|
|
This chapter provides the requirements necessary to prepare for the installation of the Cisco 6100 Series system.
The chapter contains the following sections:
 |
Caution Before you start the installation procedures, read the entire chapter for important information and safety warnings. |
This section describes safety requirements for the Cisco 6100 with NI-1 system. Before you install the Cisco 6100 with NI-1 system, ensure that all the criteria in this section are met. The section describes the following safety requirements:
 |
Note To see translations of the warnings that appear in this publication, refer to the Regulatory Compliance and Safety Information for the Cisco 6100 Series System document that accompanied this product. |
 |
Tips In the following warnings, the terms cover panel and safety cover refer to the Cisco 6100/6130 chassis front cover. |
|
Caution Before you start the installation procedures, read the entire chapter for important information and safety warnings. |
|
Caution Proper ESD protection is required whenever you handle Cisco digital subscriber line access multiplexer (DSLAM) equipment. Installation and maintenance personnel should be properly grounded using ground straps to eliminate the risk of ESD damage to the equipment. Modules are subject to ESD damage whenever they are removed from the chassis. |
|
Caution Be careful when you remove the standoff screws and reinsert the screws into the screw holes on the backplane so that the backplane circuitry does not become damaged. |
|
Caution Installing the modules in the chassis with the power leads reversed can damage the modules. |
|
Caution If fuses are already installed in the fuse and alarm panel, remove them. You can replace the fuses after the system is installed. Do not power up the system while you install and connect the system. |
|
Caution If the power connections are improperly connected and power is applied while the modules are installed, the modules and chassis could be damaged. |
|
Caution Any card or module that is only partially connected to the backplane can disrupt system operation. |
 |
Warning The customer 48 volt power system must provide reinforced insulation between the primary AC power and the 48 VDC output. |
|
Warning There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. |
|
Warning Two people are required to lift the chassis. Grasp the chassis underneath the lower edge and lift with both hands. To prevent injury, keep your back straight and lift with your legs, not your back. |
|
Warning To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure that the system remains stable. The following guidelines are provided to ensure your safety: ---This unit should be mounted at the bottom of the rack if it is the only unit in the rack. ---When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest component at the bottom of the rack. ---If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack. |
|
Warning Class 1 laser product. |
|
Warning Use copper conductors only. |
|
Warning A readily accessible two-poled disconnect device must be incorporated in the fixed wiring. |
|
Warning The DS3 ports are not intended to be connected to cables that run outside the building where it is installed. For any connections outside the building, the DS3 ports must be connected to a network termination unit (NTU). NTU devices should comply with appropriate national safety standards such as UL 1950, CSA 950, EN 60950, IEC 950, and AS 3260. |
|
Warning Never install telephone wiring during an electrical storm. |
|
Warning Do not reach into a vacant slot or chassis while you install or remove a module or a fan. Exposed circuitry could constitute an energy hazard. |
|
Warning Ethernet cables must be shielded when used in a central office environment. |
|
Warning An exposed wire lead from a DC-input power source can conduct harmful levels of electricity. Be sure that no exposed portion of the DC-input power source wire extends from the terminal block plug. |
|
Warning Blank faceplates and cover panels serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all cards, faceplates, and front covers are in place. |
|
Warning When installing the unit, the ground connection must always be made first and disconnected last. |
|
Warning This equipment is intended to be grounded. Ensure that the host is connected to earth ground during normal use. |
|
Warning This equipment needs to be grounded. Use a green and yellow 12 to 14 American Wire Gauge (AWG) ground wire to connect the host to earth ground during normal use. |
|
Warning Incorrect connection of this or connected equipment to a general purpose outlet could result in a hazardous situation. |
|
Warning Read the installation instructions before you connect the system to its power source. |
|
Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. |
|
Warning The ISDN connection is regarded as a source of voltage that should be inaccessible to user contact. Do not attempt to tamper with or open any public telephone operator (PTO)-provided equipment or connection hardware. Any hardwired connection (other than by a nonremovable, connect-one-time-only plug) must be made only by PTO staff or suitably trained engineers. |
