Table of Contents

scheduler allocate
scope
scope map
scope mode
scrambling
segment-target
service-category
sgcp
sgcp call-agent
sgcp graceful-shutdown
sgcp request retries
sgcp request timeout
slip
snmp-server enable traps
sonet
sonet overhead
sonet report
sonet threshold
sonet tx-ais on-rx-defect
statistics
status
summary-address
sync config (Catalyst 8540 MSR)

S Commands

The commands shown in this chapter apply to the Catalyst 8540 MSR, Catalyst 8510 MSR, and LightStream 1010 ATM switch routers. Where an entire command or certain attributes of a command have values specific to a particular switch or switch router, an exception is indicated by the following callouts:

• Catalyst 8540 MSR

• Catalyst 8510 MSR and LightStream 1010

Note   Commands that are identical to those documented in the Cisco IOS software documentation have been removed from this chapter.

Note   Commands that no longer function as expected in ATM environments have also been removed from this chapter.

Refer to Appendix D of this command reference for a detailed list of commands that have been removed, changed or replaced.

scheduler allocate

To guarantee CPU time for processes, use the scheduler allocate global configuration command.
To restore the default guaranteed CPU time, use the no form of this command.

Syntax Description

interrupt-time	Integer (in microseconds) that limits the maximum number of microseconds to spend on fast switching within any one network interrupt context. The range is 500 to 6000 microseconds. The default is 4000 microseconds.
process-time	Integer (in microseconds) that guarantees the minimum number of microseconds to spend at the process level when network interrupts are disabled. The range is 500 to 60000 microseconds. The default is 200 microseconds.

Defaults

Approximately five percent of the CPU is available for process tasks.

Command Modes

Global configuration

Command History

Release	Modification
11.2(8.0.1)	New command

Usage Guidelines

The normal operation of the network server allows the switching operations to use as much of the central processor as required. If the network is running unusually heavy loads that do not allow the processor the time to handle the routing protocols, give priority to the system process scheduler.
Use the scheduler allocate command to guarantee processor time.

Examples

The following example makes 20 percent of the CPU available for process tasks.

Switch(config)# scheduler allocate 2000 500

scope

To filter ATM signalling call failures that occur within the switch and on other switches, use the scope ATM signalling diagnostics configuration command. To disable this feature, use the no form of this command.

Syntax Description

all	Filter call failures that occur within the switch or on other external switches.
external	Filter call failures that occur on other external switches.
internal	Filter call failures that occur within the switch.

Defaults

all

Command Modes

ATM signalling diagnostics configuration

Command History

Release	Modification
11.2(8.0.1)	New command

Examples

In the following example, call failures are filtered by failures that occur within the switch.

Switch(cfg-atmsig-diag)# scope internal

scope map

To specify the mapping from a range of organizational scope values (used at UNI interfaces) to a PNNI scope value (such as in terms of PNNI routing-level indicators), use the scope map PNNI node-level subcommand. To set to default a range of organizational scope values, use the no form of this command.

Syntax Description

low-org-scope	Specifies the low end of the range of organizational scope values. The valid range of organizational scope values is from local (1) to global (15).
high-org-scope	Specifies the high end of the range of organizational scope values. The valid range of organizational scope values is from local (1) to global (15). If no value is specified, then the range includes only one entry (for example, high-org-scope equals low-org-scope).
level-indicator	Specifies the PNNI scope value to which the range of organizational scope values is mapped. The range is from 0 to 104.

Defaults

Table Table 17-1 shows the default values specified in the ATM Forum PNNI 1.0 Specifications.

Table 17-1: Organizational Scope-to-Default Level Mappings

org-scope Range	ATM Forum Default Level
1-3	96
4-5	80
6-7	72
8-10	64
11-12	48
13-14	32
15 global	0

The scope map command is used to change the values of specific entries. This command is only accepted when the scope mode is set to manual.

When the organizational scope of a registered address maps to a PNNI level that is lower in the PNNI hierarchy (larger PNNI routing level) than the level of this node, the registered address is not advertised. Similarly, when the connection scope of a setup attempt maps to a PNNI level that is lower in the PNNI hierarchy than the level of this node, then only destinations directly attached to this switch router are considered acceptable.

