Using the ROM Monitor

Entering the ROM Monitor

Command Conventions

Commands

Using the ROM Monitor

This appendix describes the Cisco uBR924 cable access router ROM monitor, which helps you isolate and troubleshoot possible hardware problems when installing the router. The ROM monitor is the first software to run when the Cisco uBR924 router is powered-on or reset; it is permanently part of the Cisco uBR924 router and is always available, regardless of the release of Cisco IOS software that has been downloaded to the router.

This appendix describes:

Entering the ROM monitor program
Aliasing ROM monitor commands
Using ROM monitor commands

Caution Users and system administrators do not need to access the ROM monitor during normal operation of the Cisco uBR924 router. The ROM monitor should be used only by trained service technicians or under the direction of a Cisco TAC engineer. Many of the commands available in the ROM monitor put the router in a diagnostic or non-functional state---do not enter any commands in the ROM monitor unless you thoroughly understand their function and how to reverse their effects so you can restore the router to normal operations.

Entering the ROM Monitor

The ROM monitor initializes the processor hardware and boots the main operating system software. The ROM monitor version introduced in the Cisco IOS Release 12.0(4)XI timeframe displays as follows:

rommon 2 > i 
System Bootstrap, Version 12.0(19990506:181223)[sjacobso-jac-xi26 2504] DEVELOPMENT
SOFTWARE
Copyright (c) 1994-1999 Cisco Systems, Inc.
UBR924 platform with 16384 Kbytes of main memory

The ROM monitor main memory information is shown below:

 rommon 3 > meminfo 
Main memory size: 16 MB
Available main memory starts at 0x14000, size 16304 KB
I/O (packet) memory size: 512 KB
NVRAM size: 16 KB

To default to booting at the ROM monitor while running the system software, reset the configuration register to 0x0 by entering configuration mode, and enter the configuration command following:

config-reg 0x0

The new configuration register value, 0x0, takes effect after the router is rebooted with the reload command. If you set the configuration to 0x0, you will have to manually boot the system from the console each time you reload the router.

Command Conventions

Following are ROM monitor command conventions:

Brackets [ ] denote an optional field. If a minus option is followed by a colon (for example: [-s:]), you must provide an argument for the option.
A word in italics means that you must fill in the appropriate information.
All address and size arguments to the memory-related commands are assumed to be hexadecimal (no "0x" prefix or "h" suffix needed).
The options [-bwl] for the memory-related commands provide for byte, word, and longword operations. The default is word.
You can invoke the memory-related commands by typing the command with no arguments. This causes the utility to prompt you for parameters. This option is available for the commands marked as prompting.
You can place more than one command (except the repeat command) on a line by using the ";" delimiter.

Commands

Enter ? or help at the rommon > prompt to display a list of available commands and options:

 rommon 12 > help
 
 alias               set and display aliases command
 boot                boot up an external process
 confreg             configuration register utility
 cont                continue executing a downloaded image
 context             display the context of a loaded image
 cookie              display contents of cookie PROM in hex
 dev                 list the device table
 dir                 list files in file system
 dnld                serial download a program module
 frame               print out a selected stack frame
 help                monitor builtin command help
 history             monitor command history
 meminfo             main memory information
 repeat              repeat a monitor command
 reset               system reset
 set                 display the monitor variables
 stack               produce a stack trace
 sync                write monitor environment to NVRAM
 sysret              print out info from last system return
 unalias             unset an alias
 unset               unset a monitor variable
 xmodem              x/ymodem image download

Note You can display additional details for a command by entering the command name with a -? option, which prints the command usage message.

The commands are listed and described in alphabetical order. Note that the ROM monitor commands are case-sensitive.

alias [name=value]---Aliases a name to a value. The ROM monitor's version of command aliasing is based on the aliasing function built into the Korn shell. Aliasing allows you to abbreviate commands or to set up a command so that it is automatically run with certain options.

