Table of Contents

A

alias command     A-3

B

boot command     A-3

booting

from the ROM monitor     A-3

C

cable

jacks, in wet locations     2-2

safety guidelines     2-2

ungrounded and uninsulated     2-2

Cable Link LED     4-5

cables

4E RJ-45 pinout     2-7

caution

antistatic strap     2-3

cable modem, overheating     2-13

scoring coaxial cable connectors     2-12

Cisco IOS

command modes     5-3

enable mode     5-4

getting help     5-3

undo command     5-5

undo feature     5-5

coaxial cable     4-6

condition of     4-6

subsystem for troubleshooting     4-3, 4-6

command

alias     A-3

boot     A-3

confreg     A-3

cont     A-4

context     A-5

cookie     A-5

dev (device)     A-5

dir     A-5

dlnd     A-5

frame     A-6

history     A-6

meminfo     A-6

repeat     A-6

reset     A-6

ROM monitor     A-2

ROM monitor diagnostics     A-1

set     A-6

stack     A-6

sync     A-6

sysret     A-7

unalias     A-7

command modes

Cisco IOS     5-3

configuration register     A-4

confreg command     A-3

connection equipment

console port signals     5-2

connections

coaxial cable     3-5, 3-7

power     3-9

connector

console port     5-2

Ethernet RJ-45     3-8, 3-10

console terminal, system banner display     5-2

cont command     A-4

context command     A-5

cookie command     A-5

crossover cable connection     2-7, 2-8

D

dev (device) command     A-5

diagnostics

ROM monitor     A-1

digital signal, subsystem for troubleshooting     4-3

dir command     A-5

distance limitations, transmission     2-12

dlnd command     A-5

E

electromagnetic pulse (EMP), avoiding     2-11

EMI, shielding     2-2

enable mode     5-4

Ethernet 0 LED     4-5, 4-10

F

frame command     A-6

H

help, Cisco IOS     5-3

history command     A-6

I

installation

connecting console cables     5-1

connecting the CATV cable     3-5, 3-7

interference, radio frequency     2-11

J

jewelry, avoiding for safety     2-1

L

LEDs

1     4-5

Link     4-5

OK     4-5

lightning storm, safety during     2-2

M

meminfo command     A-6

N

note, description of     ix

O

operating conditions for unit     1-4

P

personal computer

subsystem for troubleshooting     4-3

pinouts

RJ-45

4E     2-7

power

connections     3-9

site requirements     3-5

subsystem for troubleshooting     4-3, 4-6

surge suppression     2-11

ungrounded     2-2

power factor corrector, power supply     3-5

power supply, physical description     1-4

problem solving, subsystem     4-3

procedures

connecting console cables     5-1

connecting the CATV cable     3-5, 3-7

R

repeat command     A-6

reset command     A-6

RF signal, subsystem for troubleshooting     4-3

RJ-45

4E

cable     2-7

ROM monitor

commands     A-2

diagnostics     A-1

entering

     A-1

S

safety recommendations

preventing electrostatic discharge damage     2-2

safety with electricity     2-2

Section

Customizing the Cable Modem Interface     5-41

set command     A-6

site requirements

environment     2-13

power     3-5

stack command     A-6

subsystems for troubleshooting

coaxial cable     4-6

power     4-6

sync command     A-6

sysret command     A-7

system specifications     1-5

System status LED     4-5

T

timesaver, description     ix

troubleshooting

coaxial cable subsystem     4-6

identifying installation problems     4-2

power subsystem     4-6

strategy     4-4

U

unalias command     A-7

undo feature, Cisco IOS     5-5

User LED 1     4-5

User LED 2     4-5

User LED 3     4-5

W

wiring

quality and requirements     2-11

Posted: Wed Aug 25 18:11:51 PDT 1999
Copyright 1989-1999©Cisco Systems Inc.