffffffff a6a84c93 365f74 17 14086 Jan 29 1999 02:33:56 switch_confg3 .. ffffffff 141a9127 70b7cc 29 3823575 Mar 09 1999 19:15:55 cat5000-supn1428272 bytes available (6173904 bytes used) Console> (enable)
Use the unset=varname command to remove a variable name from the variable list.
unset=varnameThis command has no arguments or keywords.
This command has no defaults.
ROM monitor command.
Normal.
This example shows how to use the set command to display the variable list, use the unset command to remove a variable name from the variable list, and then use the set command to display the variable list to verify:
rommon 2 > set PS1=rommon ! > BOOT= ?=0 rommon 3 > unset=0 rommon 4 > set PS1=rommon ! > BOOT=
Use the upload command to upload a software image to a network host.
upload host file [mod_num]
host | IP address or IP alias of the host. |
file | Name of the image file. |
mod_num | (Optional) Number of the module from which to upload the image file. If no number is specified, the default is module 1. |
This command has no default setting.
Switch command.
Privileged.
To upload a software image for the RSM, use the session command.
This command is not supported by the three-port Gigabit Ethernet switching module (WS-X5403).
This example shows how to upload the supervisor image to the c5009_11.bin file on the mercury host:
Console> (enable) upload mercury c5009_11.bin 3 Upload Module 1 image to c5009_11.bin on mercury (y/n) [n]? y / Done. Finished Network Upload. (153908 bytes) Console> (enable)
Use the varname= command to set the variable VARNAME to varvalue. Note that the syntax varname= sets the variable to a NULL string.
varname=value
varname= | Name of the variable. |
value | Any ROM monitor command. |
This command has no defaults.
ROM monitor command.
Normal.
Do not put a space before or after the equal (=) sign. If there are spaces, you must place the value in quotes. Spell out variable names in all caps to make them conspicuous.
This example shows how to assign a variable name to a value:
rommon 1 > s=set rommon 2 > s PS1=rommon ! > BOOT= ?=0
Use the verify command to confirm the checksum of a file on a Flash device.
verify [[m/]device:] filename
m/ | (Optional) Module number of the supervisor engine containing the Flash device. |
device: | (Optional) Device where the Flash device resides. |
filename | Name of the configuration file. |
This command has no default setting.
Switch command.
Privileged.
A colon (:) is required after the specified device.
This example shows how to use the verify command:
Console> verify cat5k_r47_1.cbi .......................................................... File cat5k_r47_1.cbi verified OK.
Use the wait command to cause the CLI to pause for a specified number of seconds before executing the next command. This command might be included in a configuration file.
wait seconds
seconds | Number of seconds for the CLI to wait. |
This command has no default setting.
Switch command.
Normal.
This example shows how to pause the CLI for 5 seconds:
Console> wait 5 Console>
Use the whichboot command to determine which file booted.
whichbootThis command has no arguments or keywords.
This command has no default setting.
Switch command.
Privileged.
This command applies only to the Supervisor Engine III and Catalyst 4000 and 2948G series switch supervisor engine module. If you attempt to run this command on a Supervisor Engine I or II, you will receive an error message.
This example shows how to use the whichboot command:
Console> whichbootBoot image name is 'bootflash:cat5000-sup3.5-1-0-59.bin'.Console>
Use the write command to upload the current configuration to a host or display it on the terminal.
write {host file | network | terminal}
host | IP address or IP alias of the host. |
file | Name of the configuration file. |
Keyword to specify interactive prompting for the IP address or IP alias of the host and the filename to upload. | |
terminal | Keyword to display the configuration file on the terminal. |
This command has no default setting.
Switch command.
Privileged.
The write terminal command is exactly the same as the show config command. The write host file command is a shorthand version of the write network command.
The write terminal command is equivalent to the ATM command write terminal.
You cannot use the write network command to upload software to the ATM module.
With the write network command, the file must already exist on the host (use the UNIX touch filename command to create it).
