cc/td/doc/product/lan/cat5000/rel_4_1
hometocprevnextglossaryfeedbacksearchhelp
PDF

Table of Contents

ATM Command Quick Reference

ATM Command Quick Reference

This chapter provides a quick command reference for the Catalyst 5000 series ATM module CLI.

Table 9-1 identifies each command in the ATM module command set, gives the command syntax, provides a short description, and specifies the command type and mode.


Table  9-1: ATM Module Command Set
Command Syntax Description Type1 Mode2
atm bind pvc vlan atm bind pvc vlan vcd vlan_num Binds a PVC to a specified VLAN. ATM IC
atm clock internal3 atm clock internal
no atm clock internal 		Specifies the transmit clock source. ATM IC
atm ds3-scramble atm ds-3 scramble
no atm ds-3 scramble 		Enables or disables scrambling on the current port. ATM IC
atm framing atm framing [m23adm | cbitplcp | m23plcp]
no atm framing 		Changes the default DS3 line framing. ATM IC
atm ilmi-enable atm ilmi-enable
no atm ilmi-enable 		Enables or disables the ILMI. ATM IC
atm ilmi-keepalive atm ilmi-keepalive seconds
no atm ilmi-keepalive seconds 		Enables ILMI keepalives. ATM IC
atm lbo atm lbo {short | long} Sets the line buildout corresponding to the cable length. ATM IC
atm preferred phy atm preferred phy {A | B} Changes the preferred PHY. LANE IC
atm pvc atm pvc vcd vpi vci [aal5snap | ilmi | qsaal]
atm pvc vcd vpi vci [aal5snap | ilmi | qsaal] [peak_rate average_rate [burst_size]] [oam seconds]4
no atm pvc vcd vpi vci 		Creates a PVC on the ATM interface. ATM IC
atm sonet5 atm sonet {stm-4 | sts-12c}
no atm sonet 		Sets the mode of operation and control type for cell-rate decoupling. ATM IC
atm traffic-shape rate atm traffic-shape rate 1-155
no atm traffic-shape rate 		Configures output throttling on the ATM module. ATM IC
atm uni-version atm uni-version version_num
no atm uni-version 		Specifies the UNI version to be used. ATM GC
atm vc-per-vp atm vc-per-vp num
no atm vc-per-vp 		Sets the maximum number of VCIs to support per VCI. ATM IC
atmsig close atmsig close atm0 vcd Disconnects an SVC. ATM IC
client-atm-address name client-atm-address atm-address-template name elan-name
no client-atm-address atm-address-template 		Adds a LANE address entry to the configuration server's database. LANE Dbase
default-name default-name elan-name
no default name 		Provides a default ELAN name in the configuration server's database. ATM Dbase
disable disable [level] Exits privileged EXEC mode and returns to user EXEC mode. ATM EXEC
editing editing
no editing 		Enables enhanced editing mode. ATM Line
enable enable Enters privileged EXEC mode. ATM EXEC
end end Exits configuration mode. ATM GC
exit exit Exits any command mode or closes an active terminal session and terminates the EXEC. ATM ATM
help help Displays the help commands. ATM ATM
history history [size number-of-lines]
no history 		Enables the command history function. ATM Line
interface interface atm_num[.sub_interface_num mul] | loopback_num Enters the configure interface or subinterface mode. ATM IC
lane auto-config-atm-address lane [config] auto-config-atm-address
no lane [config] auto-config-atm-address 		Specifies the ATM address is computed automatically. ATM IC
lane client lane client ethernet vlan_num [elan-name]
no lane client [ethernet vlan_num [elan-name]] 		Activates a LANE client. LANE IC
lane client-atm-address lane client-atm-address atm-address-template
no client-atm-address [atm-address-template] 		Specifies an ATM address for the LANE client (overriding automatic assignment). LANE IC
lane config-atm-address lane config-atm-address atm-address-template
no lane config-atm-address [atm-address-template] 		Specifies the ATM address of a given configuration server. LANE IC
lane config database lane config database database-name
no lane config database 		Associates a named configuration database with the configuration server on the selected ATM interface. LANE GC
lane database lane database database-name
no lane database database-name 		Creates a named configuration database that can be associated with a configuration server. LANE GC