: If the value contains white space or other special characters, it must be quoted. If the value has a space as the last character the next command line word is also checked for an alias (normally only the first word on the command line is checked).
: The alias command is used to set new aliases and to view the aliases that are currently defined. For example, to display the currently set aliases, enter the alias command by itself:

rommon 1 > alias 
r=repeat
h=history
?=help
b=boot
ls=dir

: The following command creates the alias "bf" that performs the "boot from Flash memory" command:

rommon 1 > alias bf "b flash:"

boot or b---Boots an image. The boot command with no arguments boots the first image in boot Flash memory. You can include an argument, filename, to specify a file to be booted over the network using the Trivial File Transfer Protocol (TFTP). The local device (see the description of b device following) can be specified by entering the device specifier (devid). If the specified device name is not recognized by the ROM monitor, the system will attempt to boot the image (imagename) from a network TFTP server. Do not insert a space between devid and imagename. Options to the boot command are -x, load image but do not execute, and -v, verbose. The form of the boot command follows:

boot [-xv] [devid] [imagename]

b---Boots the default (first) system software.

b filename [host]---Boots using a network TFTP server. When a host is specified, either by name or IP address, the boot command will boot from that source.

b flash:---Boots the first file in Flash memory.

: b device:---Boots the first file found in the Flash memory device. The Flash memory device specified can be either flash:, to boot the Cisco IOS software, or bootflash:, to boot the boot image in Flash memory.
: b device:name---An extension of the above command, allows you to specify a particular filename in the Flash memory.

confreg [hexnum]---Executing the confreg command with the argument hexnum changes the virtual configuration register to match the hex number specified. Without the argument, confreg dumps the contents of the virtual configuration register in English and allows the user to alter the contents. You are prompted to change or keep the information held in each bit of the virtual configuration register. In either case, the new virtual configuration register value is written into non-volatile memory (NVRAM, also known as Flash memory) and does not take effect until you reset or power cycle the router.

: The configuration register resides in Flash memory. The configuration register is identical in operation to other Cisco access servers. Enter confreg for the menu-driven system, or enter the new value of the register in hexadecimal.

Note The value is always interpreted as hexadecimal. The confreg utility will print a before and after view of the configuration register when used in menu-driven mode.

: For example:

         rommon 7 > confreg
 
     Configuration Summary
         enabled are:
         console baud: 9600
         boot: the ROM Monitor
 
         do you wish to change the configuration? y/n  [n]:  y
         enable  "diagnostic mode"? y/n  [n]:  y
         enable  "use net in IP bcast address"? y/n  [n]:  
         enable  "use all zero broadcast"? y/n  [n]:  
         enable  "ignore system config info"? y/n  [n]:  
         change console baud rate? y/n  [n]:  y
         enter rate: 0 = 9600, 1 = 4800, 2 = 1200, 3 = 2400  [0]:  0
         change the boot characteristics? y/n  [n]:  y
         enter to boot:
          0 = ROM Monitor
          1 = the boot helper image
          2-15 = boot system
     [0]:  0
 
     Configuration Summary
         enabled are:
         diagnostic mode
         console baud: 9600
         boot: the ROM Monitor
 
         do you wish to change the configuration? y/n  [n]:  
 
         You must reset or power cycle for new config to take effect.

cont [-b]---Continues a loaded image that has stopped. For example:

     reboot> launch 
          monitor: command "launch" aborted due to user interrupt
         diagmon 7 > cont 
 
         reboot >

context---Displays the CPU context at the time of the fault. The context from the kernel mode and process mode of a booted image is displayed, if available. For example:

         rommon 6 > context
         CPU Context:
         d0 - 0x00000028      a0 - 0x0ff00420
         d1 - 0x00000007      a1 - 0x0ff00000
         d2 - 0x00000007      a2 - 0x02004088
         d3 - 0x00000000      a3 - 0x020039e6
         d4 - 0x00000000      a4 - 0x02002a70
         d5 - 0x02003e8a      a5 - 0x02003f17
         d6 - 0x00000000      a6 - 0x02003938
         d7 - 0x00000001      a7 - 0x0200392c
         pc - 0x02004adc     vbr - 0x02000000

cookie---Displays the contents of the cookie PROM in hexadecimal format. For example:

