|
|
This chapter describes the general commands used in the Catalyst 5000 series switch CLI. For a summary of the available switch CLI commands, refer to the "Switch Command Quick Reference" chapter. For more information about using the switch CLI, refer to the "Switch Command-Line Interface" chapter.
Use the configure command to download a configuration file from the network and execute each command in that file.
configure {host file | network}| host | IP address or IP alias of the host. |
| file | Name of the file. |
| network | Keyword that specifies interactive prompting for the host and the file. |
This command has no default setting.
Switch command.
Privileged.
Refer to the "Creating a Configuration File" appendix in the Catalyst 5000 Series Software Configuration Guide on how to construct a configuration file to download using the configure command.
Following is a sample file called system5.cfg in the /tftpboot directory:
begin show time set ip alias conc7 198.133.219.207 set ip alias montreux 198.133.119.42 set ip alias cres 192.122.174.42 set prompt system5> set password # empty string old password pingpong pingpong end #
Each line contains a command, except lines that begin with ! or #.
This example shows how to download the system5.cfg configuration file from the 192.122.174.42 host:
Console> (enable) configure 192.122.174.42 system5.cfg Configure using system5.cfg from 192.122.174.42 (y/n) [n]? y / Done. Finished Network Download. (446 bytes) >> show time Wed Feb 22 1995, 17:42:50 >> set ip alias conc7 198.133.219.207 IP alias added. >> set ip alias montreux 198.133.219.40 IP alias added. >> set ip alias cres 192.122.174.42 IP alias added. >> set prompt system5> >> set password Enter old password: Enter new password: pingpong Retype new password: pingpong Password changed. system5> (enable)
Use the disable command to return to normal mode from privileged mode.
disableThis command has no arguments or keywords.
This command has no default setting.
Switch command.
Privileged.
This example shows how to return to normal mode:
Console> (enable) disable Console>
Use the disconnect command to close an active console port or Telnet session.
disconnect {ip_addr | console}| ip_addr | IP address or IP alias. |
| console | Keyword that denotes an active console port. |
This command has no default setting.
Switch command.
Privileged.
If multiple sessions from the same IP address exist, the disconnect command checks if the current process is also from the same IP address. If it is not, all Telnet sessions from the specified IP address are disconnected. If it is, all sessions, other than the current session, are disconnected. The system prompts whether to disconnect the current Telnet session. You can answer n and remain connected or answer y and be disconnected.
This example shows how to close a Telnet session to host 198.134.214.4:
Console> (enable) disconnect 198.134.214.4 Telnet session from 198.134.214.4 disconnected. (1) Console> (enable)
This example shows how to close the current console session:
Console> (enable) disconnect console Console session disconnected. Console> (enable)
Use the download command to copy a software image from a specified host to the Flash memory of a designated module.
download host file [mod_num]| host | Name or IP address of host. |
| file | Name of file to be downloaded. |
| mod_num | (Optional) Number of the module to receive downloaded image. |
| serial | Keyword that specifies download through a serial port. |
If a module number is not specified, the image is downloaded to all modules for which the image is valid.
Switch command.
Privileged.
The Catalyst 5000 series switches support two ways to download new code to the processors: TFTP network download through any network port, and Kermit serial download through the EIA/TIA-232 console port. Only the first applies to the ATM module. The ATM module has processors that will require field upgrades.
The download command downloads code to the module Flash memory. Catalyst 5000 series software rejects an image if it is not a valid image for the module.
When downloading to the ATM module, the supervisor module acts as a TFTP gateway, forwarding TFTP packets to the ATM module through an in-band IPC method.
To download a software image for the RSM, use the session command.
The download serial command uses the Kermit protocol through the serial EIA/TIA-232 console port. The download serial command is not allowed from a Telnet session.
This command is not supported by the three-port Gigabit Ethernet switching module (WS-X5403).
