Product Overview

Physical and Functional Overviews

Power Entry Module Card

Controller Card

OC-12c/STM-4 and OC-48c/STM-16 Line Cards

BWDM Line Card

Switch Card

Fan Tray

System Specifications

Agency Approvals

Product Overview

This chapter provides physical and functional overviews of the ONS 15190 IP Transport Concentrator. It contains physical descriptions of the concentrator hardware and major components, and functional descriptions of the hardware-related features.

The ONS 15190 is a telco-grade, high-speed, layer 1 intelligent concentrator that complements the Cisco Dynamic Packet Transport (DPT) family of products. Supporting up to 16 OC-12c/STM-4 rings or 8 OC-48c/STM-16 rings, the ONS 15190 enables the definition of logical rings over physical star infrastructure in DPT environments.

ONS 15190 features follow:

Combines the advantages of star wiring with the resilience of ring topologies.
Optimizes spatial bandwidth reuse through in-service ring rearrangement.
Increases network reliability through enhanced intelligent protection switching (E-IPS).
Improves network scalability and serviceability.
Offers a sophisticated centralized ring management and monitoring system.
Reduces network exposure to human error.
Reduces overhead costs.

The ONS 15190 provides a high-level of system redundancy, hot-swappable cards, a 6-fan cooling unit, and system temperature monitoring. The unit can be configured and controlled locally via a RS-232C serial connection or remotely via Ethernet.

ONS 15190 overview information is presented in the following sections:

Physical and Functional Overviews

The ONS 15190 chassis contains 16 physical slots and a fan mechanism at the bottom.

Figure 1-1: ONS 15190 Front View

The ONS 15190 chassis can contain the following cards:

Power entry module (PEM)—The PEM slot contains up to two PEMs, each of which requires a -48V DC power source. One PEM is sufficient for operation of the unit; two are required for system redundancy.
Controller card—The controller slots are C1 and C2. Up to two cards may be used for complete redundancy; one is sufficient for operation of the unit.
Line cards—Eight line card slots (L1 to L8) support up to eight line cards. Two-port OC-12c/STM-4 and OC-48c/STM-16 line cards provide two connector pairs (Tx, Rx) each, which are used to connect nodes to the unit. Four-port OC-12c/STM-4 line cards provide four such connector pairs. BWDM line cards provide two single connectors, each of which support bidirectional traffic.
Switch cards—Slots S1 to S5 are used to house up to five switch cards. For OC-12c/STM-4 operation using only two-port cards, one switch card is required and a second card may be used for 1+1 redundancy. When four-port line cards are used, five switch cards are required for normal use. For OC-48c/STM-16, four switch cards are required and the fifth may be used for redundancy.
Fan Tray —Contains six fans extends across the bottom of the unit (below the card slots) to cool the unit.

Power Entry Module Card

The PEM slot is the left-most slot on the unit. This slot can hold either one or two PEM cards. Each card contains the following:

Power indicator—Lit green when the power is on and red when there is a problem with the PEM.
Optional On/Off switch—Powers the module on and off.
-48V DC connector—Provides power to the system. Supplied power may be between -40 to -70V DC.

Figure 1-2: PEM Cards Front Panel

Controller Card

Slots titled C1 and C2 in the unit are for controller cards. One card is required; the second is for system redundancy.

Figure 1-3: Controller Card Front Panel

Three LED signals at the top of the controller card indicate the operational status of the card:

PWR—Green indicates the card is powered.
ACT—Indicates that the card is functioning properly. When the controller card is the active controller, this LED flashes at the same rate as all other cards in the unit (1 second on, 1 second off). When the controller card is on standby (for control redundancy), this LED flashes approximately four times slower than the other cards in the unit.
FAIL—Red indicates that there is a problem with the card.

The RESET button may be used to reset the card.

The CONSOLE/MAINT (maintenance) connections are used to connect the unit to a local RS-232C cable in order to configure and control the ONS 15190.

CONSOLE—Controls the active controller card (even if the connection is to the redundant controller card).
MAINT—Controls only the controller card to which it is attached.

Note You can connect only to one of the CONSOLE ports at any one time because this port controls both controller cards.

The Ethernet connection is used to connect the unit to a LAN network. The Ethernet ports of both controller cards should be connected to a LAN network.

LINK LED—Indicates that the Ethernet link is active.
DATA LED—Indicates that the Ethernet connection is transmitting or receiving data.

