|
|
To continue your PA-5EFL port adapter installation, you must configure the Ethernet interfaces. The instructions that follow apply to all supported platforms. Minor differences between the platforms---with Cisco IOS software commands---are noted.
This chapter contains the following sections:
You modify the configuration of your router through the software command interpreter called the EXEC (also called enable mode). You must enter the privileged level of the EXEC command interpreter with the enable command before you can use the configure command to configure a new interface or change the existing configuration of an interface. The system prompts you for a password if one has been set.
The system prompt for the privileged level ends with a pound sign (#) instead of an angle bracket (>). At the console terminal, use the following procedure to enter the privileged level:
Router> enable
Password:
Step 2 Enter the password (the password is case sensitive). For security purposes, the password is not displayed.
When you enter the correct password, the system displays the privileged-level system prompt (#):
Router#
To configure the new interfaces, proceed to the "Configuring the Interfaces" section.
After you verify that the new PA-5EFL is installed correctly (the enabled LED goes on), use the privileged-level configure command to configure the new interfaces. Have the following information available:
If you installed a new PA-5EFL or if you want to change the configuration of an existing interface, you must enter configuration mode to configure the new interfaces. If you replaced a PA-5EFL that was previously configured, the system recognizes the new interfaces and brings each of them up in their existing configuration.
For a summary of the configuration options available and instructions for configuring interfaces on a PA-5EFL, refer to the appropriate configuration publications listed in the "Related Documentation" section.
You execute configuration commands from the privileged level of the EXEC command interpreter, which usually requires password access. Contact your system administrator, if necessary, to obtain password access. (See the "Using the EXEC Command Interpreter" section for an explanation of the privileged level of the EXEC.)
This section contains the following subsections:
Before you remove an interface that you will not replace, or replace port adapters, use the shutdown command to shut down (disable) the interfaces to prevent anomalies when you reinstall the new or reconfigured interface processor. When you shut down an interface, it is designated administratively down in the show command displays.
Follow these steps to shut down an interface:
Step 2 At the privileged-level prompt, enter configuration mode and specify that the console terminal is the source of the configuration subcommands, as follows:
Router# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)#
Step 3 Shut down interfaces by entering the interface ethernet subcommand (followed by the interface address of the interface) and then enter the shutdown command. Table 4-1 shows the command syntax.
When you have finished, press Ctrl-Z---hold down the Control key while you press Z---or enter end or exit to exit configuration mode and return to the EXEC command interpreter.
| Platform | Command | Example |
|---|---|---|
Cisco 7120 series routers | interface, followed by the type (ethernet) and slot/port (port-adapter-slot-number/ interface-port-number) | The example is for interface 0 and interface 1 on a port adapter in port adapter slot 3. Router(config-if)# interface ethernet 3/0 Router(config-if)# shutdown Router(config-if)# interface ethernet 3/1 Router(config-if)# shutdown Ctrl-Z Router# |
Cisco 7140 series routers | interface, followed by the type (ethernet) and slot/port (port-adapter-slot-number/ interface-port-number) | The example is for interface 0 and interface 1 on a port adapter in port adapter slot 4. Router(config-if)# interface ethernet 4/0 Router(config-if)# shutdown Router(config-if)# interface ethernet 4/1 Router(config-if)# shutdown Ctrl-Z Router# |
Cisco 7200 series routers | interface, followed by the type (ethernet) and slot/port (port-adapter-slot-number/ interface-port-number) | The example is for interface 0 and interface 1 on a port adapter in port adapter slot 6. Router(config-if)# interface ethernet 6/0 Router(config-if)# shutdown Router(config-if)# interface ethernet 6/1 Router(config-if)# shutdown Ctrl-Z Router# |