If the module number is specified, the download goes to the specified module, but the download will fail if the module is of a different type than is indicated by the download header. If the module number is not specified, the download goes to all modules of that type.
 Caution
| After starting the serial download using Kermit, do not attempt to abort the serial download by using Ctrl-C. Pressing Ctrl-C interrupts the download process and could leave the switch in a problematic state. If this occurs, reboot the switch. |
This example shows how to download the c5000_spv11.bin file from the mercury host to the supervisor engine module (by default):
Console> (enable) download mercury c5000_spv11.bin Download image c5000_spv11.bin from mercury to module 1FLASH (y/n) [n]? y \ Finished network single module download. (2418396 bytes) FLASH on Catalyst: Type Address Location Intel 28F008 20000000 NMP (P3) 4MB SIM Erasing flash sector...done. Programming flash sector...done. Erasing flash sector...done. Programming flash sector...done. The system needs to be reset to run the new image. Console> (enable)
This example shows how to download the fddi_1113.cpi file from the mercury host to module 4:
Console> (enable) download mercury fddi_1113.cpi 4 This command will reset Module 4. Download image fddi_1113.cbi from mercury to Module 4 FLASH (y/n) [n]? y | Finished network download. (1064876 bytes) ...............................................................................n Console> (enable)
This example shows how to download the acpflash_1111.bbi file from the mercury host to module 3:
Console> (enable) download mercury acpflash_1111.bbi 3 This command will reset Module 3. Download image acpflash_1111.bbi from mercury to Module 3 FLASH (y/n) [n]? y / Done. Finished network download. (1964012 bytes) Console> (enable)
This sample session shows how to connect to a remote terminal from a Sun workstation and how to use the download serial command to copy a software image to the supervisor card:
[At local Sun workstation]
host% kermit
C-Kermit 5A(172) ALPHA, 30 Jun 95, SUNOS 4.0 (BSD)
Type ? or 'help' for help
C-Kermit> set line /dev/ttyb
C-Kermit> c
Connecting to /dev/ttyb, speed 9600.
The escape character is ^ (ASCII 28).
Type the escape character followed by C to get back,
or followed by ? to see other options.
Console> enable
Enter Password:
Console> (enable) set system baud 19200
^\C
[Back at local Sun workstation]
C-Kermit> set speed 19200
/dev/ttyb, 19200 bps
C-Kermit> c
Connecting to /dev/ttyb, speed 19200.
The escape character is ^ (ASCII 28).
Type the escape character followed by C to get back,
or followed by ? to see other options.
Console> (enable) download serial
Download Supervisor image via console port (y/n) [n]? y
Concentrator Boot ROM (Ver 1.00)
Waiting for DOWNLOAD!!
Return to your local Machine by typing its escape sequence
Issue Kermit send command from there[ Send 'Filename']
^\C
[Back at Local System]
C-Kermit> send c5000_xx.bin
SF
c5000_xx.bin => C5000_XX.BIN, Size: 1233266
X to cancel file, CR to resend current packet
Z to cancel group, A for status report
E to send Error packet, Ctrl-C to quit immediately: ..........................
...............................................................................
...... [OK]
ZB
C-Kermit> quit
host%
Use the download vmps command to download VMPS database information from a TFTP server.
download vmpsThis command has no arguments or keywords.
There is no default setting for this command.
Switch command.
Privileged.
Before you can successfully execute the download vmps command, you must use the set storage command to configure the IP address of the TFTP server and the name of the VMPS configuration file on that server. If the IP address of the TFTP server is not configured, the download vmps command reports an error. If the configuration filename is not configured, the download vmps command uses the default filename vmps-config-database.1.
After a successful download, the new VMPS information replaces any existing information. If there are not enough resources to build the new configuration database, the VMPS is made inactive.