Controller cards are hot swappable, and if a controller card fails, the second controller card takes over operation of the system automatically. The system is operable without a controller card, with the following limitations:

No configuration may be performed, including addition of line cards.

No system messages will be received.

AIS will not be mirrored.
Path trace will not be mirrored (when in transparent mode).
E-IPS and Autotracker options will not function.
Counters will be lost.
If switch cards are removed while four-port line cards are in use, the system can stop operating.

OC-12c/STM-4 and OC-48c/STM-16 Line Cards

Two-port OC-12c/STM-4 and OC-48c/STM-16 line cards are used to connect two OC-12c/STM-4 or OC-48c/STM-16 connections, respectively, to the ONS 15190. Four-port OC-12c/STM-4 line cards can be used to connect up to four OC-12c/STM-4 connections each.

Note OC-12/STM-4 nodes or line cards cannot be connected to OC-48/STM-16 nodes or line cards.

Each line card contains three LEDs (PWR, ACT, FAIL) to indicate the operational status of the card (See the section "Controller Card"). When the line card is initialized, the ACT LED flashes very fast; when the card is operational, the ACT LED flashes at a constant rate of once per second in synchronization with the active controller card.

In addition, each line card contains either two or four ports. Each port contains a pair of optical fiber connectors that are used to connect one transmit and one receive line from the connected node.

Warning Invisible laser radiation may be emitted from the aperture ports of single-mode line cards when no fiber cable is connected. Avoid exposure and do not stare into open apertures to avoid permanent eye damage.

Figure 1-4: OC-12/STM-4 Single-Mode Line Card Front Panel

Figure 1-5: OC-48c/STM-16 Single-Mode Line Card

Each port has five associated LEDs that indicate the status of the respective connection:

ACTIVE—Indicates that the port is part of an operational ring/connection.
CARRIER—Indicates that there is light in the specific receiving port.
RX PKT—Indicates that the line is actively receiving data.
A and B—Indicates whether the port is Receive Outer/Transmit Inner (A) or Transmit Outer/Receive Inner (B) for SRP.

BWDM Line Card

The bidirectional wavelength division multiplexing (BWDM) line card is used to connect two bidirectional WDM fiber-optic connections.

Figure 1-6: Representation of Bidirectional WDM

Each line card contains three LEDs (PWR, ACT, FAIL) to indicate the operational status of the card. (See section "Controller Card".) When the line card is initialized, the ACT LED flashes very fast; when the card is operational, the ACT LED flashes at a constant rate of once per second in synchronization with the active controller card.

Figure 1-7: OC-12/STM-4 BWDM Line Card Front Panel

In addition, each BWDM line card contains two ports. Each port contains one optical fiber connector that is used to connect one bidirectional line from the connected node. When connecting BWDM cards between ONS 15190 systems, port 1 of the BWDM card must be connected to port 2 of the second BWDM card and visa versa.

Each port has five associated LEDs which indicate the status of the respective connection:

ACTIVE—Indicates that the port is part of an operational ring/connection.
CARRIER—Indicates that there is light in the specific receiving port.
RX PKT—Indicates that the line is actively receiving data.
A and B—Indicates whether the port is Receive Outer/Transmit Inner (A) or Transmit Outer/Receive Inner (B) for SRP.

Switch Card

Up to five switch cards may be installed in the ONS 15190 unit. For OC-12c/ STM-4 operation with two-port line cards, one switch card is required, with a second card providing 1+1 redundancy. For OC-12c/STM-4 operation with four-port line cards, five switch cards are required for normal operation and complete system redundancy.

Note The ONS 15190 with four-port OC-12c/STM-4 line cards can be operated with only two switch cards; however system redundancy and use of a sniff node are only enabled when all five switch cards are operational. If the number of switch cards is reduced from five to two, a controller card must be active to ensure proper operation of the line cards.

For OC-48c/STM-16, four switch cards are required, with the fifth providing 4+1 redundancy. Each switch card contains three LEDs (PWR, ACT, FAIL) to indicate the operational status of the card. (See section "Controller Card".) Switch cards are hot swappable and feature automatic fault detection and switch over with no data loss.

Figure 1-8: Switch Card Front Panel

Fan Tray

The fan tray located on the bottom of the ONS 15190 unit cools the unit during normal operation. The fan tray is hot swappable, and the system can function without the fan mechanism. It is recommended not to remove the fan tray for more than 5 minutes because the concentrator components can become over-heated.

