|
|
To continue your PA-8E Ethernet port adapter installation, you must configure the ethernet interfaces. The instructions that follow apply to all supported platforms. Minor differences between the platforms are noted. This chapter contains the following sections:
You modify the configuration of your router through the software command interpreter called EXEC. You must enter the privileged level of the EXEC command interpreter (also called enable mode) with the enable command before you can use the configure command to configure a new interface or to change the existing configuration of an interface. The system prompts you for a password if one has been set.
The system prompt for the privileged level ends with a pound sign (#) instead of an angle bracket (>). At the console terminal, use the following procedure to enter the privileged level:
Router> enable
Password:
Step 2 Enter the password (the password is case sensitive). For security purposes, the password is not displayed.
When you enter the correct password, the system displays the privileged-level system prompt (#):
Router#
After you verify that the new PA-8E is installed correctly (the ENABLED LED lights), use the privileged-level configure command to configure the new interfaces. Be prepared with the information you will need, such as the following:
For a summary of the configuration options available, refer to the appropriate configuration publications listed in the "Cisco Connection Online" section.
The configure command requires privileged-level access to the EXEC command interpreter, which usually requires a password. Contact your system administrator, if necessary, to obtain EXEC-level access.
 |
Note The PA-8E interfaces can both be configured at 10 Mbps, half duplex (HDX), for a maximum aggregate bandwidth of 80 Mbps. |
After you verify that the new PA-8E is installed correctly (the enabled LED goes on), use the privileged-level configure command to configure the new interfaces. Have the following information available:
If you installed a new PA-8E or if you want to change the configuration of an existing interface, you must enter configuration mode to configure the new interfaces. If you replaced a PA-8E that was previously configured, the system recognizes the new interfaces and brings each of them up in their existing configuration.
For a summary of the configuration options available and instructions for configuring interfaces on a PA-8E, refer to the appropriate configuration publications listed in the "Related Documentation" section.
You execute configuration commands from the privileged level of the EXEC command interpreter, which usually requires password access. Contact your system administrator, if necessary, to obtain password access. (See the "Using the EXEC Command Interpreter" section for an explanation of the privileged level of the EXEC.)
This section contains the following subsections:
Before you remove an interface that you will not replace, or replace port adapters, use the shutdown command to shut down (disable) the interfaces to prevent anomalies when you reinstall the new or reconfigured port adapter. When you shut down an interface, it is designated administratively down in the show command displays.
Follow these steps to shut down an interface:
Step 2 At the privileged-level prompt, enter configuration mode and specify that the console terminal is the source of the configuration subcommands, as follows:
Router# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)#
Step 3 Shut down interfaces by entering the interface ethernet subcommand (followed by the interface address of the interface), and then enter the shutdown command. Table 4-1 shows the command syntax.
When you have finished, press Ctrl-Z—hold down the Control key while you press Z—or enter end or exit to exit configuration mode and return to the EXEC command interpreter.
