cc/td/doc/product/dsl_prod/c6100/userdoc/rel220
hometocprevnextglossaryfeedbacksearchhelp
PDF

Table of Contents

Cables and Connector Pinouts

Cables and Connector Pinouts

This appendix provides pictures of the cables, their function in the Cisco 6100 system, and their corresponding connector pinouts. Part numbers for Digital Off-Hook (DOH) standard and direct connect configuration cables (and other 6100 system components) are listed in the "NetSpeed/Cisco Part Number Conversion" appendix.

A.1 Multiplexer Cables and Connectors

A.1.1 LCC Cables

There are three line concentration chassis (LCC) cables used to connect the LCC to the ATU-C pools in the multiplexer chassis (MC). These cables are specially built by Cisco. The LCC connector on the cables is shown in the following illustration. Refer to the "NetSpeed/Cisco Part Number Conversion" appendix for a listing of DOH standard configuration cables and their respective Cisco part numbers.


Figure A-1: LCC Cable Connector


A.1.2 POTS Splitter Chassis Cables

POTS cables are used to connect the MC to the POTS splitter chassis (PSC). They are only used when there are no LCCs in the 6100. The following figures show the POTS connector, pinout locations, and tip/ring cable layout for the MC. lists the POTS cables and part numbers. Refer to the "NetSpeed/Cisco Part Number Conversion" appendix for a listing of DOH standard and direct connect configuration cables and their respective Cisco part numbers.


Figure A-2: PSC Cable Connector



Figure A-3: Connector Pin Locations for All PSC Connectors



Figure A-4: Tip/Ring Cable Pair Layout for the Multiplexer Chassis



Table A-1: CHAMP Connector Pinouts to POTS Splitter Chassis
Connector Pin Slot Line Tip/Ring Pin Slot Line Tip/Ring