Note   Modifying the node level without altering the scope map table can result in some advertisements being suppressed.

The ATM switch router provides an option to automatically adjust the level changes. In automatic mode, the default scope map table is tied to the level of the node when it is generated.

Note that the default organizational scope of an individual address is global (15), and the default organizational scope of a group address is local (1).

Examples

The following example shows setting the scope mode to manual and setting the scope map entries for organizational scope values 1 through 5 to PNNI level 96, using the scope map PNNI node-level subcommand.

Switch# configure terminal
Switch(config)# atm router pnni
Switch(config-atm-router)# node 1
Switch(config-pnni-node)# scope mode manual
Switch(config-pnni-node)# scope map 1 5 level 96

Related Commands

Command	Description
scope mode	Specifies the configuration mode of the mapping from organizational scope values (used at UNI interfaces) to PNNI scope (such as PNNI routing-level indicators).
show atm pnni scope	Displays the mapping from organizational scope values—used at UNI interfaces—to PNNI scope (such as PNNI routing level indicators).

scope mode

To specify the configuration mode of the mapping from organizational scope values (used at UNI interfaces) to PNNI scope (such as PNNI routing-level indicators), use the scope mode node-level subcommand.

Syntax Description

automatic	Generates a default scope mapping table automatically which is tied to the PNNI level of the node. In this mode, no modifications of the scope mapping table entries are allowed.
manual	Allows for manual configuration of the scope mapping table using the scope map command.

Defaults

The default scope mappings for automatic are shown in Table 17-2.

Table 17-2: Default Scope Mappings for Automatic Mode

Organizational Scope Range	ATM Forum Default Level	Automatic Mode Level
1-3	96	min(l,96)
4-5	80	min(l,80)
6-7	72	min(l,72)
8-10	64	min(l,64)
11-12	48	min(l,48)
13-14	32	min(l,32)
15(global)	0	0

Note that the scope mapping table is overwritten whenever the scope mode is changed from manual to automatic (for example, all scope map commands for this node are removed).

Examples

The following example shows setting the scope mode to manual using the scope mode PNNI node-level subcommand.

Switch# configure terminal
Switch(config)# atm router pnni
Switch(config-atm-router)# node 1
Switch(config-pnni-node)# scope mode manual

Related Commands

Command	Description
scope map	Specifies the mapping from a range of organizational scope values (used at UNI interfaces) to a PNNI scope value (such as PNNI routing-level indicators).
show atm pnni scope	Displays the mapping from organizational scope values—used at UNI interfaces—to PNNI scope (such as PNNI routing level indicators).

scrambling

To allow scrambling to be enabled or disabled from the current port, use the scrambling interface configuration command. To disable scrambling, use the no form of this command.

Syntax Description

scramblingmode

Specify either sts-stream or cell-payload.

Defaults

In SONET interfaces, both modes are enabled. In DS3 interfaces, the mode is disabled.

Command Modes

Interface configuration

Command History

Release	Modification
11.1(4)	New command

Usage Guidelines

The sts-stream scrambling is applicable only to SONET interfaces.

Examples

The following example shows how to disable sts-stream and cell-payload scrambling on the physical device associated with ATM 3/0/0.

Switch# configure terminal
Switch(config)# interface atm 3/0/0
Switch(config-if)# no scrambling cell-payload
Switch(config-if)# no scrambling sts-stream

segment-target

To specify a target entry in a partially specified PNNI explicit-path, use the segment-target PNNI explicit-path configuration command.

Syntax Description

name-string	Name of the PNNI node.
node-id	Full 22-byte node ID for a PNNI node.
node-id-prefix	The first 15 or more bytes of a node ID for a PNNI node.
port hex-port-id	Optionally specifies an exit port to exclude for a PNNI node. Should be specified as a hexadecimal port ID rather than as a port name. The default is to allow any valid exit port.
agg-token hex-agg-token-id	Optionally specifies the exit aggregation token, which is used in place of the port ID for higher-level PNNI LGNs. The default allows any valid exit port.

Defaults

See "Syntax Description."

Command Modes

PNNI explicit-path configuration

Command History

Release	Modification
12.0(3c)W5(9)	New command

Usage Guidelines

Note   See the atm pnni explicit-path command for a description of how to edit or delete an existing segment-target path entry.