lane le-arp lane le-arp mac-addr atm-addr
no lane le-arp mac-addr atm-addr 		Adds a static entry to the LE ARP table. LANE IC
lane register lane register vcd mac-addr atm-addr
no lane register vcd [mac-addr atm-addr] 		Registers a LANE client. LANE IC
lane server-bus lane server-bus ethernet elan_name
no lane server-bus ethernet elan_name 		Configures the LES and BUS for the specified ELAN on the subinterface. LANE IC
name server-atm-address name elan_name server-atm-address atm-addr
no name elan_name server-atm-address 		Assigns a unique ELAN name to a LES. LANE Dbase
reload reload Reloads the operating system. Config EXEC
show atm interface atm show atm interface atm0 Displays information about the ATM interface. ATM EXEC
show atm traffic show atm traffic Displays global ATM traffic information. ATM EXEC
show atm vc show atm vc [vcd] Displays the active ATM virtual circuits. ATM EXEC
show atm vlan show atm vlan [vlan_num] Displays the active VLAN-to-PVC bindings. ATM IC
show history show history Lists the command history for the current EXEC session. ATM EXEC
show lane show lane [interface atm0[.subinterface] | name elan-name] [brief] Displays global and per-VCC LANE information. LANE EXEC
show lane bus show lane bus [interface atm0[.subinterface] | name elan-name] [brief] Displays LANE information for the configured BUS. LANE EXEC
show lane client show lane client [interface atm0[.subinterface] | name elan-name] [brief] Displays global and per-VCC LANE information. LANE EXEC
show lane config show lane config [interface atm0] [brief] Displays LANE information for the LECS. LANE EXEC
show lane default-atm-addresses show lane default-atm-addresses Displays default ATM addresses for dual PHYs. LANE EXEC
show lane le-arp show lane le-arp [interface atm0[.subinterface] | name elan-name] Displays the LE ARP table. LANE EXEC
show lane server show lane server [interface atm0[.subinterface] | name elan-name] [brief] Displays LANE information about the configured LES. LANE EXEC
show sscop show sscop Displays SSCOP details for all ATM interfaces. ATM EXEC
show version show version Displays version information for the ATM module. Config EXEC
sscop cc-timer sscop cc-timer seconds
no sscop cc-timer 		Changes the SSCOP connection control timer period. ATM IC
sscop keepalive-timer sscop keepalive-timer seconds
no sscop keepalive-timer 		Changes the SSCOP keepalive timer period. ATM IC
sscop max-cc sscop max-cc retries
no sscop max-cc 		Changes the SSCOP connection control retry count. ATM IC
sscop poll-timer sscop poll-timer seconds
no sscop poll-timer 		Changes the SSCOP poll timer period. ATM IC
sscop rcv-window sscop rcv-window packets
no sscop rcv-window 		Changes the size of the SSCOP receiver window. ATM IC
sscop send-window sscop send-window packets
no sscop send-window 		Changes the size of the SSCOP transmitter window. ATM IC
terminal terminal length [screen-length]
terminal no length 		Sets the number of lines displayed on the terminal. ATM EXEC
write erase write erase Erases the configuration information in NVRAM. Config EXEC
write memory write memory Copies the configuration information in running memory to NVRAM. Config EXEC
write terminal write terminal Displays the configuration information currently in running memory. Config EXEC

1 Type - indicates whether the command is an ATM, LANE, or configuration command.
2 Mode - indicates whether the command is available in every command mode (All) or whether it is an EXEC, global configuration (GC), interface configuration (IC), line configuration (Line), or database configuration (Dbase) command.
3 This command is not supported by the ATM dual PHY OC-12 module, ATM software release 4.3(0).
4 This version of the atm pvc command is available only in ATM software release 50.1(1) and later, ATM software release 51.1(1) and later.
5 This command applies only to the ATM dual PHY OC-12 module.


hometocprevnextglossaryfeedbacksearchhelp
Copyright 1989-1998 © Cisco Systems Inc.