Cisco uBR7223 router | interface, followed by the type (ethernet) and slot/port (port-adapter-slot-number/ interface-port-number) | The example is for interface 0 and interface 1 on a port adapter in port adapter slot 1. Router(config-if)# interface ethernet 1/0 Router(config-if)# shutdown Router(config-if)# interface ethernet 1/1 Router(config-if)# shutdown Ctrl-Z Router# |
Cisco uBR7246 router | interface, followed by the type (ethernet) and slot/port (port-adapter-slot-number/ interface-port-number) | The example is for interface 0 and interface 1 on a port adapter in port adapter slot 2. Router(config-if)# interface ethernet 2/0 Router(config-if)# shutdown Router(config-if)# interface ethernet 2/1 Router(config-if)# shutdown Ctrl-Z Router# |
VIP2 in Cisco 7000 series or | interface, followed by the type (ethernet) and slot/port adapter/port (interface-processor-slot-number/ port-adapter-slot-number/ interface-port-number) | The example is for interface 0 and interface 1 on a port adapter in port adapter slot 1 of a VIP2 installed in interface processor slot 1. Router(config-if)# interface ethernet 1/1/0 Router(config-if)# shutdown Router(config-if)# interface ethernet 1/1/0 Router(config-if)# shutdown Ctrl-Z Router# |
 |
Note If you need to shut down additional interfaces, enter the interface ethernet command (followed by the interface address of the interface) for each of the interfaces on your port adapter. Use the no shutdown command to enable the interface. |
Step 4 Write the new configuration to NVRAM as follows:
Router# copy running-config startup-config [OK] Router#
The system displays an OK message when the configuration has been stored in NVRAM.
Step 5 Verify that new interfaces are now in the correct state (shut down) using the
show interfaces ethernet command (followed by the interface address of the interface) to display the specific interface. Table 4-2 provides examples.
| Platform | Command | Example |
|---|---|---|
Cisco 7120 series routers | show interfaces ethernet, followed by slot/port (port-adapter-slot-number/ interface-port-number)
| The example is for interface 0 on a port adapter in port adapter slot 1. Router# show interfaces ethernet 1/0 Serial 1/0 is administratively down, line protocol is down [Additional display text omitted from this example] |
Cisco 7140 | show interfaces ethernet, followed by slot/port (port-adapter-slot-number/ interface-port-number)
| The example is for interface 0 on a port adapter in port adapter slot 1. Router# show interfaces ethernet 1/0 Serial 1/0 is administratively down, line protocol is down [Additional display text omitted from this example] |
Cisco 7200 series | show interfaces ethernet, followed by slot/port (port-adapter-slot-number/ interface-port-number) | The example is for interface 0 on a port adapter in port adapter slot 6. Router# show interfaces ethernet 6/0 Serial 6/0 is administratively down, line protocol is down [Additional display text omitted from this example] |
Cisco uBB7223 router | show interfaces ethernet, followed by slot/port (port-adapter-slot-number/ interface-port-number)
| The example is for interface 0 on a port adapter in port adapter slot 1. Router# show interfaces ethernet 1/0 Serial 1/0 is administratively down, line protocol is down [Additional display text omitted from this example]
|
Cisco uBR7246 router | show interfaces ethernet, followed by slot/port (port-adapter-slot-number/ interface-port-number) | The example is for interface 0 on a port adapter in port adapter slot 2. Router# show interfaces ethernet 2/0 Serial 2/0 is administratively down, line protocol is down [Additional display text omitted from this example]
|
VIP2 in Cisco 7000 series or Cisco 7500 series routers | show interfaces ethernet, followed by slot/port adapter/port (interface-processor-slot-number/ port-adapter-slot-number/ interface-port-number) | The example is for interface 0 on a port adapter in port adapter slot 1 of a VIP2 in interface processor slot 1. Router# show interfaces ethernet 1/1/0 Ethernet 1/1/0 is administratively down, line protocol is down [Additional display text omitted from this example] |
Step 6 Reenable interfaces by doing the following:
a. Repeat Step 3 to reenable an interface. Substitute the no shutdown command for the shutdown command.
b. Repeat Step 4 to write the new configuration to memory.
