|
|
To continue your PA-2H port adapter installation, you must configure the HSSI interfaces. The instructions that follow apply to all supported platforms. Minor differences between the platforms---with Cisco IOS software commands---are noted.
This chapter contains the following sections:
You modify the configuration of your router through the software command interpreter called the EXEC (also called enable mode). You must enter the privileged level of the EXEC command interpreter with the enable command before you can use the configure command to configure a new interface or change the existing configuration of an interface. The system prompts you for a password if one has been set.
The system prompt for the privileged level ends with a pound sign (#) instead of an angle bracket (>). At the console terminal, use the following procedure to enter the privileged level:
Router> enable
Password:
Step 2 Enter the password (the password is case sensitive). For security purposes, the password is not displayed.
When you enter the correct password, the system displays the privileged-level system prompt (#):
Router#
To configure the new interfaces, proceed to the "Configuring the Interfaces" section.
After you verify that the new PA-2H is installed correctly (the enabled LED goes on), use the privileged-level configure command to configure the new interfaces. Have the following information available:
If you installed a new PA-2H or if you want to change the configuration of an existing interface, you must enter configuration mode to configure the new interfaces. If you replaced a PA-2H that was previously configured, the system recognizes the new interfaces and brings each of them up in their existing configuration.
For a summary of the configuration options available and instructions for configuring interfaces on a PA-2H, refer to the appropriate configuration publications listed in the "Related Documentation" section.
You execute configuration commands from the privileged level of the EXEC command interpreter, which usually requires password access. Contact your system administrator, if necessary, to obtain password access. (See the "Using the EXEC Command Interpreter" section for an explanation of the privileged level of the EXEC.)
This section contains the following subsections:
Before you remove an interface that you will not replace, or replace port adapters, use the shutdown command to shut down (disable) the interfaces to prevent anomalies when you reinstall the new or reconfigured interface processor. When you shut down an interface, it is designated administratively down in the show command displays.
Follow these steps to shut down an interface:
Step 2 At the privileged-level prompt, enter configuration mode and specify that the console terminal is the source of the configuration subcommands, as follows:
Router# configure terminal Enter configuration commands, one per line. End with CNTL/Z Router(config)#
Step 3 Shut down interfaces by entering the interface hssi subcommand (followed by the interface address of the interface), and then enter the shutdown command. Table 4-1 shows the command syntax.
When you have finished, press Ctrl-Z-hold down the Control key while you press Z-or enter end or exit to exit configuration mode and return to the EXEC command interpreter.
| Platform | Command | Example |
|---|---|---|
Catalyst RSM/VIP2 in Catalyst 5000 family switches | interface, followed by the type (hssi) and slot/port (port-adapter-slot-number/ | The example is for interface 0 and interface 1 on a port adapter in port adapter slot 1. Router(config-if)# interface hssi 1/0 Router(config-if)# shutdown Router(config-if)# interface hssi 1/1 Router(config-if)# shutdown Ctrl-Z Router# |
Cisco 7120 series routers | interface, followed by the type (hssi) and slot/port (port-adapter-slot-number/ | The example is for interface 0 and interface 1 on a port adapter in port adapter slot 3. Router(config-if)# interface hssi 3/0 Router(config-if)# shutdown Router(config-if)# interface hssi 3/1 Router(config-if)# shutdown Ctrl-Z Router# |
Cisco 7140 series routers | interface, followed by the type (hssi) and slot/port (port-adapter-slot-number/ | The example is for interface 0 and interface 1 on a port adapter in port adapter slot 4. Router(config-if)# interface hssi 4/0 Router(config-if)# shutdown Router(config-if)# interface hssi 4/1 Router(config-if)# shutdown Ctrl-Z Router# |