|
Warning Do not stare into the beam or view it directly with optical instruments. |
|
Warning Do not work on the system or connect or disconnect cables during periods of lightning activity. |
|
Warning Systems using a Cisco 6100 chassis must connect to the network through a POTS splitter to provide the secondary lightning protection. |
|
Warning Use caution when installing or modifying telephone lines. |
|
Warning This unit has more than one power supply connection; all connections must be removed completely to completely remove power from the unit. |
|
Warning To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord. |
|
Warning To prevent the system from overheating, do not operate it in an area that exceeds the maximum recommended ambient temperature of 104°F (40°C) |
|
Warning Metal objects heat up when connected to power and ground, and can cause serious burns. |
|
Warning Secure all power cabling when installing this unit to avoid disturbing field-wiring connections. |
|
Warning The power supply circuitry for the equipment can constitute an energy hazard. Before you install or replace the equipment, remove all jewelry (including rings, necklaces, and watches). Metal objects can come into contact with exposed power supply wiring or circuitry inside the DSLAM equipment. This could cause the metal objects to heat up and cause serious burns or weld the metal object to the equipment. |
|
Warning Ultimate disposal of this product should be handled according to all national laws and regulations. |
|
Warning This unit is intended for installation in restricted access areas. A restricted access area is where access can only be gained by service personnel through the use of a special tool, lock and key, or other means of security, and is controlled by the authority responsible for the location |
|
Warning Connect the unit only to DC power source that complies with the Safety Extra-Low Voltage (SELV) requirements in IEC 60950 based safety standards. |
|
Warning This product requires short-circuit (overcurrent) protection, to be provided as part of the building installation. Install only in accordance with national and local wiring regulations. |
|
Warning Care must be given to connecting units to the supply circuit so that wiring is not overloaded. |
|
Warning Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. |
|
Warning Do not use a telephone to report a gas leak in the vicinity of the leak. |
|
Warning Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. |
|
Warning Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. |
|
Warning This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions. |
|
Warning Do not use this product near water; for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool. |
|
Warning During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself. |
This section covers the following topics:
|
Caution Any card or module that is only partially connected to the backplane can disrupt system operation. |
This section describes requirements for the site in which the Cisco 6100 with NI-1 system will be installed. Before you install the Cisco 6100 with NI-1 system, ensure that all the criteria in this section are met. The section describes the following:
The system can tolerate a wide range of temperatures. Table 2-1 provides the Cisco recommendations for temperature, altitude, and humidity conditions in a CO environment.
| Environmental Specifications | Description |
|---|---|
Temperature | 41 to 104ºF (5 to 40ºC)---Operating |
|
Warning To prevent the system from overheating, do not operate it in an area that exceeds the maximum recommended ambient temperature of 104°F (40°C) |
The following hardware locations ensure proper ventilation for the Cisco 6100 with NI-1 system:
You can install a combination of the Cisco 6100 with NI-1 system components in a 7-foot rack:
|
Warning Systems using a Cisco 6100 chassis must connect to the network through a POTS splitter to provide the secondary lightning protection. |
The Cisco 6100 with NI-1 system fits in a 23-inch wide rack. See Table 2-2 for individual rack space requirements.
| Component | Rack Space | Height | Depth |
|---|---|---|---|
Cisco 6100 chassis | 9 RUs1 | 15.75 in. (40.00 cm) | 12 in. (30.48 cm) |
Cisco 6110 chassis | 4 RUs | 7 in. (17.78 cm) | 12 in. (30.48 cm) |
Cisco 6120 chassis | 4 RUs | 7 in. (17.78 cm) | 12 in. (30.48 cm) |
| 1An RU is equal to 1.75 inches (4.45 cm). |
Depending on your configuration type, plan accordingly so that the central office (CO) rack accommodates your needs. Use Table 2-3 to calculate the rack space necessary for your Cisco 6100 with NI-1 system configuration. The total amount of rack space should not exceed 42 RUs. If your total configuration exceeds 42 RUs, either replan your configuration or use more than one rack to house the Cisco 6100 with NI-1 system components.