J39

1

6

1

Tip

26

5

1

Ring

ADSL Slots 3-8

2

6

1

Ring

27

5

1

Tip

3

6

2

Tip

28

5

2

Ring

4

6

2

Ring

29

5

2

Tip

5

6

3

Tip

30

5

3

Ring

6

6

3

Ring

31

5

3

Tip

7

6

4

Tip

32

5

4

Ring

8

6

4

Ring

33

5

4

Tip

9

7

1

Tip

34

4

1

Ring

10

7

1

Ring

35

4

1

Tip

11

7

2

Tip

36

4

2

Ring

12

7

2

Ring

37

4

2

Tip

13

7

3

Tip

38

4

3

Ring

14

7

3

Ring

39

4

3

Tip

15

7

4

Tip

40

4

4

Ring

16

7

4

Ring

41

4

4

Tip

17

8

1

Tip

42

3

1

Ring

18

8

1

Ring

43

3

1

Tip

19

8

2

Tip

44

3

2

Ring

Pins 25 and 50 are not used

20

8

2

Ring

45

3

2

Tip

21

8

3

Tip

46

3

3

Ring

22

8

3

Ring

47

3

3

Tip

23

8

4

Tip

48

3

4

Ring

24

8

4

Ring

49

3

4

Tip

25

50

J40

1

22

1

Tip

26

21

1

Ring

ADSL Slots 1, 2, 21, 22

2

22

1

Ring

27

21

1

Tip

3

22

2

Tip

28

21

2

Ring

4

22

2

Ring

29

21

2

Tip

5

22

3

Tip

30

21

3

Ring

6

22

3

Ring

31

21

3

Tip

Pins 9-25 and 50 are not

7

22

4

Tip

32

21

4

Ring

used

8

22

4

Ring

33

21

4

Tip

9

34

2

1

Ring

10

35

2

1

Tip

11

36

2

2

Ring

12

37

2

2

Tip

13

38

2

3

Ring

14

39

2

3

Tip

15

40

2

4

Ring

16

41

2

4

Tip

17

42

1

1

Ring

18

43

1

1

Tip

19

44

1

2

Ring

20

45

1

2

Tip

21

46

1

3

Ring

22

47

1

3

Tip

23

48

1

4

Ring

24

49

1

4

Tip

25

50

J41

1

26

1

Tip

26

25

1

Ring

ADSL Slots 23-28

2

26

1

Ring

27

25

1

Tip

3

26

2

Tip

28

25

2

Ring

4

26

2

Ring

29

25

2

Tip

5

26

3

Tip

30

25

3

Ring

6

26

3

Ring

31

25

3

Tip

7

26

4

Tip

32

25

4

Ring

8

26

4

Ring

33

25

4

Tip

9

27

1

Tip

34

24

1

Ring

10

27

1

Ring

35

24

1

Tip

11

27

2

Tip

36

24

2

Ring

12

27

2

Ring

37

24

2

Tip

13

27

3

Tip

38

24

3

Ring

14

27

3

Ring

39

24

3

Tip

15

27

4

Tip

40

24

4

Ring

16

27

4

Ring

41

24

4

Tip

17

28

1

Tip

42

24

1

Ring

18

28

1

Ring

43

23

1

Tip

19

28

2

Tip

44

23

2

Ring

Pins 25 and 50 are not used

20

28

2

Ring

45

23

2

Tip

21

28

3

Tip

46

23

3

Ring

22

28

3

Ring

47

23

3

Tip

23

28

4

Tip

48

23

4

Ring

24

28

4

Ring

49

23

4

Tip

25

50

J42

1

17

1

Tip

26

16

1

Ring

ADSL Slots 13-18

2

17

1

Ring

27

16

1

Tip

3

17

2

Tip

28

16

2

Ring

4

17

2

Ring

29

16

2

Tip

5

17

3

Tip

30

16

3

Ring

6

17

3

Ring

31

16

3

Tip

7

17

4

Tip

32

16

4

Ring

8

17

4

Ring

33

16

4

Tip

9

18

1

Tip

34

15

1

Ring

10

18

1

Ring

35

15

1

Tip

11

18

2

Tip

36

15

2

Ring

12

18

2

Ring

37

15

2

Tip

13

18

3

Tip

38

15

3

Ring

14

18

3

Ring

39

15

3

Tip

15

18

4

Tip

40

15

4

Ring

16

18

4

Ring

41

15

4

Tip

17

13

1

Tip

42

14

1

Ring

18

13

1

Ring

43

14

1

Tip

19

13

2

Tip

44

14

2

Ring

Pins 25 and 50 are not used

20

13

2

Ring

45

14

2

Tip

21

13

3

Tip

46

14

3

Ring

22

13

3

Ring

47

14

3

Tip

23

13

4

Tip

48

14

4

Ring

24

13

4

Ring

49

14

4

Tip

25

50

J43

1

20

1

Tip

26

19

1

Ring

ADSL Slots 19, 20, 37, 38

2

20

1

Ring

27

19

1

Tip

3

20

2

Tip

28

19

2

Ring

4

20

2

Ring

29

19

2

Tip

5

20

3

Tip

30

19

3

Ring

6

20

3

Ring

31

19

3

Tip

7

20

4

Tip

32

19

4

Ring

8

20

4

Ring

33

19

4

Tip

9

34

38

1

Ring

10

35

38

1

Tip

11

36

38

2

Ring

12

37

38

2

Tip

13

38

38

3

Ring

14

39

38

3

Tip

15

40

38

4

Ring

16

41

38

4

Tip

17

42

37

1

Ring

18

43

37

1

Tip

19

44

37

2

Ring

Pins 9-25 and 50 are not

20

45

37

2

Tip

used

21

46

37

3

Ring

22

47

37

3

Tip

23

48

37

4

Ring

24

49

37

4

Tip

25

50

37

J44

1

20

1

Tip

26

19

1

Ring

ADSL Slots 31-36

2

20

1

Ring

27

19

1

Tip

3

20

2

Tip

28

19

2

Ring

4

20

2

Ring

29

19

2

Tip

5

20

3

Tip

30

19

3

Ring

6

20

3

Ring

31

19

3

Tip

7

20

4

Tip

32

19

4

Ring

8

20

4

Ring

33

19

4

Tip

9

34

38

1

Ring

10

35

38

1

Tip

11

36

38

2

Ring

12

37

38

2

Tip

13

38

38

3

Ring

14

39

38

3

Tip

15

40

38

4

Ring

16

41

38

4

Tip

17

42

37

1

Ring

18

43

37

1

Tip

19

44

37

2

Ring

Pins 25 and 50 are not used

20

45

37

2

Tip

21

46

37

3

Ring

22

47

37

3

Tip

23

48

37

4

Ring

24

49

37

4

Tip

25

50

37

A.1.3 System Management Bus

The 26-pin SCSI cable is used to route the system management bus between the multiplexer chassis (MC) and the LCC. If your system does not include an LCC, this connection will not be used. See the "Connecting the LCC Controller to the MC" section for more information.


Figure A-5: 26-pin SCSI Cable Connector (J47)


Refer to the "NetSpeed/Cisco Part Number Conversion" appendix for a listing of DOH standard and direct connect configuration cables and their respective NetSpeed part numbers.