Use the copy running-config startup-config command.
c. Repeat Step 5 to verify that the interfaces are in the correct state. Use the
show interfaces ethernet command followed by the interface address of the interface.
For complete descriptions of software configuration commands, refer to the publications listed in the "Related Documentation" section.
Following are instructions for a basic configuration: enabling an interface and specifying IP routing. You might also need to enter other configuration subcommands, depending on the requirements for your system configuration and the protocols you plan to route on the interface. For complete descriptions of configuration subcommands and the configuration options available for ethernet interfaces, refer to the appropriate software documentation.
In the following procedure, press the Return key after each step unless otherwise noted. At any time you can exit the privileged level and return to the user level by entering disable at the prompt as follows:
Router# disable Router>
Router# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)#
Step 2 Specify the first interface to configure by entering the interface ethernet subcommand, followed by the interface address of the interface you plan to configure. Table 4-3 gives examples.
| Platform | Command | Example |
|---|---|---|
Cisco 7120 series routers | interface ethernet, followed by slot/port (port-adapter-slot-number/ interface-port-number) | The example is for the first interface of a port adapter in port adapter slot 3. Router(config)# interface ethernet 3/0 Router(config-if)# |
Cisco 7140 series routers | interface ethernet, followed by slot/port (port-adapter-slot-number/ interface-port-number) | The example is for the first interface of a port adapter in port adapter slot 4. Router(config)# interface ethernet 4/0 Router(config-if)# |
Cisco 7200 series routers | interface ethernet, followed by slot/port (port-adapter-slot-number/ interface-port-number) | The example is for the first interface of a port adapter in port adapter slot 1. Router(config)# interface ethernet 1/0 Router(config-if)# |
Cisco uBR7223 router | interface ethernet, followed by slot/port (port-adapter-slot-number/ interface-port-number) | The example is for the first interface of a port adapter in port adapter slot 1. Router(config)# interface ethernet 1/0 Router(config-if)# |
Cisco uBR7246 router | interface ethernet, followed by slot/port (port-adapter-slot-number/ interface-port-number) | The example is for the first interface of a port adapter in port adapter slot 2. Router(config)# interface ethernet 2/0 Router(config-if)# |
VIP2 in Cisco 7000 series or Cisco 7500 series routers | interface ethernet, followed by slot/port adapter/port (interface-processor-slot-number/ port-adapter-slot-number/ interface-port-number) | The example is for the first interface of a Router(config)# interface ethernet 1/1/0 Router(config-if)# |
Step 3 Assign an IP address and subnet mask to the interface (if IP routing is enabled on the system) by using the ip address subcommand, as in the following example:
Router(config-if)# ip address 10.0.0.0 10.255.255.255
Step 4 Add any additional configuration subcommands required to enable routing protocols and set the interface characteristics.
Step 5 Reenable the interfaces using the no shutdown command. (See the "Shutting Down an Interface" section.)
Step 6 Configure all additional port adapter interfaces as required.
Step 7 After including all of the configuration subcommands to complete your configuration, press Ctrl-Z---hold down the Control key while you press Z---or enter end or exit to exit configuration mode and return to the EXEC command interpreter prompt.
Step 8 Write the new configuration to NVRAM as follows:
Router# copy running-config startup-config [OK] Router#
This completes the procedure for creating a basic configuration.
After configuring the new interface, use the show commands to display the status of the new interface or all interfaces, and use the ping and loopback commands to check connectivity. This section includes the following subsections:
Table 4-4 demonstrates how you can use the show commands to verify that new interfaces are configured and operating correctly and that the PA-5EFL appears in them correctly. Sample displays of the output of selected show commands appear in the sections that follow. For complete command descriptions and examples, refer to the publications listed in the "Related Documentation" section.
