Table of Contents

B.1 Multiplexer Chassis Connectors

B.1.1 xDSL Connectors
B.1.2 Terminal Block Connector
B.1.3 Alarm Contacts

B.2 Port Mapping Tables

B.2.1 Direct Connect with PSC Configuration Port Mapping Tables
B.2.2 Direct Connect without PSC Configuration Port Mapping Tables
B.2.3 Siecor POTS Splitter Port Mapping Table
B.2.4 Port Mapping Table for Building MC Cables

B.3 Standard Telco Color Chart

Connectors, Pinouts, and Port Mapping

This appendix provides connectors, pinouts, and port mapping tables for a Direct Connect configuration of the Cisco 6100 Series system.

For a list of Direct Connect configuration cables and their respective Cisco part numbers, see "Cabling for a Direct Connect Configuration."

B.1 Multiplexer Chassis Connectors

This section describes multiplexer chassis (MC) connectors and pinouts for the following:

• xDSL Connectors

• Terminal Block Connector

• Alarm Contacts

B.1.1 xDSL Connectors

The backplane of the MC contains six Champ connectors which connect to the xTU-C twisted-pair subscriber data interface. This connection can be made by either of the following:

Figure B-1 shows connector pin locations for the xDSL Champ connectors. Pin locations are the same for all Champ connectors.

B.1.2 Terminal Block Connector

Use the terminal block connector to wire the MC to the power source on the fuse and alarm panel. For more information on fusing, see one of the following:

• The "Attach MC Power Connections" section for a Direct Connect with a PSC configuration

• The "Attach MC Power Connections" section for a Direct Connect without a PSC configuration

The terminal block connectors will accept 14 to 18 American Wire Gauge (AWG) copper solid or stranded wire. Figure B-2 shows the Cisco 6100 Series power terminal block.

B.1.3 Alarm Contacts

The Cisco 6100 Series system provides alarm contacts for audible, visual, and E2A alarm connections. These contacts support minor, major, and critical alarm reporting. (Figure B-3 shows the alarm contacts.)

Table B-1 lists the alarm contact pinouts shown in Figure B-3.

Table B-1: Alarm Contact Pinouts

Connector	Pin	Signal
E2A P14	1	Critical_E2+
	2	Critical_E2-
	3	Major_E2+
	4	Major_E2-
	5	Minor_E2+
	6	Minor_E2-
	7	Fan Alarm+
	8	Fan Alarm-
Visual P15	1	Critical_V+
	2	Critical_V-
	3	Major_V+
	4	Major_V-
	5	Minor_V+
	6	Minor_V-
	7	ACO_IN_V (future)
	8	ACO_RTN_V (future)
Audible P17	1	Critical_A+
	2	Critical_A-
	3	Major_A+
	4	Major_A-
	5	Minor_A+
	6	Minor_A-
	7	ACO_IN_A
	8	ACO_RTN_A

• The "Connect the Alarm Contacts" section for a Direct Connect with a PSC configuration

• The "Connect the Alarm Contacts" section for a Direct Connect without a PSC configuration

B.2 Port Mapping Tables

This section provides port mapping tables which show the wire pair and chassis port assignments for the following:

• Direct Connect with a PSC configuration

• Direct Connect without a PSC configuration

• Siecor POTS splitter

• Building your own MC cables

B.2.1 Direct Connect with PSC Configuration Port Mapping Tables

Table B-2 maps the MC ports, the PSC ports, and the wire pairs when using the one-to-one cables (see Table 3-2) for a Direct Connect with a PSC configuration. The corresponding cable kit number is CAB-61-014.