Cisco 7200 series routers | interface, followed by the type (hssi) and slot/port (port-adapter-slot-number/ | The example is for interface 0 and interface 1 on a port adapter in port adapter slot 6. Router(config-if)# interface hssi 6/0 Router(config-if)# shutdown Router(config-if)# interface hssi 6/1 Router(config-if)# shutdown Ctrl-Z Router# |
Cisco uBR7223 router | interface, followed by the type (hssi) and slot/port (port-adapter-slot-number/ | The example is for interface 0 and interface 1 on a port adapter in port adapter slot 1. Router(config-if)# interface hssi 1/0 Router(config-if)# shutdown Router(config-if)# interface hssi 1/1 Router(config-if)# shutdown Ctrl-Z Router# |
Cisco uBR7246 and Cisco uBR7246 VXR routers | interface, followed by the type (hssi) and slot/port (port-adapter-slot-number/ | The example is for interface 0 and interface 1 on a port adapter in port adapter slot 2. Router(config-if)# interface hssi 2/0 Router(config-if)# shutdown Router(config-if)# interface hssi 2/1 Router(config-if)# shutdown Ctrl-Z Router# |
VIP2 or VIP4 in Cisco 7000 series or Cisco 7500 series routers | interface, followed by the type (hssi) and slot/port-adapter/port (interface-processor-slot-number | The example is for interface 1 and interface 0 on a port adapter in port adapter slot 1 of a VIP2 installed Router(config-if)# interface hssi 1/1/1 Router(config-if)# shutdown Router(config-if)# interface hssi 1/1/0 Router(config-if)# shutdown Ctrl-Z Router# |
 |
Note If you need to shut down additional interfaces, enter the interface hssi command (followed by the interface address of the interface) for each of the interfaces on your port adapter. Use the no shutdown command to enable the interface. |
Step 4 Write the new configuration to NVRAM as follows:
Router# copy running-config startup-config [OK] Router#
The system displays an OK message when the configuration has been stored in NVRAM.
Step 5 Verify that the new interfaces are now in the correct state (shut down) using the show interfaces command (followed by the interface type and interface address of the interface) to display the specific interface. Table 4-2 provides examples.
| Platform | Command | Example |
|---|---|---|
Catalyst RSM/VIP2 in Catalyst 5000 family switches | show interfaces hssi, followed by slot/port | The example is for interface 0 on a PA-2H in port adapter slot 1. Router(config)# show interfaces hssi 1/0 Router(config-if)# |
Cisco 7120 series router | show interfaces hssi, followed by slot/port | The example is for interface 0 on a PA-2H in port adapter slot 3. Router(config)# show interfaces hssi 3/0 Router(config-if)# |
Cisco 7140 series router | show interfaces hssi, followed by slot/port | The example is for interface 0 on a PA-2H in port adapter slot 4. Router(config)# show interfaces hssi 4/0 Router(config-if)# |
Cisco 7200 series routers | show interfaces hssi, followed by slot/port (port-adapter-slot-number/ | The example is for interface 0 on a PA-2H in port adapter slot 6. Router(config)# show interfaces hssi 6/0 Router(config-if)# |
Cisco uBR7223 router | show interfaces hssi, followed by slot/port (port-adapter-slot- number/ | The example is for interface 0 on a PA-2H in port adapter slot 1. Router(config)# show interfaces hssi 1/0 Router(config-if)# |
Cisco uBR7246 and Cisco uBR7246 VXR routers | show interfaces hssi, followed by slot/port (port-adapter-slot-number/ | The example is for interface 0 on a PA-2H in port adapter slot 2. Router(config)# show interfaces hssi 2/0 Router(config-if)# |
VIP2 or VIP4 in Cisco 7000 series or Cisco 7500 series routers | show interfaces hssi, followed by slot/port-adapter/port (interface-processor-slot-number/ | The example is for interface 0 on a PA-2H in port adapter slot 1 of a VIP2 or VIP4 in interface processor slot 1. Router(config)# show interfaces hssi 1/1/0 Router(config-if)# |
Step 6 Reenable the interfaces by doing the following:
a. Repeat Step 3 to reenable an interface. Substitute the no shutdown command for the shutdown command.
b. Repeat Step 4 to write the new configuration to memory.
Use the copy running-config startup-config
c. Repeat Step 5 to verify that the interfaces are in the correct state. Use the show interfaces command followed by the interface type and interface address of the interface.
For complete descriptions of software configuration commands, refer to the publications listed in the "Related Documentation" section.