|
Note The outputs that appear in this document may not match the output you receive when running these commands. The outputs in this document are examples only. |
| Command | Function | Example |
|---|---|---|
show version or | Displays system hardware configuration, the number of each interface type installed, Cisco IOS software version, names and sources of configuration files, and boot images | Router# show version |
show controllers | Displays all the current interface processors and their interfaces | Router# show controllers |
show diag slot | Displays types of port adapters installed in your system and information about a specific port adapter slot, interface processor slot, or chassis slot | Router# show diag 2 |
show interfaces type 3/ interface-port-number
| Displays status information about a specific type of interface (for example, ethernet) in a Cisco 7120 series router | Router# show interfaces ethernet 3/1 |
show interfaces type 4/
| Displays status information about a specific type of interface (for example, ethernet) in a Cisco 7140 series router | Router# show interfaces ethernet 4/1 |
show interfaces type port-adapter-slot-number/ | Displays status information about a specific type of interface (for example, ethernet) in a Cisco 7200 series router | Router# show interfaces ethernet 1/0 |
show interfaces type 1/ interface-port-number
| Displays status information about a specific type of interface (for example, ethernet) in a Cisco uBR7223 router | Router# show interfaces ethernet 1/1 |
show interfaces type 1 or 2/ | Displays status information about a specific type of interface (for example, ethernet) in a Cisco uBR7246 router | Router# show interfaces ethernet 2/0 |
show interfaces type interface-processor-slot-number/ port-adapter-slot-number/ | Displays status information about a specific type of interface (for example, ethernet) on a VIP2 in a Cisco 7000 series or Cisco 7500 series router | Router# show interfaces ethernet 3/1/0 |
show protocols | Displays protocols configured for the entire system and for specific interfaces | Router# show protocols |
show running-config | Displays the running configuration file | Router# show running-config |
show startup-config | Displays the configuration stored in NVRAM | Router# show startup-config |
If an interface is shut down and you configured it as up, or if the displays indicate that the hardware is not functioning properly, ensure that the interface is properly connected and terminated. If you still have problems bringing up the interface, contact a service representative for assistance. This section includes the following subsections:
Choose the subsection appropriate for your system. Proceed to the "Using the ping Command to Verify Network Connectivity" section when you have finished using the show commands.
Display the configuration of the system hardware, the number of each interface type installed, the Cisco IOS software version, the names and sources of configuration files, and the boot images, using the show version (or show hardware) command.
|
Note The outputs that appear in this document may not match the output you receive when running these commands. The outputs in this document are examples only. |
Cisco 7100 Series Routers
Following is an example of the show version command from a Cisco 7120 series router with the PA-5EFL:
Router# show version Cisco Internetwork Operating System Software IOS (tm) EGR Software (c7100-IS-M), Version 12.0(4)XE, EARLY DEPLOYMENT RELEASE) TAC:Home:SW:IOS:Specials for info Copyright (c) 1986-1999 by cisco Systems, Inc. Compiled Thu 10-Jun-99 15:32 by linda Image text-base:0x60008900, data-base:0x60D8E000 ROM:System Bootstrap, Version 12.0(19990720:023243) [gautham-conn_4xe-PRE_ALPHE BOOTFLASH:EGR Software (c7100-IS-M), Version 12.0(4)XE, EARLY DEPLOYMENT RELEA) Router uptime is 24 minutes System restarted by power-on System image file is "disk0:c7100-is-mz.120-4.XE" cisco 7120-bad (EGR) processor with 61440K/69632K bytes of memory. R527x CPU at 225Mhz, Implementation 40, Rev 10.0, 2048KB L2 Cache Last reset from power-on Bridging software. X.25 software, Version 3.0.0. 4 Ethernet/IEEE 802.3 interfaces. 125K bytes of non-volatile configuration memory. 40960K bytes of ATA PCMCIA card at slot 0 (Sector size 512 bytes). 8192K bytes of Flash internal SIMM (Sector size 256K). Configuration register is 0x2000
Cisco 7200 Series and Cisco uBR7200 Series Routers
Following is an example of the show version command from a Cisco 7200 series router with the PA-5EFL:
Router# show version Cisco Internetwork Operating System Software IOS (tm) 7200 Software (C7200-J-M), Version 11.1(7)CA [biff 105] Copyright (c) 1986-1996 by cisco Systems, Inc. Compiled Sun 04-Aug-96 06:00 by biff Image text-base: 0x600088A0, data-base: 0x605A4000 ROM: System Bootstrap, Version 11.1(7)CA RELEASED SOFTWARE Router uptime is 4 hours, 22 minutes System restarted by reload System image file is "c7200-j-mz", booted via slot0 cisco 7206 (NPE150) processor with 12288K/4096K bytes of memory. R4700 processor, Implementation 33, Revision 1.0 (Level 2 Cache) Last reset from power-on Bridging software. SuperLAT software (copyright 1990 by Meridian Technology Corp). X.25 software, Version 2.0, NET2, BFE and GOSIP compliant. TN3270 Emulation software (copyright 1994 by TGV INC). Chassis Interface. 4 Ethernet/IEEE 802.3 interfaces. 2 FastEthernet/IEEE 802.3 interfaces. 4 Token Ring /IEEE802.5 interfaces. 12 Serial network interfaces. 1 Compression port adapter. 125K bytes of non-volatile configuration memory. 1024K bytes of packet SRAM memory. 20480K bytes of Flash PCMCIA card at slot 0 (Sector size 128K). 8192K bytes of Flash internal SIMM (Sector size 256K). Configuration register is 0x2
VIP2 in Cisco 7000 Series and Cisco 7500 Series Routers
Following is an example of the show version command from a Cisco 7500 series router with the PA-5EFL:
Router# show version Cisco Internetwork Operating System Software IOS (tm) GS Software (RSP-A), Version 11.1(7)CA [biff 125] Copyright (c) 1986-1996 by cisco Systems, Inc. Compiled Sat 10-Aug-96 17:56 by biff Image text-base: 0x600108A0, data-base: 0x60952000 ROM: System Bootstrap, Version 5.3(16645) [biff 571], RELEASE SOFTWARE ROM: GS Software (RSP-BOOT-M), Version 11.1(7)CA, RELEASE SOFTWARE (fc1) Router uptime is 5 days, 4 minutes System restarted by reload System image file is "rsp-jv-mz", booted via slot0 cisco RSP2 (R4600) processor with 16384K bytes of memory. R4600 processor, Implementation 32, Revision 2.0 Last reset from power-on G.703/E1 software, Version 1.0. SuperLAT software (copyright 1990 by Meridian Technology Corp). Bridging software. X.25 software, Version 2.0, NET2, BFE and GOSIP compliant. TN3270 Emulation software (copyright 1994 by TGV Inc). Chassis Interface. 1 EIP controller (6 Ethernet). 1 VIP2 controller (8 Ethernet)(1 HSSI). 14 Ethernet/IEEE 802.3 interfaces. 1 HSSI network interface. 125K bytes of non-volatile configuration memory. 8192K bytes of Flash PCMCIA card at slot 0 (Sector size 128K). 8192K bytes of Flash internal SIMM (Sector size 256K). Configuration register is 0x0
Display the types of port adapters installed in your system (and specific information about each) using the show diag slot command, where slot is the port adapter slot in a Cisco 7200 series and Cisco uBR7200 series router and the interface processor slot in a Cisco 7000 series or Cisco 7500 series router with a VIP2.
