Switch Route Processor and Line Module Specifications

The switch route processor and line module specifications are described in Table A-1.

For the five-slot switch chassis and common equipment specifications, refer to the appendix "System Chassis Specifications" in the Catalyst 8510 Campus Switch Router Chassis Installation Guide.

Table A-1: Switch Route Processor and Line Module Specifications

Description Specifications

Switch and processor capacity

10 Gbps shared memory, nonblocking switch fabric
up to 32 Kb frames

Dimensions (H x W x D)

1.2 x 14.4 x 16 in. (3.0 x 36.6 x 40.6 cm)

Weight

Processor: 6.85 lb (3.09 kg)
Modules: 3.55 lb (1.60 kg)

DC voltages supplied and steady-state maximum current ratings

System: +5V¹ @ 70A²
              +12V @ 2A
              +24V @ 0.2A
Processor:  +5V @ 15A
              +24V @ 25mA³
             +12V @ 500mA

Operating temperature

32 to 104ºF (0 to 40ºC)

Nonoperating temperature

-40 to 167ºF (-40 to 75ºC)

Humidity

10 to 90%, noncondensing

Altitude

-500 to 10,000 ft. (-52 to 3048 m)

Microprocessor

100-MHz MIP⁴ R4700

Memory

8-MB Flash memory SIMM⁵ (upgradable to 16 MB)
64-MB DRAM⁶
256-KB boot EPROM⁷
128-KB SRAM⁸
No Flash memory (PCMCIA⁹) card installed by default (accepts 8-, 16-, or 20-MB Intel Series 2+ Flash memory cards)

Management access

Standard Ethernet and dual EIA/TIA-232¹⁰ serial ports on the switch route processor

Interface ports

RJ-45 IEEE¹¹ 802.3 Ethernet 10BaseT port
   DB-25 EIA/TIA-232 auxiliary port and a
   DB-25 console port for an administration workstation

Line Modules

8 10/100BaseT Ethernet ports (RJ-45), 16K or 64K RAM
8 100BaseFX Ethernet ports (multimode fiber), 16K or 64K RAM
1 Gigabit Ethernet port, 16K or 64K RAM

Network management

Port TX¹² and RX¹³ LEDs, 10/100 operation and link LEDs
Switch and common equipment status LEDs
Multiple standard and Enterprise MIBs¹⁴
Text-based command-line interface based on familiar router interface
Standard Cisco IOS security capabilities: password and TACACS,¹⁵
Telnet, TFTP¹⁶, BOOTP

Management Information Bases (MIBs)

SNMP¹⁷ MIB II (RFC 1213)
Interface table MIB (RFC 1573)
CISCO-CDP-MIB
CISCO-BRIDGE-MIB

Maximum
Station-to-Station Cabling Distance

UTP¹⁸ cable: 328 ft (100 m) with four or fewer separate cable segments on the path;
50/125-micron and 62.5/125-micron multimode fiber: 1640 ft (500 m)

Fiber-Optic Power Levels:

1261 to 1360 nm¹⁹
Minimum: -15.0 dBm²⁰
Maximum: -8.0 dBm
Minimum: -28.0 dBm
Maximum: -8.0 dBm

Agency Approvals

UL²¹ 1950 (U.S.)
CSA²² 950 (Canada)
EN²³60950 (Germany)
IEC²⁴ 950 (International)
AS/NZS²⁵ 3260 (Australia/New Zealand)
CE Marking (European Union)
FCC²⁶ Part 15 (CFR 47) Class A (U.S.)
VCCI²⁷ Class A with UTP and Class B with shielded cables (Japan)
EN55022 Class A with UTP and Class B with shielded cables (European Union)
CISPR²⁸ 22 Class A with UTP and Class B with shielded cables (International)
AS/NZS 3548 Class A with UTP and Class B with shielded cables (Australia/New Zealand)