Following are instructions for a basic configuration: enabling an interface and specifying IP routing. You might also need to enter other configuration subcommands, depending on the requirements for your system configuration and the protocols you plan to route on the interface. For complete descriptions of configuration subcommands and the configuration options available for hssi interfaces, refer to the appropriate software documentation.
In the following procedure, press the Return key after each step unless otherwise noted. At any time you can exit the privileged level and return to the user level by entering disable at the prompt as follows:
Router# disable Router>
Router# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)#
Step 2 Specify the interface to configure by entering the interface hssi subcommand, followed by the interface address of the interface you plan to configure. Table 4-3 provides examples.
| Platform | Command | Example |
|---|---|---|
Catalyst RSM/VIP2 in Catalyst 5000 family switches | interface hssi, followed by slot/port (port-adapter-slot-number/ | The example is for interface 0 on a PA-2H in port adapter slot 1. Router(config)# interface hssi 1/0 Router(config-if)# |
Cisco 7120 series router | interface hssi, followed by slot/port (port-adapter-slot-number/ | The example is for interface 0 on a PA-2H in port adapter slot 3. Router(config)# interface hssi 3/0 Router(config-if)# |
Cisco 7140 series router | interface hssi, followed by slot/port (port-adapter-slot-number/ | The example is for interface 0 on a PA-2H in port adapter slot 4. Router(config)# interface hssi 4/0 Router(config-if)# |
Cisco 7200 series routers | interface hssi, followed by slot/port (port-adapter-slot-number/ | The example is for interface 0 on a PA-2H in port adapter slot 6. Router(config)# interface hssi 6/0 Router(config-if)# |
Cisco uBR7223 router | interface hssi, followed by slot/port (port-adapter-slot-number/ | The example is for interface 0 on a PA-2H in port adapter slot 1. Router(config)# interface hssi 1/0 Router(config-if)# |
Cisco uBR7246 and Cisco uBR7246 VXR routers | interface hssi, followed by slot/port (port-adapter-slot-number/ | The example is for interface 0 on a PA-2H in port adapter slot 2. Router(config)# interface hssi 2/0 Router(config-if)# |
VIP2 or VIP4 in Cisco 7000 series or Cisco 7500 series routers | interface hssi, followed by slot/port-adapter/port (interface-processor-slot-number/ | The example is for interface 0 on a PA-2H in port adapter slot 1 of a VIP2 or VIP4 in interface processor slot 1. Router(config)# interface hssi 1/1/0 Router(config-if)# |
Step 3 Assign an IP address and subnet mask to the interface (if IP routing is enabled on the system) by using the ip address subcommand, as in the following example:
Router(config-if)# ip address 10.0.0.0 10.255.255.255
Step 4 Add any additional configuration subcommands required to enable routing protocols and set the interface characteristics.
Step 5 Reenable the interfaces using the no shutdown command. (See the "Shutting Down an Interface" section.)
Step 6 Configure all additional port adapter interfaces as required.
Step 7 After including all of the configuration subcommands to complete your configuration, press Ctrl-Z-hold down the Control key while you press Z-or enter end or exit to exit configuration mode and return to the EXEC command interpreter prompt.
Step 8 Write the new configuration to NVRAM as follows:
Router# copy running-config startup-config [OK] Router#
This completes the procedure for creating a basic configuration.
Table 4-4 summarizes cyclic redundancy check (CRC) commands. For more information, see the remainder of this section.
| Purpose | Command | Example | Further Information |
|---|---|---|---|
Enable 32-bit CRC. | crc size | The example enables 32-bit CRC on a serial interface: Router(config)# interface hssi 3/0 Router(config-if)# crc 32 | |
Return to default 16-bit CRC. | no crc size | The example disables 32-bit CRC on a serial interface and returns to the default 16-bit CRC: Router(config)# interface hssi 3/0 Router(config-if)# no crc 32 |
CRC is an error-checking technique that uses a calculated numeric value to detect errors in transmitted data. All interfaces use a 16-bit CRC (CRC-CITT) by default but also support a 32-bit CRC. The sender of a data frame calculates the frame check sequence (FCS). Before it sends the frame, the sender appends the FCS value to the message. The receiver recalculates the FCS and compares its calculation to the FCS from the sender. If there is a difference between the two calculation, the receiver assumes that a transmission error occurred and sends a request to the sender to resend the frame.
