|
|
This section describes the fixed wireless point-to-point commands that are used to configure, maintain, and troubleshoot the fixed wireless point-to-point system supported on the uBR7200 series universal broadband router. See the following sections for more information:
The fixed wireless point-to-point commands operate on the Cisco uBR7200 series universal broadband router (the Cisco uBR7223, the Cisco uBR7246, and the Cisco uBR7246 VXR). The Cisco fixed wireless point-to-point system is supported on the Cisco IOS 12.1(3)T Release.
This section describes the commands used to configure and maintain the Cisco fixed wireless point-to-point radio modem feaures. The commands are listed alphabetically.
To clear link metrics settings, use the clear radio interface radio privileged EXEC command.
clear radio interface radio slot/port link-metrics
Syntax Description
slot/port The slot and port address.
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
12.0(7)XR This command was introduced.
Release
Modification
Examples
By using the following command, you can clear all radio link-metrics details:
UBR04 # clear radio interface radio 6/0 link-metrics
To place the specified module in loopback mode, use the loopback interface configuration command. To remove the loopback, use the no form of this command.
loopback [local module]
Syntax Description
local (Optional) Specifics that the module is local. module Specifies the type of module:
{codec | fir | if [diversity | dual | main] | rf [diversity | main]}
Defaults
Local IF loopback
Command Modes
Interface configuration
Command History
11.0 This command was introduced. 12.0(7)XR Support for the uBR7200 series router and the local keyword was added.
Release
Modification
Usage Guidelines
If you perform a loopback of the RF module while the transverter is attached to an antenna, some transmit power is radiated. Because of this, it is extremely important that you set the transmit frequency be set to your assigned and licensed frequency. If the transverter is not attached to an antenna, attach an RF termination device to the duplexer port. (For information regarding RF termination devices, refer to Cisco Broadband Fixed Wireless Site Planning Guide.)
Examples
The following example initiates a local RF loopback:
UBR04(config-if)# loopback local rf
The following example shows the set of loopbacks currently in effect for the modem card in slot 3, port 0 of the Cisco uBR7200 series router:
UBR04# show interfaces radio 3/0
Radio3/0 is up, line protocol is up (looped)
Hardware is CWR P2P
Internet address is 10.0.0.13/24
MTU 1500 bytes, BW 44419 Kbit, DLY 11000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback set
Keepalive set (10 sec)
Last input 00:00:01, output 00:00:01, output hang never
Last clearing of "show interface" counters never
Queueing strategy: fifo
Output queue 0/40, 8 drops; input queue 0/75, 0 drops
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
620 packets input, 203300 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 output errors, 0 collisions, 4 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
Related Commands
show interfaces radio Displays the set of loopbacks currently in effect for the specified modem card.
Command
Description
To align the receive antenna to the transmitter, use the radio antenna-alignment interface configuration command. To cancel antenna alignment mode, use the no form of this command.
radio antenna-alignmentSyntax Description
This command has no arguments or keywords.
Defaults
No default behavior or values.
Command Modes
Interface configuration
Command History
12.0(7)XR This command was introduced.
Release
Modification
Usage Guidelines
Do not use this command during normal operation; its use will degrade the performance of the radio link.
Examples
The following example initiates antenna alignment mode during installation:
UBR04(config-if)# radio antenna-alignment
Related Commands
show running-configuration interface Displays the current interface settings.
Command
Description
To configure the Automatic Repeat Query (ARQ) mechanism on the wireless modem card, use the radio arq interface configuration command. To use default values, use the no form of this command.
radio arq {pctBw dataLatency [BurstSize]} {on | off] [reset}
Syntax Description
pctBw Positive number representing the highest percentage of the link bandwidth to be used for the ARQ mechanism. The value can be 1 to 5000, representing 0.01 to 50 percent of the available bandwidth. The default value is 1250. dataLatency Positive number specifying the expected latency value for normal data. Latency values are measured in milliseconds. The default value is 11 ms. BurstSize Positive number specifying the maximum number of consecutive ARQ codewords that will be transmitted. Small values result in less jitter. The default value is 8.
Note Regardless of the pctBw setting, link bandwidth is only consumed by ARQ when there are data errors that need to be corrected.
Note The default latency value for arq on is 11 ms, which can be used for all combinations of bandwidth and throughput. When ARQ is off, the latency value will be 2 ms for each direction of the link.
Defaults
pctBw 1250, dataLatency 11 ms, BurstSize 8
Command Modes
Interface configuration
Command History
12.0(7)XR This command was introduced. 12.1(1)T The voiceLatency parameter was removed and the BurstSize default was changed.
Release
Modification
Usage Guidelines
ARQ enables the transmitter to resend data that is received in error at the receiver. This allows the radio link to run at a substantially lower error rate in RF channels with rapid fading or bursty interference.
Enabling requires a small amount of additional overhead and increases the latency of the link. However, even with small maximum latency and maximum overhead settings, enabling ARQ can dramatically improve link performance.
Latency values should be related to the bandwidth and throughput settings for channel-setup (See Table 53).
| Bandwidth | Throughput | Minimum Latency |
|---|---|---|
6 MHz | Low | 11 ms |
6 MHz | Medium | 7 ms |
6 MHz | High | 7 ms |
12 MHz | Low | 7 ms |
12 MHz | Medium | 6 ms |
12 MHz | High | 5 ms |
Parameters can only be changed when the radio link of down (shut), and will not take effect until the next no shut command is entered.
Use the on/off option to turn on or off the ARQ feature on the link.(If ARQ is turned off, it may be difficult to establish the radio link in adverse environments.)
Use the reset option to reset the current ARQ values to consistent settings based on the channel-parameter configuration.
Examples
See the following command which sets the ARQ mechanism for 0.01% of the bandwidth, a 10-millisecond latency value, and 24 consecutive ARQ codewords:
UBR04(config-if)# radio arq 1 10 24
To specify the collection interval for the histogram for uncorrected codewords, and how often the collected histogram data is printed to the display screen, use the radio byteErrorHist interface configuration command.
To stop collecting and displaying histrogram data, use the no form of this command.
radio byteErrorHist [collectionInterval interval] [periodic interval sum {true | false}]
Syntax Description
collectionInterval interval Specifies, in seconds, the duration of histogram data collection. periodic interval Specifies, in seconds, how often the collected histogram data is printed to the screen. The sum option specifies whether successive histogram sets retrieved from the hardware is added to replace the existing histogram data. Use an interval of 0 to print the data to the screen only at termination of the collection.
Defaults
No default behavior or values.
Command Modes
Interface configuration
Command History
12.0(7)XR This command was introduced.
Release
Modification
Examples
The following example configures a collection interval of 1 hour and print to the screen every 30 seconds:
UBR04(config-if)# radio byteErrorHist collectionInterval 3600 periodic 30 sum false
To determine the effective cable loss (measured in dB at 400 MHz) of the cable between the wireless modem card and the specified wireless transverter, including the power feed panel, connectors, and lightning protection, use the radio cable-loss interface configuration command. To stop measuring cable loss, use the no form of this command.
radio cable-loss antenna_num positive number
Syntax Description
antenna_num Enter 1 (main antenna) or 2 (diversity antenna). positive number Positive number (less than or equal to 12 dB), reflecting effective cable loss.
Defaults
No default behavior or values.
Command Modes
Interface configuration
Command History
12.0(7)XR This command was introduced.
Release
Modification
Usage Guidelines
Do not set the cable loss parameter to a value greater than 12 dB. The exact cable loss value is determined by the transverter. The system checks against that value when you enter the a no shut command.
Examples
The following example adjusts the effective cable loss parameter for antenna 1 to 12 dB:
UBR04(config-if)# radio cable-loss 1 12
Related Commands
show running-configuration interface radio Displays the current radio cable loss setting.
Command
Description
To adjust bandwidth and throughput to increase the reliability of the link, use the radio channel-setup interface configuration command. To reset the parameters to their default values, use the no form of this command.
radio channel-setup bandwidth bw throughput dataThroughput {high | medium | low} burstsize BurstSize {small | medium | large}
Syntax Description
bw {6.0 | 12.0} dataThroughput {high | medium | low} high (default) At 12 MHz, maximum 44.4 Mbps medium At 12 MHz, maximum 39.1 Mbps low At 12 MHz, maximum 22.4 Mbps BurstSize {small | medium | large} small Reduced burst size with increased burst frequency. Designed for specific uses. medium (default) Required by all U-NII transverters. large Increased burst size with reduced burst frequency. Designed for special uses.
At 6 MHz, maximum 22.2 Mbps
At 6 MHz, maximum 19.6 Mbps
At 6 MHz, maximum 11.2 Mbps
Defaults
Bandwidth 6.0, throughput high, burstsize medium
Command Modes
Interface configuration
Command History
12.0(7)XR This command was introduced. 12.1(1)T BurstSize parameter was added.
Release
Modification
Usage Guidelines
Multipath delay spread is one of two fundamental limits to the performance of a digital radio link. The other limit is the Signal to Interference plus Noise ratio (SINR) which is described in Cisco uBR7200 Series Universal Broadband Router Wireless Modem Card and Subsystem Installation and Configuration.
Multipath delay spread occurs when the signal arrives at the receiver through multiple paths with differing path lengths. Signals that take long paths arrive later than signals that take shorter paths. The delay spread is the difference between the time it takes for the shortest path signal and the longest path signal to arrive. Typically, delay spread is the longest in urban areas with many buildings acting as reflectors. Delay spread is more important when the direct path between antennas is blocked, making the delayed signals stronger relative to the direct signal.
Both 6 MHz and 12 MHz bandwidths are available. For each of these bandwidths, there are three possible throughput setting: high, medium, and low.