¹V = volts.
²A = amperes.
³mA = milliamperes.
⁴MIP = MultiChannel Interface Processor.
⁵SIMM = single in-line memory module.
⁶DRAM = dynamic random-access memory.
⁷EPROM = erasable programmable read-only memory.
⁸SRAM = static random-access memory.
⁹PCMCIA = Personal Computer Memory Card International Association.
¹⁰EIA/TIA = Electronic Industries Association/Telecommunications Industry Association.
¹¹IEEE = Institute of Electrical and Electronics Engineers.
¹²TX = transmit.
¹³RX = receive.
¹⁴MIBs = Management Information Bases.
¹⁵TACACS = Terminal Access Control Access System.
¹⁶TFTP = Trivial File Transfer Protocol.
¹⁷SNMP = Simple Network Management Protocol.
¹⁸UTP = unshielded twisted-pair.
¹⁹nm = nanometers.
²⁰dBm = decibel milliwatts.
²¹UL = Underwriters Laboratory.
²²CSA = Canadian Standards Association.
²³EN = European Norm.
²⁴IEC = International Eletrotechnical Commission.
²⁵AS/NZS = Australia/New Zealand Standards.
²⁶FCC = Federal Communications Commission.
²⁷VCCI = Voluntary Control Council for Interference.
²⁸CISPR = Comite International Special Des Perturbations Radioelectriques.

Description	Specifications
Switch and processor capacity	10 Gbps shared memory, nonblocking switch fabric up to 32 Kb frames
Dimensions (H x W x D)	1.2 x 14.4 x 16 in. (3.0 x 36.6 x 40.6 cm)
Weight	Processor: 6.85 lb (3.09 kg) Modules: 3.55 lb (1.60 kg)
DC voltages supplied and steady-state maximum current ratings	System: +5V¹ @ 70A² +12V @ 2A +24V @ 0.2A Processor: +5V @ 15A +24V @ 25mA³ +12V @ 500mA
Operating temperature	32 to 104ºF (0 to 40ºC)
Nonoperating temperature	-40 to 167ºF (-40 to 75ºC)
Humidity	10 to 90%, noncondensing
Altitude	-500 to 10,000 ft. (-52 to 3048 m)
Microprocessor	100-MHz MIP⁴ R4700
Memory	8-MB Flash memory SIMM⁵ (upgradable to 16 MB) 64-MB DRAM⁶ 256-KB boot EPROM⁷ 128-KB SRAM⁸ No Flash memory (PCMCIA⁹) card installed by default (accepts 8-, 16-, or 20-MB Intel Series 2+ Flash memory cards)
Management access	Standard Ethernet and dual EIA/TIA-232¹⁰ serial ports on the switch route processor
Interface ports	RJ-45 IEEE¹¹ 802.3 Ethernet 10BaseT port DB-25 EIA/TIA-232 auxiliary port and a DB-25 console port for an administration workstation
Line Modules	8 10/100BaseT Ethernet ports (RJ-45), 16K or 64K RAM 8 100BaseFX Ethernet ports (multimode fiber), 16K or 64K RAM 1 Gigabit Ethernet port, 16K or 64K RAM
Network management	Port TX¹² and RX¹³ LEDs, 10/100 operation and link LEDs Switch and common equipment status LEDs Multiple standard and Enterprise MIBs¹⁴ Text-based command-line interface based on familiar router interface Standard Cisco IOS security capabilities: password and TACACS,¹⁵ Telnet, TFTP¹⁶, BOOTP
Management Information Bases (MIBs)	SNMP¹⁷ MIB II (RFC 1213) Interface table MIB (RFC 1573) CISCO-CDP-MIB CISCO-BRIDGE-MIB
Maximum Station-to-Station Cabling Distance	UTP¹⁸ cable: 328 ft (100 m) with four or fewer separate cable segments on the path; 50/125-micron and 62.5/125-micron multimode fiber: 1640 ft (500 m)
Fiber-Optic Power Levels:	1261 to 1360 nm¹⁹ Minimum: -15.0 dBm²⁰ Maximum: -8.0 dBm Minimum: -28.0 dBm Maximum: -8.0 dBm
Agency Approvals	UL²¹ 1950 (U.S.) CSA²² 950 (Canada) EN²³60950 (Germany) IEC²⁴ 950 (International) AS/NZS²⁵ 3260 (Australia/New Zealand) CE Marking (European Union) FCC²⁶ Part 15 (CFR 47) Class A (U.S.) VCCI²⁷ Class A with UTP and Class B with shielded cables (Japan) EN55022 Class A with UTP and Class B with shielded cables (European Union) CISPR²⁸ 22 Class A with UTP and Class B with shielded cables (International) AS/NZS 3548 Class A with UTP and Class B with shielded cables (Australia/New Zealand)

Table of Contents

Switch Route Processor and Line Module Specifications

Switch Route Processor and Line Module Specifications