Enable 32-bit CRC using the crc32 command. Before you can enable 32-bit CRC, you must use the interface hssi command (followed by the interface address of the interface) to select the interface on which you want to enable 32-bit CRC. This command functions in the same way on all supported platforms.
In the example that follows, 32-bit CRC is specified:
Router(config-if)# crc 32
The preceding command example applies to all systems in which the PA-2H is supported. Use the no crc 32 command to disable CRC-32 and return the interface to the default CRC-16 (CRC-CITT) setting.
When you have finished, press Ctrl-Z-hold down the Control key while you press Z-or enter end or exit to exit configuration mode and return to the EXEC command interpreter prompt. Then write the new configuration to NVRAM using the copy running-config startup-config command.
For complete descriptions, refer to the Configuration Fundamentals Configuration Guide publication. For more information, see the "Obtaining Documentation" section and the "Documentation CD-ROM" section.
|
Note When enabling a 32-bit CRC on an interface, ensure that the remote device is also configured for a 32-bit CRC. Both the sender and the receiver must use the same CRC setting. |
After configuring the new interface, use the show commands to display the status of the new interface or all interfaces, and use the ping and loopback commands to check connectivity. This section includes the following subsections:
Table 4-5 demonstrates how you can use the show commands to verify that new interfaces are configured and operating correctly and that the PA-2H appears in them correctly. Sample displays of the output of selected show commands appear in the sections that follow. For complete command descriptions and examples, refer to the publications listed in the "Related Documentation" section.
|
Note The outputs that appear in this document may not match the output you receive when running these commands. The outputs in this document are examples only. |
| Command | Function | Example | ||
|---|---|---|---|---|
show version or | Displays system hardware configuration, the number of each interface type installed, Cisco IOS software version, names and sources of configuration files, and boot images | Router# show version | ||
show controllers | Displays all the current interface processors and their interfaces | Router# show controllers | ||
show diag slot
| Displays types of port adapters installed in your system and information about a specific port adapter slot, interface processor slot, or chassis slot | Router# show diag 2 | ||
show interfaces hssi 0 or 1/ | Displays status information about a specific interface on a PA-2H in a Catalyst RSM/VIP2 | Router# show interfaces hssi 1/0 | ||
show interfaces hssi 3/interface-port-number | Displays status information about a specific interface on a PA-2H in a Cisco 7120 series router | Router# show interfaces hssi 3/1 | ||
show interfaces hssi 4/interface-port-number | Displays status information about a specific interface on a PA-2H in a Cisco 7140 series router | Router# show interfaces hssi 4/1 | ||
show interfaces hssi port-adapter-slot-number/ | Displays status information about a specific interface on a PA-2H in a Cisco 7200 series router | Router# show interfaces hssi 1/0 | ||
show interfaces hssi 1/interface-port-number | Displays status information about a specific interface on a PA-2H in a Cisco uBR7223 router | Router# show interfaces hssi 1/1 | ||
show interfaces hssi 1 or 2/ | Displays status information about a specific interface on a PA-2H in a Cisco uBR7246 or Cisco uBR7246 VXR routers | Router# show interfaces hssi 2/0 | ||
show interfaces hssi interface-processor- | Displays status information about a specific interface on a PA-2H on a VIP2 or VIP4 in a Cisco 7000 series or Cisco 7500 series router | Router# show interfaces hssi 3/1/0 | ||
show protocols | Displays protocols configured for the entire system and for specific interfaces | Router# show protocols | ||
show running-config | Displays the running configuration file | Router# show running-config | ||
show startup-config | Displays the configuration stored in NVRAM | Router# show startup-config |
If an interface is shut down and you configured it as up, or if the displays indicate that the hardware is not functioning properly, ensure that the interface is properly connected and terminated. If you still have problems bringing up the interface, contact a service representative for assistance. This section includes the following subsections:
Choose the subsection appropriate for your system. Proceed to the "Using the ping Command to Verify Network Connectivity" section when you have finished using the show commands.