The low setting uses the most error-correction coding and can handle the most multipath delay spread.
The medium setting uses less error-correction coding, but can still handle the most multipath delay spread.
The high setting uses less error-correction coding and can handle less multipath delay spread. For a selected bandwidth, data throughput can be reduced to increase reliability.
Enter this command at any time. If the link is up when you enter the command, it takes effect with the next shut/no shut. If the link is down when you enter the command, it takes effect with the next no shut.
Command History
shut Stops the link (if it is up). no shut starts the link and implements any bandwidth changes. show running-configuration interface radio Displays the current settings.
Command
Description
To enter duplexer specifications, use the radio duplexor interface configuration command.
radio duplexor antenna_num PartNum LoPassbandRange HiPassbandRange RxPassband [low-passband | hi-passband] CLEIcode VendorName SerialNumber
Syntax Description
antenna_num Enter 1 (main antenna) or 2 (diversity antenna). PartNum A string representing the duplexer's Cisco part number. LoPassbandRange Identifies the duplexer's low-frequency range. This range is lower than the range specified in the HiPassbandRange parameter. HiPassbandRange Identifies the duplexer's high-frequency range. This range is higher than the range specified in the LoPassbandRange parameter. RxPassband Identifies the frequency range used to receive transmissions. CLEIcode Common Language Equipment Identifier code. VendorName The name of the vendor of the duplexer. SerialNumber Serial number of the duplexer.
Identifies the antenna to which the duplexer is connected.
Defaults
No default behavior or values.
Command Modes
Interface configuration
Command History
12.0(7)XR This command was introduced.
Release
Modification
Usage Guidelines
The duplexer is a mechanical device that acts as a band pass filter when installed in the wireless transverter. This filter restricts the transverter to operate in a specified part of the frequency spectrum. One duplexer provides a high- and low-frequency specification for one wireless transverter.
You can find most of the information on the tear-off label attached to the underside of the duplexer.
To control the printing of radio histogram information to the screen, use the radio histdisplay interface configuration command.
radio histdisplay statParam antenna_num [dsp dspId] {on | off}
Syntax Description
statParam {in | inr | constVariance | timingOffset | freqOffset | syncStatus | receivedPower | gainSettingsIF | gainSettingsRF | totalGain} The data for the radio attribute is collected as a histogram. antenna_num Enter 1 (main antenna) or 2 (diversity antenna). dsp dspId {dsprxla (Receive DSP 1a) | dsprx1b (Receive DSP 1b) | dsprx2a (Receive DSP 2a) | dsprx2b (Receive DSP 2b) | dsprx3a (Receive DSP 3a) | dsprx3b (Receive DSP 3b) |
dsptx1 (Transmit DSP 1) | dsptx2 (Transmit DSP 2)}
Defaults
No default behavior or values.
Command Modes
Interface configuration
Command History
12.0(7)XR This command was introduced.
Release
Modification
Related Commands
radio histogram Configures a histogram collection of radio traffic on the specified interface. radio interface histclear Removes radio histograms.
Command
Description
To configure a histogram collection specification, use the radio histogram interface configuration command. To delete existing histogram collections, use the no form of this command.
radio histogram statParam antenna_num [dsp dspId] StartBinValue BinDelta NumBins BitShift [collectionInterval interval] [periodic interval sum {true | false}] [tone circulate | average | number tone-number]
Syntax Description
statParam {in | inr | constVariance | timingOffset | freqOffset | syncStatus | receivedPower | gainSettingsIF | gainSettingsRF | totalGain} The data for the radio attribute is collected as a histogram. in (Interference + Noise) The interference plus noise power levels are computed by the hardware on a burst-by-burst basis. inr (Interference + Noise Ratio) The ratio of the interference plus noise power levels captured by the first antenna to the second antenna on a burst-by-burst basis. This value is specified as a log to base 2 number. constVariance (Constellation Variance) The average energy of the constellation error signal - the error between the received (noisy) constellation symbol and the nearest ideal constellation symbol. Constellation Variance is a measure of the SINR for that tone. On a single antenna system, Constellation Variance is proportional to (SINR)-1. On a dual antenna system, it represents a composite value that is proportional to (SINR)-1. timingOffset Represents the timing delay variations detected in the radio link. freqOffset Represents the carrier frequency offset between the slave radio and the master radio. syncStatus Represents the synchronization status. receivedPower A measure of the analog signal power received by the radio system on a burst-by-burst basis. gainSettingsIF Represents the IF attenuation value commanded by the automatic gain control loop. This can be captured for each antenna and for the intermediate frequency (IF) module. gainSettingsRF Represents the RF attenuation value commanded by the automatic gain control loop. This can be captured for each antenna and for the radio frequency (RF) module. totalGain Represents the total attenuation commanded by the automatic gain control loop. This can be captured for each antenna. antenna_num Enter 1 (main antenna) or 2 (diversity antenna). dspId {dsprx1a (Receive DSP 1a) | dsprx1b (Receive DSP 1b) | dsprx2a (Receive DSP 2a) | dsprx2b (Receive DSP2b) | dsprx3a (Receive DSP 3a) | dsprx3b (Receive DSP 3b)} StartBinValue Any value below this value is not stored in the histogram. Range is -231 to 232-1. BinDelta The "width" of each histogram bin. For example, if the StartBinValue is 10 and BinDelta is 64, then all values in the range 10 to 74 will be in the first bin. All values from 75 to 138 will be in the second bin, and so on. Range is 2 to 2^32 and must be a power of 2. NumBins The number of histogram bins to be configured for the collection. Range is 0 to 508. BitShift Specifies the number of bits by which the collected data is shifted to the right, providing a mechanism to control overflow of the values in the histogram. Range is 0 to 31. collectionInterval Specifies, in seconds, the interval in which histogram data will be collected. periodic Specifies, in seconds, how often the collected histogram data is printed to the screen. The sum option specifies whether successive histogram sets retrieved from the hardware are added to replace the existing histogram data. Specifying a statistic collection to be periodic effectively reduces the size of the NumBins to half the possible amounts. The default is periodic. If the interval is 0, output is generated only at the termination of the collection. tone Identifies how the histogram sample is computed when sampling a burst. A burst contains data samples from N frequency tones. circulate Implies successive histogram data samples use successive frequency tones. average Implies successive histogram samples average the burst data over all the frequencies and use that value. number Specifies that a particular tone in the burst is used to report the histogram data. The frequency tone is passed in as a number specified in the tone-number parameter.
Note This parameter is available for a dual antenna system only.
Defaults
No default behavior or values.
Command Modes
Interface configuration
Command History
12.0(7)XR This command was introduced.
Release
Modification
Usage Guidelines
A histogram is a collection of statistics sampled over time on a burst-by-burst basis and presented as a function of Bins. The number of Bins as well as the size of Bins is user defined.
The data for the histogram is collected as soon as the command succeeds and continues until either the specification is deleted using the no option, or the specified collectionInterval expires. The collected data is printed out to the console at user-specified intervals.
A histogram statistic is created when data is sampled for every burst. For each sampled burst, the count in a specific bin is incriminated. The number of Bins in the histogram is specified by the NumBins parameter.
For every histogram defined, antenna_num and tone are conditional. The antenna_num is required for the attributes in, receivedPower, GainSettingsIF, gainSettingsRF, and totalGain. Optionally, You may specify Tone for the attributes in, inr, and constVariance.
|
Note There should be no measurable impact or degradation of router performance from running histograms. Cisco recommends that you keep the number of histograms run simultaneously to a minimum and that you terminate any histograms no longer needed. |
Up to 1024 32-bit words are available for all histogram parameters on a single DSP. Each histogram requires (NumBins + 4) * 2 words. The attributes in in, inr, and constVariance can be captured on any DSP while the others can be captured only on certain DSPs. Distributing histogram requests across DSPs provides better memory utilization. In general, it is best not to specify the DSPs without special knowledge of the system.
For more information on DSPs, see Cisco uBR7200 Series Universal Broadband Router Wireless Modem Card and Subsystem Installation and Configuration.
Examples
The following example configures a histogram specification. The histogram collection starts as soon as the command succeeds and collects a histogram for interference noise ratio. The histogram is collected with starting Bin of 2-4 (a starting ratio of 0.0625), bindelta of 1, 32 bins in total, and no bitshift. Then the results are averaged on all frequency tones for each sample. The collection continues for 1 hour, reports data every 30 seconds, and keeps the cumulative histogram.
UBR04(config-if)# radio histogram inr -4 1 32 0 collectionInterval 3600 periodic 30 tone
average sum true
Related Commands
radio histdisplay Displays radio histograms. radio interface histclear Removes radio histograms.
Command
Description
To add the specified image to the image repository, use the radio image-add privileged EXEC command. To delete the specified image from the repository, use the no form of this command.
radio image-add protocol://host/directory/filename
Syntax Description
protocol {mem | tftp | flash} host IP address. directory Directory name. (No embedded spaces accepted.) filename Name of image file.
Defaults
No default behavior or values.
Command Modes
Privileged EXEC
Command History
12.0(7)XR This command was introduced.
Release
Modification
Usage Guidelines
When an image has to be downloaded according to the specified configuration, the repository is searched for an appropriate file. If found, the file is retrieved and downloaded to the hardware.
Examples
The following commands selects the image dspla.img at the address 192.168.33.44 to be added to the repository:
UBR04# radio image-add tftp://192.168.33.44/myDspImages/dspla.img
Related Commands
radio image-move Moves the specified image to the beginning of the repository. show radio repository Displays the repository contents.
Command
Description
To move the specified image to the beginning of the repository list of images, use the radio image-move privileged EXEC command.
radio image-move protocol://host/directory/filename
Syntax Description
protocol {mem | tftp | flash} host IP address. directory Directory name. (No embedded spaces accepted.) filename Name of image file.