|
Note The outputs that appear in this document may not match the output you receive when running these commands. The outputs in this document are examples only. |
Cisco 7100 Series Routers
Following is an example of the show diag slot command that shows a PA-5EFL in port-adapter slot 3 of a Cisco 7120 series router:
Router# show diag 3
Slot 3:
Ethernet port adapter, 5 ports
Integrated port adapter is analyzed
EEPROM contents at hardware discovery:
Hardware revision 255.255 Board revision UNKNOWN
EEPROM format version 1
EEPROM contents (hex):
0x20:01 D3 FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x30:FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
|
Note To use the show diag command with the Cisco 7140 series router, replace the slot argument 3 with 4. |
Cisco 7200 Series and Cisco uBR7200 Series Routers
Following is an example of the show diag slot command that shows a PA-5EFL in port adapter slot 2 of a Cisco 7200 series router:
Router# show diag 2 Slot 2: Ethernet port adapter, 5 ports Port adapter is analyzed Port adapter insertion time 2d09h ago Hardware revision 255.255 Board revision UNKNOWN Serial number 4294967295 Part number 255-65535-255 Test history 0xFF RMA number 255-255-255 EEPROM format version 1 EEPROM contents (hex): 0x20: 01 0D FF FF FF FF FF FF FF FF FF FF FF FF FF FF 0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
|
Note Port adapters used with the Cisco 7200 VXR routers require the correct base hardware revision in order to function. The following error message occurs on bootup if the incorrect hardware revision is used: > PA-3-REVNOTSUPPORTED:PA in slot 1 (Ethernet) requires base h/w revision of (1.5) for this chassisUse the show diag command to display the hardware revision. |
VIP2 in Cisco 7000 Series and Cisco 7500 Series Routers
Following is an example of the show diag slot command that shows a PA-5EFL in port adapter slot 0 on a VIP2 in interface processor slot 1:
Router# show diag 1
Slot 1:
Physical slot 1, ~physical slot 0xE, logical slot 1, CBus 0
Microcode Status 0xC
Master Enable, LED, WCS Loaded
Board is analyzed
Pending I/O Status: Console I/O
EEPROM format version 1
VIP2 controller, HW rev 2.2, board revision UNKNOWN
Serial number: 03508056 Part number: 73-1554-02
Test history: 0x00 RMA number: 43-27-00
Flags: cisco 7000 board; 7500 compatible
EEPROM contents (hex):
0x20: 01 15 02 02 00 35 87 58 49 06 12 02 00 2B 1B 00
0x30: 12 2B 00 2A 1A 00 00 00 00 00 00 00 00 00 00 00
Slot database information:
Flags: 0x4 Insertion time: 0x10DC (00:01:17 ago)
Controller Memory Size: 8 MBytes
PA Bay 1 Information:
Ethernet PA, 5 ports
EEPROM format version 1
HW rev 1.0, Board revision 6
Serial number: 03522225 Part number: 73-1679-01
The show interfaces command displays status information (including the physical slot and interface address) for the interfaces you specify. All of the examples that follow specify ethernet interface.
For complete descriptions of interface subcommands and the configuration options available for Cisco 7100, Cisco 7200, Cisco uBR7200 and VIP2 interfaces, refer to the publications listed in the "Related Documentation" section.
|
Note The outputs that appear in this document may not match the output you receive when running these commands. The outputs in this document are examples only. |
Cisco 7100 Series
Following is an example of the show interfaces command used with a Cisco 7120 series router and a Cisco 7140 series router.
In this example, the five ethernet interfaces (0 to 4) are on a port adapter in port adapter slot 3 of a
Cisco 7120 series router; also, most of the status information for each interface is omitted. (Interfaces are administratively shut down until you enable them.)