| Line | Instructions | Calculation |
|---|---|---|
| 1 | Total number of Cisco 6100 chassis in the rack---One per DOH configuration (include subtending host and subtended node chassis). |
|
| 2 | Total number of Cisco 6110 chassis in the rack---Up to five per DOH configuration. |
|
| 3 | Total number of Cisco 6120 chassis in the rack---Must equal line 2. |
|
| 4 | Multiply 9 RUs by the total number of chassis on line 1. |
|
| 5 | Enter 1 RU on line 5 for the 1 RU of space required between the Cisco 6100 and the Cisco 6110. |
|
| 6 | Multiply 4 RUs by the total number of chassis on line 2. |
|
| 7 | Multiply 4 RUs by the total number of chassis on line 3. |
|
| 8 | Add lines 4 through 7 for the total number of RUs needed with your DOH configuration. |
|
The central office (CO) power source or rectifier supplies external power to the system as -48 VDC from the fuse and alarm panel. Power connections from the fuse and alarm panel are wired separately to the Cisco 6100 chassis. Connections for single- and dual-power feeds are provided. The power input connections are redundant, and only one is absolutely necessary for system operation. The nominal voltage is -48 VDC; the minimum operating value is -36 VDC; and the maximum operating value is -60 VDC.
Before you connect the system to a power source, verify that the power source is properly grounded and it falls within the internal power supply rating.
Depending on your configuration type, calculate the typical power required for each Cisco 6100 Series component. After you calculate the typical power, determine the minimum fuse value for each component that is wired to the fuse and alarm panel. Use Table 2-4 to calculate the minimum fuse rating that is necessary for each of your Cisco 6100 with NI-1 system components.
|
Note The power rating label that is supplied on the rear of each chassis and fan tray indicates the maximum fuse value for the chassis or the fan tray. |
| Component | Instructions | Calculation |
|---|---|---|
| Cisco 61001,2 | ||
| 1 | Multiply 8.5W by the total number of CAP ATU-C modules to add to the Cisco 6100.3 |
|
| 2 | Enter 10W for the DS3 STM4 for the subtending host (if you are installing a subtended network). |
|
| 3 | Enter 51W for the DS3 or OC-3c NI-1 module. |
|
| 4 | Enter 9W for the system controller module. |
|
| 5 | Add lines 1, 2, 3, and 4. This is the typical power required for the Cisco 6100. |
|
| 6 | Divide line 5 by 48. This is the nominal current for the Cisco 6100. |
|
| 7 |
| |
| Cisco 6110 | ||
| 8 | Enter 25W for the Cisco 6110. |
|
| 9 | Divide line 8 by 48. This is the nominal current for the Cisco 6110. |
|
| 10 |
| |
For detailed information on the required cables, refer to "Cable and Port Mapping Specifications."
|
Warning To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure that the system remains stable. The following guidelines are provided to ensure your safety: ---This unit should be mounted at the bottom of the rack if it is the only unit in the rack. ---When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest component at the bottom of the rack. ---If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack. |
Cisco recommends that you mount the Cisco 6100 with NI-1 system in a rack. Ensure that vertical hole spacing on the rack rails meets standard EIA-310-C requirements---1 inch (2.54 cm) spacing. All portions of the rack are equal to or less than the NEBS maximum allowances of 12 inches (30.48 cm).
When you install the Cisco 6100 with NI-1 system in a rack, be sure to allow enough room to access the backplane of the unit for wiring and cabling purposes. The majority of the connectors are located on the backplane.