| Platform | Command | Example |
|---|---|---|
Catalyst RSM/VIP2 in Catalyst 5000 family switches | interface, followed by the type (ethernet) and slot/port (port-adapter-slot-number/ | The example is for interface 0 and interface 1 on a port adapter in port adapter slot 1. Router(config-if)# interface ethernet 1/0 Router(config-if)# shutdown Router(config-if)# interface ethernet 1/1 Router(config-if)# shutdown Ctrl-Z Router# |
Cisco 7120 series routers | interface, followed by the type (ethernet) and slot/port (port-adapter-slot-number/ | The example is for interface 0 and interface 1 on a port adapter in port adapter slot 3. Router(config-if)# interface ethernet 3/0 Router(config-if)# shutdown Router(config-if)# interface ethernet 3/1 Router(config-if)# shutdown Ctrl-Z Router# |
Cisco 7140 series routers | interface, followed by the type (ethernet) and slot/port (port-adapter-slot-number/ | The example is for interface 0 and interface 1 on a port adapter in port adapter slot 4. Router(config-if)# interface ethernet 4/0 Router(config-if)# shutdown Router(config-if)# interface ethernet 4/1 Router(config-if)# shutdown Ctrl-Z Router# |
Cisco 7200 series routers | interface, followed by the type (ethernet) and slot/port (port-adapter-slot-number/ | The example is for interface 0 and interface 1 on a port adapter in port adapter slot 6. Router(config-if)# interface ethernet 6/0 Router(config-if)# shutdown Router(config-if)# interface ethernet 6/1 Router(config-if)# shutdown Ctrl-Z Router# |
Cisco uBR7223 router | interface, followed by the type (ethernet) and slot/port (port-adapter-slot-number/ | The example is for interface 0 and interface 1 on a port adapter in port adapter slot 1. Router(config-if)# interface ethernet 1/0 Router(config-if)# shutdown Router(config-if)# interface ethernet 1/1 Router(config-if)# shutdown Ctrl-Z Router# |
Cisco uBR7246 router | interface, followed by the type (ethernet) and slot/port (port-adapter-slot-number/ | The example is for interface 0 and interface 1 on a port adapter in port adapter slot 2. Router(config-if)# interface ethernet 2/0 Router(config-if)# shutdown Router(config-if)# interface ethernet 2/1 Router(config-if)# shutdown Ctrl-Z Router# |
VIP2 in Cisco 7000 series or | interface, followed by the type (ethernet) and slot/port adapter/port (interface-processor-slot-number/ | The example is for interface 1 and interface 0 on a port adapter in port adapter slot 1 of a VIP2 installed Router(config-if)# interface ethernet 1/1/1 Router(config-if)# shutdown Router(config-if)# interface ethernet 1/1/0 Router(config-if)# shutdown Ctrl-Z Router# |
|
Note If you need to shut down additional interfaces, enter the interface ethernet command (followed by the interface address of the interface) for each of the interfaces on your port adapter. Use the no shutdown command to enable the interface. |
Step 4 Write the new configuration to NVRAM as follows:
Router# copy running-config startup-config [OK] Router#
The system displays an OK message when the configuration has been stored in NVRAM.
Step 5 Verify that new interfaces are now in the correct state (shut down) using the
show interfaces command (followed by the interface type and interface address of the interface) to display the specific interface. Table 4-2 provides examples.
| Platform | Command | Example |
|---|---|---|
Catalyst RSM/VIP2 in Catalyst 5000 family switches | show interfaces ethernet, followed by slot/port (port-adapter-slot-number/ | The example is for interface 0 on a port adapter in port adapter slot 1. Router# show interfaces ethernet 1/0 ethernet 1/0 is administratively down, line protocol is down [Additional display text omitted from this example] |
Cisco 7120 series routers | show interfaces ethernet, followed by slot/port (port-adapter-slot-number/ | The example is for interface 0 on a port adapter in port adapter slot 3. Router# show interfaces ethernet 3/0 ethernet 3/0 is administratively down, line protocol is down [Additional display text omitted from this example] |
Cisco 7140 series routers | show interfaces ethernet, followed by slot/port (port-adapter-slot-number/ | The example is for interface 0 on a port adapter in port adapter slot 4. Router# show interfaces ethernet 4/0 ethernet 4/0 is administratively down, line protocol is down [Additional display text omitted from this example] |
Cisco 7200 series routers | show interfaces ethernet, followed by slot/port (port-adapter-slot-number/ | The example is for interface 0 on a port adapter in port adapter slot 6. Router# show interfaces ethernet 6/0 ethernet 6/0 is administratively down, line protocol is down [Additional display text omitted from this example] |
Cisco uBR7223 router | show interfaces ethernet, followed by slot/port (port-adapter-slot- number/ | The example is for interface 0 on a port adapter in port adapter slot 1. Router# show interfaces ethernet 1/0 ethernet 1/0 is administratively down, line protocol is down [Additional display text omitted from this example] |
Cisco uBR7246 router | show interfaces ethernet, followed by slot/port (port-adapter-slot-number/ | The example is for interface 0 on a port adapter in port adapter slot 2. Router# show interfaces ethernet 2/0 ethernet 2/0 is administratively down, line protocol is down [Additional display text omitted from this example]
|
VIP2 in Cisco 7000 series or Cisco 7500 series routers | show interfaces ethernet, followed by slot/port adapter/port (interface-processor-slot-number/ | The example is for interface 0 on a port adapter in port adapter slot 1 of a VIP2 in interface processor slot 1. Router# show interfaces ethernet 1/1/0 ethernet 1/1/0 is administratively down, line protocol is down [Additional display text omitted from this example] |
Step 6 Reenable interfaces by doing the following:
a. Repeat Step 3 to reenable an interface. Substitute the no shutdown command for the shutdown command.