Table B-2: Port Mapping for One-to-One Cables in a Direct Connect with PSC Configuration

MC Slot/Line	PSC Slot/Line	Champ Pins		PSC MDF1/POTS Connection
		Tip	Ring
1/1	1/1	9	34	J11/J7
1/2	1/2	10	35
2/1	1/3	11	36
2/2	1/4	12	37
3/1	2/1	5	30
3/2	2/2	6	31
4/1	2/3	7	32
4/2	2/4	8	33
5/1	3/1	1	26
5/2	3/2	2	27
6/1	3/3	3	28
6/2	3/4	4	29
7/1	4/1	18	43
7/2	4/2	19	44
8/1	4/3	20	45
8/2	4/4	21	46
13/1	19/1	18	43	J14/J8
13/2	19/2	19	44
14/1	19/3	20	45
14/2	19/4	21	46
15/1	20/1	1	26
15/2	20/2	2	27
16/1	20/3	3	28
16/2	20/4	4	29
17/1	21/1	5	30
17/2	21/2	6	31
18/1	21/3	7	32
18/2	21/4	8	33
19/1	22/1	9	34
19/2	22/2	10	35
20/1	22/3	11	36
20/2	22/4	12	37
21/1	5/1	22	47	J11/J7
21/2	5/2	23	48
22/1	5/3	24	49
22/2	5/4	25	50
23/1	6/1	6	31	J12/J9
23/2	6/2	7	32
24/1	6/3	8	33
24/2	6/4	9	34
25/1	7/1	2	27
25/2	7/2	3	28
26/1	7/3	4	29
26/2	7/4	5	30
27/1	8/1	1	26
27/2	8/2	10	35
28/1	8/3	11	36
28/2	8/4	12	37
31/1	15/1	1	26	J13/J10
31/2	15/2	10	35
32/1	15/3	11	36
32/2	15/4	12	37
33/1	16/1	2	27
33/2	16/2	3	28
34/1	16/3	4	29
34/2	16/4	5	30
35/1	17/1	6	31
35/2	17/2	7	32
36/1	17/3	8	33
36/2	17/4	9	34
37/1	18/1	22	47	J14/J8
37/2	18/2	23	48
38/1	18/3	24	49
38/2	18/4	25	50

1MDF = main distribution frame

Table B-3 maps the MC ports, the PSC ports for two PSCs, and the wire pairs when using the two-to-one cables (see Table 3-3) for a Direct Connect with a PSC configuration. The corresponding cable kit number is CAB-MC128-PSC80. You can use the two-to-one cables to connect one MC to two PSCs for systems using quad-port ATU-C modules.

Table B-3: Port Mapping for Two-to-One Cables in a Direct Connect with PSC Configuration