Defaults
No default behavior or values.
Command Modes
Privileged EXEC
Command History
12.0(7)XR This command was introduced.
Release
Modification
Usage Guidelines
When the radio card is initiated (no shut), the repository is searched for a firmware image with characteristics matching the current configuration. Once found, that image is downloaded. Moving an image to the beginning of the list ensures that the image is searched first when a configuration match is attempted.
Examples
The following example selects the image dspla.img at the address 192.168.33.44 to be moved to the start of the repository list:
UBR04# radio image-move tftp://192.168.33.44/myDspImages/dspla.img
Related Commands
radio image-add Adds the specified image to the repository. show radio repository Displays the repository contents.
Command
Description
To clear collected radio histogram data, use the radio interface histclear interface configuration command.
radio interface slot/port histclear statParam antenna_num [dsp dspId]
Syntax Description
statParam {in | inr | constVariance | timingOffset | freqOffset | syncStatus | receivedPower | gainSettingsIF | gainSettingsRF | totalGain} The radio attribute whose data is to be collected as a histogram. antenna_num Enter 1 (main antenna) or 2 (diversity antenna). dspId {dsprx1a (Receive DSP 1a) | dsprx1b (Receive DSP 1b) | dsprx2a (Receive DSP 2a) | dsprx2b (Receive DSP2b) | dsprx3a (Receive DSP 3a) | dsprx3b (Receive DSP 3b)} The DSP where the timeline data is collected.
Defaults
No default behavior or values.
Command Modes
Interface configuration
Command History
12.0(7)XR This command was introduced.
Release
Modification
Related Commands
radio histdisplay Controls how the histogram data appears. radio histogram Configures a histogram collection specification.
Command
Description
To capture another snapshot on the identified DSP, use the radio interface radio snapcapture interface configuration command.
radio interface radio slot/port snapcapture dspId
Syntax Description
slot/port The slot and port address. dspId The DSP ID:
{dsprxla (Receive DSP 1a) | dsprx1b (Receive DSP 1b) | dsprx2a (Receive DSP 2a) | dsprx2b (Receive DSP 2b) | dsprx3a (Receive DSP 3a) | dsprx3b (Receive DSP 3b) |
dsptx1 (Transmit DSP 1) | dsptx2 (Transmit DSP 2)}
Defaults
No default behavior or values.
Command Modes
Interface configuration
Command History
12.0(7)XR This command was introduced.
Release
Modification
Usage Guidelines
The snapshot specification already configured on the DSP is used.
Related Commands
radio snapshot Creates a snapshot specification. radio interface radio snapclear Clears the data collected for the specified snapshot. show interfaces radio snapdata Displays the data captured for the snapshot specification.
Command
Description
To clear the data collected for the specified snapshot on the identified DSP, use the radio interface radio snapclear interface configuration command.
radio interface radio slot/port snapclear dspId
Syntax Description
slot/port The slot and port address. dspId {dsprxla (Receive DSP 1a) | dsprx1b (Receive DSP 1b) | dsprx2a (Receive DSP 2a) | dsprx2b (Receive DSP 2b) | dsprx3a (Receive DSP 3a) | dsprx3b (Receive DSP 3b) |
dsptx1 (Transmit DSP 1) | dsptx2 (Transmit DSP 2)}
Defaults
No default behavior or values.
Command Modes
Interface configuration
Command History
12.0(7)XR This command was introduced.
Release
Modification
Related Commands
radio snapshot Creates a snapshot specification. radio interface radio snapcapture Captures a snapshot on the specified DSP. show interfaces radio snapdata Displays the data captured for the snapshot specification.
Command
Description
To start a stopped timeline specification, use the radio interface radio timelineStart privileged EXEC command.
radio interface radio slot/port timelineStart statParam antenna_num [dsp dspnum]
Syntax Description
slot/port The slot and port of the interface. statParam {in | inr | constVariance | timingOffset | freqOffset | syncStatus | receivedPower | gainSettingsIF | gainSettingsRF} The radio attribute whose data is to be collected as a histogram. antenna_num Enter 1 (main antenna) or 2 (diversity antenna). dspnum The DSP number.
Defaults
No default behavior or values.
Command Modes
Privileged EXEC
Command History
12.0(7)XR This command was introduced.
Release
Modification
Usage Guidelines
Unless an error occurs, no notifications appear on the console.
Related Commands
radio timeline Configures a timeline collection specification. radio interface radio timelineStop Stops a running timeline specification. show interfaces radio tldata Displays timeline data for the specified card. show interfaces radio tlspec Displays the details of the timeline specification.
Command
Description
To stop a currently executing timeline specification, use the radio interface radio timelineStop privileged EXEC command.
radio interface radio slot/port timelineStop statParam antenna_num [dsp dspnum]
Syntax Description
slot/port The slot and port of the interface. statParam {in | inr | constVariance | timingOffset | freqOffset | syncStatus | receivedPower | gainSettingsIF | gainSettingsRF} The radio attribute whose data is to be collected as a histogram. antenna_num Enter 1 (main antenna) or 2 (diversity antenna). dspnum The DSP number.
Defaults
No default behavior or values.
Command Modes
Privileged EXEC
Command History
12.0(7)XR This command was introduced.
Release
Modification
Related Commands
radio timeline Configures a timeline collection specification. radio interface radio timelineStart Starts a stopped timeline specification. show interfaces radio tldata Displays timeline data for the specified card. show interfaces radio tlspec Displays the details of the timeline specification.
Command
Description
To manually highlight specific conditions on a specified wireless modem card using the five LEDs on the card, use the radio led interface configuration command. To reset the settings of the LED to the default values, use the no form of this command.
radio led {latchLeds latchLedOptions | otherLeds otherLedOptions}
Syntax Description
latchLeds {led-major-alarm | led-minor-alarm} led-major-alarm Indicates the occurrence of a major alarm in the radio subsystem. Unless you override the default mode, the LED remains illuminated for the duration of the alarm. led-minor-alarm Indicates the occurrence of a minor alarm in the radio subsystem. Unless you override the default mode, the LED remains illuminated for the duration of the alarm. latchLedOptions {latch | off | green | yellow | blinkGreen | blinkYellow | blinkBoth} latch The system turns the LED on indicating an alarm condition; the operator must turn off the alarm by entering the radio led latchLeds latch command. off This forces the LED to turn off and remain off under all conditions. green Lamp test for the LED. The LED turns green and remains green under all conditions. yellow Lamp test for the LED. The LED turns yellow and remains yellow under all conditions. blinkGreen The green LED blinks. blinkYellow The yellow LED blinks. blinkBoth Alternately blinks the LED yellow and green. otherLeds {led-carrier | led-service | led-ok} led-carrier Represents the state of the radio link. This LED cannot be latched, but the operator can turn these LEDs on or off manually.
Note The latch option is available only for led-major-alarm and led-minor-alarm.
led-service | Indicates the service availability on this radio link. This LED cannot be latched, but the operator can turn these LEDs on or off manually. This LED is operator-controlled only. |
led-ok | Indicates that the wireless modem card is on, is receiving from the router midplane, and is enabled for operation. This LED remains on during normal operation of the router. |
otherLedOptions | {off | green | yellow | blinkGreen | blinkYellow | blinkBoth} |
Defaults
LEDs controlled by system
Command Modes
Interface configuration
Command History
12.0(7)XR This command was introduced.
Release
Modification
Usage Guidelines
There are three categories of LEDs: alarm, user-controlled, and other LEDs. The two alarm LEDs normally remain illuminated only for the duration of the alarm. However, you can override this condition using the latch form of the command which causes the LEDs to remain illuminated until you enter the latch form of the command to clear the LEDs.
The led-service LED can only be controlled by entering an LED command. All the LEDs can be forced to illuminate or blink under operator control. This can be used as a "lamp test" to verify that the hardware is functional or to remotely indicate a specific wireless modem card to be examined.
Examples
The following example sets the behavior of the major alarm LED to be controlled by the system at all times:
UBR04(config-if)# no radio led led-major-alarm
Related Commands
show interfaces radio Displays the current configuration and state of the LEDs.
Command
Description
To configure the wireless modem card to operate as the master radio, use the radio master interface configuration command. To force the radio card to operate as the slave, use the no form of this command.
radio master [external-clock-reference]
Syntax Description
external clock-reference Option. Indicates that an external reference is being used. In slave mode, the default is automatically set to internal clock reference.
Defaults
Slave mode
Command Modes
Interface configuration
Command History
12.0(7)XR This command was introduced.
Release
Modification
Usage Guidelines
The master radio acts as the frequency source; the radio designated as the slave tracks changes in the master's frequency.
|
Note To avoid unpredictable results, designate one end (either end) of the link as "master." |
Enter this command only when the radio link is down (shut). The command takes effect only when the link is again active (no shut). Use the no version of the command to switch the modem card from master to slave mode.
|
Note Configure the center frequency of both master and slave by using the appropriate operating band and channel parameters commands. |
|
Note The attached external clock reference must be exactly 10 MHz for the link to function properly. |
Examples
The following example configures the wireless modem card to operate as the master radio with internal clock reference:
UBR04(config-if)# radio master
Related Commands
show running-configuration interface radio Displays the current setting.