b. Repeat Step 4 to write the new configuration to memory. Use the
copy running-config startup-config command.
c. Repeat Step 5 to verify that the interfaces are in the correct state. Use the
show interfaces command followed by the interface type and interface address of the interface.
For complete descriptions of software configuration commands, refer to the publications listed in the "Related Documentation" section.
Following are instructions for a basic configuration: enabling an interface, and specifying IP routing. You might also need to enter other configuration subcommands, depending on the requirements for your system configuration and the protocols you plan to route on the interface. For complete descriptions of configuration subcommands and the configuration options available for ethernet interfaces, refer to the appropriate software documentation.
In the following procedure, press the Return key after each step unless otherwise noted. At any time you can exit the privileged level and return to the user level by entering disable at the prompt as follows:
Router# disable Router>
Router# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)#
Step 2 Specify the first interface to configure by entering the interface ethernet subcommand, followed by the interface address of the interface you plan to configure. (The command for your port adapter may be different, for example, interface atm.) Table 4-3 provides examples.
| Platform | Command | Example |
|---|---|---|
Catalyst RSM/VIP2 in Catalyst 5000 family switches | interface ethernet, followed by slot/port (port-adapter-slot-number/ | The example is for the first interface of a port adapter in port adapter slot 0. Router(config)# interface ethernet 0/0 Router(config-if)# |
Cisco 7120 series routers | interface ethernet, followed by slot/port (port-adapter-slot-number/ | The example is for the first interface of a Router(config)# interface ethernet 3/0 Router(config-if)# |
Cisco 7140 series routers | interface ethernet, followed by slot/port (port-adapter-slot-number/ | The example is for the first interface of a Router(config)# interface ethernet 4/0 Router(config-if)# |
Cisco 7200 series routers | interface ethernet, followed by slot/port (port-adapter-slot-number/ | The example is for the first interface of a Router(config)# interface ethernet 6/0 Router(config-if)# |
Cisco uBR7223 router | interface ethernet, followed by slot/port (port-adapter-slot-number/ | The example is for the first interface of a Router(config)# interface ethernet 1/0 Router(config-if)# |
Cisco uBR7246 router | interface ethernet, followed by slot/port (port-adapter-slot-number/ | The example is for the first interface of a Router(config)# interface ethernet 2/0 Router(config-if)# |
VIP2 in Cisco 7000 series or Cisco 7500 series routers | interface ethernet, followed by slot/port adapter/port (interface-processor-slot-number/ | The example is for the first interface of a Router(config)# interface ethernet 1/1/0 Router(config-if)# |
Step 3 Assign an IP address and subnet mask to the interface (if IP routing is enabled on the system) by using the ip address subcommand, as in the following example:
Router(config-if)# ip address 10.0.0.0 10.255.255.255
Step 4 Add any additional configuration subcommands required to enable routing protocols and set the interface characteristics.
Step 5 Reenable the interfaces using the no shutdown command. (See the "Shutting Down an Interface" section.)
Step 6 Configure all additional port adapter interfaces as required.
Step 7 After including all of the configuration subcommands to complete your configuration, press Ctrl-Z—hold down the Control key while you press Z—or enter end or exit to exit configuration mode and return to the EXEC command interpreter prompt.
