|
|
This appendix provides the technical specifications for the Cisco 6100 with NI-2 system. The appendix contains the following sections:
 |
Note For information on site and safety requirements, see "Preparing for Installation." |
This section details the specifications for the following hardware components:
Table A-1 lists the hardware specifications of the Cisco 6100 with NI-2 system.
| Specification | Description | ||||
|---|---|---|---|---|---|
9 RUs1--23 in. x 15.75 in. x 12 in. (58.42 cm x 40.005 cm x 30.48 cm) | |||||
Empty--approximately 31 lb (14.06 kg) | |||||
Network interface | |||||
CAP--Up to 7.168 Mbps downstream/1.088 Mbps upstream | |||||
Console terminal connection on the NI-2 card | |||||
Management access |
| ||||
External alarm contacts | Single dry contact alarm input (NO) | ||||
Power requirements |
| ||||
CO operating requirements | Temperature | 41 to 104ºF (5 to 40ºC)--Operating | |||
Subtending | NI-2 card | ||||
| 1RU = rack unit. An RU is equal to 1.75 inches (4.45 cm). |
Table A-2 lists the specifications for the 4xflexi.
| Specification | DMT-2 Mode | CAP Mode | G.lite Mode |
|---|---|---|---|
Standards supported | ITU G.dmt (G.992.1) | RADSL1 | ITU G.lite (G.992.2) |
Power consumption | 17.5W | 13.5W | 13.5W |
Maximum data rates (per port)
| 8.032 Mbps 864 kbps | 7.168 Mbps 1.088 Mbps | 1.536 Mbps 512 kbps |
External interfaces | 4 (no connectors on card) | ||
Internal hardware | AMD 186-based 3.3V 18-MHz CPU 128-KB SRAM 512K flash | ||
Dimensions | Height: 6.07 in. (15.42 cm) | ||
Weight | 0.875 lb (0.4 kg) | ||
| 1Rate-adaptive digital subscriber line. |
Table A-3 lists the specifications for the DS3/2DS3 NI-2 card.
| Specification | Description |
Internal hardware | 150 MHz RC64475 CPU |
Dimensions | Height: 12.38 in. (31.45 cm) |
Weight | 3.0 lb (1.36 kg) |
Level 2 protocol | ATM |
External interfaces | Three DS3 (44.736 Mbps) coaxial ports |
Connector type | BNC1 |
Impedance | 75 ohms (nominal) |
Line encoding | B3ZS |
Framing | C-bit parity, optionally PLCP with M23, otherwise Add Drop Multiplexer (ADM) |
Power consumption | 33.5W |
| 1The Bayonet-Neill-Concelman (BNC) connectors are located on the system I/O card which is installed on the backplane of the chassis. |
Table A-4 lists the specifications of the single-mode and multimode versions of the OC-3c/OC-3c NI-2 card.
| Specification | Description | |
Internal hardware | 150 MHz RC64475 CPU | |
Dimensions | Height: 12.38 in. (31.45 cm) | |
Weight | 3.0 lb (1.36 kg) | |
Level 2 protocol | ATM | |
Power consumption | 33.5W | |
| Single Mode Card | Multimode Card | |
External interfaces | Two OC-3c/STM-1 (155 Mbps) single-mode ports | Two OC-3c/STM-1 (155 Mbps) multimode ports |
Connector type | SC-PC | SC-PC |
Fiber type | Intermediate reach single mode | Multimode |
Average transmitted power | -15 to -8 dBm | -20 to -14 dBm |
Average received power | -8 dBm | -11 dBm |
Transmission distance | Up to 20 km (12 miles) | Up to 2 km (1.2 miles) |
Wavelength | 1310 nm | 1300 nm |
Table A-5 lists Cisco 6100 with NI-2 system software specifications.
| Specification | Description |
|---|---|
Management protocols | IOS software support for SNMP to CEMF1 |
Management applications | |
Management interfaces | In band--ATM VC Out of band--10BaseT Ethernet, console, auxiliary |
| 1CEMF = Cisco Element Management Framework 2IOS = Internet Operating System 3CDM = Cisco DSL Manager |
Posted: Fri Aug 11 15:12:49 PDT 2000
Copyright 1989-2000©Cisco Systems Inc.