Command
Description
To configure thresholds that determine when a second is classified as ES, DS, SES, or CSES for the radio link to measure how well the radio link is performing over time, use the radio metrics-threshold code-word interface configuration command. To force the thresholds back to the default values, use the no form of this command.
radio metrics-threshold code-word ESThresh DSThresh SESThresh CSESThresh
Syntax Description
ESThresh Specifies the number of codeword errors that must be detected within a 1-second interval for that second to be treated as an Errored Second. Typically, ESThresh = 1. DSThresh If the number of codeword errors detected within 1 second is greater than or equal to this threshold and less than SESThresh, that second is treated as a Degraded Second. SESThresh If the number of codeword errors detected within a 1-second interval is greater than or equal to this threshold, that second is treated as a Severely Errored Second. CSESThresh Specifies the number of consecutive severely errored seconds that must be detected for the sequence to be treated as one consecutively Severely Errored Second.
Defaults
No default behaviors or values.
Command Modes
Interface configuration
Command History
12.0(7)XR This command was introduced.
Release
Modification
Usage Guidelines
When the radio link is synchronized, the measurement parameters used are:
All link metrics are measured in terms of codewords which are in units (228 bytes) of data transmission over the radio link. Each unit contains user data, error counts, and collation information so that successive codewords are reconstructed at the receiving end into the transmitted data.
 |
Caution Use this command with care. Arbitrary changes will distort the performance metrics reported for the radio link. |
Examples
The following example configures the link so that:
UBR04(config-if)# radio metrics-threshold code-word 3 30 150 4
Related Commands
show interfaces radio slot/port metrics-threshold Shows the thresholds set for link metrics. radio metrics-threshold 1hour Displays the link metrics for a one-hour period. radio metrics-threshold 24hour Displays the link metrics for a twenty-four hour period.
Command
Description
To set threshold values that configure limits on the ES, SES, CSES, and DM to measure how well the radio link is performing over a 24-hour period, use the radio metrics-threshold 24hour interface configuration command. To force the thresholds back to the default values, use the no form of this command.
radio metrics-threshold 24hour ESLimit SESLimit CSESLimit DMLimit
Syntax Description
ESLimit Specifies the number of errored seconds that are detected within the specified time period (24 operational hours) after which the ESLimit minor alarm is generated. SESLimit Specifies the number of codeword severely errored seconds that are detected within the specified time period 24 operational hours) after which the SESLimit minor alarm is generated. CSESLimit Specifies the number of codeword consecutively severely errored seconds that are detected within the specified time period (24 operational hours) after which the CSESLimit minor alarm are generated. DMLimit Specifies the number of codeword degraded minutes that is detected within the specified period (24 operational hours) after which the DMLimit minor error alarm are generated.
Defaults
No default behaviors or values.
Command Modes
Interface configuration
Command History
12.0(7)XR This command was introduced.
Release
Modification
Usage Guidelines
When the radio link is synchronized, the measurement parameters used are:
When these limits are exceeded in a 24-hour period, alarms are generated to notify the user. Minor alarms appear on the console when the specified 24-hour threshold is exceeded.
|
Caution Use this command with care. Arbitrary changes distort the performance metrics reported for the radio link. |
Examples
The following example configures the link alarms so that:
UBR04(config-if)# radio metrics-threshold 24hour 24 36 12 5
Related Commands
show interfaces radio slot/port metrics-threshold Shows the thresholds set for link metrics. radio metrics-threshold code-word Configures thresholds that determine when a second is classified as ES, DS, SES, or CSES for the radio link. radio metrics-threshold 1hour Displays the link metrics for the past one-hour period.
Command
Description
To to configure limits on the ES, SES, CSES, and Degraded Minutes (DM), use the radio metrics-threshold 1hour interface configuration command. To force the thresholds back to the default values, use the no form of this command.
radio metrics-threshold 1hour ESLimit SESLimit CSESLimit DMLimit
Syntax Description
ESLimit Specifies the number of errored seconds that are detected within the specified time period (1 operational hour) after which the ESLimit minor alarm is generated. SESLimit Specifies the number of codeword severely errored seconds that are detected within the specified time period (1 operational hour) after which the SESLimit minor alarm is generated. CSESLimit Specifies the number of codeword consecutively severely errored seconds that are detected within the specified time period (1 operational hour) after which the CSESLimit minor alarm is generated. DMLimit Specifies the number of codeword degraded minutes that are detected within the specified period (1 operational hour) after which the DMLimit minor error alarm is generated.
Defaults
No default behaviors or values.
Command Modes
Interface configuration
Command History
12.0(7)XR This command was introduced.
Release
Modification
Usage Guidelines
When the radio link is synchronized, the measurement parameters used are:
When these limits are exceeded in a 1-hour period, alarms are generated to notify the user. Minor alarms are displayed on the console when the specified 1-hour threshold is exceeded.
|
Caution Use this command with care. Arbitrary changes distort the performance metrics reported for the radio link. |
Examples
The following example configures the link alarms so that:
UBR04(config-if)# radio metrics-threshold 1hour 6 10 3 2
Related Commands
show interfaces radio slot/port metrics-threshold Shows the thresholds set for link metrics. radio metrics-threshold code-word Configures thresholds that determine when a second is classified as ES, DS, SES, or CSES for the radio link. radio metrics-threshold 24hours Displays the link metrics for the past 24 hour period.
Command
Description
To specify the radio operating band and transmit/receive frequencies within the radio operating band, use the radio operating-band interface configuration command. To reset the operating band to the default values, use the no form of this command.
radio operating-band Tx transmit frequency Rx receive frequency
Syntax Description
transmit frequency Positive number in the range 5725.00 MHz to 5825.00 MHz (U-NII) receive frequency Positive number in the range 5725.00 MHz to 5825.00 MHz (U-NII)
Defaults
TBC
Command Modes
Interface configuration
Command History
12.0(7)XR This command was introduced.
Release
Modification
Usage Guidelines
You can enter this command at any time. If the link is up when you enter the command, the command takes effect with the next shut/no shut. If the link is down when you enter the command, the command takes effect with the next no shut.
Use the channel-setup parameters to select the required bandwidth and data throughput before specifying the operating-band.
Transmit and receive frequencies must be consistent with the bandwidth the radio has been configured to operate in using the channel-setup command and must fall within the passband of the duplexer used in the transverter.
See Cisco uBR7200 Series Universal Broadband Router Wireless Modem Card and Subsystem Installation and Configuration for center frequencies for the U-NII band.
For a complete list of channel designations and start, center, and end frequencies, see the Cisco Broadband Fixed Wireless Site Planning Guide.
The transmit frequency on the radio designated as "master" must be identical to the receive frequency on the radio designated as "slave."
|
Note No license is required in the U.S. to operate in the U-NII band. |
Examples
The following example sets center frequencies:
UBR04(config-if)# radio operating-band Tx 2533.00 Rx 2599.00
Related Commands
show running-configuration interface radio Displays the current setting.
Command
Description
To configure the baseline encryption options provided by the wireless modem card, use the radio privacy interface configuration command. To turn off privacy options, use the no form of this command.
radio privacy {enable | auth-wait-time secs | reauth-wait-time secs | auth-grace-time secs | op-wait-time secs | rekey-wait-time secs | tek-grace-time secs | auth-lifetime secs | tek-lifetime secs}
Syntax Description
auth-wait-time The number of seconds the slave radio waits before issuing a new authorization request to the master radio. reauth-wait-time The number of seconds the slave radio waits before issuing a new reauthorization request to the master. auth-grace-time Grace time for an authorization key. The slave radio tries to get a new authorization key beginning auth-grace-time seconds before the authorization key actually expires. op-wait-time Operational wait timeout. rekey-wait-time The amount of time (in seconds) that the slave radio waits before issuing a new request to the master radio for an encryption key. tek-grace-time Grace time for a traffic encryption key (TEK). The slave radio tries to get a new TEK beginning tek-grace-time seconds before the traffic encryption key actually expires. auth-lifetime The lifetime (in seconds) the master radio assigns to an authorization key for the slave radio. tek-lifetime The lifetime (in seconds) assigned to traffic encryption keys by the master radio.
Defaults
Privacy not enabled.
Command Modes
Interface configuration
Command History
12.0(7)XR This command was introduced.
Release
Modification
Usage Guidelines
The radio designated as "master" controls privacy authorization and encryption key distribution. The radio designated as "slave" tracks the master radio's signals. The default is on.
Use the enable option to enable baseline privacy options. Use the other options to configure timeout values. When privacy is enabled, the timeout values determine how long the master or the slave radio waits for either authentication or encryption keys to be revalidated. If this revalidation fails, meaningful communication between master and slave radios is not possible.
|
Note Using baseline privacy has no effect on throughput and only a negligible effect on latency. |
|
Note You can only change these parameters when the radio link is down (shut). |
Examples
The following example configures baseline privacy:
UBR04(config-if)# radio privacy enable
Related Commands
show running-configuration Displays the current settings.
Command
Description
To configure the wireless modem card to use a specified number of receive antennas, use the radio receive-antennas interface configuration command. To set the number of antennas to 1, use the no form of this command.
radio receive-antennas {1 | 2}
Syntax Description
1 | 2 Specifies which antenna to use. Enter 1 (main antenna) or 2 (diversity antenna).
Defaults
Number of antennas 1.
Command Modes
Interface configuration
Command History
12.0(7)XR This command was introduced.
Release
Modification
Usage Guidelines
You can enter this command only when the radio link is down (shut). The command takes effect when the link is again active (no shut). Use the no version of the command to set the number of receive antennas to 1 (the default value).
|
Note Before this command can take effect, the receive antennas and wireless transverters must be available. |
Related Commands
The following example configures the wireless modem card to use two receive antennas:
UBR04(config-if)# radio receive-antennas 2
Related Commands
show running-configuration interface radio Displays the current setting.