Display the configuration of the system hardware, the number of each interface type installed, the Cisco IOS software version, the names and sources of configuration files, and the boot images, using the show version (or show hardware) command.
|
Note The outputs that appear in this document may not match the output you receive when running these commands. The outputs in this document are examples only. |
 |
Caution If you are using the PA-2H in the Catalyst 5000, 5500, 5505, or 5509 switch, you must install the port adapter on the Catalyst RSM/VIP2-15 or -40 Revision 2 (Part Number 73-3468-XX, where XX is the version number). Do not use the PA-2H in the Catalyst 5000, 5505, or 5509 switch if you are installing it on a Catalyst RSM/VIP2-15 or -40 that is not Revision 2. If you fail to comply with this restriction, your system will shut down because of an overload of the power supply. |
|
Caution You can only have two PA-2H port adapters per chassis when they are installed on a Catalyst RSM/VIP2-15 or -40 module Revision 1 and used in the Catalyst 5500 switch. |
Following is an example of the show version command from a Catalyst 5000 family switch with the PA-2H:
Switch# show version Cisco Internetwork Operating System Software IOS (tm) GS Software (C5RSM-JV-MZ), Released Version 11.2(15)A Copyright (c) 1986-1995 by cisco Systems, Inc. Compiled Fri 06-Oct-95 12:22 by mpo Image text-base: 0x600088A0, data-base: 0x605A4000 ROM: System Bootstrap, Version 5.3(5) ROM: GS Bootstrap Software (RSP-BOOT-M), Version 11.1(12), RELEASED SOFTWARE Switch uptime is 4 hours, 22 minutes System restarted by reload System image file is "slot0:c5rsm-jv-mz", booted via slot0 cisco RSP2 (R4700) processor with 16384K bytes of memory. R4600 processor, Implementation 32, Revision 2.0 Last reset from power-on G.703/E1 software, Version 1.0. Bridging software. X.25 software, Version 2.0, NET2, BFE and GOSIP compliant. Chassis Interface. 1 VIP2 controllers (2 HSSI). 2 HSSI network interfaces. 125K bytes of non-volatile configuration memory. 20480K bytes of Flash PCMCIA card at slot 0 (Sector size 128K). 8192K bytes of Flash internal SIMM (Sector size 256K). Configuration register is 0x2
Following is an example of the show version command from a Cisco 7200 series router with a PA-2H:
Router# show version Cisco Internetwork Operating System Software IOS (tm) 7200 Software (C7200-J-M), Released Version 12.0(3)T Copyright (c) 1986-1996 by cisco Systems, Inc. Compiled Fri 09-Aug-96 21:14 by biff Image text-base: 0x60010890, data-base: 0x605F0000 ROM: System Bootstrap, Version 12.0(3), RELEASED SOFTWARE ROM: 7200 Software (C7200-J-M), Version 12.0(3), RELEASED SOFTWARE Router uptime is 23 hours System restarted by reload System image file is "c7200-j-mz", booted via tftp from 10.0.0.10 cisco 7200 (R4700) processor with 22528K/10240K bytes of memory. R4700 processor, Implementation 33, Revision 1.0 (Level 2 Cache) Last reset from power-on Bridging software. SuperLAT software copyright 1990 by Meridian Technology Corp). X.25 software, Version 2.0, NET2, BFE and GOSIP compliant. TN3270 Emulation software (copyright 1994 by TGV Inc). (additional display text omitted from this example) 2 HSSI network interfaces. 125K bytes of non-volatile configuration memory. 8192K bytes of Flash internal SIMM (Sector size 256K). Configuration register is 0x0
Following is an example of the show version command from a Cisco 7000 series router with a PA-2H:
Router# show version Cisco Internetwork Operating System Software IOS (tm) GS Software (RSP-JV-MZ), Released Version 11.1(12)CA Copyright (c) 1986-1995 by cisco Systems, Inc. Compiled Mon 10-May-99 12:22 by biff Image text-base: 0x600088A0, data-base: 0x605A4000 ROM: System Bootstrap, Version 5.3(5) ROM: GS Bootstrap Software (RSP-BOOT-M), Version 11.1(12), RELEASED SOFTWARE Router uptime is 4 hours, 22 minutes System restarted by reload System image file is "slot0:rsp-jv-mz", booted via slot0 cisco RSP7000 (R4600) processor with 16384K bytes of memory. R4600 processor, Implementation 32, Revision 2.0 Last reset from power-on G.703/E1 software, Version 1.0. Bridging software. X.25 software, Version 2.0, NET2, BFE and GOSIP compliant. Chassis Interface. 1 VIP2 controllers (2 HSSI). 2 HSSI network interfaces. 125K bytes of non-volatile configuration memory. 20480K bytes of Flash PCMCIA card at slot 0 (Sector size 128K). 8192K bytes of Flash internal SIMM (Sector size 256K). Configuration register is 0x2