Table A-2: System Management Bus (J47) Connector Pinouts
Pin Signal Pin Signal Pin Signal

1
2
3
4
5
6
7
8
9
10

SEC_SC_ACT_LCC_N
SEC_SYS_RST_N
PRI_SC_ACT_LCC_N
PRI_SYS_RST_N
SMB_SPARE4
SMB_SPARE3
SMB_SPARE2
DGND
DGND
DGND

11
12
13
14
15
16
17
18
19
20

+5VD
+5VD
+5VD
SMB_SEC-
SMB_SEC+
SMB_SPARE1
SMB_SPARE0
28N655
28N655
19RTN

21
22
23
24
25
26

19RTN
19RTN
28N653
28N653
SMB_PRI-
SMB_PRI+

A.1.4 Power Terminal Block

The power terminal block is used to connect the multiplexer to the power source on the fuse and alarm panel. See the "Connecting Power from the MC and LCC to the Fuse/Alarm Panel" section for more information on fusing.


Figure A-6: Power Terminal Block


A.1.5 Multiplexer Chassis Ground Jumper

The chassis ground jumper is optional depending on site requirements. Chassis ground may be connected to logic ground, or -48RTN may be connected to chassis ground. Normally, no ground jumpering is necessary. The following illustration shows the chassis ground jumper. See the "Grounding the MC and LCCs" section for more information on grounding.


Figure A-7: Chassis Ground Jumper


A.1.6 Alarm Contacts

The Cisco 6100 provides alarm contacts for audible, visual, and E2A alarm connections. These connections support minor, major, and critical alarm reporting. The connectors and their associated pinouts are shown in the following illustration. See the "Connecting the Alarm Contacts" section for more information on the alarm interface.


Figure A-8: Alarm Contacts



Table A-3: Alarm Contact Pinouts
Connector Pin Signal

E2A

1

Critical_E2+

2

Critical_E2-

P14

3

Major_E2+

4

Major_E2-

5

Minor_E2+

6

Minor_E2-

7

Fan Alarm+

8

Fan Alarm-

Visual

1

Critical_V+

2

Critical_V-

P15

3

Major_V+

4

Major_V-

5

Minor_V+

6

Minor_V-

7

ACO_IN_V (future)

8

ACO_RTN_V (future)

Audible

1

Critical_A+

2

Critical_A-

P17

3

Major_A+

4

Major_A-

5

Minor_A+

6

Minor_A-

7

ACO_IN_A

8

ACO_RTN_A
Note The Fan Alarm+ (pin 7) and Fan Alarm- (pin 8) are reserved for future use.

A.2 LCC Connectors

The LCC connectors for reference during system setup/operation are discussed in this section.

Note This section applies to the DOH standard configuration only.

A.2.1 LCC CHAMP Connectors

The rear panel of the LCC provides four CHAMP connectors to transfer data between the LCC and the PSC. Pin locations are the same for all CHAMP connectors on the LCC and are shown in the following illustration. Connector pinouts for each connector are listed in the tables that follow the illustration.


Figure A-9: Connector Pin Locations for All LCC Connectors



Table A-4: LCC CHAMP Connectors for Data Transfer to POTS
Connector Pin Slot Line Tip/Ring Pin Slot Line Tip/Ring