Command
Description
To configure a single DSP to send the identified type of output to the serial port, use the radio scope-output privileged EXEC command. To to turn off the serial output, use the no form of this command.
radio scope-output dspId outputType
Syntax Description
dspId {dsprxla (Receive DSP 1a) | dsprx1b (Receive DSP 1b) | dsprx2a (Receive DSP 2a) | dsprx2b (Receive DSP 2b) | dsprx3a (Receive DSP 3a) | dsprx3b (Receive DSP 3b) | outputType {rx-rawburst-ant1-y1n | rx-rawburst-ant1-y2n | rx-spectrum-ant1-y1k | rx-spectrum-ant1-y2k | rx-timedomainchannel-ant1-h1n | rx-timedomainchannel-ant2-h2n | rx-freqdomainchannel-ant1-h1k | rx-freqdomainchannel-ant2-h2k | rx-constellation-zhatk | tx-codec-input | tx-ifft-input | tx-round-output | sync-burst-timecost-func | sync-freq-offset-costfunc | sync-pwrsbtcffocf | sync-fll-freq-corelation | sync-fll-train-tone-corelation | sync-fll-fft-spectrum} slot/port The slot and port address.
dsptx1 (Transmit DSP 1) | dsptx2 (Transmit DSP 2)}
Defaults
No default behavior or values.
Command Modes
Privileged EXEC
Command History
12.0(7)XR This command was introduced.
Release
Modification
Usage Guidelines
An oscilloscope can be connected to the serial port to analyze the output of the DSP.
You can gather the output of only one DSP at a time.
Examples
The following example sends an output of type rx-timedomainchannel-ant2-h2n to the serial port:
UBR04# radio scope-output dsprx1a RxTimeDomainChannelAnt2H2n
Related Commands
show interfaces radio slot/port scope-output Displays the attribute being directed to the scope port.
Command
Description
To test the memory and hardware integrity of the wireless modem card, use the radio self-test interface configuration command. To configure a restart of the link without executing self-tests, use the no form of this command.
radio self-test [enable]
Syntax Description
enable (Optional) causes execution of self-tests each time the card is initiated.
Defaults
No default behavior or values.
Command Modes
Interface configuration
Command History
12.0(7)XR This command was introduced.
Release
Modification
Usage Guidelines
Use the enable option to execute self-tests each time the card is initiated (no shut). Use the command without the enable option to perform a self-test only on the first no shut after initiation. Each time the test is performed, the results appear on the console.
Examples
The following example shows the configuration command used to download and execute self-tests each time the modem card is enabled:
UBR04(config-if)# radio self-test enable
Related Commands
show running-configuration interface radio Displays the current settings.
Command
Description
To to create a snapshot specification on the modem card, use the radio snapshot privileged configuration command. To delete a specification and its associated data, use the no form of this command.
radio snapshot dspId snapshotType
Syntax Description
dspId {dsprxla (Receive DSP 1a) | dsprx1b (Receive DSP 1b) | dsprx2a (Receive DSP 2a) | dsprx2b (Receive DSP 2b) | dsprx3a (Receive DSP 3a) | dsprx3b (Receive DSP 3b) | snapshotType Unsigned number. You can request up to four different snapshot types at once. When you request more than one snapshot is in a command, all snapshots are captured from the same DSP. See the snapshot type definitions below. rx-rawburst-ant1-y1n (0x01) Represents a snapshot of the received signal for RF resource 1. For every sample, the real and imaginary components are captured. rx-rawburst-ant2-y2n (0x02) Represents a snapshot of the received signal for RF resource 2. For every sample, the real and imaginary components are captured. rx-spectrum-ant1-y1k (0x04) Represents a snapshot of the spectrum of the received signal for RF resource 1. For every sample, the real and imaginary components are captured. rx-spectrum-ant2-y2k (0x08) Represents a snapshot of the spectrum of the received signal for RF resource 2. For every sample, the real and imaginary components are captured. rx-timedomainchannel-ant1-halon (0x10) Represents a snapshot of the time domain channel for RF resource 1. For every sample, the real and imaginary components are captured.
dsptx1 (Transmit DSP 1) | dsptx2 (Transmit DSP 2)}
Units: (I, q)
Value: 32-bit quantities
Units: (I, q)
Value: 32-bit quantities
Units: (I, q)
Value: 32-bit quantities
Units: (I, q)
Value: 32-bit quantities
Units: (I, q)
Value: 32-bit quantities
rx-timedomainchannel-ant2-h2n (0x20) | Represents a snapshot of the time domain channel for RF resource 2. For every sample, the real and imaginary components are captured. |
rx-freqdomainchannel-ant1-hlk (0x40) | Represents a snapshot of the frequency domain channel for RF resource 1. For every sample, the real and imaginary components are captured. |
rx-freqdomainchannel-ant2-h2k (0x80) | Represents a snapshot of the frequency domain channel for RF resource 2. For every sample, the real and imaginary components are captured. |
rx-constellation-zhatk (0x100) | Represents a snapshot of the soft decisions. For every sample, the real and imaginary components are captured. |
tx-codec-input (0x200) | Represents a snapshot of input values to the Tx Code. |
tx-ifft-input (0x400) | Represents a snapshot of the IFFT signal for the transmitted data. For every sample, the real and imaginary components are captured. |
tx-round-output (0x800) | Represents a snapshot of the Rounded Constellation signal for the transmitted data. For every sample, the real and imaginary components are captured. |
sync-burst-timecost-func (0x1000) | Represents the timing cost function for Sync bursts. |
sync-freq-offset-costfunc (0x2000) | Represents a snapshot of the frequency offsets. For every sample, the real and imaginary components are captured. |
sync-pwrsbtcffocf (0x4000) | Represents a snapshot of Sync power burst. For every sample, the real and imaginary components are captured. |
sync-fll-freq-correlation (0x8000) | Represents a snapshot of Frequency correlation. For every sample, the real and imaginary components are captured. |
sync-fll-train-tone-correlation (0x10000) | Represents a snapshot of Frequency locked loops, Training tone correlation. For every sample, the real and imaginary components are captured. |
sync-fll-fft-spectrum (0x20000) | Represents a snapshot of Frequency locked loop, FFT Spectrum. For every sample, the real and imaginary components are captured. |
Defaults
No default behavior or values.
Command Modes
Privileged configuration
Command History
12.0(7)XR This command was introduced.
Release
Modification
Usage Guidelines
A snapshot is a specified amount of data captured from the wireless modem card.
When you issue a snapshot request, up to four simultaneous radio signal attributes can be captured. The four attributes are specified by adding the attribute numbers for up to four of the snapshot types identified below.
|
Note Do not mix the Tx and Rx types. You can mix Rx and Sync types. When a radio snapshot command is issued, you can request up to four signal attributes at once; one from each set. |
Related Commands
show interfaces radio snapshot Displays configured snapshot information. show interfaces radio snapdata Displays the data captured for the snapshot specification radio interface radio snapcapture Creates a snapshot on the specified DSP. radio interface radio snapclear Clears the snapshot data on the specified DSP.
Command
Description
To configure a threshold event specification, use the radio threshold interface configuration command. To terminate the event-threshold setup, use the no form of this command.
radio threshold threshParam antennaNum [dsp dspId] threshType threshValue repeatTime clearTime
Syntax Description
threshParam {in | inr | constVariance | timingOffset | freqOffset | syncStatus | receivedPower | gainSettingsIF | gainSettingsRF | totalGain} in (Interference + Noise) The interference plus noise power levels are computed by the hardware on a burst-by-burst basis. inr (Interference + Noise Ratio) The ratio of the interference plus noise power levels captured by the first antenna to the second antenna on a burst-by-burst basis. This value is specified as a log to base 2 number. constVariance (Constellation Variance) The average energy of the constellation error signal - the error between the received (noisy) constellation symbol and the nearest ideal constellation symbol. Constellation Variance is a measure of the Signal to Interference plus Noise ratio (SINR) for that tone. On a single antenna system, it represents (SINR)-1. On a dual antenna system, it represents a composite value providing (SINR)-1 after antenna combining. timingOffset Represents the timing delay variations detected in the radio link. freqOffset Represents the carrier frequency offset between the slave radio and the master radio. syncStatus Represents the synchronization status. receivedPower A measure of the analog signal power received by the radio system on a burst-by-burst basis. gainSettingsIF Represents the IF attenuation value commanded by the automatic gain control loop. This can be captured for each antenna and for the intermediate frequency (IF) module. gainSettingsRF Represents the RF attenuation value commanded by the automatic gain control loop. This can be captured for each antenna and for the radio frequency (RF) modules. totalGain Represents the total attenuation commanded by the automatic gain control loop. This can be captured for each antenna. antennaNum Enter either 1 (main antenna) or 2 (diversity antenna). dspId {dsprx1a (Receive DSP 1a) | dsprx1b (Receive DSP 1b) | dsprx2a (Receive DSP 2a) | dsprx2b (Receive DSP2b) | dsprx3a (Receive DSP 3a) | dsprx3b (Receive DSP 3b)} threshType {highThreshold | lowThreshold | upChange | downChange | posCrossing | negCrossing} highThreshold The upper limit for the threshParam being monitored. lowThreshold The lower limit for the threshParam being monitored. upChange The positive change limit allowed for the threshParam being monitored. downChange The negative change limit allowed for the threshParam being monitored. posCrossing The limit that applies only when the threshParam is increasing in value. negCrossing The limit that applies only when the threshParam is decreasing in value. threshValue A 32-bit integral value repeatTime When radio signals are monitored, they can oscillate across a specified threshold (such as highThreshold) very rapidly. In such a case, an event is generated for each crossing of the threshold, which could flood the system. The repeatTime parameter specifies the amount of time (in seconds) the system waits before another event of the same type is generated. clearTime When radio signals oscillate across a threshold, this parameter identifies when the signal stabilizes. The clearTime parameter specifies how many seconds the radio signal must stay below a threshold (after crossing it once) before the system generates the clear event.