This example shows the download vmps command and typical system responses:
Console> (enable) download vmps Re-initialization of Vlan Membership Policy Server with the downloaded configuration file is in progress. 6/4/1997,17:37:29:VMPS-2:PARSER: 82 lines parsed, Errors 0
Use the enable command to activate privileged mode. In privileged mode, additional commands are available, and certain commands display additional information.
enableThis command has no arguments or keywords.
This command has no default setting.
Switch command.
Normal.
The designation "(enable)" in the prompt indicates that the system is in privileged mode and that commands can be entered.
This example shows how to enter privileged mode:
Console> enable Enter password: Console> (enable)
Use the history command to show the contents of the command history buffer.
historyThis command has no arguments or keywords.
This command has no default setting.
Switch command.
Normal.
The history buffer size is fixed at 20 commands. Refer to the "Switch Command-Line Interface" chapter for detailed information about the command history feature.
In this example, the history command lists the contents of the command history buffer:
Console> history
1 show time
2 history
In this example, the !1 command repeats the first command in the history buffer (show time) and displays the output:
Console> !1 show time Thu Mar 19 1998, 22:24:19 Console>
Use the ping command to send ICMP echo request packets to another node on the network.
ping [-s] host [packet_size] [packet_count]| -s | (Optional) Keyword used to cause ping to send one datagram per second, printing one line of output for every response received. The ping command returns output only when a response is received. |
| host | IP address or IP alias of the host. |
| packet_size | (Optional) Number of bytes in a packet, from 56 to 1472 bytes. The default is 56 bytes. The actual packet size will be eight bytes larger than the size specified because the switch adds header information. |
| packet_count | (Optional) Number of packets to send. |
This command has no default setting.
Switch command.
Normal.
Press Ctrl-C to stop pinging.
Following are sample results of the ping command:
This example shows how to ping a host with IP alias elvis a single time:
Console> ping elvis elvis is alive Console>
This example shows how to ping a host with IP alias elvis once per second until you press Ctrl-C to stop pinging:
Console> ping -s elvis ping elvis: 56 data bytes 64 bytes from elvis: icmp_seq=0. time=11 ms 64 bytes from elvis: icmp_seq=1. time=8 ms 64 bytes from elvis: icmp_seq=2. time=8 ms 64 bytes from elvis: icmp_seq=3. time=7 ms 64 bytes from elvis: icmp_seq=4. time=11 ms 64 bytes from elvis: icmp_seq=5. time=7 ms 64 bytes from elvis: icmp_seq=6. time=7 ms ^C ----elvis PING Statistics---- 7 packets transmitted, 7 packets received, 0% packet loss round-trip (ms) min/avg/max = 7/8/11 Console>
set interface
set ip route
show interface
show ip route
Use the quit command to exit a CLI session.
quitThis command has no arguments or keywords.
This command has no default setting.
Switch command.
Normal.
The exit and logout commands perform the same function as the quit command.
This example shows how to quit a CLI session:
Console> quit Connection closed by foreign host. host%
Use the reconfirm vmps command to reconfirm the current dynamic port VLAN membership with VMPS.
reconfirm vmpsThis command has no arguments or keywords.
This command has no default setting.
Switch command.
Privileged.
VMPS database changes are not automatically conveyed to dynamic port entities; therefore, after making a VMPS database change, you can use this command to apply the change to the dynamic port entity on a device.
This example shows how to reconfirm the current dynamic port VLAN membership with VMPS:
Console (enable)> reconfirm vmps reconfirm process started Use 'show dvlan statistics' to see reconfirm status Console (enable)>
clear vmps server
show dvlan statistics
Use the reset command to restart the system or an individual module.
reset {mod_num | system}| mod_num | Number of the module to be restarted. |
| system | Keyword used to reset the system to its default values. |
This command has no default setting.
Switch command.
Privileged.
If no module number or module number of the active supervisor engine module is specified, the command resets the entire system.
You can use the reset mod_num command to switch to the standby supervisor engine, where mod_num is the slot number of the active supervisor.