This sample session assumes that module 1 is a 2-port supervisor module, module 2 is a 12-port 10/100BaseT switched Ethernet module, modules 3 and 5 are empty, and module 4 is an FDDI module. Details of the ATM configuration must be accessed through the special module mode.
This example shows how to upload the system5.cfg file to the mercury host using the write network command:
Console> (enable) write network IP address or name of host? mercury Name of configuration file to write? system5.cfg Upload configuration to system5.cfg on mercury (y/n) [y]? y / Done. Finished Network Upload. (9003 bytes) Console> (enable)
This example shows how to upload the system5.cfg file to the mercury host using the write host file command as a shorthand method:
Console> (enable) write mercury system5.cfg Upload configuration to system5.cfg on mercury (y/n) [y]? y / Done. Finished Network Upload. (9003 bytes) Console> (enable)
This example shows how to use the write terminal command to display the configuration file on the terminal:
Console> (enable) write terminal begin set password $1$FMFQ$HfZR5DUszVHIRhrz4h6V70 set enablepass $1$FMFQ$HfZR5DUszVHIRhrz4h6V70 set prompt Console> ! #system set system baud 9600 set system modem disable set system name set system location set system contact ! #snmp set snmp community read-only public set snmp community read-write private set snmp community read-write-all secret set snmp trap disable ! #vlan/trunk set vlan 1 1/1-2,4/1 set vlan 2 2/1-5 ! #trunks ! #cam set cam agingtime 1 300 set cam agingtime 2 300 ! #ip set interface sc0 0.0.0.0 0.0.0.0 0.0.0.0 set interface sl0 0.0.0.0 0.0.0.0 set ip redirect enable set ip unreachable disable set ip fragmentation enable set ip alias default 0.0.0.0 set arp agingtime 1200 ! #bridge set bridge ipx snaptoether 8023raw set bridge ipx 8022toether 8023 set bridge ipx 8023rawtofddi snap ! #Command alias ! #cdp set cdp enable 1/1-2,2/1-5,4/1 set cdp interval 1/1 60 set cdp interval 1/2 60 set cdp interval 2/1 60 set cdp interval 2/2 60 set cdp interval 2/3 60 set cdp interval 2/4 60 set cdp interval 2/5 60 set cdp interval 4/1 60 ! #spantree #vlan 1 set spantree enable 1 set spantree fwddelay 15 1 set spantree hello 2 1 set spantree maxage 20 1 set spantree priority 32768 1 set spantree portpri 1/1 32 set spantree portcost 1/1 10 set spantree portpri 1/2 32 set spantree portcost 1/2 10 set spantree portpri 4/1 32 set spantree portcost 4/1 10 #vlan 2 set spantree enable 2 set spantree fwddelay 15 2 set spantree hello 2 2 set spantree maxage 20 2 set spantree priority 32768 2 set spantree portpri 2/1 32 set spantree portcost 2/1 100 set spantree portpri 2/2 32 set spantree portcost 2/2 100 set spantree portpri 2/3 32 set spantree portcost 2/3 100 set spantree portpri 2/4 32 set spantree portcost 2/4 100 set spantree portpri 2/5 32 set spantree portcost 2/5 100 ! #trunk ! #module 1 set module name 1 set port enable 1/1 set port name 1/1 set port duplex 1/1 half set port level 1/1 normal set port enable 1/2 set port name 1/2 set port duplex 1/2 half set port level 1/2 normal ! #module 2 set module name 2 set module enable 2 ! set port enable 2/1 set port name 2/1 set port duplex 2/1 half set port level 2/1 normal set port enable 2/2 set port name 2/2 set port duplex 2/2 half set port level 2/2 normal set port enable 2/3 set port name 2/3 set port duplex 2/3 half set port level 2/3 normal set port enable 2/4 set port name 2/4 set port duplex 2/4 half set port level 2/4 normal set port enable 2/5 set port name 2/5 set port duplex 2/5 half set port level 2/5 normal ! #module 3 empty ! #module 4 set module name 4 set module enable 4 ! set fddi userdata 4 WorkGroup Stack set fddi tnotify 4 30 set fddi treq 4 5000 set port enable 4/1 set port name 4/1 set port level 4/1 normal set fddi tlmin 4/1 40 set port enable 4/2 set port name 4/2 set port level 4/2 normal set fddi tlmin 4/2 40 ! #module 5 empty end Console> (enable)
show config
copy config
Use the write erase command to erase the configuration information in NVRAM. The NVRAM is then filled with the default configuration.
write eraseThis command has no arguments or keywords.