Note This parameter is available for a dual antenna system only.
Defaults
No default behavior or values.
Command Modes
Interface configuration
Command History
12.0(7)XR This command was introduced.
Release
Modification
Usage Guidelines
When the specified threshold is crossed, an event of type threshParam eventType is generated and the event is logged to the console.
Only one threshold can be defined for each of the identified threshParam threshType [dsp dspId] combination. When a threshold is crossed, the threshParam threshType [dsp dspId] combination identifies the threshold specification that caused the event.
For every threshold defined, antennaNum is conditional. Antenna number is applicable for the threshParam attributes in, receivedPower, gainSettingsIf, gainSettingsRF, and totalGain.
|
Note If an antenna number is used when a threshold is created, it must also be specified when the threshold is deleted. |
For each event, the threshParam [dsp dspId] threshType eventType is output identifying the threshold crossed.
The no radio threshold command requires the threshParam, threshType, and [dsp dspId] attributes.
Examples
The following command sequence sets up a threshold for totalGain. When the totalGain for the system on antenna2 falls below 70, the eventSet event type is generated.
UBR04(config-if)# radio threshold totalGain 2 lowThreshold 70
Related Commands
show interfaces radio thresholds Displays the current threshold specifications.
Command
Description
To configure a timeline collection specification with the software, use the radio timeline privileged EXEC command. To delete a timeline, use the no form of this command.
radio timeline statParam antenna_num [dsp dspId] tlSize [decimationFactor df] [presummationShift pss] [print {on | off}] [tone {circular | average | number tone-number] [trigger threshParams threshType (antenna_num) postTrigBufMgt]
Syntax Description
statParam {in | inr | constVariance | timingOffset | freqOffset | syncStatus | receivedPower | gainSettingsIF | gainSettingsRF} in (Interference + Noise) The interference plus noise power levels are computed by the hardware on a burst-by-burst basis. inr (Interference + Noise Ratio) The ratio of the interference plus noise power levels captured by the first antenna to the second antenna on a burst-by-burst basis. This value is specified as a log to base 2 number. constVariance (Constellation Variance) The average energy of the constellation error signal - the error between the received (noisy) constellation symbol and the nearest ideal constellation symbol. Constellation Variance is a measure of the Signal to Interference plus Noise ratio (SINR) for that tone. On a single antenna system, the error represents (SINR)-1. On a dual antenna system, it represents (SINR)-1 after antenna combining. timingOffset Represents the timing delay variations detected in the radio link. freqOffset This represents the carrier frequency offset between the slave radio and the master radio. syncStatus Represents the synchronization status. receivedPower A measure of the analog signal power received by the radio system on a burst-by-burst basis. gainSettingsIF Represents the IF attenuation value commanded by the automatic gain control loop. This can be captured for each antenna and for the intermediate frequency (IF) module. gainSettingsRF Represents the RF attenuation value commanded by the automatic gain control loop. This can be captured for each antenna and for the radio frequency (RF) modules. totalGain Represents the total attenuation commanded by the automatic gain control loop. This can be captured for each antenna. dspId {dsprx1a (Receive DSP 1a) | dsprx1b (Receive DSP 1b) | dsprx2a (Receive DSP 2a) | dsprx2b (Receive DSP2b) | dsprx3a (Receive DSP 3a) | dsprx3b (Receive DSP 3b)} The DSP on which to collect the timeline data. antenna_num Enter 1 (main antenna) or 2 (diversity antenna). The antenna for which the timeline data is collected. tlSize Positive number representing the number of values to collect. decimationFactor The rate at which data is received is high, so retrieving every successive data sample provides little information (due to memory limitations). The decimation factor specifies how many successive data samples are added together and reported as one data sample. If the decimation factor is not specified, every successive data sample is reported. df {0 . . 231} presummationShift If decimationFactor is specified, then successive data samples are added. This can potentially cause an overflow. The presummationShift value specifies the number of bits by which the data sample is right-shifted before it is added. Specifying a presummationShift value results in less precise individual data samples but provides a mechanism to analyze the behavior over long periods of time. pss (0 . . 32) print {on | off} Specifies whether or not the collected values are printed out when the collection completes. The default is on. tone {circular | average | number tone-number} Every burst of signal data contains samples from N frequency tones. This parameter identifies which tones are used. circular Implies successive data samples should use successive frequency tones. average Implies successive data samples should average the burst data over all the N frequencies and then use that value. number Specifies that data from a particular frequency in the burst are reported. tone-number for in and inr for constVariance trigger Specifies when the collection has to be stopped. The threshParam threshType antenna_num parameters uniquely identify a threshold specification. When this threshold is reached, the timeline is stopped and the data collected. threshParam {in | inr | constVariance | timingOffset | freqOffset | syncStatus | receivedPower | gainSettingsIF | gainSettingsRF} threshType {highThreshold | lowThreshold | upChange | downChange | posCrossing | negCrossing} highThreshold An upper limit for the threshParam being monitored. lowThreshold A lower limit for the threshParam being monitored. upChange The positive change limit allowed for the threshParam being monitored. downChange The negative change limit allowed for the threshParam being monitored. posCrossing The limit that applies only when the threshParam increases in value. negCrossing The limit that applies only when the threshParam decreases in value. postTrigBufMgt Specifies the position of the trigger in the data collected. If the position is 1, then most of the data collected before the trigger is returned. If the position is 2, most of the data returned is captured after the occurrence of the trigger.
Note This parameter is available for a dual antenna system only.
{ {0 . . 27} for 12 MHz high, 6 MHz high }
{ {0 . . 33 } otherwise }
{ {0 . . 216} for 12 MHz high }
{ {0 . . 198} for 12 MHz med, low }
{ {0 . . 108 } for 6 MHz high }
{ {0 . . 99 } for 6 MHz med, low }
Defaults
No default behavior or values.
Command Modes
Privileged EXEC
Command History
12.0(7)XR This command was introduced.
Release
Modification
Usage Guidelines
A timeline is a sequence of data values collected for a specified attribute. The amount of data collected is controlled by the tlSize parameter. The maximum size is determined by the hardware memory size.
Collection starts as soon as the command succeeds and continues until the trigger occurs or the timelineStop command is executed.
For every timeline defined, antenna_num and tone are conditional. The antenna_num is required for the attributes in, receivedPower, GainSettingsIF, gainSettingsRF, and totalGain. The tone can be optionally specified for the attributes in, inr, and constVariance.
Up to 1024 32-bit words are available for all timeline parameters on a single DSP. Each timeline requires (tlsize+1) * 2 words. The attributes in in, inr, and constVariance can be captured on any DSP, while the others can be captured only on certain DSPs. Distributing timeline requests across DSPs provides better memory utilization.
Examples
The following example configures a timeline specification. The collection process starts as soon as the command succeeds. The inr parameter is monitored. A total of 640 values is collected.
Of the N tones in a burst, the average value of all the tones (for the burst) is retrieved as one data sample. Each data sample is right shifted by 2 bits. Twenty successive (right-shifted) data samples are added together and reported as one value (of the 640 values in total).
When the threshold inr lowThreshold 2 is reached, the collection stops and the results are printed.
UBR04#radio timeline inr 640 dec 20 pre 2 tone average trigger inr
lowThreshold 2
Related Commands
radio interface radio timelineStart Starts a stopped timeline specification. radio interface radio timelineStop Stops a running timeline specification. show interfaces radio tldata Displays timeline data for the specified card. show interfaces radio tlspec Displays the details of the timeline specification.
Command
Description
To configure the transverter to transmit the specified amount of power (in dBm) when in operation, use the radio transmit-power interface configuration command. To disable, use the no form of this command.
radio transmit-power power
Syntax Description
power Positive number representing power stated in dBm. Transmit power range for U-NII is between 4 and 24 dBm.
Defaults
No default behavior or values.
Command Modes
Interface configuration
Command History
12.0(7)XR This command was introduced. 12.1(1)T Transmit power range modified.
Release
Modification
Usage Guidelines
Maximum transmission power is limited by the capabilities of the transverter. In addition, your country's telecommunications authority (the FCC in the United States) regulates the maximum power and/or the EIRP in the U-NII bands. It is the responsibility of the installer and operator to comply with the relevant regulations.
To support the maximum number of users in an area, keep the power as low as possible while maintaining sufficient margin and performance. See Cisco Broadband Fixed Wireless Site Planning Guide for additional information.
Examples
The following example sets the transmit power to +25 dBm:
UBR04(config-if)# radio transmit-power 25
Related Commands
show running-configuration interface radio Displays the current setting.
Command
Description
To display all or a subset of attributes of a particular modem card, use the show controllers radio privileged EXEC command.
show controllers radio slot number/port number [{if | rf | fir | codec | dsp | arq | pci | phy | driver}]
Syntax Description
slot number Positive integer representing the Cisco uBR7200 series slot number. port number Positive integer representing the port number on that slot. if (version, freq, register1): rf (version, freq, power) fir (version, firThresh,) codec (version, rsDecodeErrThresh, rdDecodeErrBytes) dsp (version) arq (version, arqThresh) pci (version) phy (version)
Defaults
No default behavior or values.
Command Modes
Privileged EXEC
Command History
12.0(7)XR This command was introduced.
Release
Modification
Usage Guidelines
If you do not specify any option, all the hardware subsystem(s) information appears. Actual output parameters depend on the hardware and implementation.
Examples
The following example shows the output received when the pci option is specified for the modem card in slot number 3, port number 0.