Node IDs can be entered with either the full 22-byte length address, or as a node ID prefix with a length of 15 bytes or more. To specify routes that include higher-level nodes (parent LGNs) for other peer groups, we recommend that you enter exactly 15 bytes so that the address remains valid in the event of a PGL update.

Node IDs appear in the following format:

  dec: dec: 13-20 hex digits

Note   To display the node IDs that correspond to named nodes in a network, use either the show atm pnni identifier command or the show atm pnni topology command with the node keyword.

Node names can be entered instead of node IDs. If names are used to identify higher-level LGNs, the resulting explicit paths are not guaranteed to remain valid if the PGL changes in the neighboring peer group. To prevent invalid paths, configure all parent LGNs (for all potential PGL nodes) with the same node name.

An exit port can be specified for any entry. The port should be specified as a hexadecimal port ID rather than as a port name. For excluded entries, only this port is excluded from the path.

Note   To display the corresponding hexadecimal port IDs for a node, use either the show atm pnni identifier command with the port keyword, or the show atm pnni topology command with the node and hex-port-id keywords.

Since the port-id could change if the following neighbor peer group changes PGL leaders, the aggregation token is used in place of the port ID for nodes with higher-level LGNs. The LGN aggregation token can only identify the port uniquely if the following entry is the next-node entry. Aggregation tokens are not allowed for excluded tokens.

Examples

The following example shows how to perform the following PNNI explicit-path configuration tasks:

• Enter PNNI explicit-path configuration mode

• Add one next-node

• Add two segment-target nodes (these must appear in their desired routing order.)

• Specify an LGN node by its 15-byte node ID prefix

• Exit PNNI explicit-path configuration mode

Switch# configure terminal
Switch(config)# atm pnni explicit-path name boston_2.path1
Switch(cfg-pnni-expl-path)# next-node dallas_2
Switch(cfg-pnni-expl-path)# segment-target dallas_4
Switch(cfg-pnni-expl-path)# segment-target 40:72:47.009181000000106000000000

Related Commands

Command	Description
atm pnni explicit-path	Used to enter PNNI explicit path configuration mode to create or modify PNNI explicit paths.
exclude-node	Specifies a node to exclude from all segments of a partially specified ATM PNNI explicit path.
next-node	Specifies the next adjacent entry in a fully-specified ATM PNNI explicit path.
show atm pnni explicit-paths	Displays a summary of explicit paths that have been configured.

service-category

To filter ATM signalling call failures by service category, use the service-category ATM signalling diagnostics configuration command. To return the service category to the default, use the no form of this command.

Syntax Description

abr	Sets the service category to ABR.
all	Sets the service category to ABR, CBR, NRT-VBR, RT-VBR, and UBR.
cbr	Sets the service category to CBR.
nrt-vbr	Sets the service category to NRT-VBR.
rt-vbr	Sets the service category to RT-VBR.
ubr	Sets the service category to UBR.

Defaults

all

Command Modes

ATM signalling diagnostics configuration

Command History

Releae	Modification
11.2(8.0.1)	New command

Examples

In the following example, call failures for the ABR and UBR service categories are filtered.

Switch# configure terminal
Switch(config)# interface atm 0/0/0
Switch(config-if)# atm signalling diagnostics 1
Switch(cfg-atmsig-diag)# service-category abr ubr

sgcp

To enable the operation of the SGCP to interconnect ATM CES interface circuits on a switch router, use the sgcp global configuration command. To disable the operation of SGCP on a switch router, use the no form of this command.

Syntax Description

This command has no arguments or keywords.

Defaults

Disabled

Command Modes

Global configuration

Command History

Release	Modification
12.0(3c)W5(9)	New command

Usage Guidelines

When enabled, SGCP listens on all interfaces for UDP packets that contain SGCP requests or responses. For call setup, SGCP allocates connections to endpoints: CES ATM single time slot circuits. For call teardown, SGCP releases connections between endpoints. The no form of the command releases all network connections established for SGCP and all endpoints from connections. It also returns resources allocated to SGCP. The no form also stops SGCP from listening for UDP packets. No attempt is made to gracefully release resources.