Where mod_num is an RSM, both the RSM hardware and software are completely reset.
This example shows how to reset the supervisor engine module on a Catalyst 5500 switch with redundant supervisors:
Console> (enable) reset 1 This command will force a switch-over to the standby supervisor module and disconnect your telnet session. Do you want to continue (y/n) [n]? y Connection closed by foreign host. host%
This example shows how to reset module 4:
Console> (enable) reset 4 This command will reset module 4 and may disconnect your telnet session. Do you want to continue (y/n) [n]? y Resetting module 4... Console> (enable)
Use the session command to open a session with the ATM module or the RSM, allowing you to use the ATM or RSM CLI.
session mod_num| mod_num | Number of the ATM or RSM module. |
This command has no default setting.
Switch command.
Privileged.
After you enter this command, the system responds with the Enter Password: prompt, if one is configured on the module.
To end the session with the ATM module or RSM, enter the quit command.
Use the session command to toggle between router and switch sessions.
This command is not supported by the three-port Gigabit Ethernet switching module (WS-X5403).
This example shows how to open a session with an ATM module (module 4):
Console> session 4 Trying ATM-4... Connected to ATM-4. Escape character is '^]'. ATM>
Use the slip command to attach or detach SLIP for the console port.
slip {attach | detach}| attach | Keyword used to activate SLIP for the console port. |
| detach | Keyword used to deactivate SLIP for the console port. |
By default, SLIP is not active (detached).
Switch command.
Privileged.
You can use the slip command from a console port session or a Telnet session.
This example shows how to enable SLIP for a console port during a console port session:
Console> (enable) slip attach Console port now running SLIP. <console port running SLIP>
This example shows how to disable SLIP for a console port during a Telnet session:
Console> (enable) slip detach SLIP detached on Console port. <console port back to RS-232 Console> Console> (enable)
Use the switch command to switch the clock from the supervisor clock to the internal clock, or to switch from the active supervisor to the standby supervisor.
switch {clock | supervisor}| clock | Keyword used to switch the clock from the supervisor clock to the internal clock. |
| supervisor | Keyword used to switch from the active supervisor to the standby supervisor (Catalyst 5500 and Catalyst 5505 switches only). |
This command has no default setting.
Switch command.
Privileged.
The switch keyword can be used only on Catalyst 5500 and Catalyst 5505 switches.
This example shows how to switch the clock:
Console> (enable) switch clock This command will reset system and force a clock switch-over. Do you want to continue (y/n) [n]? Console> (enable)
This example shows how to switch to the standby supervisor:
Console> (enable) switch supervisor This command will force a switch-over to the standby Supervisor module. Do you want to continue (y/n) [n]? Console> (enable)
Use the telnet command to start a Telnet connection to a remote host.
telnet host [port_num]| host | Remote host to which you want to connect. |
| port_num | (Optional) Specific port connection on the remote host. |
This command has no default setting.
Switch command.
Privileged.
This example shows how to open and close a Telnet session with the host elvis:
Console> (enable) telnet elvis Trying 192.122.174.11... Connected to elvis. Escape character is '^]'. UNIX(r) System V Release 4.0 (elvis) login: fred Password: Last login: Thu Feb 15 09:25:01 from forster.cisc.rum Sun Microsystems Inc. SunOS 5.4 Generic July 1994 You have new mail. % logout Console> (enable)
Use the test snmp trap command to send an SNMP trap message to the trap receivers.
test snmp trap trap_num [specific_num]| trap_num | Number of the trap. |
| specific_num | (Optional) Number of a predefined trap. |
This command has no default setting.
Switch command.
Privileged.