MC Slot/Line	PSC Slot/Line		Champ Pins		PSC MDF/ POTS Connection
	PSC 1	PSC 2	Tip	Ring
1/1	1/1	---	9	34	J11/J7
1/2	1/2	---	10	35
1/3	---	1/1	9	34
1/4	---	1/2	10	35
2/1	1/3	---	11	36
2/2	1/4	---	12	37
2/3	---	1/3	11	36
2/4	---	1/4	12	37
3/1	2/1	---	5	30
3/2	2/2	---	6	31
3/3	---	2/1	5	30
3/4	---	2/2	6	31
4/1	2/3	---	7	32
4/2	2/4	---	8	33
4/3	---	2/3	7	32
4/4	---	2/4	8	33
5/1	3/1	---	1	26
5/2	3/2	---	2	27
5/3	---	3/1	1	26
5/4	---	3/2	2	27
6/1	3/3	---	3	28
6/2	3/4	---	4	29
6/3	---	3/3	3	28
6/4	---	3/4	4	29
7/1	4/1	---	18	43
7/2	4/2	---	19	44
7/3	---	4/1	18	43
7/4	---	4/2	19	44
8/1	4/3	---	20	45
8/2	4/4	---	21	46
8/3	---	4/3	20	45
8/4	---	4/4	21	46
13/1	19/1	---	18	43	J14/J8
13/2	19/2	---	19	44
13/3	---	19/1	18	43
13/4	---	19/2	19	44
14/1	19/3	---	20	45
14/2	19/4	---	21	46
14/3	---	19/3	20	45
14/4	---	19/4	21	46
15/1	20/1	---	1	26
15/2	20/2	---	2	27
15/3	---	20/1	1	26
15/4	---	20/2	2	27
16/1	20/3	---	3	28
16/2	20/4	---	4	29
16/3	---	20/3	3	28
16/4	---	20/4	4	29
17/1	21/1	---	5	30
17/2	21/2	---	6	31
17/3	---	21/1	5	30
17/4	---	21/2	6	31
18/1	21/3	---	7	32
18/2	21/4	---	8	33
18/3	---	21/3	7	32
18/4	---	21/4	8	33
19/1	22/1	---	9	34
19/2	22/2	---	10	35
19/3	---	22/1	9	34
19/4	---	22/2	10	35
20/1	22/3	---	11	36
20/2	22/4	---	12	37
20/3	---	22/3	11	36
20/4	---	22/4	12	37
21/1	5/1	---	22	47	J11/J7
21/2	5/2	---	23	48
21/3	---	5/1	22	47
21/4	---	5/2	23	48
22/1	5/3	---	24	49
22/2	5/4	---	25	50
22/3	---	5/3	24	49
22/4	---	5/4	25	50
23/1	6/1	---	6	31	J12/J9
23/2	6/2	---	7	32
23/3	---	6/1	6	31
23/4	---	6/2	7	32
24/1	6/3	---	8	33
24/2	6/4	---	9	34
24/3	---	6/3	8	33
24/4	---	6/4	9	34
25/1	7/1	---	2	27
25/2	7/2	---	3	28
25/3	---	7/1	2	27
25/4	---	7/2	3	28
26/1	7/3	---	4	29
26/2	7/4	---	5	30
26/3	---	7/3	4	29
26/4	---	7/4	5	30
27/1	8/1	---	1	26
27/2	8/2	---	10	35
27/3	---	8/1	1	26
27/4	---	8/2	10	35
28/1	8/3	---	11	36
28/2	8/4	---	12	37
28/3	---	8/3	11	36
28/4	---	8/4	12	37
31/1	15/1	---	1	26	J13/J10
31/2	15/2	---	10	35
31/3	---	15/1	1	26
31/4	---	15/2	10	35
32/1	15/3	---	11	36
32/2	15/4	---	12	37
32/3	---	15/3	11	36
32/4	---	15/4	12	37
33/1	16/1	---	2	27
33/2	16/2	---	3	28
33/3	---	16/1	2	27
33/4	---	16/2	3	28
34/1	16/3	---	4	29
34/2	16/4	---	5	30
34/3	---	16/3	4	29
34/4	---	16/4	5	30
35/1	17/1	---	6	31
35/2	17/2	---	7	32
35/3	---	17/1	6	31
35/4	---	17/2	7	32
36/1	17/3	---	8	33
36/2	17/4	---	9	34
36/3	---	17/3	8	33
36/4	---	17/4	9	34
37/1	18/1	---	22	47	J14/J8
37/2	18/2	---	23	48
37/3	---	18/1	22	47
37/4	---	18/2	23	48
38/1	18/3	---	24	49
38/2	18/4	---	25	50
38/3	---	18/3	24	49
38/4	---	18/4	25	50

Table B-4 maps the MC ports, the PSC ports, and the wire pairs when using the two-to-two cables (see Table 3-5) for a Direct Connect with a PSC configuration. The corresponding cable kit number is CAB-PSC-80-REPIN.

You can use the two-to-two cables to clearly associate the mapping between the wire pairs and the MC/PSC ports. These cables attach to the PSC MDF connections (J11 to J14) and the PSC POTS connections (J7 to J10) for systems using dual-port xTU-C modules.

Table B-4: Port Mapping for Two-to-Two Cables in a Direct Connect with PSC Configuration