J21

1

4

1

Tip

26

3

1

Ring

Slots 1-4

2

4

1

Ring

27

3

1

Tip

3

4

2

Tip

28

3

2

Ring

4

4

2

Ring

29

3

2

Tip

5

4

3

Tip

30

3

3

Ring

6

4

3

Ring

31

3

3

Tip

7

4

4

Tip

32

3

4

Ring

8

4

4

Ring

33

3

4

Tip

9

Tip

34

2

1

Ring

10

Ring

35

2

1

Tip

11

Tip

36

2

2

Ring

12

Ring

37

2

2

Tip

13

Tip

38

2

3

Ring

14

Ring

39

2

3

Tip

15

Tip

40

2

4

Ring

16

Ring

41

2

4

Tip

17

Tip

42

1

1

Ring

18

Ring

43

1

1

Tip

19

Tip

44

1

2

Ring

Pins 9-25 and 50 are not

20

Ring

45

1

2

Tip

used

21

Tip

46

1

3

Ring

22

Ring

47

1

3

Tip

23

Tip

48

1

4

Ring

24

Ring

49

1

4

Tip

25

50

J22

1

8

1

Tip

26

7

1

Ring

Slots 5-10

2

8

1

Ring

27

7

1

Tip

3

8

2

Tip

28

7

2

Ring

4

8

2

Ring

29

7

2

Tip

5

8

3

Tip

30

7

3

Ring

6

8

3

Ring

31

7

3

Tip

7

8

4

Tip

32

7

4

Ring

8

8

4

Ring

33

7

4

Tip

9

9

1

Tip

34

6

1

Ring

10

9

1

Ring

35

6

1

Tip

11

9

2

Tip

36

6

2

Ring

12

9

2

Ring

37

6

2

Tip

13

9

3

Tip

38

6

3

Ring

14

9

3

Ring

39

6

3

Tip

15

9

4

Tip

40

6

4

Ring

16

9

4

Ring

41

6

4

Tip

17

10

1

Tip

42

5

1

Ring

18

10

1

Ring

43

5

1

Tip

19

10

2

Tip

44

5

2

Ring

20

10

2

Ring

45

5

2

Tip

21

10

3

Tip

46

5

3

Ring

Pins 25 and 50 are not used

22

10

3

Ring

47

5

3

Tip

23

10

4

Tip

48

5

4

Ring

24

10

4

Ring

49

5

4

Tip

25

50

J23

1

17

1

Tip

26

16

1

Ring

Slots 13-18

2

17

1

Ring

27

16

1

Tip

3

17

2

Tip

28

16

2

Ring

4

17

2

Ring

29

16

2

Tip

5

17

3

Tip

30

16

3

Ring

6

17

3

Ring

31

16

3

Tip

7

17

4

Tip

32

16

4

Ring

8

17

4

Ring

33

16

4

Tip

9

18

1

Tip

34

15

1

Ring

10

18

1

Ring

35

15

1

Tip

11

18

2

Tip

36

15

2

Ring

12

18

2

Ring

37

15

2

Tip

13

18

3

Tip

38

15

3

Ring

14

18

3

Ring

39

15

3

Tip

15

18

4

Tip

40

15

4

Ring

16

18

4

Ring

41

15

4

Tip

17

13

1

Tip

42

14

1

Ring

18

13

1

Ring

43

14

1

Tip

19

13

2

Tip

44

14

2

Ring

Pins 25 and 50 are not used

20

13

2

Ring

45

14

2

Tip

21

13

3

Tip

46

14

3

Ring

22

13

3

Ring

47

14

3

Tip

23

13

4

Tip

48

14

4

Ring

24

13

4

Ring

49

14

4

Tip

25

50

J24

1

22

1

Tip

26

21

1

Ring

Slots 19-22

2

22

1

Ring

27

21

1

Tip

3

22

2

Tip

28

21

2

Ring

4

22

2

Ring

29

21

2

Tip

5

22

3

Tip

30

21

3

Ring

6

22

3

Ring

31

21

3

Tip

7

22

4

Tip

32

21

4

Ring

8

22

4

Ring

33

21

4

Tip

9

Tip

34

20

1

Ring

10

Ring

35

20

1

Tip

11

Tip

36

20

2

Ring

12

Ring

37

20

2

Tip

13

Tip

38

20

3

Ring

14

Ring

39

20

3

Tip

15

Tip

40

20

4

Ring

16

Ring

41

20

4

Tip

17

Tip

42

19

1

Ring

18

Ring

43

19

1

Tip

19

Tip

44

19

2

Ring

Pins 9-25 and 50 are not

20

Ring

45

19

2

Tip

used

21

Tip

46

19

3

Ring

22

Ring

47

19

3

Tip

23

Tip

48

19

4

Ring

24

Ring

49

19

4

Tip

25

50

25

50

37

See the "Connecting the LCC to the PSC" section for more information on this connector.

A.2.2 LCC System Management Bus Connector

The LCC system management bus connector receives management information from the multiplexer and then daisy chains that information from LCC to LCC. The locations of the pins on the 9-pin D-sub connectors are shown in the following illustration. The connector pinouts for each connector are listed in the tables that follow the illustration. See the "Connecting the LCC Controller to the MC" section for more information.


Figure A-10: LCC Management 26-pin SCSI Cable Connector (J29 and J30)



Table A-5: System Management Bus (J29, J30, J31) Connector Pinouts
Pin Signal Pin Signal Pin Signal