This example shows how to run trap 0:
Console> (enable) test snmp trap 0 SNMP trap message sent. (4) Console> (enable)
Use the traceroute command to display a hop-by-hop path through an IP network from the Catalyst 5000 series switch to a specific destination host.
traceroute [-n] [-w wait_time] [-i initial_ttl] [-m max_ttl] [-p dest_port] [-q nqueries] [-t tos] host [data_size]| -n | (Optional) Option that prevents traceroute from performing a DNS lookup for each hop on the path. Only numerical IP addresses are printed. |
| -w wait_time | (Optional) Option used to specify the amount of time (in seconds) that traceroute will wait for an ICMP response message. The allowed range for wait_time is 1 to 300 seconds; the default is 5 seconds. |
| -i initial_ttl | (Optional) Option that causes traceroute to send ICMP datagrams with a TTL value equal to initial_ttl instead of the default TTL of 1. This causes traceroute to skip processing for hosts that are less than initial_ttl hops away. |
| -m max_ttl | (Optional) Option used to specify the maximum TTL value for outgoing ICMP datagrams. The allowed range for max_ttl is 1 to 255; the default value is 30. |
| -p dest_port | (Optional) Option used to specify the base UDP destination port number used in traceroute datagrams. This value is incremented each time a datagram is sent. The allowed range for dest_port is 1 to 65535; the default base port is 33434. Use this option in the unlikely event that the destination host is listening to a port in the default traceroute port range. |
| -q nqueries | (Optional) Option used to specify the number of datagrams to send for each TTL value. The allowed range for nqueries is 1 to 1000; the default is 3. |
| -t tos | (Optional) Option used to specify the TOS to be set in the IP header of the outgoing datagrams. The allowed range for tos is 0 to 255; the default is 0. Use this option to see if different types of service cause routes to change. |
| host | IP alias or IP address in dot notation (a.b.c.d) of the destination host. |
| data_size | (Optional) Number of bytes, in addition to the default of 40 bytes, of the outgoing datagrams. The allowed range is 0 to 1420; the default is 0. |
Entering the traceroute host command without options sends three 40-byte ICMP datagrams with an initial TTL of 1, a maximum TTL of 30, a timeout period of 5 seconds, and a TOS specification of 0 to destination UDP port number 33434. For each host in the processed path, the initial TTL for each host and the destination UDP port number for each packet sent are incremented by one.
Switch command.
Privileged.
To interrupt traceroute after the command has been issued, press Ctrl-C.
The traceroute command uses the TTL field in the IP header to cause routers and servers to generate specific return messages. Traceroute starts by sending a UDP datagram to the destination host with the TTL field set to 1. If a router finds a TTL value of 1 or 0, it drops the datagram and sends back an ICMP "time exceeded" message to the sender. The traceroute facility determines the address of the first hop by examining the source address field of the ICMP time-exceeded message.
To identify the next hop, traceroute again sends a UDP packet but this time with a TTL value of 2. The first router decrements the TTL field by 1 and sends the datagram to the next router. The second router sees a TTL value of 1, discards the datagram, and returns the time-exceeded message to the source. This process continues until the TTL is incremented to a value large enough for the datagram to reach the destination host (or until the maximum TTL is reached).
To determine when a datagram has reached its destination, traceroute sets the UDP destination port in the datagram to a very large value that the destination host is unlikely to be using. When a host receives a datagram with an unrecognized port number, it sends an ICMP "port unreachable" error to the source. This message indicates to the traceroute facility that it has reached the destination.
Catalyst 5000 series switches can participate as the source or destination of the traceroute command. However, because they are Layer 2 devices, Catalyst 5000 series switches do not examine the TTL field in the IP header and therefore do not decrement the TTL field or send ICMP time-exceeded messages. Thus, a Catalyst 5000 series switch does not appear as a hop in the traceroute command output.