Step 8 Write the new configuration to NVRAM as follows:
Router# copy running-config startup-config [OK] Router#
This completes the procedure for creating a basic configuration.
After configuring the new interface, use the show commands to display the status of the new interface or all interfaces, and use the ping and loopback commands to check connectivity. This section includes the following subsections:
Table 4-4 demonstrates how you can use the show commands to verify that new interfaces are configured and operating correctly and that the PA-8E appears in them correctly. Sample displays of the output of selected show commands appear in the sections that follow. For complete command descriptions and examples, refer to the publications listed in the "Related Documentation" section.
|
Note The ouputs that appear in this document may not match the output you receive when running these commands. The outputs in this document are examples only. |
| Command | Function | Example | ||
|---|---|---|---|---|
show version or | Displays system hardware configuration, the number of each interface type installed, Cisco IOS software version, names and sources of configuration files, and boot images | Router# show version | ||
show controllers | Displays all the current interface processors and their interfaces | Router# show controllers | ||
show diag slot
| Displays types of port adapters installed in your system and information about a specific port adapter slot, interface processor slot, or chassis slot | Router# show diag 2 | ||
show interfaces type 0 or 1/ | Displays status information about a specific type of interface (for example, serial) on a Catalyst RSM/VIP2 | Router# show interfaces serial 1/0 | ||
show interfaces type 3/interface-port- | Displays status information about a specific type of interface (for example, serial) in a Cisco 7120 series router | Router# show interfaces serial 3/1 | ||
show interfaces type 4/interface-port- | Displays status information about a specific type of interface (for example, serial) in a Cisco 7140 series router | Router# show interfaces serial 4/1 | ||
show interfaces type port-adapter-slot-number/ | Displays status information about a specific type of interface (for example, serial) in a Cisco 7200 series router | Router# show interfaces serial 1/0 | ||
show interfaces type 1/interface-port- | Displays status information about a specific type of interface (for example, serial) in a Cisco uBR7223 router | Router# show interfaces serial 1/1 | ||
show interfaces type 1 or 2/ | Displays status information about a specific type of interface (for example, serial) in a Cisco uBR7246 router | Router# show interfaces serial 2/0 | ||
show interfaces type interface-processor- | Displays status information about a specific type of interface (for example, serial) on a VIP2 in a Cisco 7000 series or Cisco 7500 series router | Router# show interfaces serial 3/1/0 | ||
show protocols | Displays protocols configured for the entire system and for specific interfaces | Router# show protocols | ||
show running-config | Displays the running configuration file | Router# show running-config | ||
show startup-config | Displays the configuration stored in NVRAM | Router# show startup-config |
Choose the subsection appropriate for your system. Proceed to the "Using the ping Command to Verify Network Connectivity" section when you have finished using the show commands.
Display the configuration of the system hardware, the number of each interface type installed, the Cisco IOS software version, the names and sources of configuration files, and the boot images, using the show version (or show hardware) command.