1
2
3
4
5
6
7
8
9
10

SEC_SC_ACT_LCC_N
SEC_SYS_RST_N
PRI_SC_ACT_LCC_N
PRI_SYS_RST_N
SMB_SPARE4
SMB_SPARE3
SMB_SPARE2
DGND
DGND
DGND

11
12
13
14
15
16
17
18
19
20

+5VD
+5VD
+5VD
SMB_SEC-
SMB_SEC+
SMB_SPARE1
SMB_SPARE0
28N655
28N655
19RTN

21
22
23
24
25
26

19RTN
19RTN
28N653
28N653
SMB_PRI-
SMB_PRI+

1
2
3
4
5
6
7
8
9
10

SEC_SC_ACT_LCC_N
SEC_SYS_RST_N
PRI_SC_ACT_LCC_N
PRI_SYS_RST_N
SMB_SPARE4
SMB_SPARE3
SMB_SPARE2
DGND
DGND
DGND

11
12
13
14
15
16
17
18
19
20

+5VD
+5VD
+5VD
SMB_SEC-
SMB_SEC+
SMB_SPARE1
SMB_SPARE0
28N655
28N655
19RTN

21
22
23
24
25
26

19RTN
19RTN
28N653
28N653
SMB_PRI-
SMB_PRI+

See the "Connecting the LCC Controller to the MC" section section.

A.2.3 LCC Power Connections

The power connection on the LCC rear panel is a 4-position terminal block. The illustration that follows shows the connector and the assignments for the 4 positions. See the "Connecting Power from the MC and LCC to the Fuse/Alarm Panel" section for more information on fusing.


Figure A-11: LCC Power Connection


A.2.4 LCC Chassis Ground/Logic Ground Jumper

The grounding jumper on the LCC allows you to ground the LCC in one of two ways:

An illustration of this jumper is shown in the following illustration. See the "Grounding the MC and LCCs" section for more information on grounding.

Note Normally, no logic to chassis grounding is necessary.

Figure A-12: LCC Grounding Jumper


A.3 POTS Splitter Chassis Connectors

The rear panel of the PSC provides CHAMP connectors to the subscriber line for connection to the Telco PSTN, and supports the ADSL signals. The ADSL signals either go to the multiplexer if there is not an LCC, or to the LCC when present. Pin locations are the same for all CHAMP connectors on the POTS chassis and are shown in the following illustration. Connector pinouts are shown for each set of cables (line, voice, or ADSL) in the tables that follow.

Note This section applies to both DOH standard and direct connect configurations.

Figure A-13: Connector Pin Locations for All CHAMP Connectors



Figure A-14: Tip/Ring Cable Pair Layout Between the PSC and MDF


Note  Connectors J7-J10 are for POTS going out to the MDF, and J11-J14 are for ADSL lines coming into the PSC from the MDF.

Table A-6: PSC CHAMP Connector Pinouts to POTS Connections
Connector Pin Slot Line Tip/Ring Pin Slot Line Tip/Ring