MC Slot/Line	PSC Slot/Line	Champ Pins		Cable Connector
		Tip	Ring
1/1	1/1	1	26	P1
1/2	1/2	2	27
2/1	1/3	3	28
2/2	1/4	4	29
3/1	2/1	5	30
3/2	2/2	6	31
4/1	2/3	7	32
4/2	2/4	8	33
5/1	3/1	9	34
5/2	3/2	10	35
6/1	3/3	11	36
6/2	3/4	12	37
7/1	4/1	13	38
7/2	4/2	14	39
8/1	4/3	15	40
8/2	4/4	16	41
13/1	19/1	1	26	P2
13/2	19/2	2	27
14/1	19/3	3	28
14/2	19/4	4	29
15/1	20/1	5	30
15/2	20/2	6	31
16/1	20/3	7	32
16/2	20/4	8	33
17/1	21/1	9	34
17/2	21/2	10	35
18/1	21/3	11	36
18/2	21/4	12	37
19/1	22/1	13	38
19/2	22/2	14	39
20/1	22/3	15	40
20/2	22/4	16	41
21/1	5/1	1	26	P3
21/2	5/2	2	27
22/1	5/3	3	28
22/2	5/4	4	29
23/1	6/1	5	30
23/2	6/2	6	31
24/1	6/3	7	32
24/2	6/4	8	33
25/1	7/1	9	34
25/2	7/2	10	35
26/1	7/3	11	36
26/2	7/4	12	37
27/1	8/1	13	38
27/2	8/2	14	39
28/1	8/3	15	40
28/2	8/4	16	41
31/1	15/1	1	26	P4
31/2	15/2	2	27
32/1	15/3	3	28
32/2	15/4	4	29
33/1	16/1	5	30
33/2	16/2	6	31
34/1	16/3	7	32
34/2	16/4	8	33
35/1	17/1	9	34
35/2	17/2	10	35
36/1	17/3	11	36
36/2	17/4	12	37
37/1	18/1	13	38
37/2	18/2	14	39
38/1	18/3	15	40
38/2	18/4	16	41

B.2.2 Direct Connect without PSC Configuration Port Mapping Tables

Table B-5 maps the MC ports and the wire pairs when using the two-to-three cables (see Table 3-6) for a Direct Connect without a PSC configuration. The corresponding cable kit number is CAB-MC-3:2-REPIN. You can use the two-to-three cables to connect the MC to the MDF for systems using dual-port DMT-2 ATU-C modules.

Table B-5: Port Mapping for Two-to-Three Cables in a Direct Connect without PSC Configuration

MC Slot/Line	Champ Pins		Cable Connector/ Cable Part Number
	Tip	Ring
1/1	1	26	Connector P2/ Cable 72-1590-02
1/2	2	27
2/1	3	28
2/2	4	29
3/1	5	30
3/2	6	31
4/1	7	32
4/2	8	33
5/1	9	34
5/2	10	35
6/1	11	36
6/2	12	37
7/1	13	38
7/2	14	39
8/1	15	40
8/2	16	41
13/1	1	26	Connector P2/ Cable 72-1591-02
13/2	2	27
14/1	3	28
14/2	4	29
15/1	5	30
15/2	6	31
16/1	7	32
16/2	8	33
17/1	9	34
17/2	10	35
18/1	11	36
18/2	12	37
19/1	13	38
19/2	14	39
20/1	15	40
20/2	16	41
21/1	1	26	Connector P1/ Cable 72-1590-02
21/2	2	27
22/1	3	28
22/2	4	29
23/1	5	30
23/2	6	31
24/1	7	32
24/2	8	33
25/1	9	34
25/2	10	35
26/1	11	36
26/2	12	37
27/1	13	38
27/2	14	39
28/1	15	40
28/2	16	41
31/1	1	26	Connector P1/ Cable 72-1591-02
31/2	2	27
32/1	3	28
32/2	4	29
33/1	5	30
33/2	6	31
34/1	7	32
34/2	8	33
35/1	9	34
35/2	10	35
36/1	11	36
36/2	12	37
37/1	13	38
37/2	14	39
38/1	15	40
38/2	16	41

Table B-6 maps the MC ports and the wire pairs when using the three-to-three cables (see Table 3-7) for a Direct Connect without a PSC configuration. The corresponding cable kit number is CAB-MC128-MDF. You can use the three-to-three cables to connect the MC to the MDF for systems using dual-port DMT-2 ATU-C or quad-port xTU-C modules.