When SGCP receives a CreateConnection packet for the ATM switch router endpoint, the endpoint name is in the following format:

CBR.x.y.z/c
 

where x, y, and z are standard ATM switch router interface specifiers (card/subcard/interface), and c is a CES circuit ID.

For a CreateConnection packet to succeed:

• There must be a CES card in slot x, subcard y, 0<=z<=3:

  T1: 1<=c<=24

  E1: 1<=c<=31

• There must be a CES circuit defined with circuit ID c, with only a single time slot
  (time slot = c) allocated to it.

• There must be no PVC configured for the CES circuit.

• The CES circuit must not be the destination end of a CES soft PVC.

• The parent CES interface line state (shown by the show ces interface command) must be normal.

• The SGCP global operational state (shown by the show sgcp command) must be active.

Note   For SGCP to operate properly, even with the sgcp command in effect, you must not enter the sgcp graceful-shutdown command.

Examples

The following example enables SGCP.

Switch# configure terminal
Switch(config)# sgcp

Related Commands

Command	Description
sgcp call-agent	Sends SGCP response packets to a predetermined IP address and UDP port.
sgcp graceful-shutdown	Used to shut down SGCP operations gracefully.
sgcp request retries	Specifies the number of times the ATM switch sends an SGCP request to the call agent without receiving a response, and before ceasing to retry.
sgcp request timeout	Specifies the time the ATM switch waits after sending an SGCP request to the call agent before considering the request lost.
show sgcp	Displays global configuration, operational state, and a summary of connection activity for SGCP.
show sgcp connection	Displays a global list of SGCP connections or a single interface based on a related keyword.
show sgcp endpoint	Displays CES circuit endpoints that might or might not have connections created.
show sgcp statistics	Displays global statistics pertaining to SGCP activity.

sgcp call-agent

To send SGCP response packets to a predetermined IP address and UDP port, use the sgcp call-agent global configuration command. To restore the default behavior of responding to SGCP request packets using the source address in the request packet, use the no form of this command.

Syntax Description

host	String representing a DNS name or IP address for the SGCP call agent.
udp_port	Decimal UDP port number.

Defaults

Disabled

Command Modes

Global configuration

Command History

Release	Modification
12.0(3c)W5(9)	New command

Usage Guidelines

Use this command to determine the IP address and UDP port of the call agent for sending requests and responses if the call-agent address is not configured.

• The gateway sends responses to the source IP address and port specified in the UDP packet containing the SGCP request.

• The gateway sends a DeleteConnection request to the source IP address and port specified in
  the UDP packet of the CreateConnection request that allocated the current connection.

If the address is specified, but no port is specified, SGCP uses the well-known SGCP port 2427.

Examples

The following example specifies a call-agent address to use. The default UDP port is used.

Switch# configure terminal
Switch(config)# sgcp call-agent 172.69.1.129

Related Commands

Command	Description
sgcp	Enables the operation of the SGCP to interconnect ATM CES interface circuits on a switch router.
show sgcp	Displays global configuration, operational state, and a summary of connection activity for SGCP.

sgcp graceful-shutdown

To shut down SGCP operation, use the sgcp graceful-shutdown global configuration command.
To allow SGCP to resume operation, use the no form of this command.

Syntax Description

This command has no arguments or keywords.

Defaults

Disabled

Command Modes

Global configuration

Command History

Release	Modification
12.0(3c)W5(9)	New command

Usage Guidelines

The graceful shutdown configuration is used while SGCP is active. This command stops SGCP operation after attempting to notify the call agent about the release of any connections in progress.

The no sgcp command operates in a similar manner in that any active network connections established by SGCP are torn down.

The gateway also sends DeleteConnection requests to the call agent for all endpoints allocated to connections. After responses (or retransmission limits, or call agent-initiated DeleteConnection) have been received for all connections, the gateway stops listening to UDP. During this activity, SGCP rejects any requests for new connections.

After you enter the sgcp graceful-shutdown command with SGCP enabled, the operational state of SGCP that theshow sgcp command reflects can be Down or Going Down. The Going Down state is entered only if there are active connections. Once all connections are inactive (not allocated and network connection released), the global operational state is Down. While sgcp is outstanding, the no form of this command resumes SGCP operation.