Display the types of port adapters installed in your system (and specific information about each) using the show diag slot command, where slot is the port adapter slot in a Cisco 7100 series, Cisco 7200 series and Cisco uBR7200 series router and the interface processor slot in a Cisco 7000 series or Cisco 7500 series router with a VIP2 or VIP4. (The slot argument is not required with Catalyst 5000 family switches and the Catalyst RSM/VIP.)
|
Note The outputs that appear in this document may not match the output you receive when running these commands. The outputs in this document are examples only. |
Following is an example of the show diag command that shows a PA-2H in a Catalyst 5000 family switch:
Switch# show diag
Slot 0:
HSSI-B port adapter, 1 port
Port adapter is analyzed
Port adapter insertion time 2d13h ago
Hardware revision 1.17 Board revision A0
Serial number 12345678 Part number 73-1801-05
Test history 0x0 RMA number 00-00-00
EEPROM format version 1
EEPROM contents (hex):
0x20:01 74 01 11 00 44 F1 94 49 07 09 05 00 00 00 00
0x30:50 00 00 00 97 04 21 00 FF FF FF FF FF FF FF FF
Slot database information:
Flags: 0x4 Insertion time: 0x14E8 (3d00h ago)
VIP Controller Memory Size: Unknown
PA Bay 0 Information:
HSSI-B PA, 1 ports
EEPROM format version 1
HW rev 1.3, Board revision A0
Serial number: 04551053 Part number: 73-2914-01
Following is an example of the show diag slot command that shows a PA-2H in port adapter slot 2 of a Cisco 7200 series router:
Router# show diag 2
Slot 2:
HSSI-B port adapter, 2 ports
Port adapter is analyzed
Port adapter insertion time 2d13h ago
Hardware revision 1.3 Board revision A0
Serial number 12345678 Part number 73-2914-01
Test history 0x0 RMA number 00-00-00
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 74 01 01 00 44 F1 94 49 07 09 05 00 00 00 00
0x30: 50 00 00 00 97 04 21 00 FF FF FF FF FF FF FF FF
|
Note Port adapters used with the Cisco 7200 VXR and Cisco uBR7246 VXR routers require the correct base hardware revision in order to function. The following error message will occur on bootup if the incorrect hardware revision is used: PA-3-REVNOTSUPPORTED:PA in slot 1 (Mx HSSI-B) requires base h/w revision of (1.3) for this chassisUse the show diag command to display the hardware revision. |
Following is an example of the show diag slot command for a PA-2H on a VIP4 in interface processor slot 8 of a Cisco 7500 series router:
Router# show diag 8
Slot 8:
Physical slot 8, ~physical slot 0x7, logical slot 8, CBus 0
Microcode Status 0x4
Master Enable, LED, WCS Loaded
Board is analyzed
Pending I/O Status:None
EEPROM format version 2
VIP4 RM7000 controller, HW rev 2.01, board revision A0
Serial number:12345678 Part number:211-18700-71
Test history:0x02 RMA number:00-00-00
Flags: unknown flags 0x7F; 7500 compatible
EEPROM contents (hex):
0x20:02 22 02 01 00 AF 7B C9 D3 49 0C 47 02 00 00 00
0x30:02 3A 0C FF FF FF FF FF FF FF FF FF FF FF FF FF
Slot database information:
Flags:0x4 Insertion time:0x3EC4FE0 (00:02:08 ago)
Controller Memory Size:64 MBytes DRAM, 65536 KBytes SRAM
PA Bay 0 Information:
Mx HSSI PA, 2 ports
EEPROM format version 1
HW rev 1.03, Board revision A0
Serial number:12345678 Part number:73-2914-02
|
Note The syntax for the show interfaces command is given in Table 4-2 for all supported platforms. |
For complete descriptions of interface subcommands and the configuration options available for Catalyst RSM/VIP2, Cisco 7100 series, Cisco 7200 series, Cisco uBR7200 series, and VIP2 and VIP4 interfaces, refer to the publications listed in the "Related Documentation" section.