Table B-6: Port Mapping for Three-to-Three Cables in a Direct Connect without PSC Configuration

MC Slot/Line	Champ Pins		Cable Connector/ Cable Part Number
	Tip	Ring
1/1	1	26	Connector P4/ Cable 72-1765-01
1/2	2	27
1/3	3	28
1/4	4	29
2/1	5	30
2/2	6	31
2/3	7	32
2/4	8	33
3/1	9	34
3/2	10	35
3/3	11	36
3/4	12	37
4/1	13	38
4/2	14	39
4/3	15	40
4/4	16	41
5/1	17	42
5/2	18	43
5/3	19	44
5/4	20	45
6/1	21	46
6/2	22	47
6/3	23	48
6/4	24	49
7/1	1	26	Connector P5/ Cable 72-1765-01
7/2	2	27
7/3	3	28
7/4	4	29
8/1	5	30
8/2	6	31
8/3	7	32
8/4	8	33
13/1	1	26	Connector P1/ Cable 72-1720-01
13/2	2	27
13/3	3	28
13/4	4	29
14/1	5	30
14/2	6	31
14/3	7	32
14/4	8	33
15/1	9	34
15/2	10	35
15/3	11	36
15/4	12	37
16/1	13	38
16/2	14	39
16/3	15	40
16/4	16	41
17/1	17	42
17/2	18	43
17/3	19	44
17/4	20	45
18/1	21	46
18/2	22	47
18/3	23	48
18/4	24	49
19/1	1	26	Connector P2/ Cable 72-1720-01
19/2	2	27
19/3	3	28
19/4	4	29
20/1	5	30
20/2	6	31
20/3	7	32
20/4	8	33
21/1	9	34	Connector P5/ Cable 72-1765-01
21/2	10	35
21/3	11	36
21/4	12	37
22/1	13	38
22/2	14	39
22/3	15	40
22/4	16	41
23/1	17	42
23/2	18	43
23/3	19	44
23/4	20	45
24/1	21	46
24/2	22	47
24/3	23	48
24/4	24	49
25/1	1	26	Connector P6/ Cable 72-1765-01
25/2	2	27
25/3	3	28
25/4	4	29
26/1	5	30
26/2	6	31
26/3	7	32
26/4	8	33
27/1	9	34
27/2	10	35
27/3	11	36
27/4	12	37
28/1	13	38
28/2	14	39
28/3	15	40
28/4	16	41
31/1	9	34	Connector P2/ Cable 72-1720-01
31/2	10	35
31/3	11	36
31/4	12	37
32/1	13	38
32/2	14	39
32/3	15	40
32/4	16	41
33/1	17	42
33/2	18	43
33/3	19	44
33/4	20	45
34/1	21	46
34/2	22	47
34/3	23	48
34/4	24	49
35/1	1	26	Connector P3/ Cable 72-1720-01
35/2	2	27
35/3	3	28
35/4	4	29
36/1	5	30
36/2	6	31
36/3	7	32
36/4	8	33
37/1	9	34
37/2	10	35
37/3	11	36
37/4	12	37
38/1	13	38
38/2	14	39
38/3	15	40
38/4	16	41

Table B-7 maps the MC ports and the wire pairs when using the five-to-six cables (see Table 3-8) for a Direct Connect without a PSC configuration. The corresponding cable kit number is CAB-MC-6:5-REPIN. You can use the five-to-six cables to connect the MC to the MDF for systems using dual-port DMT-2 ATU-C or quad-port xTU-C modules.

Table B-7: Port Mapping for Five-to-Six Cables in a Direct Connect without PSC Configuration