|
Note The ouputs that appear in this document may not match the output you receive when running these commands. The outputs in this document are examples only. |
Following is an example of the show version command from a Catalyst 5000 family switch with the PA-8E:
Router# show version Cisco Internetwork Operating System Software IOS (tm) GS Software (RSP-A), Version 12.0(471) [mpo 105] Copyright (c) 1986-1995 by cisco Systems, Inc. Image text-base: 0x600088A0, data-base: 0x605A4000 ROM: System Bootstrap, Version 5.3(16645) honda uptime is 4 hours, 22 minutes System restarted by reload System image file is "slot0:rsp-a111-1", booted via slot0 cisco RSP2 (R4600) processor with 32768K bytes of memory. R4600 processor, Implementation 32, Revision 2.0 Last reset from power-on G.703/E1 software, Version 1.0. Bridging software. X.25 software, Version 2.0, NET2, BFE and GOSIP compliant. Chassis Interface. 1 VIP2 controllers (16 Ethernet). 16 Ethernet/IEEE 802.3 interfaces. 125K bytes of non-volatile configuration memory. 20480K bytes of Flash PCMCIA card at slot 0 (Sector size 128K). 8192K bytes of Flash internal SIMM (Sector size 256K). No slave installed in slot 6. Configuration register is 0x2
Following is an example of the show version command from a Cisco 7200 series router with the PA-8E
Router# show version Cisco Internetwork Operating System Software IOS (tm) 7200 Software (C7200-J-M), Version 11.1(472) [biff 105] Copyright (c) 1986-1996 by cisco Systems, Inc. Image text-base: 0x600088A0, data-base: 0x605A4000 ROM: System Bootstrap, Version 12.0(10979) RELEASED SOFTWARE Router uptime is 8 hours, 22 minutes System restarted by reload System image file is "slot0:c7200-j-mz.960421", booted via slot0 cisco 7200 (R4700) processor with 22528K/10240K bytes of memory. R4700 processor, Implementation 33, Revision 1.0 Last reset from power-on Bridging software. X.25 software, Version 2.0, NET2, BFE and GOSIP compliant. Chassis Interface. 4 Ethernet/IEEE 802.3 interfaces. 5 FastEthernet/IEEE 802.3 interfaces. 125K bytes of non-volatile configuration memory. 20480K bytes of Flash PCMCIA card at slot 0 (Sector size 128K). 8192K bytes of Flash internal SIMM (Sector size 256K). Configuration register is 0x2
Following is an example of the show version command from a Cisco 7500 series router with the PA-8E:
Router# show version Cisco Internetwork Operating System Software IOS (tm) GS Software (RSP-A), Version 12.0(471) [mpo 105] Copyright (c) 1986-1995 by cisco Systems, Inc. Image text-base: 0x600088A0, data-base: 0x605A4000 ROM: System Bootstrap, Version 5.3(16645) honda uptime is 4 hours, 22 minutes System restarted by reload System image file is "slot0:rsp-a111-1", booted via slot0 cisco RSP2 (R4600) processor with 32768K bytes of memory. R4600 processor, Implementation 32, Revision 2.0 Last reset from power-on G.703/E1 software, Version 1.0. Bridging software. X.25 software, Version 2.0, NET2, BFE and GOSIP compliant. Chassis Interface. 1 VIP2 controllers (16 Ethernet). 16 Ethernet/IEEE 802.3 interfaces. 125K bytes of non-volatile configuration memory. 20480K bytes of Flash PCMCIA card at slot 0 (Sector size 128K). 8192K bytes of Flash internal SIMM (Sector size 256K). No slave installed in slot 6. Configuration register is 0x2
Display the types of port adapters installed in your system (and specific information about each) using the show diag slot command, where slot is the port adapter slot in a Cisco 7100 series,
Cisco 7200 series, and Cisco uBR7200 series router and the interface processor slot in a Cisco 7000 series or Cisco 7500 series router with a VIP2.
|
Note The ouputs that appear in this document may not match the output you receive when running these commands. The outputs in this document are examples only. |
|
Note The slot argument is not required for Catalyst 5000 family switches. |
Following is an example of the show diag command that shows a PA-8E on a
Catalyst RSM/VIP2:
Router# show diag 0
Slot 0:
Ethernet port adapter, 8 ports
Port adapter is analyzed
Port adapter insertion time 2d09h ago
Hardware revision 1.14 Board revision A0
Serial number 4294967295 Part number 73-1556-04
Test history 0x0 RMA number 00-00-00
EEPROM format version 1
EEPROM contents (hex):
0x20:01 01 01 0E FF FF FF FF 49 06 14 04 00 00 00 00
0x30:50 00 00 00 FF FF FF FF FF FF FF FF FF FF FF FF
Slot database information:
Flags: 0x4 Insertion time: 0x1DEC (2d00h ago)
Following is an example of the show diag slot command that shows a PA-8E in port adapter slot 4 of a Cisco 7200 series router:
Router# show diag 4 Slot 4: Ethernet port adapter, 8 ports Port adapter is analyzed Port adapter insertion time 2d09h ago Hardware revision 1.1 Board revision A0 Serial number 4294967295 Part number 73-1556-04 Test history 0x0 RMA number 00-00-00 EEPROM format version 1 EEPROM contents (hex): 0x20: 01 02 01 01 FF FF FF FF 49 06 14 04 00 00 00 00 0x30: 50 00 00 00 FF FF FF FF FF FF FF FF FF FF FF FF
Port adapters used with the Cisco 7200 VXR and Cisco uBR7246 VXR routers require the correct base hardware revision to function. The following error message will occur on bootup if the incorrect hardware revision is used: PA-3-REVNOTSUPPORTED:PA in slot 1 (Ethernet) requires base h/w revision of (1.14) for this chassisUse the show diag command to display the hardware revision.