Router# show interfaces ethernet 3/0 Ethernet3/0 is up, line protocol is up Hardware is AmdP2 Ethernet Internet address is 10.0.0.0 MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec, rely 255/255, load 1/255 Encapsulation HDLC, loopback not set, keepalive set (10 sec) [Additional display text omitted from this example] Router# show interfaces ethernet 3/1 Ethernet3/1 is up, line protocol is up Hardware is AmdP2 Ethernet Internet address is 10.0.0.1 MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec, rely 255/255, load 1/255 Encapsulation HDLC, loopback not set, keepalive set (10 sec) [Additional display text omitted from this example] Router# show interfaces ethernet 3/2 Ethernet3/2 is up, line protocol is up Hardware is AmdP2 Ethernet Internet address is 10.0.0.2 MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec, rely 255/255, load 1/255 Encapsulation HDLC, loopback not set, keepalive set (10 sec) [Additional display text for remaining interfaces omitted] Router# show interfaces ethernet 3/3 Ethernet3/3 is up, line protocol is up Hardware is AmdP2 Ethernet Internet address is 10.0.0.3 MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec, rely 255/255, load 1/255 Encapsulation HDLC, loopback not set, keepalive set (10 sec) [Additional display text for remaining interfaces omitted] Router# show interfaces ethernet 3/4 Ethernet3/4 is up, line protocol is up Hardware is AmdP2 Ethernet Internet address is 10.0.0.4 MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec, rely 255/255, load 1/255 Encapsulation HDLC, loopback not set, keepalive set (10 sec) [Additional display text for remaining interfaces omitted]
|
Note To use the show interfaces ethernet command with the Cisco 7140 series router, replace the interface address arguments 3/0, 3/1, 3/2, 3/3, and 3/4 with 4/0, 4/1, 4/2, 4/3, and 4/4, respectively. |
Following is an example of the show interfaces ethernet command, which shows all of the information specific to interface 0 on a PA-5EFL installed in port adapter slot 3 of a Cisco 7120 series router:
Router# show interfaces ethernet 3/0
Ethernet3/0 is up, line protocol is up
Hardware is AmdP2 Ethernet
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec, rely 255/255, load 1/255
Encapsulation HDLC, loopback not set, keepalive set (10 sec)
Last input never, output 1d17h, output hang never
Last clearing of "show interface" counters never
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
24 packets output, 5137 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions DCD=down DSR=down DTR=down RTS=down CTS=down
|
Note To use the show interfaces ethernet command with the Cisco 7140 series router, replace the interface address argument 3/0 with 4/0. |
Cisco 7200 Series and Cisco uBR7200 Series Routers
Following is an example of the show interfaces command for Cisco 7200 series and Cisco uBR7200 series routers. In the example, the five ethernet interfaces (0 to 4) are on a port adapter in port adapter slot 2; also, most of the status information for each interface is omitted. (Interfaces are administratively shut down until you enable them.)
Router# show interfaces ethernet 2/0 Ethernet2/0 is administratively down, line protocol is down Hardware is AmdP2 Ethernet, address is 10.0.0.0 (bia 0000.0ca5.2389) MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) [Additional display text omitted from this example] Router# show interfaces ethernet 2/1 Ethernet2/1 is administratively down, line protocol is down Hardware is AmdP2 Ethernet, address is 10.0.0.1 (bia 0000.0ca5.238a) MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) [Additional display text omitted from this example] Router# show interfaces ethernet 2/2 Ethernet2/2 is administratively down, line protocol is down Hardware is AmdP2 Ethernet, address is 10.0.0.2 (bia 0000.0ca5.238b) MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) [Additional display text omitted from this example]
Router# show interfaces ethernet 2/3 Ethernet2/3 is administratively down, line protocol is down Hardware is AmdP2 Ethernet, address is 10.0.0.3 (bia 0000.0ca5.238c) MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) [Additional display text omitted from this example] Router# show interfaces ethernet 2/4 Ethernet2/4 is administratively down, line protocol is down Hardware is AmdP2 Ethernet, address is 10.0.0.4 (bia 0000.0ca5.238d) MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) [Additional display text omitted from this example]
Following is an example of the show interfaces ethernet command, which shows all of the information specific to interface port 0 on a PA-5EFL installed in port adapter slot 2:
Router# show interfaces ethernet 2/0
Ethernet2/0 is administratively down, line protocol is down
Hardware is AmdP2 Ethernet, address is 10.0.0.0 (bia 0000.0ca5.238e)
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255
Encapsulation ARPA, loopback not set, keepalive set (10 sec)
ARP type: ARPA, ARP Timeout 4:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters 2:56:26
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 input packets with dribble condition detected
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets, 0 restarts
0 output buffer failures, 0 output buffers swapped out
VIP2 in Cisco 7000 Series or Cisco 7500 Series Routers
Following is an example of the show interfaces command used with the VIP2. In this example, the five ethernet interfaces (0 to 4) are on a port adapter port adapter slot 0 of a VIP2 in interface processor slot 3; also, most of the status information for each interface is omitted. (Interfaces are administratively shut down until you enable them.)