UBR04# show controllers radio 3/0 pci
Interface Radio 3/0
Hardware is CW Radio Point-to-Point Line Card
throttled 0 enabled 0 disabled 0
Rx: spurious 0 framing_err 0 no_buffer 0, pause_no_err_ints 0
no_enqueue 0 no_stp 0 no_enp 0
Tx: full 0 drop 0
rx ring entries 32 tx ring entries 128
Rx ring 0x4B05A0C0 shadow 0x61399C60 head 2
Normal Latency Tx ring 0x4B05A680 shadow 0x6139A1C0 head 0 tail 0 count 0
Low Latency Tx ring 0x4B05A220 shadow 0x61399D50 head 3 tail 3 count 0
PCI Configuration Registers
Device/Vendor IDs - 0x00141137
Command/Status - 0x02000086
Latency Timer - 0x0000FF00
Base Address 0 - 0x4E000000
Max Lat - 0x000001FF
PCI Interface FPGA
dmac_control - 0x00440002
dmac_status - 0x00004000
dmac_int_status - 0x99800001
dmac_int_enable - 0x66710FF8
dmac_tx0_ring_base - 0x4B05A220
dmac_tx1_ring_base - 0x4B05A680
dmac_rx_ring_base - 0x4B05A0C0
dmac_configuration - 0x66040303
local_bus_error_status - 0x00000000
local_bus_error_address - 0x010C0000
local_bus_reset - 0x00000000
fpga_configuration_control - 0x00000000
fpga_configuration_status - 0x000000FF
To see the current ARQ configuration on the wireless modem card, use the show interfaces radio arq privileged EXEC command.
show interfaces radio slot/port arq
Syntax Description
slot/port The slot and port address.
Defaults
No default behavior or values.
Command Modes
Privileged EXEC
Command History
12.0(7)XR This command was introduced.
Release
Modification
Usage Guidelines
If you don't specify optional parameters, then all the timeline specifications on the modem card are displayed. If you only specify the statParam antenna_num combination, then the configuration setup on the default appears. If you specify the [dsp dspId] parameter, then the configurations on that DSP appears.
Examples
The following example displays the ARQ configuration for the modem card in slot 3, port 0:
UBR04# show interfaces radio 3/0 arq
ARQ State = on
Data Latency = 20 ms
Voice Latency = 20 ms
Maximum ARQ Bandwidth Overhead = 12.50%
Typical Bit Rate = 10845152 bits/sec
Minimum Bit Rate = 9488600 bits/sec
Burst Size = 16 codewords
Maximum Latency Jitter = 2679 usec
The following table describes the fields shown in the show interfaces radio arq display.
|
|
|---|---|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Related Commands
radio arq Configures Automatic Repeat Query.
Command
Description
To see the collected histogram data for the identified histogram specification, use the show interfaces radio histdata privileged EXEC command.
show interfaces radio slot/port histdata statparam antenna_num dsp dspnum
Syntax Description
slot Positive integer representing the Cisco uBR7200 series slot number. port Positive integer representing the port number on that slot. statParam {in | inr | constVariance | timingOffset | freqOffset | syncStatus | receivedPower | gainSettingsIF | gainSettingsRF | totalGain | codewordError} Data for the radio attribute is to be collected as a histogram. in (Interference + Noise) The interference plus noise power levels are computed by the hardware on a burst-by-burst basis. inr (Interference + Noise Ratio) The ratio of the interference plus noise power levels captured by the first antenna to the second antenna on a burst-by-burst basis. This value is specified as a log to base 2 number. constVariance (Constellation Variance) The average energy of the constellation error signal - the error between the received (noisy) constellation symbol and the nearest ideal constellation symbol. Constellation Variance is a measure of the Signal to Interference + Noise ratio (SINR) for that tone. On a single antenna system, the variance represents (SINR)-1. On a dual antenna system, the variance represents a composite value providing (SINR)-1. timingOffset Represents the timing delay variations detected in the radio link. freqOffset Represents the carrier frequency offset between the slave radio and the master radio. syncStatus Represents the synchronization status. receivedPower A measure of the analog signal power received by the radio system on a burst-by-burst basis. gainSettingsIF Represents the IF attenuation value commanded by the automatic gain control loop. This value can be captured for each antenna and for the intermediate frequency (IF) module. gainSettingsRF Represents the RF attenuation value commanded by the automatic gain control loop. This value can be captured for each antenna and for the radio frequency (RF) module. totalGain Represents the total attenuation commanded by the automatic gain control loop. This value can be captured for each antenna. antenna_num Enter 1 (main antenna) or 2 (diversity antenna). dspnum The DSP number.
Note If statParam is specified, antenna_num is conditionally required.
Note This parameter is available for a dual antenna system only.
Note For every threshold defined, antenna_num is conditional. The attributes in, receivedPower, GainSettingsIF, gainSettingsRF, and totalGain are applicable for antenna_num.
Note If you don't specify the DSP number, the specification on the default DSP appears.
Defaults
No default behavior or values.
Command Modes
Privileged EXEC
Command History
12.0(7)XR This command was introduced.
Release
Modification
Usage Guidelines
The values appear as a BinID:Value pair. BinId represents the sample value contained in that bin. Value represents the count in the histogram bin.
Examples
The following example shows the command used to display the histogram data for the histogram configured on the modem card in slot 6, port 0 of the uBR7200 series router for receive DSP 1a.
UBR04#show interfaces radio 6/0 histdata inr dsp dsprx1aHistogram 4/1/8 [*=100] min=-2 avg=0157 0=<0 ** 137 0=<1 ** 115 1=<2 ** 44 2=<MAX *
Related Commands
show interfaces radio histspec Displays the details of the histogram specifications currently configured.
Command
Description
To see the details of the histogram specifications currently configured, use the show interfaces radio histspec privileged EXEC command.
show interfaces radio slot/port histspec [statParam antenna_num [dsp dspnum]]
Syntax Description
slot Positive integer representing the Cisco uBR7200 series slot number. port Positive integer representing the port number on that slot. statParam {in | inr | constVariance | timingOffset | freqOffset | syncStatus | receivedPower | gainSettingsIF | gainSettingsRF | totalGain} Data for the radio attribute is to be collected as a histogram. in (Interference + Noise) The interference plus noise power levels are computed by the hardware on a burst-by-burst basis. inr (Interference + Noise Ratio) The ratio of the interference plus noise power levels captured by the first antenna to the second antenna on a burst-by-burst basis. This value is specified as a log to base 2 number. constVariance (Constellation Variance) The average energy of the constellation error signal - the error between the received (noisy) constellation symbol and the nearest ideal constellation symbol. Constellation Variance is a measure of the Signal to Interference plus Noise ratio (SINR) for that tone. On a single antenna system, the value represents (SINR)-1. On a dual antenna system, the value represents a composite value providing (SINR)-1. timingOffset Represents the time delay variations detected in the radio link. freqOffset Represents the carrier frequency offset between the slave radio and the master radio. syncStatus Represents the synchronization status. receivedPower A measure of the analog signal power received by the radio system on a burst-by-burst basis. gainSettingsIF Represents the IF attenuation value commanded by the automatic gain control loop. This value can be captured for each antenna and for the intermediate frequency (IF) module. gainSettingsRF Represents the RF attenuation value commanded by the automatic gain control loop. This value can be captured for each antenna and for the radio frequency (RF) module. totalGain Represents the total attenuation commanded by the automatic gain control loop. This value can be captured for each antenna. antenna_num Enter 1 (main antenna) or 2 (diversity antenna). dspnum The DSP number.
Note If you specify the statParam, antenna_num is conditionally required.
Note This parameter is available for a dual antenna system only.
Note For every histogram defined, antenna_num is conditional. The antenna_num is required for attributes in, receivedPower, GainSettingsIF, gainSettingsRF, and totalGain.
Note If you don't specify the DSP number, the specification on the default DSP appears.
Defaults
No default behavior or values.
Command Modes
Privileged EXEC
Command History
12.0(7)XR This command was introduced.
Release
Modification
Usage Guidelines
If you don't specify the optional parameters, all histogram specifications on the modem card appear.
Examples
The following example shows details of the histogram Constellation Variance specification configured for the modem card in slot 3, port 0 of the uBR7200 series router:
UBR04# show interfaces radio 3/0 histspec constVariance
Class constVariance
Start Bin Value 0
Bin Delta 4
Number of Bins 100
Update Rate 10
Collection duration 20
Bit Shift 0
Tone Selection average
Dsp Number dsrx1a
Index 9
Periodic Sum false
Default Hist false
Display status on
Histogram Status captured
Related Commands
show interfaces radio histdata Displays the collected histogram data for the identified histogram specification.
Command
Description
To see details of the images to be downloaded on a single chip or on all chips, use the show interfaces radio imagehdr privileged EXEC command.
show interfaces radio slot/port imagehdr [chip chipname [current | operational]]
Syntax Description
slot/port The slot and port address. chipName A character string identifying a chip. current Display the image header (details) for the image currently loaded on the chip. operational Display the image header for the image that will be loaded on the chip for the current configuration.
Defaults
No default behavior or values.
Command Modes
Privileged EXEC
Command History
12.0(7)XR This command was introduced.
Release
Modification
Usage Guidelines
If you specify a particular chip, the details of the image to be loaded on that chip appear. If you don't specify a chip name, the current radio configuration is retrieved for every chip on the modem card. All the images in the repository are compared. The image that provides the closest match in capability is selected, and the details of that image appears.
Examples
The following example displays the image details of the chip named dsp1a currently loaded on the chip on the modem card in slot 3, port 0:
UBR04# show interfaces radio 3/0 imagehdr dsp1a current
To display the attribute being sent to the scope port, use the show interfaces radio scope-output privileged EXEC command.
show interfaces radio slot/port scope-output
Syntax Description
slot/port The slot and port address.