J7

1

3

1

Tip

26

3

1

Ring

Slots 1-5

2

3

2

Tip

27

3

2

Ring

3

3

3

Tip

28

3

3

Ring

4

3

4

Tip

29

3

4

Ring

5

2

1

Tip

30

2

1

Ring

6

2

2

Tip

31

2

2

Ring

7

2

3

Tip

32

2

3

Ring

8

2

4

Tip

33

2

4

Ring

9

1

1

Tip

34

1

1

Ring

10

1

2

Tip

35

1

2

Ring

11

1

3

Tip

36

1

3

Ring

12

1

4

Tip

37

1

4

Ring

Pins 13-17 and 38-42 are

13

38

not used

14

39

15

40

16

41

17

42

18

4

1

Tip

43

4

1

Ring

19

4

2

Tip

44

4

2

Ring

20

4

3

Tip

45

4

3

Ring

21

4

4

Tip

46

4

4

Ring

22

5

1

Tip

47

5

1

Ring

23

5

2

Tip

48

5

2

Ring

24

5

3

Tip

49

5

3

Ring

25

5

4

Tip

50

5

4

Ring

J8

1

20

1

Tip

26

20

1

Ring

Slots 18-22

2

20

2

Tip

27

20

2

Ring

3

20

3

Tip

28

20

3

Ring

4

20

4

Tip

29

20

4

Ring

5

21

1

Tip

30

21

1

Ring

6

21

2

Tip

31

21

2

Ring

Pins 13-17 and 38-42 are

7

21

3

Tip

32

21

3

Ring

not used

8

21

4

Tip

33

21

4

Ring

9

22

1

Tip

34

22

1

Ring

10

22

2

Tip

35

22

2

Ring

11

22

3

Tip

36

22

3

Ring

12

22

4

Tip

37

22

4

Ring

13

38

14

39

15

40

16

41

17

42

18

19

1

Tip

43

19

1

Ring

19

19

2

Tip

44

19

2

Ring

20

19

3

Tip

45

19

3

Ring

21

19

4

Tip

46

19

4

Ring

22

18

1

Tip

47

18

1

Ring

23

18

2

Tip

48

18

2

Ring

24

18

3

Tip

49

18

3

Ring

25

18

4

Tip

50

18

4

Ring

J9

1

8

1

Tip

26

8

1

Ring

Slots 6-10

2

7

1

Tip

27

7

1

Ring

3

7

2

Tip

28

7

2

Ring

4

7

3

Tip

29

7

3

Ring

5

7

4

Tip

30

7

4

Ring

6

6

1

Tip

31

6

1

Ring

7

6

2

Tip

32

6

2

Ring

8

6

3

Tip

33

6

3

Ring

9

6

4

Tip

34

6

4

Ring

10

8

2

Tip

35

8

2

Ring

11

8

3

Tip

36

8

3

Ring

12

8

4

Tip

37

8

4

Ring

Pins 13-17 and 38-42 are

13

38

not used

14

39

15

40

16

41

17

42

18

9

1

Tip

43

9

1

Ring

19

9

2

Tip

44

9

2

Ring

20

9

3

Tip

45

9

3

Ring

21

9

4

Tip

46

9

4

Ring

22

10

1

Tip

47

10

1

Ring

23

10

2

Tip

48

10

2

Ring

24

10

3

Tip

49

10

3

Ring

25

10

4

Tip

50

10

4

Ring

J10

1

15

1

Tip

26

15

1

Ring

Slots 13-17

2

16

1

Tip

27

16

1

Ring

3

16

2

Tip

28

16

2

Ring

4

16

3

Tip

29

16

3

Ring

5

16

4

Tip

30

16

4

Ring

6

17

1

Tip

31

17

1

Ring

7

17

2

Tip

32

17

2

Ring

8

17

3

Tip

33

17

3

Ring

9

17

4

Tip

34

17

4

Ring

10

15

2

Tip

35

15

2

Ring

11

15

3

Tip

36

15

3

Ring

12

15

4

Tip

37

15

4

Ring

Pins 13-17 and 38-42 are

13

38

not used

14

39

15

40

16

41

17

42

18

14

1

Tip

43

14

1

Ring

19

14

2

Tip

44

14

2

Ring

20

14

3

Tip

45

14

3

Ring

21

14

4

Tip

46

14

4

Ring

22

13

1

Tip

47

13

1

Ring

23

13

2

Tip

48

13

2

Ring

24

13

3

Tip

49

13

3

Ring

25

13

4

Tip

50

13

4

Ring
Table A-7: PSC CHAMP Connector Pinouts to Subscriber Line
Connector Pin Slot Line Tip/Ring Pin Slot Line Tip/Ring

