Table of Contents
Cisco 633 Connectors
The following illustration shows the connectors located on the rear panel of the Cisco 633.
Figure A-1: Rear View of the Cisco 633
The following ports are located on the backside of the 633.
The Serial interface uses 12-in-1 V.35 Data Terminal Equipment (DTE) serial connector. Connects to a 5-in-1 V.35 Data Communications Equipment (DCE) serial port on a Cisco router.
12-in-1 Connector to 5-in-1 Connector Pinouts
Table A-1: 12-in-1 to 5-in-1 Connector Pinouts
| 12-in-1 X.21 DCE to 5-in-1 X.21 DTE: P/N-??
|
|---|
FROM
| SB
| SIGNAL
| NOTE
| SIGNAL
| SB
| TO
|
J1-21
| X
| MODE_2
| LOCAL CONNECTIONS
| MODE_2
GND
GND
MODE_DCE
| X
X
X
X
| J2-47
J2-48
J2-51
J2-52
|
|
|
| SHIELD
| SHIELD GND
|
| J2-46
|
J1-5 J1-18
|
| I_RXD/TXD+
I_RXD/TXD-
| TWISTED PAIR # 5
| O_TXD/RXD+
O_TXD/RXD-
|
| J2-11
J2-12
|
J1-11 J1-10
|
| I_CTS/RTS+
I_CTS/RTS-
| TWISTED PAIR # 3
| O_RTS/CTS+
O_RTS/CTS-
|
| J2-9
J2-10
|
J1-1 J1-14
|
| O_TXD/RXD+
O_TXD/RXD-
| TWISTED PAIR # 8
| I_RXD/TXD+
I_RXD/TXD-
|
| J2-28
J2-27
|
J1-8 J1-9
|
| O_RTS/CTS+
O_RTS/CTS-
| TWISTED PAIR # 2
| I_CTS/RTS+
I_CTS/RTS-
|
| J2-1
J2-2
|
J1-2 J1-15
|
| O_TXCE/RXC+
O_TXCE/RXC-
| TWISTED PAIR # 7
| I_RXC/TXCE+
I_RXC/TXCE-
|
| J2-26
J2-25
|
J1-26
| X
| GND
NOT USED
| TWISTED PAIR # 1
| GND
NOT USED
|
| J2-15
|
|
| NOT USED
NOT USED
| TWISTED PAIR # 4
| NOT USED
NOT USED
|
|
|
|
| NOT USED
NOT USED
|
TWISTED PAIR # 6
| NOT USED
NOT USED
|
|
|
|
| NOT USED
NOT USED
| TWISTED PAIR # 9
| NOT USED
NOT USED
|
|
|
J1 is 12-in-1 plug and J2 is 5-in-1 plug. J1 is DCE and J2 is DTE
SB = Shorting Block
X = Connection to Shorting Block
Note: Shorting Block on J2 should be grouped as shown
|
|---|
Figure A-2: Front View of Serial Connector
The management port uses an RJ-45 connector.
The connector pinouts for the management port are shown in the following table.
Table A-2:
| Pin
| Signal
|
|---|
4
| Ground
|
5
| RX
|
6
| TX
|
Management Connector Pinouts
Figure A-3: Front View of Management Connector
The Symmetric Digital Subscriber Line (ADSL) port uses an RJ-11 connector. The following table shows the connector pinouts for the ADSL connector.
Table A-3:
SDSL Connector Pinouts
Figure A-4: Front View of SDSL Connector
Posted: Mon Jan 10 12:58:38 PST 2000
Copyright 1989-2000©Cisco Systems Inc.