Defaults
No default behavior or values.
Command Modes
Privileged EXEC
Command History
12.0(7)XR This command was introduced.
Release
Modification
Related Commands
radio scope-output Configures the specified DSP to send the specified output to the serial port.
Command
Description
To display snapdata information, use the show interfaces radio snapdata privileged EXEC command.
show interfaces radio slot/port snapdata dspId
Syntax Description
slot/port The slot and port address. dspId Specifies the DSP number.
Defaults
No default behavior or values.
Command Modes
Privileged EXEC
Command History
12.0(7)XR This command was introduced.
Release
Modification
Examples
The following example displays snapdata information on dsp1a on the modem card in slot 3, port 0:
UBR04# show interfaces radio 3/0 snapdata dsp1a
Related Commands
radio snapshot Creates a snapshot specification. radio interface radio snapclear Clears the data collected for the specified snapshot.
Command
Description
To display snapshot information, use the show interfaces radio snapshot privileged EXEC command.
show interfaces radio slot/port snapshot dspId
Syntax Description
slot/port The slot and port address. dspId Specifies the DSP number.
Defaults
No default behavior or values.
Command Modes
Privileged EXEC
Command History
12.0(7)XR This command was introduced.
Release
Modification
Examples
The following example displays snapshot information for dsp dsp1a on the modem card in slot 3, port 0:
UBR04#show interfaces radio 3/0 snapshot dsp1a
Related Commands
radio snapshot Creates a snapshot specification. radio interface radio snapclear Clears the data collected for the specified snapshot. show interfaces radio snapdata Displays the data captured for the snapshot specification.
Command
Description
To display the set of currently configured thresholds on the modem card on the specified DSP, use the show interfaces radio privileged EXEC command.
show interfaces radio slot/port thresholds [dspNum]
Syntax Description
slot/port The slot and port address. dspNum The DSP number.
Defaults
No default behavior or values.
Command Modes
privileged EXEC
Command History
12.0(7)XR This command was introduced.
Release
Modification
Usage Guidelines
If dspNum is not specified, the thresholds for DSP 3 appear.
Examples
The following example displays the set of currently configured thresholds for the modem card in slot 6, port 0 for the Receive DSP 1b:
UBR04#show interfaces radio 6/0 thresholds dsp dsprx1b Threshold Attribute in
Threshold Type downChange
Antenna Id 2
Threshold Value 200
Threshold Repeat Time 5
Threshold Clear Time 8
Threshold DSP Number dsprx1b Index 2 Default Threshold false
Related Commands
radio threshold Configures a threshold event specification
Command
Description
To display the timeline data collected for the identified specifications, use the show interfaces radio ltdata privileged EXEC command.
show interfaces radio slot/port tldata [statParam antenna_num [dsp dspId]]
Syntax Description
slot/port The slot and port address. statParam {in | inr | constVariance | timingOffset | freqOffset | syncStatus | receivedPower | gainSettingsIF | gainSettingsRF | totalGain} Data for the radio attribute is to be collected as a histogram. antenna_num Enter 1 (main antenna) or 2 (diversity antenna). dsp dspId {dsprxla (Receive DSP 1a) | dsprx1b (Receive DSP 1b) | dsprx2a (Receive DSP 2a) | dsprx2b (Receive DSP 2b) | dsprx3a (Receive DSP 3a) | dsprx3b (Receive DSP 3b) |
dsptx1 (Transmit DSP 1) | dsptx2 (Transmit DSP 2)}
Defaults
No default behavior or values.
Command Modes
privileged EXEC
Command History
12.0(7)XR This command was introduced.
Release
Modification
Usage Guidelines
If you don't specify optional parameters, then all the timeline specifications on the modem card appear. If you only the statParam antenna_num combination, then the configuration setup on the default appears. If you specify the [dsp dspId] parameter, then the configurations on that DSP appears.
Examples
The following example displays the timeline inr data for the modem card installed in slot 3, port 0 of the uBR7200 series router:
UBR04# show interfaces radio 3/0 tldata inr
Number of Points Captured=100 Trigger Location=54
0 :0000 0000 0000 0000 0000 0000 0000 0000 0000 0000
10 :0000 0000 0000 0000 0000 0000 0000 0000 0000 0000
20 :0000 0000 0000 0000 0000 0000 0000 0000 0000 0000
30 :0000 0000 0000 0000 0000 0000 0000 0000 0000 0000
40 :0000 0000 0000 0000 0000 0000 0000 0000 0000 0000
50 :FFFFFFFF FFFFFFFF 0000 0000 0000 0000 0000 0001 FFFFFFFF FFFFFFFF
60 :0000 0002 FFFFFFFF FFFFFFFF 0000 0001 0000 0000 0000 0000
70 :0000 0000 0000 0001 FFFFFFFF FFFFFFFF 0000 0000 0000 0001
80 :FFFFFFFF FFFFFFFF FFFFFFFF FFFFFFFF 0000 0002 FFFFFFFF FFFFFFFF 0000 0002
90 :FFFFFFFF FFFFFFFF 0000 0000 0000 0001 FFFFFFFF FFFFFFFF 0000 0000
Related Commands
radio timeline Configures a timeline collection specification. radio interface radio timelineStart Starts a stopped timeline specification. radio interface radio timelineStop Stops a running timeline specification. show interfaces radio tlspec Displays the details of the timeline specification.
Command
Description
To display the details of the currently configured timeline specifications, use the show interfaces radio tlspec privileged EXEC command.
show interfaces radio slot/port tlspec [statParam antenna_num [dsp dspId]]
Syntax Description
slot/port The slot and port address. statParam {in | inr | constVariance | timingOffset | freqOffset | syncStatus | receivedPower | gainSettingsIF | gainSettingsRF | totalGain} Data for the radio attribute whose data is to be collected as a histogram. antenna_num Enter 1 (main antenna) or 2 (diversity antenna). dsp dspId {dsprxla (Receive DSP 1a) | dsprx1b (Receive DSP 1b) | dsprx2a (Receive DSP 2a) | dsprx2b (Receive DSP 2b) | dsprx3a (Receive DSP 3a) | dsprx3b (Receive DSP 3b) |
dsptx1 (Transmit DSP 1) | dsptx2 (Transmit DSP 2)}
Defaults
No default behavior or values.
Command Modes
Privileged EXEC
Command History
12.0(7)XR This command was introduced.
Release
Modification
Usage Guidelines
If you don't specify optional parameters, then all the timeline specifications on the modem card appear. If the statParam antenna_num combination only is specified, then the configuration setup on the default will be displayed. If you specify the [dsp dspId] parameter is specified, then the configurations on that DSP appears.
Examples
The following example shows the inr timeline specification configured for the modem card in port 3, slot 0 of the uBR7200 series router:
UBR04# show interfaces radio 3/0 tlspec inr
Class inr
Resource Id 1
Buffer size 50
Number of buffers 20
Collection method 30
Tone Selection average
Stop threshold attribute in
Stop threshold type downChange
Stop antenna number 1
Print options off
Dsp Number 3
Default T1 false
Related Commands
radio timeline Configures a timeline collection specification. radio interface radio timelineStart Starts a stopped timeline specification. radio interface radio timelineStop Stops a running timeline specification. show interfaces radio tldata Displays timeline data for the specified card.
Command
Description
To show the protocol-specific list of images in the repository, use the show radio repository privileged EXEC command.
show radio repository [header] [protocol]
Syntax Description
header Image header details associated with the list of images will also appear. protocol {mem | tftp | flash}
Defaults
No default behavior or values.
Command Modes
Privileged EXEC
Command History
12.0(7)XR This command was introduced.
Release
Modification
Usage Guidelines
The repository is a list of current configuration images. When the modem card is initiated (no shut), this list is searched and the correct image downloaded. Privileged configuration access is required.
Examples
The following example shows a list of images related to memory:
UBR04# show radio repository mem
mem:/MyMemImages/dsp1Dual.img
mem:/MyMemImages/dsp2Dual.img
mem:/MyMemImages/dsp1Single.img
Related Commands
radio image-add Adds images to the repository. radio image-move Moves the specified image to the beginning of the repository.
Command
Description
To shut down the radio link, use the shut interface configuration command. To reinstate the radio link, use the no form of this command.
shutSyntax Description
This command has no keywords or arguments.
Defaults
No default behavior or values.
Command Modes
Interface configuration
Command History
12.0(7)XR This command was introduced.
Release
Modification
Usage Guidelines
The state of the link appears on the console.
Examples
The following example shuts down the radio link:
UBR04(config-if)# shut
To display debug messages for the radio link, use the debug radio EXEC command. To turn off debugging, use the no form of this command.
debug radio {lm-log | messages | phy}
Syntax Description
lm_log log [verbose] phy {radioLog | cwrLog} radioLog radio slot/port subModule slot Positive integer representing the Cisco uBR7200 series slot number. port Positive integer representing the port number on that slot. subModule {cli | gal | snmp} logLevel cli Tracing the radio interface CLI commands. gal Tracing the GAL module. snmp Tracing the radio SNMP module. logLevel Acceptable values are: {all | controlFlow | dataFlow | validation | verbose} cwrLog cwrLog modName modName Name of the module.
Defaults
No default behavior or values.
Command History
12.0(7)XR This command was introduced.
Release
Modification
Examples
Various logLevels determine what and how much debug log output is generated.
UBR04# debug radio phy radio 3/0 snmp verbose
This command causes various physical layer entities to log debug output:
UBR04(config-if)# debug radio phy cwrLog modName
Related Commands
show debug Displays current debug settings.
Command
Description
Posted: Mon Oct 2 16:39:00 PDT 2000
Copyright 1989-2000©Cisco Systems Inc.