Switch command.
Privileged.
This command is not supported by the Catalyst 4000 and 2948G series switches.
This example shows how to erase the configuration in nonvolatile memory:
Console> (enable) write erase
Use the write memory command to copy the configuration information in running memory to NVRAM.
write memoryThis command has no arguments or keywords.
Switch command.
Privileged.
If you enter the write memory command from a bootstrap system image, a warning displays that the previous NVRAM configuration will be overwritten and some of the configuration commands will be lost unless you answer no. This warning is not displayed if NVRAM does not contain a valid configuration or if the previous configuration in NVRAM was generated by a bootstrap system image.
This example shows how to copy the current configuration information to NVRAM:
Console> (enable) write memory ###[OK]
Use the write terminal command to display the configuration information currently in running memory.
write terminalThis command has no arguments or keywords.
Switch command.
Privileged.
You can also use this command in ATM EXEC mode to display the current ATM configuration information. This usage is not supported by the Catalyst 4000 and 2948G series switches.
This example shows how to display the current system configuration information:
Console> (enable) write terminal ..... begin set password $1$FMFQ$HfZR5DUszVHIRhrz4h6V70 set enablepass $1$FMFQ$HfZR5DUszVHIRhrz4h6V70 set prompt Cat5500> set length 24 default set logout 20 set banner motd ^C^C ! #system set system baud 9600 set system modem disable set system name set system location set system contact ! #snmp set snmp community read-only public set snmp community read-write public set snmp community read-write-all secret set snmp rmon disable set snmp trap disable module set snmp trap disable chassis set snmp trap disable bridge set snmp trap disable repeater set snmp trap disable vtp set snmp trap disable auth set snmp trap disable ippermit set snmp trap disable vmps set snmp trap disable entity set snmp trap disable config set snmp trap disable stpx ! #ip set interface sc0 524 172.20.52.100 255.255.255.224 172.20.52.127 set interface sc0 up set interface sl0 0.0.0.0 0.0.0.0 set interface sl0 up set arp agingtime 1200 set ip redirect enable set ip unreachable enable set ip fragmentation enable set ip route 0.0.0.0 172.20.52.97 1 set ip alias default 0.0.0.0 ! #Command alias ! #vmps set vmps server retry 3 set vmps server reconfirminterval 60 set vmps tftpserver 0.0.0.0 vmps-config-database.1 set vmps state disable ! #dns set ip dns server 171.68.10.70 primary set ip dns server 171.68.10.140 set ip dns server 171.68.10.132 set ip dns enable set ip dns domain cisco.com ! #tacacs+ set tacacs attempts 3 set tacacs directedrequest disable set tacacs timeout 5 set authentication login tacacs disable set authentication login local enable set authentication enable tacacs disable set authentication enable local enable ! #bridge set bridge ipx snaptoether 8023raw set bridge ipx 8022toether 8023 set bridge ipx 8023rawtofddi snap ! #vtp set vtp domain Lab_Network set vtp mode server set vtp v2 disable set vtp pruning disable set vtp pruneeligible 2-1000 clear vtp pruneeligible 1001-1005 set vlan 1 name default type ethernet mtu 1500 said 100001 state active set vlan 521 name VLAN0521 type ethernet mtu 1500 said 100521 state active