         rommon 1 > cookie
         cookie:
         01 01 00 00 0c 07 af 80 07 00 00 00 00 00 00 00
         00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

dev---Lists boot device identifications on the router. For example:

         rommon 10 > dev
         Devices in device table:
        id  name
    eprom:  eprom
    flash:  PCMCIA slot 1

dir devid---Lists the files on the named device. For example:

         rommon 11 > dir flash:
        File size                Checksum      File name
            65 bytes (0x41)       0xb49d       clev/oddfiles65
       2229799 bytes (0x220627)   0x469e       C5200-k.z

dlnd [-xv:] [args]---Downloads in binary format through the console and executes. The -x option downloads, but does not execute. The -v option allows you to specify the verbose level. The optional arguments are passed to the downloaded program via the argc/argv mechanism (only when -x is not used). The exit value is the return value from the downloaded routine or the status of the download operation (success or failure) if the -x option is used.
frame [number]---Displays an entire individual stack frame. Enter a number to indicate which frame to display. You can also specify a number to indicate which stack frame to display. Note that the default is 0 (zero), which is the youngest frame. For example:

         rommon 6 > frame 2
         Frame 02: FP = 0x02003960    RA = 0x020050ee
         at 0x02003968 (fp + 0x08) = 0x02004f8d
         at 0x0200396c (fp + 0x0c) = 0x0200f390
         at 0x02003970 (fp + 0x10) = 0x02006afc
         at 0x02003974 (fp + 0x14) = 0xc0a82983
         at 0x02003978 (fp + 0x18) = 0x02003a7e
         at 0x0200397c (fp + 0x1c) = 0x02002630
         at 0x02003980 (fp + 0x20) = 0x00000000
         at 0x02003984 (fp + 0x24) = 0x02000000
         at 0x02003988 (fp + 0x28) = 0x0200c4a4
         at 0x0200398c (fp + 0x2c) = 0x0200f448

history or h---Displays the command history, that is, the last 16 commands executed in the monitor environment.
meminfo---Displays the size (in bytes) the starting address, the available range of the main memory, the starting point and size of packet memory, and the size of non-volatile Flash memory. For example:

         rommon 9 > meminfo
 
         Main memory size: 8 MB. Packet memory size: 4 MB
         Available main memory starts at 0xa000e001, size 0x7f1fff
         Packet memory starts at 0xa8000000
         NVRAM size: 0x20000

repeat [number or string] [count] or r---Repeats the specified command. Without an argument, repeats the last command. The optional command number (from the history list) or match string specifies which command to repeat. In the case of the match string, the most recent command to begin with the specified string will be re-executed. If the string includes spaces, you must define it using quotes. The count option allows you to repeat the command more than once.
reset or i---Resets and initializes the system, similar to power-on.
set---Displays all the monitor variables and their values.
stack [num]---Produces a stack trace of the num frames. The default is 5. The command dumps from the kernel stack and the process stack (if one is available) of a booted image. For example:

         rommon 5 > stack 8
         Stack trace:
         PC = 0x02004adc
         Frame 00: FP = 0x02003938    RA = 0x02005f2a
         Frame 01: FP = 0x02003948    RA = 0x02005df0
         Frame 02: FP = 0x02003960    RA = 0x020050ee
         Frame 03: FP = 0x02003994    RA = 0x02004034
         Frame 04: FP = 0x02003b00    RA = 0x00012ca6

sync---Writes the working in-core copy of the environment variables and aliases to Flash memory so that they are read on the next reset.
sysret---Displays the return information from the last booted system image. This includes the reason for terminating the image, a stack dump of up to eight frames, and if an exception is involved, the address where the exception occurred. For example:

         rommon 8 > sysret
         System Return Info:
         count: 19,  reason: reset
         pc:0x60043754,  error address: 0x0
         Stack Trace:
         FP: 0x80007e78, PC: 0x60043754
         FP: 0x80007ed8, PC: 0x6001540c
         FP: 0x80007ef8, PC: 0x600087f0
         FP: 0x80007f18, PC: 0x80008734

unalias name---Removes name and its associated value from the alias list.

Table of Contents