Table 2-5 lists the tools and equipment required to install and remove the Cisco 6100 with NI-1 system components:
| Check | Tools and Equipment | ||
|---|---|---|---|
| Hardware Components | ||
| Cisco 6100 chassis | ||
|
| ||
|
| ||
|
| ||
|
| ||
|
| ||
|
| ||
| Cisco 6110 chassis | ||
|
| ||
|
| ||
| Cisco 6120 chassis | ||
|
| ||
| Rear cover (optional) | ||
| Front cover | ||
| Cables (see "Cable and Port Mapping Specifications." for cable information) | ||
| Software Components | ||
| ViewRunner for Windows or ViewRunner for HP OpenView | ||
| Tools | ||
| A 3/16-inch flat-head screwdriver | ||
| A Phillips-head screwdriver | ||
| A one-quarter inch socket driver or wrench | ||
| Necessary equipment for ESD protection---Required whenever you handle Cisco DSLAM equipment, which includes the chassis, modules, and cards | ||
| Mounting screws---To mount the Cisco 6100, Cisco 6110, and Cisco 6120 to the rack | ||
| Standoff screws | ||
| Backplane screws---Included on the backplane | ||
| Two plastic ESD shields for the system I/O card and the DS3 subtending I/O card---Included with the cards | ||
| Wire-wrapping tool | ||
| Wire stripper | ||
|
| ||
| Ferrites that yield an impedance of 200 ohms +/-20 percent at 100 MHz
| ||
| Tie wraps | ||
|
| ||
|
| 1LIM = line interface module. |
Two people are needed for lifting, installing, and removing a chassis and some of its components (for example, the rear cover).
|
Note The Cisco 6100 with NI-1 system has no internal user-serviceable parts. However, you can add or remove a chassis module or a fan module without removing power from the system (hot swapping). |
|
Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. |
Each Cisco 6100 with NI-1 system chassis is securely packaged in a shipping box. The Cisco 6100 with NI-1 system components ship either:
The module antistatic carriers ship together in a box. The NI-1 module is packed in its own antistatic bag, which is housed in foam inserts and shipped in a separate box.
|
Caution Proper ESD protection is required whenever you handle Cisco DSLAM equipment. Installation and maintenance personnel should be properly grounded using ground straps to eliminate the risk of ESD damage to the equipment. Modules are subject to ESD damage whenever they are removed from the chassis. |
To unpack the Cisco 6100 with NI-1 system, complete the following steps:
Step 2 Carefully open the box.
Step 3 Remove all packing material.
Step 4 Remove the chassis from the box.
|
Warning Two people are required to lift the chassis. Grasp the chassis underneath the lower edge and lift with both hands. To prevent injury, keep your back straight and lift with your legs, not your back. |
Step 5 Carefully open the additional boxes, remove the packing material, and remove the modules.
Step 6 Open the accessory kits and boxes that contain the cables, ferrites, documentation, and management software. Do not use a knife to open these boxes.
To verify that all equipment, cables, documentation, and so forth are received, compare the packing list to your shipment and to your order. If any items are missing or you need additional information, contact the Cisco Technical Assistance Center (TAC) at one of the following:
After you verify that all of the equipment is included, carefully examine the assemblies, modules, and cables for any damage resulting from shipping. If you suspect any damage from shipping, contact your local freight carrier for procedures on damage claims.
If you observe any physical defects in the items you ordered, obtain standard warranty service by delivering the defective part, accompanied by a copy of the dated proof-of-purchase, to the Cisco Systems Corporate Service Center or an Authorized Cisco Systems Service Center during the applicable warranty period. Contact the Cisco TAC for the location of your nearest service center.
See the back of the title page for the Cisco Systems warranty information for hardware and software products.
Posted: Fri Jun 9 07:19:18 PDT 2000
Copyright 1989 - 2000©Cisco Systems Inc.