This example shows how to use the traceroute command to determine the path from the source to the destination host server10:
Console> (enable) traceroute server10 traceroute to server10.company.com (172.16.22.7), 30 hops max, 40 byte packets 1 engineering-1.company.com (172.31.192.206) 2 ms 1 ms 1 ms 2 engineering-2.company.com (172.31.196.204) 2 ms 3 ms 2 ms 3 gateway_a.company.com (172.16.1.201) 6 ms 3 ms 3 ms 4 server10.company.com (172.16.22.7) 3 ms * 2 ms Console> (enable)
Table 5-1 describes the fields in the traceroute command output.
| Field | Description |
|---|---|
| 30 hops max, 40 byte packets | Maximum TTL value and the size of the ICMP datagrams being sent. |
| 2 ms 1 ms 1 ms | Total time (in milliseconds) for each ICMP datagram to reach the router or host plus the time it took for the ICMP time-exceeded message to return to the host.
An exclamation point following any of these values (for example, 20 ms !) indicates that the port-unreachable message returned by the destination had a TTL of 0 or 1. This typically occurs when the destination uses the TTL value from the arriving datagram as the TTL in its ICMP reply. The reply does not arrive at the source until the destination receives a traceroute datagram with a TTL equal to the number of hops between the source and destination. |
| 3 ms * 2 ms | "*" indicates that the timeout period (default of 5 seconds) expired before an ICMP time-exceeded message was received for the datagram. |
If traceroute receives an ICMP error message other than a time-exceeded or port-unreachable message, it prints one of the error codes shown in Table 5-2 instead of the round-trip time or an asterisk (*).
| ICMP Error Code | Meaning |
|---|---|
| !N | No route to host. The network is unreachable. |
| !H | No route to host. The host is unreachable. |
| !P | Connection refused. The protocol is unreachable. |
| !F | Fragmentation needed but do not fragment (DF) bit was set. |
| !S | Source route failed. |
| !A | Communication administratively prohibited. |
| ? | Unknown error occurred. |
Use the upload command to upload a software image to a network host.
upload host file [mod_num]| host | IP address or IP alias of the host. |
| file | Name of the image file. |
| mod_num | (Optional) Number of the module from which to upload the image file. If no number is specified, the default is module 1. |
This command has no default setting.
Switch command.
Privileged.
To upload a software image for the RSM, use the session command.
This command is not supported by the three-port Gigabit Ethernet switching module (WS-X5403).
This example shows how to upload the supervisor image to the c5009_11.bin file on the mercury host:
Console> (enable) upload mercury c5009_11.bin 3 Upload Module 1 image to c5009_11.bin on mercury (y/n) [n]? y / Done. Finished Network Upload. (153908 bytes) Console> (enable)
Use the wait command to cause the CLI to pause for a specified number of seconds before executing the next command. This command might be included in a configuration file.
wait seconds| seconds | Number of seconds for the CLI to wait. |
This command has no default setting.
Switch command.
Normal.
This example shows how to pause the CLI for five seconds:
Console> wait 5 Console>
Use the write command to upload the current configuration to a host or display it on the terminal.
write {host file | network | terminal}| host | IP address or IP alias of the host. |
| file | Name of the configuration file. |
| network | Keyword that specifies interactive prompting for the IP address or IP alias of the host and the filename to upload. |
| terminal | Keyword used to display the configuration file on the terminal. |
This command has no default setting.
Switch command.
Privileged.
The write terminal command is exactly the same as the show config command. The write host file command is a shorthand version of the write network command.
The write terminal command is equivalent to the ATM command write terminal.
You cannot use the write network command to upload software to the ATM module.
With the write network command, the file must already exist on the host (use the UNIX touch filename command to create it).
This sample session assumes that module 1 is a 2-port supervisor module, module 2 is a 12-port 10/100BaseT switched Ethernet module, modules 3 and 5 are empty, and module 4 is an FDDI module. Details of the ATM configuration must be accessed through the special module mode.
