|
|
Product Numbers:
MEM-C5K-NAM-UPGD(=) Network Analysis Module 128-MB Upgrade Kit
This configuration note contains procedures for installing the 128-MB single inline memory module (SIMM) upgrade kit for the Catalyst 5000 family network analysis module.
This document contains the following sections:
The following tools are required to remove and replace the SIMM:
To install the SIMM, you must first remove the network analysis module from the switch.
 | Caution Always use an ESD wrist strap when handling modules or coming into contact with internal components. |
To remove a network analysis module, perform these steps:
 | Warning During this procedure, wear grounding wrist straps to avoid ESD damage to the module. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself. |
Step 1 Use a screwdriver to loosen the captive installation screws at the left and right sides of the module.
Step 2 Grasp the left and right ejector levers; simultaneously pull the left lever to the left and the right lever to the right to release the module from the backplane connector.
Step 3 As you pull the module out of the slot, place one of your hands under the carrier to support it. Avoid touching the module itself.
Step 4 Carefully pull the module straight out of the slot, keeping one hand under the carrier to guide it. Keep the module at a 90-degree orientation to the backplane (horizontal to
the floor).
Step 5 Place the removed module on an antistatic mat or antistatic foam.
The SIMM slots are located on the motherboard of the network analysis module (see Figure 2). Once you remove the network analysis module from the Catalyst 5000 family switch, you can install the SIMMs.
| Caution Always use an ESD wrist strap when handling modules or coming into contact with internal components. |
 | Caution Handle SIMMs by their edges only; avoid touching the memory module, pins, or traces (the metal fingers along the connector edge of a SIMM). SIMMs are sensitive components that are susceptible to ESD damage and can be damaged by mishandling. |
To remove and replace the SIMMs, refer to Figure 3 and perform the following steps for each of the two SIMMs:
Step 1 To remove a SIMM from its socket, pull the locking spring clips on both sides outward and tilt the SIMM free of the clips. Be careful not to break the clips on the SIMM connector.
Step 2 Hold the SIMM by its edges and gently lift and remove it, placing it on an antistatic mat or foam.
Step 3 Remove the replacement 128-MB SIMM set from its package, holding each SIMM by its edges, and carefully insert them, one at a time, into each connector so that they click into place.
When installing the network analysis module, it can be installed in slots 2 through 5 in the Catalyst 5000 and Catalyst 5505 switches, slots 2 through 9 of the Catalyst 5509 switch, and slots 2 through 12 of the Catalyst 5500 switch. There is a limit of one Network Analysis Module per chassis.
| Caution To prevent ESD damage, handle switching modules by the carrier edges only. |
Warning
During this procedure, wear grounding wrist straps to avoid ESD damage to the module. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself.
To install the network analysis module, follow these steps:
Step 1 Take the necessary precautions to prevent ESD damage.
Step 2 Hold the front panel of the network analysis module with one hand, and place your other hand under the carrier to support the module. Do not touch the printed circuit boards or connector pins (see Figure 4).
Step 3 Align the edges of the network analysis module carrier with the slot guides on the sides of the switch chassis.
Step 4 Pivot the two module ejector levers out away from the faceplate. The ejector levers are shown pivoted out in Figure 5.
Step 5 Keeping one hand under the carrier to guide the network analysis module, carefully slide it into the slot on the Catalyst 5000 family switch until the ejector levers click into place on the chassis. Be sure to keep the module horizontal to the backplane and avoid touching any of the components on the module.
Step 6 Using the thumb and forefinger of each hand, simultaneously pivot in both ejector levers, as shown in Figure 5, to fully seat the network analysis module in the backplane connector.
Step 7 Tighten the captive installation screws with a screwdriver.
Catalyst 5000 family modules, when intalled in a system, comply with the standards listed in Table 1:
| Specification | Description | |
Compliance | CE1 Marking |
|
Safety | UL2 1950, CSA3-C22.2 No. 950, EN460950, IEC5 950, TS6 001, AS/NZS7 3260 | |
EMI8 | FCC9 Class A (47 CFR10, Part 15), ICES11-003 Class A, EN55022 Class A, CISPR22 Class A, AS/NZS 3548 Class A, and VCCI12 Class A with UTP13 | |
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense.
You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures:
Modifications to this product not authorized by Cisco Systems could void the FCC approval and negate your authority to operate this product.
For more detailed installation and configuration information, refer to the following publications:
If you are reading Cisco product documentation on the World Wide Web, you can submit comments electronically. Click Feedback in the toolbar and select Documentation. After you complete the form, click Submit to send it to Cisco. We appreciate your comments.
Cisco Connection Online (CCO) is Cisco Systems' primary, real-time support channel. Maintenance customers and partners can self-register on CCO to obtain additional information and services.
Available 24 hours a day, 7 days a week, CCO provides a wealth of standard and value-added services to Cisco's customers and business partners. CCO services include product information, product documentation, software updates, release notes, technical tips, the Bug Navigator, configuration notes, brochures, descriptions of service offerings, and download access to public and authorized files.
CCO serves a wide variety of users through two interfaces that are updated and enhanced simultaneously: a character-based version and a multimedia version that resides on the World Wide Web (WWW). The character-based CCO supports Zmodem, Kermit, Xmodem, FTP, and Internet e-mail, and it is excellent for quick access to information over lower bandwidths. The WWW version of CCO provides richly formatted documents with photographs, figures, graphics, and video, as well as hyperlinks to related information.
You can access CCO in the following ways:
For a copy of CCO's Frequently Asked Questions (FAQ), contact cco-help@cisco.com. For additional information, contact cco-team@cisco.com.
Cisco documentation and additional literature are available in a CD-ROM package, which ships with your product. The Documentation CD-ROM, a member of the Cisco Connection Family, is updated monthly. Therefore, it might be more current than printed documentation. To order additional copies of the Documentation CD-ROM, contact your local sales representative or call customer service. The CD-ROM package is available as a single package or as an annual subscription. You can also access Cisco documentation on the World Wide Web at http://www.cisco.com, http://www-china.cisco.com, or http://www-europe.cisco.com.
If you are reading Cisco product documentation on the World Wide Web, you can submit comments electronically. Click Feedback in the toolbar and select Documentation. After you complete the form, click Submit to send it to Cisco. We appreciate your comments.
Posted: Mon Oct 18 16:57:02 PDT 1999
Copyright 1989-1999©Cisco Systems Inc.