The no form of this command has no effect when issued while SGCP is not operating.

Examples

Switch# configure terminal
Switch(config)# sgcp grace-shutdown
 

Related Commands  

Command	Description
sgcp	Enables the operation of the SGCP to interconnect ATM CES interface circuits on a switch router.
show sgcp	Displays global configuration, operational state, and a summary of connection activity for SGCP.

sgcp request retries

To specify the number of times the ATM switch router sends an SGCP request to the call agent without receiving a response and before ceasing to retry, use the sgcp request retries global configuration command. To restore the default value, use the no form of this command.

Syntax Description

retryval

Decimal number of retries.

Defaults

Three

Command Modes

Global configuration

Command History

Release	Modification
12.0(3c)W5(9)	New command

Usage Guidelines

Currently, the ATM switch router sends only DeleteConnection requests to the call agent. When UDP is sending packets, there is no assurance that all packets are received. When the number of specified retries has been exceeded, the response to DeleteConnection appears to the ATM switch as positive.

Examples

The following example sets the number of request retries to six.

Switch# configure terminal
Switch(config)# sgcp request retries 6

Related Commands

Command	Description
sgcp	Enables the operation of the SGCP to interconnect ATM CES interface circuits on a switch router.
sgcp request timeout	Specifies the time the ATM switch waits after sending an SGCP request to the call agent before considering the request lost.
show sgcp	Displays global configuration, operational state, and a summary of connection activity for SGCP.

sgcp request timeout

To specify the time the ATM switch router waits after sending an SGCP request to the call agent before considering the request lost, use the sgcp request timeout global configuration command. To restore the default value, use the no form of this command.

Syntax Description

timeval

Time value, in milliseconds.

Defaults

500 milliseconds

Command Modes

Global configuration

Command History

Release	Modification
12.0(3c)W5(9)	New command

Usage Guidelines

Currently, the ATM switch router only sends DeleteConnection requests to the call agent.

Examples

The following example sets the request timeout to one second.

Switch# configure terminal
Switch(config)# sgcp request timeout 1000

Related Commands

Command	Description
sgcp	Enables the operation of the SGCP to interconnect ATM CES interface circuits on a switch router.
show sgcp	Displays global configuration, operational state, and a summary of connection activity for SGCP.

slip

Use the slip EXEC command to attach or detach a SLIP interface.

Syntax Description

This command has no keywords or arguments.

Command Modes

EXEC

Command History

Release	Modification
11.1(4)	New command

snmp-server enable traps

To enable the router to send SNMP traps, use the snmp-server enable traps global configuration command. To disable SNMP and stop sending traps, use the no form of this command.

Syntax Description

trap-type

Type of trap to enable. If no type is specified, all traps are sent (including envmon and repeater). trap-type can have one of the following values: atm-accounting—Enable SNMP ATM accounting traps. chassis-change—Enable SNMP chassis change traps. chassis-fail—Enable SNMP chassis fail traps. config—Enable SNMP configuration traps. entity—Enable SNMP entity traps. snmp—Enable SNMP traps. syslog—Enable SNMP syslog traps.

trap-option

Enables authentication. When the snmp keyword is used for trap-type, you can specify the authentication option to enable SNMP Authentication Failure traps. (The snmp-sever enable traps snmp authentication command replaces the snmp-server trap-authentication command.) If no option is specified, all SNMP traps are enabled.

Defaults

No traps are enabled.

If you enter this command with no keywords, the default is to enable all trap types.

Command Modes

Global configuration

Command History

Release	Modification
12.0(1a)W5(5b)	New command

Usage Guidelines

Use the snmp-server enable command to specify which SNMP traps the switch router sends, and use the snmp-server host command to specify which host or hosts receive SNMP traps.

You must issue a separate snmp-server enable command for each trap type, including envmon
and repeater.

sonet

To set the mode of operation and control the type of ATM cell used for cell-rate decoupling on the SONET, use the sonet interface configuration command. To restore the default operation to OC-3, OC-12, and OC-48c interfaces, use the no form of this command.