|
Note For complete command descriptions and examples for Cisco 7200 series routers, Cisco 7100 series routers, and Cisco uBR7200 series universal broadband routers, refer to the publications listed in the "Cisco Connection Online" section. |
Following is an example of the show diag slot command that shows a PA-8E in port adapter
slot 0 on a VIP2 in interface processor slot 4:
Router# show diag 4
Slot 4:
Ethernet port adapter, 8 ports
Port adapter is analyzed
Port adapter insertion time 2d09h ago
Hardware revision 1.14 Board revision A0
Serial number 4294967295 Part number 73-1556-04
Test history 0x0 RMA number 00-00-00
EEPROM format version 1
EEPROM contents (hex):
0x20:01 01 01 0E FF FF FF FF 49 06 14 04 00 00 00 00
0x30:50 00 00 00 FF FF FF FF FF FF FF FF FF FF FF FF
Slot database information:
Flags: 0x4 Insertion time: 0x1DEC (2d00h ago)
Controller Memory Size: 8 MBytes
PA Bay 1 Information:
Ethernet PA, 8 ports
EEPROM format version 1
HW rev 1.1, Board revision 80
Serial number: 02825590 Part number: 73-1391-04
|
Note For complete VIP2 command descriptions and examples, refer to the publications listed in the "Cisco Connection Online" section. |
For complete descriptions of interface subcommands and the configuration options available for Catalyst RSM/VIP2, Cisco 7100 series, Cisco 7200, Cisco uBR7200 series, and VIP2 interfaces, refer to the publications listed in the "Related Documentation" section.
|
Note The ouputs that appear in this document may not match the output you receive when running these commands. The outputs in this document are examples only. |
In these examples, the eight serial interfaces (0 to 7) are on a port adapter in port adapter slot 0 of a Catalyst RSM/VIP2; also, most of the status information for each interface is omitted. (Interfaces are administratively shut down until you enable them.)
Router# show interfaces ethernet 0/0 Ethernet0/0 is administratively down, line protocol is down Hardware is cyBus Ethernet, address is 0000.0ca5.2300 (bia 0000.0ca5.2389) MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) (display text omitted) Router# show interfaces ethernet 0/1 Ethernet0/1 is administratively down, line protocol is down Hardware is cyBus Ethernet, address is 0000.0ca5.2301 (bia 0000.0ca5.238a) MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) (display text omitted) Router# show interfaces ethernet 0/2 Ethernet0/2 is administratively down, line protocol is down Hardware is cyBus Ethernet, address is 0000.0ca5.2302 (bia 0000.0ca5.238b) MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) (display text omitted) Router# show interfaces ethernet 0/3 Ethernet0/3 is administratively down, line protocol is down Hardware is cyBus Ethernet, address is 0000.0ca5.2303 (bia 0000.0ca5.238c) MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) (display text omitted) Router# show interfaces ethernet 0/4 Ethernet0/4 is administratively down, line protocol is down Hardware is cyBus Ethernet, address is 0000.0ca5.2304 (bia 0000.0ca5.238d) MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) (display text omitted) Router# show interfaces ethernet 0/5 Ethernet0/5 is administratively down, line protocol is down Hardware is cyBus Ethernet, address is 0000.0ca5.2305 (bia 0000.0ca5.238e) MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) (display text omitted) Router# show interfaces ethernet 0/6 Ethernet0/6 is administratively down, line protocol is down Hardware is cyBus Ethernet, address is 0000.0ca5.2306 (bia 0000.0ca5.238f) MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) (display text omitted) Router# show interfaces ethernet 0/7 Ethernet0/7 is administratively down, line protocol is down Hardware is cyBus Ethernet, address is 0000.0ca5.2307 (bia 0000.0ca5.2391) MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec)
The following example of the show interfaces ethernet port-adapter/port command shows all of the information specific to the first PA-8E interface port (interface port 0) in port adapter slot 1:
Router# show interfaces ethernet 1/0
