|
|
The Catalyst 5000 series switch system specifications are described in Table A-1.
| Description | Specifications |
|---|---|
| Backplane | 1.2-Gbps1, 5 module connections |
| Dimensions (H x W x D) | 10.4 x 17.25 x 18.4" (26.4 x 43.1 x 46.0 cm) Chassis depth including cable guide is 21.64" (55.0 cm) |
| Weight | Chassis only: 43 lb (19.5 kg) Chassis fully configured with 1 supervisor engine module, 4 switching modules, and 2 power supplies: 84 lb (39 kg) |
| DC voltages supplied and steady-state maximum current ratings | +5V @ 70A +12V @ 2A +24V @ 0.2A |
| Power supply | 376W maximum (AC-input power supplies) |
| Power dissipation | 350W maximum configuration, 110W typical with maximum configuration |
| Heat dissipation | 563W (1919 Btu2/hr) |
| Input voltage | 100-240 VAC wide input with power factor corrector |
| Frequency | 47-63 Hz autoranging |
| AC current rating | 8A maximum at 100-127 VAC, 4A maximum at 200-240 VAC with the chassis fully configured. A maximum of 0.8 kva. |
| Airflow | 95 cfm3 through the system fan assembly |
| Operating temperature | 32-104°F (0-40°C) |
| Nonoperating temperature | -40-167°F (-40-75°C) |
| Humidity | 10-90%, noncondensing |
| Microprocessor | 25-MHz 68EC040 for the NMP4 |
| Memory | 4 MB of Flash memory 8MB of packet-buffer DRAM5 256 KB of NVRAM6 |
| Interface ports | 4 RJ-21 IEEE 802.3 Group Switching Ethernet 10BaseT (WS-X5020) 2 RJ-21 IEEE 802.3 Ethernet 10BaseT (WS-X5010) 12 ST multimode 802.3 Ethernet 10BaseFL (WS-X5011) 12 RJ-45 IEEE 802.3u Fast Ethernet 10/100 BaseTX (WS-X5213) and 100BaseTX (WS-X5113) 2 RJ-45 IEEE 802.3u Fast Ethernet 100BaseTX on supervisor engine module 2 40-pin MII7 IEEE 802.3u Fast Ethernet 100BaseTX MII and a DB-25 console port for an administration workstation on supervisor engine module (WS-C5009) 12 RJ-45 IEEE 802.3u Ethernet 12 SC multimode 802.3u Fast Ethernet 100BaseFX (WS-X5111) 1 SC ATM (WS-X5154 and WS-X5155) 1 RJ-45 ATM (WS-X5153) 2 RJ-45 A/B CDDI ports (WS-X5103) 2 ST A/B FDDI singlemode ports, ST connectors (WS-X5104) with optical bypass switch: 6-pin mini-DIN 2 MIC A/B FDDI multimode ports, MIC connectors (WS-X5101) with optical bypass switch: 6-pin mini-DIN |
| Network management | SNMP8 agent Station Management (SMT) Specification, Revision 7.3 |
| Minimum Software Version Requirements for Modules | Module: Flash Download: Group Switching Ethernet Module Release 2.1 or above (10BaseT 48 Port) ATM LAN Emulation Module (UTP) or Release 1.5 or above ATM LAN Emulation Module (Single-Mode and Multimode Fiber) CDDI Module (UTP) Release 1.4 or above FDDI Module MMF (Multimode Fiber) or Release 1.4 or above FDDI Module SMF (Single-Mode Fiber) |
| SNMP v1 (RFC 1155-1157) SNMP MIB II (RFC 1213) Bridge MIB (RFC 1493) FDDI MIB, SMT 7.3 (RFC 1512) RFC 1516 (SNMP-REPEATER-MIB) Interface extension MIB (RFC 1573) Ethernet (RFC 1643) RFC 1757 (RMON MIB) CISCO-CDP-MIB Cisco Stack MIB CISCO-VTP-MIB | |
| ATM LAN Emulation Module Optical Specifications: Single Mode Fiber Multimode Fiber | Transmitter output power: -14 to -8 dBm Receiver sensitivity: -32.5 to -8 dBm Wavelength: 1261 to 1360 nm Optical source: Laser Maximum span: 10 km Transmitter output power: -19 to -14 dBm Receiver sensitivity: -32.5 to -14 dBm Wavelength: 1270 to 1380 nm Optical source: LED Maximum span: 2 km |
| FDDI Frame processing | IP Fragmentation (RFC 791) Translation (802.1h, 802.1i) Transparent bridging (802.1d) |
| Maximum station-to-station cabling distance | Fiber-optic supervisor engine module: Multimode: 1.2 miles (2 km), full-duplex; 121 feet (400 meters), half-duplex Single-mode: 9.3 miles (15 km), half- and full-duplex 10BaseFL, FDDI, and ATM 62.5/125-micron multimode fiber: 1.24 miles (2 km) 10BaseT Ethernet: Category 3-5 UTP1: 328' (100 m), 100 ohn STP: 238' (100 m) 10/100BaseTX Fast Ethernet: Category 5 UTP: 328' (100 m) 100BaseTX Fast Ethernet: Category 5 UTP: 328' (100 m) 100BaseFX Fast Ethernet 62.5/125-micron multimode fiber: 0.25 miles (400 m) half duplex 100BaseFX Fast Ethernet 62.5/125-micron multimode fiber: 1.24 miles (2 km) full duplex CDDI: Category 5 UTP: 328' (100 m) FDDI and ATM: 50/125-micron multimode fiber: 1.24 miles (2 km) FDDI: 8/125-micron single-mode fiber: 18.6 miles (32 km) ATM UTP: Category 5 UTP: 328' (100 m) ATM 8/125-micron single-mode fiber: 6.22 miles (10 km) |
| FDDI transmit power levels: Single-mode fiber Multimode fiber | Average optical power: Maximum: -4.0 dBm9 Minimum: -7.0 dBm Maximum: -14.0 dBm Minimum: -18.5 dBm |
| FDDI receive power levels: Single-mode fiber Multimode fiber | Average optical sensitivity: -33 dBm Average maximum input power: -14 dBm Average optical sensitivity: -34 dBm Average maximum input power: -14 dBm |
| Agency approvals | Safety: UL10 1950, CSA11-C22.2 No. 950-93, and EN60950 EMI12: FCC Class A (47 CFR, Part 15),CE Mark, EN55022 Class B and VCCI Class 2 with shielded UTP cables |
|
|