Router# show interfaces ethernet 3/0/0 Ethernet3/0/1 is administratively down, line protocol is down Hardware is cyBus Ethernet, address is 0000.0ca5.2300 (bia 0000.0ca5.2389) MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) [Additional display text omitted from this example] Router# show interfaces ethernet 3/0/1 Ethernet3/0/2 is administratively down, line protocol is down Hardware is cyBus Ethernet, address is 0000.0ca5.2301 (bia 0000.0ca5.238a) MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) [Additional display text omitted from this example] Router# show interfaces ethernet 3/0/2 Ethernet3/0/3 is administratively down, line protocol is down Hardware is cyBus Ethernet, address is 0000.0ca5.2302 (bia 0000.0ca5.238b) MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) [Additional display text omitted from this example] Router# show interfaces ethernet 3/0/3 Ethernet3/0/3 is administratively down, line protocol is down Hardware is cyBus Ethernet, address is 0000.0ca5.2303 (bia 0000.0ca5.238c) MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) [Additional display text omitted from this example] Router# show interfaces ethernet 3/0/4 Ethernet3/0/4 is administratively down, line protocol is down Hardware is cyBus Ethernet, address is 0000.0ca5.2304 (bia 0000.0ca5.238d) MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) [Additional display text omitted from this example]
Following is an example of the show interfaces ethernet command, which shows all of the information specific to interface 0 on a port adapter in port adapter slot 1 of a VIP2 in interface processor slot 3:
Router# show interfaces ethernet 3/1/0
Ethernet3/1/0 is administratively down, line protocol is down
Hardware is cyBus Ethernet, address is 0000.0ca5.2305 (bia 0000.0ca5.238e)
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255
Encapsulation ARPA, loopback not set, keepalive set (10 sec)
ARP type: ARPA, ARP Timeout 4:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters 2:56:26
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 input packets with dribble condition detected
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets, 0 restarts
0 output buffer failures, 0 output buffers swapped out
Proceed to the next section "Using the ping Command to Verify Network Connectivity" to check network connectivity of the PA-5EFL and switch or router.
Using the ping command, you can verify that an interface port is functioning properly. This section provides a brief description of this command. Refer to the publications listed in the "Related Documentation" section for detailed command descriptions and examples.
The ping command sends echo request packets out to a remote device at an IP address that you specify. After sending an echo request, the system waits a specified time for the remote device to reply. Each echo reply is displayed as an exclamation point (!) on the console terminal; each request that is not returned before the specified timeout is displayed as a period (.). A series of exclamation points (!!!!!) indicates a good connection; a series of periods (.....) or the messages [timed out] or [failed] indicate a bad connection.
Following is an example of a successful ping command to a remote server with the address 10.0.0.10:
Router# ping 10.0.0.10 <Return> Type escape sequence to abort. Sending 5, 100-byte ICMP Echoes to 10.0.0.10, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/15/64 ms Router#
If the connection fails, verify that you have the correct IP address for the destination and that the device is active (powered on), and repeat the ping command.
Proceed to the next section "Using loopback Commands" to finish checking network connectivity.
With the loopback test you can detect and isolate equipment malfunctions by testing the connection between the PA-5EFL interface and a remote device such as a modem or a CSU/DSU. The loopback subcommand places an interface in loopback mode, which enables test packets that are generated from the ping command to loop through a remote device or compact serial cable. If the packets complete the loop, the connection is good. If not, you can isolate a fault to the remote device or compact serial cable in the path of the loopback test.
Depending on the mode of the port, issuing the loopback command checks the following path:
Posted: Mon Feb 21 17:01:11 PST 2000
Copyright 1989 - 2000©Cisco Systems Inc.