|
|
This guide is written for anyone who installs or operates Cisco DSLAMs with NI-2. This includes the:
This guide includes 17 chapters and an index. They are:
| Chapter | Title | Content |
Chapter 1 | Describes the DSLAM user interface and provides instructions for using the command-line interface. Describes how to access and list the commands available in each command mode, and explains the primary uses for each command mode. | |
Chapter 2 | Explains how to configure lines, modems, and terminal settings to access the ATM switch for management purposes. | |
Chapter 3 | Describes the initial configuration of the LightStream 1010 ATM switch. | |
Chapter 4 | Describes the basic tasks for configuring general DSLAM system features, such as access control and basic switch management. | |
Chapter 5 | Describes how to configure virtual connections (VCs) in a typical ATM network after autoconfiguration has established the default network connections. The network configuration modifications described in this chapter are used to optimize your ATM network operation. | |
Chapter 6 | Describes OAM fault management and performance management functions at the ATM management (M)-plane layer of the Cisco DSLAMs with NI-2. | |
Chapter 7 | Describes how to configure the DSLAM for Digital Subscriber Line (DSL) service. | |
Chapter 8 | Describes how to explicitly configure ATM network interface types. Explicitly configuring interfaces is the alternative to Interim Local Management Interface (ILMI) autoconfiguration, which senses the peer interface type and appropriately configures the DSLAM interface. | |
Chapter 9 | Describes resource management, which involves modeling and managing switch, interface, and connection resources. | |
Chapter 10 | Describes the Integrated Local Management Interface (ILMI) protocol implementation within the DSLAM. | |
Chapter 11 | Describes the Interim Interswitch Signaling Protocol (IISP) and Private Network-Network Interface (PNNI) ATM routing protocol implementations on the DSLAM. | |
Chapter 12 | Describes how to configure and maintain access control lists, which are used to permit or deny incoming calls or outgoing calls on an interface of the DSLAM. | |
Chapter 13 | Describes how to configure in-band management for the DSLAM. | |
Chapter 14 | Describes the ATM accounting and remote monitoring (RMON) features used with the DSLAM. | |
Chapter 15 | Describes how to configure DSLAM signaling features. | |
Chapter 16 | Describes the steps required to configure the trunk and subtended interfaces on the DSLAM NI-2 card. | |
Chapter 17 | Describes how to load and maintain system software images and configuration files. | |
Index |
|
|
Screen displays use this convention:
|
|
Command descriptions use these conventions:
|
|
|
|
|
|
|
|
Examples use these conventions:
|
|
|
|
|
|
|
|
Notes, examples, time savers, tips, cautions, and warnings use these conventions:
 |
Note Means reader take note. Notes contain helpful suggestions or references to material not covered in the publication. |
 |
Caution Means reader be careful. In this situation, you might do something that could result in equipment damage or loss of data. |
The software described in this guide runs on several Cisco DSLAM platforms, including the Cisco 6160, the Cisco 6260, and the Cisco 6130. This section lists hardware documents for each platform and software documents for all the platforms.
This section lists the documents for each NI-2 DSLAM platform. In general, you should use the hardware documentation that was shipped to you with your equipment.
These documents contain hardware information that might be useful to Cisco 6160 users:
These documents contain hardware information that might be useful to Cisco 6260 users:
These documents contain hardware information that might be useful to Cisco 6130 users:
These documents contain software information for all NI-2 DSLAMs:
In these ATM software manuals, look for information pertaining to the LightStream 1010, which uses the same software base as the NI-2 DSLAMs:
You can obtain documentation from the following sources:
You can access the most current Cisco documentation on the World Wide Web at http://www.cisco.com, http://www-china.cisco.com, or http://www-europe.cisco.com.
Cisco documentation and additional literature are available in a CD-ROM package, which ships with your product. The Documentation CD-ROM is updated monthly. Therefore, it is probably more current than printed documentation. The CD-ROM package is available as a single unit or as an annual subscription.
Registered CCO users can order the Documentation CD-ROM and other Cisco Product documentation through our online Subscription Services at http://www.cisco.com/cgi-bin/subcat/kaojump.cgi.
Nonregistered CCO users can order documentation through a local account representative by calling Cisco's corporate headquarters (California, USA) at 408 526-4000 or, in North America, call 800 553-NETS (6387).
Cisco provides Cisco Connection Online (CCO) as a starting point for all technical assistance. Warranty or maintenance contract customers can use the Technical Assistance Center. All customers can submit technical feedback on Cisco documentation using the web, e-mail, a self-addressed stamped response card included in many printed docs, or by sending mail to Cisco.
Cisco continues to revolutionize how business is done on the Internet. Cisco Connection Online is the foundation of a suite of interactive, networked services that provides immediate, open access to Cisco information and resources at anytime, from anywhere in the world. This highly integrated Internet application is a powerful, easy-to-use tool for doing business with Cisco.
CCO's broad range of features and services helps customers and partners to streamline business processes and improve productivity. Through CCO, you will find information about Cisco and our networking solutions, services, and programs. In addition, you can resolve technical issues with online support services, download and test software packages, and order Cisco learning materials and merchandise. Valuable online skill assessment, training, and certification programs are also available.
Customers and partners can self-register on CCO to obtain additional personalized information and services. Registered users may order products, check on the status of an order and view benefits specific to their relationships with Cisco.
You can access CCO in the following ways:
You can e-mail questions about using CCO to cco-team@cisco.com.
The Cisco Technical Assistance Center (TAC) is available to warranty or maintenance contract customers who need technical assistance with a Cisco product that is under warranty or covered by a maintenance contract.
To display the TAC web site that includes links to technical support information and software upgrades and for requesting TAC support, use www.cisco.com/techsupport.
To contact by e-mail, use one of the following:
Language | E-mail Address |
|---|---|
|
|
|
|
|
|
|
|
|
|
|
|
In North America, TAC can be reached at 800 553-2447 or 408 526-7209. For other telephone numbers and TAC e-mail addresses worldwide, consult the following web site: http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml.
If you are reading Cisco product documentation on the World Wide Web, you can submit technical comments electronically. Click Feedback in the toolbar and select Documentation. After you complete the form, click Submit to send it to Cisco.
You can e-mail your comments to bug-doc@cisco.com.
To submit your comments by mail, for your convenience many documents contain a response card behind the front cover. Otherwise, you can mail your comments to the following address:
Cisco Systems, Inc.
Document Resource Connection
170 West Tasman Drive
San Jose, CA 95134-9883
We appreciate and value your comments.
Posted: Tue Sep 19 10:53:31 PDT 2000
Copyright 1989-2000©Cisco Systems Inc.