set vlan 522 name VLAN0522 type ethernet mtu 1500 said 100522 state active set vlan 523 name VLAN0523 type ethernet mtu 1500 said 100523 state active set vlan 524 name VLAN0524 type ethernet mtu 1500 said 100524 state active set vlan 1002 name fddi-default type fddi mtu 1500 said 101002 state active set vlan 1004 name fddinet-default type fddinet mtu 1500 said 101004 state activ e bridge 0x0 stp ieee set vlan 1005 name trnet-default type trbrf mtu 1500 said 101005 state active br idge 0x0 stp ibm set vlan 1003 name token-ring-default type trcrf mtu 1500 said 101003 state acti ve parent 0 ring 0x0 mode srb aremaxhop 0 stemaxhop 0 set interface sc0 524 172.20.52.100 255.255.255.224 172.20.52.127 ! #spantree #uplinkfast groups set spantree uplinkfast disable #backbonefast set spantree backbonefast disable #vlan 1 set spantree enable 1 set spantree fwddelay 15 1 set spantree hello 2 1 set spantree maxage 20 524 set spantree priority 32768 524 #vlan 1003 set spantree enable 1003 set spantree fwddelay 4 1003 set spantree hello 2 1003 set spantree maxage 10 1003 set spantree priority 32768 1003 set spantree portstate 1003 auto 0 set spantree portcost 1003 62 set spantree portpri 1003 4 set spantree portfast 1003 disable #vlan 1005 set spantree enable 1005 set spantree fwddelay 4 1005 set spantree hello 2 1005 set spantree maxage 10 1005 set spantree priority 32768 1005 set spantree multicast-address 1005 ieee ! #cgmp set cgmp disable set cgmp leave disable ! #syslog set logging console enable set logging server disable set logging level cdp 2 default set logging level mcast 2 default set logging level disl 5 default set logging level dvlan 2 default set logging level earl 2 default set logging level fddi 2 default set logging level ip 2 default set logging level pruning 2 default set logging level snmp 2 default set logging level spantree 2 default set logging level sys 5 default set logging level tac 2 default set logging level tcp 2 default set logging level telnet 2 default set logging level tftp 2 default set logging level vtp 2 default set logging level vmps 2 default set logging level kernel 2 default set logging level filesys 2 default set logging level drip 2 default set logging level pagp 5 default set logging level mgmt 5 default set logging level mls 5 default set logging level protfilt 2 default ! #ntp set ntp broadcastclient disable set ntp broadcastdelay 3000 set ntp client disable clear timezone set summertime disable ! #permit list set ip permit disable ! #drip set tokenring reduction enable set tokenring distrib-crf disable ! #igmp set igmp disable ! #module 1 : 2-port 100BaseTX Supervisor set module name 1 set vlan 1 1/2 set vlan 524 1/1 set port channel 1/1-2 off set port channel 1/1-2 auto set port enable 1/1-2 set port level 1/1-2 normal set port duplex 1/1 full set port duplex 1/2 half set port trap 1/1-2 disable set port name 1/1 Backbone 5000 Link set port name 1/2 set port security 1/1-2 disable set port broadcast 1/1-2 100% set port membership 1/1-2 static set cdp enable 1/1-2 set cdp interval 1/1-2 60 set trunk 1/1 auto isl 1-1005 set trunk 1/2 auto isl 1-1005 set spantree portfast 1/1-2 disable set spantree portcost 1/1-2 10 set spantree portpri 1/1-2 32 set spantree portvlanpri 1/1 0 set spantree portvlanpri 1/2 0 set spantree portvlancost 1/1 cost 18 set spantree portvlancost 1/2 cost 18 ! #module 2 empty ! #module 3 : 24-port 