|
Note The outputs that appear in this document may not match the output you receive when running these commands. The outputs in this document are examples only. |
Following is an example of the show interfaces hssi command for a PA-2H in a Catalyst 5000 family switch:
Switch# show interfaces hssi 0/0
Hssi0/0 is up, line protocol is up
Hardware is HSSI-B
Internet address is 10.1.1.10
MTU 4470 bytes, BW 45045 Kbit, DLY 200 usec, rely 255/255, load 1/255
Encapsulation HDLC, loopback not set, keepalive not set
Last input 2d22h, output 00:00:19, output hang never
Last clearing of "show interface" counters 2d20h
Queueing strategy: fifo
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 parity
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
4084 packets output, 1298712 bytes, 0 underruns
0 output errors, 0 applique, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
Following is an example of the show interfaces hssi command for a PA-2H in a Cisco 7200 series router:
Router# show interfaces hssi 2/0
Hssi2/0 is up, line protocol is up
Hardware is HSSI-B
Internet address is 10.1.1.10
MTU 4470 bytes, BW 45045 Kbit, DLY 200 usec, rely 252/255, load 1/255
Encapsulation HDLC, loopback not set, keepalive not set
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Queueing strategy: fifo
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
0 parity
0 input errors, 1 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
1 packets output, 24 bytes, 0 underruns
0 output errors, 0 applique, 1 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions TM=down CA=up LC=down
|
Note For the Cisco 7206 and Cisco 7206VXR router shelves, the show interfaces command requires a shelf number in the format show interfaces type shelf number/port adapter slot/interface. |
Following is an example of the show interfaces hssi command for a PA-2H in a Cisco 7000 series or Cisco 7500 series router:
Router# show interfaces hssi 1/0/0
Hssi1/0/0 is up, line protocol is up
Hardware is HSSI-B
Internet address is 10.1.1.10
MTU 4470 bytes, BW 45045 Kbit, DLY 200 usec, rely 255/255, load 1/255
Encapsulation HDLC, loopback not set, keepalive not set
Last input 2d22h, output 00:00:19, output hang never
Last clearing of "show interface" counters 2d20h
Queueing strategy: fifo
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 parity
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
4084 packets output, 1298712 bytes, 0 underruns
0 output errors, 0 applique, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
Using the ping command, you can verify that an interface port is functioning properly. This section provides a brief description of this command. Refer to the publications listed in the "Related Documentation" section for detailed command descriptions and examples.
The ping command sends echo request packets out to a remote device at an IP address that you specify. After sending an echo request, the system waits a specified time for the remote device to reply. Each echo reply is displayed as an exclamation point (!) on the console terminal; each request that is not returned before the specified timeout is displayed as a period (.). A series of exclamation points (!!!!!) indicates a good connection; a series of periods (.....) or the messages [timed out] or [failed] indicate a bad connection.
Following is an example of a successful ping command to a remote server with the IP address 10.0.0.10:
Router# ping 10.0.0.10 <Return> Type escape sequence to abort. Sending 5, 100-byte ICMP Echoes to 10.0.0.10, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/15/64 ms Router#
If the connection fails, verify that you have the correct IP address for the destination and that the device is active (powered on), and repeat the ping command.
This completes the PA-2H interface configuration.
Posted: Thu Apr 27 20:56:19 PDT 2000
Copyright 1989 - 2000©Cisco Systems Inc.