J11

1

3

1

Tip

26

3

1

Ring

Slots 1-5

2

3

2

Tip

27

3

2

Ring

3

3

3

Tip

28

3

3

Ring

4

3

4

Tip

29

3

4

Ring

5

2

1

Tip

30

2

1

Ring

6

2

2

Tip

31

2

2

Ring

7

2

3

Tip

32

2

3

Ring

8

2

4

Tip

33

2

4

Ring

9

1

1

Tip

34

1

1

Ring

10

1

2

Tip

35

1

2

Ring

11

1

3

Tip

36

1

3

Ring

12

1

4

Tip

37

1

4

Ring

Pins 13-17 and 38-42 are

13

38

not used

14

39

15

40

16

41

17

42

18

4

1

Tip

43

4

1

Ring

19

4

2

Tip

44

4

2

Ring

20

4

3

Tip

45

4

3

Ring

21

4

4

Tip

46

4

4

Ring

22

5

1

Tip

47

5

1

Ring

23

5

2

Tip

48

5

2

Ring

24

5

3

Tip

49

5

3

Ring

25

5

4

Tip

50

5

4

Ring

J12

1

8

1

Tip

26

8

1

Ring

Slots 6-10

2

7

1

Tip

27

7

1

Ring

3

7

2

Tip

28

7

2

Ring

4

7

3

Tip

29

7

3

Ring

5

7

4

Tip

30

7

4

Ring

6

6

1

Tip

31

6

1

Ring

7

6

2

Tip

32

6

2

Ring

8

6

3

Tip

33

6

3

Ring

9

6

4

Tip

34

6

4

Ring

10

8

2

Tip

35

8

2

Ring

11

8

3

Tip

36

8

3

Ring

12

8

4

Tip

37

8

4

Ring

Pins 13-17 and 38-42 are

13

38

not used

14

39

15

40

16

41

17

42

18

9

1

Tip

43

9

1

Ring

19

9

2

Tip

44

9

2

Ring

20

9

3

Tip

45

9

3

Ring

21

9

4

Tip

46

9

4

Ring

22

10

1

Tip

47

10

1

Ring

23

10

2

Tip

48

10

2

Ring

24

10

3

Tip

49

10

3

Ring

25

10

4

Tip

50

10

4

Ring

J13

1

15

1

Tip

26

15

1

Ring

Slots 13-17

2

16

1

Tip

27

16

1

Ring

3

16

2

Tip

28

16

2

Ring

4

16

3

Tip

29

16

3

Ring

5

16

4

Tip

30

16

4

Ring

6

17

1

Tip

31

17

1

Ring

7

17

2

Tip

32

17

2

Ring

8

17

3

Tip

33

17

3

Ring

9

17

4

Tip

34

17

4

Ring

10

15

2

Tip

35

15

2

Ring

11

15

3

Tip

36

15

3

Ring

12

15

4

Tip

37

15

4

Ring

Pins 13-17 and 38-42 are

13

38

not used

14

39

15

40

16

41

17

42

18

14

1

Tip

43

14

1

Ring

19

14

2

Tip

44

14

2

Ring

20

14

3

Tip

45

14

3

Ring

21

14

4

Tip

46

14

4

Ring

22

13

1

Tip

47

13

1

Ring

23

13

2

Tip

48

13

2

Ring

24

13

3

Tip

49

13

3

Ring

25

13

4

Tip

50

13

4

Ring

J14

1

20

1

Tip

26

20

1

Ring

Slots 18-22

2

20

2

Tip

27

20

2

Ring

3

20

3

Tip

28

20

3

Ring

4

20

4

Tip

29

20

4

Ring

5

21

1

Tip

30

21

1

Ring

6

21

2

Tip

31

21

2

Ring

7

21

3

Tip

32

21

3

Ring

8

21

4

Tip

33

21

4

Ring

9

22

1

Tip

34

22

1

Ring

10

22

2

Tip

35

22

2

Ring

11

22

3

Tip

36

22

3

Ring

12

22

4

Tip

37

22

4

Ring

Pins 13-17 and 38-42 are

13

38

not used

14

39

15

40

16

41

17

42

18

19

1

Tip

43

19

1

Ring

19

19

2

Tip

44

19

2

Ring

20

19

3

Tip

45

19

3

Ring

21

19

4

Tip

46

19

4

Ring

22

18

1

Tip

47

18

1

Ring

23

18

2

Tip

48

18

2

Ring

24

18

3

Tip

49

18

3

Ring

25

18

4

Tip

50

18

4

Ring
Table A-8: CHAMP Connectors for xDSL Lines (to MC or LCC)
Connector Pin Slot Line Tip/Ring Pin Slot Line Tip/Ring