3 Segment 100BaseTX Ethernet set module name 3 set module enable 3 set vlan 1 3/9,3/17 set port enable 3/1-24 set port level 3/1,3/9,3/17 normal set port trap 3/1-24 disable set port name 3/1-24 set port security 3/1-24 disable set port broadcast 3/1,3/9,3/17 0 set port membership 3/1 dynamic set port membership 3/9,3/17 static set cdp enable 3/1,3/9,3/17 set cdp interval 3/1,3/9,3/17 60 set spantree portfast 3/1 enable set spantree portfast 3/9,3/17 disable set spantree portcost 3/1,3/9,3/17 19 set spantree portpri 3/1,3/9,3/17 32 ! #module 4 : 1-port MM OC-3 ATM set module name 4 set port level 4/1 normal set port name 4/1 set cdp enable 4/1 set cdp interval 4/1 60 set trunk 4/1 on lane 1-1005 set spantree portcost 4/1 14 set spantree portpri 4/1 32 set spantree portvlanpri 4/1 0 set spantree portvlancost 4/1 cost 13 ! #module 5 : 2-port MM MIC FDDI set module name 5 set module enable 5 set fddi userdata 5 WorkGroup Stack set fddi tnotify 5 30 set fddi treq 5 165000 set fddi tlmin 5/1 40 set fddi tlmin 5/2 40 set vlan 1 5/1 set port enable 5/1-2 set port level 5/1 normal set port trap 5/1-2 disable set port name 5/1-2 set cdp enable 5/1 set cdp interval 5/1 60 set trunk 5/1 off dot10 1-1005 set spantree portcost 5/1 19 set spantree portpri 5/1 32 set spantree portvlanpri 5/1 0 set spantree portvlancost 5/1 cost 18 ! #module 6 : 3-port 1000BaseX Ethernet set module name 6 set module enable 6 set vlan 1 6/1-3 set port enable 6/1-3 set port level 6/1-3 normal set port duplex 6/1-3 full set port trap 6/1-3 disable set port name 6/1-3 set port security 6/1-3 disable set port broadcast 6/1-3 100% set port membership 6/1-3 static set port negotiation 6/1-3 enable set port flowcontrol send 6/1-3 desired set port flowcontrol receive 6/1-3 off set cdp enable 6/1-3 set cdp interval 6/1-3 60 set trunk 6/1 auto isl 1-1005 set trunk 6/2 auto isl 1-1005 set trunk 6/3 auto isl 1-1005 set spantree portfast 6/1-3 disable set spantree portcost 6/1-3 4 set spantree portpri 6/1-3 32 set spantree portvlanpri 6/1 0 set spantree portvlanpri 6/2 0 set spantree portvlanpri 6/3 0 set spantree portvlancost 6/1 cost 3 set spantree portvlancost 6/2 cost 3 set spantree portvlancost 6/3 cost 3 ! #module 7 : 2-port UTP OC-3 Dual-Phy ATM set module name 7 set port level 7/1 normal set port name 7/1-2 set cdp enable 7/1 set cdp interval 7/1 60 set trunk 7/1 on lane 1-1005 set spantree portcost 7/1 14 set spantree portpri 7/1 32 set spantree portvlanpri 7/1 0 set spantree portvlancost 7/1 cost 13 ! #module 8 : 2-port DS3 Dual PHY ATM set module name 8 set port level 8/1 normal set port name 8/1-2 set cdp enable 8/1 set cdp interval 8/1 60 set trunk 8/1 on lane 1-1005 set spantree portcost 8/1 39 set spantree portpri 8/1 32 set spantree portvlanpri 8/1 0 set spantree portvlancost 8/1 cost 38 ! #module 9 empty ! #module 10 empty ! #module 11 empty ! #module 12 empty ! #module 13 empty ! #switch port analyzer set span 2/1 3/1 both ! #cam set cam agingtime 1,521-524,1003,1005 300 end
This example shows how to display the current ATM configuration information:
ATM#write terminal
Building configuration...
Current configuration:
!
version 11.2
!
hostname ATM
!
!
!
interface ATM0
atm preferred phy A
atm pvc 1 0 5 qsaal
atm pvc 2 0 16 ilmi
lane client ethernet 100
!
!
line con 0
line vty 0 4
no login
!
end
ATM#
Posted: Mon Jul 19 13:07:08 PDT 1999
Copyright 1989-1999©Cisco Systems Inc.