Ethernet1/0 is administratively down, line protocol is down
Hardware is cyBus Ethernet, address is 0000.0ca5.2309 (bia 0000.0ca5.2392)
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255
Encapsulation ARPA, loopback not set, keepalive set (10 sec)
ARP type: ARPA, ARP Timeout 4:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters 2:56:26
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 input packets with dribble condition detected
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets, 0 restarts
0 output buffer failures, 0 output buffers swapped out
Following is an example of the show interfaces command for Cisco 7200 series and Cisco uBR7200 series routers. In this example, the eight serial interfaces (0 to 7) are on a port adapter in port adapter slot 2; also, most of the status information for each interface is omitted. (Interfaces are administratively shut down until you enable them.)
Router# show interfaces ethernet 2/0 Ethernet2/0 is administratively down, line protocol is down Hardware is AmdP2 Ethernet, address is 10.0.0.0 10.255.255.255 (bia 0000.0ca5.2389) MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) (display text omitted) Router# show interfaces ethernet 2/1 Ethernet2/1 is administratively down, line protocol is down Hardware is AmdP2 Ethernet, address is 10.0.0.0 10.255.255.255 (bia 0000.0ca5.238a) MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) (display text omitted)Router# sh int e 2/2 Ethernet2/2 is administratively down, line protocol is down Hardware is AmdP2 Ethernet, address is 10.0.0.0 10.255.255.255 (bia 0000.0ca5.238b) MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) (display text omitted) Router# show interfaces ethernet 2/3 Ethernet2/3 is administratively down, line protocol is down Hardware is AmdP2 Ethernet, address is 10.0.0.0 10.255.255.255 (bia 0000.0ca5.238c) MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) (display text omitted) Router# show interfaces ethernet 2/4 Ethernet2/4 is administratively down, line protocol is down Hardware is AmdP2 Ethernet, address is 10.0.0.0 10.255.255.255 (bia 0000.0ca5.238d) MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) (display text omitted) Router# show interfaces ethernet 2/5 Ethernet2/5 is administratively down, line protocol is down Hardware is AmdP2 Ethernet, address is 10.0.0.0 10.255.255.255 (bia 0000.0ca5.238e) MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) (display text omitted) Router# show interfaces ethernet 2/6 Ethernet2/6 is administratively down, line protocol is down Hardware is AmdP2 Ethernet, address is 10.0.0.0 10.255.255.255 (bia 0000.0ca5.238f) MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) (display text omitted) Router# show interfaces ethernet 2/7 Ethernet2/7 is administratively down, line protocol is down Hardware is AmdP2 Ethernet, address is 10.0.0.0 10.255.255.255 (bia 0000.0ca5.2391) MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) (display text omitted]
The following example of the show interfaces ethernet slot/port command shows all of the information specific to the first 8E interface port (interface port 0) in port adapter slot 2:
Router# show interfaces ethernet 2/0
Ethernet2/0 is administratively down, line protocol is down
Hardware is AmdP2 Ethernet, address is 10.0.0.0 10.255.255.255 (bia 0000.0ca5.2392)
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255
Encapsulation ARPA, loopback not set, keepalive set (10 sec)
ARP type: ARPA, ARP Timeout 4:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters 2:56:26
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 input packets with dribble condition detected
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets, 0 restarts
0 output buffer failures, 0 output buffers swapped out