MC Slot/Line	Champ Pins		Cable Connector
	Tip	Ring
1/1	1	26	P1
1/2	2	27
1/3	3	28
1/4	4	29
2/1	5	30
2/2	6	31
2/3	7	32
2/4	8	33
3/1	9	34
3/2	10	35
3/3	11	36
3/4	12	37
4/1	13	38
4/2	14	39
4/3	15	40
4/4	16	41
5/1	17	42
5/2	18	43
5/3	19	44
5/4	20	45
6/1	21	46
6/2	22	47
6/3	23	48
6/4	24	49
7/1	1	26	P2
7/2	2	27
7/3	3	28
7/4	4	29
8/1	5	30
8/2	6	31
8/3	7	32
8/4	8	33
13/1	9	34
13/2	10	35
13/3	11	36
13/4	12	37
14/1	13	38
14/2	14	39
14/3	15	40
14/4	16	41
15/1	17	42
15/2	18	43
15/3	19	44
15/4	20	45
16/1	21	46
16/2	22	47
16/3	23	48
16/4	24	49
17/1	1	26	P3
17/2	2	27
17/3	3	28
17/4	4	29
18/1	5	30
18/2	6	31
18/3	7	32
18/4	8	33
19/1	9	34
19/2	10	35
19/3	11	36
19/4	12	37
21/1	13	38
21/2	14	39
21/3	15	40
21/4	16	41
22/1	17	42
22/2	18	43
22/3	19	44
22/4	20	45
23/1	21	46
23/2	22	47
23/3	23	48
23/4	24	49
24/1	1	26	P4
24/2	2	27
24/3	3	28
24/4	4	29
25/1	5	30
25/2	6	31
25/3	7	32
25/4	8	33
26/1	9	34
26/2	10	35
26/3	11	36
26/4	12	37
27/1	13	38
27/2	14	39
27/3	15	40
27/4	16	41
28/1	17	42
28/2	18	43
28/3	19	44
28/4	20	45
31/1	21	46
31/2	22	47
31/3	23	48
31/4	24	49
32/1	1	26	P5
32/2	2	27
32/3	3	28
32/4	4	29
33/1	5	30
33/2	6	31
33/3	7	32
33/4	8	33
34/1	9	34
34/2	10	35
34/3	11	36
34/4	12	37
35/1	13	38
35/2	14	39
35/3	15	40
35/4	16	41
36/1	17	42
36/2	18	43
36/3	19	44
36/4	20	45
37/1	21	46
37/2	22	47
37/3	23	48
37/4	24	49

B.2.3 Siecor POTS Splitter Port Mapping Table

Table B-8 maps the MC ports, the POTS splitter ports, and the wire pairs when using the one-to-one cables (see Table 3-9) when a Siecor POTS splitter is installed in your configuration. The corresponding cable kit number is CAB-6121-1.

Table B-8: Port Mapping for One-to-One Cables with a Siecor POTS Splitter

MC Slot/Line	POTS Splitter Slot/Line	Champ Pins		POTS Splitter Connection
		Tip	Ring
1/1	1/1	26	1	Line 1 to 24 or POTS 1 to 24
1/2	1/2	27	2
1/3	1/3	28	3
1/4	1/4	29	4
2/1	1/5	30	5
2/2	1/6	31	6
2/3	1/7	32	7
2/4	1/8	33	8
3/1	2/1	34	9
3/2	2/2	35	10
3/3	2/3	36	11
3/4	2/4	37	12
4/1	2/5	38	13
4/2	2/6	39	14
4/3	2/7	40	15
4/4	2/8	41	16
5/1	3/1	42	17
5/2	3/2	43	18
5/3	3/3	44	19
5/4	3/4	45	20
6/1	3/5	46	21
6/2	3/6	47	22
6/3	3/7	48	23
6/4	3/8	49	24
7/1	4/1	26	1	Line 25 to 48 or POTS 25 to 48
7/2	4/2	27	2
7/3	4/3	28	3
7/4	4/4	29	4
8/1	4/5	30	5
8/2	4/6	31	6
8/3	4/7	32	7
8/4	4/8	33	8
13/1	5/1	34	9
13/2	5/2	35	10
13/3	5/3	36	11
13/4	5/4	37	12
14/1	5/5	38	13
14/2	5/6	39	14
14/3	5/7	40	15
14/4	5/8	41	16
15/1	6/1	42	17
15/2	6/2	43	18
15/3	6/3	44	19
15/4	6/4	45	20
16/1	6/5	46	21
16/2	6/6	47	22
16/3	6/7	48	23
16/4	6/8	49	24
17/1	7/1	26	1	Line 49 to 72 or POTS 49 to 72
17/2	7/2	27	2
17/3	7/3	28	3
17/4	7/4	29	4
18/1	7/5	30	5
18/2	7/6	31	6
18/3	7/7	32	7
18/4	7/8	33	8
19/1	8/1	34	9
19/2	8/2	35	10
19/3	8/3	36	11
19/4	8/4	37	12
20/1	8/5	38	13
20/2	8/6	39	14
20/3	8/7	40	15
20/4	8/8	41	16
21/1	9/1	42	17
21/2	9/2	43	18
21/3	9/3	44	19
21/4	9/4	45	20
22/1	9/5	46	21
22/2	9/6	47	22
22/3	9/7	48	23
22/4	9/8	49	24
23/1	10/1	26	1	Line 73 to 96 or POTS 73 to 96
23/2	10/2	27	2
23/3	10/3	28	3
23/4	10/4	29	4
24/1	10/5	30	5
24/2	10/6	31	6
24/3	10/7	32	7
24/4	10/8	33	8
25/1	11/1	34	9
25/2	11/2	35	10
25/3	11/3	36	11
25/4	11/4	37	12
26/1	11/5	38	13
26/2	11/6	39	14
26/3	11/7	40	15
26/4	11/8	41	16
27/1	12/1	42	17
27/2	12/2	43	18
27/3	12/3	44	19
27/4	12/4	45	20
28/1	12/5	46	21
28/2	12/6	47	22
28/3	12/7	48	23
28/4	12/8	49	24
31/1	13/1	26	1	Line 97 to 120 or POTS 97 to 120
31/2	13/2	27	2
31/3	13/3	28	3
31/4	13/4	29	4
32/1	13/5	30	5
32/2	13/6	31	6
32/3	13/7	32	7
32/4	13/8	33	8
33/1	14/1	34	9
33/2	14/2	35	10
33/3	14/3	36	11
33/4	14/4	37	12
34/1	14/5	38	13
34/2	14/6	39	14
34/3	14/7	40	15
34/4	14/8	41	16
35/1	15/1	42	17
35/2	15/2	43	18
35/3	15/3	44	19
35/4	15/4	45	20
36/1	15/5	46	21
36/2	15/6	47	22
36/3	15/7	48	23
36/4	15/8	49	24
37/1	16/1	26	1	Line 121 to 128 or POTS 121 to 128
37/2	16/2	27	2
37/3	16/3	28	3
37/4	16/4	29	4
38/1	16/5	30	5
38/2	16/6	31	6
38/3	16/7	32	7
38/4	16/8	33	8