This example shows how to upload the system5.cfg file to the mercury host using the write network command:
Console> (enable) write network IP address or name of host? mercury Name of configuration file to write? system5.cfg Upload configuration to system5.cfg on mercury (y/n) [y]? y / Done. Finished Network Upload. (9003 bytes) Console> (enable)
This example shows how to upload the system5.cfg file to the mercury host using the write host file command as a shorthand method:
Console> (enable) write mercury system5.cfg Upload configuration to system5.cfg on mercury (y/n) [y]? y / Done. Finished Network Upload. (9003 bytes) Console> (enable)
This example shows how to use the write terminal command to display the configuration file on the terminal:
Console> (enable) write terminal begin set password $1$FMFQ$HfZR5DUszVHIRhrz4h6V70 set enablepass $1$FMFQ$HfZR5DUszVHIRhrz4h6V70 set prompt Console> ! #system set system baud 9600 set system modem disable set system name set system location set system contact ! #snmp set snmp community read-only public set snmp community read-write private set snmp community read-write-all secret set snmp trap disable ! #vlan/trunk set vlan 1 1/1-2,4/1 set vlan 2 2/1-5 ! #trunks ! #cam set cam agingtime 1 300 set cam agingtime 2 300 ! #ip set interface sc0 0.0.0.0 0.0.0.0 0.0.0.0 set interface sl0 0.0.0.0 0.0.0.0 set ip redirect enable set ip unreachable disable set ip fragmentation enable set ip alias default 0.0.0.0 set arp agingtime 1200 ! #bridge set bridge ipx snaptoether 8023raw set bridge ipx 8022toether 8023 set bridge ipx 8023rawtofddi snap ! #Command alias ! #cdp set cdp enable 1/1-2,2/1-5,4/1 set cdp interval 1/1 60 set cdp interval 1/2 60 set cdp interval 2/1 60 set cdp interval 2/2 60 set cdp interval 2/3 60 set cdp interval 2/4 60 set cdp interval 2/5 60 set cdp interval 4/1 60 ! #spantree #vlan 1 set spantree enable 1 set spantree fwddelay 15 1 set spantree hello 2 1 set spantree maxage 20 1 set spantree priority 32768 1 set spantree portpri 1/1 32 set spantree portcost 1/1 10 set spantree portpri 1/2 32 set spantree portcost 1/2 10 set spantree portpri 4/1 32 set spantree portcost 4/1 10 #vlan 2 set spantree enable 2 set spantree fwddelay 15 2 set spantree hello 2 2 set spantree maxage 20 2 set spantree priority 32768 2 set spantree portpri 2/1 32 set spantree portcost 2/1 100 set spantree portpri 2/2 32 set spantree portcost 2/2 100 set spantree portpri 2/3 32 set spantree portcost 2/3 100 set spantree portpri 2/4 32 set spantree portcost 2/4 100 set spantree portpri 2/5 32 set spantree portcost 2/5 100 ! #trunk ! #module 1 set module name 1 set port enable 1/1 set port name 1/1 set port duplex 1/1 half set port level 1/1 normal set port enable 1/2 set port name 1/2 set port duplex 1/2 half set port level 1/2 normal ! #module 2 set module name 2 set module enable 2 ! set port enable 2/1 set port name 2/1 set port duplex 2/1 half set port level 2/1 normal set port enable 2/2 set port name 2/2 set port duplex 2/2 half set port level 2/2 normal set port enable 2/3 set port name 2/3 set port duplex 2/3 half set port level 2/3 normal set port enable 2/4 set port name 2/4 set port duplex 2/4 half set port level 2/4 normal set port enable 2/5 set port name 2/5 set port duplex 2/5 half set port level 2/5 normal ! #module 3 empty ! #module 4 set module name 4 set module enable 4 ! set fddi userdata 4 WorkGroup Stack set fddi tnotify 4 30 set fddi treq 4 5000 set port enable 4/1 set port name 4/1 set port level 4/1 normal set fddi tlmin 4/1 40 set port enable 4/2 set port name 4/2 set port level 4/2 normal set fddi tlmin 4/2 40 ! #module 5 empty end Console> (enable)
|
|