Catalyst 8540 MSR

sonet {stm-1 | sts-3c} | {stm-4c | sts-12c} | {stm-16 | sts-48c}

no sonet {stm-1 | sts-3c} | {stm-4c | sts-12c} | {stm-16 | sts-48c}

Catalyst 8510 MSR and LightStream 1010

sonet {stm-1 | sts-3c} | {stm-4c | sts-12c}

no sonet {stm-1 | sts-3c} | {stm-4c | sts-12c}

Syntax Description

stm-1	Synchronous Transport Module level 1. SDH/STM-1 operation (ITU-T specification).1
sts-3c	Synchronous Transport Signal level 3, concatenated (3 x 51.84 Mbps). SONET format that specifies the frame structure for the 155.52 Mbps lines used to carry ATM cells.
stm-4c	Synchronous Transport Module level 4. SDH/STM-4 operation (ITU-T specification).
sts-12c	Synchronous Transport Signal level 12, concatenated (12 x 51.84 Mbps). SONET format that specifies the frame structure for the 5184 Mbps lines used to carry ATM cells.
stm-16	Synchronous Transport Module level 16. SDH/STM-16 operation (ITU-T specification). (Catalyst 8540 MSR).
sts-48c	Synchronous Transport Signal level 48, concatenated. (48 x 51.84 Mbps) SONET format that specifies the frame structure for the 2488.32 Mbps lines used to carry ATM cells. (Catalyst 8540 MSR).

1The ITU-T carries out the functions of the former Consultative Committee for International Telegraph and Telephone (CCITT).

Defaults

For OC-3: sts-3c.

For OC-12: sts-12c.

For OC-48c: sts-48c.

Command Modes

Interface configuration

Command History

Release	Modification
11.1(4)	New command

Usage Guidelines

This command applies to all ports except the CPU. Use stm-1, stm-4c and stm-16 in applications where the ATM switch router requires idle cells for rate adaptation. An idle cell contains 31 zeros followed by a 1.

Use the appropriate default in applications where the ATM switch router requires unassigned cells for rate adaptation. An unassigned cell contains 32 zeros.

Examples

The following example specifies ATM SONET STM-1.

Switch(config-if)# sonet stm-1

Related Commands

Command	Description
show controllers	Displays information about a physical port device.
show running-config	Displays the configuration information currently running on the terminal.
sonet overhead	Used to set SONET/SDH overhead bytes.
sonet report	Enables the reporting of selected alarms.
sonet threshold	Used to set the BER threshold values.

sonet overhead

To set SONET/SDH overhead bytes, use the sonet overhead interface configuration command.
To restore the default value, use the no form of this command.

Syntax Description

c2	Sets path signal label indicator.
bytes	Specifies byte value in the range of 0 to 255.
j0	Sets string or repeating value (applicable only in STM mode).
msg	Specifies string to be transmitted.
line	Specifies text consisting of characters.
j1	Sets 64/16-byte format, 0x0 by default.
16byte	Sets 16-byte format message starting with country code or three alphabetic country code.
exp-msg	Specifies expected message.
64byte	Sets 64-byte format message.
s1s0	Specifies bit S1 and S0 of H1.
bits	Specifies bit value in the range of 0 to 3.

Defaults

64-byte message

Command Modes

Interface configuration

Command History

Release	Modification
12.0(4a)W5(11a)	New command

Usage Guidelines

By default, the path trace message is a free format 64-byte string consisting of hostname, interface name, and IP address information. This format is compatible with the default GSR POS j1 message.

Note   This command is only supported on a system with an OC-12 or OC-48c interface module.

Examples

The following example sets the sonet overhead path signal indicator to 255 bytes on ATM 10/0/0.

Switch(config)# int atm 10/0/0
Switch(config-if)# sonet overhead c2 255

Related Commands

Command	Description
show controllers	Displays information about a physical port device.
sonet	Used to set the mode of operation and control the type of ATM cell used for cell-rate decoupling on the SONET.
sonet report	Enables the reporting of selected alarms.
sonet threshold	Used to set the BER threshold values.

sonet report

To enable the reporting of selected alarms, use the sonet report interface configuration command. To revert to the default, or to disable selected alarms, use the no form of this command.