B.2.4 Port Mapping Table for Building MC Cables

Table B-9 provides the Champ pins and MC port mapping information needed to build your own MC cables.

Table B-9: Port Mapping for Building MC Cables

Connector	Champ Pins		MC Slot/Line
	Tip	Ring
J39 xDSL Slots 3 through 8 (pins 25 and 50 are not used)	1	2	6/1
	3	4	6/2
	5	6	6/3
	7	8	6/4
	9	10	7/1
	11	12	7/2
	13	14	7/3
	15	16	7/4
	17	18	8/1
	19	20	8/2
	21	22	8/3
	23	24	8/4
	26	27	5/1
	28	29	5/2
	30	31	5/3
	32	33	5/4
	34	35	4/1
	36	37	4/2
	38	39	4/3
	40	41	4/4
	42	43	3/1
	44	45	3/2
	46	47	3/3
	48	49	3/4
J40 xDSL Slots 1, 2, 21, and 22 (pins 9 through 25 are not used)	1	2	22/1
	3	4	22/2
	5	6	22/3
	7	8	22/4
	26	27	21/1
	28	29	21/2
	30	31	21/3
	32	33	21/4
	34	35	2/1
	36	37	2/2
	38	39	2/3
	40	41	2/4
	42	43	1/1
	44	45	1/2
	46	47	1/3
	48	49	1/4
J41 xDSL Slots 23 through 23 (pins 25 and 50 are not used)	1	2	26/1
	3	4	26/2
	5	6	26/3
	7	8	26/4
	9	10	27/1
	11	12	27/2
	13	14	27/3
	15	16	27/4
	17	18	28/1
	19	20	28/2
	21	22	28/3
	23	24	28/4
	26	27	25/1
	28	29	25/2
	30	31	25/3
	32	33	25/4
	34	35	24/1
	36	37	24/2
	38	39	24/3
	40	41	24/4
	42	43	23/1
	44	45	23/2
	46	47	23/3
	48	49	23/4
J42 xDSL Slots 13 through 18 (pins 25 and 50 are not used)	1	2	17/1
	3	4	17/2
	5	6	17/3
	7	8	17/4
	9	10	18/1
	11	12	18/2
	13	14	18/3
	15	16	18/4
	17	18	13/1
	19	20	13/2
	21	22	13/3
	23	24	13/4
	26	27	16/1
	28	29	16/2
	30	31	16/3
	32	33	16/4
	34	35	15/1
	36	37	15/2
	38	39	15/3
	40	41	15/4
	42	43	14/1
	44	45	14/2
	46	47	14/3
	48	49	14/4
J43 xDSL Slots 19, 20, 37, and 38 (pins 9 through 25 and 50 are not used)	1	2	20/1
	3	4	20/2
	5	6	20/3
	7	8	20/4
	26	27	19/1
	28	29	19/2
	30	31	19/3
	32	33	19/4
	34	35	38/1
	36	37	38/2
	38	39	38/3
	40	41	38/4
	42	43	37/1
	44	45	37/2
	46	47	37/3
	48	49	37/4
J44 xDSL Slots 31 through 36 (pins 25 and 50 are not used)	1	2	35/1
	3	4	35/2
	5	6	35/3
	7	8	35/4
	9	10	36/1
	11	12	36/2
	13	14	36/3
	15	16	36/4
	17	18	31/1
	19	20	31/2
	21	22	31/3
	23	24	31/4
	26	27	34/1
	28	29	34/2
	30	31	34/3
	32	33	34/4
	34	35	33/1
	36	37	33/2
	38	39	33/3
	40	41	33/4
	42	43	32/1
	44	45	32/2
	46	47	32/3
	48	49	32/4