Router# show interfaces ethernet 3/0/0 Ethernet3/0/0 is administratively down, line protocol is down Hardware is cyBus Ethernet, address is 0000.0ca5.2300 (bia 0000.0ca5.2389) MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) (display text omitted) Router# show interfaces ethernet 3/0/1 Ethernet3/0/1 is administratively down, line protocol is down Hardware is cyBus Ethernet, address is 0000.0ca5.2301 (bia 0000.0ca5.238a) MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) (display text omitted) Router# show interfaces ethernet 3/0/2 Ethernet3/0/2 is administratively down, line protocol is down Hardware is cyBus Ethernet, address is 0000.0ca5.2302 (bia 0000.0ca5.238b) MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) (display text omitted) Router# show interfaces ethernet 3/0/3 Ethernet3/0/3 is administratively down, line protocol is down Hardware is cyBus Ethernet, address is 0000.0ca5.2303 (bia 0000.0ca5.238c) MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) (display text omitted) Router# show interfaces ethernet 3/0/4 Ethernet3/0/4 is administratively down, line protocol is down Hardware is cyBus Ethernet, address is 0000.0ca5.2304 (bia 0000.0ca5.238d) MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) (display text omitted) Router# show interfaces ethernet 3/0/5 Ethernet3/0/5 is administratively down, line protocol is down Hardware is cyBus Ethernet, address is 0000.0ca5.2305 (bia 0000.0ca5.238e) MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) (display text omitted) Router# show interfaces ethernet 3/0/6 Ethernet3/0/6 is administratively down, line protocol is down Hardware is cyBus Ethernet, address is 0000.0ca5.2306 (bia 0000.0ca5.238f) MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) (display text omitted) Router# show interfaces ethernet 3/0/7 Ethernet3/0/7 is administratively down, line protocol is down Hardware is cyBus Ethernet, address is 0000.0ca5.2307 (bia 0000.0ca5.2391) MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec)
The following example of the show interfaces ethernet slot/port-adapter/port command shows all of the information specific to the first PA-8E interface port (interface port 0) in chassis slot 3, port adapter slot 1:
Router# show interfaces ethernet 3/1/0
Ethernet3/1/0 is administratively down, line protocol is down
Hardware is cyBus Ethernet, address is 0000.0ca5.2309 (bia 0000.0ca5.2392)
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255
Encapsulation ARPA, loopback not set, keepalive set (10 sec)
ARP type: ARPA, ARP Timeout 4:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters 2:56:26
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 input packets with dribble condition detected
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets, 0 restarts
0 output buffer failures, 0 output buffers swapped out
Proceed to the next section, "Using the ping Command to Verify Network Connectivity," to check network connectivity of the PA-8E and switch or router.
Using the ping command, you can verify that an interface port is functioning properly. This section provides a brief description of this command. Refer to the publications listed in the "Related Documentation" section for detailed command descriptions and examples.
The ping command sends echo request packets out to a remote device at an IP address that you specify. After sending an echo request, the system waits a specified time for the remote device to reply. Each echo reply is displayed as an exclamation point (!) on the console terminal; each request that is not returned before the specified timeout is displayed as a period (.). A series of exclamation points (!!!!!) indicates a good connection; a series of periods (.....) or the messages [timed out] or [failed] indicate a bad connection.
Following is an example of a successful ping command to a remote server with the address 10.0.0.10:
Router# ping 10.0.0.10 <Return> Type escape sequence to abort. Sending 5, 100-byte ICMP Echoes to 10.0.0.10, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/15/64 ms Router#
If the connection fails, verify that you have the correct IP address for the destination and that the device is active (powered on), and repeat the ping command.
Posted: Thu Aug 31 08:04:26 PDT 2000
Copyright 1989-2000©Cisco Systems Inc.