The fan tray contains six fans, Operation of the system can continue almost indefinitely even if one of the fans is not operational. If any of the fans fail, a warning message appears on the screen connected to the control card. It is recommended to have a spare fan tray available in the event of a fan failure.

By default, the system will continue operation as long as the cards' temperature remains below 167°F (75°C). If the temperature on any of the individual cards exceeds this temperature, the card stops operation. This temperature-protection mechanism can be changed via the CLI commands.

The temperature of any card can also be verified via the CLI, as shown in the following example:

  
admin> card l1 show status
Line Card 1:
Subtype:            Single Mode IR SC OC12c/STM4 SRP line card w/2 ports
# of ports:         2
State:              Operational
Catalog number:     OC12/STM4-SM-IR-SRP
Serial number:      1030-008
Board version:      A4
Temperature Status: Normal
Temperature 1:       41.5 degC (106.7 degF)
Temperature 2:         35.0 degC (95.0 degF)

System Specifications

ONS 15190 specifications are presented in three tables:

Table 1-1 lists the physical specifications.
Table 1-2 lists the electrical specifications.
Table 1-3 lists the environmental specifications.

Table 1-1: ONS 15190 Physical Specifications

Description Value

Frame dimensions (h x w x d)

15.75 in. (400 mm) (9 U) x 19 in. (482 mm) x
14.4 in. (386 mm)

Weight:

Maximum configuration
Shipping

52.8 lb (24 kg)
66 lb (30 kg)

Description	Value
Frame dimensions (h x w x d)	15.75 in. (400 mm) (9 U) x 19 in. (482 mm) x 14.4 in. (386 mm)
Weight: Maximum configuration Shipping	52.8 lb (24 kg) 66 lb (30 kg)

Table 1-2: ONS 15190 Electrical Specifications

Description Value

DC-input power

-48V DC

Maximum power consumption
(fully loaded)

OC-12/STM-4—350W
OC-48/STM-4—600W

Description	Value
DC-input power	-48V DC
Maximum power consumption (fully loaded)	OC-12/STM-4—350W OC-48/STM-4—600W

Table 1-3: ONS 15190 Environmental Specifications

Description Value

Temperature (operating)

32°F (0°C) to 104°F (40°C)

Temperature (non-operating)

-4°F (-20°C) to 149°F (65°C)

Relative humidity (noncondensing)

10% to 90%

Vibration (operating)

5 to 200 Hz, 0.5g (1 oct/min)

Vibration (non-operating)

5 to 200 Hz, 1g (1 oct/min)
200 to 500 Hz, 2g (1 oct/min)

Description	Value
Temperature (operating)	32°F (0°C) to 104°F (40°C)
Temperature (non-operating)	-4°F (-20°C) to 149°F (65°C)
Relative humidity (noncondensing)	10% to 90%
Vibration (operating)	5 to 200 Hz, 0.5g (1 oct/min)
Vibration (non-operating)	5 to 200 Hz, 1g (1 oct/min) 200 to 500 Hz, 2g (1 oct/min)

Agency Approvals

The ONS 15190 meets the agency approvals for safety and EMI as listed in Table 1-4.

Table 1-4: Agency Approvals

Category Agency Approval

Safety

UL 1950, Third Edition (US)

CSA C22.2, No. 950-95, Third Edition (Canada)

EN/IEC 60950 (EC, Japan)

EN 41003

AUSTEL TS001

AS/NZS 3260 (Australia)

EN 60825 Laser Safety (Class 1)

EMI

FCC subpart B Class A (US)

AS/NZS 3548 Class A (Australia)

EMC Directive 89/336/EEC:
  EN 55022 Class A
  EN 6100-3-2
  EN 55024

VCCI Class A (Japan)

Category	Agency Approval
Safety	UL 1950, Third Edition (US)
	CSA C22.2, No. 950-95, Third Edition (Canada)
	EN/IEC 60950 (EC, Japan)
	EN 41003
	AUSTEL TS001
	AS/NZS 3260 (Australia)
	EN 60825 Laser Safety (Class 1)
EMI	FCC subpart B Class A (US)
	AS/NZS 3548 Class A (Australia)
	EMC Directive 89/336/EEC: EN 55022 Class A EN 6100-3-2 EN 55024
	VCCI Class A (Japan)

Table of Contents

Product Overview