B.3 Standard Telco Color Chart

In designing the cables for the Cisco 6100 Series connections, Cisco used a standard telco color chart. Table B-10 lists the colors used for the Cisco 6100 Series cables.

Table B-10: Standard Telco Color Chart

Wire Color	P1	Wire Color	P2		Wire Color	P1	Wire Color	P2
Wht/blu	1	Wht/blu	1		Grn/blk	38	Grn/blk	38
Blu/wht	26	Blu/wht	26		Blk/brn	14	Blk/brn	14
Wht/org	2	Wht/org	2		Brn/blk	39	Brn/blk	39
Org/wht	27	Org/wht	27		Blk/gry	15	Blk/gry	15
Wht/grn	3	Wht/grn	3		Gry/blk	40	Gry/blk	40
Grn/wht	28	Grn/wht	28		Yel/blu	16	Yel/blu	16
Wht/brn	4	Wht/brn	4		Blu/yel	41	Blu/yel	41
Brn/wht	29	Brn/wht	29		Yel/org	17	Yel/org	17
Wht/gry	5	Wht/gry	5		Org/yel	42	Org/yel	42
Gry/wht	30	Gry/wht	30		Yel/grn	18	Yel/grn	18
Red/blu	6	Red/blu	6		Grn/yel	43	Grn/yel	43
Blu/red	31	Blu/red	31		Yel/brn	19	Yel/brn	19
Red/org	7	Red/org	7		Brn/yel	44	Brn/yel	44
Org/red	32	Org/red	32		Yel/gry	20	Yel/gry	20
Red/grn	8	Red/grn	8		Gry/yel	45	Gry/yel	45
Grn/red	33	Grn/red	33		Vio/blu	21	Vio/blu	21
Red/brn	9	Red/brn	9		Blu/vio	46	Blu/vio	46
Brn/red	34	Brn/red	34		Vio/org	22	Vio/org	22
Red/gry	10	Red/gry	10		Org/vio	47	Org/vio	47
Gry/red	35	Gry/red	35		Vio/grn	23	Vio/grn	23
Blk/blu	11	Blk/blu	11		Grn/vio	48	Grn/vio	48
Blu/blk	36	Blu/blk	36		Vio/brn	24	Vio/brn	24
Blk/org	12	Blk/org	12		Brn/vio	49	Brn/vio	49
Org/blk	37	Org/blk	37		Vio/gry	25	Vio/gry	25
Blk/grn	13	Blk/grn	13		Gry/vio	50	Gry/vio	50