Syntax Description

slos	Enables reporting section loss of signal.
slof	Enables reporting section loss of frame.
lais	Enables reporting line alarm indication signal.
lrdi	Enables line remote defect indication.
pais	Enables path alarm indication signal.
prdi	Enables path remote defect indication.
plop	Enables reporting path loss of pointer.
sd-ber	Enables reporting LBIP BER in excess of SD threshold.
sf-ber	Enables reporting LBIP BER in excess of SF threshold.
b1-tca	Enables B1 (selection error) BER threshold crossing alarm.
b2-tca	Enables B2 (line error) BER threshold crossing alarm.
b3-tca	Enables B3 (BIP-8 error) BER threshold crossing alarm.

Defaults

By default, alarm reporting is enabled for slos, slof, plop, sf, b1-tca, b2-tca, b3-tca.

Command Modes

Interface configuration

Command History

Release	Modification
12.0(4a)W5(11a)	New command

Usage Guidelines

This command enables the reporting of the selected alarms listed in the "Syntax Description."

Note   This command is only supported on a system with an OC-12 or OC-48c interface module.

Examples

The following example enables the section loss of signal reporting:

Switch(config-if)# sonet report slos

Related Commands

Command	Description
show controllers	Displays information about a physical port device.
sonet	Used to set the mode of operation and control the type of ATM cell used for cell-rate decoupling on the SONET.
sonet overhead	Used to set SONET/SDH overhead bytes.
sonet threshold	Used to set the BER threshold values.

sonet threshold

To set the BER threshold values, use the sonet threshold interface configuration command.
To disable the threshold values, use the no form of this command.

Syntax Description

sd-ber	Sets signal degrade BER threshold and displays any signal degradation.
sf-ber	Sets signal fail BER threshold and displays any signal failure.
bl-tca	Sets b1 (selection error) BER threshold crossing alarm. This alarm indicates trouble at the section layer of the SONET infrastructure; SONET circuits need to be checked out.
b2-tca	Sets b2 (line error) BER threshold crossing alarm. This alarm indicates trouble at the Line/Multiplexer layer of the SONET infrastructure; SONET network elements in this circuit need to be checked out.
b3-tca	Sets b3 (path BIP error) BER threshold crossing alarm. This alarm indicates trouble at the path layer (end to end) of the SONET infrastructure; SONET network elements in this circut need to be checked out.
ber	Specifies BER in the range of 3 to 9 (10 to minus n).

Defaults

For BER thresholds: sf = 10e-3, sd = 10e-6
For TCA thresholds: b1 = 10e-6, b2 = 10e-6, b3 = 10e-6

Command Modes

Interface configuration

Command History

Release	Modification
12.0(4a)W5(11a)	New command

Usage Guidelines

This command sets or changes the BER and threshold crossing alarms. Any errors in B1 automatically results in B2 (line) and B3 (path) errors.

Note   This command is only supported on systems with OC-12 or OC-48c interface modules.

Examples

The following example sets the b3-tca BER threshold crossing alarm to 10.

Switch(config-if)# sonet threshold b3-tca 3

Related Commands

Command	Description
show controllers	Displays information about a physical port device.
sonet	Used to set the mode of operation and control the type of ATM cell used for cell-rate decoupling on the SONET.
sonet overhead	Used to set SONET/SDH overhead bytes.
sonet report	Enables the reporting of selected alarms.

sonet tx-ais on-rx-defect

Use the sonet tx-ais on-rx-defect command to enable a SONET interface to send an alarm indication signal (AIS) if it detects the receive port has failed. To disable AIS, use the no form
of this command.

Syntax Description

This command has no arguments or keywords.

Defaults

Disabled

Command Modes

Interface Configuration

Command History

Release	Modification
12.0(3c)W5(9)	New command

Usage Guidelines

The sonet tx-ais on-rx-defect command should not be enabled on both ATM switch router interfaces connected to the same physical line. Even if no alarm exists, both interfaces will see the alarms signals and never come up.

Examples

The following example enables AIS on an ATM interface.

Switch# configure terminal
Switch(config)# interface atm 3/0/0
Switch(config-if)# sonet tx-ais on-rx-defect

Related Commands

Command	Description
show controllers	Displays information about a physical port device.

statistics

To turn on the PNNI statistics feature, use the statistics ATM router PNNI configuration command. To disable this feature, use the no form of this command.