J3

1

4

1

Tip

26

3

1

Ring

Slots 1-4

2

4

1

Ring

27

3

1

Tip

3

4

2

Tip

28

3

2

Ring

4

4

2

Ring

29

3

2

Tip

5

4

3

Tip

30

3

3

Ring

6

4

3

Ring

31

3

3

Tip

7

4

4

Tip

32

3

4

Ring

8

4

4

Ring

33

3

4

Tip

Slots 9-25, and 50 are not

9

34

2

1

Ring

used

10

35

2

1

Tip

11

36

2

2

Ring

12

37

2

2

Tip

13

38

2

3

Ring

14

39

2

3

Tip

15

40

2

4

Ring

16

41

2

4

Tip

17

42

1

1

Ring

18

43

1

1

Tip

19

44

1

2

Ring

20

45

1

2

Tip

21

46

1

3

Ring

22

47

1

3

Tip

23

48

1

4

Ring

24

49

1

4

Tip

25

50

J4

1

22

1

Tip

26

21

1

Ring

Slots 19-22

2

22

1

Ring

27

21

1

Tip

3

22

2

Tip

28

21

2

Ring

4

22

2

Ring

29

21

2

Tip

5

22

3

Tip

30

21

3

Ring

6

22

3

Ring

31

21

3

Tip

7

22

4

Tip

32

21

4

Ring

8

22

4

Ring

33

21

4

Tip

Slots 9-25 and 50 are not

9

34

20

1

Ring

used

10

35

20

1

Tip

11

36

20

2

Ring

12

37

20

2

Tip

13

38

20

3

Ring

14

39

20

3

Tip

15

40

20

4

Ring

16

41

20

4

Tip

17

42

19

1

Ring

18

43

19

1

Tip

19

44

19

2

Ring

20

45

19

2

Tip

21

46

19

3

Ring

22

47

19

3

Tip

23

48

19

4

Ring

24

49

19

4

Tip

25

50

J5

1

8

1

Tip

26

7

1

Ring

slots 5-10

2

8

1

Ring

27

7

1

Tip

3

8

2

Tip

28

7

2

Ring

4

8

2

Ring

29

7

2

Tip

5

8

3

Tip

30

7

3

Ring

6

8

3

Ring

31

7

3

Tip

7

8

4

Tip

32

7

4

Ring

8

8

4

Ring

33

7

4

Tip

9

9

1

Tip

34

6

1

Ring

10

9

1

Ring

35

6

1

Tip

11

9

2

Tip

36

6

2

Ring

12

9

2

Ring

37

6

2

Tip

13

9

3

Tip

38

6

3

Ring

14

9

3

Ring

39

6

3

Tip

15

9

4

Tip

40

6

4

Ring

16

9

4

Ring

41

6

4

Tip

17

10

1

Tip

42

5

1

Ring

18

10

1

Ring

43

5

1

Tip

19

10

2

Tip

44

5

2

Ring

20

10

2

Ring

45

5

2

Tip

21

10

3

Tip

46

5

3

Ring

22

10

3

Ring

47

5

3

Tip

23

10

4

Tip

48

5

4

Ring

Slots 25 and 50 are not

24

10

4

Ring

49

5

4

Tip

used

25

10

50

J6

1

17

1

Tip

26

16

1

Ring

Slots 1-18

2

17

1

Ring

27

16

1

Tip

3

17

2

Tip

28

16

2

Ring

4

17

2

Ring

29

16

2

Tip

5

17

3

Tip

30

16

3

Ring

6

17

3

Ring

31

16

3

Tip

7

17

4

Tip

32

16

4

Ring

8

17

4

Ring

33

16

4

Tip

9

18

1

Tip

34

15

1

Ring

10

18

1

Ring

35

15

1

Tip

11

18

2

Tip

36

15

2

Ring

12

18

2

Ring

37

15

2

Tip

13

18

3

Tip

38

15

3

Ring

14

18

3

Ring

39

15

3

Tip

15

18

4

Tip

40

15

4

Ring

16

18

4

Ring

41

15

4

Tip

17

13

1

Tip

42

14

1

Ring

18

13

1

Ring

43

14

1

Tip

19

13

2

Tip

44

14

2

Ring

20

13

2

Ring

45

14

2

Tip

21

13

3

Tip

46

14

3

Ring

22

13

3

Ring

47

14

3

Tip

23

13

4

Tip

48

14

4

Ring

Pins 25 and 50 are not

24

13

4

Ring

49

14

4

Tip

used

25

50
Table A-9: CHAMP Connectors for ADSL Lines (Direct Connect)
Connector Pin Slot Line Tip/Ring Pin Slot Line Tip/Ring

J1

1

26

5

1

Ring

Slots 1,5

2

27

5

1

Tip

3

28

5

2

Ring

Pins 1-25 and pins 42-50

4

29

5

2

Tip

are not used

5

30

5

3

Ring

6

31

5

3

Tip

7

32

5

4

Ring

8

33

5

4

Tip

9

34

1

1

Ring

10

35

1

1

Tip

11

36

1

2

Ring

12

37

1

2

Tip

13

38

1

3

Ring

14

39

1

3

Tip

15

40

1

4

Ring

16

41

1

4

Tip

17

42

18

43

19

44

20

45

21

46

22

47

23

48

24

49

25

50

J2

1

18

3

Tip

26

22

3

Ring

Slots 18,22

2

18

3

Ring

27

22

3

Tip

3

18

4

Tip

28

22

4

Ring

4

18

4

Ring

29

22

4

Tip

Pins 5-25, 34-37, and

5

30

18

1

Ring

42-50 are not used

6

31

18

1

Tip

7

32

18

2

Ring

8

33

18

2

Tip

9

34

10

35

11

36

12

37

13

38

22

1

Ring

14

39

22

1

Tip

15

40

22

2

Ring

16

41

22

2

Tip

17

42

18

43

19

44

20

45

21

46

22

47

23

48

24

49

25

50

A.4 Card Slot/Connector Assignments

The following table shows the MDF, POTS, and ADSL CHAMP connectors and pins associated with each card slot.

This information is a different view of the information presented in other tables and figures in the "Installation - DOH Standard" chapter. For example, Figure A-15 illustrates the connectors and their tip/ring maps as they relate to the PSC. This figure is a subscriber line at the line interface module (LIM) view.

See the "Connecting the PSC to the MDF" section for a fuller discussion of how this view of information can be particularly useful.


Figure A-15: LIM/POTS Slot/Connector Assignments




hometocprevnextglossaryfeedbacksearchhelp
Posted: Tue Nov 16 09:10:51 PST 1999
Copyright 1989-1999©Cisco Systems Inc.