Syntax Description

call	Specifies statistics related to route computation for call and party setups.

Defaults

Disabled

Command Modes

ATM router PNNI configuration

Command History

Release	Modification
12.0(1a)W5(5b)	New command

Usage Guidelines

For more information, refer to the ATM Switch Router Software Configuration Guide.

Examples

The following script shows how to access the statistics ATM router PNNI configuration command.

Switch# configure terminal
Switch(config)# atm router pnni
Switch(config-atm-router)# statistics call

Related Commands

Command	Description
show atm pnni statistics call	Used to display PNNI statistics.

status

To configure the status of this filter table entry, use the status ATM signalling diagnostics configuration command. To disable this feature, use the no form of this command.

Syntax Description

active	Sets status to active to begin filtering failed connections.
inactive	Sets status to inactive to stop filtering failed connections.
delete	Sets status to delete if the signalling diagnostics filter table entry needs to be deleted.

Defaults

Inactive

Command Modes

ATM signalling diagnostics configuration

Command History

Release	Modification
12.0(1a)W5(5b)	New command

Examples

The following script shows how to access the status command.

Switch# configure terminal
Switch(config)# status active

summary-address

To configure summary address prefixes on a PNNI node, use the summary-address node-level subcommand. To remove configured summary address prefixes, use the no form of this command.

Syntax Description

address-prefix	Specifies the summary address prefix. The maximum length of the address prefix is 19 bytes. Each character in the prefix is 4 bits. The length of the prefix must fall on a nibble boundary. In other words, the length of the prefix must be a multiple of 4 bits.
internal	Specifies local knowledge of reachability, including end-system addresses registered via ILMI address registration.
exterior	Specifies knowledge of reachability through remote networks or derived from other protocol exchanges outside the PNNI routing domain.
suppress	Indicates that neither the summary address nor any addresses for which the summary address is the longest matching prefix are advertised.

Defaults

Default summary addresses are controlled by the auto-summary command.

The default summary address type is internal.

Command Modes

PNNI node configuration

Command History

Release	Modification
11.1(4)	New command

Usage Guidelines

Summary addresses can be used to decrease the amount of information advertised by this PNNI node. Summary addresses should only be configured when all end-system addresses matching the summary address are reachable from this switch (for example, not reachable through PNNI interfaces to other switches).

Summary addresses of type internal only summarize internal addresses reachable from this switch (such as ILMI-registered addresses and internal static routes). Summary addresses of type exterior only summarize exterior addresses reachable from this switch (for example, exterior static routes on IISP or public UNI interfaces).

Suppressed summary addresses can be used to prevent other PNNI nodes from learning of switch connectivity to certain addresses (for example, for back doors).

For more information, refer to the ATM Switch Router Software Configuration Guide.

Examples

The following script shows how to access the summary-address node-level subcommand.

Switch# configure terminal
Switch(config)# atm router pnni
Switch(config-atm-router)# node 1
Switch(config-pnni-node)# summary-address 48.91...

Related Commands

Command	Description
atm route	Specifies a static route to a reachable address prefix.
auto-summary	Allows default summary addresses to be generated based on the switch's ATM address.
show atm route	Used to display all local or network-wide reachable address prefixes in this switch's ATM routing table.

sync config (Catalyst 8540 MSR)

To synchronize the configuration between the primary and secondary route processors based on the primary configuration, use the sync config main CPU redundancy command. To disable the synchronization, use the no form of this command.

Syntax Description

startup	Synchronizes the startup configuration.
running	Synchronizes the running configuration.
both	Synchronizes the startup and running configurations.

Defaults

both

Command Modes

Main CPU redundancy

Command History

Release	Modification
12.0(3c)W5(9)	New command

Examples

The following example synchronizes the startup configuration of the primary and secondary route processors.

Switch# configure terminal
Switch(config)# redundancy
Switch(config-r)# main-cpu
Switch(config-r-mc)# sync config startup

Related Commands

Command	Description
show functional-image-info	Displays information about the in-system programmable device images (FPGA and PLD images) for a given module in the system.

Posted: Wed Sep 6 15:51:50 PDT 2000
Copyright 1989-2000©Cisco Systems Inc.